JVC GR D90 User Manual

ENGLISH  
DIGITAL VIDEO CAMERA  
CONTENTS  
AUTOMATIC  
GR-D90  
GR-D70  
GR-D30  
DEMONSTRATION  
6
GETTING STARTED 7 – 11  
TAPE  
RECORDING &  
Please visit our Homepage on the World Wide Web for Digital  
Video Camera:  
PLAYBACK  
12 – 16  
17 – 22  
For Accessories:  
MEMORY CARD  
RECORDING &  
PLAYBACK  
ADVANCED  
FEATURES  
23 – 37  
38 – 53  
REFERENCES  
The camcorder illustrations appearing in  
this instruction manual are of the GR-D90.  
For Customer Use:  
Enter below the Model No. and Serial  
Memory card recording features are  
available on GR-D90 and GR-D70  
No. which is located on the bottom of the  
camcorder. Retain this information for  
future reference.  
Model No.  
Serial No.  
INSTRUCTIONS  
LYT1069-001B  
EN  
Dear Customer,  
Thank you for purchasing this digital video camera. Before use, please read “SAFETY PRECAUTIONS”  
and “IMPORTANT PRODUCT SAFETY INSTRUCTIONS” (pgs. 3 and 4) to ensure safe use of this  
product.  
SAFETY PRECAUTIONS  
CAUTION  
WARNING:  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
TO REDUCE THE RISK OF FIRE  
OR ELECTRIC SHOCK, DO NOT  
EXPOSE THIS APPARATUS TO  
RAIN OR MOISTURE.  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER (OR BACK).  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
The lightning flash with arrowhead symbol, within an  
equilateral triangle, is intended to alert the user to the  
presence of uninsulated "dangerous voltage" within the  
product's enclosure that may be of sufficient magnitude  
to constitute a risk of electric shock to persons.  
NOTES:  
The rating plate (serial number plate) and safety  
caution are on the bottom and/or the back of the main  
unit.  
The exclamation point within an equilateral triangle is  
intended to alert the user to the presence of important  
operating and maintenance (servicing) instructions in  
the literature accompanying the appliance.  
The rating information and safety caution of the AC  
Adapter are on its upper and lower sides.  
CAUTIONS:  
This camcorder is designed to be used with NTSC-type color television signals. It cannot be used for playback with a  
television of a different standard. However, live recording and LCD monitor/viewfinder playback are possible  
anywhere.  
Use the JVC BN-V408U/V416U/V428U battery packs and, to recharge them or to supply power to the camcorder  
from an AC outlet, use the provided multi-voltage AC Adapter. (An appropriate conversion adapter may be necessary  
to accommodate different designs of AC outlets in different countries.)  
Caution on Replaceable lithium battery  
The battery used in this device may present a fire or chemical burn hazard if mistreated.  
Do not recharge, disassemble, heat above 100°C or incinerate.  
Replace battery with Panasonic (Matsushita Electric), Sanyo, Sony or Maxell CR2025.  
Danger of explosion or Risk of fire if the battery is incorrectly replaced.  
Dispose of used battery promptly.  
Keep away from children.  
Do not disassemble and do not dispose of in fire.  
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides to  
allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear).  
Do not block the ventilation holes.  
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)  
No naked flame sources, such as lighted candles, should be placed on the apparatus.  
When discarding batteries, environmental problems must be considered and the local rules or laws governing  
the disposal of these batteries must be followed strictly.  
The apparatus shall not be exposed to dripping or splashing.  
Do not use this equipment in a bathroom or places with water.  
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,  
potted plants, cups etc.) on top of this unit.  
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)  
EN  
3
None  
This product has a fluorescent lamp that contains a small amount of mercury. Disposal of these materials may  
be regulated in your community due to environmental considerations.  
For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance:  
<http://www.eiae.org>  
Do not point the lens or the viewfinder directly into the sun. This can cause eye injuries, as well as lead to the  
malfunctioning of internal circuitry. There is also a risk of fire or electric shock.  
CAUTION!  
The following notes concern possible physical damage to the camcorder and to the user.  
When carrying, be sure to always securely attach and use the provided shoulder strap. Carrying or holding the  
camcorder by the viewfinder and/or the LCD monitor can result in dropping the unit, or in a malfunction.  
Take care not to get your finger caught in the cassette holder cover. Do not let children operate the camcorder,  
as they are particularly susceptible to this type of injury.  
Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the  
camcorder.  
CAUTION!  
Connecting cables (Audio/Video, S-Video, etc.) to the camcorder and leaving the unit on top of the TV is not  
recommended, as tripping on the cables will cause the camcorder to fall, resulting in damage.  
IMPORTANT PRODUCT SAFETY INSTRUCTIONS  
(1) Read these instructions.  
(2) Keep these instructions.  
(3) Heed all warnings.  
(10) Use only with the cart, stand,  
tripod, bracket, or table  
specified by the manufacturer,  
or sold with the apparatus.  
When a cart is used, use  
caution when moving the cart/  
apparatus combination to  
avoid injury from tip-over.  
(4) Follow all instructions.  
(5) Do not use this apparatus near water.  
(6) Clean only with dry cloth.  
(11) Unplug this apparatus during lightning storms or  
(7) Do not block any ventilation openings. Install in  
when unused for long periods of time.  
accordance with the manufacturers instructions.  
(12) Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as power-supply cord or  
plug is damaged, liquid has been spilled or objects  
have fallen into the apparatus, the apparatus has  
been exposed to rain or moisture, does not operate  
normally, or has been dropped.  
(8) Do not install near any heat sources such as  
radiators, heat registers, stoves, or other  
apparatus (including amplifiers) that produce heat.  
(9) Only use attachments/accessories specified by  
the manufacturer.  
This camcorder is designed exclusively for the digital video cassette, SD Memory Card and MultiMediaCard. Only  
cassettes marked “  
and memory cards* marked “  
or “  
can be used with this unit.  
Before recording an important scene . . .  
..... make sure you only use cassettes with the Mini DV mark  
..... make sure you only use memory cards* with the mark  
.
or  
.
..... remember that this camcorder is not compatible with other digital video formats.  
..... remember that this camcorder is intended for private consumer use only. Any commercial use without proper  
permission is prohibited. (Even if you record an event such as a show, performance or exhibition for personal  
enjoyment, it is strongly recommended that you obtain permission beforehand.)  
* Memory cards can be used with GR-D90/D70 only.  
EN  
4
None  
PROVIDED ACCESSORIES  
or  
USB Cable  
(GR-D90/D70 only)  
AC Adapter AP-V11U or AP-V13U  
Battery Pack BN-V408U  
Shoulder Strap  
CD-ROM  
(GR-D90/D70 only)  
Lens Cap (See below  
for attachment)  
Audio/Video Cable  
(ø3.5 mini-plug to  
RCA plug)  
Lithium Battery* CR2025  
(GR-D90/D70 only)  
Core Filter  
(for optional S-Video cable  
pg. 6 for attachment)  
(for remote control unit)  
Remote Control Unit*  
RM-V718U  
(GR-D90/D70 only)  
3
4
2
1
Memory Card 8 MB  
(GR-D90 only) (Already  
inserted in the camcorder)  
* A battery is pre-installed in the Remote  
Control Unit a time of shipment (with  
insulation sheet). To use the Remote  
Control Unit, remove the insulation sheet.  
Pull out by inserting  
a pointed instrument  
into the slot.  
Slot  
NOTE:  
In order to maintain optimum performance of the camcorder, provided cables may be equipped with one or more core  
filter. If a cable has only one core filter, the end that is closest to the filter should be connected to the camcorder.  
HOW TO ATTACH THE LENS CAP  
To protect the lens, attach the provided lens cap to the camcorder as shown in the illustration.  
NOTE:  
To confirm the lens cap is on correctly make sure the cap is flush to the camera.  
1 Make sure the arrow (L) is  
2
3
pointing upward.  
Arrow  
EN  
5
None  
HOW TO ATTACH THE CORE FILTER  
Attach the Core Filter(s) (if provided with your model pg. 5) to an optional cable(s). The Core Filter reduces  
interference.  
3 cm  
1
2
3
Stopper  
Wind once  
Release the  
stoppers on both  
ends of the Core  
Filter.  
Run the cable through the Core Filter, leaving approx. 3 cm  
of cable between the cable plug and the Core Filter. Wind  
the cable once around the outside of the Core Filter as  
shown in the illustration.  
Close the Core Filter until it  
clicks shut.  
Wind the cable so that it is not slack.  
NOTE:  
Take care not to damage the cable.  
When connecting cables, attach the end with the Core Filter to the camcorder.  
AUTOMATIC DEMONSTRATION  
Automatic Demonstration takes place when  
DEMO MODEis set to ON(factory-preset).  
%
Automatic Demonstration starts when there is no operation for  
about 3 minutes after the Power Switch y is set to “ ” or “  
and no cassette is in the camcorder.  
Performing any operation during the demonstration stops the  
demonstration temporarily. If no operation is performed for more  
than 3 minutes after that, the demonstration will resume.  
DEMO MODEremains ONeven if the camcorder power is  
t
turned off.  
To cancel Automatic Demonstration:  
1. Set the Power Switch y to “ ” while pressing down the Lock  
Button t located on the switch and press the MENU/VOLUME  
wheel % in. The Menu Screen appears.  
y
Sub Menu  
2. Rotate the MENU/VOLUME wheel % to select “  
and press it.  
(SYSTEM)”  
SYSTEM  
3. Rotate the MENU/VOLUME wheel % to select DEMO MODE”  
and press it. The Sub Menu appears.  
DEMO MODE  
OFF  
ON  
4. Rotate the MENU/VOLUME wheel % to select OFFand press  
it.  
5. Rotate the MENU/VOLUME wheel % to select RETURN,  
and press it twice. The normal screen appears.  
NOTE:  
If you do not detach the Lens Cap, you cannot see the actual changes of the Automatic Demonstration activated on  
the LCD monitor or viewfinder.  
EN  
6
None  
Power  
#
r
y
CHARGING THE BATTERY PACK  
1With the arrow on the battery pack pointing upward,  
push the battery pack slightly against the battery pack  
mount #, then slide up the battery pack until it locks in  
place.  
Arrow  
2Set the Power Switch y to OFF (CHARGE).  
Connect the AC Adapter to the camcorder.  
3Plug the AC Adapter into an AC outlet. The POWER/  
CHARGE lamp r on the camcorder blinks to indicate  
charging has started.  
To DC  
connector  
Battery pack  
AC Adapter  
Q
4When the POWER/CHARGE lamp r goes off,  
charging is finished. Unplug the AC Adapter from the  
AC outlet. Disconnect the AC Adapter from the  
camcorder.  
To AC outlet  
To Detach The Battery Pack:  
Slide the battery pack down slightly while sliding down  
BATT. RELEASE Q to detach it.  
Battery pack  
BN-V408U  
Charging time  
approx. 1 hr. 30 min.  
approx. 3 hrs.  
ATTENTION  
Before detaching the power source, make sure that the  
camcorders power is turned off. Failure to do so can  
result in a camcorder malfunction.  
BN-V416U (optional)  
BN-V428U (optional)  
approx. 5 hrs.  
INFORMATION  
Charging times are for a fully discharged battery pack.  
The extended-use battery pack kit is a set composed of  
a battery pack and AC Power Adapter/Charger:  
USING THE BATTERY PACK  
VU-V840 KIT : BN-V840U battery pack & AA-V15U AC  
Power Adapter/Charger  
Perform step 1 of CHARGING THE BATTERY PACK.  
VU-V856 KIT : BN-V856U battery pack & AA-V80U AC  
Power Adapter/Charger  
Approximate recording time  
Battery pack  
LCD monitor on  
Viewfinder on  
Read the kit's instruction manual before using.  
Also, by using the optional JVC VC-VBN856U DC  
Cord, it will be possible to connect BN-V840U or  
BN-V856U battery packs to the camcorder and supply  
power directly to the camcorder.  
BN-V408U  
1 hr. 10 min.  
1 hr. 40 min.  
BN-V416U  
(optional)  
2 hrs. 30 min.  
4 hrs. 20 min.  
5 hrs. 20 min.  
8 hrs. 10 min.  
3 hrs. 30 min.  
6 hrs. 20 min.  
7 hrs. 30 min.  
11 hrs. 10 min.  
BN-V428U  
(optional)  
NOTES:  
If the protective cap is attached to the battery pack,  
remove it first.  
BN-V840U  
(optional)  
During charging, the camcorder cannot be operated.  
Charging is not possible if the wrong type of battery is  
used.  
BN-V856U  
(optional)  
When charging the battery pack for the first time or after  
a long storage period, the POWER/CHARGE lamp r  
may not light. Remove the battery pack from the  
camcorder, then try charging again.  
USING AC POWER  
If a fully-charged batterys operation time remains  
extremely short, the battery is worn out. Please purchase  
a new one.  
Recording time is reduced significantly when Zoom or  
Record-Standby mode is engaged repeatedly or the LCD  
monitor is used repeatedly.  
Connect the AC Adapter to the camcorder as shown in  
the following illustration.  
The provided AC Adapter features automatic voltage  
selection in the AC range from 110 V to 240 V.  
Before extended use, it is recommended that you prepare  
enough battery packs to cover 3 times the planned  
shooting time.  
Continued on next page.  
EN  
7
GETTING STARTED  
Since the AC Adapter processes electricity internally,  
it becomes warm during use. Be sure to use it only in  
well-ventilated areas.  
The following operation stops charging:  
Set the Power Switch y to PLAY, “ ” or “ ”.  
Disconnect the AC Adapter from the camcorder.  
Unplug the AC Adapter from the AC outlet.  
Detach the battery from the camcorder.  
Grip Adjustment  
1Separate the Velcro strip.  
2Pass your right hand through the loop and grasp the  
grip.  
3Adjust your thumb and fingers through the grip, to  
easily operate the Recording Start/Stop button w and  
Power Switch y and Power Zoom Lever &. Be sure to  
fasten the Velcro strip to your preference.  
This camcorder will be automatically turned off if its power  
is supplied from the AC adapter and about 5 minutes pass  
since it has entered into the recording standby mode with  
a cassette inserted. If, under those conditions, the battery  
is attached to the camcorder, its charging will start.  
&
Using the optional AA-V40U AC Power Adapter/Charger,  
you can charge the BN-V408U/V416U/V428U battery  
pack without the camcorder. However, it cannot be used  
as an AC adapter.  
To avoid interference with reception, do not use the AC  
Adapter near a radio.  
Perform charging where the temperature is between 10°C  
and 35°C (50°F and 95°F). 20°C to 25°C (68°F to 77°F)  
is the ideal temperature range for charging. If the  
environment is too cold, charging may be incomplete.  
Charging time varies according to the ambient  
temperature and the status of the battery pack.  
y
w
About Batteries  
DANGER! Do not attempt to take the batteries apart, or  
expose them to flame or excessive heat, as it may  
cause a fire or explosion.  
Viewfinder Adjustment  
1Set the Power Switch y to “ ” or “ ” while  
pressing down the Lock Button t located on the  
switch.  
WARNING! Do not allow the battery or its terminals to  
come in contact with metals, as this can result in a  
short circuit and possibly start a fire.  
2Pull out the viewfinder fully and adjust it manually for  
The Benefits Of Lithium-Ion Batteries  
best viewability.  
Lithium-ion battery packs are small but have a large  
power capacity. However, when one is exposed to cold  
temperatures (below 10°C/50°F), its usage time  
becomes shorter and it may cease to function. If this  
happens, place the battery pack in your pocket or other  
warm, protected place for a short time, then re-attach it  
to the camcorder. As long as the battery pack itself is  
not cold, it should not affect performance.  
3Turn the Diopter Adjustment Control q until the  
indications in the viewfinder are clearly focused.  
PAUSE  
(If youre using a heating pad, make sure the battery  
pack does not come in direct contact with it.)  
q
Lithium-ion is vulnerable in colder temperatures.  
t
y
EN  
8
GETTING STARTED  
Shoulder Strap Attachment  
Loading/Unloading A Cassette  
The camcorder needs to be powered up to load or eject  
a cassette.  
1Thread the strap through the eyelet e, then fold it  
back and thread it through the buckle. Repeat the  
procedure to attach the other end of the strap to the  
other eyelet e located under the Grip Strap. Confirm  
the strap is not twisted.  
1Slide and hold OPEN/EJECT W in the direction of  
the arrow then pull the cassette holder cover open until  
it locks. The cassette holder opens automatically.  
Do not touch internal components.  
2Insert or remove a tape and press PUSH HEREto  
close the cassette holder.  
Once the cassette holder is closed, it recedes  
automatically. Wait until it recedes completely before  
closing the cassette holder cover.  
When the batterys charge is low, you may not be able  
to close the cassette holder cover. Do not apply force.  
Replace the battery with a fully charged one before  
continuing.  
e
3Close the cassette holder cover firmly until it locks  
into place.  
To Protect Valuable Recordings:  
Slide the erase protection tab on the back of the  
tape in the direction of SAVE. This prevents the  
tape from being recorded over. To record on this  
tape, slide the tab back to RECbefore loading it.  
Tripod Mounting  
CAUTION  
When attaching the camcorder to a tripod, extend its  
legs to stabilize the camcorder. It is not advised to use  
small sized tripods. This may cause damage to the unit  
by falling over.  
Make sure the  
window side  
is facing out.  
Cassette holder  
1To attach the camcorder to a tripod, align the  
direction stud and screw to the mounting socket o and  
stud hole i on the camcorder. Then tighten the screw  
clockwise. Some tripods are not equipped with studs.  
Cassette  
holder  
cover  
W
o
i
Be sure to press only the section labeled PUSH  
HEREto close the cassette holder; touching other  
parts may cause your finger to get caught in the  
cassette holder, resulting in injury or product damage.  
Approximate recording time  
Recording mode  
Tape  
SP  
LP  
30 min.  
60 min.  
80 min.  
30 min.  
60 min.  
80 min.  
45 min.  
90 min.  
120 min.  
NOTES:  
The cassette holder cannot be opened unless a power  
supply is attached.  
Continued on next page.  
EN  
9
GETTING STARTED  
It takes a few seconds for the cassette holder to open. Do  
not apply force.  
CAMERA D I SPLAY  
CAMERA D I SPLAY  
BR I GHT  
ON SCREEN  
DATE / T I ME  
T I ME CODE  
CLOCK  
LCD / TV  
AUTO  
There may be a delay after you open the cassette holder  
cover until the cassette holder opens. Do not use force.  
If you wait a few seconds and the cassette holder does  
not open, close the cassette holder cover and try again. If  
the cassette holder still does not open, turn the  
camcorder off then on again.  
OFF  
DEC 25 03  
5 : 30 PM  
CLOCK  
ADJ .  
DEC 25 03  
5 : 30 PM  
ADJ .  
RETURN  
If the tape does not load properly, open the cassette  
holder cover fully and remove the cassette. A few minutes  
later, insert it again.  
When the camcorder is suddenly moved from a cold  
place to a warm environment, wait a short time before  
opening the cassette holder cover.  
Once the cassette holder is closed, it recedes automati-  
cally. Wait until it recedes completely before closing the  
cassette holder cover.  
%
r
Closing the cassette holder cover before the cassette  
holder comes out may cause damage to the camcorder.  
Even when the camcorder is switched off, a cassette can  
be loaded or unloaded. After the cassette holder is closed  
with the camcorder switched off, however, it may not  
recede. It is recommended to turn the power on before  
loading or unloading.  
t
y
When resuming recording, once you open the cassette  
holder cover a blank portion will be recorded on the tape  
or a previously recorded scene will be erased (recorded  
over) regardless of whether the cassette holder came out  
or not. See page 14 for information about recording from  
the middle of a tape.  
Recording Mode Setting  
Set the tape recording mode depending on your  
preference.  
Date/Time Settings  
1Set the Power Switch y to “ ” while pressing  
down the Lock Button t located on the switch, and  
open the LCD monitor fully or pull out the viewfinder  
fully. The POWER/CHARGE lamp r lights and the  
camcorder is turned on.  
The date/time is recorded onto the tape at all times, but  
its display can be turned on or off during playback  
(pg. 31).  
1Set the Power Switch y to “ ” while pressing  
down the Lock Button t located on the switch, and  
open the LCD monitor fully or pull out the viewfinder  
fully. The POWER/CHARGE lamp r lights and the  
camcorder is turned on.  
2Press the MENU/VOLUME wheel % in. The Menu  
Screen appears.  
3Rotate the MENU/VOLUME wheel % to select  
(CAMERA)and press it.  
4Rotate the MENU/VOLUME wheel % to select REC  
MODEand press it. The Sub Menu appears. Select  
SPor LPby rotating the MENU/VOLUME wheel %  
and press it. Rotate the MENU/VOLUME wheel % to  
select RETURN, and press it twice. The Menu  
Screen closes.  
2Press the MENU/VOLUME wheel % in to access  
the Menu Screen.  
3Rotate the MENU/VOLUME wheel % to select  
(CAMERA DISPLAY)and press it.  
4Rotate the MENU/VOLUME wheel % to select  
CLOCK ADJ.. Press it and monthis highlighted.  
Rotate the MENU/VOLUME wheel % to input the  
month. Press it. Repeat to input the day, year, hour and  
minute. Rotate the MENU/VOLUME wheel % to select  
Audio Dubbing and Insert Editing (pg. 36) are  
possible on tapes recorded in the SP mode.  
• “LP(Long Play) is more economical, providing  
1.5 times the recording time.  
RETURN, and press it twice. The Menu Screen  
NOTES:  
closes.  
If the recording mode is switched during recording, the  
playback picture will be blurred at the switching point.  
It is recommended that tapes recorded in the LP mode on  
this camcorder be played back on this camcorder.  
During playback of a tape recorded on another  
camcorder, blocks of noise may appear or there may be  
momentary pauses in the sound.  
NOTE:  
Even if you select CLOCK ADJ., if the parameter is not  
highlighted the camcorders internal clock continues to  
operate. Once you move the highlight bar to the first date/  
time parameter (month), the clock stops. When you finish  
setting the minute and press the MENU/VOLUME wheel %  
in, the date and time begin operation from the date and  
time you just set.  
EN  
10  
GETTING STARTED  
Loading A Memory Card  
(GR-D90/D70 only)  
Picture Quality/Image Size Setting  
(GR-D90/D70 only)  
The provided memory card (GR-D90 only) is already  
inserted in the camcorder when you receive the  
camcorder.  
The Picture Quality/Image Size can be selected to best  
match your needs. Refer to the chart on page 18 for  
your selection.  
1Make sure the camcorders power is off.  
1Set the VIDEO/DSC Switch 4 to DSC, then set  
the Power Switch y to “ ” while pressing down the  
Lock Button t located on the switch. The POWER/  
CHARGE lamp r lights and the camcorder turns on.  
2Open the LCD monitor (pg. 47, u Monitor Open  
Button), then open the card cover (MEMORY CARD)  
p.  
2Press the MENU/VOLUME wheel % in. The Menu  
3Insert the memory card clipped edge first.  
Screen appears.  
Do not touch the terminal on the reverse side of the  
3Rotate the MENU/VOLUME wheel % to select  
label.  
(DSC)and press it.  
4To close the card cover p, push it until you hear a  
4Rotate the MENU/VOLUME wheel % to select  
QUALITYand press it. The Sub Menu appears.  
Rotate the MENU/VOLUME wheel % to select the  
desired mode and press it.  
click.  
To Unload A Memory Card:  
In step 3 push the memory card, which then comes out  
of the camcorder automatically. Pull it out and close the  
card cover p.  
5Rotate the MENU/VOLUME wheel % to select  
IMAGE SIZEand press it. The Sub Menu appears.  
Rotate the MENU/VOLUME wheel % to select the  
desired mode and press it.  
u
6Rotate the MENU/VOLUME wheel % to select  
RETURN, and press it twice. The Menu Screen  
closes.  
%
r
p
Label  
Clipped edge  
Memory card  
t
y
NOTES:  
Be sure to use only SD Memory Cards marked “  
Display  
or MultiMediaCards marked “  
.  
DSC  
Some brands of memory cards are not compatible with  
this camcorder. Before purchasing a memory card ,  
consult its manufacturer or dealer.  
QUAL I TY  
F I NE  
I MAGE S I ZE1024X768  
REC SELECT–  
Before using a new memory card, it is necessary to  
FORMAT the card. pg. 22.  
ATTENTION  
RETURN  
Do not insert/remove the memory card while the  
camcorder is turned on, as this may cause the memory  
card to be corrupted or cause the camcorder to  
become unable to recognize whether or not the card is  
installed.  
NOTE:  
In the 1024 x 768 mode, images are shot in 720 x 480  
pixels and they are converted and stored in the 1024 x 768  
file size.  
EN  
11  
GETTING STARTED  
Basic Recording  
%
Perform the procedures listed below before continuing.  
Power (pg. 7)  
Grip Adjustment (pg. 8)  
Viewfinder Adjustment (pg. 8)  
Load A Cassette (pg. 9)  
Recording Mode Setting (pg. 10)  
1Remove the lens cap.  
During shooting  
w
For GR-D90/D70 Owners: Open the LCD monitor  
(pg. 47, u Monitor Open Button) and set the  
VIDEO/DSC Switch 4 to “VIDEO”.  
r
180°  
90°  
2Set the Power Switch y to “ ” or “ ” while  
pressing down the Lock Button t located on the  
switch.  
(
)
CHARGE  
OFF  
PLAY  
Shooting while using the LCD monitor: Open the  
LCD monitor fully.  
Shooting while using the viewfinder: Pull out the  
viewfinder fully.  
t
y
u
4
• The POWER/CHARGE lamp r lights and the  
camcorder enters the Record-Standby mode.  
“PAUSE” 6 is displayed.  
Display  
Now  
calculating  
0
h
25m  
1h30m  
(
)
• The image will not appear simultaneously on the LCD  
monitor and the viewfinder. See “PRIORITY” in the  
SYSTEM Menu (pg. 30).  
1h30m  
1h29m  
Tape remaining time  
indicator (Approximate)  
3Press the Recording Start/Stop Button w. “  
3, 6 appears and the tally lamp 3 lights while  
recording is in progress.  
0h03m  
0h02m (Blinking)  
0h01m (Blinking)  
0h00m (Blinking)  
To Stop Recording, press the Recording Start/Stop  
Button w. The camcorder re-enters the Record-  
Standby mode.  
To Adjust The Brightness Of The Display  
1. Make sure the Power Switch y is set to “ ” and  
open the LCD monitor fully, then press the MENU/  
VOLUME wheel % in. The Menu Screen appears.  
NOTES:  
If the Record-Standby mode continues for 5 minutes, the  
camcorder’s power shuts off automatically. To turn the  
camcorder on again, push back and pull out the  
viewfinder again or close and re-open the LCD monitor.  
When a blank portion is left between recorded scenes on  
the tape, the time code is interrupted and errors may  
occur when editing the tape. To avoid this, refer to  
“RECORDING FROM THE MIDDLE OF A TAPE”  
(pg. 14).  
2. Rotate the MENU/VOLUME wheel % to select  
(CAMERA DISPLAY)” and press it.  
3. Rotate the MENU/VOLUME wheel % to select  
“BRIGHT” and press it. The Menu Screen closes and  
the bright level indicator t appears on the display.  
To cancel, press the MENU/VOLUME wheel %  
again so that the bright level indicator t disap-  
pears.  
To turn the tally lamp 3 or beep sounds off,  
pg. 30.  
When you use the LCD monitor outdoors in direct  
sunlight, the LCD monitor may be difficult to see. If this  
happens, use the viewfinder instead.  
Black spots or bright spots of light (red, green or blue)  
may appear constantly on the LCD monitor or the  
viewfinder (pg. 39).  
When the Recording Start/Stop button w is pressed, it  
may take a few seconds before actual recording starts.  
4. Rotate the MENU/VOLUME wheel % until the bright  
level indicator moves and the appropriate brightness  
is reached, then press it. The bright level indicator t  
disappears.  
• It is also possible to adjust the brightness of the  
viewfinder by closing the LCD monitor, pulling out  
the viewfinder and adjusting as described above.  
3 starts rotating when the camcorder actually  
starts recording.  
The time required to calculate and display the remaining  
tape length, and the accuracy of the calculation, may vary  
according to the type of tape used.  
“TAPE END” appears when the tape reaches its end, and  
the power goes off automatically if left in this condition for  
5 minutes. “TAPE END” also appears when a cassette at  
its end is loaded.  
EN  
12  
TAPE RECORDING  
Journalistic Shooting  
Zooming  
In some situations, different shooting angles may  
provide more dramatic results. Hold the camcorder in  
the desired position and tilt the LCD monitor in the  
most convenient direction. It can rotate 270° (90°  
downward, 180° upward).  
To produce the zoom in/out effect, or an instantaneous  
change in image magnification.  
Zoom In  
Slide the Power Zoom Lever & towards “T”.  
Zoom Out  
Slide the Power Zoom Lever & towards “W”.  
Self-Recording  
The further you slide the Power Zoom Lever &, the  
You can shoot yourself while viewing your own image  
in the LCD monitor. Open the LCD monitor and tilt it  
upward 180° so that it faces forward, then point the  
lens toward yourself and start recording.  
quicker the zoom action.  
NOTES:  
Focusing may become unstable during Zooming. In this  
case, set the zoom while in Record-Standby, lock the  
focus by using the manual focus (pg. 26), then zoom  
in or out in Record mode.  
Operation Mode  
Choose the appropriate operation mode according to  
your preference using the Power Switch y and  
VIDEO/DSC Switch 4 (GR-D90/D70 only).  
Zooming is possible to a maximum of 700X, or it can be  
switched to 16X magnification using the optical zoom  
(pg. 28).  
Zoom magnification of over 16X is done through Digital  
image processing, and is therefore called Digital Zoom.  
During Digital zoom, the quality of image may suffer.  
Digital zoom cannot be used when the VIDEO/DSC  
Switch 4 is set to “DSC” (“VIDEO/DSC Switch  
Position”).  
Macro shooting (as close as approx. 5 cm (2") to the  
subject) is possible when the Power Zoom Lever & is set  
all the way to “W”. Also see “TELE MACRO” in the Menu  
Screen on page 29.  
Power Switch Position  
:
Allows you to set various recording functions using the  
Menus. If you want more creative capabilities than Full  
Auto recording, try this mode.  
(Full Auto):  
Allows you to record using NO special effects or manual  
adjustments. Suitable for standard recording.  
OFF (CHARGE):  
Allows you to switch off the camcorder.  
&
PLAY:  
• Allows you to play back a recording on the tape.  
• Allows you to access data stored on the memory card  
or to transfer a still image stored on the memory card  
to a computer.  
4
VIDEO/DSC Switch Position (GR-D90/D70 only)  
VIDEO:  
• Allows you to record on a tape or play back a tape.  
y
If “REC SELECT” is set to “  
/
” in the DSC  
Menu Screen, still images are recorded on the  
memory card as well.  
• Zoom magnification over 16X is available (pg. 13,  
28).  
DSC:  
Allows you to record on a memory card or access data  
stored on a memory card.  
Power-Linked Operation  
When the Power Switch y is set to “ ” or “ ”, you can  
also turn on/off the camcorder by opening/closing the LCD  
monitor or pulling out/pushing in the viewfinder.  
EN  
13  
TAPE RECORDING  
Time Code  
Normal Playback  
1Load a tape (pg. 9).  
During recording, a time code is recorded on the tape.  
This code is to confirm the location of the recorded  
scene on the tape during playback.  
If recording starts from a blank portion, the time code  
begins counting from 00:00:00(minute:second:frame).  
If recording starts from the end of a previously recorded  
scene, the time code continues from the last time code  
number.  
2Set the VIDEO/DSC Switch 4 to VIDEO(GR-D90/  
D70 only), then set the Power Switch y to PLAY”  
while pressing down the Lock Button t located on the  
switch. To start playback, press 4/6 7.  
To stop playback temporarily (Still Playback), press  
4/6 7.  
To stop playback, press 5 5.  
If during recording a blank portion is left partway  
through the tape, the time code is interrupted. When  
recording is resumed, the time code starts counting up  
again from 00:00:00. This means the camcorder may  
record the same time codes as those existing in a  
previously recorded scene. To prevent this, perform  
RECORDING FROM THE MIDDLE OF A TAPEin the  
following cases;  
Press  
2
6 to rewind, or  
3
8 to fast-forward the  
tape during Stop mode.  
High-speed picture search (Shuttle Search) is  
possible by pressing 6 or 8 during playback  
(holding  
2
3
2
6 or  
3
8 down during playback  
continues search until released).  
Press the Zoom Button T ; on the remote control to  
zoom in (up to 44X), or W A to zoom out. You can  
also magnify a particular part of an image (GR-D90/  
D70 only pg. 35).  
At any time, pressing 4/6 7 resumes normal  
playback.  
When shooting again after playing back a recorded  
tape.  
When power shuts off during shooting.  
When a tape is removed and re-inserted during  
shooting.  
When shooting using a partially recorded tape.  
When shooting on a blank portion located partway  
through the tape.  
When shooting again after shooting a scene then  
opening/closing the cassette holder cover.  
Slow-Motion Playback/Playback Special Effects/  
Playback Zoom:  
Available only with the remote control (provided with  
GR-D90/D70 only, pg. 35)  
To Control The Speaker Volume:  
Rotate the MENU/VOLUME wheel % so that the  
volume level indicator T on the display moves to obtain  
the appropriate volume.  
Display  
Minutes  
ATTENTION  
Seconds  
During Shuttle Search, parts  
of the picture may not be  
clearly visible, particularly on  
the left side of the screen.  
Frames  
(30 frames = 1 second)  
12 : 34 : 24  
Frames are not displayed  
during recording.  
RECORDING FROM THE MIDDLE OF A TAPE  
1Play back a tape or use Blank Search (pg. 15) to  
find the spot at which you want to start recording, then  
engage the Still Playback mode (pg. 14, Normal  
Playback).  
2Set the Power Switch y to “ ” or “ ” while  
pressing down the Lock Button t located on the  
switch, then start recording.  
NOTES:  
The time code cannot be reset.  
During fast-forwarding and rewinding, the time code  
indication does not move smoothly.  
The time code is displayed only when TIME CODEis  
set to ON(pg. 31).  
EN  
14  
TAPE RECORDING  
TAPE PLAYBACK  
Blank Search  
7
8
6
5
% &  
Helps you find where you should start recording in the  
middle of a tape to avoid time code interruption  
(pg. 14).  
1Load a tape (pg. 9).  
2Set the VIDEO/DSC Switch 4 to VIDEO(GR-D90/  
D70 only), then set the Power Switch y to PLAY”  
while pressing down the Lock Button t located on the  
switch.  
3Press BLANK SEARCH *.  
Speaker  
4
• “BLANK SEARCHQ appears and the camcorder  
automatically starts reverse or forward shuttle search,  
then stops at the spot which is about  
y
3 seconds of tape before the beginning of the  
detected blank portion.  
To cancel Blank Search midway . . .  
..... press 5 5.  
NOTES:  
If Stop mode continues for 5 minutes when power is  
supplied from a battery, the camcorder shuts off  
automatically. To turn on again, set the Power Switch y  
to OFF (CHARGE), then to PLAY.  
NOTES:  
In step 3, if the current position is at a blank portion the  
camcorder searches in the reverse direction, and if the  
current position is at a recorded portion the camcorder  
searches in the forward direction.  
The playback picture can be viewed in the LCD monitor,  
viewfinder or on a connected TV (pg. 16).  
You can also view the playback picture on the LCD  
monitor with it flipped over and pushed against the  
camera body.  
LCD monitor/viewfinder indications:  
When power is supplied from a battery: the “  
battery pack remaining power indicator is displayed.  
When power is supplied from an AC outlet: “  
not appear.  
During Stop mode, none of the indications are  
displayed.  
When a cable is connected to the AV connector, the  
Blank Search does not work if HEAD CLEANING  
REQUIRED. USE CLEANING CASSETTEhas appeared  
with the tape.  
If the beginning or end of the tape is reached during  
Blank Search, the camcorder stops automatically.  
A blank portion which is shorter than 5 seconds of tape  
may not be detected.  
The detected blank portion may be located between  
recorded scenes. Before you start recording, make sure  
there is no recorded scene after the blank portion.  
does  
sound is not heard from the speaker.  
If still playback continues for more than about 3 minutes,  
the camcorders Stop mode is automatically engaged.  
When 4/6 7 is pressed to engage still playback, the  
image may not pause immediately while the camcorder  
stabilizes the still image.  
*
t
y
EN  
15  
TAPE PLAYBACK  
Connections  
These are some basic types of connections. When  
making the connections, refer also to your VCR and TV  
instruction manuals.  
To AV (  
Connector  
cover*  
1Make sure all units are turned off.  
2Connect the camcorder to a TV or VCR as shown  
in the illustration.  
If using a VCR . . . go to step 3.  
If not . . . go to step 4.  
To  
S-VIDEO )  
Audio/Video  
cable  
3Connect the VCR output to the TV input, referring to  
(provided)  
your VCRs instruction manual.  
4Turn on the camcorder, the VCR and the TV.  
5Set the VCR to its AUX input mode, and set the TV  
S-Video cable  
(optional)  
to its VIDEO mode.  
Yellow to  
To choose whether or not the following displays  
appear on the connected TV . . .  
VIDEO IN***  
Red to  
AUDIO R IN**  
Date/Time  
..... set DATE/TIMEto AUTO, ONor OFFin the  
Menu Screen (pg. 30, 32).  
White to  
Or, press DISPLAY l on the remote control  
(provided with GR-D90/D70 only) to turn on/off the  
date indication.  
AUDIO L IN**  
To S-VIDEO IN  
To TV or VCR  
VCR  
Time Code  
..... set TIME CODEto ONor OFFin the Menu  
Screen (pg. 31, 32).  
Indications other than date/time and time code  
..... set ON SCREENto LCD, LCD/TVor OFFin  
the Menu Screen (pg. 30, 32).  
TV  
NOTES:  
*
When connecting the cable, open this cover.  
It is recommended to use the AC Adapter as the  
power supply instead of the battery pack (pg. 7).  
To monitor the picture and sound from the camcorder  
without inserting a tape or memory card, set the  
camcorders Power Switch y to “ ” or “ ”, then set  
your TV to the appropriate input mode.  
** The Audio cable is not required for watching still images  
only.  
*** Connect when an S-Video cable is not used.  
GR-D90/D70 only  
Make sure you adjust the TV sound volume to its  
minimum level to avoid a sudden burst of sound when the  
camcorder is turned on.  
If you have a TV or speakers that are not specially  
shielded, do not place the speakers adjacent to the TV as  
interference will occur in the camcorder playback picture.  
If no image is displayed or no sound is heard from the TV,  
set S/AV INPUTto OFFin the Menu Screen  
(GR-D90/D70 only, pg. 31).  
While the Audio/Video cable is connected to the AV  
connector, sound cannot be heard from the speaker.  
EN  
16  
TAPE PLAYBACK  
Basic Shooting (Snapshot)  
^
You can use your camcorder as a digital still camera for  
taking snapshots.  
Perform the procedures listed below before continuing.  
Power (pg. 7)  
4
Grip Adjustment (pg. 8)  
Viewfinder Adjustment (pg. 8)  
Loading A Memory Card (pg. 11)  
Picture Quality/Image Size Setting (pg. 11)  
1Set the VIDEO/DSC Switch 4 to “DSC”, then set  
the Power Switch y to “ ” or “ ” while pressing  
down the Lock Button t located on the switch. Open  
the LCD monitor fully or pull out the viewfinder fully.  
t
y
2Press SNAPSHOT ^. “PHOTO” y appears while  
the snapshot is being taken.  
Image Size pg. 11  
The image is recorded on the memory card.  
Shooting icon pg. 48, 49  
• Still images are recorded in the snapshot mode with  
no frame.  
Card icon pg. 48, 49  
To Delete Unwanted Still Images . . .  
..... when unwanted still images are stored in the  
memory card or its memory is full, refer to  
“Deleting Files” (pg. 20) and delete unwanted  
still images.  
1024  
15  
Remaining number of shots  
pg. 48, 49  
(Approximate Number of  
Storable Images pg. 18)  
To Remove The Shutter Sound . . .  
..... when you do not want to hear the shutter sound,  
set “BEEP” to “OFF” in the Menu Screen  
(pg. 30). The sound is no longer heard from the  
speaker.  
Display  
Picture Quality pg. 11  
NOTES:  
Even if “DIS” is set to “ON” (pg. 29), the Stabilizer will  
be disabled.  
If Snapshot recording is not possible, “PHOTO” y blinks  
when SNAPSHOT ^ is pressed.  
If Program AE with special effects (pg. 23) is  
engaged, certain modes of Program AE with special  
effects are disabled during Snapshot recording. In such a  
case, the icon blinks.  
To Protect Valuable Files (available only for SD  
Memory Card) . . .  
Write/erase  
protection tab  
If shooting is not performed for approx. 5 minutes when  
the Power Switch y is set to “ ” or “ ” and power is  
supplied from the battery pack, the camcorder shuts off  
automatically to save power. To perform shooting again,  
close the LCD monitor and re-open it. When using the  
viewfinder, push back it in and pull it out again.  
The Motor Drive mode (pg. 25) is disabled when the  
VIDEO/DSC Switch 4 is set to “DSC”.  
.....slide the write/erase protection tab on the side  
of the memory card in the direction of “LOCK”.  
This prevents the memory card from being  
recorded over. To record on this memory card,  
slide the tab back to the position opposite to  
“LOCK” before loading it.  
Still images taken are compliant to DCF (Design rule for  
Camera File system). They do not have any compatibility  
with devices which are not compliant to DCF.  
EN  
17  
MEMORY CARD RECORDING  
(GR-D90 and GR-D70 only)  
Approximate Number of Storable Images  
Normal Playback  
Image Size/  
Picture  
SD Memory Card (optional)  
1Load a memory card (pg. 11).  
8MB  
20  
16MB  
32MB  
64MB  
Quality  
2Set the VIDEO/DSC Switch 4 to DSC, then set  
the Power Switch y to PLAYwhile pressing down the  
Lock Button t.  
1024 x 768/  
FINE  
45  
95  
190  
1024 x 768/  
STANDARD  
A stored image is displayed.  
65  
45  
145  
95  
310  
205  
625  
605  
405  
3Press  
3
8 to display the next image, or press  
2
640 x 480/  
FINE  
6 to display the previous image.  
To Magnify The Stored Images  
640 x 480/  
STANDARD  
Press the Zoom Button T ; on the remote control to  
zoom in (up to 44X), or W A to zoom out. You can also  
magnify a particular part of an image (pg. 35). By  
160  
295  
1215  
pressing 4/6 7,  
3
8,  
2
6, INDEX !, INFO 0  
Approximate Number of Storable Images  
magnification returns to normal instantly.  
Image Size/  
MultiMediaCard  
Picture  
To Adjust The Brightness Of The Display  
8MB*  
16MB** 32MB**  
Quality  
1. Make sure the VIDEO/DSC Switch 4 is set to  
DSCand the Power Switch y is set to “ ”, then  
press the MENU/VOLUME wheel %.  
1024 x 768/  
FINE  
24  
48  
100  
320  
215  
645  
1024 x 768/  
STANDARD  
75  
55  
160  
105  
320  
2. Perform steps 3 and 4 of To Adjust The Brightness  
Of The Displayon page 12.  
640 x 480/  
FINE  
NOTES:  
640 x 480/  
STANDARD  
Pressing INFO 0 gives you details on the displayed file  
190  
(pg. 19, Viewing File Information).  
You can also overview several files at a time  
(pg. 19, Index Playback).  
* Provided with GR-D90 only ** Optional  
You can turn off the on-screen playback display  
(pg. 19, Removing On-Screen Display).  
Images shot in a file size that is not compatible with this  
camcorder will be displayed as reduced-size thumbnail  
images. These thumbnail images cannot be transferred  
to a PC.  
NOTE:  
The number of storable images depends on the selected  
picture quality as well as the composition of the subjects in  
the images and the type of memory card being used.  
Images shot with devices (such as JVC GR-DVM70) that  
are not compatible with DCF cannot be viewed with this  
camcorder; UNSUPPORTED FILE!will be displayed.  
[For Normal Playback]  
To display the  
next image  
To display the  
previous image  
100 - 0010  
100 - 0011  
Display  
[For Auto Playback]  
EN  
18  
MEMORY CARD RECORDING  
(GR-D90 and GR-D70 only)  
MEMORY CARD PLAYBACK  
(GR-D90 and GR-D70 only)  
Viewing File Information  
7
8
6
5
&
%
You can get the relevant file information by pressing the  
INFO button 0 during normal playback or Index  
playback.  
t
y
Info Screen  
FOLDER  
F I LE  
: 1 0 0 JVCGR  
: DVC0 0 0 1 0  
:MAR 2 7 ’ 0 3  
: 1 0 2 4X7 6 8  
(
)
CHARGE  
OFF  
PLAY  
DATE  
S I ZE  
QUAL I TY : F I NE  
PROTECT : OFF  
4
0 !  
FOLDER : Folder name (pg. 22)  
FILE  
DATE  
SIZE  
: File name (pg. 22)  
: Date the file was made  
: Image size (pg. 11)  
Auto Playback  
You can run through all the images stored on memory  
automatically.  
QUALITY : Picture quality (pg. 11)  
PROTECT : When set to ON, the file is protected from  
accidental erasure (pg. 20).  
1Perform steps 1 and 2 of Normal Playback”  
(pg. 18).  
Press INFO 0 again to close the Info Screen.  
2Press 4/6 7.  
NOTE:  
If you press  
2
6 during Auto Playback, images are  
With images shot with another device or processed on a  
displayed in descending order.  
If you press  
PC, QUALITY: – – –” will be displayed.  
3
8 during Auto Playback, images are  
displayed in ascending order.  
3To end Auto Playback, press 5 5.  
Removing On-Screen Display  
NOTE:  
1Perform steps 1 and 2 of Normal Playback”  
Even if you shoot a new image after playing back a  
low-numbered one, this will not overwrite an existing image,  
because new images are automatically stored after the  
last-recorded one.  
(pg. 18).  
2Press the MENU/VOLUME wheel % in. The Menu  
Screen appears. Rotate the MENU/VOLUME wheel %  
to select DISPLAY, then press it.  
3Rotate the MENU/VOLUME wheel % to select  
Index Playback  
OFF, then press it. The operation mode indicator,  
folder/file number indicator and battery indicator (  
disappear.  
)
You can view several different files stored on the  
memory card at a time. This browsing capability makes  
it easy to locate a particular file you want.  
To display the indicators again, select ONin step 3.  
1Perform steps 1 and 2 of Normal Playback”  
Operation  
mode indicator  
Folder and file  
(pg. 18).  
number indicator  
2Press INDEX !. The Index Screen appears.  
100 - 0010  
Playback  
3Rotate the MENU/VOLUME wheel % to move the  
Screen  
frame to the desired file.  
Pressing  
displays the previous page.  
3
8 displays the next page and  
2
6
Pressing INFO 0 gives you details on the currently  
selected file (Viewing File Information).  
Battery indicator  
4Press the MENU/VOLUME wheel % in. The  
selected file is displayed.  
Index  
Screen  
1
4
7
2
5
8
3
6
9
Selected image  
Index number  
EN  
19  
MEMORY CARD PLAYBACK  
(GR-D90 and GR-D70 only)  
Protecting Files  
Deleting Files  
The Protect mode helps prevent the accidental erasure  
of files.  
Previously stored files can be deleted either one at a  
time or all at once.  
1Load a memory card (pg. 11).  
1Load a memory card (pg. 11).  
2Set the VIDEO/DSC Switch 4 to DSC, then set  
the Power Switch y to PLAYwhile pressing down the  
Lock Button t located on the switch.  
2Set the VIDEO/DSC Switch 4 to DSC, then set  
the Power Switch y to PLAYwhile pressing down the  
Lock Button t located on the switch.  
A stored file is displayed.  
A stored file is displayed.  
3Press the MENU/VOLUME wheel % in. The Menu  
Screen appears. Rotate the MENU/VOLUME wheel %  
to select PROTECT, then press it.  
3Press the MENU/VOLUME wheel % in. The Menu  
Screen appears. Rotate the MENU/VOLUME wheel %  
to select DELETE, then press it.  
4Rotate the MENU/VOLUME wheel % to select the  
4Rotate the MENU/VOLUME wheel % to select the  
desired mode.  
desired mode.  
CURRENT : Protects the currently displayed file.  
PROT.ALL : Protects all files stored on the memory  
card.  
CURRENT : Deletes the currently displayed file.  
ALL  
: Deletes all files stored on the memory  
card.  
5Press the MENU/VOLUME wheel % in. The  
5Press the MENU/VOLUME wheel % in. The  
PROTECT Screen appears.  
DELETE Screen appears.  
If you selected CURRENTin step 4, press  
8 to select the desired file.  
2
6 or  
If you selected CURRENTin step 4, press  
8 to select the desired file.  
2
6 or  
3
3
6Rotate the MENU/VOLUME wheel % to select  
6Rotate the MENU/VOLUME wheel % to select  
EXECUTEand press it.  
EXECUTEand press it.  
To cancel protection, select RETURN.  
If the “  
mark appears, the selected file is  
protected and cannot be deleted (Protecting  
Files).  
To cancel deletion, select RETURN.  
NOTES:  
If the “  
mark appears, the currently displayed file is  
protected.  
NOTES:  
When the memory is initialised or corrupted, even  
protected files are deleted. If you do not want to lose  
important files, transfer them to a PC and save them.  
Protected files (Protecting Files) cannot be deleted  
with the above operation. To delete them, remove  
protection first.  
Once files are deleted, they cannot be restored. Check  
files before deleting.  
TO REMOVE PROTECTION  
Before doing the following, perform steps 1 through 3  
above.  
CAUTION  
4Rotate the MENU/VOLUME wheel % to select the  
Do not remove the memory card or perform any other  
operation (such as turning off the camcorder) during  
deletion. Also, be sure to use the provided AC Adapter,  
as the memory card may be corrupted if the battery  
becomes exhausted during deletion. If the memory  
card becomes corrupted, initialize it. (pg. 22)  
desired mode.  
CURRENT : Removes protection from the currently  
displayed file.  
CANC.ALL : Removes protection from all files stored  
on the memory card.  
5Press the MENU/VOLUME wheel % in. The  
Display  
PROTECT Screen appears.  
If you selected CURRENT, press  
select the desired file.  
2
6 or  
3
8 to  
Menu Screen  
MENU  
PROTECT  
DELETE  
DPOF  
6Rotate the MENU/VOLUME wheel % to select  
NO . RESET  
FORMAT  
D I SPLAY  
BR I GHT  
END  
EXECUTEand press it.  
To cancel selection, select RETURN.  
EN  
20  
ADVANCED FEATURES  
(GR-D90 and GR-D70 only)  
Dubbing Still Images Recorded On A  
Tape To A Memory Card  
Setting Print Information  
(DPOF Setting)  
Still images can be dubbed from a tape to a memory  
card.  
This camcorder is compatible with the DPOF (Digital  
Print Order Format) standard in order to support future  
systems such as automatic printing, which records  
information about the still images you wish to print  
(such as the number of prints to make). There are 2  
print information settings available: TO PRINT ALL  
STILL IMAGES (ONE PRINT FOR EACH)explained  
below and TO PRINT BY SELECTING STILL IMAGES  
AND NO. OF PRINTS.  
1Load a memory card (pg. 11) and cassette  
(pg. 9).  
2Set the VIDEO/DSC Switch 4 to VIDEO, then set  
the Power Switch y to PLAYwhile pressing down the  
Lock Button t.  
3Press the MENU/VOLUME wheel % in. The Menu  
Screen appears. Rotate it to select “  
VIDEOand  
press it.  
TO PRINT ALL STILL IMAGES  
(ONE PRINT FOR EACH)  
4Rotate the MENU/VOLUME wheel % to select  
COPYand press it. The Sub Menu  
1Set the VIDEO/DSC switch 4 to DSC, then set the  
Power Switch y to PLAY, while pressing down the  
Lock Button t located on the switch.  
appears. Rotate it to select ONand press it. Selection  
is complete.  
5Rotate the MENU/VOLUME wheel % to select  
A stored file is displayed.  
RETURNand press it twice. The normal playback  
screen reappears.  
2Press the MENU/VOLUME wheel % in. The Menu  
Screen appears.  
6To select a video image to be dubbed, start  
playback by pressing 4/6 7. At the moment you find  
the image you wish to dub, press it again to engage  
Still Playback.  
3Rotate the MENU/VOLUME wheel % to select  
DPOFand press it. The Sub Menu appears.  
4Rotate the MENU/VOLUME wheel % to select  
ALL 1and press it. Selection is complete. The DPOF  
Screen appears.  
7To start dubbing, press SNAPSHOT ^. The  
selected image is stored on the memory card.  
• “ blinks during dubbing.  
5Rotate the MENU/VOLUME wheel % to select  
EXECUTEand press it. The normal playback screen  
appears.  
NOTES:  
If SNAPSHOT ^ is pressed in step 7 when a memory  
card is not loaded, the message COPYING FAILEDis  
displayed.  
To cancel selection, rotate the MENU/VOLUME wheel  
% to select RETURNand press it.  
To change the Snapshot mode for dubbing, pg. 25.  
If an image recorded on the tape using the WIDE mode  
(pg. 29) is dubbed to a memory card, the WIDE mode  
identifying signal is not dubbed with it.  
To Reset The Setting . . .  
..... select RESETin step 4. The setting is reset to 0  
for all still images.  
To use Playback Special Effects with a video image you  
wish to dub, perform up to step 7 using the remote  
control (pg. 35).  
TO PRINT BY SELECTING STILL IMAGES AND  
NO. OF PRINTS  
Images are dubbed in 640 x 480 pixels.  
1Perform steps 1 through 3 of TO PRINT ALL STILL  
IMAGES (ONE PRINT FOR EACH).  
Display  
2Rotate the MENU/VOLUME wheel % to select  
CURRENTand press it. Selection is complete. The  
DPOF Screen appears.  
6
V I DEO  
COPY  
OFF  
ON  
3Press  
2
6 or  
3
8 so that the image you wish to  
print appears.  
4Rotate the MENU/VOLUME wheel % to move the  
highlight bar to the SHEETS number indication and  
press it.  
Menu Screen  
Continued on next page.  
EN  
21  
ADVANCED FEATURES  
(GR-D90 and GR-D70 only)  
5Select the number of prints by rotating the MENU/  
VOLUME wheel % and press it.  
Folder and File names  
Each time shooting takes place, a file name is made  
using a number which is larger by one than the  
largest number of the file names which are in use.  
Even if you delete an image file with a number in  
the middle of range, the number will not be used for  
a new shot; a gap will remain in the numerical  
sequence. If the file name reaches DVC09999, a  
new folder (such as 101JVCGR) will be made and  
the file name will start again from DVC00001.  
Repeat steps 3 through 5 for the desired number of  
prints.  
The number of prints can be set up to 15.  
To correct the number of prints, select the image  
again and change the number.  
6Rotate the MENU/VOLUME wheel % to select  
RETURNand press it. Selection is complete. SAVE?”  
appears.  
If you did not change any settings in step 3 through 5,  
the Menu Screen reappears.  
7Rotate the MENU/VOLUME wheel % to select  
EXECUTE, then press it to save the setting you have  
just made.  
Initializing A Memory Card  
You can initialize a memory card anytime.  
After initializing, all files and data stored on the  
memory card, including those which have been  
protected, are cleared.  
To cancel selection, rotate the MENU/VOLUME wheel  
% to select CANCELand press it.  
To Reset The No. Of Prints . . .  
..... select RESETin step 4 of TO PRINT ALL STILL  
IMAGES (ONE PRINT FOR EACH)on pg. 21.  
The number of prints is reset to 0 for all still  
images.  
1Perform step 1 of Making A New Folder.  
2Press the MENU/VOLUME wheel % in. The Menu  
Screen appears. Rotate the MENU/VOLUME wheel %  
to select FORMATand press it. The FORMAT Screen  
appears.  
CAUTION  
While performing the above, never disconnect power,  
as this may cause the memory to be corrupted. For  
safety, all buttons including the Power Switch y are  
disabled in step 6.  
3Rotate the MENU/VOLUME wheel % to select  
EXECUTEand press it. The memory card is  
initialized. When initialization is finished, NO IMAGES  
STOREDappears.  
To cancel initialization, rotate the MENU/VOLUME  
wheel % to select RETURNand press it.  
NOTES:  
BATTERY LOWappears if the battery remaining power  
is too low.  
If you load a memory card already set as shown above in  
a printer compatible with DPOF, it will make prints of the  
selected still images automatically.  
To print images recorded on a tape, first dub them to a  
memory card (pg. 21).  
CAUTION  
Do not perform any other operation (such as turning off  
the camcorder) during initialization. Also, be sure to use  
the provided AC Adapter, as the memory card may be  
corrupted if the battery becomes exhausted during  
initialization. If the memory card becomes corrupted  
initialize it.  
Making A New Folder  
New still pictures you are going to take can be  
separated from previously shot pictures by resetting the  
file name to DVC00001; these new pictures will be  
stored in a new folder.  
1Set the VIDEO/DSC Switch 4 to DSC, then set  
the Power Switch y to PLAYwhile pressing down the  
Lock Button t located on the switch.  
A stored file is displayed.  
2Press the MENU/VOLUME wheel % in. The Menu  
Screen appears. Rotate the MENU/VOLUME wheel %  
to select NO. RESET, then press it. The NO. RESET  
Screen appears.  
3Rotate the MENU/VOLUME wheel % to select  
EXECUTE, then press it. The new folder (such as  
101JVCGR) will be made and the file name of the  
next shot starts from DVC00001.  
EN  
22  
ADVANCED FEATURES  
(GR-D90 and GR-D70 only)  
NOTES:  
Night-Alive  
Program AE with special effects can be changed during  
recording or during Record-Standby.  
Some modes of Program AE special effects cannot be  
used during Night-Alive.  
Makes dark subjects or areas even brighter than they  
would be under good natural lighting. Although the  
recorded image is not grainy, it may look as if it is  
strobing due to the slow shutter speed.  
1Set the Power Switch y to “ ” while pressing down  
the Lock Button t located on the switch. Open the  
LCD monitor fully or pull out the viewfinder fully.  
SHUTTER  
1/60: The shutter speed is fixed at 1/60th of a second.  
Black bands that usually appear when shooting a TV  
screen become narrower.  
2Press NIGHT 0 so that the Night-Alive indicator  
* appears.  
1/100: The shutter speed is fixed at 1/100th of a  
second. The flickering that occurs when shooting under  
a fluorescent light or mercury-vapor lamp is reduced.  
• The shutter speed is automatically adjusted to provide  
up to 30 times sensitivity.  
• “A” appears beside “  
being automatically adjusted.  
* while the shutter speed is  
SPORTS  
(Variable Shutter Speed: 1/250 – 1/4000)  
To Deactivate Night-Alive . . .  
..... press NIGHT 0 again so that the Night-Alive  
indicator disappears.  
This setting allows fast-moving  
images to be captured one frame at  
a time, for vivid, stable slow-motion  
playback. The faster the shutter  
speed, the darker the picture  
NOTES:  
During Night-Alive, the following functions or settings  
cannot be activated and its indicator blinks or goes out:  
• Some modes of “Program AE With Special Effects”  
(pg. 23, 24).  
becomes. Use the shutter function  
under good lighting conditions.  
SNOW  
• “GAIN UP” in the CAMERA Menu (pg. 29).  
• “DIS” in the MANUAL Menu (pg. 29).  
During Night-Alive, it may be difficult to bring the  
camcorder into focus. To prevent this, use of manual  
focus and/or a tripod is recommended.  
Compensates for subjects that may otherwise appear  
too dark when shooting in extremely bright surround-  
ings such as in the snow.  
SPOTLIGHT  
Compensates for subjects that may otherwise appear  
too bright when shooting under extremely strong direct  
lighting such as spotlights.  
Program AE With Special Effects  
1Set the Power Switch y to “ ” while pressing down  
the Lock Button t located on the switch. Open the  
LCD monitor fully or pull out the viewfinder fully.  
NOTE:  
“SPOTLIGHT” has the same effect as –3 with the exposure  
control (pg. 26).  
2Press the MENU/VOLUME wheel % in. The Menu  
Screen appears.  
TWILIGHT  
3Rotate the MENU/VOLUME wheel % to select  
Makes evening scenes look more natural.  
PROGRAM AE”, then press it.  
White Balance (  
pg. 27) is initially set to  
, but can  
be changed to your desired setting. WhenTwilight is  
chosen, the camcorder automatically adjusts the focus  
from approx. 10 m (32 ft) to infinity. From less than 10 m  
(32 ft), adjust the focus manually.  
4Rotate the MENU/VOLUME wheel % to select the  
desired mode, then press it. Selection is complete.  
Press the MENU/VOLUME wheel % in again. The  
Menu Screen closes.  
SEPIA  
• The PROGRAM AE Menu disappears and the  
selected mode is activated. The selected mode  
indicator appears.  
Recorded scenes have a brownish tint like old photos.  
Combine this with the Cinema mode for a classic look.  
To Deactivate The Selected Mode . . .  
..... select “OFF” in step 4.  
MONOTONE  
Like black and white films, your footage is shot in B/W.  
Used together with the Cinema mode, it enhances the  
“classic film” effect.  
IMPORTANT  
Some modes of Program AE with special effects  
cannot be used with certain Fade/Wipe Effects  
(pg. 24). If an unusable mode is selected, its  
indicator blinks or goes out.  
CLASSIC FILM  
Gives recorded scenes a strobe effect.  
STROBE  
Your recording looks like a series of consecutive  
snapshots.  
EN  
23  
FOR RECORDING  
FADER WHITE  
Fade/Wipe Effects  
Fade in or out with a white screen.  
These effects let you make pro-style scene transitions.  
Use them to spice up the transition from one scene to  
the next.  
FADER BLACK  
Fade in or out with a black screen.  
Fade or Wipe works when tape recording is started or  
when you stop recording.  
FADER B.W  
Fade in to a color screen from a black and white  
screen, or fade out from color to black and white.  
1Set the VIDEO/DSC Switch 4 to VIDEO(GR-D90/  
D70 only), then set the Power Switch y to “ ” while  
pressing down the Lock Button t located on the  
switch. Open the LCD monitor fully or pull out the  
viewfinder fully.  
WIPE CORNER  
Wipe in on a black screen from the upper right to the  
lower left corner, or wipe out from lower left to upper  
right, leaving a black screen.  
2Press the MENU/VOLUME wheel % in. The Menu  
Screen appears.  
WIPE WINDOW  
The scene starts in the center of a black screen and  
wipes in toward the corners, or comes in from the  
corners, gradually wiping out to the center.  
3Rotate the MENU/VOLUME wheel % to select  
WIPE/FADER, then press it.  
4Rotate the MENU/VOLUME wheel % to select the  
desired function, then press it. Selection is complete.  
Press the MENU/VOLUME wheel % in again.  
WIPE SLIDE  
Wipe in from right to left, or wipe out from left to right.  
The WIPE/FADER Menu disappears and the effect is  
reserved. The indicator representing the selected  
effect appears.  
WIPE DOOR  
Wipe in as the two halves of a black screen open to the  
left and right, revealing the scene, or wipe out and the  
black screen reappears from left and right to cover the  
scene.  
5Press the Recording Start/Stop Button w to activate  
the Fade-in/out or Wipe-in/out.  
To Deactivate The Selected Effect . . .  
..... select OFFin step 4.  
WIPE SCROLL  
The scene wipes in from the bottom to the top of a  
black screen, or wipes out from top to bottom, leaving a  
black screen.  
IMPORTANT  
Some Fade/Wipe Effects cannot be used with certain  
modes of Program AE with special effects (pg. 23).  
If an unusable Fade/Wipe Effect is selected, its  
indicator blinks or goes out.  
WIPE SHUTTER  
Wipe in from the center of a black screen toward the  
top and bottom, or wipe out from the top and bottom  
toward the center leaving a black screen.  
NOTE:  
You can extend the length of a Fade or Wipe by pressing  
and holding the Recording Start/Stop Button w.  
^
%
w
t
y
EN  
24  
FOR RECORDING  
NOTES:  
Snapshot (For Tape Recording)  
To remove the shutter sound, BEEPon pg. 30.  
If Snapshot recording is not possible, PHOTOy blinks  
when SNAPSHOT ^ is pressed.  
This feature lets you record still images that look like  
photographs onto a tape.  
If Program AE with special effects (pg. 23) is  
engaged, certain modes of Program AE with special  
effects are disabled during Snapshot recording. In such a  
case, the icon blinks.  
SNAPSHOT MODE SELECTION  
1Set the VIDEO/DSC Switch 4 to VIDEO(GR-D90/  
D70 only), then set the Power Switch y to “ ” while  
pressing down the Lock Button t located on the  
switch. Open the LCD monitor fully or pull out the  
viewfinder fully.  
If SNAPSHOT ^ is pressed when DISis set to ON”  
(pg. 29), the Stabilizer will be disabled.  
The Motor Drive mode is disabled when REC SELECT”  
is set to “  
/
in the Menu Screen  
(pg. 31).  
If REC SELECTis set to “  
2Press the MENU/VOLUME wheel % in. The Menu  
/
in the DSC  
Screen appears.  
Menu Screen, still images are recorded on the memory  
card as well (640 x 480 pixels).  
During tape playback as well, all snapshot modes are  
3Rotate the MENU/VOLUME wheel % to select  
(CAMERA), then press it.  
available when “  
COPYis set to OFFin the  
4Rotate the MENU/VOLUME wheel % to select  
Menu Screen (pg. 31). However, the shutter sound is  
not heard.  
SNAP MODE, then press it.  
During Snapshot recording, the image displayed in the  
viewfinder may be partially missing. However, there is no  
effect in the recorded image.  
When a cable is connected to the AV connector, the  
shutter sound is not heard from the speaker, however it is  
recorded onto the tape.  
5Rotate the MENU/VOLUME wheel % to select the  
desired Snapshot mode, then press it.  
Rotate the MENU/VOLUME wheel % to select  
RETURNand press it twice. The Menu Screen  
closes.  
Auto Focus  
The camcorders Full Range AF system offers  
continuous shooting ability from close-up (as close as  
approx. 5 cm (2") to the subject) to infinity.  
FULL  
PIN-UP  
FRAME  
However, correct focus may not be obtainable in the  
situations listed below (in these cases use manual  
focusing):  
Snapshot mode  
with no frame  
Pin-Up mode  
Snapshot mode  
with frame  
There is the sound effect of a shutter closing.  
When two subjects overlap in the same scene.  
When illumination is low.*  
When the subject has no contrast (difference in  
brightness and darkness), such as a flat, one-color  
wall, or a clear, blue sky.*  
When a dark object is barely visible in the viewfinder.*  
When the scene contains minute patterns or identical  
patterns that are regularly repeated.  
When the scene is affected by sunbeams or light  
reflecting off the surface of a body of water.  
When shooting a scene with a high-contrast back-  
ground.  
SNAPSHOT RECORDING  
1Press SNAPSHOT ^. PHOTOy appears while  
the snapshot is being taken.  
If you press during Record-Standby . . .  
..... PHOTOy appears and a still image will be  
recorded for approx. 6 seconds, then the  
camcorder re-enters the Record-Standby mode.  
If you press during Recording . . .  
..... PHOTOy appears and a still image will be  
recorded for approx. 6 seconds, then the normal  
recording resumes.  
* The following low-contrast warnings appear blinking:  
,
,
and  
NOTES:  
Regardless of the Power Switch y position (“ ” or  
If the lens is smeared or blurred, accurate focusing is not  
possible. Keep the lens clean, wiping with a piece of soft  
cloth if it gets dirty. When condensation occurs, wipe with  
a soft cloth or wait for it to dry naturally.  
), Snapshot recording takes place using the  
selected Snapshot mode.  
Motor Drive Mode  
When shooting a subject close to the lens, zoom out first  
(pg. 13). If zoomed-in in the auto focus mode, the  
camcorder may automatically zoom out depending on the  
distance between the camcorder and the subject. This will  
not occur when TELE MACRO(pg. 29) is activated.  
Keeping SNAPSHOT ^ pressed provides an effect  
similar to serial photography. (Interval between still  
images: approx. 1 second)  
EN  
25  
FOR RECORDING  
Manual Focus  
To obtain correct focus.  
Exposure Control  
Manual exposure adjustment is recommended in the  
following situations:  
1If you are using the viewfinder, you should already  
have made the necessary viewfinder adjustments  
(pg. 8).  
When shooting using reverse lighting or when the  
background is too bright.  
When shooting on a reflective natural background  
such as at the beach or when skiing.  
When the background is overly dark or the subject  
light.  
2Set the Power Switch y to “ ” while pressing  
down the Lock Button t located on the switch, then  
press FOCUS * (pgs. 46 and 47). The manual  
focus indicator appears.  
1Set the Power Switch y to “ ” while pressing  
down the Lock Button t located on the switch. Open  
the LCD monitor fully or pull out the viewfinder fully.  
3To focus on a farther subject, rotate the MENU/  
VOLUME wheel % towards +. “ ” o appears and  
blinks.  
To focus on a nearer subject, rotate the MENU/  
VOLUME wheel % towards “–”. “ ” o appears and  
blinks.  
2Press the MENU/VOLUME wheel % in. The Menu  
Screen appears.  
3Rotate the MENU/VOLUME wheel % to select  
(EXPOSURE), then press it.  
4Press the MENU/VOLUME wheel % in. Focus  
adjustment is complete.  
4Rotate the MENU/VOLUME wheel % to select  
MANUAL, then press it. The Menu Screen disappears.  
The exposure control indicator appears.  
To reset to Auto Focus, press FOCUS * twice or set  
the Power Switch y to “ ”.  
If FOCUS * is pressed once, the camcorder will enter  
the focus adjustment mode again.  
5Rotate the MENU/VOLUME wheel % towards +to  
brighten the image, or towards “–” to darken the image.  
(maximum 6)  
NOTES:  
Be sure to focus the lens in the maximum telephoto  
position when you use the Manual Focus mode. If you  
focus in on a subject in the wide-angle position, sharply  
focused images cannot be obtained when zoomed up  
because the depth-of-field is reduced at longer focal  
lengths.  
6Press the MENU/VOLUME wheel % in. Exposure  
adjustment is complete.  
To Return To Automatic Exposure Control . . .  
..... select AUTOin step 4. Or, set the Power Switch  
y to “ ”.  
When the focus level cannot be adjusted any further or  
closer, “ ” or “ ” will blink.  
To Brighten The Subject Quickly . . .  
..... press BACKLIGHT !.  
) is displayed and the  
subject is brightened. If pressed again,  
)
disappears and the brightness returns to the  
previous level.  
+3 exposure has the same effect as the BACKLIGHT  
! Button.  
Using BACKLIGHT ! may cause the light around the  
subject to become too bright and the subject to  
become white.  
Focus detection zone  
Backlight compensations is also available when the  
Power Switch y is set to “ ”.  
NOTE:  
You cannot use the manual exposure control at the same  
time with backlight, spotlight (pg. 23) compensation and  
SNOW(pg. 23).  
While focusing on  
a further subject  
While focusing on  
a nearer subject  
EN  
26  
FOR RECORDING  
Iris Lock  
3Rotate the MENU/VOLUME wheel % to select  
(W.BALANCE), then press it.  
Use this function in the following situations:  
4Rotate the MENU/VOLUME wheel % to select the  
When shooting a moving subject.  
desired mode.  
When the distance to the subject changes (so its size  
in the LCD monitor or the viewfinder changes), such  
as when the subject is backing away.  
AUTO: White balance is adjusted automatically  
(factory preset).  
When shooting on a reflective natural background  
such as at the beach or when skiing.  
When shooting objects under a spotlight.  
When zooming.  
MWB: White balance is set manually.  
FINE: Outdoors on a sunny day.  
CLOUD: Outdoors on a cloudy day.  
HALOGEN: A video light or similar type of  
When the subject is close, keep the iris locked. Even  
when the subject moves away from you, the image will  
not darken or brighten.  
lighting is used.  
5Press the MENU/VOLUME wheel % in. Selection is  
complete. Press the MENU/VOLUME wheel % in  
again. The Menu Screen closes and the selected mode  
indicator except AUTOappears.  
Before the following steps, perform steps 1 through  
4 of Exposure Control(pg. 26).  
5Adjust zoom so that the subject fills the LCD monitor  
or the viewfinder, then press and hold the MENU/  
VOLUME wheel % for over 2 seconds. The exposure  
control indicator ) and “ ” w appear. Press the  
To Return To Automatic White Balance . . .  
..... select AUTOin step 4. Or, set the Power Switch  
y to “ ”.  
NOTE:  
MENU/VOLUME wheel % in. “ ” w changes to “  
and the iris is locked.  
White balance cannot be used when Sepia or Monotone  
(pg. 23) is activated.  
To Return To Automatic Iris Control . . .  
..... rotate the MENU/VOLUME wheel % to display  
AUTOthen press it in step 4. The exposure  
Manual White Balance Operation  
control indicator ) and “ ” w disappear. Or, set  
the Power Switch y to “ ”.  
Perform Manual White Balance when shooting under  
various types of lighting.  
To Lock The Exposure Control And The Iris . . .  
..... after step 4 of Exposure Control(pg. 26),  
adjust the exposure rotating the MENU/VOLUME  
wheel %. Then lock the iris in step 5 of Iris Lock.  
For automatic locking, rotate the MENU/VOLUME  
wheel % to select AUTO, then press it in step 4.  
The iris becomes automatic after about 2 seconds.  
1Follow steps 1 through 4 of the white balance  
adjustment, and select “  
MWB.  
2Hold a sheet of plain white paper in front of the lens.  
Adjust zoom or position yourself so that the white paper  
fills the screen.  
Iris  
3Press the MENU/VOLUME wheel % in until  
Like the pupil of the human eye, it contracts in well-lit  
environments to keep too much light from entering, and  
dilates in dim environments to allow in more light.  
begins blinking rapidly.  
When the setting is completed,  
blinking.  
resumes normal  
4Press the MENU/VOLUME wheel % in twice. The  
Menu Screen closes and the Manual White Balance  
White Balance Adjustment  
indicator  
( is displayed.  
A term that refers to the correctness of color reproduc-  
tion under various lighting. If the white balance is  
correct, all other colors will be accurately reproduced.  
The white balance is usually adjusted automatically.  
However, more advanced camcorder operators control  
this function manually to achieve a more professional  
color/tint reproduction.  
NOTES:  
In step 2, it may be difficult to focus on the white paper. In  
such a case, adjust focus manually (pg. 26).  
A subject can be shot under various types of lighting  
conditions indoors (natural, flourescent, candlelight, etc.).  
Because the color temperature is different depending on  
the light source, the subject tint will differ depending on  
the white balance settings. Use this function for a more  
natural result.  
1Set the Power Switch y to “ ” while pressing  
down the Lock Button t located on the switch. Open  
the LCD monitor fully or pull out the viewfinder fully.  
Once you adjust white balance manually, the setting is  
retained even if the power is turned off or the battery  
removed.  
2Press the MENU/VOLUME wheel % in. The Menu  
Screen appears.  
EN  
27  
FOR RECORDING  
WIPE/FADER  
Refer to Fade/Wipe Effects(pg. 24).  
PROGRAM AE  
For Recording Menu  
This camcorder is equipped with an easy-to-use,  
on-screen menu system that simplifies many of the  
more detailed camcorder settings (pg. 28 31).  
Refer to Program AE With Special Effects(pg. 23).  
EXPOSURE  
1Set the Power Switch y to “ ” while pressing  
down the Lock Button t located on the switch. Open  
the LCD monitor fully or pull out the viewfinder fully.  
Refer to Exposure Controland Iris Lock(pg. 26,  
27).  
2Press the MENU/VOLUME wheel % in. The Menu  
Screen appears.  
W.BALANCE  
3Rotate the MENU/VOLUME wheel % to select the  
desired function menu, and press it.  
Refer to White Balance Adjustmentand Manual  
White Balance Operation(pg. 27).  
4Function menu setting depends on the function.  
CAMERA  
If you have selected “  
WIPE/FADER,  
PROGRAM AE, “  
W. BALANCE. . .  
EXPOSUREor  
Settings made in the “  
effective whether the Power Switch y is set to “ ” or  
. However, the menu settings can be changed only  
CAMERAMenu remain  
..... see the column on the right.  
If you have selected CAMERA, “  
CAMERA DISPLAYor  
MANUAL,  
when the Power Switch y is set to “ ”.  
SYSTEM, “  
DSC. . .  
CAMERA  
REC MODE  
..... go to step 5.  
SOUND MODE12B I T  
ZOOM  
SNAP MODE  
GA I N UP  
40X  
5Rotate the MENU/VOLUME wheel % to select the  
desired function and press it. The Sub Menu appears.  
Then, rotate the MENU/VOLUME wheel % to select  
the parameter, and press it. Selection is complete.  
FULL  
AGC  
6Rotate the MENU/VOLUME wheel % to select  
RETURN  
RETURNand press it twice. The Menu Screen  
closes.  
REC MODE  
The  
icon represents END.  
Allows you to set the tape recording mode ([SP] or LP)  
NOTE:  
depending on your preference (pg. 10).  
When the Menu Screen is left on for a couple of minutes, a  
residual image may be left on the screen and it may take  
several seconds for the residual image to disappear. This is  
not due to any defect of the unit.  
SOUND MODE  
[12BIT]: Enables tape recording of stereo sound on  
four separate channels, and is recommended for use  
when performing audio dubbing. (Equivalent to the  
32 kHz mode of previous models)  
16BIT: Enables tape recording of stereo sound on  
two separate channels. (Equivalent to the 48 kHz  
mode of previous models)  
ZOOM  
16X: When set to 16Xwhile using digital zoom, the  
zoom magnification will reset to 16X since digital  
zoom will be disengaged.  
[40X]: Allows you to use the Digital Zoom. By digitally  
processing and magnifying images, zooming is  
possible from 16X (the optical zoom limit), to a  
maximum of 40X digital magnification.  
700X: Allows you to use the Digital Zoom. By digitally  
processing and magnifying images, zooming is  
possible from 16X (the optical zoom limit), to a  
maximum of 700X digital magnification.  
SNAP MODE  
Refer to Snapshot (For Tape Recording)(pg. 25).  
[ ] = Factory-preset  
EN  
28  
USING MENUS FOR DETAILED ADJUSTMENT  
GAIN UP  
WIDE MODE  
OFF: Allows you to shoot dark scenes with no picture  
brightness adjustment.  
[OFF]: Records with no change in the screen ratio.  
For playback on a TV with a normal screen ratio.  
[AGC]: The overall appearance may be grainy, but the  
image is bright.  
CINEMA  
: Inserts black bands at the top and  
bottom of the screen. During playback on  
wide-screen TVs, the black bands at the top and  
bottom of the screen are cut and the screen ratio  
AUTO  
: The shutter speed is automatically  
adjusted (1/30 1/200 sec.). Shooting a subject in  
low or poor lighting at 1/30 sec. shutter speed  
provides a brighter image than in the AGC mode, but  
the subjects movements are not smooth or natural.  
The overall appearance may be grainy. While the  
shutter speed is being automatically adjusted, “  
is displayed.  
becomes 16:9.  
2 appears. When using this  
mode, refer to your wide-screen TVs instruction  
manual. During playback/recording on 4:3 TVs/LCD  
monitor/viewfinder, black bands are inserted at the  
top and bottom of the screen and the image appears  
like a letterboxed 16:9 movie.  
The CINEMAmode is effective only when the  
VIDEO/DSC Switch 4 is set to VIDEO(GR-D90/  
D70 only).  
MANUAL  
The “  
MANUALsettings are effective only when the  
Power Switch y is set to “ ”.  
SQUEEZE  
ratio of 16:9. Naturally expands the image to fit the  
screen without distortion.  
using this mode, refer to your wide-screen TVs  
instruction manual. During playback/recording on 4:3  
TVs/LCD monitor/viewfinder, the image is elongated  
vertically.  
: For playback on TVs with an aspect  
2 appears. When  
MANUAL  
D I S  
ON  
TELE MACROOFF  
WI DE MODE  
WI ND CUT  
OFF  
OFF  
The SQUEEZEmode is effective only when the  
VIDEO/DSC Switch 4 is set to VIDEO(GR-D90/  
D70 only).  
RETURN  
WIND CUT  
DIS  
OFF: To turn off this function.  
[OFF]: Disengages the function which cuts down on  
noise created by wind.  
[ON  
]: To compensate for unstable images caused  
ON  
: Helps cut down on noise created by wind.  
7 appears. The quality of the sound will  
by camera-shake, particularly at high magnification.  
change. This is normal.  
NOTES:  
Accurate stabilization may not be possible if hand shake  
is excessive, or under the following conditions:  
When shooting subjects with vertical or horizontal  
stripes.  
When shooting dark or dim subjects.  
When shooting subjects with excessive backlighting.  
When shooting scenes with movement in various  
directions.  
SYSTEM  
SYSTEMfunctions which are set when the Power  
Switch y is set to “ ” are also applied when the  
Power Switch y is set to PLAY(pg. 31).  
SYSTEM  
BEEP  
MELODY  
ON  
TALLY  
When shooting scenes with low-contrast backgrounds.  
Switch off this mode when recording with the camcorder  
on a tripod.  
REMOTE  
ON  
DEMO MODE  
PR I OR I TY  
CAM RESET  
ON  
LCD  
The “  
cannot be used.  
indicator ! blinks or goes out if the Stabilizer  
TELE MACRO  
RETURN  
[OFF]: To turn off this function.  
ON: Usually the distance to a subject where the lens  
is in focus depends on the zoom magnification.  
Unless there is a distance more than 1m (3.3 ft.) to  
the subject, the lens is out of focus at the maximum  
telephoto setting. When set to ON, you can shoot a  
subject as large as possible at a distance of approx.  
60 cm (2 ft.).  
[ ] = Factory-preset  
Depending on the zoom position, the lens may go  
out of focus.  
EN  
29  
USING MENUS FOR DETAILED ADJUSTMENT  
BEEP  
CAM RESET  
OFF: Even though not heard while shooting, shutter  
sound is recorded on the tape.  
[CANCEL]: Does not reset all settings to the  
factory-preset.  
BEEP: The beep sounds when the power is turned on  
or off, and at the beginning and end of recording. Also  
to activate the shutter sound effect (pg. 17, 25).  
EXECUTE: Resets all settings to the factory-preset.  
CAMERA DISPLAY  
Settings made in the “  
are effective only for video shooting.  
Settings made in the “  
CAMERA DISPLAYMenu  
[MELODY]: Instead of a beep, a melody sounds  
when any operation is performed. It also activates the  
shutter sound effect (pg. 17, 25).  
CAMERA DISPLAYMenu  
remain effective even when the Power Switch y is set  
to “ ”. However, the menu settings can be changed  
only when the Power Switch y is set to “ ”.  
TALLY  
OFF: The tally lamp remains off at all times.  
[ON]: The tally lamp comes on to signal the start of  
recording.  
CAMERA D I SPLAY  
BR I GHT  
ON SCREEN  
DATE / T I ME  
T I ME CODE  
CLOCK  
LCD / TV  
AUTO  
REMOTE  
OFF  
OFF: Disables the camcorder from receiving the  
remote control's beam signals. The camcorder cannot  
be operated by the remote control.  
DEC 25 03  
5 : 30 PM  
ADJ .  
[ON]: Enables the camcorder to receive the remote  
controls beam signals.  
RETURN  
For GR-D30 Owners: It is recommended that this  
function be set to OFFto prevent improper  
operation.  
BRIGHT  
pg. 12, To Adjust The Brightness Of The Display”  
DEMO MODE  
ON SCREEN  
OFF: Automatic demonstration will not take place.  
LCD: Keeps the camcorders display (except the date,  
time and time code) from appearing on the connected  
TV screen.  
[ON]: Demonstrates certain functions such as  
Program AE with special effects, etc., and can be  
used to confirm how these functions operate.  
Demonstration starts in the following cases:  
[LCD/TV]: Makes the camcorders display appear on  
screen when the camcorder is connected to a TV.  
When the Menu Screen is closed after DEMO  
MODEis turned ON.  
With DEMO MODEset to ON, if there is no  
operation for about 3 minutes after the Power Switch  
y is set to “ ” or “ ” .  
DATE/TIME  
OFF: The date/time does not appear.  
[AUTO]: Displays the date/time for approx. 5 seconds  
in the following cases:  
When the Power Switch y is set from OFF  
(CHARGE)to “ ” or “ ”.  
When tape playback starts. The camcorder displays  
the date/time when scenes are recorded.  
When the date is changed during tape playback.  
Performing any operation during the demonstration  
stops the demonstration temporarily. If no operation is  
performed for more than 3 minutes after that, the  
demonstration will resume.  
NOTES:  
ON: The date/time is always displayed.  
If a tape is in the camcorder, the demonstration cannot be  
turned on.  
The date indication can also be turned on/off by  
pressing the DISPLAY Button l on the remote  
control (provided with GR-D90/D70 only).  
DEMO MODEremains ONeven if the camcorder  
power is turned off.  
If DEMO MODEremains ON, some functions will not  
be available. After viewing demo, set to OFF.  
TIME CODE  
[OFF]: Time code is not displayed.  
PRIORITY  
ON: Time code is displayed on the camcorder and on  
the connected TV. Frame numbers are not displayed  
during recording.  
[LCD]: When the LCD monitor is fully open, even if  
the viewfinder is pulled out, the image is displayed  
only on the LCD monitor; it will not be displayed in the  
viewfinder.  
[ ] = Factory-preset  
FINDER: When the viewfinder is pulled out, even if  
the LCD monitor is fully open, the image is displayed  
only on the viewfinder; it will not be displayed on the  
LCD monitor.  
EN  
30  
USING MENUS FOR DETAILED ADJUSTMENT  
VIDEO  
CLOCK ADJ.  
Allows you to set the current date and time (pg. 10).  
V I DEO  
SOUND MODE  
STEREO  
DSC (GR-D90/D70 only)  
12B I T MODE  
REC MODE  
COPY  
SOUND  
1
OFF  
OFF  
DSC  
S / AV I NPUT  
QUAL I TY  
F I NE  
I MAGE S I ZE1024X768  
REC SELECT–  
RETURN  
SOUND MODE  
12BIT MODE  
REC MODE  
........pg. 32, Playback Sound.  
RETURN  
........pg. 32, Display.  
QUALITY  
,
IMAGE SIZE  
Allows you to set the tape recording mode ([SP] or  
LP) depending on your preference (pg. 10).  
It is recommended you use REC MODEin the  
Refer to Picture Quality/Image Size Setting”  
(pg. 11).  
REC SELECT  
VIDEOMenu when using this camcorder as a  
recorder during dubbing (pg. 33, 34).  
[
]: When Snapshot recording is performed  
with the VIDEO/DSC Switch 4 set to VIDEO, still  
images are recorded only onto the tape.  
• “REC MODEcan be set when the Power Switch y is  
set to PLAYor “ ” (pg. 10, 28).  
/
: When Snapshot recording is  
COPY (GR-D90/D70 only)  
performed with the VIDEO/DSC Switch 4 set to  
VIDEO, still images are recorded not only onto the  
tape but also on the memory card (640 x 480 pixels).  
In this mode, the SNAP MODEselection in the  
CAMERA Menu is also applicable to memory card  
recording.  
ON: Enables dubbing of images recorded on a tape  
to a memory card (pg. 21).  
[OFF]: Enables snapshots to be taken during tape  
playback.  
S/AV INPUT (GR-D90/D70 only)  
ON: Enables audio/video signal input from the AV and  
S-VIDEO connectors (pg. 33).  
For Playback Menu  
[OFF]: Enables audio/video signal output to a TV,  
VCR, etc. via the AV and S-VIDEO connectors  
(pg. 16, 33).  
When S/AV INPUTis set to ON, camcorder  
playback cannot be viewed on the AV output.  
1Set the VIDEO/DSC Switch 4 to VIDEO(GR-D90/  
D70 only), then set the Power Switch y to PLAY”  
while pressing down the Lock Button t located on the  
switch.  
2Press the MENU/VOLUME wheel % in. The Menu  
SYSTEM  
Screen appears.  
3Rotate the MENU/VOLUME wheel % to select the  
SYSTEM  
desired function menu, and press it.  
BEEP  
MELODY  
ON  
TALLY  
4Rotate the MENU/VOLUME wheel % to select the  
REMOTE  
ON  
DEMO MODE  
PR I OR I TY  
CAM RESET  
ON  
desired function, and press it to display the Sub Menu.  
LCD  
5Rotate the MENU/VOLUME wheel % to select the  
desired parameter and press it. Selection is complete.  
RETURN  
6Rotate the MENU/VOLUME wheel % to select  
RETURNand press it twice to close the Menu  
Screen.  
Each setting is linked with “  
SYSTEM, which  
appears when the Power Switch y is set to “  
(pg. 30).  
The parameters are the same as in the description on  
pg. 30.  
[ ] = Factory-preset  
EN  
31  
USING MENUS FOR DETAILED ADJUSTMENT  
VIDEO DISPLAY  
Settings made in the VIDEO DISPLAYMenu are  
effective only for tape playback.  
NOTES:  
For GR-D90/D70 Owners: You can also use the provided  
remote controls AUDIO button T to change the output  
sound (without having to access the Playback Menu).  
Make sure you point the remote control at the  
camcorders remote sensor 1.  
V I DEO D I SPLAY  
BR I GHT  
ON SC  
DATE / T I ME  
T I M COD  
R
EEN  
LCD  
The camcorder cannot detect the sound mode in which  
the recording was made during fast-forward or rewind.  
During playback the sound mode is displayed in the upper  
left corner.  
O
FF  
E
E
OFF  
The SOUND MODEsetting is available for both  
12-bit and 16-bit sound. (In previous modelsfunctions,  
12-bitis called 32 kHzand 16-bitis called 48 kHz.)  
RETURN  
Display  
BRIGHT  
,
DATE/TIME  
,
TIME CODE  
Refer to “  
CAMERA DISPLAYon page 30, 31.  
The factory-preset of DATE/TIMEin the “  
VIDEO  
4
6
12b i  
L
t
/ SOUND  
1
ON SCREEN setting:  
For playback sound,  
tape speed and tape  
running.  
DISPLAYMenu is OFF.  
ON SCREEN  
OFF: Camcorder's display (except the date, time and  
time code) is not shown on LCD or connected TV.  
[LCD]: Camcorder's display is shown only on LCD  
and not on connected TV (except the date, time and  
time code).  
LCD/TV: Camcorder's display is shown on both LCD  
and connected TV.  
DATE/TIME setting:  
For date/time.  
Playback Sound  
DEC 25 03  
5 : 30 PM  
During tape playback, the camcorder detects the sound  
mode in which the recording was made, and plays the  
sound back. Select the type of sound to accompany  
your playback picture. According to the menu access  
explanation on pg. 31, select SOUND MODEor  
12BIT MODEfrom the Menu Screen and set it to the  
desired parameter.  
TIME CODE setting:  
For time code.  
Minutes  
Seconds  
Frames*  
12 : 34 : 24  
SOUND MODE  
[STEREO  
]: Sound is output on both Land R”  
* 30 frames = 1 second  
channels in stereo.  
SOUND L : Sound from the Lchannel is output.  
SOUND R : Sound from the Rchannel is output.  
12BIT MODE  
MIX: Original and dubbed sounds are combined and  
output in stereo on both Land Rchannels.  
[SOUND 1]: Original sound is output on both Land  
Rchannels in stereo.  
SOUND 2: Dubbed sound is output on both Land  
Rchannels in stereo.  
[ ] = Factory-preset  
EN  
32  
USING MENUS FOR DETAILED ADJUSTMENT  
For GR-D90/D70 Owners:  
To Use This Camcorder As A Recorder  
Dubbing To Or From A VCR  
To Use This Camcorder As A Player  
1. Set the VIDEO/DSC Switch 4 to VIDEO, then set  
the camcorders Power Switch y to PLAYwhile  
pressing down the Lock Button t located on the  
switch.  
1Following the illustration, connect the camcorder  
and the VCR. Also refer to pg. 16.  
2Set the VIDEO/DSC Switch 4 to VIDEO(GR-D90/  
D70 only), then set the camcorders Power Switch y to  
PLAYwhile pressing down the Lock Button t located  
on the switch, turn on the VCRs power, and insert the  
appropriate cassettes in the camcorder and the VCR.  
2. Set S/AV INPUTto ONand set REC MODEto  
SPor LP(pg. 31).  
3. Connect the cables as shown in the illustration and  
load a cassette to record on.  
4. Press the Recording Start/Stop button w to  
3Engage the VCRs AUX and Record-Pause modes.  
AV. IN  
engage the Record-Pause mode. “  
appears  
on the screen.  
4Engage the camcorders Play mode to find a spot  
just before the edit-in point. Once it is reached, press  
4/6 7 on the camcorder.  
5. Press the Recording Start/Stop button w to start  
recording. 3 rotates.  
6. Press the Recording Start/Stop button w again to  
5Press 4/6 7 on the camcorder and engage the  
engage the Record-Pause mode.  
rotating.  
3 stops  
VCRs Record mode.  
6Engage the VCRs Record-Pause mode and press  
4/6 7 on the camcorder.  
NOTES:  
After dubbing, set S/AV INPUTback to OFF.  
Analog signals can be converted to digital signals with  
this procedure.  
7Repeat steps 4 through 6 for additional editing, then  
stop the VCR and camcorder when finished.  
It is also possible to dub from another camcorder.  
NOTES:  
As the camcorder starts to play your footage it will appear  
on your TV. This will confirm the connections and the AUX  
channel for dubbing purposes.  
Before you start dubbing, make sure that the indications  
do not appear on the connected TV. If they do, they are  
being recorded onto the new tape.  
7
4
To choose whether or not the following displays  
appear on the connected TV . . .  
To AV (  
Date/Time  
..... set DATE/TIMEto AUTO, ONor OFFin the  
Menu Screen (pg. 30, 32).  
Connector  
cover*  
Or, press DISPLAY l on the remote control  
(provided with GR-D90/D70 only) to turn on/off the  
date indication.  
Audio/  
Video cable  
Time Code  
(provided)  
To  
..... set TIME CODEto ONor OFFin the Menu  
Screen (pg. 31, 32).  
S-VIDEO )  
Indications other than date/time and time code  
..... set ON SCREENto LCD, LCD/TVor OFFin  
the Menu Screen (pg. 30, 32).  
Yellow to VIDEO**  
IN or OUT  
S-Video cable  
(optional)  
Red to AUDIO  
R IN or OUT  
White to  
AUDIO L  
IN or OUT  
To S-VIDEO  
IN or OUT  
TV  
VCR  
* When connecting the cable, open this cover.  
** Connect when an S-Video cable is not used.  
EN  
33  
DUBBING  
5. Press the Recording Start/Stop button w to start  
recording. 3 rotates.  
Dubbing To Or From A Video Unit  
Equipped With A DV Connector  
(Digital Dubbing)  
6. Press the Recording Start/Stop button w again to  
engage the Record-Pause mode.  
rotating.  
3 stops  
It is also possible to copy recorded scenes from this  
camcorder onto another video unit equipped with a DV  
connector. Since a digital signal is sent, there is little if  
any image or sound deterioration.  
NOTES:  
Digital Dubbing is performed in the sound mode recorded  
on the original tape, regardless of the current SOUND  
MODEsetting (pg. 28).  
To Use This Camcorder As A Player  
During Digital Dubbing, incoming signals cannot be  
output through the video or audio connectors if they are  
copy-guarded.  
1Make sure all units are turned off. Connect this  
camcorder to a video unit equipped with a DV input  
connector using a DV cable as shown in the illustration.  
2Set this camcorders VIDEO/DSC Switch 4 to  
VIDEO(GR-D90/D70 only), then the Power Switch y  
to PLAYwhile pressing down the Lock Button t  
located on the switch, turn on the video units power,  
and insert the appropriate cassettes in this camcorder  
and the video unit.  
4
7
w
3Press  
4
7 to play back the source tape.  
4While watching the playback on the monitor, engage  
the DV connector-equipped video units record mode  
from the spot on the source tape you want to begin  
recording.  
To DV @  
NOTES:  
t
(
)
CHARGE  
Core filter  
OFF  
PLAY  
It is recommended to use the AC Adapter as the  
power supply instead of the battery pack (pg. 7).  
If the remote control is used when both the player and  
recorder are JVC video units, both units will perform the  
same operation. To prevent this from happening, press  
the buttons on both units.  
DV cable  
(optional)  
y
Core filter  
If a blank portion or disturbed image is played back on  
the player during dubbing, the dubbing may stop so that  
an unusual image is not dubbed.  
To DV  
IN/OUT  
Even though the DV cable is connected correctly,  
sometimes the image may not appear in step 4. If this  
occurs, turn off the power and make connections again.  
If Playback Zoom(pg. 14, 35), Playback Special  
Effects(GR-D90/D70 only, pg. 35) or Snapshotis  
attempted during playback, only the original playback  
image recorded on the tape is output from the DV  
connector @.  
Video unit equipped  
with DV connector  
When using a DV cable, be sure to use the optional  
JVC VC-VDV204U DV cable.  
To Use This Camcorder As A Recorder  
1. Set this camcorders VIDEO/DSC Switch 4  
(GR-D90/D70 only) to VIDEO, then the Power  
Switch y to PLAYwhile pressing down the Lock  
Button t located on the switch.  
2. Set REC MODEto SPor LPin the Menu  
Screen (pg. 31).  
3. Connect the DV cable as shown in the illustration  
and load a cassette to record on.  
4. Press the Recording Start/Stop button w to  
DV. IN  
engage the Record-Pause mode. “  
appears  
on the screen.  
EN  
34  
DUBBING  
Playback Special Effects  
Make sure “REMOTE” in the SYSTEM Menu is set  
to “ON” (pg. 30) and the remote control is  
pointed at the remote sensor 1. The transmitted  
beam’s approximate effective distance for indoor  
use is 5m (16ft).  
To allow you to add creative effects to the playback  
image.  
1To start playback, press PLAY (4) j.  
2Point the remote control at the camcorder’s remote  
sensor and press EFFECT f. The PLAYBACK  
EFFECT Select Menu appears.  
Slow-Motion Playback  
To allow slow-speed search in either direction during  
tape playback.  
3Move the highlight bar to the desired effect by  
pressing EFFECT f. The selected function is activated  
and after 2 seconds the menu disappears.  
1To change from normal to Slow-Motion Playback,  
press SLOW (9) U or (0) g more than approx. 2  
seconds. After approx. 5 minutes (approx. 20 seconds  
with an 80-minute cassette) in Slow Rewind or approx.  
5 minutes in Slow Forward, normal playback resumes.  
To deactivate the selected effect, press ON/OFF d  
on the remote control. Pressing it again re-activates  
the selected effect.  
To change the selected effect, repeat from step 2  
above.  
To stop Slow-Motion Playback, press PLAY (4) j.  
NOTE:  
NOTES:  
The effects that can be used during playback are Classic  
Film, Monotone, Sepia and Strobe. The effects work the  
same in playback as they did in recording. Refer to page  
23, 24 for more information.  
You can also engage Slow-Motion Playback from Still  
Playback by pressing SLOW U g more than approx.  
2 seconds.  
During Slow-Motion Playback, due to digital image  
processing, the picture may take on a mosaic effect.  
After SLOW (9) U or (0) g is pressed and held, the still  
image may be displayed for a few seconds, followed by a  
blue screen for a few seconds. This is not a malfunction.  
There may be a small margin between the slow-motion  
playback start point you chose and the actual start point  
for Slow-Motion Playback.  
During Slow-Motion Playback, there will be disturbances  
in video and the picture may seem unstable, especially  
with steady images. This is not a malfunction.  
During Slow-Motion Playback, press PAUSE (6) Y to  
pause playback.  
Playback Zoom  
To magnify the recorded image up to 44X at any time  
during playback.  
1Press PLAY (4) j to find the scene of interest.  
2Press the Zoom Button T ; or W A on the remote  
control. Make sure the remote control is pointed at the  
camcorder's remote sensor. Pressing T ; zooms in.  
3You can move the image on screen around to find a  
particular portion of the picture. While holding down  
E
SHIFT a, press  
*
(Left) I, T(Right) h,  
^
(Up) Y  
and (Down) P.  
&
R
Y
I
s
f
h
d
g
j
To end zoom, press and hold W A until magnification  
returns to normal. Or, press STOP (5) P and then  
press PLAY (4) j.  
T
U
O
a
k
;
NOTES:  
P
l
A
Zoom can also be used during slow-motion and still  
playback.  
Due to ditital image processing, the quality of the image  
may suffer.  
Frame-By-Frame Playback  
Press T ;  
Normal playback  
To allow frame-by-frame search during tape playback.  
1To change from normal to Frame-By-Frame  
Playback, press SLOW (0) g repeatedly for forward or  
SLOW (9) U repeatedly for reverse. Each time it is  
pressed, the frame is played back.  
To move image, press  
T
NOTE:  
(Right) h while keeping  
SHIFT a held down.  
You can also engage Frame-By-Frame Playback from Still  
Playback by pressing SLOW (9) U or (0) g repeatedly.  
EN  
35  
USING THE REMOTE CONTROL UNIT  
(GR-D90 and GR-D70 only)  
Audio Dubbing  
Insert Editing  
The audio track can be customized only when recorded  
in the 12-bit mode (pg. 28).  
You can record a new scene into a previously recorded  
tape, replacing a section of the original recording with  
minimal picture distortion at the in and outpoints. The  
original audio remains unchanged.  
NOTES:  
Audio Dubbing is not possible on a tape recorded in  
16-bit audio, on a tape recorded in the LP mode or on a  
blank portion of a tape.  
NOTES:  
Before performing the following steps, make sure that  
TIME CODEis set to ONin the Menu Screen  
(pg. 31, 32).  
To perform Audio Dubbing while watching on the  
television, make connections (pg. 16).  
Insert Editing is not possible on a tape recorded in the LP  
mode or on a blank portion of a tape.  
To perform Insert Editing while watching in the television,  
make connections (pg. 16).  
1Play back the tape to locate the point where editing  
will start, then press PAUSE (6) Y.  
2While holding A.DUB (e) k on the remote control,  
press PAUSE (6) Y. 6eE and MIC(GR-D90/D70  
only) appear.  
1Play back the tape, locate the Edit-Out point and  
press PAUSE (6) Y. Confirm the time code at this  
point (pg. 31, 32).  
3Press PLAY (4) j, then begin narrating.  
Speak into the microphone.  
2Press REW (2) I until the Edit-In point is located,  
then press PAUSE (6) Y.  
To pause dubbing, press PAUSE (6) Y.  
3Press and hold INSERT (w) O on the remote  
control, then press PAUSE (6) Y. 6w8 and the  
Time Code (min.:sec.) appear and the camcorder  
enters Insert-Pause mode.  
4To end Audio Dubbing, press PAUSE (6) Y, then  
STOP (5) P.  
To hear the dubbed sound during playback . . .  
..... set 12BIT MODEto SOUND 2or MIXin the  
Menu Screen (pg. 32).  
4Press START/STOP s to begin editing.  
Confirm the insert at the time code you checked in  
step 1.  
NOTES:  
Sound is not heard from the speaker during Audio  
Dubbing.  
To pause editing, press START/STOP s. Press it  
again to resume editing.  
When editing onto a tape that was recorded at 12-bit, the  
old and new soundtracks are recorded separately.  
If you dub onto a blank space on the tape, the sound may  
be disrupted. Make sure you only edit recorded areas.  
If feedback or howling occurs during TV playback, move  
the camcorders microphone away from the TV, or turn  
down the TVs volume.  
If you change from 12-bit to 16-bit in mid-recording and  
then use the tape for Audio Dubbing, it is not effective  
from the point where 16-bit recording began.  
During Audio Dubbing, when the tape moves to scenes  
recorded in the LP mode, scenes recorded in 16-bit audio  
or a blank portion, Audio Dubbing stops (pg. 50).  
To perform Audio Dubbing with a video unit connected to  
the camcorders AV connector, first set S/AV INPUTto  
ONin the Menu Screen (pg. 31). AUXappears  
instead of MIC.  
5To end Insert Editing, press START/STOP s, then  
STOP (5) P.  
NOTES:  
Program AE with special effects (pg. 23) can be used  
to spice up the scenes being edited during Insert Editing.  
During Insert Editing, the date and time information  
changes.  
If you perform Insert Editing onto a blank space on the  
tape, the audio and video may be disrupted. Make sure  
you only edit recorded areas.  
During Insert Editing, when the tape moves to scenes  
recorded in the LP mode or a blank portion, Insert Edting  
stops (pg. 50).  
E
R
Y
I
s
f
h
d
g
j
T
U
O
a
k
;
P
l
A
Stereo microphone  
EN  
36  
USING THE REMOTE CONTROL UNIT  
(GR-D90 and GR-D70 only)  
Connection To A Personal Computer  
[A] Using USB cable  
(GR-D90/D70 only)  
[B] Using DV cable  
[A] Using USB cable (GR-D90/D70 only)  
This camcorder can transfer still images to a PC via  
USB connection.  
y
(
)
CHARGE  
OFF  
PLAY  
4
[B] Using DV cable  
It is also possible to transfer still images to a PC with a  
DV connector by using software equipped with the PC  
or commercially available software.  
1Make sure the camcorder and PC are turned off.  
2Connect the camcorder to your PC using the  
appropriate cable as shown in the illustration.  
3For GR-D90/D70 Owners: If you are using the USB  
To DV @  
To USB 9  
connection, set the VIDEO/DSC switch 4 to DSC.  
4Turn the camcorders Power Switch y to PLAY”  
while pressing down the Lock Button t located on the  
switch and turn on the PC.  
Core filter  
OR  
DV cable  
(optional)  
USB cable  
(provided)  
Refer to the instruction manual of the software on how  
to transfer a still image to the PC.  
Core filter  
5When finished, turn off the PC first, then the  
camcorder.  
To USB  
connector  
To DV  
connector  
NOTES:  
Refer to SOFTWARE INSTALLATION AND USB  
CONNECTION GUIDEfor the installation of the bundled  
software and drivers.  
It is recommended to use the AC Adapter as the  
power supply instead of the battery pack (pg. 7).  
Never connect the USB cable and the DV cable  
simultaneously to the camcorder. Connect only the  
cable you wish to use to the camcorder.  
If the PC connected to the camcorder via the USB cable  
is not powered, the camcorder does not enter the USB  
mode.  
PC  
PC with DV  
connector  
The date/time information cannot be captured into the  
PC.  
Refer to the instruction manuals of the PC and Software.  
The still images can also be transferred to a PC with a DV  
connector-equipped capture board.  
When using a DV cable, be sure to use the optional  
JVC VC-VDV206U or VC-VDV204U DV cable depend-  
ing on the type of DV connector (4 or 6 pins) on the  
PC, or use the DV cable provided with the capture  
board.  
The system may not work properly depending on the PC  
or capture board you are using.  
When using the DV connection refer to manufacturer  
instructions of your capture board for drivers installation  
and operation instructions.  
ACCESSING FILESappears on the LCD monitor  
while the PC is accessing data in the camcorder or the  
camcorder is transferring a file to the PC.  
NEVER disconnect the USB cable while  
“ACCESSING FILES” is displayed on the LCD  
monitor since this can result in product damage.  
EN  
37  
SYSTEM CONNECTIONS  
Before consulting your JVC dealer, please check the  
following to see if you can correct the problem yourself.  
The focus does not adjust automatically.  
• Focus is set to the Manual mode.  
¥ Set Focus to the Auto mode (pg. 26).  
• The recording was done in a dark place, or the  
contrast was low.  
• The lens is dirty or covered with condensation.  
¥ Clean the lens and check the focus again  
The camcorder is a microcomputer-controlled  
device. External noise and interference (from a TV,  
a radio, etc.) might prevent it from functioning  
properly. In such cases, first disconnect its power  
supply unit (battery pack, AC Adapter, etc.) and wait  
a few minutes; and then re-connect it and proceed  
as usual from the beginning.  
(pg. 43).  
The cassette will not load properly.  
• The cassette is in the wrong position.  
¥ Set it in the right position (pg. 9).  
• The battery’s charge is low.  
No power is supplied.  
• The power is not connected properly.  
¥ Connect the AC Adapter securely (pg. 7).  
• The battery is dead.  
¥ Install a fully charged battery (pg. 7, 8).  
The memory card will not load properly.  
¥ Replace the dead battery with a fully charged one  
(pg. 7, 8).  
• The memory card is in the wrong position.  
¥ Set it in the right position (pg. 11).  
“SET DATE/TIME!” appears.  
Snapshot mode cannot be used.  
• The date/time is not set.  
• The Squeeze mode is selected.  
¥ Set the date/time (pg. 10).  
• The built-in clock battery has run out and the  
previously set date/time has been erased.  
¥ Disengage the Squeeze mode (pg. 29).  
The color of Snapshot looks strange.  
• The light source or the subject does not include white.  
Or there are various different light sources behind the  
subject.  
¥ Consult your nearest JVC dealer for replacement.  
Recording cannot be performed.  
—— For Tape Recording ——  
¥ Find a white subject and compose your shot so that  
it also appears in the frame (pg. 17, 25).  
• The Sepia or Monotone mode is activated.  
¥ Turn off Sepia and Monotone (pg. 23).  
• The tape’s erase protection tab is set to “SAVE”.  
¥ Set the tape’s erase protection tab to “REC”  
(pg. 9).  
• The Power Switch y is set to “PLAY” or “OFF  
The image taken using Snapshot is too dark.  
• Shooting was performed under backlit conditions.  
¥ Press the BACKLIGHT Button ! (pg. 26).  
(CHARGE)”.  
¥ Set the Power Switch y to “ ” or “ ” (pg. 13).  
• The VIDEO/DSC Switch 4 is set to “DSC”.  
¥ Set the VIDEO/DSC Switch 4 to “VIDEO”.  
• “TAPE END” appears.  
¥ Replace with new cassette (pg. 9).  
• The cassette holder cover is open.  
The image taken using Snapshot is too bright.  
• The subject is too bright.  
¥ Set “PROGRAM AE” to “SPOTLIGHT” in the Menu  
Screen (pg. 23).  
¥ Close the cassette holder cover.  
Digital Zoom does not work.  
—— For Memory Card Recording ——  
• 16X optical zoom is selected.  
¥ Set “ZOOM” to “40X” or “700X” in the Menu Screen  
(pg. 28).  
• The VIDEO/DSC Switch 4 is set to “VIDEO”.  
¥ Set the VIDEO/DSC Switch 4 to “DSC”.  
• The VIDEO/DSC Switch 4 is set to “DSC”.  
¥ Set the VIDEO/DSC Switch 4 to “VIDEO”  
(pg. 13).  
There is no picture.  
• The camcorder is not getting power, or some other  
malfunction exists.  
¥ Turn the camcorder’s power off and on again  
(pg. 13).  
EN  
38  
TROUBLESHOOTING  
Images on the LCD monitor appear dark or  
whitish.  
The Black & White Fader does not work.  
The Sepia or Monotone mode is activated.  
In places subject to low temperature, images become  
dark due to the characteristics of the LCD monitor.  
When this happens, the displayed colors differ from  
those that are actually recorded. This is not a defect of  
the camcorder.  
When the LCD monitor's fluorescent light reaches the  
end of its service life, images on the LCD monitor  
become dark. Consult your nearest JVC dealer.  
¥ Turn off Sepia and Monotone (pg. 23).  
Even when Slow Shutter is not selected, the  
image looks like it is activated.  
When shooting in the dark, the unit becomes highly  
sensitive to light and the image takes on an effect  
similar to Slow Shutter.  
¥ If you want the lighting to look more natural, set  
GAIN UP to AGCor OFFin the Menu Screen  
(pg. 29).  
¥ Adjust the brightness and angle of the LCD monitor  
(pg. 12).  
The rear of the LCD monitor is hot.  
White Balance cannot be activated.  
The light used to illuminate the LCD monitor causes it  
to become hot.  
¥ Close the LCD monitor to turn it off or set the Power  
Switch y to OFF (CHARGE), and let the unit cool  
down.  
The Sepia or Monotone mode is activated.  
¥ Turn off Sepia or Monotone before setting White  
Balance (pg. 23, 27).  
When shooting a subject illuminated by bright  
light, vertical lines appear.  
This is a result of exceedingly high contrast, and is  
The indicators and the image color on the  
LCD monitor are not clear.  
not a malfunction.  
This may occur when the surface or the edge of the  
When the screen is under direct sunlight  
during shooting, the screen becomes red or  
black for an instant.  
LCD monitor is pressed.  
The LCD monitor or viewfinder indications  
blink.  
This is not a malfunction.  
Certain Fade/Wipe effects, certain modes of Program  
AE with special effects, DISand other functions that  
cannot be used together are selected at the same  
time.  
¥ Re-read the sections covering Fade/Wipe effects,  
Program AE with special effects and DIS”  
(pg. 23, 24, 29).  
The date/time does not appear.  
• “DATE/TIMEis set to OFFin the Menu Screen.  
¥ Set DATE/TIMEto ONin the Menu Screen  
(pg. 30, 32).  
Files stored on the memory card cannot be  
deleted.  
Files stored on the memory card are protected.  
¥ Remove protection from the files stored on the  
memory card and delete them (pg. 20).  
Colored bright spots appear all over the LCD  
monitor or the viewfinder.  
The LCD monitor and the viewfinder are made with  
high-precision technology. However, black spots or  
bright spots of light (red, green or blue) may appear  
constantly on the LCD monitor or the viewfinder.  
These spots are not recorded on the tape. This is not  
due to any defect of the unit. (Effective dots: more  
than 99.99 %)  
Time code does not appear.  
• “TIME CODEis set to OFFin the Menu Screen.  
¥ Set TIME CODEto ONin the Menu Screen  
(pg. 31, 32).  
During recording, sound cannot be heard.  
This is normal.  
Play, Rewind and Fast-Forward functions do  
not work.  
The Power Switch y is set to “ ” or “ ”.  
¥ Set the Power Switch y to PLAY(pg. 14).  
EN  
39  
TROUBLESHOOTING  
The charger indicator on the camcorder does  
not light.  
The temperature of the battery is extremely high/low.  
Charging is difficult in places subject to extremely  
high/low temperatures.  
¥ To protect the battery, it is recommended to charge  
it in places with a temperature of 10°C to 35°C  
(50°F to 95°F) (pg. 41).  
A memory card cannot be played back.  
The Power Switch y is set to “ ” or “ ”.  
¥ Set the Power Switch y to PLAY(pg. 18).  
The VIDEO/DSC Switch 4 is set to VIDEO.  
¥ Set the VIDEO/DSC Switch 4 to DSC.  
The LCD monitor image is distorted.  
During playback of the unrecorded portion,  
High-speed Search and still playback, LCD monitor  
indications appear distorted. This is not a defect.  
When the image is printed from the printer, a  
black bar appears at the bottom of the screen.  
Images on the LCD monitor are jittery.  
This is not a malfunction.  
The speaker volume is too great.  
¥ Turn the speaker volume down (pg. 14).  
¥ By recording with DISactivated (pg. 29) this  
can be avoided.  
When the camcorder is connected via the DV  
connector, the camcorder does not operate.  
There is no playback picture on the  
connected TV.  
The DV cable was plugged/unplugged with power  
turned on.  
Since the analog input mode is engaged, the  
camcorder is in the Record-Standby mode.  
¥ Turn the camcorders power off and on again, then  
operate it.  
¥ Set S/AV INPUTto OFFin the Menu Screen  
(pg. 31).  
The memory card cannot be removed from  
the camcorder.  
¥ Push in the memory card a few more times  
Blocks of noise appear during playback, or  
there is no playback picture and the screen  
becomes blue.  
(pg. 11).  
¥ Clean the video heads with an optional cleaning  
cassette (pg. 42).  
The LCD monitor, the viewfinder and the lens  
have become dirty (ex. fingerprints).  
¥ Wipe them gently with soft cloth. Wiping strongly  
can cause damage (pg. 43).  
An unusual mark appears.  
¥ Check the section of the manual that explains LCD  
monitor/viewfinder indications (pg. 48 51).  
An error indication (E01, E02 or E06) appears.  
A malfunction of some kind has occurred. In this case  
the camcorders functions become unusable.  
¥ Remove the power supply (battery pack, etc.) and  
wait a few minutes for the indication to clear. When it  
does, you can resume using the camcorder. If the  
indication remains even though you repeat the  
above two or three times, please consult your  
nearest JVC dealer. Do not eject the cassette. This  
will cause damage to the tape.  
An error indication (E03 or E04) appears.  
A malfunction of some kind has occurred. In this case  
the camcorders functions become unusable.  
¥ Eject the cassette once and re-insert it, then check if  
the indication clears. When it does, you can resume  
using the camcorder. If the indication remains even  
though you repeat the above two or three times,  
please consult your nearest JVC dealer.  
EN  
40  
TROUBLESHOOTING  
AC Adapter  
NOTES:  
It is normal for the battery pack to be warm after  
charging, or after use.  
When using the AC Adapter in areas other than  
the USA  
Temperature Range Specifications  
Charging ................ 10°C to 35°C (50°F to 95°F)  
Operation ............... 0°C to 40°C (32°F to 104°F)  
Storage .................. 10°C to 30°C (14°F to 86°F)  
The provided AC Adapter features automatic voltage  
selection in the AC range from 110 V to 240 V.  
USING HOUSEHOLD AC PLUG ADAPTER  
Recharging time is based on room temperature of 20°C  
(68°F).  
The lower the temperature, the longer recharging takes.  
In case of connecting the units power cord to an AC  
wall outlet other than American National Standard C73  
series type use an AC plug adapter, called a Siemens  
Plug, as shown.  
Cassettes  
To properly use and store your cassettes, be sure to  
read the following cautions:  
For this AC plug adapter, consult your nearest JVC  
dealer.  
1. During use . . .  
... make sure the cassette bears the Mini DV mark.  
... be aware that recording onto prerecorded tapes  
automatically erases the previously recorded  
video and audio signals.  
... make sure the cassette is positioned properly  
when inserting.  
... do not load and unload the cassette repeatedly  
without allowing the tape to run at all. This  
slackens the tape and can result in damage.  
... do not open the front tape cover. This exposes the  
tape to fingerprints and dust.  
2. Store cassettes . . .  
... away from heaters or other heat sources.  
... out of direct sunlight.  
... where they wont be subject to unnecessary shock  
or vibration.  
... where they wont be exposed to strong magnetic  
fields (such as those generated by motors,  
transformers or magnets).  
Plug adapter  
If there is dust or dirt on the AC Adapter, wipe it clean  
before using.  
Battery Packs  
The supplied battery pack is a  
lithium-ion battery. Before using  
the supplied battery pack or an  
optional battery pack, be sure to  
read the following cautions:  
1. To avoid hazards . . .  
... do not burn.  
... do not short-circuit the terminals. When  
transporting, make sure the provided battery cap  
is attached to the battery. If the battery cap is  
misplaced, carry the battery in a plastic bag.  
... do not modify or disassemble.  
Terminals  
... vertically, in their original cases.  
... do not expose the battery to temperatures  
exceeding 60°C (140°F), as this may cause the  
battery to overheat, explode or catch fire.  
... use only specified chargers.  
2. To prevent damage and prolong service life . . .  
... do not subject to unnecessary shock.  
... charge in an environment where temperatures are  
within the tolerances shown in the following chart.  
This is a chemical reaction type batterycooler  
temperatures impede chemical reaction, while  
warmer temperatures can prevent complete  
charging.  
... store in a cool, dry place. Extended exposure to  
high temperatures will increase natural discharge  
and shorten service life.  
... fully charge and then fully discharge the battery  
every 6 months when storing the battery pack  
over a long period time.  
Memory Cards  
To properly use and store your memory cards, be sure  
to read the following cautions:  
1. During use . . .  
... make sure the memory card bears the SD or  
MultiMediaCard mark.  
... make sure the memory card is positioned properly  
when inserting.  
2. While the memory card is being accessed  
(during recording, playback, deletion,  
initialization, etc.) . . .  
... never unload the memory card and never turn off  
the camcorder.  
3. Store memory cards . . .  
... away from heaters or other heat sources.  
... out of direct sunlight.  
... where they wont be subject to unnecessary shock  
or vibration.  
... where they wont be exposed to strong magnetic  
fields (such as those generated by motors,  
transformers or magnets).  
... remove from charger or powered unit when not in  
use, as some machines use current even when  
switched off.  
EN  
41  
CAUTIONS  
5. Dirty heads can cause the following problems:  
LCD Monitor  
1. To prevent damage to the LCD monitor,  
DO NOT . . .  
... push it strongly or apply any shocks.  
... place the camcorder with the LCD monitor on the  
bottom.  
2. To prolong service life . . .  
... avoid rubbing it with coarse cloth.  
3. Be aware of the following phenomena for LCD  
monitor use.  
No picture during playback.  
Blocks of noise appear during playback.  
During recording or playback, the Head Clog  
Warning indicator “ ” appears.  
These are not malfunctions:  
While using the camcorder, the surface around the  
LCD monitor and/or the back of the LCD monitor  
may heat up.  
If you leave power on for a long time, the surface  
around the LCD monitor becomes hot.  
Recording cannot be performed properly.  
In such cases, use an optional cleaning cassette.  
Insert it and play back. If the cassette is used more  
than once consecutively, damage to the video heads  
may result. After the camcorder plays back for about  
20 seconds, it stops automatically. Also refer to the  
cleaning cassettes instructions.  
Main Unit  
1. For safety, DO NOT . . .  
If, after using the cleaning cassette, the problems  
still exist, consult your nearest JVC dealer.  
... open the camcorders chassis.  
... disassemble or modify the unit.  
... short-circuit the terminals of the battery pack.  
Keep it away from metallic objects when not in  
use.  
... allow inflammables, water or metallic objects to  
enter the unit.  
Mechanical moving parts used to move the video  
heads and video tape tend to become dirty and worn  
out over time. In order to maintain a clear picture at  
all times, periodic check-ups are recommended after  
using the unit for about 1,000 hours. For periodic  
check-ups please consult your nearest JVC dealer.  
... remove the battery pack or disconnect the power  
supply while the power is on.  
... leave the battery pack attached when the  
camcorder is not in use.  
2. Avoid using the unit . . .  
... in places subject to excessive humidity or dust.  
... in places subject to soot or steam such as near a  
cooking stove.  
... in places subject to excessive shock or vibration.  
... near a television set.  
... near appliances generating strong magnetic or  
electric fields (speakers, broadcasting antennas,  
etc.).  
... in places subject to extremely high (over 40°C or  
104°F) or extremely low (under 0°C or 32°F)  
temperatures.  
3. DO NOT leave the unit . . .  
... in places of over 50°C (122°F).  
... in places where humidity is extremely low (below  
35%) or extremely high (above 80%).  
... in direct sunlight.  
... in a closed car in summer.  
... near a heater.  
4. To protect the unit, DO NOT . . .  
... allow it to become wet.  
... drop the unit or strike it against hard objects.  
... subject it to shock or excessive vibration during  
transportation.  
... keep the lens directed at extremely bright objects  
for long periods.  
... expose the lens to direct sunlight.  
... carry it by holding the LCD monitor or the  
viewfinder.  
... swing it excessively when using the shoulder  
strap or the grip.  
EN  
42  
CAUTIONS  
How to handle a CD-ROM  
For Your Maintenance  
1) After Use  
Take care not to soil or scratch the mirror surface  
(opposite to the printed surface). Do not write  
anything or put a sticker on either the front or back  
surface. If the CD-ROM gets dirty, gently wipe it with a  
soft cloth outward from the center hole using a circular  
motion.  
1. Turn off the camcorder.  
2. Slide and hold OPEN/EJECT W in the direction  
of the arrow, then pull the cassette holder cover  
open until it locks. The cassette holder opens  
automatically. Remove the cassette.  
Do not use conventional disc cleaners or cleaning  
spray.  
3. Press PUSH HEREto close the cassette holder.  
Do not bend the CD-ROM or touch its mirror surface.  
Do not store your CD-ROM in a dusty, hot or humid  
environment. Keep it away from direct sunlight.  
Once the cassette holder is closed, it recedes  
automatically. Wait until it recedes completely  
before closing the cassette holder cover.  
4. Tilt the viewfinder upward. Press BATT.  
RELEASE Q and remove the battery pack.  
About moisture condensation . . .  
You have observed that pouring a cold liquid into a  
glass will cause drops of water to form on the glass  
outer surface. This same phenomenon occurs on the  
head drum of a camcorder when it is moved from a  
cool place to a warm place, after heating a cold room,  
under extremely humid conditions or in a place  
directly subjected to the cool air from an air  
conditioner.  
2) Cleaning The Camcorder  
1. To clean the exterior, wipe gently with a soft cloth.  
Put the cloth in diluted mild soap and wring it well  
to wipe off heavy dirt. Then wipe again with a dry  
cloth.  
2. Open the LCD monitor. Wipe gently with a soft  
cloth. Be careful not to damage the monitor.  
Close the LCD monitor.  
Moisture on the head drum can cause severe  
damage to the video tape, and can lead to internal  
damage to the camcorder itself.  
3. To clean the lens, blow it with a blower brush,  
then wipe gently with lens cleaning paper.  
NOTES:  
Serious malfunctioning  
Avoid using strong cleaning agents such as benzine or  
alcohol.  
If malfunctioning occurs, stop using the unit  
immediately and consult your local JVC dealer.  
Cleaning should be done only after the battery pack has  
been removed or other power units have been  
disconnected.  
Mold may form if the lens is left dirty.  
When using a cleaner or chemically treated cloth refer to  
the cautions of each product.  
The camcorder is a microcomputer-controlled  
device. External noise and interference (from a TV,  
a radio, etc.) might prevent it from functioning  
properly. In such cases, first disconnect its power  
supply unit (battery pack, AC Adapter, etc.) and wait  
a few minutes and then re-connect it and proceed  
as usual from the beginning.  
EN  
43  
CAUTIONS  
For GR-D90US and GR-D70US Owners:  
Declaration of Conformity  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme  
à la norme NMB-003 du Canada.  
Model Number  
Trade Name  
: GR-D90US/D70US  
: JVC  
Responsible party : JVC AMERICAS CORP.  
Address  
: 1700 Valley Road Wayne,  
N. J. 07470  
Telephone Number : 973-3175000  
This device complies with Part 15 of FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference,  
and (2) this device must accept any interference  
received, including interference that may cause  
undesired operation.  
For GR-D90US, GR-D70US and GR-D30US  
Owners:  
This device complies with Part 15 of FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference,  
and (2) this device must accept any interference  
received, including interference that may cause  
undesired operation.  
Change or modifications not approved by the party  
responsible for compliance could void the users  
authority to operate the equipment. This equipment  
has been tested and found to comply with the limits  
for a Class B digital device, pursuant to Part 15 of  
the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference  
in a residential installation. This equipment  
generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance  
with the instructions, may cause harmful interfer-  
ence to radio communications. However, there is no  
guarantee that interference will not occur in a  
particular installation. If this equipment does cause  
harmful interference to radio or television reception,  
which can be determined by turning the equipment  
off and on, the user is encouraged to try to correct  
the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment  
and receiver.  
Connect the equipment into an outlet on a circuit  
different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV  
technician for help.  
EN  
44  
CAUTIONS  
Digital Still Camera Function (GR-D90/D70 only)  
Camcorder  
Storage media  
Compression  
system  
: SD Memory Card/MultiMediaCard  
General  
Power supply  
:
DC 11.0 V  
DC 7.2 V  
(Using AC Adapter)  
(Using battery pack)  
: JPEG (compatible)  
: 2 modes (1024 x 768 pixels,  
640 x 480 pixels)  
File size  
Power consumption  
LCD monitor off,  
viewfinder on : Approx. 3.4 W  
LCD monitor on,  
viewfinder off : Approx. 4.7 W  
Dimensions  
Picture quality  
Approximate  
number of  
: 2 modes (FINE/STANDARD)  
storable images : pg. 18.  
(W x H x D)  
: 76 mm x 94 mm x 143 mm (3" x  
3-3/4" x 5-11/16") (GR-D90)  
69 mm x 94 mm x 143 mm (2-3/4"  
x 3-3/4" x 5-11/16") (GR-D70/D30)  
(with the LCD monitor closed and  
the viewfinder pushed back in)  
: Approx. 550 g (1.3 lbs) (GR-D90)  
Approx. 525 g (1.2 lbs) (GR-D70/  
D30)  
Connectors  
S-Video  
Output  
: Y : 1 V (p-p), 75 , analog  
C : 0.29 V (p-p), 75 , analog  
Input*  
: Y : 0.8 V (p-p) – 1.2 V (p-p), 75 ,  
Weight  
analog  
C : 0.2 V (p-p) – 0.4 V (p-p), 75 ,  
analog  
Operating  
temperature  
Operating  
humidity  
Storage  
temperature  
Pickup  
Lens  
AV  
: 0°C to 40°C (32°F to 104°F)  
: 35% to 80%  
Video output  
Video input*  
: 1 V (p-p), 75 , analog  
: 0.8 V (p-p) – 1.2 V (p-p), 75 ,  
analog  
: 300 mV (rms), 1 k, analog,  
stereo  
: 300 mV (rms), 50 k, analog,  
stereo  
Audio output  
Audio input*  
: –20°C to 50°C (–4°F to 122°F)  
: 1/6" CCD  
: F 1.6, f = 2.7 mm to 43.2 mm,  
16:1 power zoom lens  
DV  
Output  
Input  
Filter diameter  
LCD monitor  
: ø37 mm  
: 4-pin, IEEE 1394 compliant  
: 4-pin, IEEE 1394 compliant  
: 5-pin  
: 3.5" diagonally measured, LCD  
panel/TFT active matrix system  
(GR-D90)  
USB*  
2.5" diagonally measured, LCD  
panel/TFT active matrix system  
(GR-D70/D30)  
* GR-D90/D70 only  
Viewfinder  
Speaker  
: Electronic viewfinder with 0.24"  
black/white LCD  
: Monaural  
AC Adapter  
Power requirement  
U.S.A. and  
Canada  
: AC 120 V`, 60 Hz  
Digital Video Camera  
Other countries : AC 110 V to 240 V`, 50 Hz/60 Hz  
Output : DC 11 V , 1 A  
Format  
: DV format (SD mode)  
: NTSC standard  
Signal format  
Recording/  
Playback format : Video: Digital component recording  
: Audio: PCM digital recording,  
32 kHz 4-channel (12-bit),  
48 kHz 2-channel (16-bit)  
Cassette  
: Mini DV cassette  
Tape speed  
: SP : 18.8 mm/s  
LP : 12.5 mm/s  
Maximum  
recording time : SP : 80 min.  
(using 80 min.  
cassette)  
LP : 120 min.  
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject  
to change without notice.  
EN  
45  
SPECIFICATIONS  
Controls, Connectors And Indicators  
Refer to this diagram while reading the instructions.  
1
4
5 6 7 8 9  
LCD monitor  
2
3
0 ! @  
#
Speaker  
$
u
Viewfinder  
% ^ &  
* (  
)
q
w
e
Stereo  
microphone  
i o p  
r
t
(
)
CHARGE  
OFF  
PLAY  
Q
y
W
E
R
Y
I
s
f
h
d
g
j
T
U
O
a
k
;
P
l
A
Remote Control  
(provided with  
GR-D90/D70 Only)  
EN  
INDEX  
46  
1 • Remote Sensor (GR-D90/D70 only)  
The transmitted beam’s approximate effective  
distance for indoor use is 5m (16ft).  
p MEMORY CARD Cover  
(GR-D90/D70 only) ................................... pg. 11  
Q Battery Release Button [BATT. RELEASE] .... pg. 7  
W OPEN/EJECT Switch .................................. pg. 9  
E Infrared Beam Transmitting Window  
Transmits the beam signal.  
The transmitted beam may not be effective or may  
cause incorrect operation outdoors or when the  
remote sensor is directly exposed to sunlight or  
powerful lighting.  
• Camera Sensor  
Be careful not to cover this area, a sensor  
necessary for shooting is built-in here.  
R Snapshot Button* [S. SHOT]  
T Audio Monitor Button [AUDIO] .................. pg. 32  
Y PAUSE Button*  
• Up Button ................................................ pg. 35  
U SLOW Button [9] ...................................... pg. 35  
I • REW Button*  
2 Grip Strap .................................................... pg. 8  
3 Tally Lamp ........................................... pg. 12, 30  
4 VIDEO/DSC Switch [VIDEO, DSC]  
(GR-D90/D70 only) ................................... pg. 13  
• Left Button ............................................... pg. 35  
O INSERT Button .......................................... pg. 36  
P • STOP Button*  
• Down Button............................................ pg. 35  
a SHIFT Button............................................. pg. 35  
s START/STOP Button*  
5 Stop Button [5] ......................................... pg. 14  
6 Rewind Button [2] .................................. pg. 14  
7 Play/Pause Button [4/6]........................... pg. 14  
8 Fast-Forward Button [3] ......................... pg. 14  
9 USB (Universal Serial Bus) Connector  
(GR-D90/D70 only) ................................... pg. 37  
0 • INFO Button (GR-D90/D70 only) ............ pg. 19 d ON/OFF Button ......................................... pg. 35  
• NIGHT Button.......................................... pg. 23  
! • INDEX Button (GR-D90/D70 only) .......... pg. 19  
• BACKLIGHT Button................................. pg. 26  
@ Digital Video Connector [DV] (i.Link*) ... pg. 34, 37  
f EFFECT Button ......................................... pg. 35  
g SLOW Button [0] ...................................... pg. 35  
h • FF Button*  
• Right Button ............................................ pg. 35  
j PLAY Button*  
k A. DUB Button ........................................... pg. 36  
l DISPLAY Button .................................. pg. 16, 33  
; Zoom (T) Button .................................. pg. 13, 35  
A Zoom (W) Button ................................. pg. 13, 35  
* i.Link refers to the IEEE1394-1995 industry  
specification and extensions thereof. The  
used for products compliant with the i.Link  
standard.  
logo is  
# Battery Pack Mount ..................................... pg. 7  
$ DC Input Connector .................................... pg. 7  
% • MENU Wheel [+, –] ................................. pg. 28  
• Speaker Volume Control [VOLUME]........ pg. 14  
^ Snapshot Button [SNAPSHOT] ........... pg. 17, 25  
& Power Zoom Lever [T/W] ........................... pg. 13  
* • FOCUS Button ........................................ pg. 26  
• BLANK SEARCH Button ......................... pg. 15  
( Audio/Video Input (GR-D90/D70 only)/  
Output Connector [AV] ........................ pg. 16, 33  
) S-Video Input (GR-D90/D70 only)/  
Output Connector [S-VIDEO] .............. pg. 16, 33  
q Diopter Adjustment Control ......................... pg. 8  
w Recording Start/Stop Button ..................... pg. 12  
e Shoulder Strap Eyelets................................ pg. 9  
r POWER/CHARGE Lamp ................ pg. 7, 12, 13  
t Lock Button ............................................... pg. 13  
y Power Switch  
* Functions the same as each corresponding button on  
the camcorder.  
[
,
, PLAY, OFF (CHARGE)] .............. pg. 13  
u Monitor Open Button ................................. pg. 12  
For models without button, simply pull on bottom  
end of LCD monitor to open.  
The connector ) is located beneath a cover.  
i Stud Hole .................................................... pg. 9  
o Tripod Mounting Socket .............................. pg. 9  
EN  
47  
INDEX  
LCD Monitor/Viewfinder Indications  
During Tape Recording Only During Tape Playback  
1
2
3 4 5 6  
p
Q
W
E
1h50m  
REC  
12b i t  
L
/
SOUND  
1
4
6
w
6
BLANK SEARCH  
SOUND 12b i t  
15 : 55  
VOLUME  
DEC 25 03  
10 : 00 AM  
116 : 21 : 25  
!
0
9
8 7  
Y
T
R
u
During Memory Card Recording Only  
(GR-D90/D70 only)  
During Memory Card Playback  
(GR-D90/D70 only)  
@
# $ % ^  
U
I
1024  
100 - 0011  
15  
BR I GHT  
O
u
During Both Tape And Memory Card Recording  
e r  
t
y
&
*
40x W  
T
PHOTO  
(
)
q
3
w
BR I GHT  
JAN 10 ’ 03  
10 : 00 AM  
o
i
u
EN  
INDEX  
48  
1 Displays the selected Fade/Wipe effect .... pg. 24  
r Appears during zooming  
Zoom level indicator ............................ pg. 13  
2 Appears when in the Squeeze or Cinema mode  
.................................................................. pg. 29  
t Displays the brightness of the LCD monitor  
.................................................................. pg. 12  
3 Rotates while the tape is running .............. pg. 12  
4 Displays the recording mode (SP or LP) ... pg. 10  
5 Displays the tape remaining time .............. pg. 12  
6 • “RECappears during recording  
y Appears when taking a Snapshot ....... pg. 17, 25  
u Displays the battery remaining power level.  
.................................................................. pg. 50  
i Displays the date/time ................... pg. 10, 30, 32  
• “PAUSEappears during Record-Standby mode  
................................................................ pg. 12  
7 Appears when the wind cut mode is engaged to cut  
down on noise created by wind ................. pg. 29  
o Appears when the focus is adjusted manually  
............................................................ pg. 25, 26  
p Displays the sound mode .................... pg. 31, 32  
Q Displays the Blank Search mode .............. pg. 15  
W Displays the tape speed ............................ pg. 10  
E Appears while a tape is running  
8 Appears when the Insert Editing (w) or Insert Editing  
Pause (6w) mode is engaged  
(GR-D90/D70 only) ................................... pg. 36  
9 Displays the sound mode for approx. 5 seconds  
after turning on the camcorder .................. pg. 28  
0 Displays the Time Code ...................... pg. 14, 31  
! Appears when Digital Image Stabilizer (DIS) is  
engaged .................................................... pg. 29  
@ Displays the image size ............................ pg. 11  
# Appears and blinks during shooting .......... pg. 17  
4
: Playback  
3
2
6
: Fast-Forward/Shuttle Search  
: Rewind/Shuttle Search  
: Pause  
6
1
e
4
: Forward Frame-By-Frame Playback/Slow-  
Motion  
: Reverse Frame-By-Frame Playback/Slow-  
Motion  
6
$ •  
: Appears during shooting ................ pg. 17  
: Blinks when a memory card is not loaded  
....................................................... pg. 17  
: Audio Dubbing (GR-D90/D70 only)  
6e : Audio Dubbing Pause (GR-D90/D70 only)  
R Displays the date/time ......................... pg. 30, 32  
% Displays the picture quality  
There are 2 modes available: F (Fine) and  
S (Standard) (in order of quality) ............... pg. 11  
T BRIGHT : Displays the brightness of the LCD  
monitor ................................ pg. 12  
^ Displays the remaining number of shots that can be  
stored.  
VOLUME : Displays the speaker volume  
............................................ pg. 14  
The number increases or decreases depending on  
the Picture Quality/Image Size, etc. .......... pg. 17  
The level indicator moves.  
Y Displays the time code ........................ pg. 31, 32  
U Displays the operation mode ..................... pg. 19  
I Displays the folder and file number ........... pg. 19  
& Appears when the Power Switch is set to “  
.................................................................. pg. 13  
* •  
: Appears when Night-Alive is engaged  
..................................................... pg. 23  
O Displays the brightness of the LCD monitor  
.................................................................. pg. 12  
: Appears when GAIN UPis set to AUTO”  
and the shutter speed is being automatically  
adjusted ........................................ pg. 29  
The level indicator moves.  
( Appears when the white balance is adjusted  
.................................................................. pg. 27  
) • “ؓ: Appears when the exposure is adjusted  
..................................................... pg. 26  
: Appears when backlight compensation is  
used.............................................. pg. 26  
q Displays the selected Program AE with special  
effects ........................................................ pg. 23  
w Appears when the iris is locked ................. pg. 27  
e Approximate zoom ratio: Appears during zooming  
.................................................................. pg. 13  
EN  
INDEX  
49  
WARNING INDICATIONS  
(high)  
A. DUB ERROR!  
<CANNOT DUB ON A LP RECORDED TAPE>  
<CANNOT DUB ON A 16BIT RECORDING>  
<CHECK TAPES ERASE PROTECTION TAB>  
(exhausted)  
Displays the battery remaining power level. As the  
battery power comes close to nil, the battery indicator  
blinks (battery power warning). When the battery  
power is exhausted, power turns off automatically.  
Appears if Audio Dubbing is attempted on a tape  
recorded in the LP mode.  
Appears if Audio Dubbing is attempted on a tape  
recorded in 16-bit audio.  
Appears if A. DUB (e) k on the remote control is  
pressed when the erase protection tab is set to  
Appears when no tape is loaded.  
(pg. 9)  
SAVE.  
(pg. 36)  
CHECK TAPES ERASE PROTECTION TAB  
Appears when the erase protection tab is set to SAVE”  
while the Power Switch y is set to “ ” or “ ” and  
the VIDEO/DSC Switch 4 (GR-D90/D70 only) is set to  
INSERT ERROR!  
Appears if Insert Editing is attempted on a blank portion  
of a tape.  
(pg. 36)  
VIDEO.  
(pg. 9)  
INSERT ERROR!  
<CANNOT EDIT ON A LP RECORDED TAPE>  
<CHECK TAPES ERASE PROTECTION TAB>  
HEAD CLEANING REQUIRED USE CLEANING  
CASSETTE  
Appears if dirt is detected on the heads during  
recording or playback. Use an optional cleaning  
Appears if Insert Editing is attempted on a tape  
recorded in the LP mode.  
Appears if INSERT (w) O on the remote control is  
pressed when the erase protection tab is set to  
cassette.  
(pg. 42)  
CONDENSATION, OPERATION PAUSED  
PLEASE WAIT  
SAVE.  
(pg. 36)  
Appears if condensation occurs. When this indication is  
displayed, wait more than 1 hour until condensation  
disappears.  
MEMORY IS FULL  
Appears when the memory cards memory is full and  
shooting is not possible.  
TAPE!  
COPYING FAILED  
Appears if a tape is not loaded when the Recording  
Start/Stop Button w or SNAPSHOT Button ^ is  
pressed while the Power Switch y is set to “ ” or  
Appears if dubbing of copyguarded signals is at-  
tempted while this camcorder is being used as a  
recorder.  
and the VIDEO/DSC Switch 4 (GR-D90/D70  
COPYING FAILED  
<MEMORY CARD!>  
<MEMORY IS FULL>  
<PLEASE FORMAT>  
only) is set to VIDEO.  
TAPE END  
Appears when the tape ends during recording or  
playback.  
Appears in the following cases when dubbing from a  
tape to a memory card:  
when no memory card is loaded.  
when the memory card's memory is full.  
when the memory card is not formatted.  
SET DATE/TIME!  
Appears when the date/time is not set.  
(pg. 10)  
Appears when the built-in clock battery runs out and  
the previously set date/time is erased. Consult your  
nearest JVC dealer for replacement.  
MEMORY CARD!  
Appears if there is no memory card loaded when you  
attempt to record on a memory card or access data on  
a memory card.  
LENS CAP  
Appears for 5 seconds after power is turned on if the  
lens cap is attached.  
PLEASE FORMAT  
A. DUB ERROR!  
Appears when there is a problem with a memory card  
and its memory is corrupt, or it has not been initialized.  
Appears if Audio Dubbing is attempted on a blank  
portion of a tape.  
(pg. 36)  
Initialize the memory card.  
(pg. 22)  
NO IMAGES STORED  
Appears if there are no image files stored on the  
memory card when you attempt memory card  
playback.  
EN  
50  
INDEX  
CARD ERROR!  
Appears when the camcorder does not recognize the  
loaded memory card. Remove the memory card once  
and insert it again. Repeat these procedures until no  
indication appears. If the indication still appears, the  
memory card is corrupted.  
UNSUPPORTED FILE!  
Appears if a file in another format is selected.  
CHECK CARDS WRITE PROTECTION SWITCH  
Appears when you attempt to record on a SD Memory  
Card with its write/erase protection tab in the LOCK”  
position.  
Appears when you attempt Memory Card menu  
operation using a SD Memory Card with its write/  
erase protection tab in the LOCKposition.  
E01, E02 or E06 UNIT IN SAFEGUARD MODE  
REMOVE AND REATTACH BATTERY  
The error indications (E01, E02 or E06) show what type  
of malfunction has occured. When an error indication  
appears, the camcorder turns off automatically.  
Remove the power supply (battery, etc.) and wait a few  
minutes for the indication to clear. When it does, you  
can resume using the camcorder. If the indication  
remains, consult your nearest JVC dealer.  
E03 or E04 UNIT IN SAFEGUARD MODE EJECT  
AND REINSERT TAPE  
The error indications (E03 or E04) show what type of  
malfunction has occured. When an error indication  
appears, the camcorder turns off automatically. Eject  
the cassette once and re-insert it, then check if the  
indication clears. When it does, you can resume using  
the camcorder. If the indication remains, consult your  
nearest JVC dealer.  
EN  
51  
INDEX  
A
F
AC Adapter................................................... pg. 7, 8  
Analog Input ............................................. pg. 31, 33  
Audio Dubbing................................................ pg. 36  
Auto Date ....................................................... pg. 30  
Auto Focus ..................................................... pg. 25  
Auto Playback ................................................ pg. 19  
Auto Shut off ...................................... pg. 12, 15, 17  
Fade-In/Out .................................................... pg. 24  
Fast-Forward The Tape .................................. pg. 14  
Frame-By-Frame Playback ...................... pg. 14, 35  
G
Gain Up .......................................................... pg. 29  
Grip Adjustment ............................................... pg. 8  
I
B
Icons ...................................................... pg. 28 32  
Index Playback............................................... pg. 19  
Index Screen .................................................. pg. 19  
Initialize A Memory Card ................................ pg. 22  
Insert Editing .................................................. pg. 36  
Iris .................................................................. pg. 27  
Iris Lock .......................................................... pg. 27  
Backlight Compensation ................................ pg. 26  
Battery Low .................................................... pg. 50  
Battery Pack ........................................... pg. 7, 8, 41  
Beep............................................................... pg. 30  
Blank Search.................................................. pg. 15  
Brighten The LCD Monitor ............................. pg. 12  
C
J
Channels (Left/Right) ..................................... pg. 32  
Charge The Battery Pack ................................. pg. 7  
Cinema ........................................................... pg. 29  
Classic Film.................................................... pg. 23  
Clean The Camcorder .................................... pg. 43  
Connections ............................. pg. 7, 16, 33, 34, 37  
Journalistic Shooting ...................................... pg. 13  
L
LCD monitor/Viewfinder Indications ....... pg. 48 51  
Load A Tape ..................................................... pg. 9  
M
D
Maintenance .................................................. pg. 43  
Manual Focus ................................................ pg. 26  
Memory Card ........................................... pg. 11, 41  
Menu Screen, CAMERA .......................... pg. 28, 29  
Menu Screen, CAMERA DISPLAY .......... pg. 30, 31  
Menu Screen, DSC .................................. pg. 11, 31  
Menu Screen, MANUAL................................. pg. 29  
Menu Screen, SYSTEM ................................. pg. 30  
Menu Screen, VIDEO .................................... pg. 31  
Menu Screen, VIDEO DISPLAY .................... pg. 32  
Monotone ....................................................... pg. 23  
Motor Drive Mode .......................................... pg. 25  
MultiMediaCard ........................................ pg. 11, 41  
Darken The LCD Monitor ............................... pg. 12  
Date/Time Display .................................. pg. 30 32  
Date/Time Settings ........................................ pg. 10  
Deleting Files ................................................. pg. 20  
Demonstration Mode .................................. pg. 6, 30  
Digital Zoom ............................................. pg. 13, 28  
DIS (Digital Image Stabilizer) ......................... pg. 29  
Diopter Adjustment .......................................... pg. 8  
DPOF (Digital Print Order Format)........... pg. 21, 22  
Dubbing .................................................... pg. 33, 34  
E
Erase Protection .............................................. pg. 9  
Exposure Control ........................................... pg. 26  
N
Night-Alive...................................................... pg. 23  
EN  
52  
TERMS  
P
T
Picture Quality/Image Size............................. pg. 11  
Playback Special Effects ................................ pg. 35  
Playback Zoom .............................................. pg. 35  
Power-Linked Operation................................. pg. 13  
Power Switch Position .................................... pg. 13  
Program AE With Special Effects ................... pg. 23  
Protecting Files .............................................. pg. 20  
Provided Accessories ...................................... pg. 5  
Tally ................................................................ pg. 30  
Tele Macro ..................................................... pg. 29  
Time Code ....................................... pg. 14, 30 32  
Tripod Mounting ............................................... pg. 9  
Twilight ........................................................... pg. 23  
U
Unload A Tape.................................................. pg. 9  
V
R
VIDEO/DSC Switch Position .......................... pg. 13  
Record-Standby ............................................. pg. 12  
Recording Mode............................................. pg. 10  
Remote Control .......................................... pg. 5, 35  
Reset.............................................................. pg. 30  
Rewind The Tape ........................................... pg. 14  
W
White Balance ................................................ pg. 27  
Wide Mode ..................................................... pg. 29  
Wind Cut ........................................................ pg. 29  
Wipe In/Out .................................................... pg. 24  
S
SD Memory Card ..................................... pg. 11, 41  
Self-Recording ............................................... pg. 13  
Sepia .............................................................. pg. 23  
Shuttle Search ............................................... pg. 14  
Shutter Speed ................................................ pg. 23  
Slow-Motion Playback.............................. pg. 14, 35  
Snapshot .................................................. pg. 17, 25  
Snapshot Mode .............................................. pg. 25  
Snow .............................................................. pg. 23  
Sound Mode....................................... pg. 28, 31, 32  
Speaker Volume ............................................. pg. 14  
Specifications ................................................. pg. 45  
Sports ............................................................ pg. 23  
Spotlight ......................................................... pg. 23  
Squeeze ......................................................... pg. 29  
Still Playback .................................................. pg. 14  
Strobe ............................................................ pg. 23  
Z
Zooming ......................................................... pg. 13  
EN  
53  
TERMS  
MEMO  
MEMO  
VICTOR COMPANY OF JAPAN, LIMITED  
Printed in Malaysia  
1102-HO-UN-PJ  
US  
COPYRIGHT© 2002 VICTOR COMPANY OF JAPAN, LTD.  

A O Smith NW 37 670 User Manual
Audiovox 1187001PL User Manual
Barco R9849853 User Manual
Bassworx BA3000 1D User Manual
Canon 500 HS User Manual
Canon Leather Soft Case 20 User Manual
Canon VR 10 User Manual
Clarion DXZ925 User Manual
Cornelius 6 Flavor User Manual
Ikelite DCR HC14 User Manual