COMPACT VHS CAMCORDER
GR-AXM25
Compact VHS
For Customer Use:
Enter below the Model No. and Serial
No. which is located on the bottom of
cabinet. Retain this information for
future reference.
Model No.
INSTRUCTIONS
Serial No.
LYT0002-0K8A
EN
3
5. Ventilation
IMPORTANT PRODUCT
SAFETY INSTRUCTIONS
Slots and openings in the cabinet are provided for
ventilation. To ensure reliable operation of the product
and to protect it from overheating, these openings must
not be blocked or covered.
•Do not block the openings by placing the product on
a bed, sofa, rug or other similar surface.
•Do not place the product in a built-in installation
such as a bookcase or rack unless proper ventilation
is provided or the manufacturer’s instructions have
been adhered to.
Electrical energy can perform many useful func-
tions. But improper use can result in potential
electrical shock or fire hazards. This product has
been engineered and
manufactured to assure your personal safety. In
order not to defeat the built-in safeguards, observe
the following basic rules for its installation, use and
servicing.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
ATTENTION:
Follow and obey all warnings and instructions
marked on your product and its operating instruc-
tions. For your safety, please read all the safety and
operating instructions before you operate this
product and keep this manual for future reference.
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to
the product, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810
of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding
of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge
unit, connection to grounding electrodes, and
requirements for the grounding electrode.
INSTALLATION
1. Grounding or Polarization
(A) Your product may be equipped with a polarized
alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature.
If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of
the polarized plug.
2. Lightning
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will
prevent damage to the product due to lightning and
power-line surges.
(B) Your product may be equipped with a 3-wire
grounding-type plug, a plug having a third
(grounding) pin. This plug will only fit into a
grounding-type power outlet. This is a safety
feature.
3. Power Lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light
or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from
touching such power lines or circuits as contact with
them might be fatal.
If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding-type plug.
2. Power Sources
Operate your product only from the type of power
source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult
your product dealer or local power company. If your
product is intended to operate from battery power, or
other sources, refer to the operating instructions.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
3. Overloading
GROUND CLAMP
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a
risk of fire or electric shock.
ANTENNA
DISCHARGE UNIT
(NEC SECTION
4. Power Cord Protection
810-20)
ELECTRIC SERVICE
EQUIPMENT
Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the product.
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
4
EN
USE
SERVICING
1. Servicing
1. Accessories
To avoid personal injury:
If your product is not operating correctly or exhibits
a marked change in performance and you are
unable to restore normal operation by following the
detailed procedure in its operating instructions, do
not attempt to service it yourself as opening or
removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to
qualified service personnel.
•Do not place this product on an unstable cart,
stand, tripod, bracket or table. It may fall, causing
serious injury to a child or adult, and serious
damage to the product.
•Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer or sold
with the product.
•Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s
instructions for any mounting of the product.
•Do not try to roll a cart with small casters across
thresholds or deep-pile carpets.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
2. Product and Cart Combination
A product and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combina-
tion to overturn.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or damaged in
any way.
PORTABLE CART WARNING
(Symbol provided by RETAC)
3. Water and Moisture
Do not use this product
near water—for example,
near a bath tub, wash
bowl, kitchen sink or
laundry tub, in a wet
basement, or near a
swimming pool and the
like.
f. When the product exhibits a distinct change in
performance—this indicates a need for service.
3. Replacement Parts
4. Object and Liquid Entry
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or
other hazards.
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result in
a fire or electric shock. Never spill liquid of any
kind on the product.
5. Attachments
4. Safety Check
Do not use attachments not recommended by the
manufacturer of this product as they may cause
hazards.
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in safe
operating condition.
6. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
7. Heat
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
QUICK OPERATION GUIDE
EN
5
INSERTING A VIDEO
CASSETTE
SUPPLY POWER
Hook on.
EJECT
1
2
3
Push in.
2
4
BATT. RELEASE
PUSH
1
MONITOR OPEN
Using the battery pack
1 Hook-on the battery pack's top end to the
camcorder. (Charging procedure, ੬ pg. 8)
2 Push in the battery pack until it locks into
place.
1 Slide MONITOR OPEN to open the LCD
monitor.
•Open to an angle of over 45 degrees.
2 Press EJECT to open the cassette holder.
3 Insert a video cassette.
4 Press PUSH to close the cassette holder.
(For more details, ੬ pg. 13)
To remove the battery pack
Slide BATT. RELEASE and pull out the battery
pack.
PLAYBACK
PLAY/PAUSE
SHOOTING
3
1
STOP
LENS COVER
open/close knob
2
REW
2
Set to “CAMERA”
1
Recording Start/Stop button
3
Set to “PLAY”
1 Set the power switch to “PLAY”.
1 Slide the LENS COVER open/close knob to
open the lens cover.
2 Set the power switch to “CAMERA”.
— The power indicator will light and an
image will appear in the LCD monitor or
the viewfinder.
2 Press REW.
— The tape will automatically stop at the
beginning of the tape.
3 Press PLAY/PAUSE.
— Playback starts and the playback picture
appears in the viewfinder or the LCD
monitor.
3 Press the Recording Start/Stop button.
— Recording starts.
•To stop playback, press STOP.
(For more details, ੬ pg. 34.)
•The viewfinder switches off automatically to
save power when the LCD monitor is opened
at an angle of over 45 degrees.
•The LCD monitor turns on/off when it is
opened/closed at approx. 45 degrees.
•To stop recording temporarily, momentarily
press the Recording Start/Stop button once
again.
(For more details, ੬ pg. 15, 16)
•The viewfinder switches off automatically to
save power when the LCD monitor is
opened at an angle of over 45 degrees.
•The LCD monitor turns on/off when it is
opened/closed at approx. 45 degrees.
Or simply play back the tape on a VHS VCR
using the Cassette Adapter (VHS Playpak).
੬ pg. 37
MAJOR FEATURES
6
EN
REMEMBER
Picture Stabilizer (੬ pg. 24)
The Logical Choice
Digital Hyper Zoom
The only compact video
cassettes that can be
(੬ pg. 18)
used with your VHS VCR*
Zoom-in
Program AE with Special
Zoom-out
Effects (੬ pg. 20)
Ⅲ Auto Mode Lock Ⅲ Auto Mode Release
Ⅲ Electronic Fog Filter Ⅲ ND Effect
Ⅲ Sepia Ⅲ Twilight Ⅲ Sports
Ⅲ 1/1000 sec. High Speed Shutter
Ⅲ 1/2000 sec. High Speed Shutter
Random Assemble Editing
(੬ pg. 39 – 41)
2
8
5
4
1
6
3
7
LCD Color Monitor (੬ pg. 16)
1
2
3
4
5
6
7
8
180°
90°
PROVIDED ACCESSORIES
•AC Power Adapter/
Charger AA-V11U
•Cassette Adapter
(VHS PlayPak) C-P7U
•Battery Pack
BN-V11U
•DC Cord
•Shoulder Strap
•Lithium Battery CR2025
Cassettes marked
can be used with this camcorder.
CONTENTS
EN
7
GETTING STARTED
8
Power ..................................................................................... 8
Clock (Lithium) Battery Insertion/Removal........................................ 10
Viewfinder Adjustment ............................................................... 10
Date/Time Setting .................................................................... 11
Tape Length Setting ................................................................... 12
Recording Mode Setting .............................................................. 12
Loading/Unloading A Cassette ...................................................... 13
Grip Adjustment ....................................................................... 14
Shoulder Strap Attachment........................................................... 14
Tripod Mounting ....................................................................... 14
RECORDING
15
Basic Recording ........................................................................ 15
Basic Features.......................................................................... 18
Advanced Features .................................................................... 20
PLAYBACK
34
Basic Playback ......................................................................... 34
Features ................................................................................ 35
Basic Connections...................................................................... 36
Using The Cassette Adapter.......................................................... 37
EDITING
38
Tape Dubbing........................................................................... 38
Random Assemble Editing (R.A.Edit)................................................ 39
USER MAINTENANCE
TROUBLESHOOTING
INDEX
42
43
45
LCD monitor/Viewfinder ............................................................. 45
Controls................................................................................. 46
Connectors.............................................................................. 46
Indicators ............................................................................... 46
Other Parts............................................................................. 46
Terms .................................................................................... 48
CAUTIONS
49
51
51
52
54
55
SPECIFICATIONS
OPTIONAL ACCESSORIES
ESPAÑOL
FOR SERVICING
WARRANTY
GETTING STARTED
8
EN
Power
CHG. (charge) indicator
Marks
This camcorder’s 3-way power supply system lets you
choose the most appropriate source of power.
POWER
indicator
To AC outlet
NOTES:
● No function is available without power supply.
● Use only specified power supply.
● Do not use provided power supply units with other
equipment.
END
indicator
CHARGING THE BATTERY PACK
SUPPLY POWER
Connect the charger’s AC power cord to a wall
1
2
outlet. The power indicator lights.
REFRESH switch
REFRESH indicator
ATTACH BATTERY PACK
Align the marks and slide the battery pack in the
direction of the arrow until it locks in place.
The CHG. indicator lights.
DETACH BATTERY PACK
When charging is completed, the END indicator
lights. Slide the battery pack opposite the direction of
the arrow.
3
Hook on.
BATT. PACK
CHARGE
DISCHARGE
approx.
1
BN-V11U
BN-V12U
approx. 1 hr. 10 min.
3 hrs. 30 min.
approx.
3 hrs. 30 min.
approx. 1 hr. 10 min.
BN-V22U
BN-V25U
approx. 2 hrs. 10 min. approx. 7 hrs.
approx. 2 hrs. 40 min. approx. 10 hrs.
Push in.
2
USING THE BATTERY PACK
BATT. RELEASE
ATTACH BATTERY PACK
Hook its top end to the camcorder and push the
ATTENTION:
1
2
battery pack in until it locks in place.
Before detaching the power source,
make sure that the camcorder’s power
is turned off. Failure to do so can result
in a camcorder malfunction.
DETACH BATTERY PACK
Slide BATT. RELEASE and pull out the battery pack.
Approximate recording time (unit: min.)
**REFRESH
BATT.
PACK
LCD monitor on/
Viewfinder off
LCD monitor off/
Viewfinder on
The AC power adapter features a REFRESH
function that allows you to fully discharge the
battery pack before recharging.
BN-V11U
BN-V12U
BN-V22U
BN-V25U
50
50
105
145
55
55
115
155
To discharge the battery . . .
..... attach the battery pack to the adapter as
shown in the above illustration. Then push
REFRESH. The REFRESH indicator lights
when discharging starts, and goes out
when discharging is complete.
EN
9
**CHARGE MARKER
A charge marker is provided on the battery pack to
help you remember whether it has been charged or
not. Two colors are provided (red and black)—you
choose which one means charged and which
means discharged.
Charge marker
NOTES:
● The recording time per charge is affected by such factors as the time spent in Record/Standby mode and
the frequency of zooming. It is safer to have spare battery packs.
● Charging times noted on page 8 are for fully discharged battey pack, and discharging times are for fully
charged battery pack.
● Charging and discharging times vary according to the ambient temperature and the status of the battery
pack.
● Remember to set the charge marker after charging a battery pack or after detaching a discharged one from
your camcorder.
● Perform the REFRESH function after no less than 5 chargings.
● High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t
allow it to discharge in container, such as a bag.
● If you stop recharging or discharging part way through, make sure to remove the battery pack before
unplugging the adapter’s AC cord.
● Remove the battery pack from the adapter immediately after discharging.
● To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.
● Make sure you unplug the DC cord before charging or discharging the battery pack.
● A blinking CHG. indicator means that the battery pack has become hot. Wait until it cools down to
continue.
● The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored
for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG.
indicator should light during recharging. If not, contact your nearest JVC dealer.
USING A CAR BATTERY
Use the optional Car Battery Cord or Car Battery
Charger/Adapter (connect as shown in the
illustration to the left).
To AC outlet
DC OUT
terminal
To DC
in jack
NOTES:
● When using the car battery, leave the engine
idling.
AC Power
Adapter/Charger
AA-V11U
● The optional Car Battery Charger (BH-V3U) can
also be used to charge the battery pack.
● When using the optional Car Battery Charger or
Car Battery Cord (AP-V7U), refer to the respective
instruction booklet.
DC cord
To car's
cigarette
lighter socket
USING AC POWER
Use the AC Power Adapter (connect as shown in
the illustration to the left).
Car Battery Cord
AP-V7U (optional)
NOTE:
The supplied AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
Car Battery Charger/Adapter
BH-V3U (optional)
GETTING STARTED (cont.)
10
EN
Clock (Lithium) Battery Insertion/Removal
This battery is necessary for clock operation and to
perform date/time settings.
A
SWITCH OFF POWER
Switch off the unit’s power and remove the power
1
2
3
supply unit.
OPEN COVER
Open the clock battery compartment cover while
pressing the release tab.
REMOVE BATTERY (when replacing)
Insert a pointed, non-metallic object between the
A
battery and the compartment ( ) and pull the
battery out.
INSERT BATTERY
Ensuring the plus (+) side is up, insert a CR2025
lithium battery and push it in.
4
5
CLOSE COVER
Close the compartment cover until it clicks in place.
NOTE:
See “SAFETY PRECAUTIONS” (੬ pg. 2) for information
on safe handling of lithium batteries.
Viewfinder Adjustment
POSITION VIEWFINDER
3
Adjust the viewfinder manually for best viewability
1
2
3
(see illustration at left).
SELECT MODE
1
Set the power switch to CAMERA.
2
ADJUST DIOPTER
Turn the diopter adjustment control until the
indications in the viewfinder are clearly focused.
Set POWER to “CAMERA”.
EN
11
Date/Time Setting
NEAR
SELECT MODE
First set the power switch to “CAMERA”. Turn the
PROGRAM AE select dial to any position except
AUTO LOCK.
1
ACCESS MENU SCREEN
Press MENU.
MENU FAR
2
3
SELECT FUNCTION
Press – to move the highlight bar down to “Date/
Time”, then press NEAR. The Set Date And Time
screen appears.
SET DATE/TIME
Press FAR or NEAR until the item you want to set
begins blinking, then press + or – to until the correct
setting appears.
4
•If you decide you want to return the date and time
to the previous settings, press FAR or NEAR to
move the highlight bar to “Cancel”, then press
MENU.
•If you’re satisfied with the settings, go on to step 5.
PROGRAM AE select dial
START CLOCK OPERATION
Once you’ve set the date and time, press FAR or
NEAR until “Set” begins to blink, then press MENU.
The Menu screen reappears.
LCD monitor or viewfinder
5
6
Gain Up
S.LX
OFF
OFF
OFF
07
Tele Macro
Interval Timer
Rec Time
Menu Screen
CLOSE MENU
Press MENU.
JLIP ID NO.
Tally
ON
Set Character
Date/Time
NOTES:
END :MENU KEY
● To display the date and time in the LCD monitor or the
viewfinder and on a connected TV, see “Date/Time
Insert” (੬ pg. 28).
● If, in step 4, you input an invalid date (FEB 30, JUN 31,
etc.) and perform step 5, “Input Error” appears blinking
at the bottom of the screen. Press +, –, FAR or NEAR to
input the correct number.
Set Time and
Date Screen
JAN 1.00 AM 12:00
Set Cancel
Date
Month/Day/Year
Time
12-hour indication with
AM or PM
GETTING STARTED (cont.)
12
EN
Tape Length Setting
T20•30•40 tape length select button
Set the tape length according to the length of the tape
used.
SET TAPE LENGTH
Press T20•30•40 until the required indication
SP-EP recording
mode button
1
appears in the LCD monitor or the veiwfinder. T20 =
20 minutes of recording time, T30 = 30 minutes,
and T40 = 40 minutes (in SP).
NOTE:
The tape remaining time (੬ pg. 15) displayed in the
LCD monitor or the viewfinder is correct only if the
correct tape length has been selected.
Recording Mode Setting
Set depending on your preference.
SET RECORDING MODE
Press SP•EP button. “SP” (Standard Play) provides
Set POWER to “CAMERA”.
1
higher picture and sound quality and is better for
dubbing, while “EP” (Extended Play) is more
economical, recording at 1/3 the speed of SP.
Tape length indicator
NOTE:
T30
T20
T30
T40
If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
LCD monitor or
viewfinder
Recording mode indicator
SP
SP
EP
EN
13
Loading/Unloading A Cassette
OPEN LCD MONITOR
Slide MONITOR OPEN and open the LCD monitor
to an angle of over 45 degrees.
2
1
2
3
4
5
4
OPEN CASSETTE HOLDER
Press EJECT until the holder opens. Do not use force
to open.
3
1
5
INSERT/REMOVE CASSETTE
1
Make sure the label is facing outward.
CLOSE CASSETTE HOLDER
Press PUSH and make sure the holder is closed and
locked.
CLOSE LCD MONITOR
First make sure the holder is closed. Then close the
LCD monitor.
Turn to take
up slack.
Erase Protection
Gear
NOTES:
● Closing the LCD monitor while the cassette holder is
still open may cause damage to the LCD monitor.
● A cassette holder can’t be opened unless a power
supply is attached.
● Make sure that the tape is not slack when loading the
cassette. If there is any slack, turn the gear on the
cassette in the direction of the arrow to take up the
slack.
● Make sure the Erase Protection tab is in the position
that allows recording. If not, slide the tab. Some
cassettes have removable tabs. If the tab has been
removed, cover the hole with adhesive tape.
● The cassette holder can’t be opened while the
camcorder is in the record mode.
GETTING STARTED (cont.)
Grip Adjustment
14
EN
EXPAND LOOP
Separate the Velcro strip.
1
2
3
INSERT HAND
Pass your right hand through the loop and grasp the
grip.
ADJUST STRAP LENGTH
Adjust so your thumb and fingers can easily operate
the Recording Start/Stop button and Power Zoom
lever. Refasten the Velcro strip.
Recording Start/Stop button
Shoulder Strap Attachment
ATTACH STRAP
Following the illustration at left, thread the strap
1
through the top of the eyelet 1, then fold it back
and thread it through the keeper 2, and then
through the buckle 3. Repeat the procedure to
attach the other end of the strap to the other eyelet,
making sure the strap isn’t twisted.
1
3
2
2
1
ADJUST LENGTH
Adjust as shown in the illustration at left 1, then
slide both keepers snug against the eyelets to
prevent slipping 2.
2
Tripod Mounting
ALIGN AND TIGHTEN
Align the screw and camera direction stud on the
tripod with the camera’s mounting socket and stud
hole. Then tighten the screw.
1
CAUTION:
When using a tripod, be sure to open and extend
its legs fully to stabilize the camcorder. To
prevent damage to the unit caused by falling
over, do not use a small-sized tripod.
RECORDING Basic Recording
EN
15
NOTE:
Tape remaining time indicator
You should already have performed the procedures listed
below. If not, do so before continuing.
● Power (੬ pg. 8)
● Tape Length/Recording Mode Setting (੬ pg. 12)
● Grip Adjustment (੬ pg. 14)
25min
*---min
(Now calculating)
120min
119min
LOAD A CASSETTE
First slide MONITOR OPEN and open the LCD
monitor to an angle of over 45 degrees.
1
Press EJECT to open the cassette holder, then insert
the cassette with the label facing out. Press PUSH to
ensure the holder is closed and locked.
Power indicator
3min
2min (Blinking)
1min (Blinking)
0min (Blinking)
Shooting while watching the viewfinder
ENTER RECORD–STANDBY MODE
Make sure the LCD monitor is closed and locked.
2
Slide the LENS COVER open/close switch to open
the lens cover, then set the power switch to
CAMERA.
•The power indicator lights and the camcorder
enters the Record–Standby mode.
•The scene you’re aimed at appears on the
viewfinder screen, with the word “PAUSE”
superimposed upon it.
LENS COVER
Switch
DISPLAY button
START SHOOTING
Press the Recording Start/Stop button.
POWER
Start/Stop
3
4
•The tally lamp lights while recording is in progress,
and “REC ” appears in the viewfinder.
STOP RECORDING
Tally lamp
Press the Recording Start/Stop button again to stop
recording.
•The camcorder re-enters the Record-Standby
mode.
NOTES:
● When the power switch is set to CAMERA and the LCD monitor is opened at an angle of 45 degrees or more, the
LCD monitor switches on and the viewfinder switches off automatically to save power.
● A cassette holder can’t be opened unless a power supply is attached.
● There may be a delay after you press EJECT until the holder opens. Do not use force.
● The tape’s remaining time is displayed in the LCD monitor or the viewfinder as shown.
● The indicated remaining time is approximate.
● The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
● The tape remaining time indicator is correct only if the correct tape length has been selected (੬ pg. 12).
● “TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this condition
for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is loaded.
● While shooting, pressing DISPLAY lets you remove some indiations from the screen (੬ pg. 45).
● If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations, the
camcorder’s power shuts off automatically. Set the Power switch to “POWER OFF”, and then back to “CAMERA”
to turn the camcorder on again.
● If the Recording Start/Stop button is pressed after the Record-Standby mode has continued for over 5 minutes,
recording may not start immediately.
● If you’re recording on a cassette from the middle, use the RETAKE function (੬ pg. 19) to find the end of the last
recording so you don’t erase any of it.
● The LENS COVER warning blinks for about 5 seconds when the camcorder is turned on when the cover is closed.
● While shooting, sound is not heard from the speaker.
RECORDING Basic Recording (cont.)
16
EN
Shooting while watching the LCD monitor
Before the following steps, perform step 1 (੬ pg. 15).
ENTER RECORD–STANDBY MODE
LENS COVER
Switch
Make sure the LCD monitor is fully open. Slide the
2
LENS COVER open/close switch to open the lens
cover, then set the power switch to CAMERA.
•The power indicator lights and the camcorder
enters the Record–Standby mode.
•The scene you’re aimed at appears in the LCD
monitor, with the word “PAUSE” superimposed
upon it.
POWER
Start/Stop
Power indicator
START SHOOTING
Tilt the LCD monitor upward/downward for best
viewability (੬ pg. 17) and press the Recording
Start/Stop button.
3
4
MONITOR
OPEN
•The tally lamp lights while recording is in progress,
and “REC ” appears in the LCD monitor.
STOP RECORDING
Press the Recording Start/Stop button again to stop
recording.
•The camcorder re-enters the Record-Standby
mode.
Tape remaining time indicator
25min
*---min
NOTES:
(Now calculating)
●
When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, we recommend that you use the viewfinder
(੬ pg. 15).
120min
119min
●
For other notes, refer to pg. 15.
3min
2min (Blinking)
1min (Blinking)
0min (Blinking)
Tally lamp
EN
17
Journalistic shooting
In some situations different angles of shooting may be
required for more dramatic results.
OPEN LCD MONITOR
Make sure the LCD monitor is fully open.
1
TILT LCD MONITOR
Tilt the LCD monitor in the most convenient
2
direction.
•The LCD monitor can rotate almost full circle
(270°: 90° downward, 180° upward).
Self-recording
You can shoot yourself while viewing your own image in
the LCD monitor.
TILT LCD MONITOR UPWARD
Open the LCD monitor and tilt it upward to 180
1
2
degrees so that it faces forward.
START RECORDING
Point the lens toward yourself and start recording.
•During self-recording, the monitor image and
indications do not appear inverted as when
viewing a mirror.
Brightness control
You can adjust the brightness of the LCD monitor by
turning the BRIGHT dial.
ADJUST BRIGHTNESS
If you want to brighten the image...
1
Turn the dial toward “+”.
If you want to darken the image...
Turn the dial toward “–”.
BRIGHT dial
RECORDING Basic Features
18
EN
FEATURE:
Zooming
PURPOSE:
To produce the zoom in/out effect, or
an instantaneous change in image
magnification.
Zoom-in
OPERATION:
36X Hyper zoom
Digital circuitry doubles the
maximum 18x magnification offered
by optical zoom.
Zoom-out
1) To zoom in, slide the Zoom Lever
toward “T”.
2) To zoom out, slide toward “W”.
NOTES:
● During Hyper Zoom, the speed
increases the further you slide the
Zoom Lever.
Zoom indicator
bar
● Focusing may become unstable
during Hyper Zoom. In this case,
set the zoom while in Record–
Standby, set manual focus or Focus
Lock (੬ pg. 22, 23), then zoom in
or out in Record mode.
Zoom Level
indicator
● The Zoom Level Indicator (5) only
moves during optical zoom. Once
the Zoom Level indicator reaches
the top of the zoom indicator bar,
all magnification from that point is
through digital processing.
Power zoom lever
● During digital image processing,
the quality of the image may suffer.
EN
19
RETAKE (R/F)
FEATURE:
PURPOSE:
Quick Review
To check the end of the last
recording.
OPERATION:
1) Press “ ” and release quickly
during the Record–Standby mode.
•Tape is rewound for about 2
seconds and played back
automatically, then pauses in
Record–Standby mode for the
next shot.
NOTE:
Distortion may occur at start of
playback. This is normal.
FEATURE:
Retake
PURPOSE:
OPERATION:
To re-record certain segments.
1) Make sure the camcorder is in the
Record–Standby mode.
2) Press either RETAKE button to
reach the start point for new
recording. Pressing “F” forwards
the tape and pressing “R” reverses
it.
3) Press Recording Start/Stop to start
recording.
NOTE:
Noise may appear during Retake.
This is normal.
RECORDING Advanced Features
20
EN
Program AE With Special Effects
1 second later, the mode is activated.
All you have to do to access any of the variety of
After 1 sec.
shooting effects is to turn the PROGRAM AE select dial.
Sepia
SELECT MODE
Turn the PROGRAM AE select dial until the symbol
1
of the function you want is aligned with the mark.
LCD monitor or
viewfinder
•The selected mode’s name and its indication are
displayed in the LCD monitor or the viewfinder for
approx. 1 second. Then the name disappears, and
only the indication remains. The mode is activated.
•When Auto Mode Lock or Auto Mode Release
mode is selected, only the mode’s name is
displayed. Then the name disappears and the
mode is activated.
NOTES:
● Only one effect can be engaged at a time.
● The screen becomes slightly reddish when the Fade/
Wipe (੬ pg. 25) is used in the Sepia mode.
● The screen becomes slightly dark in the High Speed
Shutter mode. Use in well-lighted situations.
● In the High Speed Shutter or Sports modes, picture
color may be adversely affected if subject is lit by
alternating discharge-type light sources such as
flourescent or mercury-vapor lights.
Mark
C
U
PROGRAM AE
select dial
EN
21
Dial
LCD monitor/
Dial
LCD monitor/
Mode
Auto Mode Lock
Mode
symbol Viewfinder indication
symbol Viewfinder indication
LOCK
Auto Lock
Twilight
Twilight
Auto Mode Lock
Twilight
Locks the camcorder in Full Auto mode, preventing
incorrect operation due to accidental button
pressing during shooting.
Dusk, twilight scenery, fireworks, etc., look more
natural and dramatic. The following happens when
Twilight mode is selected:
•In this mode the following controls are disabled;
Fade/Wipe, Wide, Title, Display, M.W.B. (Manual
White Balance), Manual Focus, Focus Lock,
Exposure Control and MENU
•Auto gain control is turned off.
•White Balance is set to “ ” (outdoor mode), but
can also be manually changed to another mode
(੬ pg. 29).
•Auto Focus becomes available only in the range of
10 m to infinity. To focus when the subject-to-
camera distance is less than 10 m, use manual
focusing (੬ pg. 23).
RELEASE Auto Release
Auto Mode Release
Auto Mode Release
Re-enables the controls that were disabled by Auto
Mode Lock.
Sports
Sports
Sports
FG
FG : Fog
Electronic Fog Filter
High shutter speed clearly captures fast-moving
action.
Electronic Fog Filter
Makes the picture look misty white, as when an
external fog filter is attached to the lens. Softens the
image and gives it a “fancy“ look.
1/1000 sec.
1/1000
1/2000
S 1/1000
S 1/2000
1
High Speed Shutter
1/2000 sec.
2
High Speed Shutter
ND
ND : ND Effect
ND Effect
High-Speed Shutter (1/1000s., 1/2000s.)
Captures faster action than Sports mode.
ND Effect
A black mist darkens the picture, as when an ND
filter is used. Helps to counter the effects of glare on
the subject.
Sepia
Sepia
Sepia
The scene being shot is recorded in sepia-tinted
(reddish-brown) monochrome, giving the effect of
an older movie. Use together with Wide (੬ pg. 26)
for the authentic look of a classic Hollywood
movie.
RECORDING Advanced Features (cont.)
22
EN
Focusing
Auto Focus
The camcorder’s Full Range AF system offers continuous
shooting ability from close-up to infinity. However,
correct focus may not be obtainable in the situations
listed below (in these cases use manual focusing):
•When two subjects overlap in the same scene.
•When illumination is low.*
Focus
detection zone
NEAR
•When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-color wall,
or a clear, blue sky.*
•When a dark object is barely visible in the viewfinder.*
•When the scene contains minute patterns or identical
patterns that are regularly repeated.
FAR
•When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
•When shooting a scene with a high-contrast
background.
* The low-contrast warning “
monitor or the viewfinder.
” appears in the LCD
Focus Lock
This feature locks the focus in place, which is especially
helpful in the following situations:
•When things pass between your subject and the
camcorder. Engage the focus lock function to lock your
subject in before recording.
•When you want your subject to be focused, and to
appear in a corner of the screen. First, center on the
subject and focus using auto focus mode. Then engage
the focus lock function and move the camcorder until
the subject is where you want it.
PROGRAM AE select dial
SELECT MODE
Turn the PROGRAM AE select dial to any position
1
2
3
except AUTO LOCK.
LOCK FOCUS
NOTES:
Press FAR or NEAR. The focus lock indication “
appears in the LCD monitor or the viewfinder.
”
● If the lens is smeared or blurred, accurate
focusing is not possible. Keep the lens clean,
wiping with a piece of soft cloth if it gets
dirty. When condensation occurs, wipe with
a soft cloth or wait for it to dry naturally.
● When shooting a subject close to the lens,
zoom-out first (੬ pg. 18). If zoomed-in in
the auto focus mode, the camcorder could
automatically zoom out depending on the
distance between the camcorder and the
subject. *When Tele Macro (੬ pg. 31) is
activated, the camcorder will not zoom out
automatically.
RELEASE FOCUS LOCK
Press FAR and NEAR simultaneously. The focus lock
indication disappears.
EN
23
Manual Focus
NEAR
FAR
NOTE:
You should already have made the necessary viewfinder
adjustments (੬ pg. 10). If you haven’t, do so before
continuing.
SELECT MODE
Power zoom lever
Turn the PROGRAM AE select dial to any position
1
2
except AUTO LOCK.
ADJUST FOCUS
To farther subject . . .
Press and hold FAR. The Manual Focus indications
“
” appear and “ ” blinks.
Go to step 3.
To nearer subject . . .
Press and hold NEAR. The Manual Focus indications
PROGRAM AE select dial
“
” appear and “ ” blinks.
Go to step 3.
LOCK FOCUS
Release FAR or NEAR. The focus indication is
3
4
replaced by the focus lock indication
“
” and the adjusted focus is locked in.
RELEASE MANUAL FOCUS MODE
Press FAR and NEAR simultaneously. The Manual
Focus mode is immediately released and the focus
lock indication disappears.
NOTES:
● Be sure to focus the lens in the maximum telephoto
position when you use the Manual Focus mode. If you
focus in on a certain subject in the wide-angle position,
sharply focused images cannot be obtained when
zoomed up because the depth-of-field is reduced at
longer focal lengths.
● When the focus level cannot be adjusted any farther or
closer, “ ” or “ ” will blink.
RECORDING Advanced Features (cont.)
24
EN
Picture Stabilizer
This feature compensates for unstable images caused by
camera-shake, particularly noticeable at high magnifica-
tion.
ACTIVATE PICTURE STABILIZER
Press PICTURE STABILIZER. “ ” appears in the
1
LCD monitor or the viewfinder.
PICTURE STABILIZER
•To switch off the Picture Stabilizer, press PICTURE
STABILIZER. The indicator disappears.
NOTES:
● Accurate stabilization may not be possible if hand
shake is excessive, or under the following conditions:
• When shooting subjects with vertical or horizontal
stripes
• When shooting dark or dim subjects
• When shooting subjects with excessive backlighting
• When shooting scenes with movement in various
directions
• When shooting scenes with low-contrast
backgrounds
● Switch off Picture Stabilizer when recording with the
camcorder on a tripod.
Exposure Control
This feature automatically adjusts the iris for the best
available picture quality, but you can override and make
the adjustment manually.
SELECT MODE
Turn the PROGRAM AE select dial to any position
1
2
except AUTO LOCK.
BRIGHTEN IMAGE
Press + (maximum +06). The Exposure level
indicator appears in the LCD monitor or the
viewfinder.
+
02
OR . . .
LCD monitor or viewfinder
Exposure Level Indicator
DARKEN IMAGE
Press – (maximum –06). The Exposure level
indicator appears in the LCD monitor or the
viewfinder.
To brighten the image
When you want to return to the factory setting . . .
RESTORE INITIAL SETTING
Press + and – simultaneously. The standard setting is
immediately restored and the Exposure level
indicator disappears.
–
06
+
06
3
To darken the image
EN
25
Fade/Wipe
[Ex. : Black Fader]
These effects let you make pro-style scene transitions.
Fade- or wipe-in works at recording start, and fade- or
wipe-out works at recording end or when you enter
Record–Standby mode.
FADE IN
SELECT MODE
Turn the PROGRAM AE select dial to any position
FADE OUT
1
2
except AUTO LOCK.
Function indication
SELECT FUNCTION
LCD monitor or
viewfinder
Press SEL. repeatedly until “
” appears.
Fade/Wipe
Fade/Wipe
Mosaic Fader
After 2 sec.
ENGAGE FADE- OR WIPE-
STANDBY MODE
Fade/Wipe
Press SET to cycle through the modes as shown at
left. Once the desired mode appears, it is selected
and reserved.
3
BK
•The selected mode’s name and its indication are
displayed in the LCD monitor or the viewfinder for
approx. 2 seconds. Then the name disappears, and
only the indication remains.
BK
Black Fader
Mosaic Fader
Shutter Wipe
Slide Wipe
START RECORDING
Off
Press Recording Start/Stop to start recording and
activate fade- or wipe-in.
(No indication)
4
OR . . .
OFF
END RECORDING
Press Recording Start/Stop to end recording and
engage fade- or wipe-out.
TO CANCEL FADE- OR WIPE-
STANDBY MODE
SET button
SEL. button
While “
” is displayed, press SET twice.
Fade/Wipe
5
•“OFF” is displayed for approx. 2 seconds and the
reserved fade or wipe is cancelled.
B
K
Black Fader
Fades in/out to a black screen.
Mosaic Fader
Gradually turns/returns the picture into/from a mosaic
pattern.
PROGRAM AE select dial
Shutter Wipe
NOTES:
A black screen moves in from the top and bottom,
closing over the image like a shutter, or a new image
pushes open the black screen vertically from the center.
● Pressing and holding the Recording Start/
Stop button allows you to record a black
blank screen, or a mosaic pattern if Mosaic
Fader is selected.
Slide Wipe
●
The screen becomes slightly reddish when
the Fade/Wipe is used with Sepia ( pg. 21).
A black screen moves in from the left to gradually cover
the image, or a new image moves in from right to left.
੬
RECORDING Advanced Features (cont.)
26
EN
Wide
LCD monitor or viewfinder
This feature allows you to record black bars at the top
and bottom of the screen to produce a cinema-like
“wide-screen” effect.
SELECT MODE
Turn the PROGRAM AE select dial to any position
Wide mode
1
2
3
4
except AUTO LOCK.
SELECT FUNCTION
LCD monitor or
viewfinder
Title
Press SEL. repeatedly until “
” appears.
Wide
ENGAGE WIDE MODE
PressSET.
Title indication
No indication
Happy Birthday
Our Vacation
RESTORE NORMAL SCREEN
Press SET again while “ Wide” appears.
Merry Christmas
A Special Day
Happy Holidays
Our New Baby
Wedding Day
Congratulations
Instant Titles
The camcorder has eight preset titles in memory. You can
superimpose one of them above a previously stored title as
shown in the illustration to the left.
DISPLAY
SELECT MODE
Turn the PROGRAM AE select dial to any position
The characters you have set
using Character Generator
1
2
3
except AUTO LOCK.
SELECT FUNCTION
SET button
Press SEL. repeatedly until “
” appears.
Title
SELECT PRESET TITLE
Engage the Record–Standby mode, then press SET to
cycle through the preset titles until the desired title is
displayed.
SEL. button
NOTES:
● To delete the Instant Title during recording, press SEL.
repeatedly until “
” appears then press SET.
Title
● To recall a title, press SET again.
PROGRAM AE select dial
EN
27
Character Generator
MENU button
FAR
You can enter an original title of up to 18 characters.
NEAR
ACCESS MENU SCREEN
Turn the PROGRAM AE select dial to any position
1
2
except AUTO LOCK, then press MENU.
ACCESS CHARACTER SET MENU
Press + or – to move the highlight bar to “Set
Character”, then press NEAR. The Character Set
menu appears.
INPUT CHARACTERS
Press +, –, FAR or NEAR to make the desired
character blink, then press MENU. The selected
characters appear at the bottom of the screen.
Repeat as many times as desired (max. 18).
3
•To select the location of the next character, press
+, –, FAR or NEAR to make the row of squares
blink at the bottom of the screen, then press FAR
or NEAR to move the blinking cursor underneath
the desired location. Press + when you’re done,
and the blinking cursor returns to the character
grid.
PROGRAM AE select dial
LCD monitor or viewfinder
Gain Up
S.LX
OFF
OFF
OFF
07
Tele Macro
Interval Timer
Rec Time
END CHARACTER SETTING
Press +, –, FAR or NEAR to make “End” blink, then
JLIP ID NO.
Tally
4
press MENU twice to return to the normal screen.
ON
Set Character
Date/Time
NOTES:
END :MENU KEY
● To erase a character you entered mistakenly, make
“Clear” blink by pressing +, –, FAR or NEAR, then press
MENU. All characters are deleted at once. Or, to erase
selected characters only, first move the blinking cursor
to the character at the bottom row which you want to
replace, then press +, FAR or NEAR to highlight “ ” in
the top left corner, and then press MENU.
● To display the characters you have set — “Instant Title”
(੬ pg. 26) or “Date/Time/Character Insert”
(੬ pg. 28).
SET : MENU KEY
A
K
U
È
.
B
L
C
D
N
E
O
Y
F
P
Z
G
Q
Ä
H
R
Ö
I
J
T
À
:
M
S
V W X
Ü
&
ࡖ 9
Ò
,
Ì
Ù
Ñ Æ Ø
Å
¿
–
’
/
!
?
0 1 2 3 4 5 6 7 8
I
L I
● Characters may be set only in the Record-Standby
mode.
End
Clear
SET : MENU KEY
A
B
L
C
D
N
E
O
Y
F
P
Z
G
Q
Ä
H
R
Ö
I
J
T
À
:
K
U
È
.
M
S
V W X
Ü
&
ࡖ 9
Ò
,
Ì
Ù
Ñ Æ Ø
Å
¿
–
’
/
!
?
0 1 2 3 4 5 6 7 8
I
L I KE YOU
ࡖ End
Clear
RECORDING Advanced Features (cont.)
28
EN
Date/Time Character Insert
This feature allows you to display date, time and characters
in the LCD monitor or the viewfinder and on a connected
color monitor, record them manually or automatically, and
even make your own titles.
SET
SEL.
NOTE:
You should already have performed the Date/Time
Setting procedure (੬ pg. 11). If you haven’t, do so
before continuing.
DISPLAY
LCD monitor
SELECT MODE
or viewfinder
Turn the PROGRAM AE select dial to any position
1
2
3
except AUTO LOCK.
Disp.
PROGRAM AE
select dial
SELECT DISPLAY
Press SEL. repeatedly until “ Disp.” appears.
CHOOSE DISPLAY MODE
Date/Time display
Date display
Time display
Press SET while in Record–Standby to cycle through
the modes as shown in the illustration at left.
Date-off mode
(No indication)
Auto Date Record
mode
The characters you have set using Character
Generator
NOTES:
● The selected display can be recorded.
● If you don’t want to record the display, select Date-off
mode before shooting.
Date display
Auto Date Record mode
● If you want to delete the display during shooting, press
SEL. repeatedly until “ Disp.” appears then press SET.
● To recall the display, press SET again.
AUTO DATE RECORD
DEC 25.97
Auto Date
Your camcorder automatically records the date for about
5 seconds after recording is initiated in the following
situations:
Auto date record mode
Time display
•After changing the date.
•After loading a cassette.
•After Auto Date Record mode is selected by pressing
SET.
DEC 25.97
In this mode, the date is replaced after 5 seconds with
“Auto Date”.
PM10:50:00
Auto date record
executed
Date/Time display
Characters
NOTES:
● Setting PROGRAM AE to LOCK always engages the
Auto Date Record mode, and disables all other modes.
● In the Auto Date Record mode, if the date changes
while you’re shooting, the date indication is recorded
for about 5 seconds from that point. It is not recorded
during any other recordings made on that day.
DEC 25.97 PM10:50:00
I LIKE YOU
ࡖ Example of stored
characters
EN
29
Manual White Balance Adjustment
(M.W.B.)
This camcorder’s Automatic Color Temperature system
senses the color temperature of the ambient lighting for
automatic white balance adjustment. However, precise
color adjustment is not possible under the following
conditions:
SET
SEL.
•When an object is in various shades of the same color.
•When a predominantly red or brown object is being
shot outdoors.
In these cases, use the camcorder’s built-in preset filters
for white balance adjustment.
LCD monitor
SELECT MODE
or viewfinder
Turn the PROGRAM AE select dial to any position
1
2
3
except AUTO LOCK.
M.W.B.
PROGRAM AE
select dial
MWB
SELECT FUNCTION
Press SEL. reapeatedly until “
” appears.
M.W.B.
No indication
MWB
(Auto)
SELECT WHITE BALANCE
White balance
mode indicator
Press SET (Manual White Balance) until the
required indication appears in the LCD monitor or
the viewfinder.
“MWB” .... With a memorized personal White
Balance setting (see below)
“
“
“
” ......... Outdoors on sunny day
” ........Outdoors on cloudy day
” ......... Light source is halogen or tungsten lamp
MWB
MWB sets the color temperature for the subject’s light
source so you can shoot with natural colors that are
unaffected by surroundings, even when there are
multiple subjects with different color temperatures.
NOTES:
● To switch to automatic white balance
adjustment, press SET until the indication
disappears, or turn the PROGRAM AE select
dial to “AUTO LOCK”.
SELECT MODE
Turn the PROGRAM AE select dial to any position
1
2
except AUTO LOCK.
● Re-adjust the White Balance when the
lighting has changed, when the camcorder
has been turned off and on again, or when
the PROGRAM AE select dial’s position has
been changed.
ADJUST FOCUS
Point the camcorder at a white, flat object such as a
sheet of white paper, and adjust focus manually
(੬ pg. 23).
● When adjusted by putting colored paper in
front of the subject in step 2 (“ADJUST
FOCUS”), this unit makes its color tempera-
ture standard for automatic white balance.
So you can enjoy shooting with different
colors. For example, when adjusting with
red, blue or yellow colors, the image
becomes the color which aproximates to
green, orange or purple respectively.
ADJUST WHITE BALANCE
Press SET until “MWB” appears, then press and hold
3
SET for more than 3 seconds.
•“MWB” blinks in the LCD monitor or the view-
finder during adjustment, then stops blinking but
stays lit when adjustment is complete.
RECORDING Advanced Features (cont.)
30
EN
Using Menu For Detailed Adjustment
MENU
FAR
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of the more
detailed camcorder settings.
NEAR
SELECT MODE
Turn the PROGRAM AE select dial to any position
1
2
3
4
except AUTO LOCK.
ACCESS MENU SCREEN
Press MENU.
SELECT FUNCTION
Press + or – to place the highlight bar on the desired
function.
MAKE SETTING
The setting procedure depends on the function you
select.
PROGRAM AE select dial
LCD monitor or viewfinder
If you select Gain Up, Tele Macro, Interval Timer,
Rec Time, JLIP ID NO or Tally. . . .
.... press FAR or NEAR to cycle through the choices
until the desired setting appears.
If you select Set Character or Date/Time, . . .
.... press NEAR to access the selection menu for
each function (Set Character – ੬ pg. 27; Date/
Time – ੬ pg. 11).
Gain Up
S.LX
OFF
OFF
OFF
07
Tele Macro
Interval Timer
Rec Time
JLIP ID NO.
Tally
Set Character
Date/Time
ON
END :MENU KEY
CLOSE MENU
Press MENU. The normal screen reappears.
5
Gain Up
NORM
ON
Tele Macro
Interval Timer
Rec Time
1min
1/2s
07
NOTE:
JLIP ID NO.
Tally
Set Character
Date/Time
The menu is available only in the Record-Standby mode.
ON
END :MENU KEY
PAUSE
If GAIN UP or TELE MACRO in the Menu has
been changed from the factory settings, this
mark appears.
EN
31
MENU
Gain Up
S.LX
To record a subject in a dark lit environment. When it is more
convenient to shoot the subject with a brighter image even if
the picture becomes slightly coarse. Automatically selected
when the PROGRAM AE select dial is set to AUTO LOCK
mode. (S.LX : Super LoLux)
NORM
To record a subject in a dimly lit environment. When it is
more convenient to shoot with a less coarse picture although
the subject becomes slightly dark. This setting is suitable for
measuring sensitivity conforming to EIA-639 (EIA* Standard
for Low Light Sensitivity Measurement)
*EIA : Electronic Industries Association
OFF
Allows you to shoot dark scenes with no picture brightness
adjustment.
Tele Macro
OFF
ON
Usually set to this position.
Usually the distance to a subject where the lens is in focus
depends on the zoom magnification. Unless there is a
distance more than 1m to the subject, the lens is out of focus
at the maximum telephoto setting. When set to “ON”, you
can shoot a subject as large as possible at a distance of
approx. 60 cm.
•Depending on the zoom position, the lens may go out of
focus.
OFF
15s
30s
1min
5min
OFF
1/4s
1/2s
1s
Interval Timer
Rec Time
This feature allows you to set the parameters for Self-Timer
(੬ pg. 32) and Time-Lapse recording (੬ pg. 33).
This feature allows you to set the parameters for Animation
and Time-Lapse recording (੬ pg. 33).
5s
JLIP ID NO.
Tally
This number is necessary when connecting the camcorder to a device such
as a computer using the J terminal (JLIP).
The numbers range from 01 to 99. Factory setting is 07.
ON
The tally lamp comes on to signal the start of rcording.
The tally lamp remains off at all times.
OFF
Set Character
Date/Time
Allows you to input characters. (੬ pg. 27).
Allows you to set the current date and time (੬ pg. 11).
= Factory setting and when the PROGRAM AE Select Dial is set to AUTO LOCK
NOTE:
During shooting in low light, Auto Focus accuracy may decrease even when Gain Up is used. In this case,
use Manual Focus (੬ pg. 23).
RECORDING Advanced Features (cont.)
32
EN
Self-Timer
MENU
FAR
You can set the delay between pressing the Recording
Start/Stop button and the actual start of recording. If you
secure the camcorder, you (or whomever is operating the
camcorder) can enter the scene before recording starts.
NEAR
NOTE:
Make sure the camcorder is in the Record-Standby mode
before performing the following steps.
ACCESS MENU SCREEN
Turn the PROGRAM AE select dial to any position
1
2
except AUTO LOCK, then press MENU.
SET INTERVAL TIME
Press – or + to move the highlight bar down to
“Interval Timer”, then press FAR or NEAR to cycle
through the choices. Stop when the desired time
appears. Choose from “15s”, “30s”, “1min”, “5min”,
or select to turn the function “OFF”.
PROGRAM AE select dial
CLOSE MENU
Press MENU.
3
4
START DELAYED RECORDING
Press the Recording Start/Stop button. The tally lamp
begins blinking, and the blinking frequency
increases about 5 seconds before recording is to
start. Once recording begins, the lamp stops
blinking but stays lit.
Tally lamp
Interval Timer Indicator
To Release Self-Timer . . .
..... while the tally lamp is blinking, press the Recording
Start/Stop button to stop the blinking, then set
“Interval Timer” to “OFF”.
Rec Time Indicator
1min
1/2s
LCD monitor or viewfinder
Gain Up
S.LX
OFF
OFF
OFF
07
Tele Macro
Interval Timer
Rec Time
JLIP ID NO.
Tally
ON
Set Character
Date/Time
END :MENU KEY
5s
1s
1/2s
1/4s
OFF
5min
1min
30s
15s
OFF
EN
33
Animation
Time-Lapse
Give stationary scenes or objects an illusion of
movement. This function allows you to shoot a
series of pictures, each slightly different, of the same
object for a brief period of time.
You can record sequentially at preset time spans.
Leaving the camcorder aimed at a specific subject,
you can record subtle changes over an extended
period of time.
NOTE:
NOTE:
Make sure the camcorder is in the Record-Standby
mode and the recording mode is set to “SP” before
performing the following steps.
Make sure the camcorder is in the Record-Standby
mode and the recording mode is set to “SP” before
performing the following steps.
ACCESS MENU SCREEN
ACCESS MENU SCREEN
Turn the PROGRAM AE select dial to any
Turn the PROGRAM AE select dial to any
1
2
position except AUTO LOCK, then press
MENU.
1
2
position except AUTO LOCK, then press
MENU.
SET RECORDING TIME
SET INTERVAL BETWEEN
Press – or + to move the highlight bar down to
“Rec Time”, then press FAR or NEAR to cycle
through the choices. Stop when the desired
time appears. Choose from “1/4s”, “1/2s”,
“1s”, “5s”, or select to turn the function “OFF”.
Then press MENU to close Menu screen.
RECORDINGS
Press – or + to move the highlight bar down to
“Interval Timer”, then press FAR or NEAR to
cycle through the choices. Stop when the
desired time appears. Choose from “15s”,
“30s”, “1min”, “5min”, or select to turn the
function “OFF”.
START RECORDING
Press the Recording Start/Stop button after
focusing on the subject. The recording stops
automatically after the selected period of time.
SET RECORDING TIME
3
Press – or + to move the highlight bar down to
“Rec Time”, then press FAR or NEAR to cycle
through the choices. Stop when the desired
time appears. Choose from “1/4s”, “1/2s”,
“1s”, “5s”, or select to turn the function “OFF”.
Then press MENU to close Menu screen.
3
ASSEMBLE SERIES OF
PICTURES
Repeat step 3 for the desired number of
pictures.
4
5
START TIME-LAPSE
RELEASE ANIMATION MODE
RECORDING
Set “Rec Time” in the Menu screen to “OFF”.
Press the Recording Start/Stop button.
Recording and intervals alternate
automatically.
4
5
NOTES:
RELEASE TIME-LAPSE MODE
To release when the tally lamp is not blinking,
set “Rec Time” and “Interval Timer” in the
Menu screen to “OFF”. To release when the
tally lamp is blinking, press the Recording
Start/Stop button to stop the blinking, then set
“Interval Timer” and “Rec Time” in the Menu
screen to “OFF”.
● For best results, make sure the camcorder is
secured when shooting in Animation or
Time-Lapse mode.
● Fade/Wipe-in/out cannot be performed during
Animation or Time-Lapse shooting.
● Before performing other operations following
Animation or Time-Lapse recording, make sure
the Animation or Time-Lapse mode is deactivated.
PLAYBACK Basic Playback
34
EN
LOAD A CASSETTE
First slide MONITOR OPEN and open the LCD
monitor to an angle of over 45 degrees. Press EJECT
to open the cassette holder, then insert the cassette
with the label facing out. Press PUSH to ensure the
holder is closed and locked.
1
2
SELECT MODE
Make sure the LCD monitor is fully open. Then set
the power switch to PLAY. The Power On indicator
lights.
POWER
PLAYBACK
PLAY/PAUSE
Press PLAY/PAUSE. The playback picture appears in
FF
STOP DISPLAY
3
4
the LCD monitor.
STOP PLAYBACK
Press STOP.
REW
Rewind or Fast-forward the tape
Press REW to rewind, or FF to fast-forward the tape
Speaker
during Stop mode.
Adjust the brightness of the LCD monitor
To brighten the image, turn the BRIGHT dial toward “+”.
To darken the image, turn the dial toward “–”.
Speaker volume control
You can adjust the speaker volume by turning the
VOLUME dial.
BRIGHT
VOLUME
ADJUST VOLUME
Recording mode indicator
If you want to turn up the volume...
1
Turn the dial toward “+”.
If you want to turn down the volume...
Turn the dial toward “–”.
Tape running indicator
SP
M-1:23:45
4
3
: Playback
: Fast-Forward/
Forward Search
: Rewind/Reverse
Search
NOTES:
2
● The camcorder shuts off automatically after about 5
minutes in Stop mode. To turn on again, set the power
switch to POWER OFF, then to PLAY.
6 : Still Playback
8 : Eject
Tape counter
● When the power switch is set to CAMERA and the LCD
monitor is opened at an angle of 45 degrees or more,
the LCD monitor switches on and the viewfinder
switches off automatically to save power.
● When the LCD monitor is turned off, sound is not
heard from the speaker.
LCD Monitor in Retracted Position
● The playback picture can also be viewed in the
viewfinder (with the LCD monitor shut) or on a
connected TV (੬ pg. 36). Camcorder operation is the
same as described in this section.
● You can also view the playback picture on the LCD
moitor with it flipped over and retracted.
● During playback, pressing DISPLAY lets you remove all
indications from the screen.
PLAYBACK Features
EN
35
FF STOP
FEATURE:
PURPOSE:
Manual Tracking
To eliminate noise bars that appear
on the screen during playback.
OPERATION:
NOTES:
1) Press either +/– button as many
times as necessary for best picture.
● To reset TRACKING to the original
preset, press both + and – buttons
simultaneously.
REW
PLAY/PAUSE
COUNTER R/M
● Manual Tracking may not work
with tapes recorded on other VCRs
or camcorders.
FEATURE:
Still Playback
PURPOSE:
OPERATION:
To pause during playback.
1) Press PLAY/PAUSE during
playback.
2) To resume normal playback, press
PLAY/PAUSE again.
NOTE:
Noise bars appear and pictures may
become monochrome during Still
Playback. This is normal.
FEATURE:
PURPOSE:
Shuttle Search
To allow high-speed search in either
direction.
OPERATION:
Forward Search
1) Press FF during playback.
Reverse Search
1) Press REW during playback.
NOTE:
Noise bars appear and pictures may
become monochrome or darken in
Shuttle Search. This is normal.
FEATURE:
PURPOSE:
Counter Memory Function
To make it easier to locate a specific
tape segment.
OPERATION:
1) Press COUNTER R/M and hold for
more than 2 seconds. The counter
resets to “0:00:00”.
2) Press COUNTER R/M. “M”
appears.
3) After recording or playback, press
STOP, then REW. The tape
automatically stops at or close to
0:00:00.
4) Press PLAY/PAUSE to start
playback.
NOTES:
● The counter memory functions in
the Fast-Forward and Rewind
modes.
● To disable Counter Memory
Function, press COUNTER R/M
less than 1 second so the “M”
disappears.
PLAYBACK Basic Connections
There are three basic types of connections. When making
the connections, refer also to your VCR and TV
instruction manuals.
36
EN
Connection To A VCR [A]
(Editing, Dubbing and Playback)
NOTE:
Use the optional Audio and Video cables.
To AUDIO and
When
VIDEO connectors
CONNECT CAMCORDER TO VCR
connecting the
cables, open
As shown in the illustration at left, connect the
Audio and Video
cables (optional)
1
Audio and Video cables between the AUDIO and
VIDEO connectors on the camcorder and those on
the VCR.
the jack cover.
SUPPLY POWER
A
B
Turn on the camcorder, the VCR and the TV.
To AUDIO and
VIDEO IN
connectors
2
3
SELECT MODE
Set the VCR to its AUX input mode, and set the TV
to its VIDEO mode.
VCR
Antenna
Connection To A TV With A/V Input
Connectors [B] (Playback ONLY)
NOTE:
Use the optional Audio and Video cables.
CONNECT CAMCORDER TO TV
To AUDIO,
VIDEO and RF DC
OUT connectors
As shown in the illustration at left, connect the
1
2
Audio and Video cables between the AUDIO and
VIDEO connectors on the camcorder and those on
the TV.
RF unit RF-V5U
(optional)
SELECT MODE
Set the TV to its VIDEO or AV mode (as specified in
its instructions).
NOTES:
● It is recommended to use the AC Power
Adapter/Charger as the power supply instead
of the battery pack.
● To monitor the picture and sound from the
camcorder without inserting a tape, set the
camcorder’s Power switch to “CAMERA”,
then set your TV to the appropriate input
mode.
● If you have a TV or speakers that are not
specially shielded, do not place the speakers
adjacent to the TV as interference will occur
in the camcorder playback picture.
Connection To A TV With NO A/V Input
Connectors (Playback ONLY)
NOTE:
Use the optional RF-V5U RF unit.
* Refer to the RF-V5U instruction manual for connection
procedure.
PLAYBACK Using The Cassette Adapter
Cassette Adapter (VHS PlayPak)
EN
37
Use this to play back a VHS-C video cassette recorded
with this camcorder. It is fully compatible with any VHS
video cassette recorder. The C-P7U adapter is battery
powered and automatically performs tape loading and
unloading.
+
INSERT BATTERY
Slide the battery cover up to remove it, and install
one “AA(R6)” size battery as shown in the
illustration at left. Then reattach the cover.
1
2
3
VCR
INSERT CASSETTE IN ADAPTER
Slide the latch to open the adapter compartment
door, then insert the cassette and close the
compartment door.
Compartment door
PLAY BACK ON CONNECTED VCR
Load the cassette adapter into the VCR and play the
tape back as you would any other.
REMOVE CASSETTE FROM
ADAPTER
Slide the latch and the compartment door opens
automatically. Then insert your finger in the hole on
the underside of the adapter as shown in the
4
Sliding latch
Reels
illustration at left, push up and remove the cassette.
Compact video cassette
NOTES:
● During tape loading and unloading, do not touch the
reels for safety and tape protection.
● During special-effect playback (slow motion, still
frame, etc.), the picture may vibrate or noise bars may
appear on the screen.
● To record on a VCR using a compact cassette and the
adapter, cover the adapter’s recording safety hole with
adhesive tape.
Recording safety hole
EDITING
38
EN
Tape Dubbing
PLAY/PAUSE
CONNECT EQUIPMENT
Following the illustration at left, connect the
camcorder and the VCR.
1
2
PREPARE FOR DUBBING
Set the camcorder’s Power switch to “PLAY”, turn
on the VCR’s power, and insert the appropriate
cassettes in the camcorder and the VCR.
SELECT VCR MODE
Engage the VCR’s AUX and Record-Pause modes.
3
4
FIND EDIT-IN POINT
Engage the camcorder’s Play mode to find a spot
just before the edit-in point. Once it’s reached, press
PAUSE on the camcorder.
To AUDIO and
VIDEO OUT
connectors
START EDITING
When connecting
the cables, open the
jack cover.
Press PLAY on the camcorder and engage the VCR’s
Record mode.
5
6
7
STOP EDITING TEMPORARILY
Engage the VCR’s Record-Pause mode and press
PAUSE on the camcorder.
Audio and Video
cable (optional)
EDIT MORE SEGMENTS
Repeat steps 4 through 6 for additional editing, then
stop the VCR and camcorder when finished.
To AUDIO and
VIDEO IN
connectors
VCR (Recording deck)
EN
39
SET REMOTE/VCR CODE
Random Assemble Editing
[R.A.Edit]
SET REMOTE TO OPERATE VCR
Create edited videos easily using your
camcorder as the source player. You can select
up to 8 “cuts” for automatic editing, in any
order you like. R.A.Edit is more easily
performed when the optional RM-V700U MBR
(Multi-Brand Remote) is set to operate with
your brand of VCR (see VCR CODE LIST), but
can also be performed by operating the VCR
manually.
Turn off the power to the VCR and point the remote
toward the VCR’s infrared sensor. Then, referring to
the VCR CODE LIST on the left, press and hold MBR
SET, and press button (A) and then (B).
1
2
•The code is automatically set once you release the
MBR SET button, and the VCR’s power comes on.
OPERATE THE VCR
Make sure the VCR’s power is on. Then, while
holding VCR CTL, press the button on the remote for
the desired function. The functions the remote can
control are PLAY, STOP, PAUSE, FF, REW and VCR
REC STBY (you don’t need to press VCR CTL for this
one).
You’re now ready to try Random Assemble Editing.
MBR SET
IMPORTANT
1
4
7
2
5
8
3
6
9
VCR CTL
Although the MBR is compatible with JVC VCRs and
those of many other makers, it may not work with yours
or may offer limited functions.
0
RM-V700U (optional)
NOTES:
● If the VCR’s power doesn’t come on in step 1, try
another code from the VCR CODE LIST.
● Some brands of VCR don’t come on automatically. In
this case, turn the power on manually and try step 2.
● If the RM-V700U is not able to control the VCR, use
the controls on the VCR.
VCR CODE LIST
VCR BRAND BUTTONS
VCR BRAND BUTTONS
NAME
(A) (B)
NAME
(A) (B)
GE
1
9
9
9
1ꢀ
2ꢀ
`ꢀ
4
PHILIPS
1
3
2ꢀ
3
● The RM-V700U cannot be used to operate this
camcorder.
PANASONIC
1
1
1
9
1
9
9
6
6
9
3ꢀ
7ꢀ
1ꢀ
4ꢀ
8ꢀ
2ꢀ
4ꢀ
6ꢀ
3ꢀ
`
MAKE CONNECTIONS
HITACHI
6
6
6ꢀ
3
CONNECT TO . . .
JVC
A
B
C
9
9
9
1ꢀ
6ꢀ
3
ꢀ
RCA
A
JVC VCR EQUIPPED WITH REMOTE
1
PAUSE TERMINAL
Connect the editing cable to the Remote PAUSE
terminal.
MAGNAVOX
9
1
7
7
5ꢀ
1ꢀ
1ꢀ
6
SANYO
SHARP
SONY
3
3
1
1
6
6
3
3
6
6
6ꢀ
5
5ꢀ
`
5ꢀ
`ꢀ
9ꢀ
1ꢀ
9ꢀ
1
B
JVC VCR NOT EQUIPPED WITH REMOTE
PAUSE TERMINAL
MITSUBISHI
NEC
6
6
7ꢀ
8
Connect the editing cable to the R.A.EDIT
connector.
3
3
7ꢀ
8
C
NON-JVC VCR WITH NEITHER
PHILIPS
1
9
1
9
9
9
9ꢀ
5ꢀ
1ꢀ
4ꢀ
1ꢀ
6
Connect the editing cable to the RM-V700U’s
Pause-In jack.
ꢀ
TOSHIBA
ZENITH
All other connections are as shown in the
illustration on page 40.
1
6
CONTINUED ON NEXT PAGE
EDITING (cont.)
40
EN
PREPARE CAMCORDER
Insert a recorded tape and set the Power switch to
“PLAY”.
2
3
PREPARE VCR
REW/FF
STOP
PLAY/PAUSE
IN/OUT
CANCEL
Turn the power on, insert a recordable tape and
engage the AUX mode (refer to VCR’s instructions).
R.A. EDIT
SELECT SCENES
ACCESS R.A. EDIT COUNTER
DISPLAY
Press PLAY/PAUSE, then press R.A. EDIT and the
counter display appears in the viewfinder and the
screen of the connected TV.
1
2
3
REGISTER BEGINNING OF SCENE
Press REW or FF to locate the beginning of a scene
you want, then press IN/OUT to register that point.
The data appears under “IN” on the display.
Open the cover
To AUDIO
and VIDEO
out connectors
To J terminal
(JLIP)
REGISTER END OF SCENE
Press REW or FF to locate the end of the scene and
press IN/OUT to register it. The data appears under
OUT on the display. The total time of the registered
scene(s) is displayed at the bottom of the screen.
Editing cable
(optional, ø3.5
mini-plug cable)
Audio and
Video cable
(optional)
REGISTER ADDITIONAL SCENES
Repeat steps 2 and 3 for each additional scene
(as many as 8).
4
5
A B
C
To Remote
PAUSE
MAKE CORRECTIONS
To AUDIO
and VIDEO IN
connectors
Press CANCEL during steps 2 and 3 to erase the
most recently registered point.
To Pause-In
VCR (Recording deck)
NOTES:
● There must be at least one second between an in-point
and its corresponding out-point.
RM-V700U
(optional)
● To ensure correct operation, leave at least 15 seconds
open between scenes.
● Blank portions of tape cannot be registered as in-points
or out-points.
VCR REC STBY
● If it takes more than 5 minutes to search for an in-point,
the VCR’s Record-Pause mode is cancelled and editing
doesn’t take place.
● Pressing R.A.EDIT clears all in- and out-points from
memory.
● Leave a small margin for error around each in-point to
ensure the scene is recorded in its entirety.
IN
OUT
IN
OUT
1
2
3
4
5
6
7
8
0:00:25
--:--:--
1
2
3
4
5
6
7
8
0:00:25
0:03:18
0:02:33
0:04:11
0:01:05
0:03:31
0:02:53
--:--:--
COUNTER
TOTAL
0:00:25
0:00:00
COUNTER
TOTAL
0:04:11
0:01:13
EN
41
AUTOMATIC EDITING TO VCR
ORIGINAL TAPE (camcorder)
1
IN
3
2
IN
ENGAGE VCR’S RECORD–PAUSE
MODE
OUT
IN OUT
OUT
Point the remote control toward the VCR’s infrared
sensor and press VCR REC STBY, or manually
engage the VCR’s Record-Pause mode.
1
2
BEGIN AUTOMATIC EDITING
Press EDIT on the camcorder, and the previously
selected scenes are copied to the VCR in the
specified order.
While editing, the R.A. Edit counter of the scene
which is beging copied is shown with a blinking
highlight.
EDITED TAPE (VCR)
STOP
END AUTOMATIC EDITING
When all selected scenes have been copied, the
camcorder and VCR enter the still or pause mode.
Press STOP on both units. To make the R.A. Edit
counter display disappear, press R.A.EDIT.
3
•When finished editing, be sure to disconnect the
editing cable and the audio/video cable.
NOTES:
C
● If you performed step 1
on page 39 (“MAKE
EDIT
R.A. EDIT
CONNECTIONS”), keep the remote control pointed at
the VCR during editing.
● The on-screen display only appears while the
camcorder searches for each scene.
● There may be noise at in- or out-points on the edited
tape with certain VCRs.
USER MAINTENANCE
42
EN
After Use
LENS COVER
open/close switch
Set the power switch to POWER OFF to turn off the
camcorder.
1
2
3
4
5
6
Press EJECT to open the cassette holder, then remove
the cassette.
Close and lock the cassette holder by pressing
PUSH.
Close and lock the LCD monitor.
Press BATT. RELEASE to remove the battery pack.
Set to “POWER OFF”.
BATT. RELEASE
Slide the LENS COVER open/close switch to close
the lens cover.
PUSH
EJECT
Cleaning The Camcorder
CLEAN EXTERIOR
Wipe gently with a soft cloth.
1
CLEAN LCD MONITOR
Slide MONITOR OPEN to open the LCD monitor
and wipe gently with soft cloth. Be careful not to
damage the monitor. Close the LCD monitor.
Remove.
2
MONITOR OPEN
CLEAN LENS
Blow it with a blower brush, then wipe gently with
lens cleaning paper.
3
4
5
6
REMOVE EYEPIECE
Turn the eyepiece counterclockwise and pull it out.
CLEAN VIEWFINDER
Marks
Remove dust using a blower brush.
RE-ATTACH EYEPIECE
Align the marks, re-attach the eyepiece and turn it
clockwise.
NOTES:
● Avoid using strong cleaning agents such as benzine or
alcohol.
● Cleaning should be done only after the battery pack
has been removed or other power units have been
disconnected.
● Mold may form if the lens is left dirty.
TROUBLESHOOTING
EN
43
SYMPTOM
POSSIBLE CAUSE(S)
POWER
No power is supplied.
● The battery pack has not been attached correctly
(੬ pg. 8).
● The battery pack is not charged (੬ pg. 8).
● The power supply has not been correctly connected
(੬ pg. 9).
The power suddenly goes off and
doesn’t come back on by itself.
● The battery pack has completely discharged.
● Remove the cassette and disconnect the power source,
then after a few minutes, try turning the power back on. If
it still doesn’t come on, consult your nearest JVC dealer.
RECORDING
Recording cannot be performed.
● The recording tape’s Erase Protection tab is missing. Cover
the hole with adhesive tape. (Some tapes have sliding
tabs. In this case, check the position of the tab.)
Recording does not start.
● The camcorder Power switch has not been set to “CAM-
ERA” (੬ pg. 15).
PLAYBACK
The tape is running, but there’s no
playback picture.
● The TV has not been set to its VIDEO mode or channel.
● If A/V connection is used, the TV’s VIDEO/TV switch has
not been set to VIDEO.
● The RF unit has not been set to the correct channel.
Noise bars appear in the playback
picture.
● Manual Tracking has not been performed (੬ pg. 35).
Playback picture is blurred or
interrupted.
● The video heads are dirty or worn out. Consult your
nearest JVC dealer for head cleaning or replacement.
The counter indication is blurred
during Still playback.
● This is normal.
TAPE TRANSPORT
The tape stops during fast-forward
or rewind.
● The Counter Memory Function has been activated
(੬ pg. 35).
Rewinding or fast-forwarding cannot
be performed.
● The tape is already fully wound on one reel or the other.
TROUBLESHOOTING (cont.)
44
EN
SYMPTOM
POSSIBLE CAUSE(S)
OTHER
The tape won’t eject.
● The battery pack is running low.
● If the LCD monitor is not open over 45 degrees, EJECT
switch does not function.
Some functions are not available.
● The PROGRAM AE select dial is set to “AUTO LOCK”.
Vertical white lines appear when
shooting a very bright object.
● This sometimes occurs when the contrast between the
background and the object is great. It is not a defect of the
camcorder.
Bright, crystal-shaped spots appear
in the LCD monitor and the
viewfinder.
● Sunlight is directly entering the lens. This is not a defect of
the camcorder.
The rear of the LCD monitor is hot.
● The light used to illuminate the LCD monitor causes it to
be hot. Close the LCD monitor to turn it off or set the
power switch to OFF, and let the unit cool down.
Colored bright spots appear all over
the LCD monitor.
● The LCD monitor is made with high-precision technology.
However, black spots or bright spots of light (red, green or
blue) may appear constantly on the LCD monitor. These
spots are not recorded on the tape. This is not due to any
defect of the unit. (Effective dots: more than 99.99 %.)
The indicators and the picture color
on the LCD monitor are not clear.
● This may occur when the surface or the edge of the LCD
monitor is pressed.
The LCD monitor, the viewfinder
and the lens have become dirty (ex.
fingerprints).
● Wipe them gently with soft cloth. Gently wipe the LCD
monitor in a semicircle because wiping strongly spreads the
stain and it won’t come out easily.
The picture is blurred in the Quick
Review or Retake mode.
● This is normal while recording in the EP mode. Some noise
may be present while recording in the SP mode (੬pg. 12).
An error number (i.e. E03) appears
in the LCD monitor or the view-
finder.
● Turn the camcorder’s power off, then disconnect the
power source. After a few minutes, try turning the power
on again. If the error number still appears in the view-
finder, consult your nearest JVC dealer.
The image is out of focus.
● The diopter needs to be adjusted (੬ pg. 10).
● The scene being shot is adversely affecting the operation
of Auto Focus (੬ pg. 22).
A character generator title and the
date and time displays disappear
from the LCD monitor or the
viewfinder.
● If you remove the power source from the camcorder while
the power is on, all settings and selections are erased. Make
sure to turn the camcorder’s power off before disconnecting
the power source.
The wrong date and time are
displayed/recorded.
● If you have not performed Date/Time Setting (੬ pg. 11),
the date and time are not displayed/recorded correctly. Be
sure that Date/Time setting is carried out.
Even though the Lens Cover is open,
the Lens Cover Warning indicator
blinks.
● The Lens Cover Warning indicator may blink when the
camcorder is used in dark areas, regardless of the position
of the Lens Cover.
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio,
etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit
(battery pack, AC Power Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and
proceed as usual from the beginning.
INDEX LCD monitor/Viewfinder
EN
45
1 * 2 * 3
4
5 *
6
% *
^
&
*
(
)
q
18min
Disp.
T30
REC SP
7
Sepia
8
9
0
!
@
#
$
–05
MWB
PAUSE
1min
1/2s
TAPE END
Merry Christmas
DEC 25. 97
AM 10 : 24 : 56
LCD monitor/Viewfinder Indications
1 * Cassette Warning/Remaining
# Instant Title Display ............................ ੬ pg. 26
Tape Time ......................................... ੬ pg. 15
$ Date/Time Character Display .............. ੬ pg. 28
% * Battery Pack Remaining Power Indicator
Changes as follows according to the battery
pack’s remaining power level:
When no cassette is inserted: the Cassette (
Warning blinks.
When Erase Protection tab is not in the position
that allows recording: the Cassette ( ) Warning
lights. Otherwise, the Remaining Tape Time is
displayed. When the Power switch is set to
“PLAY” and a tape is loaded: the Cassette (
mark is displayed regardless of the Erase
Protection tab’s position.
)
“
”. When the power is
almost gone, the indicator blinks, then the unit
shuts off. Replace the battery pack with a fully
charged one.
)
(Note: The symbol containing 3 darkened
squares —
— does not necessarily mean
2 * Recording Mode (SP/EP) Indicator .... ੬ pg. 12
that the battery pack is fully charged.)
3, 8 PROGRAM AE Indicator................ ੬ pg. 20
Displayed at 3 for approx. 1 second when the
PROGRAM AE select dial is switched from one
position to another. Then only the indicator
remains at 8.
^ Focus Indicator ................................... ੬ pg. 22
& Exposure Level Indicator ..................... ੬ pg. 24
* White Balance Mode Indicator ........... ੬ pg. 29
( Menu Setting Change Indicator........... ੬ pg. 30
) Clock Warning
3, 9 Fade/Wipe Standby Indicator ........ ੬ pg. 25
Displayed at 3 for approx. 2 seconds when the
Fade/Wipe is switched from one function to
another by pressing the SET button. Then only
the indicator remains at 9.
Once the power is turned on and the indicator
blinks for about 10 seconds, perform the date
and time settings (੬ pg. 11). After setting is
complete, turn the power off and disconnect the
power source. If you re-connect it and turn the
power on and the indicator is blinking, that
means that the clock (lithium) battery is either
not installed or has discharged. Install, or replace
the old battery with, a new one (੬ pg. 10).
q •Tape End Display: TAPE END ........... ੬ pg. 15
Appears when the end of the tape is reached
during playback, recording or fast-forward.
•Condensation Warning:
4 Program Manager Function
Indication ........................................... ੬ pg. 25
Appears when the PROGRAM AE select dial is
set to any position other than AUTO LOCK.
5 * Tape Length Display ......................... ੬ pg. 12
6 Zoom Indicator bar ............................. ੬ pg. 18
7 Recording Indicator ............................ ੬ pg. 15
0 Picture Stabilizer Indicator .................. ੬ pg. 24
! Interval Time/Recording
When this indication appears, all functions are
disabled. Turn the unit off (without removing
the power source) for a few hours, and when
you turn it on again the indicator should
disappear.
Time Indicator..................................... ੬ pg. 32
@ •Record–Standby Mode Indicator ...... ੬ pg. 15
•Lens Cover Warning:
LENS COVER ................................... ੬ pg. 15
* : During recording, pressing DISPLAY lets you remove indications marked with * from the screen.
INDEX Controls
46
EN
3
5
7 9
2
4
6
0
!
r
8
1
u
T W R
%
s
@
#
$
*
(
)
O
e
q
w
d
t y
U
I
Y
i p o Q
a
P
E
^
&
EN
47
Controls
Connectors
1 MONITOR OPEN Switch.................... ੬ pg. 16
u J terminal (JLIP (Joint Level Interface Protocol)
Connector.)
2 REW Button ....................................... ੬ pg. 34
RETAKE R [Quick Review] Button ....... ੬ pg. 19
3 FF Button ........................................... ੬ pg. 34
RETAKE F Button ................................ ੬ pg. 19
(Located beneath the jack cover)
• Connect the Editing Cable when performing
Random Assemble Editing (੬ pg. 40).
•It is used to connect the camcorder to a device
such as a personal computer.
For further detail consult your nearest JVC
dealer.
4 PLAY/PAUSE Button ........................... ੬ pg. 34
5 STOP Button ...................................... ੬ pg. 34
6 SEL. Button ........................................ ੬ pg. 25
7 SET Button ......................................... ੬ pg. 25
8 Power Zoom Lever ............................ ੬ pg. 18
9 DISPLAY Button ................................. ੬ pg. 15
0 MENU Button .................................... ੬ pg. 30
i DC IN Jack ......................................... ੬ pg. 9
The jacks o to Q are located beneath the jack
cover.
o VIDEO OUT Jack ............................... ੬ pg. 36
p RF DC OUT Jack ................................ ੬ pg. 36
Q AUDIO OUT Jack .............................. ੬ pg. 36
! Multi-Function Control
•Exposure +/– ................................... ੬ pg. 24
•Focus FAR/NEAR ............................. ੬ pg. 22
•Menu Setting Change ....................... ੬ pg. 30
•Tracking +/– .................................... ੬ pg. 35
Indicators
W Tally Lamp ......................................... ੬ pg. 15
E Power On Indicator ........................... ੬ pg. 15
@ PUSH Button ..................................... ੬ pg. 13
# EJECT Switch...................................... ੬ pg. 13
$ BATT. [Battery] RELEASE Switch ......... ੬ pg. 8
% Diopter Adjustment............................ ੬ pg. 10
^ Recording Start/Stop Button ................ ੬ pg. 15
& POWER Switch .............................. ੬ pg.15, 34
Other Parts
R Camera sensor
Be careful not to cover this area; built-in
here is the sensor necessary for shooting.
T Microphone
Y Shoulder Strap Eyelets ........................ ੬ pg. 14
U Clock Battery Compartment ................ ੬ pg. 10
I Battery Pack Mount ........................... ੬ pg. 8
O Electronic Viewfinder......................... ੬ pg. 10
P LENS COVER Switch ......................... ੬ pg. 15
a Grip Strap .......................................... ੬ pg. 14
s Speaker .............................................. ੬ pg. 34
d Tripod Mounting Socket ......................੬ pg. 14
* Recording Mode [SP/EP] Select
Button ................................................ ੬ pg. 12
R.A.EDIT CANCEL Button ................... ੬ pg. 40
( R.A.EDIT IN/OUT Button.................... ੬ pg. 40
) Tape Length [T20•30•40]
Select Button...................................... ੬ pg. 12
COUNTER R [Reset]/M [Memory]
Button ................................................ ੬ pg. 35
q EDIT Button ....................................... ੬ pg. 41
w R.A.EDIT Button................................. ੬ pg. 40
e PICTURE STABILIZER Button .............. ੬ pg. 24
r PROGRAM AE Select Dial .................. ੬ pg. 20
t BRIGHT Dial ..................................... ੬ pg. 34
y VOLUME Dial ................................... ੬ pg. 34
INDEX Terms
48
EN
A
M
AC Power Adapter .................................. pg. 8
Animation Recording .............................. pg. 33
Auto Date Record ................................... pg. 28
Auto Focus ............................................. pg. 22
Auto Mode Lock Mode ........................... pg. 21
Auto Mode Release Mode .......................pg. 21
Manual Focus ......................................... pg. 23
MBR Code Setting................................... pg. 39
N
ND Effect Mode ...................................... pg. 21
P
B
Picture Stabilizer..................................... pg. 24
Playback ................................................. pg. 34
Program AE with Special Effects ...............pg. 20
Provided Accessories .............................. pg. 6
Battery Pack ............................................ pg. 8, 49
Brighten the Image.................................. pg. 24
C
Q
Car Battery.............................................. pg. 9
Cassette Adapter ..................................... pg. 37
Character Generator ............................... pg. 27
Charge Marker ........................................ pg. 9
Charging the Battery Pack ........................pg. 8
Clock (Lithium) Battery ........................... pg. 10
Connection to a VCR/TV ........................ pg. 36
Contents ................................................. pg. 7
Counter Memory .................................... pg. 35
Quick Review ......................................... pg. 18
R
Random Assemble Editing ....................... pg. 39–41
Recording, Advanced Features ................ pg. 20–33
Recording ............................................... pg. 15
Recording, Start/Stop .............................. pg. 15
Recording Mode Setting ......................... pg. 12
Recording-Standby ................................. pg. 15
Remote Control Unit............................... pg. 39
Remove Cassette..................................... pg. 13
Retake..................................................... pg. 18
Rewind Tape ........................................... pg. 34
D
Darken the Image ................................... pg. 24
Date/Time/Character Insert ......................pg. 28
Date/Time Setting ................................... pg. 11
Discharge the Battery pack ......................pg. 8
Diopter Adjust ........................................ pg. 10
S
Self-Timer ............................................... pg. 32
Sepia Mode ............................................ pg. 21
Shoulder Strap Attachment ......................pg. 14
Shuttle Search ......................................... pg. 35
Specifications ......................................... pg. 55
Sports Mode ........................................... pg. 21
Still Playback .......................................... pg. 35
E
Electronic Fog Filter Mode .......................pg. 21
Erase Protection ...................................... pg. 13
Exposure Control .................................... pg. 24
F
Fade-in/out ............................................. pg. 25
Fast-Forward Tape................................... pg. 34
Focus Lock ............................................. pg. 22
T
Tape Counter .......................................... pg. 34
Tape Dubbing ......................................... pg. 38
Tape Length Setting ................................. pg. 12
Time-Lapse Shooting............................... pg. 33
Tracking .................................................. pg. 35
Tripod Mounting ..................................... pg. 14
Twilight Mode......................................... pg. 21
G
Grip Adjustment ..................................... pg. 14
H
High Speed Shutter Mode ........................pg. 21
I
V
Insert Cassette ......................................... pg. 13
Instant Titles............................................ pg. 26
Viewfinder Adjustment ........................... pg. 10
W
L
White Balance Adjustment ......................pg. 29
Wide Mode............................................. pg. 26
LCD monitor/Viewfinder, indications....... pg. 45
J
Z
Journalistic shooting ............................... pg. 17
Zooming ................................................. pg. 18
CAUTIONS
When using the AC Power Adapter/Charger in
areas other than the USA
Ⅲ The provided AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
EN
49
General Battery Precautions
•When the C-P6U or C-P7U (cassette adapter) is not
functioning even when correctly operated, the battery
is exhausted. Replace it with fresh one.
•Use only the following batteries:
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to an
AC wall outlet other than American National
Standard C73 series type use an AC plug adapter,
called a “Siemens Plug”, as shown.
For this AC plug adapter, consult your nearest JVC
dealer.
C-P6U or C-P7U ........................ AA (R6) size
Please make note of the following rules for battery use.
When misused, battery can leak or explode.
1. Refer to the C-P6U/C-P7U instructions when
replacing the battery.
2. Do not expose the battery to excessive heat as it can
leak or explode.
3. Do not dispose of battery in a fire.
4. Remove battery from the unit if it is to be stored for
an extended period to avoid battery leakage which
can cause malfunctions.
Plug adapter
Battery Packs
The supplied battery pack is a
nickel-cadmium battery. Before using
the supplied battery pack or an optional
battery pack, be sure to read the
following cautions:
INFORMATION
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two condi-
tions:
1. To avoid hazard . . .
..... do not burn.
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation. Change or modifications not
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment. This equipment has been tested and
found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the instruc-
tions, may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
..... do not short-circuit the terminals. Terminals
..... do not modify or disassemble.
..... use only specified chargers.
2. To prevent damage and prolong service life . . .
..... do not subject to unnecessary shock.
..... avoid repeated charging without fully discharg-
ing.
..... charge in an environment where
temperatures are within the tolerances shown in
the chart below. This is a chemical reaction type
battery—cooler temperatures impede chemical
reaction, while warmer temperatures can
prevent complete charging.
..... store in a cool, dry place. Extended exposure to
high temperatures will increase natural
discharge and shorten service life.
..... avoid prolonged uncharged storage.
..... remove from charger or powered unit when not
in use, as some machines use current even
when switched off.
3. To prevent damage to the camcorder . . .
..... replace the battery pack when it begins to
deliver less recording time per charge.
NOTE:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
It is normal for the battery pack to be warm after
charging, or after use.
Temperature Range Specifications
Charging ...................................... 10°C to 35°C
Operation .................................... 0°C to 40°C
Storage......................................... –10°C to 30°C
Consult the dealer or an experienced radio/TV
technician for help.
NOTES:
● Recharging time is based on room temperature of
20°C.
● The lower the temperature, the longer recharging
takes.
CAUTIONS (cont.)
50
EN
4. To protect the unit, DO NOT . . .
Cassettes
..... allow it to become wet.
..... drop the unit or strike it against hard objects.
..... subject it to shock or excessive vibration during
transportation.
To properly use and store your cassettes, be sure to read
the following cautions:
1. During use . . .
..... keep the lens directed at extremely bright
objects for long periods.
..... make sure the cassette bears the VHS-C mark.
..... be aware that recording onto prerecorded tapes
automatically erases the previously recorded
video and audio signals.
..... direct the eyepiece of the viewfinder at the sun.
..... carry it by holding the viewfinder or the LCD
monitor. Be sure to hold the main unit with both
hands or use the grip.
..... make sure the cassette is positioned properly
when inserting.
..... swing it excessively when using the shoulder
strap.
..... do not load and unload the cassette
repeatedly without allowing the tape to run at
all. This slackens the tape and can result in
damage.
5. This camcorder features a built-in head cleaner
which automatically cleans the heads and head
drum when a cassette is loaded or unloaded. If,
however, the heads become dirty and cause
blurriness or interruption in the playback
picture, consult your nearest JVC dealer.
..... do not open the front tape cover. This exposes
the tape to fingerprints and dust.
2. Store cassettes . . .
..... away from heaters or other heat sources.
..... out of direct sunlight.
..... where they won’t be subject to unnecessary
shock or vibration.
LCD monitor
..... where they won’t be exposed to strong magnetic
fields (such as those generated by motors,
transformers or magnets).
1. To prevent damage to the LCD monitor, DO
NOT . . .
..... push it strongly or apply any shocks.
..... place the camcorder with the LCD monitor on
the bottom.
..... vertically, in their original cases.
Main Unit
2. To prolong service life . . .
..... avoid rubbing it with coarse cloth.
1. For safety, DO NOT . . .
3. Make be aware of the following phenomena for
LCD monitor use. These are not mulfunctions. . . .
•While using the camcorder, the surface around the
LCD monitor and/or the back of the LCD monitor
may heat up.
•If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
..... open the camcorder’s chassis.
..... disassemble or modify the unit.
..... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use.
..... allow inflammables, water or metallic objects to
enter the unit.
..... remove the battery pack or disconnect the
power supply while the power is on.
..... leave the battery pack attached when the
camcorder is not in use.
About moisture condensation . . .
2. Avoid using the unit . . .
● You have observed that pouring a cold liquid
into a glass will cause drops of water to form on
the glass‘ outer surface. This same phenomenon
occurs on the head drum of a camcorder when it
is moved from a cool place to a warm place,
after heating a cold room, under extremely
humid conditions or in a place directly subjected
to the cool air from an air conditioner.
..... in places subject to excessive humidity or dust.
..... in places subject to soot or steam such as near a
cooking stove.
..... in places subject to excessive shock or vibration.
..... near a television set.
..... near appliances generating strong magnetic or
electric fields (speakers, broadcasting antennas,
etc.).
..... in places subject to extremely high (over 40°C
or 104°F) or extremely low (under 0°C or 32°F)
temperatures.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
3. DO NOT leave the unit . . .
..... in places of over 50°C (122°F).
..... in places where humidity is extremely low
(below 35%) or extremely high (above 80%).
..... in direct sunlight.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
..... in a closed car in summer.
..... near a heater.
SPECIFICATIONS
GENERAL
EN
51
AUDIO
Output
Format
: VHS NTSC standard
: –8 dBs, 1 k-ohm
(via AUDIO out
connector)
: 20 mm round x 1,
monaural
Power source
Power consumption
LCD monitor off,
viewfinder on
LCD monitor on,
viewfinder off
Signal system
Video recording system
Luminance
: DC 6V
Speaker
: 6.5 W
: 6.9 W
: NTSC-type
AC POWER ADAPTER/BATTERY CHARGER
(AA-V11U)
Power requirement
: FM recording
: Converted sub-carrier
direct recording
Conforms to VHS
standard
U.S.A. and Canada : AC 120 V`, 60 HZ
Color
Other countries
: AC 110 V to 240 V`,
50/60 Hz
Power consumption
Output
Charge
VTR
Charging system
: 23 W
Cassette
Tape speed
SP
:
cassette
: DC 8.5 V
: DC 6.3 V
, 1.3 A
, 1.8 A
: Constant current, peak
detection, timer
: 33.35 mm/sec.
(1-5/16 ips)
: 11.12 mm/sec. (7/16 ips)
EP
controlled
Recording time (max.)
Dimensions
Weight
: 150 (W) x 42 (H) x
68 (D) mm (5-15/16” x
1-11/16” x 2-11/16”)
: Approx. 320 g (0.71 lbs)
SP
EP
: 40 minutes
: 120 minutes
(with TC-40 cassette)
Operating temperature : 0°C to +40°C
(32°F to 104°F)
CASSETTE ADAPTER (C-P7U)
Dimensions
Operating humidity
Storage temperature
: 35% to 80%
: 188 (W) x 25 (H) x
104 (D) mm (7-7/16” x 1”
x 4-1/8”)
: Approx. 240 g (0.53 lbs)
: “AA (R6)”-size battery x 1
: –20°C to +50°C
(–4°F to 122°F)
Weight
Dimensions
(Including viewfinder)
: Approx. 1030 g (2.3 lbs)
: 118 (W) x 115 (H) x
231 (D) mm (4-11/16” x
4-9/16” x 9-1/8”)
Weight
Accessory
Provided Accessories ......................੬ pg. 6
CAMERA
Pick up
Lens
Optional Accessories
: 1/4” format CCD
: F1.6, f = 3.8 to 68.4 mm,
18:1 power zoom lens
with auto iris and macro
control, filter diameter
46 mm
: Electronic viewfinder
with 0.5” black/white
CRT
•Battery Packs BN-V12U, BN-V22U, BN-V25U
•Car Battery Charger BH-V3U
•Battery Charger BH-VC10U
•Car Battery Cord AP-V7U
•RF Unit RF-V5U
•Compact VHS-C Cassettes TC-40/30/20
•Active Carrying Bag CB-V7U
•Wireless Remote Control Unit RM-V700U
The RM-V700U cannot be used to operate this
camcorder.
This camcorder can use the RM-V700U only for
R.A. Edit with a non-JVC VCR.
Viewfinder
White balance
adjustment
: Auto/Manual adjustment
LCD MONITOR
Size
LCD system
: 3" diagonally measured
: LCD/TFT active matrix
system
Some acccessories are not available in some areas.
Please consult your nearest JVC dealer for details on
accessories and their availability.
VIDEO
Output
Specifications shown are for SP mode unless
otherwise indicated. E. & O. E. Design and
specifications subject to change without notice.
: 1 Vp-p, 75 ohms,
unbalanced (via VIDEO
out connector)
ESPAÑOL
52
EN
Alimentación
Indicador CHG. (carga)
Marcas
Esta videocámara posee un sistema de alimentación de 3
vías que le permite seleccionar la fuente de alimentación
más apropiada.
A la toma de
corriente de
CA
Indicador POWER
NOTAS:
● Sin alimentación no hay ninguna función disponible.
● Utilice exclusivamente la alimentación indicada.
● No utilice la unidades de alimentación suministradas
con otro equipo.
Indicador END
CARGA DE LA BATERIA
ALIMENTACION
Interruptor REFRESH
Indicador REFRESH
Enganche.
Conecte el cable de alimentación de CA del
cargador a una toma de corriente. Se encenderá la
luz del indicador de alimentación.
1
COLOCACION DE LA BATERIA
Alinee las marcas y deslice la batería en la
dirección de la flecha hasta que quede bloqueada
2
en su lugar.
Se enciende la luz indicadora CHG.
Empuje.
EXTRACCION DE LA BATERIA
BATT. RELEASE
Cuando la carga está completa, se encenderá el
indicador END. Deslice la batería en el sentido
opuesto al de la flecha.
3
Marcador de carga
BATERIA
CARGA
DESCARGA
BN-V11U
BN-V12U
BN-V22U
BN-V25U
aprox. 1 h 10 m
aprox. 1 h 10 m
aprox. 2 h 10 m
aprox. 2 h 40 m
aprox. 3 h 30 m
aprox. 3 h 30 m
aprox. 7 h
aprox. 10 h
**INDICADOR DE CARGA
Se ha suministrado un indicador de carga
sobre la batería para ayudarle a recordar si ha
sido cargado o no. Los dos colores
suministrados (rojo y negro), le permiten
seleccionar la carga y la descarga.
USO DE LA BATERIA
COLOCACION DE LA BATERIA
Enganche la parte superior del mismo en la
videocámara y empújela hasta que se bloquee en su
lugar.
**REFRESCADO
El adaptador de CA se caracteriza por la
función REFRESH que le permite descargar
totalmente la batería antes de recargarla.
1
2
EXTRACCION DE LA BATERIA
Para descargar las baterías . . .
..... coloque la batería en el adaptador como se
muestra en la ilustración arriba. Luego
presione REFRESH. El indicador REFRESH
se enciende cuando se inicia la descarga y
se apaga cuando la descarga ha terminado.
Deslice BATT. RELEASE y extraiga la batería.
Tiempo de grabación aproximado (unidad: m.)
BATERIA
Monitor LCD
activado/Visor
desactivado
Monitor LCD
desactivado/Visor
activado
ATENCION:
Antes de desmontar la fuente de alimenta-
ción, asegúrese que la alimentación de la
cámara de video esté desconectada. El no
hacerlo puede producir una falla de
funcionamiento en la videocámara.
BN-V11U
BN-V12U
BN-V22U
BN-V25U
50
50
105
145
55
55
115
155
GUIA PARA OPERACION RAPIDA
Si la unidad comienza a funcionar mal, deje de usarla inmediatamente y consulte a su concesionario local de JVC.
EN
53
ALIMENTACION
INSERCION DEL CASSETTE
DE VIDEO
Enganche.
EJECT
1
2
Empuje.
3
4
2
BATT. RELEASE
PUSH
Utilización de la batería
1
1 Enganche el extremo superior de la batería
en la videocámara. (Procedimiento para
carga: ੬ P. 8)
MONITOR OPEN
1 Deslice MONITOR OPEN para abrir el
monitor LCD.
2 Empuje la batería hacia adentro hasta que
quede bloqueada en su lugar.
Para extraer la batería
Deslice BATT. RELEASE y extraiga la batería.
•Abra a un ángulo mayor de 45 grados.
2 Presione EJECT para abrir el portacassette.
3 Inserte cassette de video.
4 Presione PUSH para cerrar el portacassette.
(Por más detalles, ੬ P. 13.)
REPRODUCCION
PLAY/PAUSE (reproducción/pausa)
3
FILMACION
STOP
(parada)
1
Perilla de
abertura/cierre
LENS COVER
2
REW (rebobinado)
2
1
Colóquelo en “CAMERA”.
Colóquelo en “PLAY”.
3
Botón para inicio/parada de grabación
1 Ajuste el interruptor de alimentación en “PLAY”.
2 Presione REW.
1 Deslice la perilla de abertura/cierre LENS
COVER para abrir la tapa del objetivo.
2 Adjuste el interruptor de alimentación en
“CAMERA”.
— El indicador de alimentación se
encenderá y aparecerá una imagen en el
monitor LCD o en el visor.
— La cinta se detiene automáticamente al
comienzo de la misma.
3 Presione PLAY/PAUSE.
— Comienza la reproducción y la imagen
aparece en el visor o en el monitor LCD.
•Presione STOP para detener la grabación.
(Por más detalles, ੬ P. 34.)
3 Presione el botón inicio/parada de
grabación.
•El visor se desconecta automáticamente para
ahorrar energía cuando el monitor LCD es
abierto a un ángulo mayor de 45 grados.
•El monitor LCD se activa/desactiva cuando se
lo abre/cierre a 45 grados aprox.
— Comenzará la grabación.
• Para detener temporariamente la grabación,
presione nuevamente el botón de inicio/parada
de grabación. (Por más detalles, ੬ P. 15, 16.)
• El visor se desconecta automáticamente para
ahorrar energía cuando el monitor LCD es
abierto a un ángulo mayor de 45 grados.
• El monitor LCD se activa/desactiva cuando se
lo abre/cierre a 45 grados aprox.
O simplemente reproduzca la cinta en un
VCR de VHS utilizando el adaptador de
cassette (VHS Playpak). ੬ P. 37
FOR SERVICING
54
EN
HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE: 1-800-252-5722
Dear customer:
In order to receive the most satisfaction from your purchase, read the instruction booklet before
operating the unit. In the event that repair is necessary, or for the address nearest your location,
please refer to the factory service center list below or within the Continental United States, call 1-800-
252-5722 for your authorized servicer. Remember to retain your Bill of Sale for Warranty Service.
— JVC
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF US JVC CORP.
FACTORY SERVICE CENTER LOCATIONS
107 Little Falls Road
Fairfield, NJ 07004-2105
(201) 808-9279
1500 Lakes Parkway
Lawrenceville, GA 30243-5857
(770) 339-2522
705 Enterprise Street
Aurora, IL 60504-8135
(630) 851-7855
5665 Corporate Avenue
Cypress, CA 90630-4727
(714) 229-8011
10700 Hammerly Blvd., Suite 110 2969 Mapunapuna Place, Suite 101
Houston, TX 77043-2310
(713) 935-9331
Honolulu, HI 96819-2000
(808) 833-5828
230 Eliot Street
Ashland, MA 01721-2377
(508) 881-5923
8192 West State Road 84
Davie, FL 33324-4611
(954) 472-1960
890 Dubuque Avenue
South San Francisco, CA 94080-1804
(415) 871-2666
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the
engineering and production of the wide array of JVC products, service is the key to maintaining the
high level performance for which JVC is world famous. The JVC service and engineering organization
stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF US JVC CORP.
107 Little Falls Road
Fairfield, NJ 07004-2105
If you ship the product...
Pack your JVC unit in the original carton or one of equivalent size and strength. Enclose, with the unit,
a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you
received when you purchased your JVC unit. Print your home return address on the outside and the
inside of the carton. Send to the appropriate JVC Factory Service Center as listed above.
Don't service it yourself.
ACCESSORIES
To purchase accessories for your JVC product, you
may contact your local JVC Dealer.
Or from the 48 Continental United States call toll free:
1-800-882-2345.
CAUTION
To prevent electrical shock, do not open the
cabinet. No user serviceable parts inside.
Refer servicing to qualified service personnel.
WARRANTY
EN
55
LIMITED WARRANTY
CONSUMER VIDEO 1-90
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO
THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP
from the date of original retail purchase for the period as shown below. ("The Warranty Period")
PARTS
LABOR
1
YR
90
DAYS
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF
COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner.
Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized
service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All
products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for
Television sets having a screen size 25 inches and above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC
authorized service center, please call toll free: (800) 252-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with
a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center,
the name and location of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse,
faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility
authorized by JVC to render such service, or if affixed to any attachment not provided with the products, or if
the model or serial number has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of
purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);from the date
of purchase);
There are no other express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY
OTHER DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT
LIMITATION, DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT,
OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE
LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an
implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF US JVC CORP.
41 Slater Drive
Elmwood Park, New Jersey 07407
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR
DETAILS OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT
WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain
this information for future reference.
Model No.:
Serial No:
Purchase date:
Name of dealer:
JVC COMPANY OF AMERICA
DIVISION OF US JVC CORP.
41 Slater Drive, Elmwood Park, N.J. 07407
0P5ri9n7teTdOiVn*JaUpNa*n YP
U
COPYRIGHT© 1997 VICTOR COMPANY OF JAPAN, LTD.
|