Accessories
A Hexagonal head tapping screw
B Hexagonal head tapping screw
C Protection bar x 4
CAR STEREO SPEAKER
x 16 (R4 x 30 mm)
x 8 (R4 x 20 mm)
CS-WDS1
Use a M4 hex wrench.
D Paper pattern
For Tweeter
For Woofer
How to use the paper pattern
1. Cut out the paper pattern along the perforation.
2. Place and trace the paper pattern over the mounting
area on the vehicle or board.
3. Cut out the mounting area on the vehicle or board along
the marking.
Specifications
The diaphragm of this speaker makes use of birch wood to faithfully reproduce the original sound.
Each unit, therefore, has a unique appearance.
Type
: 2-Way Separate Speaker
Thiele/ Small Parameter
(14.5 cm Woofer)
Thank you for purchasing the JVC Car Stereo Speakers. For the secure installation and perfect operation of your
speaker, please read the following instructions carefully.
Frequency Response : 45 Hz - 50 kHz
Sound Pressure Level : 84 dB/W0m
Recommended Crossover Frequency
Revc (DC VC Res ) 3.4
Ohms
Ohms
Hz
: 4.5 kHz (Cut-off Slope:-12 dB/oct.)
Imp. (300Hz)
4
Mounting the speaker
14.5cm Wood Cone Woofer
Power Handling Capacity (Nominal)
: 50 W
Power Handling Capacity (Max. Music Power)
: 150 W
Impedance
Frequency Response : 45 Hz - 8 kHz
Sound Pressure Level : 84 dB/W0m
Fo (Res Freq )
Zo (Zmax at Fo)
Sd (Piston Area)
BL (Flux*Length)
Qms (Mech Q)
Qes (Elec Q)
80.2
Professional knowledge is required for mounting this speaker. For details, please consult the authorized dealer.
Make use of the paper pattern provided when processing the mounting board of the speaker.
During mounting, ensure that there is enough spacing to avoid hitting against any parts such as window glass.
In order to optimize the sound field of the wood cone, it is recommended that the speaker terminal be mounted at the
bottom with the wood grain in the vertical direction.
26.9
Ohm
sqM
TM
0.0095
6.08
: 4 K
3.814
0.667
0.568
4.13
Notes for dealers
Mass
: 1.5 kg (one piece)
Upon completing the mounting, please hand this instruction manual to the customer.
Qts (Total Q)
2cm Wood Dome Tweeter
Power Handling Capacity (Nominal)
Vas (Acous Vol)
Le (Inductance)
Cms (Compliance)
Mms (Total Mass)
Litr
For Proper Installation and Use
0.286
321.9
12.23
mH
: 50 W (4.5 KHz -12 db/oct. H.P.F.)
Power Handling Capacity (Max. Music Power)
: 150 W (4.5 KHz -12 db/oct. H.P.F.)
: 4 K
uM/N
Gram
Gram
1. Be sure to install the speakers according to the directions so as to prevent them from slipping accidentally out of position due to the
repeated impact of opening and closing doors or the tossing and bumping of the vehicle.
2. Set the wiring firmly on the floor of the vehicle, taking the utmost care not to break wires while installing. When installing the speakers
in the doors, extra attention must be paid to allowing reasonable play to the wires. The wiring, if given too much clip or clamp, will get
pinched in between the door and body of the vehicle when opening and closing doors.
3. Since the speaker installed in the door is positioned at the foot level, be careful not to damage the speaker by giving it an inadvertent
kick. Check the water outlet at the bottom of the door occasionally to ensure that it drains well, leaving no rainwater inside the door.
4. Before connecting the speakers to the amplifier, confirm that the power has been turned off. The click noise generated by the
connection if the power is on may damage the speakers.
Impedance
Mmd (DiaphmMass) 11.70
Frequency Response : 3 kHz - 50 kHz
Sound Pressure Level : 84 dB/W0m
Mass
: 235 g (one piece)
Designs and specifications are subject to change without notice.
5. The amplifier and speakers should be connected between corresponding terminals, i.e. “left” to “left”, and “right” to “right”, as well as
“+” to “+”, and “–” to “–”. Connection with reversed polarity will degrade the quality of stereo reproduction.
6. Do not subject the speakers to excessive input. Any excessive input may damage the speakers.
7. Make sure that the output impedance of the amplifier’s speaker terminal is rated at 4 ohms.
8. Please use a high-pass filter.
(Cut-off Frequency is 4.5 kHz and above -12dB/oct)
9. When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not apply thinner or solvent.
INSTRUCTIONS
LVT1405-002A
[E]
EN
2006 Victor Company of Japan, Limited
0606SKMSANTCN
|