Grizzly T10050 User Manual

MODEL T10050  
RIGHT ANGLE  
IRON BENDER  
INSTRUCTIONS  
Damage to your eyes, face, and hands could  
result from using this item without proper  
protective gear, such as safety glasses or a  
face shield, and gloves.  
Figure 1. Model T10050.  
Inventory (Figure 2)  
A. Bender (not shown).................................... 1  
B. Bender Handle ........................................... 1  
C. Work Stop Rod........................................... 1  
D. Hex Bolts M10-1.5 x 40 (Handle)............... 2  
E. Flat Washers 10mm (Handle) .................... 2  
F. Work Stop................................................... 1  
G. Work Stop Knob......................................... 1  
H. Hex Nut M12-1.75 (Work Stop Rod).......... 1  
B
C
H
F
G
d
Specifications  
e
Maximum Workpiece Thickness........ 3 Ga.(1564")  
Maximum Workpiece Width..............................4"  
Machine Weight.........................................81 lbs.  
Figure 2. inventory.  
If you need help with your new machine, call our  
Tech Support at: (570) 546-9663.  
Copy RiGHT © July, 2008 By G Rizzly iNdu STRial, iNC.  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
#JB10791 pRiNTed i N CHiNa  
3. Thread the work stop knob into the work stop,  
then slide the work stop onto the work stop  
rod (Figure 7).  
Assembly  
The Model T10050 requires only minimal assem-  
bly before use.  
Work Stop  
To assemble the machine:  
1. Connect the bender handle to the machine  
with the M10-1.5 x 40 hex bolts and 10mm  
flat washers (Figure 5).  
Hex Bolt  
x2  
Work Stop Rod  
Knob  
Figure 7. Work stop.  
Flat Washer  
Handle  
Figure 5. Attaching handle.  
2. insert the stop rod with the M12-1.75 hex nut  
into the base. Tighten the hex nut against the  
base to secure it (Figure 6).  
Hex Nut  
Work Stop Rod  
Figure 6. Attaching work stop rod.  
-3-  
T10050 Right angle iron Bender  
Mounting  
Operations  
once you have confirmed that your machine is  
assembled and functioning properly, mount it to a  
workbench through the holes in the base. Be sure  
the workbench will remain stable when bending  
force is applied to the machine. if necessary,  
anchor the workbench to a wall or the floor to  
provide the necessary stability.  
Creating Bends  
1. lift the clamp cam shaft to release the clamp  
die. Rotate the clamp die as necessary to  
accommodate the thickness of your work-  
piece, then slide the clamp cam shaft back  
into the base (Figures 10 & 11).  
The strongest mounting option is a "Through  
Mount" where holes are drilled all the way through  
the workbench, and hex bolts, washers, and  
hex nuts are used to secure the machine to the  
workbench.  
Cam Shaft  
7dai  
die  
;aViꢀLVh]Zg  
-ACHINE "ASE  
Figure 10. Lifting clamp cam shaft and die.  
7ORKBENCH  
;aViꢀLVh]Zg  
AdX`ꢀLVh]Zg  
=ZmꢀCji  
Figure 8. example of a through mount setup.  
another option for mounting is a "direct Mount"  
where the machine is simply secured to the work-  
bench with a lag screw.  
AV\ꢀHXgZl  
Figure 11. Clamp die positions.  
;aViꢀLVh]Zg  
-ACHINE "ASE  
7ORKBENCH  
Figure 9. example of a direct mount setup.  
-4-  
T10050 Right angle iron Bender  
2. place the workpiece into the clamp and adjust  
the workpiece position as needed. Rotate the  
clamp cam shaft to clamp the workpiece  
(Figure 12).  
4. use the handle to bend the workpiece to the  
desired angle (Figure 14).  
Figure 14. Bending workpiece.  
Figure 12. Clamping workpiece.  
5. loosen the bending plate and clamp cam  
shaft to release the workpiece (Figure 15).  
if the clamp die does not move far enough  
to fully clamp the workpiece, repeat Steps  
1 & 2.  
88L  
3. adjust the bending plate to support the work-  
piece while bending (Figure 13).  
8L  
Figure 15. Releasing workpiece.  
Figure 13. Tightening bending plate.  
NOTICE  
Use the machine only as it is intended to be  
used. Adding cheater bars or other meth-  
ods of increasing leverage may damage the  
machine and will void the warranty.  
-5-  
T10050 Right angle iron Bender  
2. Bend the workpiece to the desired angle,  
then slide the angle stop against the bender  
base. Turn the angle stop to lock it in position  
(Figure 17).  
Repetitive Bends  
To ensure consistent and accurate bends when  
performing multiple, identical operations, use the  
work stop and angle stop.  
To use the work stop and angle stop:  
7ZcYZgꢀ7VhZ  
1. place the workpiece in the machine as need-  
ed, then slide the work stop against the end  
of the workpiece. Tighten the work stop knob  
(Figure 16).  
6c\aZꢀHide  
8L  
Figure 17. Using angle stop.  
Ldg`ꢀHide  
3. With each new workpiece, place the work-  
piece against the work stop, clamp it, then  
bend it until the moving bender base contacts  
the angle stop.  
Ldg`e^ZXZ  
Figure 16. Using work stop.  
-6-  
T10050 Right angle iron Bender  
parts Breakdown & List  
.
'&  
-
'%  
+
&'  
'*  
*
'%  
'(  
')"&  
&(  
&.  
&."&  
&,  
,
&*  
)
')  
'
''  
&+  
&
(
&)  
&)"&  
&-  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
1
PT10050001  
PT10050002  
PT10050003  
PT10050004  
PT10050005  
PT10050006  
PT10050007  
PT10050008  
PT10050009  
PT10050012  
PT10050013  
PT10050014  
BODY  
15  
16  
17  
18  
19  
PT10050015  
WORK STOP  
2
CRANK  
PT10050016  
PSW03-1  
WORK STOP ROD  
KNOB M10-1.5 x 35  
PLASTIC GRIP  
3
HANDLE  
4
STATIONARY JAW  
BENDING PLATE  
BENDING PLATE KNOB  
PT10050018  
PB31M  
5
HEX BOLT M10-1.5 X 40  
FLAT WASHER 10MM  
6
19-1 PW04M  
7
BENDING PLATE LEADSCREW  
CLAMP DIE  
20  
21  
22  
23  
24  
PSB14M  
PRP08M  
PN09M  
CAP SCREW M8-1.25 X 20  
ROLL PIN 6 X 30  
8
9
CLAMP CAM SHAFT  
COVER PLATE  
HEX NUT M12-1.75  
CAP SCREW M10-1.5 X 25  
HEX BOLT M10-1.5 X 35  
HEX NUT M10-1.5  
12  
13  
14  
PSB64M  
PB14M  
END PLATE  
ANGLE STOP  
24-1 PN02M  
25 PT10050025  
14-1 PSN05M  
SQUARE NUT M12-1.75  
PIVOT PIN  
-7-  
T10050 Right angle iron Bender  
"UY $IRECT AND 3AVE WITH 'RIZZLY® n 4RUSTEDꢀ 0ROVEN AND A 'REAT 6ALUEꢁ  
6ISIT /UR 7EBSITE 4ODAY !ND $ISCOVER  
7HY 'RIZZLY® )S 4HE )NDUSTRY ,EADERꢀ  
s 3%#52% /2$%2).'  
s /2$%23 3()00%$ 7)4(). ꢃꢄ (/523  
s %ꢂ-!), 2%30/.3% 7)4(). /.% (/52  
ꢂ/2ꢂ  
#ALL 4ODAY &OR !  
&2%%  
&ULL #OLOR #ATALOG  

Black Decker SB3000 User Manual
Burnham ES2 User Manual
Burnham MEGASTEAM MST629 User Manual
Canon Camcorder SD550 User Manual
Crown Boiler XE 3 User Manual
Desa 598 1034 02 User Manual
Eclipse Fujitsu Ten AVX5000 User Manual
Epson Camera Accessories 750Z User Manual
IBM M400 User Manual
JL Audio Stealthbox 011180 User Manual