JL Audio Stealthbox 011180 User Manual

®
Stealthbox  
I N S TALLATI O N GUI DE  
START  
HERE  
for the  
SB-T-TUNCNSL2/10W3v2  
(03-Up Toyota Tundra Access & Double Cab  
with front bucket seats and center console)  
STEP 1: Using a 14mm socket, remove the  
four bolts that secure the passenger side front  
seat.  
STEP 2: Tilt the seat to the rear, unplug the  
exposed wire assembly, remove the seat from  
the truck.  
STEP 3: Remove the front storage access  
door. Using a 10mm socket, remove the  
exposed bolts.  
This Stealthbox is a product which  
requires professional installation skills and  
tools.  
Please read this installation guide thor-  
oughly before beginning the project. It  
will guide you step by step through the  
installation. Several of the steps in this  
process may require two people to  
accomplish.  
It is absolutely vital that the enclosure  
be properly mounted to the vehicle  
according to these instructions. Failure  
to mount the enclosure properly pres-  
ents two problems: 1) The sub-bass  
performance will suffer due to the  
movement of the enclosure caused by  
the force exerted by the woofer(s) and  
2) A loose enclosure presents a serious  
safety hazard in the event of a collision  
or sudden deceleration.  
STEP 4: With the main storage door open,  
grab ahold of the black cup holder section  
and pull up.  
STEP 5: Using a 10mm socket, remove the  
exposed bolts. Also remove the bolts that are  
located at the bottom of the main storage  
bucket.  
STEP 6: Remove the plastic buttons that are  
located on each side of the center console.  
Please enjoy your JL Audio Stealthbox  
responsibly.  
Continued on Next Page  
SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005  
Page 1  
Sheet SKU#011180 Revision 4/6/2005  
Cont.  
From  
Previous  
Page  
STEP 15: Place the Stealthbox into position, Press  
down firmly.  
STEP 14: Thread in the three supplied socket cup  
set screws into the Stealthbox. Make sure that the  
socket ends are on the outside of the Stealthbox.  
The rear(left side of pic) threaded rods need to  
protrude about 1 1/4” out of the Stealthbox.The  
front socket cup set screw needs to protrude about  
3/4”.  
Place the Stealthbox into location. Slide the rear  
socket cup set screw through the drilled out holes  
from STEP10. Press firmly on the front of the  
Stealthbox, marking the wax square.  
STEP 16(b): *Tundra Double Cab O nly*  
STEP 16(a): *Tundra Access Cab O nly*  
Remove the Stealthbox.You should have an impres-  
sion on the wax square.  
Remove the Stealthbox.You should have an impres-  
sion on the wax square.  
*CAUTIO N*  
*CAUTIO N*  
Before drilling, make sure that you are not going to  
be drilling into any gas lines, brake lines, transmission  
lines, electrical wiring, transfer case(4x4 vehicles) or  
anything else that might cause a reduction in your  
weekly pay. Always wear eye protection when drilling.  
Before drilling, make sure that you are not going to  
be drilling into any gas lines, brake lines, transmission  
lines, electrical wiring, transfer case(4x4 vehicles) or  
anything else that might cause a reduction in your  
weekly pay. Always wear eye protection when drilling.  
With the use of a 1/2” drill bit and drill. Drill out the  
floor at the impression on the wax square  
With the use of a 1/2” drill bit and drill. Drill out the  
floor at the impression on the wax square  
Continued on Next Page ➔  
SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005  
Page 3  
Sheet SKU#011180 Revision 4/6/2005  
Cont.  
From  
Previous  
Page  
STEP 17: Remove the wax square and run speak-  
er wire.  
STEP 18:  
*Access Cabs O nly*  
STEP 19: With the Stealthbox and the modified  
A/C ducts in position. Place the front section of the  
center console back into the proper location. Do  
not secure at this time.  
STEP 20: Place the Stealthbox into the center  
console, outside of vehicle .  
Replace the modified A/C ducts from STEP 10,  
back into the vehicle.  
*Double Cabs O nly*  
(Stealthbox is only shown in the picture for position  
purposes.You do not have to have the Stealthbox in  
location to accomplish this step)  
The permanent removal of the rear seat 12v plug is  
neded.  
*Remember to plug in the 12v sockets.*  
(Stealthbox is only shown in the picture for position  
purposes.You do not have to have the Stealthbox in  
location to accomplish this step)  
THREADED INSERT  
STEALTHBOX WALL  
VEHICLE SHEET METAL  
FENDER WASHER  
SOCKET CUP SET SCREW  
FLAT WASHER  
LOCK WASHER  
HEX NUT  
STEP 21: Place the Stealthbox/center console into  
vehicle. Attach the speaker wire to terminal.  
STEP 22: Place Stealthbox/center console upright  
and into the proper position. Carefully guiding the  
threaded rods through the three drilled holes.  
STEP 23: Apply a supplied flat washer, lock wash-  
er and nut onto the three socket sup set screw.  
Tightly secure all three nuts. .  
Back out the three socket cup screws to 1-1/4:”.  
Pop in the four supplied black plastic push rivets,  
into the screw holes on each side of the center con-  
sole.  
Continued on Next Page ➔  
SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005  
Page 4  
Sheet SKU#011180 Revision 4/6/2005  
Cont.  
From  
Previous  
Page  
CO NGRATULATIO NS!  
INSTALL CO MPLETE.  
Included Hardware:  
3) Wax Squares  
3) 3/8”- 1-1/4” Fender Washer  
3) 3/8” Flat Washer  
3) 3/8” Split Lock Washer  
3) 3/8”-16x2-1/4” Socket Cup Set Screw  
3) 3/8”-16 Hex Nut  
STEP 24: With the Stealthbox securely mounted  
to the vehicle. Secure the plastic console to the  
floor, using the factory screws from STEP 5.  
STEP 25: Secure the front section of console with  
the factory screws, from STEP 3.  
Once both portions of the center console have  
been secured. Snap in the cup holders from  
STEP 4, front console storage door from STEP 3  
and the plastic buttons from STEP 6.  
Difficulty O f Installation:  
Mid/High Frequency Driver Information:  
Specifications:  
Enclosure Type: Sealed  
Front Location Driver Size:  
6.5”  
Driver Type: 10W3v2-D2  
Nominal Impedance: 4  
Cont. Power Handling: 300Watts  
Applicable JL Audio Products:  
VR650-CSi  
TR,VR, XR, ZR 650-CSi  
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended  
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.  
mounting plates are needed  
+12VDC  
Ground Remote  
Preamp Output Section  
Output Mode  
Bass Control  
Infrasonic Filter  
Amp LP Filter  
Mode/Slope  
Amplifier Input Section  
Input Voltage  
Input Sens. Signal Sensing  
Rear Location Driver Size:  
6.5”  
Full-Range/Low-Pass/High-Pass  
Off/30Hz  
+7  
Off/12dB/24dB  
Low/High  
Off/On  
+3  
+1  
+10  
+13  
Applicable JL Audio Products:  
TR,VR,XR 650-CXi  
JL AUDIO 250/1  
monoblock subwoofer amplifier  
Left Ch.  
Right Ch.  
LF Boost (dB) Filter Freq. (Hz)  
Left Ch.  
Right Ch.  
mounting plates are needed  
The JL Audio 250/1 is a very versatile audio component. Please consult the owners manual for detailed information  
about installing and tuning this amplifier.  
VR650-CXi  
10369 N. Commerce Pkwy, Miramar, Florida 33025-392  
Phone: 954.443.1100  
Fax: 954.443.1111  
SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005  
Page 5  
Sheet SKU#011180 Revision 4/6/2005  

Black Decker BL3900 User Manual
Black Decker CRUSH MASTER BL14501 User Manual
Burnham Independence IN7 User Manual
Bushnell Binoculars 260651 User Manual
Creative A320 User Manual
Grindmaster CRATHCO 5941 User Manual
Harbor Freight Tools 94337 User Manual
Hypertec Z0101 User Manual
JVC GR AXM300 User Manual
JVC GR DVL210 User Manual