For Your Safety
WARNING
Service
Be sure to read these notes before use
Safety Notes
• Make sure that you use your camera correctly. Read these
safety notes and your Owner’s Manual carefully before use.
• After reading these safety notes, store them in a safe place.
Servicing: Do not attempt to service this video product
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Do not use the camera in the bathroom or shower. This can
cause a fire or electric shock.
Do not use in
the bathroom
or shower
Damage Requiring Service: Unplug this video product from
the wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
• When the power-supply cord or plug is damaged
• If liquid has been spilled, or objects have fallen into the
video product.
• If the video product has been exposed to rain or water.
• If the video product has been dropped or the cabinet has
been damaged.
If the video product does not operate normally follow the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the video product to its normal operation.
Never attempt to change or take apart the camera (never
open the case) Failure to observe this precaution can
cause fire or electric shock.
About the Icons
Do not disas-
semble
The icons shown below are used in this document to indi-
cate the severity of the injury or damage that can result if the
information indicated by the icon is ignored and the product
is used incorrectly as a result.
Should the case break open as the result of a fall or other
accident, do not touch the exposed parts. Failure to observe
this precaution could result in electric shock or in injury
from touching the damaged parts. Remove the bat-
tery immediately, taking care to avoid injury or electric
shock, and take the product to the point of purchase
for consultation.
This icon indicates that death or serious injury
WARNING
Do not touch
internal
parts
can result if the information is ignored.
This icon indicates that personal injury or
CAUTION material damage can result if the information
is ignored.
Do not change, heat or unduly twist or pull the connection
cord and do not place heavy objects on the connection cord.
These actions could damage the cord and cause a fire
or electric shock. If the cord is damaged, contact your
FUJIFILM dealer.
The icons shown below are used to indicate the nature of the
instructions which are to be observed.
Triangular icons tell you that this information requires
attention (“Important”).
When the video product exhibits a distinct change in perfor-
mance — this indicates a need for service.
Do not place the camera on an unstable surface. This can
cause the camera to fall or tip over and cause injury.
Circular icons with a diagonal bar tell you that the action
indicated is prohibited (“Prohibited”).
Replacement Parts: When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
Never attempt to take pictures while in motion. Do not
use the camera while walking or driving. This can
result in you falling down or being involved in a traf-
fic accident.
Filled circles with an exclamation mark indicate an ac-
tion that must be performed (“Required”).
Do not touch any metal parts of the camera during a thun-
derstorm. This can cause an electric shock due to in-
duced current from the lightning discharge.
WARNING
Safety Check: Upon completion of any service or repairs to
this video product, ask the service technician to perform
safety checks to determine that the video product is in
proper operating condition.
If a problem arises, turn the camera off, remove the bat-
tery, and disconnect and unplug the AC power adapter.
Continued use of the camera when it is emitting
smoke, is emitting any unusual odor, or is in any other
abnormal state can cause a fire or electric shock. Con-
Do not use the battery except as specified. Load the bat-
tery as shown by the indicator.
Unplug
from power
socket
Do not heat, change or take apart the battery. Do not drop
or subject the battery to impacts. Do not store the battery
with metallic products. Any of these actions can cause
the battery to burst or leak and cause fire or injury as
a result.
tact your FUJIFILM dealer.
Do not allow water or foreign objects to enter the camera.
If water or foreign objects get inside the camera, turn
the camera off, remove the battery, and disconnect
and unplug the AC power adapter. Continued use of
the camera can cause a fire or electric shock. Contact
your FUJIFILM dealer.
Use only batteries or AC power adapters specified for use
with this camera. Do not use voltages other than the power
supply voltage shown. The use of other power sources
can cause a fire.
iii
For Your Safety
The Battery and Power Supply
Note: Check the type of battery used in your camera and
read the appropriate sections.
WARNING
CAUTION
If the battery leaks and fluid gets in contact with your eyes,
skin or clothing, flush the affected area with clean water
and seek medical attention or call an emergency number
right away.
When you are cleaning the camera or you do not plan to use
the camera for an extended period, remove the battery and
disconnect and unplug the AC power adapter. Failure to do
so can cause a fire or electric shock.
The following describes the proper use of batteries and how
to prolong their life. Incorrect use can shorten battery life or
cause leakage, overheating, fire, or explosion.
Do not use the charger to charge batteries other than those
specified here. The supplied charger is for use only with
batteries of the type supplied with the camera. Using
the charger to charge conventional batteries or other
types of rechargeable batteries can cause the battery to
leak, overheat or burst.
When charging ends, unplug the charger from the power
socket. Leaving the charger plugged into the power
socket can cause a fire.
Li-ion Batteries
Read this section if your camera uses a rechargeable
Using a flash too close to a person’s eyes may temporarily
affect the eyesight. Take particular care when photo-
graphing infants and young children.
Li-ion battery.
The battery is not charged at shipment. Charge the battery
before use. Keep the battery in its case when not in use.
When carrying the battery, install it in a digital camera or
keep it in the hard case. When storing the battery, keep it
in the hard case. When discarding, cover the battery termi-
nals with insulation tape. Contact with other metallic
objects or batteries could cause the battery to ignite
or burst.
When a memory card is removed, the card could come out
of the slot too quickly. Use your finger to hold it and gently
release the card. Injury could result to those struck by
the ejected card.
■ Notes on the Battery
The battery gradually loses its charge when not in use.
Charge the battery one or two days before use.
Request regular internal testing and cleaning for your
camera. Build-up of dust in your camera can cause a
fire or electric shock. Contact your FUJIFILM dealer to
request internal cleaning every two years. Please note
that this service is not free of charge.
Battery life can be extended by turning the camera off when
not in use.
Keep memory cards out of the reach of small children. Be-
cause memory cards are small, they can be swallowed
by children. Be sure to store memory cards out of the
reach of small children. If a child swallows a memory
card, seek medical attention or call an emergency
number.
Battery capacity decreases at low temperatures; a depleted
battery may not function at when cold. Keep a fully charged
spare battery in a warm place and exchange as necessary,
or keep the battery in your pocket or other warm place and
insert it in the camera only when shooting. Do not place
the battery in direct contact with hand warmers or other
heating devices.
Danger of explosion if battery is incorrectly replaced. Re-
place only with the same or equivalent type.
CAUTION
Do not use this camera in locations affected by oil fumes,
steam, humidity or dust. This can cause a fire or elec-
tric shock.
■ Charging the Battery
Charge the battery in the supplied battery charger. Charging
times will increase at ambient temperatures below +10 °C
(+50 °F) or above +35 °C (+95 °F). Do not attempt to charge
the battery at temperatures above 40 °C (+104 °F); at tem-
peratures below 0 °C (+32 °F), the battery will not charge.
Do not leave this camera in places subject to extremely high
temperatures. Do not leave the camera in locations
such as a sealed vehicle or in direct sunlight. This can
cause a fire.
Keep out of the reach of small children. This product
could cause injury in the hands of a child.
Do not attempt to recharge a fully charged battery. The bat-
tery does not however need to be fully discharged before
charging.
Do not place heavy objects on the camera. This can cause
the heavy object to tip over or fall and cause injury.
Do not move the camera while the AC power adapter is still
connected. Do not pull on the connection cord to disconnect
the AC power adapter. This can damage the power cord
or cables and cause a fire or electric shock.
The battery may be warm to the touch immediately after
charging or use. This is normal.
■ Battery Life
At normal temperatures, the battery can be recharged about
300 times. A noticeable decrease in the length of time the
battery will hold a charge indicates that it has reached the
Do not cover or wrap the camera or the AC power adapter in
a cloth or blanket. This can cause heat to build up and
distort the casing or cause a fire.
iv
For Your Safety
end of its service life and should be replaced.
move the batteries. Note that the camera clock will be reset. arately). Batteries may become warm to the touch after charg-
• The batteries may be warm to the touch immediately after ing. Refer to the instructions provided with the charger for more
use. Turn the camera off and allow the batteries to cool information. Use the charger with compatible batteries only.
■ Storage
Performance may be impaired if the battery is left unused
for extended periods when fully charged. Run the battery
flat before storing it.
before handling.
• Battery capacity tends to decrease at low temperatures.
Ni-MH batteries gradually lose their charge when not in use.
■ Disposal
Keep spare batteries in a pocket or other warm place and
exchange as necessary. Cold batteries may recover some
of their charge when warmed.
• Fingerprints and other stains on the battery terminals
can impair battery performance. Thoroughly clean the
terminals with a soft, dry cloth before inserting them in
the camera.
If the camera will not be used for an extended period, re-
move the battery and store it in a dry place with an ambient
temperature of from +15 °C to +25 °C (+59 °F to +77 °F). Do
not store in locations exposed to extremes of temperature.
Dispose of used batteries in accord with local regulations.
AC Power Addaapptteerrss ((AAvvaaiillaabbllee SSeparately)
This section applies to all camera models. Use only
FUJIFILM AC power adapters designated for use with this
camera. Other adapters could damage the camera.
• The AC power adapter is for indoor use only.
• Be sure the DC plug is securely connected to the camera.
• Turn the camera off before disconnecting the adapter. Dis-
connect the adapter by the plug, not the cable.
• Do not use with other devices.
■ Cautions: Handling the Battery
• Do not transport or store with metal objects such as neck-
laces or hairpins.
• Do not expose to flame or heat.
If the batteries leak, clean the battery compartment
thoroughly before inserting new batteries.
• Do not disassemble or modify.
If fluid from the battery comes into contact with
skin or clothing, flush the affected area with water.
If fluid enters your eyes, immediately flush the affected
area with water and seek medical attention. Do not rub
your eyes. Failure to observe this precaution could result
in permanent visual impairment.
• Use with designated chargers only.
• Dispose of used batteries promptly.
• Do not drop or subject to strong physical shocks.
• Do not expose to water.
• Keep the terminals clean.
• The battery and camera body may become warm to the
touch after extended use. This is normal.
• Do not disassemble.
• Do not expose to high heat and humidity.
• Do not subject to strong physical shocks.
• The adapter may hum or become hot to the touch during
use. This is normal.
• If the adapter causes radio interference, reorient or relocate
the receiving antenna.
■ Ni-MH Batteries
The capacity of Ni-MH batteries may be temporarily reduced
AA Alkalline/Rechargeable Ni-MH Batteries
Read this section if your camera uses AA alkaline or re- when new, after long periods of disuse, or if they are repeat-
chargeable AA Ni-MH batteries. Information on compat- edly recharged before being fully discharged. This is nor-
ible battery types may be found elsewhere in the camera mal and does not indicate a malfunction. Capacity can be
manual.
increased by repeatedly discharging the batteries using the
discharge option in the camera setup menu and recharging
them using a battery charger.
■ Cautions: Handling the Batteries
• Do not expose to water, flame, or heat, or store in warm or
humid conditions.
• Do not transport or store with metal objects such as neck-
laces or hairpins.
Q
CAUTION: Do not use the discharge option with alkaline
batteries.
The camera draws a small amount of current even when off.
• Do not disassemble or modify the batteries or battery Ni-MH batteries that have been left in the camera for an ex-
casing.
tended period may be drawn down to the point that they no
longer hold a charge. Battery performance may also drop if
• Do not subject to strong physical shocks.
• Do not use batteries that are leaking, deformed, or discol- the batteries are run down in a device such as a flashlight. Use
ored.
the discharge option in the camera setup menu to discharge
Ni-MH batteries. Batteries that no longer hold charge
even after repeatedly being discharged and recharged have
• Keep out of reach of infants and small children.
• Insert in the correct orientation.
a
• Do not mix old and new batteries, batteries with different reached the end of their service life and must be replaced.
charge levels, or batteries of different types.
• If the camera will not be used for an extended period, re-
Ni-MH batteries can be recharged in a battery charger (sold sep-
v
For Your Safety
Although the display is manufactured using extremely high-
precision technology, it may contain pixels that are always lit
or that do not light. This is not a malfunction, and images
recorded with the product are unaffected.
Using the Camera
IMPORTANT NOTICE: Read Before Using the Software
Do not aim the camera at extremely bright light sources,
such as the sun in a cloudless sky. Failure to observe this
precaution could damage the camera image sensor.
Direct or indirect export, in whole or in part, of licensed soft-
ware without the permission of the applicable governing
bodies is prohibited.
Trademarkk Information
Take Test Shots
xD-Picture Card and E are trademarks of FUJIFILM
Corporation. The typefaces included herein are solely de-
veloped by DynaComware Taiwan Inc. Macintosh, Quick-
Time, and Mac OS are trademarks of Apple Inc. in the U.S.A.
and other countries. Windows 7, Windows Vista, and the
Windows logo are trademarks of the Microsoft group of
companies. Adobe and Adobe Reader are either trademarks
or registered trademarks of Adobe Systems Incorporated in
the U.S.A. and/or other countries. The SDHC and SDXC logos
are trademarks of SD-3C, LLC. The HDMI logo is a trademark.
YouTube is a trademark of Google Inc. All other trade names
mentioned in this manual are the trademarks or registered
trademarks of their respective owners.
Before taking photographs on important occasions (such as
at weddings or before taking the camera on a trip), take a
test shot and view the results to ensure that the camera is
functioning normally. FUJIFILM Corporation can not accept
liability for damages or lost profits incurred as a result of
product malfunction.
Notes on Copyright
Unless intended solely for personal use, images recorded us-
ing your digital camera system cannot be used in ways that
infringe copyright laws without the consent of the owner.
Note that some restrictions apply to the photographing of
stage performances, entertainments, and exhibits, even
when intended purely for personal use. Users are also asked
to note that the transfer of memory cards containing images
or data protected under copyright laws is only permissible
within the restrictions imposed by those copyright laws.
Electrical Innterference
This camera may interfere with hospital or aviation equip-
ment. Consult with hospital or airline staff before using the
camera in a hospital or on an aircraft.
Haandling
Color Television Systems
To ensure that images are recorded correctly, do not subject
the camera to impact or physical shocks while images are
being recorded.
NTSC (National Television System Committee) is a color televi-
sion telecasting specification adopted mainly in the U.S.A., Can-
ada, and Japan. PAL (Phase Alternation by Line) is a color televi-
sion system adopted mainly in European countries and China.
Liquid CCrystal
In the event that the display is damaged, care should be
taken to avoid contact with liquid crystal. Take the urgent
action indicated should any of the following situations arise:
Electrical Innterference
Exif Print is a newly revised digital camera file format in
which information stored with photographs is used for opti-
mal color reproduction during printing.
•
•
•
If liquid crystal comes in contact with your skin, clean the
area with a cloth and then wash thoroughly with soap and
running water.
If liquid crystal enters your eyes, flush the affected eye with
clean water for at least 15 minutes and then seek medical
assistance.
If liquid crystal is swallowed, rinse your mouth thoroughly
with water. Drink large quantities of water and induce
vomiting, then seek medical assistance.
vi
For Your Safety
Notes on the Grant: To comply with Part 15 of the FCC Rules,
this product must be used with a Fujifilm-specified ferrite-
core A/V cable, USB cable, and DC supply cord.
EC Declaaratioon of Coonformity
We
NOTICES
To prevent fire or shock hazard, do not expose the unit
to rain or moisture.
Name:
Address:
FUJIFILM Electronic Imaging Europe GmbH
Benzstrasse 2 47533 Kleve, Germany
For Customers in Canada
CAUTION: This Class B digital apparatus complies with Cana-
dian ICES-003.
declare that the product
Product Name: FUJIFILM DIGITAL CAMERA FinePix X100
Manufacturer’s
Please read the “Safety Notes” and make sure you un-
derstand them before using the camera.
Perchlorate Material—special handling may apply. See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
Name:
Manufacturer’s 7-3, AKASAKA 9-CHOME, MINATO-KU,
Address: TOKYO, 107-0052 JAPAN
conforms to the following Standards:
FUJIFILM Corporation
Disposall of Electrical and Electronic Equipment in Private
Houseeholds
For Customers in the U. S. A.
In the European Union, Norway, Iceland and Liechten-
stein: This symbol on the product, or in the man-
ual and in the warranty, and/or on its packaging
indicates that this product shall not be treated as
household waste. Instead it should be taken to
an applicable collection point for the recycling
of electrical and electronic equipment.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Safety:
EMC:
EN60065: 2002 + A1: 2006 + A11: 2008
EN55022: 2006 + A1: 2007 Class B
EN55024: 1998 + A1: 2001 + A2: 2003
EN61000-3-2: 2006
FCC Statement: This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
EN61000-3-3: 1995 + A1: 2001 + A2: 2005
following the provision of the EMC Directive (2004/108/EC)
and Low Voltage Directive (2006/95/EC).
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences to the en-
vironment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
CAUTION: This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the fol-
lowing measures:
Kleve, Germany February 1, 2011
This symbol on the batteries or accumulators in-
dicates that those batteries shall not be treated
as household waste.
Place
Date
Signature, Managing
Director
If your equipment contains easy removable batteries or
accumulators please dispose these separately according to
your local requirements.
The recycling of materials will help to conserve natural re-
sources. For more detailed information about recycling this
product, please contact your local city office, your household
waste disposal service or the shop where you purchased the
product.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
In Countries Outside the European Union, Norway, Iceland and
Liechtenstein: If you wish to discard this product, including
the batteries or accumulators, please contact your local au-
thorities and ask for the correct way of disposal.
• You are cautioned that any changes or modifications not
expressly approved in this manual could void the user’s
authority to operate the equipment.
vii
About This Manual
Before using the camera, read this manual and the warnings in“For Your Safety”(Pii). For information
on specific topics, consult the sources below.
Task Index .............................................................................................. Pix Table of Contents ................................................. Pxii
Know what you want to do but don’t know the The “Table of Contents” gives an overview of the
name for it? Find the answer in the“Task Index.” entire manual. The principal camera operations
are listed here.
Troubleshooting ................................................ P105 Warning Messaggeess aanndd Displays ......................... P109
Having a specific problem with the camera? Find out what’s behind that flashing icon or error
Find the answer here.
message in the display.
Glossary............................................................ P113 Reessttrriiccttiioonnss oonn CCaammeerraa SSettings.......................... P120
The meanings of some technical terms may be See page 120 for restrictions on the options avail-
found here.
able in each shooting mode.
Memoryy Caarrds
Pictures can be stored in the camera’s internal memory or on optional SD, SDHC, and SDXC memory cards (P15),
referred to in this manual as“memory cards.”
viii
Task Index
Find items by task.
■ Taking Photographs
■ Adjusting Exposure
The optical viewfinder................................................. 6, 18
Power management.......................................................... 23
Shutter sounds...................................................................... 22
The self-timer......................................................................... 44
ISO sensitivity......................................................................... 51
Auto ISO .................................................................................... 84
Metering.................................................................................... 52
Shutter speed and aperture ......................................... 28
Program autoexposure.................................................... 24
Shutter priority autoexposure..................................... 25
Aperture priority autoexposure.................................. 26
Manual exposure................................................................. 27
Long time exposures......................................................... 29
Exposure lock......................................................................... 46
Exposure compensation................................................. 30
■ Choosing Image Quality and Size
Image size ................................................................................ 69
Image quality......................................................................... 70
RAW images............................................................................ 56
Color space.............................................................................. 86
■ Focusing
Focus mode ............................................................................ 48
Focus frame selection....................................................... 50
Focus lock................................................................................. 46
Manual focus.......................................................................... 48
■ Adjusting Colors to the Light Source
White balance........................................................................ 35
Film simulation...................................................................... 54
Dynamic range ..................................................................... 70
Color/tone/sharpness................................................70, 71
ix
Task Index
■ Choosing a Drive Mode
■ Custom Settings
Burst photography.............................................................. 37
Bracketing ................................................................................ 38
Panoramas ............................................................................... 39
Movies........................................................................................ 42
Assigning a role to the Fn button.............................. 53
Saving and recalling settings....................................... 55
■ Using the Flash
The built-in flash.............................................................. 2, 32
Flash photography ............................................................. 32
Flash mode.............................................................................. 32
Flash compensation .......................................................... 71
Optional flash units..................................................71, 100
x
Caring for the Camera
For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body after each
use. Do not use alcohol, thinner, or other volatile chemicals, which could discolor or deform the leather
on the camera body. Any liquid on the camera should be removed immediately with a soft, dry cloth.
Use a blower to remove dust from the lens and monitor, then gently wipe with a soft, dry cloth. Any
remaining stains can be removed by wiping gently with a piece of FUJIFILM lens-cleaning paper to
which a small amount of lens-cleaning fluid has been applied. Care should be taken to avoid scratch-
ing the lens or monitor.
xi
Table of Contents
For Your Safety.....................................................................................ii
IMPORTANT SAFETY INSTRUCTIONS.........................................ii
Safety Notes.......................................................................................iii
NOTICES..............................................................................................vii
About This Manual..........................................................................viii
Task Index .............................................................................................ix
Caring for the Camera .....................................................................xi
Basic Setup ......................................................................................... 17
Choosing a Display ......................................................................... 18
Using the Hybrid Viewfinder..................................................... 19
Focusing the Viewfinder ............................................................. 19
The DISP/BACK Button....................................................................... 20
Optical Viewfinder: Shooting................................................. 20
Electronic Viewfinder: Shooting............................................ 20
LCD Monitor: Shooting............................................................. 20
Electronic Viewfinder/LCD Monitor: Playback................. 21
Choosing a Shutter Sound .......................................................... 22
Power Management....................................................................... 23
GOVF POWER SAVE MODE...................................................... 23
HQUICK START MODE............................................................... 23
Before You Begin
Symbols and Conventions..............................................................1
Supplied Accessories........................................................................1
Parts of the Camera...........................................................................2
The Command Dial ..........................................................................4
The Command Control...................................................................5
Camera Displays................................................................................6
Shooting: Optical Viewfinder ....................................................6
Shooting: Electronic Viewfinder...............................................7
Shooting: LCD Monitor................................................................7
Playback: Electronic Viewfinder/LCD Monitor....................8
Taking Phhotoographs
Program AE (P).................................................................................. 24
Shutter-Priority AE (S) ................................................................... 25
Aperture-Priority AE (A) ............................................................... 26
Manual Exposure (M)..................................................................... 27
Shutter Speed and Aperture...................................................... 28
Long Time-Exposures (T/B)......................................................... 29
Time (T).............................................................................................. 29
Bulb (B)............................................................................................... 29
Exposure Compensation.............................................................. 30
Focusing and Taking Pictures .................................................... 31
Firstt SSteepps
Attaching the Strap ...........................................................................9
Charging the Battery ..................................................................... 11
Inserting the Battery and a Memory Card........................... 12
Compatible Memory Cards..................................................... 15
Turning the Camera on and Off ................................................ 16
xii
Table of Contents
Moorre on Phhotoography
Viewing Pictures
NUsing the Flash (Super-Intelligent Flash)......................... 32
FMacro Mode (Close-ups)......................................................... 34
White Balance ................................................................................... 35
IContinuous Shooting (Burst Mode).................................. 37
Bracketing........................................................................................... 38
Panoramas.......................................................................................... 39
FRecording High-Definition (HD) Movies......................... 42
Before Recording ........................................................................... 43
hUsing the Self-Timer ................................................................. 44
Focus/Exposure Lock ..................................................................... 46
Focus Mode ........................................................................................ 48
Focus Frame Selection .................................................................. 50
Sensitivity ........................................................................................... 51
Metering.............................................................................................. 52
The Fn Button.................................................................................... 53
Film Simulation ................................................................................ 54
Saving Settings................................................................................. 55
The RAW Button............................................................................... 56
The ND Filter...................................................................................... 57
Viewing Pictures Full Frame ....................................................... 58
Playback Zoom ............................................................................... 59
Multi-Frame Playback................................................................... 60
Viewing Movies ................................................................................ 61
Image Search..................................................................................... 62
mPhotoBook Assist...................................................................... 63
Creating a PhotoBook.................................................................. 63
Viewing Photobooks .................................................................... 64
Editing and Deleting Photobooks........................................... 64
Viewing Panoramas........................................................................ 65
Viewing Pictures Taken in a Single Burst.............................. 66
xDeleting Pictures....................................................................... 67
Creating JPEG Copies of RAW Pictures.................................. 68
xiii
Table of Contents
Using the Menus: Playback Mode............................................ 73
Playback Menu Options .............................................................. 73
mPHOTOBOOK ASSIT.............................................................. 73
tIMAGE SEARCH...................................................................... 73
AERASE........................................................................................ 73
jMARK FOR UPLOAD TO ...................................................... 74
ISLIDE SHOW ........................................................................... 75
jRAW CONVERSION............................................................... 75
BRED EYE REMOVAL............................................................... 75
DPROTECT .................................................................................. 76
GCROP.......................................................................................... 76
eRESIZE ....................................................................................... 77
CIMAGE ROTATE....................................................................... 77
ECOPY.......................................................................................... 78
KPRINT ORDER (DPOF).......................................................... 78
JDISP ASPECT........................................................................... 78
Menus
Using the Menus: Shooting Mode........................................... 69
Shooting Menu Options.............................................................. 69
BSELF-TIMER.............................................................................. 69
NISO.............................................................................................. 69
OIMAGE SIZE.............................................................................. 69
TIMAGE QUALITY .................................................................... 70
UDYNAMIC RANGE.................................................................. 70
PFILM SIMULATION ................................................................ 70
tND FILTER................................................................................. 70
dWB SHIFT.................................................................................. 70
fCOLOR....................................................................................... 70
HSHARPNESS............................................................................. 71
rHIGHLIGHT TONE.................................................................. 71
sSHADOW TONE ..................................................................... 71
hNOISE REDUCTION............................................................... 71
FAF MODE.................................................................................. 71
IFLASH........................................................................................ 71
gEXTERNAL FLASH ................................................................. 71
uSELECT CUSTOM SETTING ................................................ 72
KEDIT/SAVE CUSTOM SETTING.......................................... 72
vDISP. CUSTOM SETTING ..................................................... 72
xiv
Table of Contents
The Setup Menu............................................................................... 79
Using the Setup Menu................................................................. 79
Setup Menu Options .................................................................... 80
FDATE/TIME............................................................................... 80
NTIME DIFFERENCE................................................................. 80
La................................................................................ 80
oSILENT MODE......................................................................... 80
RRESET......................................................................................... 80
KFORMAT.................................................................................... 81
AIMAGE DISP.............................................................................. 81
BFRAME NO............................................................................... 82
GOPERATION VOL.................................................................... 82
HSHUTTER VOLUME ............................................................... 82
eSHUTTER SOUND.................................................................. 82
IPLAYBACK VOLUME............................................................. 82
JLCD BRIGHTNESS.................................................................. 83
MAUTO POWER OFF................................................................ 83
GOVF POWER SAVE MODE................................................... 83
HQUICK START MODE............................................................ 83
FFn BUTTON.............................................................................. 83
NISO AUTO CONTROL............................................................ 84
BRED EYE REMOVAL............................................................... 84
CAF ILLUMINATOR .................................................................. 85
kAE/AF-LOCK MODE.............................................................. 85
vAE/AF-LOCK BUTTON.......................................................... 85
jFOCUS CHECK........................................................................ 85
IFOCUS RING............................................................................ 85
MFOCUS SCALE UNITS ........................................................... 85
zFRAMING GUIDLINE ............................................................ 86
JCOLOR SPACE......................................................................... 86
KLONG EXPOSURE NR ........................................................... 86
nSAVE ORG IMAGE.................................................................. 87
mAUTOROTATE PB ................................................................... 87
OBACKGROUND COLOR........................................................ 87
cGUIDANCE DISPLAY............................................................. 87
GCORRECTED AF FRAME...................................................... 87
xv
Table of Contents
Connections
Techniccaall NNoottes
Viewing Pictures on TV ................................................................. 88
Printing Pictures via USB ............................................................. 89
Connecting the Camera.............................................................. 89
Printing Selected Pictures .......................................................... 89
Printing the DPOF Print Order .................................................. 90
Creating a DPOF Print Order...................................................... 91
WITH DATE s/WITHOUT DATE........................................... 92
RESET ALL....................................................................................... 93
Viewing Pictures on a Computer.............................................. 94
Windows: Installing MyFinePix Studio .................................. 94
Macintosh: Installing FinePixViewer....................................... 96
Connecting the Camera.............................................................. 98
Optional Accessories....................................................................100
Accessories from FUJIFILM.......................................................100
Attaching Adapter Rings and Lens Hoods.........................101
Connecting the Camera to Other Devices.........................102
Caring for the Camera .................................................................103
Storage and Use ...........................................................................103
Cleaning ..........................................................................................104
Traveling..........................................................................................104
Troubleshooting
Problems and Solutions .............................................................105
Warning Messages and Displays............................................109
Appeenndix
Glossary .............................................................................................113
Internal Memory/Memory Card Capacity..........................114
Specifications..................................................................................115
Restrictions on Camera Settings............................................120
xvi
Before You Begin
Symbols andd Convventions
The following symbols are used in this manual:
QThis information should be read before use to ensure correct operation.
RAdditional information that may be helpful when using the camera.
POther pages in this manual on which related information may be found.
Menus and other text in the displays are shown in bold. In the illustrations in this manual, displays may
be simplified for explanatory purposes.
Supplied Accessories
The following items are included with the camera:
NP-95 rechargeable battery
BC-65N battery charger
Lens cap
USB cable
• Owner’s Manual (this
manual)
• Shoulder strap
• Protective covers (× 2)
CD-ROM
Clip attaching tool
Metal strap clips (× 2)
1
Parts of the Camera
For more information, refer to the page listed to the right of each item.
1 Shutter button..................................................31 12 Lens................................................................104 22 Eye sensor.........................................................18
2 Exposure compensation dial .............................30 13 Front ring........................................................101 23 Command control ...............................................5
3 Shutter speed dial................................. 24, 25, 27 14 AF-assist illuminator.........................................85 24 Connector cover.................................... 88, 89, 98
4 Hot shoe ...................................................71, 102
Self-timer lamp ................................................45 25 Cable channel cover for DC coupler
5 Flash.................................................................32 15 Viewfinder selector...........................................19 26 Battery-chamber cover latch ............................12
6 Microphone (L) .................................................42 16 Microphone (R).................................................42 27 Battery-chamber cover.....................................12
7 Viewfinder window ....................................18, 19 17 ON/OFF switch.................................................16 28 Tripod mount
8 Strap eyelet ........................................................9 18 Fn (Function) button........................................53 29 Speaker.............................................................61
9 Focus mode selector .........................................48 19 Battery latch...............................................12, 14 30 LCD monitor....................................................7, 8
10 Aperture ring........................................ 24, 26, 27 20 Memory card slot..............................................13 31 USB connector ............................................89, 98
11 Focus ring .........................................................48 21 Battery chamber...............................................12 32 HDMI mini connector........................................88
2
Parts of the Camera
36 AF (autofocus) button ......................................50
n(playback zoom out) button..................59, 60
37 VIEW MODE button .........................................18
38 AFL/AEL (focus lock/exposure) button.......46, 48
39 Indicator lamp (see below)
40 MENU/OK button...............................................4
41 Command dial ....................................................4
42 RAW button .....................................................56
43 DISP (display)/BACK button ............................20
33 Diopter adjustment control...............................19 35 AE (autoexposure) button ................................52
34 a(playback) button.......................................58
k(playback zoom in) button....................59, 60
Thhee IInndicator Lamp
The indicator lamp shows camera status as follows:
Indicator lamp
Indicator lamp
Glowwss ggrreen
Blinks green
Caammera sstatus
Focus locked.
Blur, focus, or exposure warning. Picture can be taken.
Blinks green and orange Recording pictures. Additional pictures can be taken.
Glowwss oorraannggee
Blinks orange
Blinks red
Recording pictures. No additional pictures can be taken at this time.
Flash charging; flash will not fire when picture is taken.
Lens or memory error.
R Warnings may also appear in the display (P109)
3
Parts of the Camera
The Command Dial
Rotate the command dial or press it up ( ), right ( ), down ( ), or left ( ) to highlight items and
q
w
e
r
press MENU/OK ( ) to select.
t
The command dial also serves as the following buttons:
: b(delete) button (P58)/DRIVE button (P37)
: N(flash) button (P32)
: WB (white balance) button (P35)
: F(macro) button (P34)
q
w
e
r
You can also rotate the command dial to choose a combination of shutter speed and aperture
/
(program shift; P24) or to adjust shutter speed in increments of 1 3EV (P25, 27).
Coontrol Loock
To lock the RAW button and prevent the command dial being used as a DRIVE, flash, white balance, or macro
button, press MENU/OK until X is displayed. This prevents accidental operation of these controls during shooting.
The controls can be unlocked by pressing MENU/OK until X is no longer displayed.
4
Parts of the Camera
The Command Control
Pressing the command control left or right performs the same function as pressing the command dial
left or right. It can also be used to choose a combination of shutter speed and aperture in place of the
/
command dial (program shift; P24) or to adjust aperture in increments of 1 3EV (P26, 27).
You can also press the center of the command dial to zoom in on the focus area selected for manual
focus in the electronic viewfinder or LCD monitor, or to zoom in on the active focus point during play-
back or (if CONTINUOUS is selected for AIMAGE DISP. in the setup menu; P81) image review (press
again to cancel zoom).
5
Parts of the Camera
Camera Displays
The following types of indicator may be displayed during shooting and playback. Indicators vary with
camera settings.
■ Shooting: Optical Viewfinder
1 Manual focus indicator .....................................48 13 Virtual horizon..................................................72
2 Flash mode .......................................................32 14 Temperature warning .....................................112
3 Metering...........................................................52 15 Bright frame
100
4 White balance...................................................35 16 Distance indicator.......................................48, 85
5 Film simulation.................................................54 17 Sensitivity.........................................................51
6 Dynamic range .................................................70 18 Aperture ............................................... 24, 26, 27
7 ND (Neutral Density) filter indicator .................57 19 Shutter speed ....................................... 24, 25, 27
8 Internal memory indicator*
20 Shooting mode............................... 24, 25, 26, 27
9 Number of available frames............................114 21 Histogram.........................................................21
10 Image quality and size................................69, 70 22 Exposure compensation/
11 Battery level .....................................................16
exposure indicator ......................................27, 30
12 Focus frame ................................................46, 50
*a: indicates that no memory card is inserted and that
pictures will be stored in the camera’s internal memory
(P13).
6
Parts of the Camera
■ Shooting: Electronic Viewfinder
1 Manual focus indicator .....................................48 16 Distance indicator.......................................48, 85
2 Metering...........................................................52 17 Sensitivity.........................................................51
3 Continuous mode .............................................37 18 Blur warning...................................................109
4 Silent mode indicator .......................................22 19 Aperture ............................................... 24, 26, 27
5 Virtual horizon..................................................72 20 Shutter speed ....................................... 24, 25, 27
6 Internal memory indicator*
21 Shooting mode.................................................24
7 Focus warning ..........................................31, 109 22 Histogram.........................................................21
8 Number of available frames............................114 23 Exposure compensation/
9 Temperature warning .....................................112
exposure indicator ......................................27, 30
10 Image quality and size................................69, 70 24 Self-timer indicator ..........................................44
11 Dynamic range .................................................70 25 Macro (close-up) mode.....................................34
12 Film simulation.................................................54 26 Flash mode .......................................................32
13 White balance...................................................35 27 Depth-of-field preview.....................................26
14 Battery level .....................................................16 28 Focus frame ................................................46, 50
15 ND (Neutral Density) filter indicator .................57
*a: indicates that no memory card is inserted and that
pictures will be stored in the camera’s internal memory
(P13).
■ Shooting: LCD Monitor
1 Flash mode .......................................................32 13 White balance...................................................35
2 Macro (close-up) mode.....................................34 14 Battery level .....................................................16
3 Metering...........................................................52 15 Sensitivity.........................................................51
4 Continuous mode .............................................37 16 Aperture ............................................... 24, 26, 27
5 Silent mode indicator .......................................22 17 Focus frame/focus point .............................46, 50
6 ND (Neutral Density) filter indicator .................57 18 Shutter speed ....................................... 24, 25, 27
7 Internal memory indicator*
19 Shooting mode.................................................24
8 Number of available frames............................114 20 Focus mode ......................................................48
9 Temperature warning .....................................112 21 Self-timer indicator ..........................................44
10 Image quality and size................................69, 70 22 Exposure compensation/
11 Dynamic range .................................................70
12 Film simulation.................................................54
exposure indicator ......................................27, 30
*a: indicates that no memory card is inserted and that
pictures will be stored in the camera’s internal memory
(P13).
7
Parts of the Camera
■ Playback: Electronic Viewfinder/LCD Monitor
1 Rating...............................................................58 6 Playback mode indicator...................................58
2 Red-eye removal indicator................................75 7 Mark for upload to............................................74
3 Silent mode indicator .......................................22 8 Photobook assist indicator................................63
4 Gift image.........................................................58 9 DPOF print indicator .........................................90
5 Frame number..................................................82 10 Protected image ...............................................76
3
8
First Steps
Attachinngg tthhee SStrap
Attach the strap clips to the camera and then attach the strap.
Open a strap clip.
Use the clip attaching tool to open a strap clip
as shown.
Pass the clip through the eyelet.
Rotate the clip fully through
the eyelet until it clicks
closed.
1
3
Attach a protective cover.
4
Place a protective cover over the eyelet as
shown, with the black side of the cover toward
the camera. Repeat Steps 1–4 for the second
eyelet.
Q Keep the tool in a safe place. You will need it to
open the strap clips when removing the strap.
Place the strap clip on an eyelet.
Hook the strap eyelet in the clip opening. Re-
move the tool, using the other hand to keep
the clip in place.
2
9
Attaching the Strap
Insert the strap.
Insert the strap through a protective cover
Fasten the strap.
Fasten the strap as shown. Repeat Steps 5–6
5
6
and strap clip.
for the second eyelet.
Q To avoid dropping the camera, be sure the strap is
correctly secured.
10
Chhaarrggiinngg the Batteerryy
The battery is not charged at shipment. Charge
the battery before use.
Plug the charger in.
Plug the charger into a power outlet. The
2
charging indicator will light.
Place the battery in the supplied battery
charger.
Insert the battery in the orientation indicated
1
Thhee CCharggiinngg IInnddicator
The charging indicator shows battery charge sta-
by the DFClabels.
tus as follows:
Charging
indicator
Battery
Charge
Battery status
Action
Battery not
inserted.
Battery fully
charged.
Arrow
lamp
Insert the battery.
Off
Reemmoove the battery.
—
On
Battery charging.
DFC
Unplug the charger
and remove the
battery.
label
DFClabel
Blinks
Battery fault.
Battery charger
Charge the battery.
3
The camera uses an NP-95 rechargeable battery.
Remove the battery when charging is com-
plete. See the specifications (P118) for charg-
ing times (note that charging times increase
at low temperatures).
R Attach the supplied adapter
before charging the battery
(the adapter is attached at
shipment).
Q Unplug the charger when it is not in use.
Adapter
11
Innsseertinng the Baatttterryy aanndd aa MMemory Cardd
Although the camera can store pictures in internal memory, optional SD, SDHC, and SDXC memory
cards (sold separately) can be used to store additional pictures. After charging the battery, insert the
battery and memory card as described below.
Open the battery-chamber cover.
Insert the battery.
1
2
Insert the battery as shown inside the battery
chamber, using the battery to keep the bat-
tery latch pressed to one side.
Arrow
R Be sure the camera is off before opening the
battery-chamber cover.
Q Do not open the battery-chamber cover when
the camera is on. Failure to observe this precau-
tion could damage image files or memory cards.
Q Do not use excessive force when handling the
battery-chamber cover.
Battery latch
Q Insert the battery in the correct orientation. Do
not use force or attempt to insert the battery up-
side down or backwards. The battery will slide in
easily in the correct orientation.
12
Inserting the Battery and a Memory Card
Q SD/SDHC/SDXC memo-
Insert the memory card.
Holding the memory
card in the orientation
shown at right, slide
it in until it clicks into
place at the back of
the slot.
3
ry cards can be locked,
making it impossible to
format the card or to
record or delete images.
Before inserting a memory card, slide the write-
protect switch to the unlocked position.
Write-protect switch
Click
Close the battery-chamber cover.
4
Q Be sure card is in the correct orientation; do not
insert at an angle or use force. If the memory
card is not correctly inserted or no memory card
is inserted, awill appear in the display and in-
ternal memory will be used for recording and
playback.
13
Inserting the Battery and a Memory Card
Q Batteries
Reemoving the Battery annd Memorry Caarrdd
• Remove dirt from the battery terminals with a clean,
dry cloth. Failure to observe this precaution could
prevent the battery from charging.
• Do not affix stickers or other objects to the battery.
Failure to observe this precaution could make it im-
possible to remove the battery from the camera.
• Do not short the battery terminals. The battery could
overheat.
• Read the cautions in “The Battery and Power Supply”
(Piv).
• Use only battery chargers designated for use with the
battery. Failure to observe this precaution could re-
sult in product malfunction.
Before removing the battery or memory card, turn
the camera off and open the battery-chamber cover.
To remove the battery, press
the battery latch to the side,
and slide the battery out of
Battery latch
the camera as shown.
To remove the memory card,
press it in and release it slowly.
The card can then be removed
by hand. When a memory card
is removed, the card could
come out of the slot too quickly. Use your finger to
hold it and gently release the card.
• Do not remove the labels from the battery or attempt
to split or peel the outer casing.
• The battery gradually loses its charge when not in
use. Charge the battery one or two days before use.
14
Inserting the Battery and a Memory Card
• Do not affix labels to memory cards. Peeling labels
can cause camera malfunction.
• Movie recording may be interrupted with some types
of SD/SDHC/SDXC memory card. Use a Gcard
or better when shooting HD movies.
• The data in internal memory may be erased or cor-
rupted when the camera is repaired. Please note that
the repairer will be able to view pictures in internal
memory.
• Formatting a memory card or internal memory in the
camera creates a folder in which pictures are stored.
Do not rename or delete this folder or use a comput-
er or other device to edit, delete, or rename image
files. Always use the camera to delete pictures from
memory cards and internal memory; before editing
or renaming files, copy them to a computer and edit
or rename the copies, not the originals. Renaming
the files on the camera can cause problems during
playback.
■ Compatible Memory Cards
FUJIFILM and SanDisk SD, SDHC, and SDXC mem-
ory cards have been approved for use in the cam-
era. A complete list of approved memory cards
is available at http://www.fujifilm.com/support/
digital_cameras/compatibility/. Operation is not
guaranteed with other cards. The camera can not
be used with xD-Picture Cards or MultiMediaCard
(MMC) devices.
Q Memory Caarrds
• Do not turn the camera off or remove the memory
card while the memory card is being formatted or
data are being recorded to or deleted from the card.
Failure to observe this precaution could damage the
card.
• Format memory cards before first use, and be sure
to reformat all memory cards after using them in a
computer or other device. For more information on
formatting memory cards, see page 81.
• Memory cards are small and can be swallowed; keep
out of reach of children. If a child swallows a memory
card, seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller
than the standard dimensions of an SD/SDHC/SDXC
card may not eject normally; if the card does not
eject, take the camera to an authorized service repre-
sentative. Do not forcibly remove the card.
15
Turning the Camera on and Off
Rotate the ON/OFF switch to ON to turn the camera on. Select OFF to turn
the camera off.
R Press the a button to start playback. Press the shutter button halfway to
return to shooting mode.
R The camera will turn off automatically if no operations are performed for the
length of time selected for MAUTO POWER OFF (P83). To reactivate the camera after it has turned off auto-
matically, press the shutter button halfway or turn the ON/OFF switch to OFF and then back to ON.
R For information on other power saving and startup options, see page 23.
Q Fingerprints and other marks on the lens or viewfinder can affect pictures or the view through the viewfinder.
Keep the lens and viewfinder clean.
Batterryy LLevel
After turning the camera on, check the battery level in the display.
Indicator
D(white)
C(white)
B(red)
Description
Battery partially discharged.
Battery more than half discharged
Low battery. Charge as soon as possible.
A(blinks red)
Battery exhausted. Turn camera off and recharge battery.
16
Baassic SSetup
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as
described below (you can reset the clock or change languages at any time using the FDATE/TIME
or La options in the setup menu; for information on displaying the setup menu, see page 80).
Choose a language.
1
Highlight a language and press MENU/OK.
R Press DISP/BACK to skip the current step. Any steps you skip will be displayed
the next time the camera is turned on.
Set the date and time.
2
Press the command dial left or right to highlight the year, month, day,
hour, or minute and press up or down to change. To change the order
in which the year, month, and day are displayed, highlight the date
format and press the command dial up or down. Press MENU/OK to exit
to shooting mode when settings are complete.
R If the battery is removed for an extended period, the camera clock will be reset and the language-selection
dialog will be displayed when the camera is turned on.
17
Chhooosing a Display
The camera is equipped with a hybrid optical/electronic viewfinder
(OVF/EVF) and an LCD monitor (LCD). Press VIEW MODE to choose a dis-
play.
OVF/EVF
OVF/EVF
LCD
LCD
Automatic display selection
using eye sensor
Viewfinder only
LCD monitor only
Automatic Display Selection
Eye sensor
In this mode, the viewfinder turns on automatically when you put your eye to the view-
finder, and the LCD monitor turns on when you take your eye away (note that the eye sensor
may respond to objects other than your eye or to light shining directly on the sensor).
18
Choosing a Display
Using the Hybrid Viewfinder
Focusing the Viewfinder
Use the viewfinder selector to
choose between optical and
electronic viewfinders.
The camera is equipped with
diopter adjustment (–2–+1m–1
(dpt)) to accommodate individ-
ual differences in vision. Rotate
the diopter adjustment control
until the viewfinder display is in sharp focus.
Optical viewfinder display
Electronic viewfinder display
Choosing a Display
Choose a display according to the task.
Display
Description
This display is immune from digital video effects and allows the subject to be viewed directly with no display
lag. Subjects are always in focus, allowing you to check their expression at any time, while a field of view
Optical
viewfinder slightly larger than that of the lens makes it easier to locate your subject without removing your eye from
(OVF)
the viewfinder. The viewfinder window is however at a slight distance from the lens, with the result that the
display in the viewfinder may differ slightly from the final photograph due to parallax.
Electronic This display shows the view through the lens and has exactly the same field of view, allowing you to frame
viewfinder your subjects precisely and preview focus, depth of field, exposure, and white balance (although there may
(EVF)
be a slight display lag). It can also be used to view photographs after shooting.
This display is identical to the electronic viewfinder, except that its large size makes it easier to view shooting
indicators and the view through the lens. It may however be difficult to see in bright light.
LCD monitor
19
The DISP/BACK Button
The DISP/BACK button controls the display of indicators in the viewfinder and LCD monitor.
■ Optical Viewfinder: Shooting
■ LCD Monitor: Shooting
100
Detailed display
Standard display
Standard display
Custom display
■ Electronic Viewfinder: Shooting
Custom display
Standard display
Custom display
Custom DDisplay
Choose items for display using vDISP. CUSTOM SETTING in the shooting menu (P72):
Framing grid
Exposure compensation/exposure indicator
Dynamic range
Virtual horizon
Autofocus distance
Histogram
Metering
Number of exposures remaining/media
Image quality and size
Battery level
Flash mode
White balance
Film simulation
Exposure (shutter speed, aperture, and sensitivity)
R See pages6–7 for the locations of these items in the displays.
20
The DISP/BACK Buttion
■ Electronic Viewfinder/LCD Monitor: Playback
Indicators displayed
Indicators hidden
Favorites
Photo information
AM
3
Q The optical viewfinder can not be used for playback.
Histoograms
Histograms show the distribution of tones in the im- Optimal exposure: Pixels are distrib-
age. Brightness is shown by the horizontal axis, the uted in an even curve through-
number of pixels by the vertical axis.
out the tone range.
Overexposed: Pixels are clustered
Shadows
Highlights
on the right side of the graph.
No. of pixels
Underexposed: Pixels are clustered
on the left side of the graph.
Pixel brightness
21
Chhoosiinngg aa SShutteerr SSound
Use the eSHUTTER SOUND item in the setup menu to choose the sound made by the shutter.
Press MENU/OK to display the menus.
Highlight eSHUTTER SOUND
and press the command dial right.
1
4
Press the command dial left to se-
lect the tab for the current menu.
2
Tab
Highlight one of the following op-
tions and press MENU/OK.
• i: A leaf shutter sound.
• j: A focal plane shutter sound.
• k: A mirror reflex sound.
5
6
Highlight the setup menu tab (X)
and press the command dial right to
place the cursor in the setup menu.
3
Press DISP/BACK to return to shooting
mode.
Silennt Mode
In situations in which camera sounds or lights may be unwelcome, press the
DISP/BACK button for a second, or select ON for oSILENT MODE in the setup
menu (P80; note that silent mode is not available during movie playback). The
camera speaker, flash, and AF-assist illuminator/self-timer lamp turn off and
flash and volume settings can not be adjusted.
22
Power Mannagement
The setup menu contains the following power management options. For information on using the
setup menu, see the previous page.
GOVF POWER SAVE MODE
HQUICK START MODE
Selecting ON for GOVF POWER SAVE MODE To reduce camera startup time, select ON for
approximately doubles the number of photo- HQUICK START MODE.
graphs that can be taken with a fully-charged
battery.
R ON reduces startup time to about 0.7 seconds, com-
pared to about 2.2 seconds when OFF is selected.
R Selecting ON increases the time required for auto-
Q The camera will need 2.2 seconds to start up if it is
left off for more than about 20 minutes.
Q The camera requires slightly longer to start up when
a short focus distance is selected for manual focus.
Q Selecting ON increases the drain on the battery, re-
focus to about 0.4 seconds, compared to about 0.2
seconds when OFF is selected (the time required to
focus varies with the subject).
R When power saving is in effect, shooting informa-
tion is not displayed until the shutter button is
pressed halfway.
a single charge.
ducing the number of pictures that can be taken on
Q Power saving is available only when the optical
viewfinder is used.
23
Taking Photographs
Proggrraamm AAEE ((PP)
To allow the camera to adjust both shutter speed and aperture
for optimal exposure, rotate the aperture ring and shutter speed
dial to A. P will appear in the display.
Q If the subject is outside the metering range of the camera, the shutter
speed and aperture displays will show“–––”.
Optical viewfinder
EVF/LCD
Prooggrraamm SShhiifft
If desired, you can rotate the command dial or press the command con-
trol left or right to other combinations of shutter speed and aperture
without altering exposure (program shift). Program shift is not avail-
able when a flash is used, AUTO is selected for UDYNAMIC RANGE
in the shooting menu (P70), or ON is selected for NISO AUTO CON-
TROL in the setup menu (P84).
Shutter speed
Aperture
24
Shhuutttteerr--PPrriioorriitty AE (S)
To adjust shutter speed manually while letting the camera select
aperture for optimal exposure, rotate the aperture ring to A and
use the shutter speed dial. S will appear in the display.
Q If the correct exposure can not be achieved at the selected shutter
speed, aperture will be displayed in red when the shutter button is
pressed halfway. Adjust shutter speed until the correct exposure is
achieved.
Q If the subject is outside the metering range of the camera, the aper-
ture display will show“–––”.
Optical viewfinder
EVF/LCD
/
R Shutter speed can also be adjusted in increments of 1 3EV by rotating
the command dial.
Command dial
25
Aperture--PPrriioorriitty AE (A)
To adjust aperture manually while letting the camera select shut-
ter speed for optimal exposure, rotate the shutter speed dial to A
and use the aperture ring. A will appear in the display.
Q If the correct exposure can not be achieved at the selected aper-
ture, the shutter speed will be displayed in red when the shutter but-
ton is pressed halfway. Adjust aperture until the correct exposure is
achieved.
Q If the subject is outside the metering range of the camera, the shutter
speed display will show“–––”.
Q The slowest shutter speed available when ON is selected for GOVF
Optical viewfinder
EVF/LCD
/
POWER SAVE MODE is 1 4s (P23).
/
R Aperture can also be adjusted in increments of 1 3EV by pressing the
command control left or right.
Command control
Depth of Field
The aperture ring can be used to adjust aperture before recording begins. Choose
a low f-numbers to soften background details. The effect can be heightened by
increasing the distance between your subject and the background.
Preevviieewwing Depth of Field
When LPREVIEW DEPTH OF FIELD is selected for FFn BUTTON (P53) in the set-up
menu, pressing the Fn button stops aperture down to the selected setting, allowing depth
of field to be previewed in the electronic viewfinder or LCD monitor.
26
Maannual Exppoossuurre (M)
Exposure can be altered from the value suggested by the camera
by rotating both the shutter speed dial and aperture ring to set-
tings other than A. M will appear in the display.
R The command dial and command control can be used to adjust
/
shutter speed and aperture by 2 3EV from the selected value in steps
/
of 1 3EV. Use the command dial to adjust shutter speed, the com-
mand control to adjust aperture.
Optical viewfinder
EVF/LCD
Command dial
Command control
R The manual exposure display includes an exposure indicator that
shows the amount the picture would be under- or over-exposed at
current settings.
27
Shhuutttteerr SSppeeeedd aand Aperture
Because the camera uses a lens-internal shutter, fast shutter speeds may not be available at large
apertures. If the selected combination of shutter speed and aperture is unavailable, shutter speed or
aperture will be displayed in red and the desired exposure may not be achieved.
Shutter speed
/
/
/
Aperture
F2
F2.8
F4
F5.6
14000s
12000s
11000s or slower
Not available
Available
Not available
Available
Available
F8 or aboove
28
Long Time-Exposuures (T/B)
Select a shutter speed of T (time) or B (bulb) for long time-exposures.
R Use of a tripod is recommended to prevent the camera from moving during the exposure.
R To reduce “noise” (mottling) in long time-exposures, select ON for KLONG EXPOSURE NR in the set-up
menu. Note that this may increase the time needed to record images after shooting.
Time (T)
Bulb (B)
Rotate the shutter speed dial to T.
Rotate the shutter speed dial to B.
1
1
Rotate the command dial to choose
a shutter speed between 1/2s and
30s in steps of 1/3EV.
Press the shutter button all the way
down. The shutter will remain open
for up to 60 minutes while the shut-
ter button is pressed.
2
2
R Rotating the aperture ring to A fixes shutter speed
at 30s.
Using a Remote Release
A remote release (available from third-party suppli-
ers) can be used for long time-exposures.
Press the shutter button all the way
down to take a picture at the select-
ed shutter speed.
3
29
Exposuure Compeensaation
Rotate the exposure compensation dial to adjust exposure when photographing very bright,
very dark, or high-contrast subjects. The effect is visible in the LCD monitor and electronic
viewfinder; when using the optical viewfinder, use the exposure indicator to check exposure.
Exposure compensation indicator
Choosing aan Expossuurre Coommppeennssaattiioonn VVaalue
• Backlit subjects: Choose values
/
/
from +2 3EV to +12 3EV (for an
explanation of the term “EV”,
see the Glossary on page 113).
OVF
EVF
LCD
• Highly reflective subjects or very
bright scenes (e.g., snowfields): +1EV
Choose positive values (+) to
increase exposure
• Scenes that are mostly sky: +1EV
• Spotlit subjects (particularly if photographed against dark back-
/
grounds): –2 3EV
• Subjects with low reflectivity (pine trees or dark-colored foliage):
/
Choose negative values (–) to
reduce exposure
–2 3EV
30
Focusing and Taking Pictures
Press the shutter button halfway to focus and the rest of the way down to shoot.
Focus.
1
Frame the picture with your subject in the center focus area and press the shutter button
halfway to focus.
R If the subject is poorly lit, the AF-assist illuminator may light (P85).
If the camera is able to focus, it will beep twice and focus area will glow green. Focus and exposure will
lock while the shutter button is pressed halfway.
If the camera is unable to focus, the focus frame will turn red, and swill be displayed.
Shoot.
2
Smoothly press the shutter button the rest of the way down to take the picture.
31
More on Photography
NUsing the Flashh ((SSuupper-Intelliigent Flash)
When the flash is used, the camera’s Super-Intelligent Flash system instantly analyzes the scene based
on such factors as the brightness of the subject, its position in the frame, and its distance from the
camera. Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed
while preserving the effects of ambient background lighting, even in dimly-lit indoor scenes. Use the
flash when lighting is poor, for example when shooting at night or indoors under low light.
To choose a flash mode, press the command dial right (N) to display the following
options, then rotate the dial or press it left or right to highlight an option and press
MENU/OK to select.
Mode
Description
AUTO (AUTO FLASH)/
The flash fires when required. Recommended in most situations.
K(RED EYE REDUCTION)*
N(FORCED FLASH)/
The flash fires whenever a picture is taken. Use for backlit subjects or for natural
L(FORCED FLASH)* coloration when shooting in bright light.
The flash does not fire even when the subject is poorly lit. Use of a tripod is recom-
mended.
P(SUPPRESSED FLASH)
O(SLOW SYNCHRO)/ Capture both the main subject and the background under low light (note that
M(RED-EYE & SLOW)* brightly lit scenes may be overexposed).
* Red-eye removal (K, L, or M) is available in these modes when ON is selected for BRED
EYEREMOVALinthesetupmenu(P84). Red-eyeremovalminimizes“red-eye”causedwhen
light from the flash is reflected from the subject’s retinas as shown in the illustration at right.
32
NUsing the Flash (Super-Intelligent Flash)
R If pis displayed when the shutter button is pressed halfway, the flash will fire when the photo is taken.
R The flash may fire several times with each shot. Do not move the camera until shooting is complete.
R Remove lens hoods to prevent shadows in photos taken with the flash.
Q Flash is not fired in silent mode.
Aperturree,, SSeennssitivity, annd Flash Range
Flash range varies with sensitivity and aperture.
Aperturee aatt sseennssiittiivviitty of
Range
200
—
—
—
—
—
2
2.8
4
5.6
8
400
—
—
—
—
2
2.8
4
5.6
8
800
—
—
—
2
2.8
4
5.6
8
1600
—
—
2
2.8
4
5.6
8
11
16
—
3200
—
2
2.8
4
5.6
8
11
16
—
—
6400
2
2.8
4
5.6
8
11
16
—
—
—
m
ft.
0.5–18
0.5–13
0.5–9.0
0.5–6.4
0.5–4.5
0.5–3.2
0.5–2.3
0.5–1.6
0.5–1.1
0.5–0.8
1.6–59
1.6–42
1.6–29
1.6–20
1.6–14
1.6–10
1.6–7.5
1.6–5.2
1.6–3.6
1.6–2.6
11
16
11
Fllash Sync Speed
/
The flash will synchronize with the shutter at a shutter speed of 1 2,000s.
Optionall Flash Units
The camera can be used with optional EF-20 and EF-42 flash units.
33
FMaacroo Mooddee ((CClloossee--uuppss))
To focus at distances as close as 10cm/4in., press the command dial left (F) and
select F. If the optical viewfinder is on, the camera will automatically switch to the
electronic viewfinder (because of parallax, the camera will not focus at distances
of less than 80cm/2.6ft. when the optical viewfinder is used). To exit macro mode,
press the command dial left and select OFF.
R The LCD monitor and electronic viewfinder can be used to focus at short ranges when macro mode is not
selected, but the time needed to focus increases.
R The shadow cast by the lens may appear in photographs taken with the flash at distances under 50cm/19.6in.
Turn the flash off or increase the distance to the subject.
34
Whitee BBalance
For natural colors, press the command dial down (WB) to display the following op-
tions, then rotate the dial or press it up or down to highlight an option that matches
the light source and press MENU/OK to select (for an explanation of “white balance,”
see the Glossary on page 113).
Option
Description
Option
k
Description
AUTO White balance adjusted automatically.
h
Use under“daylight”fluorescent lights.
Use under“warm white”fluorescent lights.
Use under“cool white”fluorescent lights.
Use under incandescent lighting.
Reduces the blue cast typically associated
with underwater lighting.
Measure a value for white balance (P36).
l
Selecting this option displays a list of color
temperatures (P36); highlight a tempera-
ture and press MENU/OK.
For subjects in direct sunlight.
For subjects in the shade.
m
k
n
g
i
j
R White balance is adjusted for flash lighting only in AUTO and gmodes. Turn the flash off using other white
balance options.
R Results vary with shooting conditions. Play pictures back after shooting to check colors.
35
White Balance
h: Custom White Balance
Choose hto adjust white balance for unusual lighting conditions. White balance measurement options will
be displayed; frame a white object so that it fills the display and press the shutter button all the way down to
measure white balance.
• If “COMPLETED!” is displayed, press MENU/OK to set white balance to the measured value.
• If “UNDER” is displayed, raise exposure compensation (P30) and try again.
• If “OVER” is displayed, lower exposure compensation and try again.
k: Coolloor Temperature
Color temperature is an objective measure of the color of a light source, expressed in Kelvin (K). Light sources
with a color temperature close to that of direct sunlight appear white; light sources with a lower color tempera-
ture have a yellow or red cast, while those with a higher color temperature are tinged with blue. You can match
color temperature to the light source as shown in the following table, or choose options that differ sharply from
the color of the light source to make pictures“warmer”or“colder.”
Choose for redder light sources
or “colder” pictures
Choose for bluer light sources
or “warmer” pictures
2,000 K
Candlelight
Sunset/sunrise
5,000 K
Direct sunlight
15,000 K
Blue sky
Shade
36
IContinuous Shhoooottiinngg ((BBuurrsstt MMoode)
Capture motion in a series of pictures.
Press the command dial up (DRIVE)
to display drive options, then rotate
the dial or press it up or down to
highlight I(TOP (RAW)). The options shown
below will be displayed.
Press the shutter button the rest
of the way down to start shooting.
Shooting ends when the shutter
button is released, after ten JPEG or
eight RAW pictures have been taken, or when
memory is full.
1
4
R Focus and exposure are determined by the first
frame in each series. The flash turns off automati-
cally; the previously-selected flash mode is restored
when burst shooting is turned off .
R Frame rate varies with shutter speed.
Press the command dial left or right to high-
2
3
R Additional time may be required to record pictures
when shooting ends; to cancel recording and take
next pictures immediately, press DISP/BACK.
R If file numbering reaches 999 before shooting is
complete, the remaining pictures will be recorded
to a new folder (P82).
light an option and press MENU/OK to select.
Option
Description
/
At shutter speeds faster than 1 100s, the camera
5 fps
takes pictures at 5 frames per second (fps).
/
At shutter speeds faster than 1 10s, the camera will
take pictures at 3fps.
3 fps
Press the shutter button halfway to
focus.
37
Bracketing
Automatically vary settings over a series of pictures.
Press the command dial up (DRIVE) to display drive options and rotate the dial or
1
press it up or down to highlight one of the following:
Option
Description
Press the command dial left or right to highlight a bracketing amount. Each time the
shutter button is pressed, the camera will take three shots at up to about 5fps: one us-
AE BKT ing the metered value for exposure, the second overexposed by the selected amount,
and the third underexposed by the same amount (regardless of the amount selected,
exposure will not exceed the limits of the exposure metering system).
Press the command dial left or right to highlight a bracketing amount. Each time the
shutter is released, the camera will take a picture at the current sensitivity (P51) and
ISO BKT process it to create two additional copies, one with sensitivity raised and the other with
sensitivity lowered by the selected amount (regardless of the amount selected, sensitiv-
ity will not exceed ISO 6400 or fall below ISO 200).
FILM
Each time the shutter is released, the camera takes one shot and processes it to create
SIMULATION three copies with different film simulation settings (P54): cPROVIA/STANDARD for
BKT
the first, dVelvia/VIVID for the second, and eASTIA/SOFT for the third.
Each time the shutter button is pressed, the camera takes three shots with different
dynamic ranges (P70): 100% for the first, 200% for the second, and 400% for the third.
The shots are taken at rates of up to about 5fps. While dynamic range bracketing is in
effect, sensitivity will be restricted to a minimum of ISO 800; the sensitivity previously in
effect is restored when bracketing ends.
DYNAMIC
RANGE BKT
Press MENU/OK to select the highlighted option.
Take photographs.
2
38
Panoramas
Follow an on-screen guide to create a panorama.
Press the command dial up (DRIVE)
to display drive options. Rotate the
dial or press it up or down to high-
light r (MOTION PANORAMA) and press
MENU/OK.
Press the command dial right to
view a choice of pan directions.
Press the dial it left or right to high-
light a pan direction and press MENU/OK.
1
3
4
FROM LEFT TO RIGHT
Press the shutter button all the way
down to start recording. There is
no need to keep the shutter button
pressed during recording.
To select the angle through which
you will pan the camera while
shooting, press the command dial
left. Press the dial left or right to highlight an
angle and press MENU/OK.
2
MOTION PANORAMA
39
Panoramas
Q Panoramas are created from multiple frames; expo-
sure for the entire panorama is determined by the
first frame. The camera may in some cases record an
greater or lesser angle than selected or be unable to
stitch the frames together perfectly. The last part of
the panorama may not be recorded if shooting ends
before the panorama is complete.
Pan the camera in the direction shown by the
5
arrow. Shooting ends automatically when the
camera is panned to the end of the guides
and the panorama is complete.
Q Shooting may be interrupted if the camera is panned
too quickly or too slowly. Panning the camera in a
direction other than that shown cancels shooting.
Q The desired results may not be achieved with mov-
ing subjects, subjects close to the camera, unvary-
ing subjects such as the sky or a field of grass, sub-
jects that are in constant motion, such as waves and
waterfalls, or subjects that undergo marked chang-
es in brightness. Panoramas may be blurred if the
subject is poorly lit.
AN
DIEIN
R Shooting ends if the shutter button is pressed all
the way down during shooting. No panorama
will be recorded if the shutter button is pressed
before the camera has been panned through
120°.
40
Panoramas
The size of the completed panorama varies with
the angle and pan direction.
For Besst Results
For best results, prop your elbows against your sides
and move the camera slowly in a small circle at a
steady speed, keeping the camera horizontal and
being careful only to pan in the direction shown by
the guides. Use a tripod for best results. If the desired
results are not achieved, try panning at a different
speed.
Angle
Pan diirection
Horizontal
Vertical
Size (W × H)
5,120×1,,440/ 7.3M
2,160×5,120/11.1M
7,680×1,440/11.1M
2,160×7,680/16.6M
120°
Horizontal
Vertical
180°
41
FRecording High-Definition (HDD)) MMovies
Record short high-definition (1,280×720) movies at a frame rate of 24fps. Sound is recorded in stereo
via the built-in microphone; during recording, do not cover the microphone or use the viewfinder se-
lector, which is located next to the microphone.
R Focus, exposure, and white balance are adjusted
automatically throughout recording. The color and
brightness of the image may vary from those dis-
played before recording begins.
R The indicator lamp lights while movies are being
recorded.
Press the command dial up (DRIVE)
to display drive options. Rotate the
dial or press it up or down to high-
light F(MOVIE) and press MENU/OK.
1
Q The microphone may pick up lens noise and other
sounds made by the camera during recording.
Q Vertical or horizontal streaks may appear in movies
containing very bright subjects. This is normal and
does not indicate a malfunction.
MOVE
Q If the optical viewfinder is on, the camera will au-
tomatically switch to the electronic viewfinder.
Press the shutter button all the way
down to start recording.
2
3
Press the shutter button all the way
down again to end recording. Re-
cording ends automatically after ten
minutes or when memory is full.
42
FRecording High-Definition (HD) Movies
Before Recording
Before recording, adjust aperture (P26), white balance (P35), film simulation (P54), and exposure
compensation (P30) and select a focus mode (P48).
R To increase zoom by 3× for a focal length equivalent to 105mm (35mm format), press the kbutton before
recording begins. Press nto cancel zoom.
Q Continuous AF is used when AF-S is selected for focus mode.
Q Aperture control and manual focus are not available during recording.
43
hUsing thee Selff-Timer
Use the timer for self-portraits or to prevent blur caused by camera shake.
Press MENU/OK in shooting mode to display the shooting menu. Press
the command dial up or down to highlight BSELF-TIMER and
press MENU/OK.
1
Press the command dial up or down to highlight one of the following
2
options and press MENU/OK to select.
Option
Description
The shutter is released ten seconds after the shutter button is pressed. Use
for photographs in which you wish to appear yourself.
S10 SEC
The shutter is released two seconds after the shutter button is pressed. Use
R2 SEC to reduce blur caused by the camera moving when the shutter button is
pressed.
OFF
Self-timer off.
Press the shutter button halfway to focus.
3
Q Stand behind the camera when using the shutter button. Standing in
front of the lens can interfere with focus and exposure.
44
hUsing the Self-Timer
Press the shutter button the rest of the way down to start the timer.
The display in the monitor shows the number of seconds remaining
until the shutter is released. To stop the timer before the picture is
taken, press DISP/BACK.
4
The self-timer lamp on the front of the camera will blink immediately
before the picture is taken. If the two-second timer is selected, the
self-timer lamp will blink as the timer counts down.
R The self-timer turns off automatically when the camera is turned off.
45
Focus/Expossure Lock
To compose photographs with off-center subjects:
Focus: Position the subject in the focus frame and press the shutter button half-
way to lock focus and exposure. Focus and exposure will remain locked while
the shutter button is pressed halfway (AF/AE lock).
1
R Depending on the option selected for vAE/AF-LOCK BUTTON in the setup menu (P85), focus and/or
exposure can also be locked by pressing the AFL/AEL button; focus and/or exposure will remain locked even
if the shutter button is pressed. Choose AE LOCK ONLY to lock exposure but not focus, AF LOCK ONLY to
lock focus but not exposure, or AE/AF LOCK to lock both focus and exposure. In manual focus mode (P48),
the camera will focus automatically with the AFL/AEL button.
Recompose: Keep the shutter button pressed halfway or keep the AFL/AEL button
pressed.
2
3
R If AE&AF ON/OFF SWITCH is selected for kAE/AF-LOCK MODE (P85), focus and/or
exposure lock when the AFL/AEL button is pressed and remain locked until the button
is pressed again.
Shoot: Press the button all the way down.
46
Focus/Exposure Lock
Autoffocus
Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed
below.
• Very shiny subjects such as mirrors or car bodies.
• Fast-moving subjects.
• Subjects photographed through a window or other reflective object.
• Dark subjects and subjects that absorb rather than reflect light, such as hair or fur.
• Insubstantial subjects, such as smoke or flame.
• Subjects that show little contrast with the background (for example, subjects in clothing that is the same color
as the background).
• Subjects positioned in front of or behind a high-contrast object that is also in the focus frame (for example, a
subject photographed against a backdrop of highly contrasting elements).
47
Focus MMode
Use the focus mode selector to choose how the camera focuses.
• AF-S (Single AF): Focus locks while the shutter button is pressed halfway. Choose for
stationary subjects.
• AF-C (Continuous AF): Focus is continually adjusted to reflect changes in the distance to
the subject even when the shutter button is not pressed halfway (note that this increases the drain
on the battery).
• MF (Manual): Focus manually using the focus ring. Rotate the ring left to reduce the focus distance, right
to increase. The manual focus indicator indicates how closely the focus distance matches the dis-
tance to the subject in the focus brackets (the red bar indicates the focus distance, the white bar the
depth of field, or in other words the distance in front of and behind the focus point that appears to
be in focus); you can also check focus visually in the electronic viewfinder or LCD monitor. Choose for
manual control of focus or in situations in which the camera is unable to focus using autofocus (P47).
Focus distance
(red bar)
Manual focus
mode icon
.
Reduce focus
distance
Increase focus
distance
Manual focus
indicator
Depth of field
(white bar)
R Use the IFOCUS RING option in the setup menu (P85) to reverse the direction of rotation of the focus ring.
R The camera will not focus if the focus ring is rotated past infinity.
R To focus using autofocus, press the AFL/AEL button. This can be used to quickly focus on a chosen subject in
manual focus mode.
R The camera can show focus distance in meters or feet. Use the MFOCUS SCALE UNITS option in the setup
menu (P85) to choose the units used.
48
Focus Mode
Maannuall Focuss
If ON is selected for jFOCUS CHECK in the setup menu (P85),
pressing the center of the command control magnifies the view in
the electronic viewfinder or LCD monitor for precise focus. To scroll
to other areas of the frame, press the AF button and rotate the com-
mand dial.
49
Focus Frame Selection
When tAREA is selected for FAF MODE in the shooting
menu and AF-S is selected for focus mode, the electronic view-
finder and LCD monitor offer a choice of 49 focus points and the
optical viewfinder a choice of 25, allowing photographs to be
composed with the main subject positioned almost anywhere in
the frame. To position the focus frame, press the AF button and
use the command dial (the focus frame can be returned to the
center by pressing MENU/OK).
+
Focus point
Focus frame
EVF/LCD
Q When you switch to the optical viewfinder, the camera will select the
focus frame closest to that selected in the electronic viewfinder or
LCD monitor.
OVF
When framing pictures in the electronic viewfinder or LCD moni-
tor, you can choose the size of the focus frame for AF-S by press-
ing the AF button and pressing the command control left or
right. Press the control left to reduce the frame by up to 50%,
right to enlarge it by up to 150%. The setting takes effect when
you release the AF button.
+
EVF/LCD
50
Sensitiivviitty
“Sensitivity” refers to the camera’s sensitivity to light. Choose from values between L (100) (ISO 100)
and H (12800) (ISO 12800). Higher values can be used to reduce blur when lighting is poor, while low-
er values allow slower shutter speeds or wider apertures in bright light; note, however, that mottling
may appear in pictures taken at high sensitivities, particularly at H (12800), while choosing L (100)
reduces dynamic range. Values of from ISO 200 to ISO 6400 are recommended in most situations.
Press MENU/OK in shooting mode to display the shooting menu. Press
the command dial up or down to highlight NISO and press MENU/
OK.
1
R At default settings, ISO options can also be displayed by pressing the Fn
button.
Press the command dial up or down to highlight the desired option
and press MENU/OK to select.
2
R Sensitivity is not reset when the camera is turned off.
R Sensitivities of L (100) and H (12800) are respectively reset to ISO 200 and 6400 when RAW, FINE+RAW,
or NORMAL+RAW is selected for image quality (P56, 70). For more information on the settings available with
L (100) and H (12800), see page 120.
R If ON is selected for NISO AUTO CONTROL in the setup menu (P84), the camera will automatically adjust
sensitivity if optimal exposure can not be achieved at current settings. The currently selected value is shown
until the shutter button is pressed halfway, when the camera shows the adjusted value.
51
Meettering
To choose how the camera meters exposure, press the AE button
and rotate the command dial (you can also select the metering
method by pressing the AE button and pressing the command
control left or right). The following options are available:
+
Mode
Description
The camera instantly determines exposure based on an analysis of
composition, color, and brightness distribution. Recommended in
most situations.
The camera meters lighting conditions in an area at the center of the
frame equivalent to 2% of the total. Recommended when the back-
ground is much brighter or darker than the main subject; due to paral-
lax, not recommended when pictures are framed in the optical view-
finder.
o
(MULTI)
MULTI
OVF
EVF/LCD
p
(SPOT)
Exposure is set to the average for the entire frame. Provides consistent
exposure across multiple shots with the same lighting, and is particu-
q
(AVERAGE) larly effective for landscapes and portraits of subjects dressed in black
or white.
The setting takes effect when you release the AE button.
52
The Fn BBuutttton
The role played by the Fn button can be selected using the FFn
BUTTON option in the setup menu (P83).The options available include
depth-of-field preview (P26), the self-timer (P44), sensitivity (P51),
image size (P69), image quality (P70), dynamic range (P70), film
simulation (P54), ND filter (P57), AF mode (P71), movie recording
(P42), and custom settings (P55).
R The FFn BUTTON menu can also be displayed by pressing and holding the Fn button.
53
Film Simulation
Simulate the effects of different kinds of film, including black-and-white (with or without color filters).
Press MENU/OK in shooting mode to display the shooting menu. Press
the command dial up or down to highlight PFILM SIMULATION
and press MENU/OK.
1
Press the command dial up or down to highlight one of the following options and press MENU/OK
2
to select.
Option
c(PROVIA/STANDARD)
=(Velvia/VIVD)
Description
Standard color reproduction. Suited to a wide range of subjects, from portraits to landscapes.
A high-contrast palette of saturated colors, suited to nature photos.
A soft-toned palette of less saturated colors.
>(ASTIA/SOFT)
;(MONOCHROME)
Take pictures in standard black and white.
Take black-and-white pictures with slightly increased contrast. This setting also slightly tones
down the brightness of the sky.
e (MONOCHROME + Ye FILTER)
Take black-and-white pictures with increased contrast. This setting also tones down the bright-
ness of the sky.
d (MONOCHROME + R FILTER)
f (MONOCHROME + G FILTER) Soften skin tones in black-and-white portraits
f(SEPIA)
Take pictures in sepia.
R Film simulation options can be combined with tone and sharpness settings (P71).
54
Saving Settings
Save up to three sets of custom camera settings for commonly-encountered situations. Saved settings
can be recalled using the uSELECT CUSTOM SETTING option in the shooting menu.
Press MENU/OK in shooting mode to display the shooting menu. Press
the command dial up or down to highlight KEDIT/SAVE CUSTOM
SETTING and press MENU/OK.
1
Highlight a custom settings bank and press MENU/OK to select. Adjust
the following as desired and press DISP/BACK when adjustments are
complete: NISO, UDYNAMIC RANGE, PFILM SIMULATION,
DWHITE BALANCE, fCOLOR, rHIGHLIGHT TONE, sSHADOW
TONE, HSHARPNESS, and hNOISE REDUCTION.
2
R To replace the settings in the selected bank with the settings currently selected with the camera, select
KSAVE CURRENT SETTINGS and press MENU/OK.
A confirmation dialog will be displayed; highlight OK and press MENU/
OK.
3
55
The RAWW BBuutttton
Press the RAW button toggle RAW image quality on or off for a single
shot. If a JPEG option is currently selected for image quality, pressing
the RAW button temporarily selects the equivalent JPEG+RAW option.
If a JPEG+RAW option is currently selected, pressing the RAW button
temporarily selects the equivalent JPEG option, while if RAW is selected,
pressing the RAW button temporarily selects FINE. Taking a picture or pressing the RAW button again
restores the previous setting.
R RAW images record raw, unprocessed data from the camera image sensor. JPEG copies of RAW images can
be created using the jRAW CONVERSION option in the playback menu, or RAW images can be viewed on
a computer using the RAW File Converter application that is installed with the software on the supplied CD
(P94, 96).
R Sensitivities of L (100) and H (12800) are not available when RAW image quality is on (P51).
R Control lock (P4) disables the RAW button. To enable the RAW button, press MENU/OK until the X icon clears
from the display.
56
The ND FFiilltter
The camera is equipped with a Neutral Density (ND) filter that reduces exposure by the equivalent of
3EV. This allows slower shutter speeds or wider apertures to be used with brightly lit subjects, making
it possible to blur motion or soften background details without risk of overexposure.
Press MENU/OK in shooting mode to display the shooting menu. Press
the command dial up or down to highlight tND FILTER and press
MENU/OK.
1
2
Press the command dial up or down to highlight ON and press MENU/OK to select.
57
Viewing Pictures
Viewing Pictures Full Frame
Pictures can be viewed in the electronic viewfinder or LCD monitor. When taking important pictures,
take a test shot and check the results.
To view pictures full frame, press a.
Deletingg Piccttuurres
To delete the current picture, press the
command dial up (b). The following dia-
log will be displayed.
3
Additional pictures can be viewed by
pressing the command dial left or right.
Press the dial right to view pictures in
the order recorded, left to view pictures in reverse
order. Keep the command dial pressed to scroll
rapidly to the desired frame.
To delete the picture, highlight OK and
press MENU/OK. To exit without deleting
the picture, highlight CANCEL and press
MENU/OK.
R Pictures taken using other cameras are indicated by
R Pictures can also be deleted from the playback
a m(“gift image”) icon during playback.
menu (P67).
Favorittes: Rattinngg PPiiccttuurres
Creatingg JPEEGG CCopies of RAW PPicttuurres
Pressing the RAW button during playback displays
RAW conversion options (P68).
To rate the current picture, press DISP/BACK and press
the command dial up and down to select from zero
to five stars.
58
Viewing Pictures Full Frame
Playback Zoom
Photo Infformaation
Press kto zoom in on the current picture, nto
zoom out. When the picture is zoomed in, the
command dial can be used to view areas of the
image not currently visible in the display. Press
DISP/BACK or MENU/OK to exit zoom.
Photo information can be viewed
by pressing the command con-
trol right.
Zoom indicator
Press the control left or right to view additional in-
formation.
Navigation window
shows portion of image
currently displayed
R The active focus point is shown by a“+”icon.
R The maximum zoom ratio varies with image size
(P69). Playback zoom is not available with cropped
or resized copies saved at a size of a.
Zoooommiinngg iinn oonn tthe Focus Point
Press the center of the com-
mand control to zoom in on the
focus point. Press the center of
the command control again to
return to full-frame playback.
59
Viewing Pictures Full Frame
Multi-Frame Playback
To change the number of images displayed, press nwhen a picture is displayed full frame.
Press nto view
more images.
Press kto view
fewer images.
Use the command dial to highlight images and press MENU/OK to view the highlighted image full frame.
In the nine- and hundred-frame displays, press the command dial up or down to view more pictures.
60
Viewingg Movvies
Movie icon
During playback, movies are displayed as shown at right. The following operations
can be performed while a movie is displayed:
Operation
Description
Press the command dial down to start playback. Press again to pause. While playback
Start/pause playback is paused, you can press the selector left or right to rewind or advance one frame
at a time.
End playback
Press the command dial up to end playback.
Press the command dial left or right to adjust playback speed during playback. Speed
is shown by the number of arrows (M or N).
Adjust speed
Press MENU/OK to pause playback and display volume controls. Press the command
dial up or down to adjust the volume; press MENU/OK again to resume playback.
Adjust volume
Progress bar
Progress is shown in the display during playback.
Q Do not cover the speaker during playback.
Q Sound is not played back in silent mode.
61
Immaage SSearch
Follow the steps below to search for pictures.
Press MENU/OK during playback to display the playback menu. Press the command dial up or down
to highlight bIMAGE SEARCH and press MENU/OK.
1
2
Highlight an option and press MENU/OK.
Option
BY DATE
BY FACE
Description
Search by date.
Search for pictures that include faces.
BY I FAVORITES Search by rating.
BY TYPE OF DATA Find all still pictures, all movies, all pictures taken in burst mode, or all RAW pictures.
BY UPLOAD MARK Find all pictures selected for upload to a specified destination.
Option
AERASE
DPROTECT
ISLIDE SHOW
See page
67
76
Select a search condition. Only pictures that match the search condition will
be displayed. To delete or protect selected pictures or to view the selected
pictures in a slide show, press MENU/OK and choose from the options at right.
3
4
75
To end the search, select EXIT SEARCH.
62
mPhotooBBoook Assist
Create books from your favorite photos.
Creating a PhotoBook
Select NEW BOOK for mPHOTOBOOK AS-
SIST in the playback menu (P73) and choose
from the following options:
• SELECT FROM ALL: Choose from all available
pictures.
Select COMPLETE PHOTOBOOK (to select all
photos or all photos matching the specified
search conditions for the book, choose SE-
LECT ALL). The new book will be added to
the list in the photobook assist menu.
1
3
• SELECT BY IMAGE SEARCH: Choose from pictures
matching selected search conditions (P62).
Q Books can contain up to 300 pictures.
Q Books that contain no photos are automatically de-
leted.
R Neither photographs a or smaller nor movies
can be selected for photobooks.
Scroll through the images and press the com-
mand dial up to select or deselect. To display
the current image on the cover, press the
command dial down. Press MENU/OK to exit
when the book is complete.
2
R The first picture selected becomes the cover im-
age. Press the command dial down to select a
different image for the cover.
63
mPhotoBook Assist
Viewing Photobooks
Editing and Deleting Photobooks
Highlight a book in the photobook assist menu Display the photobook and press MENU/OK. The
and press MENU/OK to display the book, then press following options will be displayed; select the
the command dial left or right to scroll through desired option and follow the on-screen instruc-
the pictures.
tions.
• EDIT: Edit the book as described in “Creating a
PhotoBook”(P63).
• ERASE: Delete the book.
Photoobooks
Photobooks can be copied to a computer using the supplied MyFinePix Studio software.
64
Viewing Panoramas
If you press the command dial down when a panorama is
displayed full frame, the camera will play back the picture
from left to right or from bottom to top. Press the command
dial down to pause and resume playback, or press the dial
up to return to full-frame playback. To rewind or advance
one frame at a time, press the command dial left or right while playback is paused.
65
Viewing Pictures Taken in a Single Burst
Position in burst/total number
of pictures in burst
When a picture taken in continuous shooting mode is dis-
played full frame, the first picture in the current burst can be
viewed by pressing the command dial down (burst mode
playback). Press the dial right to view pictures in the order
recorded, left to view pictures in reverse order. Keep the dial
pressed to scroll rapidly to the desired frame. To exit, press
DISP/BACK.
First picture in burst
R Pressing the command dial right when the last picture in the burst is displayed displays the first picture in the
burst; similarly, pressing the dial left when the first picture is displayed displays the last picture.
R Deletion (P58), rotation (P77), protect (P76), and copy (P78) operations applied during burst mode
playback apply only to the current picture. In contrast, if these operations are performed when a picture taken
in continuous shooting mode is displayed in single-frame playback, all images in the same burst will be af-
fected.
Bursts That Cross Folders
If a single burst is spread across multiple folders, the pictures in each folder will be treated as separate bursts.
Viewing Photo Information
To view photo information for a picture taken in continuous shooting mode, display it in burst mode playback.
Photo information for pictures taken in continuous shooting mode can not be viewed during single-frame
playback.
66
xDeleting Pictures
The AERASE option in the playback menu can be used to delete individual pictures, multiple select-
ed pictures, or all pictures. Note that deleted pictures can not be recovered. Copy important pictures to
a computer or other storage device before proceeding.
Press MENU/OK during playback to display the playback menu, then press the com-
mand dial up or down to highlight AERASE and press right to display the follow-
ing options. Press the dial up or down to highlight an option and press MENU/OK to
select.
Option
FRAME
Description
Press the command dial left or right through pictures and press MENU/OK to delete the current picture (a con-
firmation dialog is not displayed)
Highlight pictures and press MENU/OK to select or deselect (pictures that in a photobook or print order are
SELECTED FRAMES shown by S). When the operation is complete, press DISP/BACK to display a confirmation dialog, then high-
light OK and press MENU/OK.
A confirmation dialog will be displayed; highlight OK and press MENU/OK to delete all unprotected pictures.
Pressing DISP/BACK cancels deletion; note that any pictures deleted before the button was pressed can not be
ALL FRAMES
recovered.
R When a memory card is inserted, pictures will be deleted from the memory card; otherwise, pictures will be
deleted from internal memory.
R Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (P76).
R If a message appears stating that the selected images are part of a DPOF print order, press MENU/OK to delete
the pictures.
67
Crreeaattiing JPEG Copiess of RAAWW PPiiccttuurreess
RAW pictures store information on camera settings separately from the data captured by the camera
image sensor. Using the jRAW CONVERSION option in the playback menu, you can create JPEG
copies of RAW pictures using different options for the settings listed below. The original image data are
unaffected, allowing a single RAW image to be processed in a multitude of different ways.
Setting
REFLECT
Description
Press MENU/OK during playback to display the
playback menu, then press the command dial
up or down to highlight jRAW CONVER-
SION and press MENU/OK to display the set-
tings listed in the table at right.
1
Create a JPEG copy using the settings in ef-
SHOOTING COND. fect at the time the photo was taken.
PUSH/PULL
PROCESSING
Adjust exposure by –1EV to +3EV in incre-
ments of 1 3EV (P30).
Enhance details in highlights for natural con-
/
DYNAMIC RANGE
FILM SIMULATION
trast (P70).
Press the command dial up
or down to highlight a set-
2
Simulate the effects of different types of film
(P54).
ting and press the dial right
WHITE BALANCE Adjust white balance (P35).
WB SHIFT
COLOR
to select. Press the dial up
Fine-tune white balance (P70).
Adjust color density (P70).
Sharpen or soften outlines (P71).
or down to highlight the
SHARPNESS
desired option and press MENU/OK to select
and return to the settings list. Repeat this step
to adjust additional settings.
NOISE REDUCTION Process the copy to reduce mottling (P71).
HIGHLIGHT TONE Adjust highlights (P71).
SHADOW TONE
Adjust shadows (P71).
Press the RAW button to
preview the JPEG copy.
Press MENU/OK to save the
copy or press DISP/BACK to
Choose the color space used for color repro-
duction (P86).
3
COLOR SPACE
return to Step 2.
68
Menus
Using the MMenus: Shhoooottiinngg MMode
The shooting menu is used to adjust settings for a wide range of shooting condi-
tions. To display the shooting menu, press MENU/OK in shooting mode. Highlight
items and press the command dial right to view options, then highlight an option
and press MENU/OK. Press DISP/BACK to exit when settings are complete.
Shooting Menu Options
BSELF-TIMER
(defaults to OFF)
Take pictures with the self-timer (P44).
NISO
(defaults to 200)
Control the camera’s sensitivity to light (P51).
OIMAGE SIZE
(defaults to O3 : 2)
Choose the size and aspect ratio at which still pictures are recorded.
Option Prints at sizes up to
O3 : 2 36 × 24 cm (14 × 9.5 in.)
O16 : 9 36 × 20 cm (14 × 8 in.)
P3 : 2 26 × 17 cm (10 × 7 in.)
P16 : 9 26 × 15 cm (10 × 6 in.)
Q3 : 2 18 × 12 cm (7.5 × 5 in.)
Q16 : 9 17 × 9 cm (7 × 3.5 in.)
Aspect Ratio
Pictures with an aspect ratio of 3:2 have the same proportions as a frame ooff 3355mmmm fifillmm,, wwhhiillee
an aspect ratio of 16:9 is suited to display on High Definition (HD) deviices.
OIMAGE SIZE is not reset when the camera is turned off or another shooting mode is selected.
69
Using the Menus: Shooting Mode
TIMAGE QUALITY
(defaults to FINE)
Choose a file format and compression ratio. Select FINE or NORMAL to record JPEG images, RAW to record RAW images, or
FINE+RAW or NORMAL+RAW to record both JPEG and RAW images. FINE and FINE+RAW use lower JPEG compression ratios
for higher-quality JPEG images, while NORMAL and NORMAL+RAW user higher JPEG compression ratios to increase the num-
ber of images that can be stored.
UDYNAMIC RANGE
(defaults to A)
Control contrast. Choose lower values to increase contrast when shooting indoors or under overcast skies, higher values to
reduce loss of detail in highlights and shadows when photographing high-contrast scenes. Higher values are recommended
for scenes that include both sunlight and deep shade, for such high-contrast subjects as sunlight on water, brightly-lit autumn
leaves, and portraits taken against a blue sky, and for white objects or people wearing white; note, however, that mottling may
appear in pictures taken at higher values.
R If AUTO is selected, shutter speed and aperture will be displayed when the shutter button is pressed halfway.
R B200% is available at sensitivities of ISO 400 and above, C400% at sensitivities of ISO 800 and above.
PFILM SIMULATION
(defaults to <)
Simulate the effects of different types of film (P54).
tND FILTER
(defaults to OFF)
Turn the ND filter on or off (P57).
dWB SHIFT
Press the command dial up or down to fine-tune white balance on the selected color axis (Red–Cyan or
Blue–Yellow) by +9 to –9 in increments of one. Press MENU/OK to select.
Red
Blue
Cyan
Yellow
fCOLOR
(defaults to MID)
Adjust color density.
70
Using the Menus: Shooting Mode
HSHARPNESS
(defaults to STANDARD)
Sharpen or soften outlines.
rHIGHLIGHT TONE
Adjust the appearance of highlights.
(defaults to STANDARD)
(defaults to STANDARD)
(defaults to STANDARD)
(defaults to tAREA)
sSHADOW TONE
Adjust the appearance of shadows.
hNOISE REDUCTION
Reduce noise in pictures taken at high sensitivities.
FAF MODE
Choose how the camera selects the focus area when in AF-S focus mode.
• sMULTI: When the shutter button is pressed halfway, the camera detects high-contrast subjects and selects the focus area
automatically.
• tAREA: Choose the focus area manually (P50).
IFLASH
(defaults to 0)
/
/
Adjust flash brightness. Choose from values between +2 3EV and –2 3EV. Note that the desired results may not be achieved
depending on shooting conditions and the distance to the subject.
gEXTERNAL FLASH
(defaults to OFF)
Choose ON when using an optional third-party flash unit mounted on the camera hot shoe, or ON (COMMANDER) to control
optional remote flash units using the camera’s built-in flash. No adjustment is required with optional FUJIFILM flash units.
R See the documentation provided with the flash unit for details. The camera can be used with flash units that provide aperture
adjustment, external metering, and sensitivity control. Some flash units that are designed specifically for other cameras can
not be used.
71
Using the Menus: Shooting Mode
uSELECT CUSTOM SETTING
Recall settings saved with KEDIT/SAVE CUSTOM SETTING.
KEDIT/SAVE CUSTOM SETTING
Save settings (P55).
vDISP. CUSTOM SETTING
Choose the items displayed in the optical viewfinder or in the electronic viewfinder and LCD monitor (P20). The following items
can be displayed: framing grid (you can also select the grid type as described on page 86), virtual horizon, autofocus distance (fo-
cus distance is always displayed in manual focus mode), histogram, exposure (shutter speed, aperture, and sensitivity), exposure
compensation/exposure indicator, metering, flash mode, white balance, film simulation, dynamic range, number of exposures
remaining, image size and quality, and battery level. See pages 6–7 for the locations of these items in the displays.
Highlight OVF or EVF/LCD and press MENU/OK.
1
2
Press the command dial up or down to highlight items and press MENU/OK to select or deselect. Press DISP/BACK to exit when
settings are complete.
Virtuaal HHorizon
Seelleeccttingg ELECTRONIC LEVEL dispplays a virttual hhorizzoonn.. TThe cameraa is leevveell wwhheenn tthhee ttwwoo lliinneess oover-
lap.
R The virtual horizon may not be displayed if the camera lens is pointed up or down.
72
Using the MMenus: Playbbaacckk MMode
To display the playback menu, press MENU/OK in playback mode. Highlight items
and press the command dial right to view options, then highlight an option and
press MENU/OK. Press DISP/BACK to exit when settings are complete.
Playback Menu Options
mPHOTOBOOK ASSIT
Create books from your favorite photos (P63).
tIMAGE SEARCH
Search for pictures (P62).
AERASE
Delete all or selected pictures (P67).
73
Using the Menus: Playback Mode
jMARK FOR UPLOAD TO
Select pictures for upload to YouTube or Facebook using MyFinePix Studio (Windows only).
Select YouTube to choose movies for upload to YouTube, FACEBOOK to choose photos and movies for upload to Facebook.
1
2
Press the command dial left or right to display pictures and press MENU/OK to select or deselect. Press DISP/BACK to exit when
all the desired pictures are selected.
R Only movies can be selected for upload to YouTube.
R During playback, selected pictures are marked with jYouTube or jFACEBOOK indicators.
R Choose RESET ALL to deselect all pictures. If the number of pictures affected is very large, a message will be displayed while
the operation is in progress. Press DISP/BACK to exit before the operation is complete.
Uploadiing Picttures (Winddowss Only)
Seelleecctteedd ppiiccttuurreess ccaann bbee uuppllooaaddeedd uussiinngg tthhee YouTube/Facebook Upload op- Select with camera
tion in MyFinePix Studio. For information on installing MyFinePix Studio and
connecting the camera to a computer, see “Viewinng Pictuures onn a Compputer”
(P94).
Upload from computer
74
Using the Menus: Playback Mode
ISLIDEE SHOW
View pictures in an automated slide show. Choose the type of show and press MENU/OK to start. Press DISP/BACK at any time dur-
ing the show to view on-screen help. The show can be ended at any time by pressing MENU/OK.
Option
NORMAL
Description
Press the command dial left or right to go back or skip ahead one frame. Select FADE-IN for fade transitions be-
tween frames.
FADE-IN
NORMAL g
FADE-IN g
As above, except that camera automatically zooms in on faces.
MULTIPLE Display several pictures at once.
R The camera will not turn off automatically while a slide show is in progress.
jRAW CONVVERSION
Create JPEG copies of RAW pictures (P68).
BRED EYE RREMOVAL
Remove red-eye from portraits. The camera will analyze the image; if red-eye is detected, the image will be processed to create
a copy with reduced red-eye.
Display the desired picture.
1
Select BRED EYE REMOVAL in the playback menu.
2
3
Press MENU/OK.
R Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ depending on
the scene. Red eye can not be removed from pictures that have already been processed using red-eye removal or pictures
created with other devices.
R The amount of time needed to process the image varies with the number of faces detected.
R Copies created with BRED EYE REMOVAL are indicated by a eicon during playback.
R Red eye removal can not be performed on RAW images.
75
Using the Menus: Playback Mode
DPROTECT
Protect pictures from accidental deletion. Highlight one of the following options and press MENU/OK.
• FRAME: Protect selected pictures. Press the command dial left or right to view pictures and press MENU/OK to select or deselect.
Press DISP/BACK when the operation is complete.
• SET ALL: Protect all pictures.
• RESET ALL: Remove protection from all pictures.
Q Protected pictures will be deleted when the memory card or internal memory is formatted (P81).
GCROP
Create a cropped copy of the current picture.
Display the desired picture.
1
Select GCROP in the playback menu.
2
3
Use the kand nbuttons to zoom in and out and press the command dial up, down, left, or right to scroll the picture until
the desired portion is displayed.
Press MENU/OK to display a confirmation dialog.
4
5
Press MENU/OK again to save the cropped copy to a separate file.
R Larger crops produce larger copies; all copies have an aspect ratio of 3:2. If the size of the final copy will be a, OK will be
displayed in yellow.
76
Using the Menus: Playback Mode
eRESIZE
Create a cropped copy of the current picture.
Display the desired picture.
1
Select eRESIZE in the playback menu.
2
3
4
Highlight a size and press MENU/OK to display a confirmation dialog.
Press MENU/OK again to save the resized copy to a separate file.
R The sizes available vary with the size of the original image.
CIMAGE ROTATE
Rotate pictures.
Display the desired picture.
1
Select CIMAGE ROTATE in the playback menu.
2
3
4
Press the command dial down to rotate the picture 90 ° clockwise, up to rotate it 90 ° counterclockwise.
Press MENU/OK. The picture automatically be displayed in the selected orientation whenever it is played back on the camera.
R Protected pictures can not be rotated. Remove protection before rotating pictures (P76).
R The camera may not be able to rotate pictures created with other devices.
R Pictures taken with mAUTOROTATE PB are automatically displayed in the correct orientation during playback (P87).
77
Using the Menus: Playback Mode
ECOPY
Copy pictures between internal memory and a memory card.
Highlight one of the following options and press the command dial right.
• aINTERNAL MEMORY ybCARD: Copy pictures from internal memory to a memory card.
1
• bCARD yaINTERNAL MEMORY: Copy pictures from a memory card to internal memory.
Highlight one of the following options and press MENU/OK.
• FRAME: Copy selected pictures. Press the command dial left or right to view pictures and press MENU/OK to copy the current
2
picture.
• ALL FRAMES: Copy all pictures.
R Copying ends when the destination is full.
R DPOF print information is not copied (P91).
KPRINT ORDER (DPOF)
Select pictures for printing on DPOF- and PictBridge-compatible devices (P90, 91).
JDISP ASPECT
Choose how High Definition (HD) devices display pictures with an aspect ratio of 3:2
(this option is available only when an HDMI cable is connected). Select 16:9 to display
the image so that it fills the screen with its top and bottom cropped out, 3:2 to display
16:9
3:2
the entire image with black bands at either side.
16 : 9
3 : 2
78
The Setup MMenu
Using the Setup Menu
Display the setup menu.
1.1 Press MENU/OK to display the menu for the current mode.
1
1.2 Press the command dial left to highlight the tab for the current menu.
1.3 Press the command dial down to highlight X.
Tab
1.4 Press the command dial right to place the cursor in the setup menu.
Adjust settings.
2
Highlight items and press the command dial right to view options, then highlight an option and
press MENU/OK. Press DISP/BACK to exit when settings are complete.
79
The Setup Menu
Setup Menu Options
FDATE/TIME
Set the camera clock (P17).
NTIME DIFFFERENCE
(defaults to h)
Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the
difference between local time and your home time zone:
Highlight g LOCAL and press the command dial right.
1
2
Use the command dial to choose the time difference between local time and your home time zone. Press MENU/OK when
settings are complete.
To set the camera clock to local time, highlight g LOCAL and press MENU/OK. To set the clock to the time in your home time
zone, select h HOME. If g LOCAL is selected, g will be displayed for three seconds when the camera is turned on.
La
Choose a language (P17).
oSILENT MODE
(defaults to OFF)
Select ON to disable the speaker, flash, and illuminator in situations in which camera sounds or lights may be unwelcome.
RRESET
Reset all settings except FDATE/TIME, NTIME DIFFERENCE, and OBACKGROUND COLOR to default values. Press the
command dial right to display a confirmation dialog, then highlight OK and press MENU/OK.
80
The Setup Menu
KFORMAT
If a memory card is inserted in the camera, this option will format the memory card. If no memory card is inserted, this option
will format internal memory. Select OK to begin formatting.
Q All data—including protected pictures—will be deleted from the memory card or internal memory. Be sure important files
have been copied to a computer or other storage device.
Q Do not open the battery-chamber cover during formatting.
AIMAGE DISP.
(defaults to 1.5 SEC)
Choose how long images are displayed after shooting. Colors may differ slightly from those in the final image and “noise” mot-
tling may be visible at high sensitivities.
Option
Description
Pictures are displayed until the MENU/OK button is pressed or the shutter button is pressed halfway. To zoom in on
the active focus point, press the center of the command control; press again to cancel zoom.
CONTINUOUS
1.5 SEC
3 SEC
OFF
Pictures are displayed for three seconds (3 SEC) or 1.5 seconds (1.5 SEC) or until the shutter button is pressed
halfway.
Pictures are not displayed after shooting.
R OFF has no effect in continuous shooting mode.
81
The Setup Menu
BFRAME NO.
(defaults to CONTINUOUS)
New pictures are stored in image files named using a four-digit file number assigned by adding one to the
last file number used. The file number is displayed during playback as shown at right. BFRAME NO. con-
trols whether file numbering is reset to 0001 when a new memory card is inserted or the current memory
card or internal memory is formatted.
Frame number
100-0001
Directory
File
number number
Option
CONTINUOUS
RENEW
Description
Numbering continues from the last file number used or the first available file number, whichever is higher.
Choose this option to reduce the number of pictures with duplicate file names.
Numbering is reset to 0001 after formatting or when a new memory card is inserted.
R If the frame number reaches 999-9999, the shutter release will be disabled (P111).
R Selecting RRESET (P80) sets BFRAME NO. to CONTINUOUS but does not reset the file number.
R Frame numbers for pictures taken with other cameras may differ.
GOPERATTIONN VVOL.
(defaults to c)
Adjust the volume of the sounds produced when camera controls are operated. Choose f (mute) to disable control sounds.
HSHUTTEER VOLUME (defaults to c)
Adjust the volume of the sounds produced when the shutter is released. Choose f (mute) to disable control sounds.
eSHUTTER SOUND
(defaults to i SOUND1)
Choose the sound made by the shutter (P22).
IPLAAYYBBAACK VOLUME
(defaults to 7)
Control the volume for movie playback.
82
The Setup Menu
JLCD BRIGHTNESS
(defaults to 0)
Control the brightness of the displays.
MAUTO PPOWER OFF
(defaults to 2 MIN)
Choose the length of time before the camera turns off automatically when no operations are performed. Shorter times reduce
the drain on the battery; if OFF is selected, the camera must be turned off manually. Note that in some situations the camera
turns off automatically even when OFF is selected.
GOVF POWWEERR SSAAVE MODE
(defaults to OFF)
Select ON to reduce the drain on the battery, roughly doubling the number of pictures that can be taken on a single charge
(P23).
HQUICK START MODE
(defaults to OFF)
(defaults to NISO)
Select ON to reduce the time needed to restart the camera after it has been turned off to about 0.7 seconds (P23).
FFn BUTTON
Choose the role played by the Fn button (P53).
83
The Setup Menu
NISO AUTO CONTROL
Choose whether the camera automatically adjusts sensitivity if optimal exposure can not be achieved at current settings. Select-
ing NISO AUTO CONTROL displays the settings listed in the table below; press the command dial up or down to highlight a
setting and press the dial right to display options for the highlighted item, then highlight the desired option and press MENU/OK.
When ISO AUTO CONTROL is on, the upper limit for sensitivity is fixed at the value selected for MAX. SENSITIVITY. The camera
will not exceed this limit even if underexposure would result.
Option
Description
Default
ON
If ON is selected, the camera will automatically adjust sensitivity if optimal exposure can not be
ISO AUTO CONTROL
achieved at current settings.
Choose the upper limit for auto sensitivity from ISO 400, 800, 1600, and 3200 (the lower limit is fixed
at ISO 200).
MAXX.. SSEENNSSITIVITY
800
When the shutter speed dial is rotated to A and ISO AUTO CONTROL is ON, the camera will adjust
sensitivity only as required to prevent shutter speed from being slower than this value.
MIN. SHUTTER SPEED
1/60 SEC
R In shutter-priority AE and manual exposure modes, the camera will automatically adjust sensitivity if optimal exposure can
not be achieved at the shutter speed selected by the user.
R Sensitivity is automatically adjusted for optimal flash output when a flash is used.
R Shutter speed, aperture, and the current sensitivity are displayed when the shutter button is pressed halfway.
BRED EYE RREMOVAL
(defaults to OFF)
Choose ON to remove red-eye effects caused by the flash.
R Red-eye reduction is performed only when a face is detected.
R Red-eye removal is not available with RAW images.
84
The Setup Menu
CAF ILLUMINATOR
(defaults to ON)
If ON is selected, the AF-assist illuminator will light to assist autofocus.
R The AF-assist illuminator turns off automatically in silent mode.
Q The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable to focus in macro
mode, try increasing the distance to the subject.
Q Avoid shining the AF-assist illuminator directly into your subject’s eyes.
kAE/AF-LOCK MODE
(defaults to AE & AF ON WHEN PRESSING)
If AE & AF ON WHEN PRESSING is selected, exposure and/or focus will lock while the AFL/AEL button is pressed. If AE & AF ON/
OFF SWITCH is selected, exposure and/or focus will lock while the AFL/AEL button is pressed and remain locked until the button
is pressed again.
vAE/AF-LOCK BUTTON
(defaults to AE LOCK ONLY)
Choose the role played by the AFL/AEL button (P46).
jFOCUS CHECK
(defaults to ON)
If ON is selected, the center of frame will be magnified in the display to assist focus when the center of the command control is
pressed in manual focus mode (P48, 49).
IFOCUS RING
(defaults to XCW)
Choose the direction in which the focus ring is rotated to increase the focus distance.
MFOCUS SCALE UNITS
(defaults to METERS)
Choose the units used for the focus distance indicator (P6, 7).
85
The Setup Menu
zFRAMING GUIDLINE
Choose the type of framing grid available in shooting mode.
(defaults to FGRID 9)
HHD FRAMING
FGRID 9
GGRID 24
For “rule of thirds”composition.
A six-by-four grid.
Frame HD pictures in the crop shown by
the lines at the top and bottom of the
display.
JCOLOR SPACE
(defaults to sRGB)
Choose the gamut of colors available for color reproduction.
Option
Description
sRGB
Recommended in most situations.
Adobe RGB For commercial printing.
KLONG EXPOSURE NR
(defaults to ON)
Select ON to reduce mottling in long time-exposures (P29).
86
The Setup Menu
nSAVE ORG IMAGE
(defaults to OFF)
Choose ON to save unprocessed copies of pictures taken using BRED EYE REMOVAL.
mAUTOROTATE PB
(defaults to ON)
Choose ON to automatically rotate“tall”(portrait-orientation) pictures during playback.
OBACKGROUNND COLOORR
Choose a color scheme.
cGUIDANCE DISPPLLAY
(defaults to ON)
Choose whether to display tool tips.
GCORRECTEED AF FRAME
(defaults to OFF)
If ON is selected, a second focus frame for focus distances of about 80cm (2.6ft) will be added to the display in the optical view-
finder. The focus frame for the current focus distance is displayed in green when the shutter button is pressed halfway.
ON
OFF
Focus frame for focus distance of infinity
Focus frame
Focus frame for focus distance of
about 80 cm (2.6 ft)
87
Connections
Viewing Pictures on TV
To show pictures to a group, connect the camera to a TV using an HDMI cable (available separately
from third-party suppliers; note that the TV can only be used for playback, not shooting).
Turn the camera off.
1
Connect the cable as shown below.
2
Insert into HDMI
connector
Insert into HDMI mini
connector
R Be sure the connectors are fully inserted.
Tune the television to the HDMI input channel. See the documentation supplied with the televi-
sion for details.
3
Turn the camera on and press abutton. The camera monitor turns off and pictures and movies
are played back on the TV. Note that the camera volume controls have no effect on sounds played
on the TV; use the television volume controls to adjust the volume.
4
R The USB cable can not be used while an HDMI cable is connected.
R Some televisions may briefly display a black screen when movie playback begins.
88
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without first being copied to a computer. Note that depending on the
printer, not all the functions described below may be supported.
Connecting the Camera
Printing Selected Pictures
Connect the supplied USB cable as shown and
Press the command dial left or right
1
1
turn the printer on.
to display a picture you wish to print.
R To print one copy of the current picture, pro-
ceed directly to Step 3.
Press the command dial up or down
2
to choose the number of copies (up
to 99). Repeat steps 1–2 to select
additional pictures.
Turn the camera on and press a button.
2
tUSB will be displayed in the monitor, fol-
lowed by the PictBridge display shown below
at right.
Press MENU/OK to display a confirma-
tion dialog.
3
4
Press MENU/OK to start printing.
89
Printing Pictures via USB
R Pictures can be printed from internal memory or a
memory card that has been formatted in the cam-
era.
R Page size, print quality, and border selections are
made using the printer.
Printing the DPOF Print Order
To print the print order created with KPRINT
ORDER (DPOF) in the playback menu (P91):
In the PictBridge display, press DISP/
BACK to open the PictBridge menu.
1
Printinng thee DDaattee ooff RReecoorrding
Press the command dial up or down
to highlight uPRINT DPOF.
2
To print the date of recording on pictures, press
DISP/BACK in the PictBridge display and select PRINT
WITH DATE s (to print pictures without the date of
recording, select PRINT WITHOUT DATE). To ensure
that the date is correct, set the camera clock before
taking pictures. Some printers do not support date
printing. See the printer manual for details.
Press MENU/OK to display a confirma-
tion dialog.
3
4
Press MENU/OK to start printing.
90
Printing Pictures via USB
Creating a DPOF Print Order
During PPrinting
The KPRINT ORDER (DPOF) option in the play-
back menu can be used to create a digital “print
order” for PictBridge-compatible printers or de-
vices that support DPOF.
The message shown at right is
displayed during printing. Press
DISP/BACK to cancel before all
pictures are printed (depending
on the printer, printing may end
before the current picture has
printed).
DPOF
DPOF (Digital Print Order Format) is stan-
dard that allows pictures to be printed from
“print orders” stored in internal memory or
on a memory card. The information in the
order includes the pictures to be printed and the
number of copies of each picture.
If printing is interrupted, turn the camera off and
then on again.
Disconnecting thhee CCamera
Confirm that the above message is not displayed and
turn the camera off. Disconnect the USB cable.
91
Printing Pictures via USB
■ WITH DATE s/ WITHOUT DATE
Press the command dial up or down
to choose the number of copies (up
to 99). To remove a picture from
the order, press the command dial
down until the number of copies is 0.
2
To modify the DPOF print order, select KPRINT
ORDER (DPOF) in the playback menu and press
the command dial up or down to highlight WITH
DATE s or WITHOUT DATE.
WITH DATE s: Print date of recording
on pictures.
Total number of prints
Number of copies
WITHOUT DATE: Print pictures without
date.
Repeat steps 1–2 to complete the
print order. Press MENU/OK to save
the print order when settings are
complete, or DISP/BACK to exit without chang-
ing the print order.
3
4
Press MENU/OK and follow the steps below.
Press the command dial left or right
1
to display a picture you wish to in-
clude in or remove from the print
order.
The total number of prints is dis-
played in the monitor. Press MENU/
OK to exit.
The pictures in the current
print order are indicated by a
u icon during playback.
92
Printing Pictures via USB
R Remove the memory card to create or modify a
print order for the pictures in internal memory.
■ RESET ALL
To cancel the current print
order, select RESET ALL for
KPRINT ORDER (DPOF). The
confirmation shown at right
will be displayed; press MENU/OK
to remove all pictures from the
order.
R Print orders can contain a maximum of 999 pictures.
R If a memory card is inserted
containing a print order cre-
ated by another camera, the
message shown at right will
be displayed. Pressing MENU/OK
cancels the print order; a new
print order must be created as
described above.
93
Viewingg Picturreess oonn aa CCoommppuutter
The supplied software can be used to copy pictures to a computer, where they can be stored, viewed,
organized, and printed. Before proceeding, install the software as described below. Do NOT connect the
camera to the computer until installation is complete.
Windows: Installing MyFinePix Studio
Confirm that the computer meets the following system requirements:
1
Windows 71
Windoows Vista1
Windows XP1
3GHz Pentium 4 or better
2GHz Pentium 4 or better
CPU
(2.4GHz Core 2 Duo or better)2
(2.4GHz Core 2 Duo or better)2
512MB or more
(1GB or more)2
2GB or more
RAM
Free disk space
Video
1GB or more
15GB or more
• 1024×768 pixels or more with 24-bit color or better
• A graphics processing unit (GPU) that supports DirectX 7 or later
• Built-in USB port recommended. Operation is not guaranteed with other USB ports.
Other
• Internet connection (broadband recommended) required to install .NET Framework (if necessary), to use
auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.
1 Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not
guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.
2 Recommended when displaying HD movies.
Start the computer. Log in to an account with administrator privileges before proceeding.
2
94
Viewing Pictures on a Computer
Exit any applications that may be running and insert the installer CD in a CD-ROM drive.
3
Windoows 7/Wiindows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;
click Yes (Windows 7) or Allow (Windows Vista).
The installer will start automatically; click Install MyFinePix Studio and follow the on-screen in-
structions to install MyFinePix Studio and RAW FILE CONVERTER.
If the Installer Does Noott SSttaarrtt AAuuttoommaattiiccaalllly
If the installer does not start automatically, select Computer or My Computer from the Start menu, then
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click setup or SETUP.EXE.
If prompted to install Windows Media Player, DirectX, or .NET Framework, follow the on-screen
instructions to complete installation.
4
5
Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer
CD in a dry location out of direct sunlight in case you need to re-install the software.
Installation is now complete. Proceed to“Connecting the Camera”(P98).
95
Viewing Pictures on a Computer
Macintosh: Installing FinePixViewer
Confirm that the computer meets the following system requirements:
1
CPU
PowerPC or Intel (Core 2 Duo or better)*
Pre-installed copies of Mac OS X version 10.3.9–10.6
(visit http://www.fujifilm.com/support/digital_cameras/compatibility/ for more information)
256MB or more (1GB or more)*
OS
RAM
Free disk space A minimum of 200MB required for installation with 400MB available when FinePixViewer is running
Video
Other
800×600 pixels or more with thousands of colors or better
Built-in USB port recommended. Operation is not guaranteed with other USB ports.
* Recommended when displaying HD movies.
After starting the computer and quitting any applications that may be running, insert the installer
CD in a CD-ROM drive and double-click Installer for Mac OS X.
2
3
An installer dialog will be displayed; click Installing FinePixViewer to start installation. Enter an
administrator name and password when prompted and click OK, then follow the on-screen in-
structions to install FinePixViewer. Click Exit to quit the installer when installation is complete.
R To install RAW FILE CONVERTER, double-click SILKYRFCEXInstaller. RAW FILE CONVERTER is used to view
RAW images on your computer.
Remove the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD
if Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry
location out of direct sunlight in case you need to re-install the software.
4
96
Viewing Pictures on a Computer
Mac OS X 10.5 or earlier: Open the“Applications”folder, start Image Capture, and select Preferences…
from the Image Capture application menu. The Image Capture preferences dialog will be displayed;
choose Other… in the When a camera is connected, open menu, then select FPVBridge in the
“Applications/FinePixViewer”folder and click Open. Quit Image Capture.
5
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start Image
Capture. The camera will be listed under DEVICES; select the camera and choose FPVBridge from
the Connecting this camera opens menu and click Choose. Quit Image Capture.
Installation is now complete. Proceed to“Connecting the Camera”(P98).
97
Viewing Pictures on a Computer
Connecting the Camera
If the pictures you wish to copy are stored on a memory card, insert the card into the camera (P13).
If no card is inserted, pictures will be copied from internal memory.
1
R Windows users may require the Windows CD when starting the software for the first time.
Q Loss of power during transfer could result in loss of data or damage to internal memory or the memory
card. Insert a fresh or fully-charged battery before connecting the camera.
Turn the camera off and connect the supplied USB cable as
2
shown, making sure the connectors are fully inserted. Con-
nect the camera directly to the computer; do not use a USB
hub or keyboard.
Turn the camera on. MyFinePix Studio or FinePixViewer will start automatically; follow the on-screen
instructions to copy pictures to the computer. To exit without copying pictures, click Cancel.
3
Q If the software does not start automatically, it may not be correctly installed. Disconnect the camera and
reinstall the software.
For more information on using the supplied software, start the application and select the appropriate
option from the Help menu.
98
Viewing Pictures on a Computer
Q If a memory card containing a large number of images is inserted, there may be a delay before the software
starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
Q Make sure that the computer does not display a message stating that copying is in progress and that the
indicator lamp is out before turning the camera off or disconnecting the USB cable (if the number of im-
ages copied is very large, the indicator lamp may remain lit after the message has cleared from the computer
display). Failure to observe this precaution could result in loss of data or damage to internal memory or the
memory card.
Q Disconnect the camera before inserting or removing memory cards.
Q In some cases, it may not be possible to access pictures saved to a network server using the supplied software
in the same way as on a standalone computer.
Q The user bears all applicable fees charged by the phone company or Internet service provider when using
services that require an Internet connection.
Disconnecting thhee CCamera
After confirming that the indicator lamp is out, turn the camera off and disconnect the USB cable.
Uninstalling the Supplied Softtwwaarree
Only uninstall the supplied software when it is no longer required or before beginning reinstallation. After quit-
ting the software and disconnecting the camera, drag the “FinePixViewer” folder from “Applications” into the
Trash and select Empty Trash in the Finder menu (Macintosh), or open the control panel and use “Programs
and Features” (Windows 7/Windows Vista) or “Add or Remove Programs” (Windows XP) to uninstall MyFinePix
Studio. Under Windows, one or more confirmation dialogs may be displayed; read the contents carefully before
clicking OK.
99
Technical Notes
Oppttiioonnaall AAcccesssoories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the accesso-
ries available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.com/
products/digital_cameras/index.html.
Recharggeeable
Li-ion batteries
NP-95: Additional large-capacity NP-95 rechargeable batteries can be purchased as re-
quired.
Battery chargers BC-65N: Replacement battery chargers can be purchased as required. The BC-65N charg-
es an NP-95 battery in about 210 minutes at +20°C (+68°F).
Flash units
Shoe Mount Flash EF-20: This clip-on flash unit (powered by two AA batteries) has a Guide
Number of 20/66 (ISO 100, m/ft.) and supports TTL flash control. The flash head can be
rotated upwards 90° for bounce lighting.
Shoe Mount Flash EF-42: This clip-on flash unit (powered by four AA batteries) has a Guide
Number of 42/138 (ISO 100, m/ft.) and supports TTL flash control and auto power zoom
in the range 24–105 mm (35 mm format equivalent). The flash head can be rotated 90°
up, 180° left, or 120° right for bounce lighting.
Leeaatthher cases
LC-X100: This leather case, exclusively for use with the X100, combines practicality with the
luxury of leather and comes with a shoulder strap made of the same material. Pictures
can be taken with the camera still in its case.
100
Optional Accessories
Leennss hoods
LH-X100: This aluminum lens hood, exclusively for use with the X100, comes with an AR-
X100 adapter ring made of the same material. The adapter ring is required when attach-
ing the hood.
Adapterr rings
AR-X100: An aluminum adapter ring exclusively for use with the X100. It is used when
attaching the LH-X100 lens hood or φ49 mm filters available from third-party suppliers.
Attaching Adapter Rings and Lens Hoods
Remove the front ring.
Align the male and fe-
male threads as shown
and place the lens hood
on the adapter ring. Ro-
tate the lens hood as
shown.
1
3
R If you have trouble re-
movviinngg tthhee ffrroont ring,
grip the entire ring and
rotate itt as sshhoown.
Attach the adapter ring
as shown, with the pro-
jections facing out.
2
R Keep the front ring and lens cap in a safe place
when not in use.
R Attach the adapter ring before attaching filters from
third-party suppliers.
101
Optional Accessories
Connecting the Camera to Other Devices
■ Printing
■ Fllash Photography
FINEPIX X100
USB cable
(supplied)
EF-20 shoe mount EF-42 shoe mount
flash *
flash *
PictBridge-compatible printer†
SD/SDHC/SDXC
memory card†
■ Audio/Visual
HDMI cable†
Printer†
HDTV†
■ Coommpputer Reellatteedd
USB cable (supplied)
SD card slot or card reader
Computer†
* Available separately from FUJIFILM.
† Available separately from third-party suppliers.
102
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
Storage and Use
If the camera will not be used for an extended pe- ■ Water and Sand
riod, remove the battery and memory card. Do Exposure to water and sand can also damage the
not store or use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
camera and its internal circuitry and mechanisms.
When using the camera at the beach or seaside,
avoid exposing the camera to water or sand. Do
• exposed to direct sunlight or very high temper- not place the camera on a wet surface.
atures, such as in a closed vehicle on a sunny
■ Condensation
day
Sudden increases in temperature, such as occur
• extremely cold
when entering a heated building on a cold day,
• subject to strong vibration
can cause condensation inside the camera. If this
• exposed to strong magnetic fields, such as near
occurs, turn the camera off and wait an hour be-
a broadcasting antenna, power line, radar emit-
fore turning it on again. If condensation forms on
ter, motor, transformer, or magnet
the memory card, remove the card and wait for
• in contact with volatile chemicals such as pes-
the condensation to dissipate.
ticides
• next to rubber or vinyl products
103
Caring for the Camera
Cleaning
Traveling
Use a blower to remove dust from the lens and Keep the camera in your carry-on baggage.
monitor, then gently wipe with a soft, dry cloth. Checked baggage may suffer violent shocks that
Any remaining stains can be removed by wip- could damage the camera.
ing gently with a piece of FUJIFILM lens-cleaning
paper to which a small amount of lens-cleaning
fluid has been applied. Care should be taken to
avoid scratching the lens or monitor. The camera
body can be cleaned with a soft, dry cloth. Do not
use alcohol, thinner, or other volatile chemicals,
which can discolor the leather on the camera
body.
104
Troubleshooting
Problems and Solutions
Power and Battery
Problem
Solution
• Thhee bbaattery is exhausted: Chharge the batttery (P11) or innsert a fullly-charrgged spare bbattery (P12).
• Thhee bbaattery is inserted iincorrectly: Reeiinnsseerrtt iinn tthhee ccorrreecct oriieennttation (P12).
• Thhee bbaatttteerry-chamber cover is not latched: Lattcchh tthhe batttteery-chamber ccovveerr (P13).
The cameera does not
turn on.
• Thhee bbattery is cold: Warmm tthhee bbaatterry by placing it in a pocket or otheer waarrm plaace and reinsert it in the cameraa
immediiatteely before taking a picture.
The battery runs down
quickly.
• Thheerree iiss ddiirrtt oonn tthhee bbaatttteerryy tteerminals: CClleeaann tthhee terminalss with a sooft, dry cloth.
• AF-C is selected for focus mode: Seelleecctt aa differennt focus mode (P48).
• Thhee bbaatttery has been charggeedd mmaannyy ttiimmes: The batttteerryy hhaass rreeaacchheedd tthhee eenndd ooff iittss cchhaarrggiinngg life. Purchase aa new
battery.
The cameera turns off
suddenly.
Thhee bbaattery is exhausted: Chharge the batttery (P11) or innsert a fuully-chaarrged sparee battery (P12).
Charging does not start. Reeiinnsseerrtt tthhee bbaattery in the correct oriieenntation and make sure thatt tthhee cchhaarrggeerr iiss pplluuggggeedd iinn ((P11).
Charging is slow. Chharge the battery att room temperattuurree ((P118).
The charging lamp liigghhts, • Thheerree iiss ddiirrtt oonn tthhee bbaatttteerryy tteerminals: Clleeaann tthhee terminals with a soft, dry cloth.
but the battery does not • Thhee bbaatttery has been charggeedd mmaannyy ttiimmes: The batttteerryy hhaass rreeaacchheedd tthhee eenndd ooff iittss cchhaarrggiinngg life. Purchase aa new
charge.
batttteery. If the batttteerryy ssttiillll fails to charge, coonnttaacctt yyoouurr FFUUJJIIFFIILLMM ddeeaalleerr..
Menus and Displays
Problem
Solution
Display is not in English. Seellect ENGLISH for La (P80).
105
Problems and Solutions
Shooting
Problem
Solution
• Memory is full: Insert a new memoory cardd or dellete piicctures ((P13, 58, 67).
• Memory is not formatted: Formmaat the memory card or intteerrnal memory (P81).
• Thheeree iiss ddiirrtt oonn tthhee mmemory cardd ccoonnttacts: Cllean the coonnttaaccttss wwiitthh aa ssoofftt,, ddrryy ccllootthh..
• Thhee memory cardd iiss ddaamaged: Insert a new mmemorry card (P13).
• Thhee bbaattery is exhausted: Chharge the batttery (P11) or innsert a fullly-charrgged spare bbattery (P12).
• Thhee ccaamera has turned off automatically: Turnn tthhee ccaammeerra oon (P16).
• Thhee indicator lamp wwas oraange wwhhen yyoouu aatttteemmpptteedd ttoo rreeccoorrd a paanoramma: Waitt uunttiill tthhee iinnddiicattoorr llaammppss ttuurrns off
(P3).
Noo ppiiccture is taken when
the shutter button is
pressed.
Mottling (“noise”) appears
in the monitor or
electroniic viewfinder
when the shutter button is
pressed halfway.
Gain is increased to aid coommppoossiittiioonn wwhheenn tthhee ssuubbjjeecctt iiss ppoooorrly lit and aperture is ssttooppppeedd ddoowwnn,, wwhhiicchh mmaayy rreessuulltt
in noticeeaabbllee mmoottttlliinngg wwhheenn iimmaaggeess aarree pprreeviewweedd iinn tthhee ddiissppllaayyss.. IImmaaggeess ttaakkeenn wwiitthh tthhee ccaammeerra are unaffected.
The display goes darrkk aaffter
shooting.
The display may darkkeenn whhile thee flflaash charrges. Waait for tthhe flash tto chargee.
• Thhee ssuubbjjeecct is close to the camera: Seelleecctt macrro modee (P34).
The cameera does not ffocus. • Thhee ssuubject is far away froomm tthhe camera: Cancel macro mode (P34).
• Thhee ssuubbjjeecct is not suited to autofocus: Usse focus lock (P46) or manual focus (P48).
• Thhee flflaasshh ccaann not be used at curreenntt sseettings: Seeee tthhee lliisstt ooff tthhee sseettttiinnggss tthhaatt can bee used wwith thhe flash (P120).
• Thhee flaasshh is off (P): Chhoose a different flash mode (P32).
The flash does not fire.
• Thhee bbaattery is exhausted: Chharge the batttery (P11) or innsert a fullly-charrgged spare bbattery (P12).
• Thhee ccaammeerraa is in continuous mode: Seelleectt aa differentt ddrrive mode (P37).
• Thhee ccaammeerraa is in silent mode: Turnn ssiilleennt mode off (P22, 80).
Some flash modes are not
available.
The camera is in silentt mmooddee.. TTurn silennt mode off (P22, 80).
106
Problems and Solutions
Problem
Solution
• Thhee ssuubbjjeecct is not in range of the flash: Posittion thee subjectt in range of the flash (P33).
• Thhee flflaasshh wwiinndow is obstructed: Hold the cameraa ccoorrrreeccttllyy..
The flash does not fully
light the subject.
/
• Shutter speed is faster than 12,000s: Chhoose a slowweerr sshhuutttteer speed (P25, 27).
• Thhee lleennss iiss ddiirrtty: Clleeaan the lens (Pxi, 104).
• Thhee lleens is blocked: Keep objects away from the lens.
• sis diisplayyed duurring sshhootinng andd tthe fooccuuss ffrraammee iiss ddiissppllaayyeedd iinn rred: Chheecckk ffooccus before shooting (P31).
• kis displayed during shooting: Ussee tthe flaassh or mountt tthhee ccaammeerraa oonn aa ttrripod (P32).
• Shuttter sppeeed is sslow annd the aambiennt teemmppeerraattuurre is hhigh: This is normmaall aanndd ddooeess nnoott iinnddiiccaate a malfunction.
• Thhee ccaammeerraa hhaass bbeeeenn uusseedd ccoonnttinuously att high ttemperratures or a temperaturee wwaarrnniinngg iiss ddiissppllaayyeedd: Turn thhe cam-
era off and waait for it to cool dowwnn..
Piiccttuures are blurred.
Piiccttuures are mottled.
Playback
Problem
Solution
Piicctures are grainy.
The pictures were taken with a differeent make or modell of camera.
Playback zoom is unavail-
able.
The picttures weerre crreeaatedd using ORESIZE or with a different make or model off camera.
• Playback volume is too low: Adjust playback volume (P82).
Noo ssoouund in movie
playback.
• Thhee microopphhoonnee wwaass oobstructed: Hold the cameraa ccoorrrreeccttllyy dduurring recoorrddiinngg ((P2, 42).
• Thhee ssppeaker is obstructed: Hold the cameraa ccoorrrreeccttllyy dduurring playybbaacckk ((P2, 61).
• Thhee ccaammeerraa is in silent mode: Turnn ssiilleennt mode off (P22, 80).
Selected pictures are not Soommee ooff tthhee ppiiccttuurreess sseelleecctteedd ffoorr ddeelleettiioonn aarree pprrootteecctteedd.. RReemmoovvee pprrootteeccttiioonn uussiinngg tthhee ddeevviiccee wwiitthh wwhhiicchh iitt wwaass
deleted.
oriiggiinnally aappliieed (P76).
File numbering is unex-
pectedly reset.
The baattery--cchambbeerr ccovver waass ooppeenneed while thee cameerra was on. Turnn tthhee ccaammeerra off beeforee ooppeenniinngg tthhee bbaat-
tery-chammber ccovveerr (P12, 16).
107
Problems and Solutions
Connections/Miscellaneous
Problem
Solution
• Thhee ccaamera is not prooppeerrlly connected: Connect the cameraa pprrooppeerrly (P88). Note thaat oncee tthhe cameraa iiss ccoonn--
nected, piictures wiill be dispplayed onn tthhee TTVV iinnsstteeaadd ooff iinn tthhee ccaammeerraa moniitor.
• Input on the television is set to “TV”: Seett iinnppuutt ttoo““HHDDMMII”.
Noo ppiiccture or sound.
• Thhee vvoolume on the TV is too llow: Ussee tthe coonnttrroollss oonn tthhee tteelleevvision to adjust the vvolume.
The coomputer does not
recognize thee camera.
Bee ssuurree tthhee ccaammeerra aand computer are coorrrecttly connected (P98).
Can not traannssffeerr RRAW or
JPEG filess to computer.
Ussee tthhe bundled software tto transfer pictures (P94).
Piiccttuures can not be
printed.
• Thhee ccaamera is not prooppeerrlly connecteed: Connect the cameraa ccoorrrreeccttllyy ((P89).
• Thhee pprrinter is off: Turnn tthe priinnter on.
Only one copy is prrinted/
the daate iss nnot printed.
The priinnteer is not PiictBriiddggee ccompatible.
The camera is unrespon- • Temporary camera malfunction: Reemmoove and reinsert the battery (P12).
sive.
• Thhee bbaattery is exhausted: Chharge the batttery (P11) or innsert a fullly-charrgged spare bbattery (P12).
The camerra does not func-
tion as expected.
Reemmoovve andd rreinsert thhe battery (P12)). If the proobblem persissts, cconttaacctt yyoouurr FFUUJJIIFFIILLMM ddeeaalleer.
Noo sound.
Turnn ssiilleennt mode off (P22, 80).
108
Warning Messages and DDissplays
The following warnings appear in the display.
Warning
Description
B(red)
A(blinks red)
k
Low battery. Chharge the batttery (P11)) or inserrt a fullyy-chargeed spare bbattery (P12).
Baattery exxhausted.. CCharge thee battery (P11) oor insert aa fullly-chhaarged sparre battery (P12).
Slow shutter speed. Pictures may be bluurrred; uuse the flash or a triipod.
s
(displayed in red with
red focus frame)
The caamera can not focus. TTry onee of thee folloowing soluttions:
• Ussee ffoocus lock to focus on aanother ssubject aat the same disstance, then recoommppoosse the picture (P46).
• Ussee mmaaccrroo mmode to focus when taking close-ups (P34).
Aperture or shutter speed The subject is too briigghht or too darkk aanndd tthhee ppiiccttuurree wwiillll bbee oover- or under--eexxppoosseedd.. IIff tthhee ssuubbjjeecctt iiss ddaarrk, use the
displayed in red
flash (P32).
FOCUS ERROR
TURN OFF THE CAMERA
AND TURN ON AGAIN
Camerraa mmaallfunction. Turn the ccamera off and then on agaiin. If tthe meessagee perssiists,, cconttaacctt aa FFUUJJIIFFIILLMM ddeeaaller.
LENS CONTROL ERROR
BUSY
The memorry card iss incorrecctly forrmmaattteedd.. UUse the cameeraa tto formaat the card (P81).
• Thhee mmeemmoorryy ccaarrdd oorr iinntteerrnnaall mmeemmoorryy iiss nnoott ffoorrmmaatttteedd oorr tthhee mmeemmoorryy ccaarrdd hhaass bbeeeenn ffoorrmmaatttteedd iinn aa ccoommppuutteerr oorr ootthheerr
device: FFormmaatt the memory ccard or intteerrnal memorry usinng thee KFORMAT optioon in the caamera setup menu
(P81).
• Thhee memory carrd contacts requiree cclleaning: Clean the conttaaccttss wwith a sooft,, dry cloth.. If tthhee mmeessssaaggee iiss rreeppeeaatteedd,,
formmaat the card (P81)). If thhe messaage perrsists,, replaace the card.
CARD NOT INITIALIZED
• Caammeerra mallfunctionn: Conttact a FUJIFILM dealer.
109
Warning Messages and Display
Warning
Description
The memory card is locked. Unlock the card (P13).
PROTECTED CARD
• Thhee mmeemory cardd iiss nnoott ffoorrmmaatttted for use in the camera: Formmaat the card (P81).
• Thhee memory cardd ccoonnttacts reeqquuiirree cclleeaanniinngg oorr tthhee mmeemory cardd iiss ddaammaaged: Clean the coonttaaccttss wwiith a soft,, ddrryy
cloth. If tthe meessagee is reepeated, formmaat the card ((P81).. If thhee messaage peersistts, reeplace the card.
• Incommpatiibbllee mmeemmoorryy ccaarrdd: Use a coommppaattiibbllee ccaarrd (P15).
CARD ERROR
• Caammeerra mallfunctionn: Conttact a FUJIFILM dealer.
aMEMORY FULL
The memmory caard or iinternaal memoory iss ffull annd piccttuurreess ccaann nnoott bbee rreeccordded or ccopied. Delete pictures (P58, 67)
or inssert a mmemorryy cardd wwith moore frreee sppaacce (P13).
bMEMORY FULL
INTERNAL MEMORY IS FULL
INSERT A NEW CARD
No memory card inserted when ECOPY is selected. Insert a memory card.
NO CARD
• Memorry carrd eerror or connecttiion eerrrror: Reeiinnsseerrtt tthhee caard or tturnn tthhee ccaammeerra off and then on aggaaiinn.. IIff tthhee mmeessssaaggee
persistts, conttaacctt aa FFUUJJIIFFIILLMM dealer.
• Noott eennoough memory reemmaining to reeccoordd aaddddiittiioonnaal pictureess: Deelete ppicturres (P558, 67)) or insert aa memoorry card
with mmore frree sppaace (P13).
WRITE ERROR
• Thhee mmeemory cardd oorr iinntteerrnnaall mmeemory is not formatted: Formmaat the memory card or inntteerrnal meemory (P81).
• Thhee fifillee iiss ccoorrupt or was not creeaatteedd with the camera: The file can not be viieewed.
• Thhee memory carrd contacts requiree cclleaning: Clean the coonttaaccttss wwiitth a soft,, ddrry cloth.. If thee mmeessssaaggee iiss rreeppeeaatteedd,,
formmaat the card (P81)). If thhe messaage perrsists,, replaace the card.
READ ERROR
• Caammeerra mallfunctionn: Conttact a FUJIFILM dealer.
110
Warning Messages and Display
Warning
Description
The caameraa has run out of fraammee nnuummbbeerrss ((ccuurrrentt ffrraammee nnuummbbeerr iiss 999999--99999999)).. FFoorrmatt tthhee mmeemmoorryy ccaarrdd aanndd
select RENEW forr BFRAME NO. Taakke a piccturee to reset fframe numberingg to 1000-000001, then sseelleecctt CONTINU-
OUS for BFRAAME NO. (P82).
FRAAME NO. FULL
• A search has reetturned moree tthan 30,000 results: Chhoooossee aa ssearch thatt rreettuurrns fewer results.
• Moree tthan 999 images aree sseelleeccted for deletion: Chhoooose fewer images.
An atttteemmpptt waass mmaaddee ttoo ddeelleettee oorr rroottaattee ttoo aa pprrootteecctteedd ppiiccttuurree.. RRemovvee pprrootteeccttiioonn aanndd ttrryy aaggaaiinn ((P76).
TOO MANY FRAMES
PROTECTED FRAAME
PRESS AND HOLD
THE DISP BUTTTON TO
DEACTIVATE SILENT MODE
An atttteempt waass mmaaddee ttoo aaddjjuusstt tthhee vvoolluummee wwiitthh tthe cameraa iinn ssiilleenntt mmooddee.. EExxiitt ssiilleenntt mmooddee bbeeffoorree aaddjjuussttiinngg
the volume (P22, 80).
The piccture iis damaaggeedd oorr wwas nott created with the ccamera.
Reedd--eeyyee rreemmoovval caan not be appllied to piicctures crreatteedd wwiitthh ootthheerr ddeeviceess..
Reedd--eeyyee rreemmoovval can noot be applied tto movviieess..
The selectted picturre can not bbe rotated.
CAN NOT CROP
mCANNOT EXECUTE
FCANNOT EXECUTE
CAN NOT ROTATE
FCAN NOT ROTATE
bNO IMAGE
Mooviess can noot be roottaated.
The sourrce selected for ECOPY coonnttaaiinnss nnoo iimmaaggeess.. SSelect a different source.
aNO IMAGE
111
Warning Messages and Display
Warning
Description
The DPOFF priinntt orderr on the ccurrreennt memorry cardd conttaaiinnss mmoorree tthhaann 999999 iimmaaggeess.. CCooppyy tthhee ppiiccttuurreess ttoo iinntteerrnnaall
memory and creattee aa nneew priinnt order.
DPOF FILE ERROR
The picture can not be priinnted using DPOF.
Moovies can not be priinnted using DPOF.
CAN NOT SET DPOF
FCAN NOT SET DPOF
A coonnnneeccttiioonn eerrror occcuurrred whilee ppiiccttuurreess wweerree bbeeiinngg pprrintted or cooppiieedd ttoo aa ccoommppuutteerr oorr ootthheerr ddeevviiccee.. CCoonnfifirrmm
thatt tthhee ddeeviice is turnned on aannd that the USB cable is coonnnneeccted.
Printteerr out of ppaaper oorr iinnkk,, oorr other priinter errroor. Check printer (see printer mmaannuuaall ffoorr ddeettaaiillss)).. TToo rreessuummee pprrinttiinngg,,
turnn tthe priinnter off annd then turn itt back on.
COMMUNICATION ERROR
PRINTER ERROR
Printteerr out of paper or ink, or other priinnter errrroorr.. CCheck prriinnter ((see prriinnter mmanuall ffor dettaails).. If priinnting ddoes not
resume aautomatically, press MENU/OK to resume.
PRINTER ERROR
RESUME?
An attttempt waass mmaaddee ttoo pprrintt aa mmovviiee,, aa ppiiccttuurree nnoott ccrreeaatteedd wwiitthh tthhee ccaammeerraa,, oorr aa ppiiccttuurree iinn aa ffoorrmatt nnoott ssuupp--
ported byy tthhee pprrintteerr.. MMovviieess,, RRAAWW iimmaaggeess,, aanndd ssoommee pictures creatteedd wwiitthh ootthheerr ddeevicceess ccaann nnoott bbee pprrintteedd;; iiff
the pictture iss a stilll pictuure creeated with the cameraa,, cchheecckk tthhee pprriinntteerr mmaannuuaall ttoo ccoonnfifirrmm tthhaatt tthhee pprriinntteerr ssuuppppoorrttss
the JFIF--JPEG or Exxif-JPEGG fformmaat. If it does not,, tthhee ppiiccttuurreess ccaann nnoott bbee pprrintteedd..
CANNOT BE PRINTED
p
Turnn tthhee ccaammeerra off annd waaiitt ffoorr iitt to cooooll.. MMottling may increase in pictures taken when this waarrning is displayed.
112
Appendix
Gllossary
DPOF (Digital Print Order Format): A standard that allows pictures to be printed from “print orders”stored
in internal memory or on a memory card. The information in the order includes the pictures to be print-
ed and the number of copies of each picture.
EV (Exposure Value): The exposure value is determined by the sensitivity of the image sensor and the amount
of light that enters the camera while the image sensor is exposed. Each time the amount of light doubles, EV
increases by one; each time the amount of light is halved, EV decreases by one. The amount of light entering the
camera can be controlled by adjusting aperture and shutter speed.
Exif Print: A standard for storing information with pictures for optimal color reproduction during printing.
HDMI (High-Definition Multimedia Interface): An interface standard for the transmission of images and sound that
adds audio input to the DVI interface used to connect computers to displays.
JPEG (Joint Photographic Experts Group): A compressed file format for color images. The higher the compression
rate, the greater the loss of information and more noticeable drop in quality when the picture is displayed.
MOV: A movie file format (extension “.mov”) developed by Apple, Inc., and viewed using QuickTime Player. This
format is popular on the Internet.
White balance: The human brain automatically adapts to changes in the color of light, with the result that objects
that appear white under one light source still appear white when the color of the light source changes. Digital
cameras can mimic this adjustment by processing images according to the color of the light source. This process
is known as“white balance.”
113
Innteerrnnaall MMeemmoorryy//MMeemmoorryy CCaarrdd CCaappaacciittyy
The following table shows the recording time or number of pictures available at different image sizes.
All figures are approximate; file size varies with the scene recorded, producing wide variations in the
number of files that can be stored. The number of exposures or length remaining may not diminish at
an even rate. A limited number of test pictures can be taken when no memory card is inserted.
Medium
Internnal memoory (apppprox. 20 MB)
4 GB
8 GB
O
T
FINE
4
NORMAL
FINE
820
NORMAL
1300
1530
2470
2950
4760
5630
960
FINE
NORMAL
2620
3070
4970
5920
9570
11310
1940
2890
2890
4290
O3 : 2
O16 : 9
P3 : 2
P16 : 9
Q3 : 2
Q16 : 9
180° (Verticaall)
180° (Horiizzontal)
120° (Verticaall)
120° (Horiizzontal)
RAW
7
8
1640
1940
2530
2990
4970
7540
970
1460
1460
2180
5
7
8
14
21
2
3
3
6
960
1260
1490
2470
3750
480
720
720
1080
14
16
28
32
5
8
8
12
1440
1440
2130
1
210
50min.
420
100min.
h1280*
18sec.
* Use a Gcard or better. Individual movies can not exceed 10 minutes in length.
114
Specificcaattions
System
Model
FinePixx X100 diigitaall ccaammeerra
12.3 million
Effective pixels
Image sensor
23.6 mm × 155.8 mmm (APSS--CC formmaatt)) CCMMOOSS ((coommpplleemmeennttary meetal-ooxidee semiconductor) image sensor with
square pixels and priimmaarryy ccolor filter
Storage media
File system
• Internaal memmoory (approx. 20 MB)
• SD/SDHC/SDXC memory cards
Compliaant with Design Rule for Cameera File System (DCF), Exif 2.3, and Digital Print Order Formmaat (DPOF)
File format
• Still ppicturres: Exif 2.3 JPEG (compressed); RAAW (origiinnaall RRAAFF ffoorrmmaatt,, ssppeecciiaall--ppuurrppoossee ssooffttwware required); RAWW++JPG avvailable
• Movies: H.264 standard with stereo sound (MOV)
Image size
• O3 : 2: 4,288 × 2,848
• P3 : 2: 3,0772 × 2,048
• Q3 : 2: 2,176 × 1,448
• O16 : 9: 4,288 × 2,416
• P16 : 9: 3,0072 × 1,728
• Q16 : 9: 1,920 × 1,080
• Motion panorama 180: 2,160 × 7,680 (Vertiicaall) / 7,680 × 1,440 (Horiizzontal)
• Motion panorama 120: 2,160 × 5,120 (Vertiicaall) / 5,120 × 1,440 (Horiizzontal)
Lens
FUJINON fixed focal length lens
f=23 mm (355 mm forrmat equivalent: 35 mm)
F2.0
Focal length
Maximum aaperture
Aperture
/
F2.0 – F16 in steps of EV (9--blade diiaphragm)
Focuss range
Approx. 80 cm (2.66 fft.)–∞
(distance from front of lens) • Maaccrro (F) mode: 10 cm (3.9 in.) – 2.0 m (6.66 fft.)
/
Sensitivity
Sttaannddaarrdd oouuttput sensitivity equivaalleentt ttoo IISSOO 220000––66440000 iinn iinnccrreemmeennttss ooff EV; extennded ouutput seensitiivity eequiva-
lentt IISO 100 or 12800; auto ssensiittivityy conttrrooll aavvaaiillable
Metering
256-seegment through-the-lens (TTL) meteerriing; MULTI, SPPOOTT,, AAVVEERRAGE
Exposurree ccontrol
Programmed AE (with progrraamm sshhiifft); shutter--pprriioorriity AE; aperture-prioriittyy AAEE;; manual eexposure
/
Exposure compensation –2 EV – +2 EV in incremmeennts of EV
115
Specifications
System
*
*
/
/
/
Shhuutttter speed (combined • P mode: sec. to sec.
• All other modes: 30 sec. to sec.
mechanicaall and electronic
shutter)
• Bulb: Maaxx.. 60 min.
/
/
* sec aat F2, and seec att FF88 oorr smaller aperture
Continuous
Focus
Up to 10 JPEG, 8 RAWW, or 88 RAAWW++JJPPEG immagess at 5 oorr 33 ffppss
• Mode: Sinngle orr cconttiinnuuoouuss AAFF;; mmaannuuaall ffooccuuss wwiitthh ffooccuuss rring
• Focuss-area selection: Multi, area with focus area size selection (five steps)
• Autofoccus systemm: Contraasstt--ddeetteecctt TTTTLL AAFF wwiitthh AAFF--aassssiisst illuminattoorr
Whhite balance
Customm, color temperrattuurree sseellection, auto, ddirectt sunnlliigghht,, sshade, daylight fluuoresceenntt,, wwaarrmm wwhhiittee flfluuoorreesscceenntt,,
cool whiite fluoorreesscceennt, incandeessccent,, uunderrwatteerr
Self-timer
Flash
Off, 2 sec., 10 sec.
Auto flash; effectivee range att IISSOO 11660000 is approx. 50 ccm – 9 m // 1.6 fftt.. –– 2299..55fftt..;; aaccccessorry shooe withh TTTTLL ccontacts
Mode
Auto, fill flflash, off, slooww ssyynncc (red-eeye rreemmooval offff); autoo with rred-eyyee rreemmoovaall,, fifillll flflaasshh wwiitthh rreedd--eeye removvaall,, ooffff, sloww
sync with red-eyyee rreemmoovaall (red-eyee remooval on)
Hybrid vviewfinder
• Optical viewfinder: Reevveerrssee GGaalliilleeaann vviieewwfifinnddeerr wwiitthh eelleeccttrroonniicc bbrriigghhtt ffrrame diisplayy and approx. 0.5 × magnificcaa--
tions; ffrrame covveerraaggee aapppprrooxx.. 9900%%
• Electroonniicc viewfinder: 0.47-in., 1,440k-dot color LCD viewwfifinder; diopter adjustment –2 – +1 m–1 (dpt); eye pointt
approx. 155 mmmm;; ffrrame ccovveerraaggee aapppprrooxx.. 110000%
LCD monitor
Movies
2.8-in.., 446600kk--ddoott ccolloorr LLCCDD mmoonniittoorr;; ffrraammee ccooveraaggee approx. 100%
h (1,280 × 720); 24 fps; stereo sound; maximum length 10 minutes
Languages
Araabbiicc,, BBuullggaarrian, Simplified Chhiinneessee,, TTrraaddiittiioonnaall CChhiinneessee,, CCzzeecchh,, DDaanniisshh,, DDuuttcchh,, EEnngglliisshh,, FFaarrssii,, FFiinnnniisshh,, FFrreenncchh,, GGer--
man, Greeek, Hebrreww,, HHuunnggaarriiaann,, IInnddoonneessiiaann,, IIttaalliiaann,, JJaappaanneessee,, KKaazzaakkhh,, KKoorreeaann,, LLaatviian, Litthuaniaan, Norwwegian,
Polish, Portuguese, Romannian, RRussiian, SSeerrbbiiaann,, SSlloovvak, Spanissh, Swweedish, Thai, Turkkiisshh,, Ukrrainian, Vietnamese
116
Specifications
Input/output terminals
HDMI output
HDMI minni connector
USB 2.0 High-Speed
Digital input/output
Power supply/other
Power supply
NP-95 rrecharggeablee bbaattery
Battery liife (approximate
numberr of fraames thhaatt ccan
be takeen withh a fullly-charged
battery)
Battery type
NP-95 (typpe supppllied witthh ccamera)
CIPA staandard,, mmeasuredd using bbattery supplied with ccamera and SD memory card.
Notte: NNumberr of shhoots thhaat can be ttakenn wwith baattery vaarries wwith baattery charge levveell aanndd wwiillll ddeecclliinnee aatt lloow
temperrattuures.
Approoximate number of frames
300
Camera size (W × H × D) 126.5 mm × 74.4 mm × 53.9 (31.0*) mm / 5.0 in. × 2.9 in. × 2.1 (1.2*) in.
* Excludding proojectinng parttss, measuureedd aat the thinnesst part
Camera wweight
Approx.. 405 g / 114.3 oz.., excludding battery, accceessssoorriieess,, and memory card
Approxx. 445 gg // 15.7 ozz., inccludinng battery and memorry card
Shhoooottiinngg wweeiigghht
Operatingg conditions
• Temperatuurre: 0 °C to +440 °C // +32 °FF to +104 °F
• Humidity: 10% – 80% (no condensation)
117
Specifications
NP-95 rechargeable battery
Noomminal voltage
DC 3.6V
Noomminal capacity
1,800 mAh
Operating teemperrature
0 °C to +40 °C/+32 °F to +104 °F
Dimensions (W × H × D) 35.2 mm × 49.5 mm × 10.8 mm / 1.3 in. × 1.9 in. × 0.4 in.
Weight
Approx. 39 g / 1.3 oz.
BC-65N battery charger
Raatteedd input
100V – 240V AC, 50/60 Hz
15VA
Input capacity
Raatteedd ooutput
4.2V DC, 650 mA
Supported batteries
Charging time
NP-95 rechargeable batttteerries
Approx. 210 minutes (+20 °C/+68 °F)
0 °C to +40 °C/+32 °F to +104 °F
Operating teemperrature
Dimensions (W × H × D) 65 mm × 25.3 mm × 80 mm/2.5 in. × 0.9 in. × 3.1 in., excluding projections
Weight Approx. 59 g/2.0 oz., excluding battery
Weight and dimensions vary with the country or region of sale. Labels, menus, and other displays may differ from those on the
actual camera.
118
Specifications
■ Noottiices
• Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/
digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual.
• Although the electronic viewfinder and LCD monitor are manufactured using advanced high-precision technol-
ogy, small bright points and anomalous colors may appear, particularly in the vicinity of text. This is normal for
this type of LCD display and does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electricity,
or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.
119
Restrictions on Camera Settings
The options available in each shooting mode are listed below.
Option
(Macro Mode)
P
S
✔
A
✔
M
✔
✔
r F
1
Option
BSELF-TIMER
P
S
A
M
r F
1
OFF
F
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
F
H (12800)
6400
5000
4000
3200
2500
2000
1600
800
640
500
400
200
L (100)
O
✔
✔
AUTO
N
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
B
OFF
O
P
N
(Flash)
K
L
M
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
B
ON
NISO
P
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
WB (White Balance)
✔
✔
5 fps
3 fps
O
I(Continuous)
W
X
Y
o
p
q
AF-C
AF-S
MF
Bracketing
OIMAGE SIZE
P
2
2
4
✔
✔
Q
✔
Metering
FINE
✔
✔
NORMAL
FINE+RAW
NORMAL+RAW
RAW
TIMAGE
✔
✔
✔
✔
✔
QUALITY
3
Focus Mode
✔
✔
✔
Exposure Coommppeennssation
120
Restrictions on Camera Settings
Option
P
S
A
M
r F
Option
P
S
A
M
r F
FRAMING
GUIDLINE
ELECTRONIC
LEVEL
AF DISTANCE
INDICATOR
HISTOGRAM
APERTURE/
S-SPEED/ISO
EXP.
COMPENSATION
PHOTOMETRY
FLASH
WHITE BALANCE
FILM SIMULATION
DYNAMIC RANGE
FRAMES
REMAINING
BATTERY LEVEL
IMAGE SIZE/
QUALITY
AUTO
A
B
C
c
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
UDYNAMIC
RANGE
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
d
e
b
PFILM
SIMULATION
e
d
✔
✔
✔
✔
vDISP. CUSTOM
f
SETTING
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
f
tND FILTER
dWB SHIFT
fCOLOR
✔
✔
HSHARPNESS
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
rHIGHLIIGHT TONE
sSHADOOW TONE
hNOISE REDUCTION
✔
5
s
t
✔
✔
FAF MODE
5
HQUICK SSTART MODE
✔
✔
IFLASH
gEXTERNAL FLASH
uSELECT CUSTOM SETTING
KEDIT/SAVE CUSTOM SETTING
121
Restrictions on Camera Settings
1 Fixed at OFF.
2 Fixed at o(multi).
3 Continuous AF is used when AF-S is selected for focus mode.
4 Fixed at Q.
5 Center focus area selected automatically.
6 Automatically optimized for selected shooting mode.
Option
P
S
A
M
✔
✔
r F
ISO AUTO
CONTROL
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
NISO AUTO
MAXX.. SSEENNSSITIVITY
CONTROL
MIN. SHUTTER
SPEED
BRED EYE REMOVAL
CAF ILLUMINATOR
jFOCUS CHECK
IFOCUS RING
JCOLOR SPACE
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
6
✔
KLONG EXPOSURE NR
122
Memo
123
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
|