X2DMA400
INSTALLATION/OWNER'SꢀMANUAL
AM/FMꢀReceiverꢀwithꢀRemoteꢀControl
TM
X2DMA400ꢀOPERATION
WiringꢀDiagram
YELLOW - Rear RCA Input
Connect a portable device
BLACK - Antenna Input
Connect the vehicle antenna
RCA Preamp Outputs
External Amplifer Connections
SiriusXM Vehicle Tuner Connection
(tuner sold separately)
Steering Wheel Interface Input
(PAC SWI-PS sold separately)
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The X2DMA400 uses one
10 amp ATM fuse located
beside the wiring connector.
3
X2DMA400ꢀOPERATION
ControlꢀLocationsꢀ-ꢀReceiver
1
2
3
4
5
6
7
8
9
15
21
20 19 18
17
16
14
13
12 11 10
Source / Power (
Eject
)
12 USB Port
1
2
13
14
15
16
Preset 6 / Folder Up
Preset 5 / Folder Down
Preset 4 / Play / Pause
Preset 3 / Intro
Mute / Tag
Display
3
4
5
Volume Knob
Back / Band
Select
6
Preset 2 / Random
Preset 1 / Repeat
Tune / Track Up
Reset
17
18
19
20
21
7
Audio / Menu
Tuning Knob
Auxiliary Input
SD Card Slot
8
9
Tune / Track Down
10
11
4
X2DMA400ꢀOPERATION
ControlꢀLocationsꢀ-ꢀRemote
1
2
3
4
5
21
20
19
18
6
7
8
9
17
16
10
11
15
14
12
13
Key 9
1
2
12
13
14
15
16
17
18
Source / Power (
Select
)
Category Up (SXM)
Key 0 / Display
Category Down (SXM)
Key 7
3
Volume Up
4
Audio / Menu
Tune / Track Up
Volume Down
Mute / Tag
5
Key 8
6
Preset 4 / Play / Pause
Preset 1 / Repeat
Band / Back
7
8
Preset 2 / Random
Preset 3 / Intro
19
20
21
9
Tune / Track Down
Preset 6 / Folder Up
10
11
Preset 5 / Folder Down
5
X2DMA400ꢀOPERATION
GeneralꢀOperation
PowerꢀOn/Off
Source
Press or any other button to turn unit on. Press and hold
to turn unit off.
Press SOURCEꢀto select one of the following audio sources:
AM/FM Tuner Mode
CD Player Mode
Auxiliary Input (front/rear) Modes
USB and Operation of iPod/iPhone Modes
SD Card Mode
SiriusXM Satellite Radio Mode
When a source is selected, a red line will appear
underneath the corresponding icon in the source indicator
bar beneath the LCD.
AvailableꢀModes
SiriusXM mode will not appear unless the SiriusXM Connect
Vehicle Tuner (sold separately) is connected.
Operation of iPod mode will not appear unless an iPod
device (sold separately) has been connected.
CD, USB and SD modes will not appear unless a CD, USB
device or SD card (sold separately) have been connected.
SteeringꢀWheelꢀInterfaceꢀ
Inputꢀ
The steering wheel interface input located on the back of the
head unit allows connection to the PAC (Pacific Accessory
Corporation) SWI-PS interface module (sold separately).
To configure steering wheel controls, follow the instructions
provided with the PAC SWI-PS interface module. After
installing the interface module, insert the module's 3.5mm
jack into the port on the back of the head unit.
6
X2DMA400ꢀOPERATION
GeneralꢀOperation
AuxiliaryꢀInput Insert 3.5 mm plug to connect your portable audio device.
Volume Adjust volume using volumeꢀknobꢀ(00-46).
Mute Press MUTEꢀto silence the audio.
Press MUTE again to cancel.
Reset Press the RESET button, located in the bottom left corner of
the front panel, to reset the unit back to the factory settings
if abnormal operation occurs.
Display Press DISP to toggle between items such as clock, radio
frequency, or ID3 tag song information.
SetꢀtheꢀClock With the unit on, press and hold DISP until the clock begins
to flash, then release.
• Turn the tuningꢀknob left to adjust the hours
• Turn the tuningꢀknobꢀright to adjust the minutes.
Press DISP momentarily to save the selected time.
12/24-HourꢀClock The clock will display 12-hour AM/PM time in USA
frequency spacing mode (PM 10:00). In European frequency
spacing mode, the clock will display 24-hour time (22:00).
7
X2DMA400ꢀOPERATION
SetupꢀMenu
Press and hold AUDIO/MENU for more than 3 seconds to access the setup menu, then
press AUDIO/MENU to cycle through menu options. When desired option appears in the
display, rotate the tuningꢀknob left/right to adjust or activate desired function. Press BACK
to exit any menu or submenu.
Function
Options
Action
AUTO PGM
STATIONS
Press SELECT to begin automatically programming strong radio stations
to the 6 preset buttons in the current band. (Tunerꢀmodeꢀonly)
Auto Station Store
LOCAL OFF
LOCAL ON
Activates distance tuning. (Tunerꢀmodeꢀonly)
Local/Distance
Tuning
Activates local tuning for strong station reception only. (Tunerꢀmodeꢀonly)
Programs the unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM). (Tunerꢀmodeꢀonly)
FREQ USA
FREQ EUR
Tuner
Frequency
Spacing
Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM). (Tunerꢀmodeꢀonly)
IPOD CNT FULL Programs the head unit to advanced control of the iPod/iPhone device.
Selectable iPod
Control
IPOD CNT
MANUAL
Programs the head unit to basic control of the iPod/iPhone device and
allows music to be controlled from the iPod/iPhone device.
LOUD OFF
Disables the loudness function.
Loudness
Curve
Enables the loudness function. Activating this feature will enhance the
bass and treble frequencies when listening to music at low volumes.
LOUD ON
CLOCK OFF
CLOCK ON
Programs unit to not display the clock when the power is off.
Programs unit to display the clock when the power is off.
Enables the front panel 3.5mm auxiliary input.
Clock
Display
AUX FRNT ON
Front Auxiliary
Input
AUX FRNT OFF Disables the front panel 3.5mm auxiliary input.
AUX REAR ON Enables the rear RCA auxiliary input.
AUX REAR OFF Disables the rear RCA auxiliary input.
SUBWFR SUB Sets the Rear/Sub RCA output to Subwoofer.
SUBWFR REAR Sets the Rear/Sub RCA output to Rear Speakers.
Rear Auxiliary
Input
Subwoofer
BEEP OFF
BEEP ON
Disables the confirmation beep.
Enables the confirmation beep.
Beep
Confirmation
Programmable
Turn On Volume
Programs unit to always turn on at a specific volume
(default is OFF). Any volume level 1-46 can be selected.
PROG-VOL #
MESSAGE OFF Disables power on message. (example: GOOD MORNING)
MESSAGE ON Enables power on message to be displayed.
Power on
Message
SCROLL 15 SEC Programs unit to scroll information once every 15 seconds.
SCROLL ONCE Programs unit to scroll once, then show first 8 characters on display.
Scrolling
Option
SCROLL ON
SCROLL OFF
DIMMER HIGH
Programs unit to scroll continuously.
Programs unit to show the first 8 characters on the display.
Programs unit to the brightest illumination level.
Illumination
Dimmer
DIMMER MEDIUM Programs unit to the middle illumination level.
DIMMER LOW
DEMO OFF
DEMO ON
Programs unit to the dimmest illumination level.
Disables the demonstration mode.
Demonstration
Mode
Enables the demonstration message.
SiriusXM Setup
(Press SELECT) See page 23 for menu options.
8
X2DMA400ꢀOPERATION
AudioꢀMenu
Press AUDIO/MENU momentarily to cycle between Bass, Treble, Balance, Fader,
Equalizer, *Subwoofer, and Source Volume Level. Press BACK at any time to exit the
audio menu.
BASS
TREBLE
BALANCE
FADER
EQ
SUBWOOFER
SOURCE LEVEL
Press AUDIO/MENU until BASS appears, then rotate the
tuningꢀknob left/right to adjust (-6 minimum / +6 maximum).
Bass
Press AUDIO/MENU until TREBLE appears, then rotate the
tuningꢀknob left/right to adjust (-6 minimum / +6 maximum).
Treble
Note: Bass and Treble settings are retained for each mode
individually.
Press AUDIO/MENU until BALANCE appears, then rotate
the tuningꢀknob left/right to adjust (BALANCE LEFT 12 to
BALANCE RIGHT 12). "BALANCE EVEN" represents equal
balance.
Balance
Press AUDIO/MENU until FADER appears, then rotate the
tuningꢀknob left/right to adjust (FADER FRONT 12 to FADER
REAR 12). "FADER EVEN" represents equal fader.
Fader
EQ
Press AUDIO/MENU until EQ appears. Rotate the tuningꢀ
knob left/right to select between FLAT (default), POP, JAZZ,
CLASSIC, BEAT, ROCK and USER equalization curves. Press
SELECTꢀto confirm. Any manual adjustment to the Bass or
Treble settings are automatically saved as USER.
Press AUDIO/MENU until SUBWFR appears, then press
SELECT to confirm. Rotate the tuningꢀknob left/right to adjust
(0-12). Adjusting the level to 0 turns the subwoofer off.
*Subwoofer
*ꢀNote:ꢀSubwoofer option will not appear if the "Subwoofer"
option in the setup menu is set to REAR. Refer to page 8 for
details.
The source volume level control allows a gain adjustment
for each audio source. Set the source volume level for each
mode, depending on the relative volume of each audio source.
Source Volume Level
To set the source volume level, press AUDIO/MENU until
"SOURCE LEVEL" appears. After one second, the current
mode will appear on the display. Turn the tuningꢀknob to
adjust the audio level of the current source (-6 minimum/+6
maximum).
Note:ꢀOnly the current mode will be available for adjustment.
Change to another mode to set the source level for that mode.
9
X2DMA400ꢀOPERATION
LCDꢀIconꢀLayout
SiriusXM
StereoꢀFM
Reception
EQ
Random SignalꢀIndicator
SiriusXM
ChannelꢀNumber
Repeat
ess
Intro
CD-in
ArtistꢀName
FileꢀName
SongꢀTitle
AlbumꢀName
FolderꢀName
AM/FMꢀTunerꢀOperation
SeekꢀTuning Press TUNE
or TUNEꢀ
to seek the next strong
nn
ll
station.
ManualꢀTuning Rotate the tuningꢀknob to move radio frequency up or down
one step at a time.
Tuningꢀ-ꢀRemoteꢀControl Using the remote control:
• Press TUNE
or TUNEꢀ
momentarily to perform
nn
ll
Manual Tuning.
• Press and hold TUNE
or TUNEꢀ
for 1 second,
nn
ll
then release then release, to perform Seek Tuning.
Bandꢀ Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands. Up to six presets can be programmed for each
band.
StoringꢀandꢀRecallingꢀ Up to 18 FM stations and 12 AM stations can be stored in
StationꢀPresets memory.
To store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than two
seconds. When stored, the preset number will appear in the
display.
The station can be recalled by pressing the corresponding
preset button.
10
X2DMA400ꢀOPERATION
CDꢀPlayerꢀOperation
InsertꢀCD With the label facing up, insert a standard size CD into the
CD slot. The CD will automatically begin playback.
EjectꢀCD Press EJECT to eject the CD. The unit will change to
previous mode of operation. If the disc is not removed
within 10 seconds, the unit will reload the disc. The unit
does not have to be turned on to eject CD.
TrackꢀSelect Rotate tuningꢀknob right to skip to the beginning of the next
track. Rotate tuningꢀknobꢀleft to return to the beginning of
the current track. Rotate tuningꢀknob left again to skip to the
beginning of the previous track.
FastꢀForward/Reverse Press and hold TRACKꢀ
or TRACK
to fast forward
ll
nn
or reverse a track.
Press
Press
/
/
II to temporarily stop CD playback.
Pause
Intro
l
l
II again to resume playback.
Press INTꢀto enter the Intro menu, then turn the tuningꢀknob
to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays the first 10 seconds of each track.
Press RPTꢀto enter the Repeat menu, then turn the tuningꢀ
knob to select one of the following options:
• ALL - Plays all tracks on CD.
Repeat
• ONE - Continuously repeats selected track.
Press RDMꢀto enter the Random menu, then turn the tuningꢀ
knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
Random
• ALL - Plays all tracks in random order.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CD-R/CD-RWꢀ
Compatibility
CDs exposed to extreme temperatures or direct sunlight
for extended periods of time, CDs recorded in which a
recording session failed or a re-recording was attempted
and, or encrypted or copy-protected CDs which do not
conform to the audio CD-DA red book recording standard.
11
X2DMA400ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
MP3/WMAꢀDiscs When an MP3/WMA encoded disc is first inserted,
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
FolderꢀAccessꢀ Press
to select the next folder.
to select the previous folder.
Press
*Folder access is only available on discs recorded with
more than one folder.
Repeat Press RPTꢀto enter the Repeat menu, then turn the tuningꢀ
knob to select one of the following options:
• ALL - Plays all tracks on CD.
• ONE - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in the folder.
Random Press RDMꢀto enter the Random menu, then turn the tuningꢀ
knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL - Plays all tracks in random order.
• FOLDER - Plays all tracks in the folder in random order.
Note: Random mode is retained in memory when selecting
between other modes and when the unit is turned on/off.
Intro Press INTꢀto enter the Intro menu, then turn the tuningꢀknob
to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in folder.
Note: Folder repeat, random and intro options only function
on MP3/WMA discs recorded with more than one folder.
DisplayingꢀInformation Press DISPꢀmomentarily to select between artist/song title
(default), file/folder name, track number/clock & elapsed
time.
(LINE 1)
(LINE 2)
ARTIST
SONG TITLE
FILE NAME
FOLDER NAME
ELAPSED TIME
CLOCK
TRACK NUMBER
TOTAL TRACKS
“NO ARTIST” or "NO TITLE" will be displayed if the file
contains no ID3 tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
12
X2DMA400ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
File/FolderꢀSearch Press SELECTꢀto enter the file/folder search mode. A list of
all the folders from the CD will be displayed.
Note: Any files located in the root directory will be located in
the folder named "ROOT".
ChooseꢀaꢀFolder Turn the tuningꢀknobꢀto cycle through all the folders on the
CD, and press SELECTꢀto choose the desired folder. The
list of files in the selected folder will be displayed. Turn the
tuningꢀknob to cycle through the list of files.
MenuꢀNavigation Pressing BACK when viewing the contents of a folder will
return to the list of folders on the CD. Press BACK again to
exit the search menu.
PlayingꢀaꢀSong Once the desired song is displayed, press SELECT to begin
playback of the desired song.
Press SELECT
to begin
Press
SELECT
Folder 1 Folder 2 Folder 3 Folder 4 Folder 5 Folder 6 Folder 7
Press
BACK
Files
Files
Files
Files
Files
Files
Files
SELECT
Turn the
Tuning Knob
13
X2DMA400ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
File/FolderꢀCompatibilityꢀandꢀSupport
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA (digital audio)
CompatibleꢀFileꢀTypes
• MP3 data (.mp3)
• WMA data (.wma)
• AAC data (.m4a)
• WAV lossless
• FLAC lossless
• OGG data
• DRM protected files
IncompatibleꢀFileꢀTypes
• WMA lossless
• Apple lossless
• WMA Pro
• MP3 Pro
• MP3 playlists
• ISO9660 level 1 & level 2
RecordingꢀFormatꢀ
• Yellow book MODE 1 & MODE 2 FORM 1
Compatibility
• Multi session
SamplingꢀFrequencyꢀ • MP3: 8kHz ~ 48kHz
RateꢀCompatibility
TransferꢀBitꢀRateꢀ
Compatibility
• WMA: 32kHz ~ 48kHz
• MP3: 32kbps ~ 320kbps
• WMA: 32kbps ~ 192kbps
• Song Title: 32 characters
• Artist Name: 32 characters
• Album Name: 32 characters
• File Name: 32 characters
• Folder Name: 32 characters
• MP3 Tags: Version 1.0 ~ 2.4
• WMA Tags
CharacterꢀSupport
ID3ꢀTagꢀSupport
File/FolderꢀLimit
• Maximum files: 999
• Maximum folders: 255
• Maximum folder levels: 8
14
X2DMA400ꢀOPERATION
OperationꢀofꢀiPod/iPhone
ConnectingꢀanꢀiPod/iPhoneꢀDevice
USBꢀConnection Using the "dock connector to USB" sync cable (provided
with the iPod/iPhone device), plug the USB cable into the
X2DMA400's USB port. Once connected, playback will begin
automatically.
ControllingꢀaꢀDevice:ꢀFullꢀControl
WhenꢀtheꢀcontrolꢀofꢀiPod/iPhoneꢀfeatureꢀisꢀsetꢀtoꢀ"FULL"ꢀinꢀtheꢀiPodꢀMenu,ꢀuseꢀtheꢀ
followingꢀfunctionsꢀtoꢀcontrolꢀtheꢀdevice:
ꢀꢀꢀꢀSongꢀSelect
Rotate tuningꢀknob right to skip to the beginning of the next
track. Rotate tuningꢀknobꢀleft to return to the beginning of
the current track. Rotate tuningꢀknob left again to skip to the
beginning of the previous track.
ꢀꢀFastꢀForwardꢀandꢀ
Press and hold
song.
or
to fast forward or reverse a
ll nn
Reverse
ꢀꢀ
Pause
Press
Press
/
/
II to temporarily stop playback.
l
l
II again to resume playback.
Repeat
Press RPTꢀto enter the Repeat menu, then turn the tuning
knob to select one of the following options:
• ALL - Repeats all tracks.
• SONG - Repeats selected track.
Random
Press RDMꢀto enter the Random menu, then turn the tuning
knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL - Plays all tracks in random order.
• ALBUM - Plays all tracks in the selected album in
random order.
Intro
Press INTꢀto enter the Intro menu, then turn the tuningꢀknob
to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ON - Plays first 10 seconds of each track.
15
X2DMA400ꢀOPERATION
OperationꢀofꢀiPod/iPhone
ControllingꢀaꢀDevice:ꢀFullꢀControlꢀ-ꢀMusicꢀSearchꢀMenu
TheꢀX2DMA400ꢀfeaturesꢀaꢀpowerfulꢀmusicꢀsearchꢀthatꢀsimplifiesꢀtheꢀsearchingꢀprocess.ꢀ
Followꢀtheꢀstepsꢀbelowꢀtoꢀfindꢀtheꢀdesiredꢀsong:
BeginꢀSearching Press SELECT to begin the search. The main search menu
will appear.
SelectꢀaꢀCategory Turn the tuningꢀknob to select between artists, albums,
songs,ꢀplaylists,ꢀpodcastsꢀandꢀaudiobooks. Press SELECT to
select the desired search category. Some categories have
subcategories to navigate through. See the table below for
details.
Menu Navigation
Songs
Search Category
Artists
Albums
Menu
Menu
Menu
Menu
Menu
Menu
Artists
Albums
Songs
Albums
Songs
Songs
Playlists
Podcasts
Audiobooks
Playlists
Podcasts
Audiobooks
Songs
StepꢀBackwards Press BACK to return to the previous menu, or exit the
search menu when the main menu is shown.
PlayingꢀaꢀSong Navigate to the desired song/podcast/audiobook and press
SELECT to begin playback.
Note: If a specific category is selected, the iPod/iPhone
device playback will be limited to that category until another
category is selected in the search menu.
DisplayedꢀInformation
DisplayingꢀInformation Press DISP momentarily to select file/folder name (default),
song title/artist, track number/clock & elapsed time.
(LINE 1)
(LINE 2)
ARTIST
SONG TITLE
ARTIST
ALBUM
ELAPSED TIME
CLOCK
TRACK NUMBER
TOTAL TRACKS
Maximum character display information
• *Song Title – 32 character maximum
• *Artist Name – 32 character maximum
• *Album Name - 32 character maximum
CharacterꢀSupport
*Song Title, Artist Name and Album Name will only be
displayed if included with the file.
16
X2DMA400ꢀOPERATION
OperationꢀofꢀiPod/iPhone
ControllingꢀaꢀDevice:ꢀManualꢀControl
WhenꢀtheꢀcontrolꢀofꢀiPod/iPhoneꢀfeatureꢀisꢀsetꢀtoꢀ"MANUAL"ꢀinꢀtheꢀiPodꢀMenu,ꢀuseꢀtheꢀ
followingꢀfunctionsꢀtoꢀcontrolꢀtheꢀdevice:
ManualꢀControlꢀforꢀiPod When "MANUAL" control is selected from the iPod Menu,
the iPod or iPhone device can be controlled directly from the
device's interface. All functions except for volume can be
used from the iPod or iPhone device.
BasicꢀHeadꢀUnitꢀControl In addition to manual control of the iPod/iPhone device, the
following basic functions are still active:
ꢀSongꢀSelect Rotate tuningꢀknob right to skip to the beginning of the next
song. Rotate tuningꢀknob left to return to the beginning of
the current song. Rotating tuningꢀknob left again skips to the
beginning of the previous song.
ꢀꢀ
Pause Press
/
/
II to temporarily stop playback.
l
l
Press
II again to resume playback.
Volume When playing an iPod device, the volume is adjustable using
the volumeꢀknob.
DeviceꢀCompatibility
• iPod touch (4th generation)
• iPod touch (3rd generation)
• iPod touch (2nd generation)
• iPod classic
Madeꢀfor
• iPod nano (6th generation)
• iPod nano (5th generation)
• iPod nano (4th generation)
• iPhone 4
• iPhone 3GS
• iPhone 3G
17
X2DMA400ꢀOPERATION
USB/SDꢀCardꢀOperation
ConnectingꢀaꢀUSBꢀDevice To play MP3/WMA files from most mass storage
(soldꢀseparately) devices,connect a device to the X2DMA400's USB port.
ConnectingꢀaꢀSDꢀCard To play MP3/WMA files from an SD Card, insert an SD card
(soldꢀseparately) into the X2DMA400's SD card slot with the label facing up,
and press the card until it clicks into place. Remove the SD
card by pressing in until it clicks, then pull to remove.
PlayingꢀMusic When a USB or SD card device is first connected, playback
will begin momentarily. Depending on the number of files
and folders, it may take several seconds for the device to
begin playing. If no valid MP3/WMA files are detected, “NO
FILE” will be displayed.
TrackꢀSelect Rotate tuningꢀknob right to skip to the beginning of the next
track. Rotate tuningꢀknobꢀleft to return to the beginning of
the current track. Rotate tuningꢀknob left again to skip to the
beginning of the previous track.
FastꢀForwardꢀandꢀReverse Press and hold TRACKꢀ
or TRACK
to fast forward
ll
nn
or reverse a track.
Pause Press
/
/
II to temporarily stop USB playback.
l
l
Press
II again to resume playback.
FolderꢀAccessꢀ Press
to select the previous folder.
to select the next folder.
Press
Note: Folder access is only available on USB/SD Card
devices with more than one folder.
Repeat Press RPTꢀto enter the Repeat menu, then turn the tuningꢀ
knob to select one of the following options:
• ALL - Plays all tracks on the USB/SD Card device.
• ONE - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in selected folder.
Random Press RDMꢀto enter the Random menu, then turn the tuningꢀ
ꢀ
knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL - Plays all tracks in random order.
• FOLDER - Plays all tracks in folder in random order.
Note: Random mode is retained in memory when selecting
between other modes and when the unit is turned on/off.
Intro
Press INTꢀto enter the Intro menu, then turn the tuningꢀknob
to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in folder.
18
X2DMA400ꢀOPERATION
USBꢀ/ꢀSDꢀCardꢀOperation
FileꢀandꢀFolderꢀSearch
BeginꢀSearching Press SELECT to enter the file/folder search mode. A list of
all the folders from the USB/SD device will be displayed.
Note: Any files located in the root directory will be located in
the folder named "ROOT".
ChooseꢀaꢀFolder Turn the tuningꢀknob to cycle through all the folders on the
device, and press SELECT to choose the desired folder. The
list of files in the selected folder will be displayed. Turn the
tuningꢀknob to cycle through the list of files.
MenuꢀNavigation Pressing BACK when viewing the contents of a folder will
return to the list of folders on the USB device. Press BACK
again to exit the search menu.
PlayingꢀaꢀSong Once the desired song is displayed, press SELECT to begin
playback of the desired song.
Press SELECT
to begin
Press
SELECT
Folder 1 Folder 2 Folder 3 Folder 4 Folder 5 Folder 6 Folder 7
Press
BACK
Files
Files
Files
Files
Files
Files
Files
SELECT
Turn the
Tuning Knob
DisplayedꢀInformation
Press DISP momentarily to select between artist/song title (default), file/folder name track
number/clock & elapsed time.
(LINE 1)
(LINE 2)
ARTIST
SONG TITLE
FILE NAME
FOLDER NAME
ELAPSED TIME
CLOCK
TRACK NUMBER
TOTAL TRACKS
19
X2DMA400ꢀOPERATION
USBꢀ/ꢀSDꢀCardꢀOperationꢀ
File/FolderꢀCompatibilityꢀandꢀSupport
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA (digital audio)
• MP3 data (.mp3)
CompatibleꢀFileꢀTypes
• WMA data (.wma)
• AAC data (.m4a)
• WAV lossless
• FLAC lossless
• OGG data
• DRM protected files
• WMA lossless
IncompatibleꢀFileꢀTypes
• Apple lossless
• WMA Pro
• MP3 Pro
• MP3 playlists
• ISO9660 level 1 & level 2
RecordingꢀFormatꢀ
• Yellow book MODE 1 & MODE 2 FORM 1
Compatibility
• Multi session
SamplingꢀFrequencyꢀ • MP3: 8kHz ~ 48kHz
RateꢀCompatibility
TransferꢀBitꢀRateꢀ
Compatibility
• WMA: 32kHz ~ 48kHz
• MP3: 32kbps ~ 320kbps
• WMA: 32kbps ~ 192kbps
• Song Title: 32 characters
• Artist Name: 32 characters
• Album Name: 32 characters
• File Name: 32 characters
• Folder Name: 32 characters
• MP3 Tags: Version 1.0 ~ 2.4
• WMA Tags
CharacterꢀSupport
ID3ꢀTagꢀSupport
File/FolderꢀLimit
• Maximum number of files: 50000
• Maximum number of folders: 255 (plus the root folder)
• Maximum number of files in each folder: 50000
Note: For devices with more than the maximum number of files/folders,
some files will be ingnored and may not function properly.
• FAT/FAT32 file system supported.
• HFS/NTFS/EXT2/EXT3 not supported.
16GB or less supported.
USB/SDꢀFileꢀSystem
SDꢀCardꢀCapacity
20
X2DMA400ꢀOPERATION
SiriusXMꢀVehicleꢀTunerꢀConnections
Connectingꢀtheꢀ SiriusXM Satellite Radio operation requires the connection of the
SiriusXMꢀVehicleꢀTunerꢀ SiriusXM-Connect Vehicle Tuner (sold separately).
(soldꢀseparately)
Note: The SiriusXM-Connect Vehicle Tuner must have the SiriusXM
logo to be compatible with the X2DMA400.
To connect the SiriusXM Vehicle Tuner, follow the instructions
provided with the tuner. When connecting the tuner to the
X2DMA400, the cable orientation should be connected as shown
below.
X2DMA400
Head Unit
SiriusXM Vehicle
Tuner Cable
SiriusXM-Ready
Input
Line up the connector with the pins on the cable. It can only be inserted as shown above. Push the
cable into the head unit's connetor until it clicks. Attempting to insert the cable differently from shown
above may cause damage to the cable or head unit.
SiriusXMꢀVehicleꢀTunerꢀOperation
SiriusXMꢀSatelliteꢀRadioꢀ Everything worth listening to is on SiriusXM, getting over 130
Overview channels, including the most commercial-free music, plus the best
sports, news, talk and entertainment. A SiriusXM Vehicle Tuner (sold
separately) and Subscription are required. For more information,
Sirius, XM and all related marks and logos are trademarks of Sirius
XM Radio Inc. and its subsidiaries. All other marks and logos are the
property of their respective owners. All rights reserved.
TunerꢀActivation To listen to SiriusXM Satellite Radio, a subscription is required.
Activate the SiriusXM Vehicle Tuner using one of the two methods
below:
•ꢀ Phone: Call 1-800-XM-RADIO (1-800-967-2346).
Activation typically takes 10-15 minutes, but may take up to an hour.
It is recommended to leave your vehicle on until the "Subscription
Updated" message appears.
21
X2DMA400ꢀOPERATION
SiriusXMꢀVehicleꢀTunerꢀOperationꢀ
RadioꢀID To view the Radio ID on the LCD, turn the tuningꢀknob left or
right until channelꢀ0 appears. The 8 character Radio ID will
appear on the display. The Radio ID is also printed on the
underside of the SiriusXM Vehicle Tuner.
Note: The Radio ID does not use the letters I, O, S, F.
ListeningꢀtoꢀSiriusXMꢀ After installation of the SiriusXM Vehicle Tuner, press
SatelliteꢀRadio SOURCE until SiriusXM mode appears to begin listening to
SiriusXM Satellite Radio.
ChangingꢀChannels Turn the tuningꢀknob left/right to change SiriusXM channels.
Band Press BAND to select between the SXM1, SXM2 and SXM3
bands. Up to six presets can be programmed for each band,
for a total of 18 SiriusXM Satellite Radio channel presets.
SettingꢀChannelꢀPresets To store a channel, choose the desired Band (SXM1-SXM3),
then tune to the desired channel. Press and hold the desired
preset button (1-6) on the front panel or remote control for
more than two seconds. When stored, a beep sound will be
heard and the preset number will appear in the display.
RecallingꢀChannelꢀ The preset channel can be recalled by pressing the
Presets corresponding preset button.
Note: Buttons 7,8,9,0 on the remote control are not
associated with channel presets.
ChannelꢀSearchꢀList Browse through a list of all available channels.
• Press SELECTꢀto begin browsing the channel list.
• Turn the tuningꢀknob to cycle through the list of channels.
• Press SELECT to begin listening to the highlighted
channel.
Note: Press DISP to change between the channel name,
artist name, song title or content info.
CategoryꢀSearch Browse through a list of categories, and choose a channel in
the desired category.
• To begin, press TRACKꢀ
or TRACK
to cycle
ll
nn
through a list of categories. Category search can also
be performed by pressing CATꢀUP or CATꢀDOWN on the
remote control.
• Once the desired category is displayed, turn the tuningꢀ
knobꢀto browse all the channels in the selected category.
• Press SELECT to begin listening to the currently displayed
channel.
22
X2DMA400ꢀOPERATION
SiriusXMꢀVehicleꢀTunerꢀOperationꢀ
SiriusXMꢀSetupꢀMenu
To access the SiriusXM setup menu options, press and hold AUDIO/MENU for more than
3 seconds, press AUDIO/MENU to cycle through menu options until "SIRIUSXM SETUP"
appears, then press SELECT. Press AUDIO/MENU to cycle through the list of submenu
options.
Function
Action
Options
Description
EDIT
CODE
Choose this option to program a new 4-digit code. Enter the
new code using the input method described below*.
Allows channels to be locked, requiring the 4-digit code to be
entered before the channel becomes available in the channel
*Enter
Code
(default:
0000)
CHANNEL lineup. Once selected, the channel list will appear.
Parental
Controls
LOCK
• Turn the tuningꢀknob to cycle through the list of channels
• Press SELECT to lock the desired channel.
• Pressing SELECT on a locked channel will unlock it.
Choose this option to reset the locked channels back to the
factory default. All currently subscribed channels will be
unlocked.
CLEAR
ALL
Delete Tags
(iTunes
Tagging)
Press SELECT to
Deletes all Tags that are saved in memory. (Does not affect
Tags that have been transferred to an iPod device.)
confirm
SiriusXM Setup Menu Navigation
Press SELECT
Parental
Controls
*To enter a 4 digit code, choose from the two options below:
• Enter the 4 digit code using the remote control, by pressing the numbers directly. The
default code is "0000" if the code has not be changed with the "EDIT CODE" feature.
Press SELECT to confirm.
• Turn the tuningꢀknob to select the first digit, then press SELECT. Continue with the
remaining digits until all 4 digits have been entered. Press SELECT to confirm.
23
X2DMA400ꢀOPERATION
SiriusXMꢀVehicleꢀTunerꢀOperationꢀ
DisplayedꢀInformation
Display Press DISP to cycle between the following options:
(LINE 1)
(LINE 2)
CHANNEL NAME
CATEGORY
ARTIST
SONG
CONTENT INFO
CLOCK
CHANNEL Displays the name of the SiriusXM channel.
CATEGORY Displays the category type of the current channel.
ARTIST Displays the artist's name from the currently playing song.
TITLE Displays the song title from the currently playing song.
INFO Displays special channel information from the current
channel.
SiriusXMꢀAdvisoryꢀMessages
Message
Description
• Check the SiriusXM tuner connection behind the X2DMA400
to ensure that its correctly connected.
CHECKꢀTUNER
• Ensure the SiriusXM antenna cable is connected to the
SiriusXM tuner correctly.
• Check the SiriusXM antenna wire for breaks or sharp bends.
Replace the antenna if necessary.
CHECKꢀANTENNA
• Press RESET located on the bottom right corner of the front
panel. If the message remains, the antenna may have been
damaged.
• The vehicle must be outside, and the antenna must have a
clear view of the southern sky.
NOꢀSIGNAL
• The magnetic antenna must be mounted on the outside of
the vehicle for the best reception.
• This channel is not included in your SiriusXM subscription
plan. Call 1-800-XM-RADIO (1-800-967-2346) to subscribe.
CHANNELꢀUNSUB
• This channel is not a valid SiriusXM channel. The channel
number has been entered incorrectly, or the channel was
removed from the SiriusXM channel lineup.
CHANNELꢀUNAVAIL
• The selected channel has been locked by the parental control
option.
CHANNELꢀLOCKED
SUBSCRIPꢀUPDATED
• A prompt to enter the unlock code will appear. Enter the
unlock code as described on page 22.
• An update to your SiriusXM subscription has been received
by the SiriusXM tuner. Press any key to continue.
24
X2DMA400ꢀOPERATION
iTunes®ꢀTaggingꢀOperation
Requirements
The iTunes Tagging feature of the X2DMA400 requires the optional
SiriusXM Vehicle Tuner (sold separately).
Overview
iTunes Tagging allows the user to "Tag" songs that are playing on
SiriusXM Satellite Radio channel and enables them to be purchased
later through iTunes. With the touch of a button the unit will
remember the title and artist song information, and then transfer
that information to your iPod device the next time you connect it
to the X2DMA400. A new list called "Tagged" will appear in iTunes,
giving you the option to purchase each song.
TaggingꢀMusic
Stepꢀ1
Stepꢀ2
TuneꢀtoꢀaꢀSiriusXMꢀchannel. The MUTE/TAG button will illuminate
red, indicating that a valid artist name and song title are available.
PressꢀandꢀholdꢀtheꢀMUTE/TAG button. A confirmation will be
displayed, indicating that the song information has been saved. The
song information will be saved in memory until an iPod device is
plugged in. Up to 64 SiriusXM Tags can be saved before they must
be transferred or deleted.
Stepꢀ3
TransferꢀTagsꢀtoꢀanꢀiPod/iPhone.
• Connect an iPod/iPhone device. The mode will change to
operation of iPod and Tags will be automatically transferred to
the device, removing the Tags from the X2DMA400's internal
memory. A confirmation message will appear confirming the
number of tags sent. The X2DMA400 must remain in operation of
iPod mode until the "TAGS SENT" message is displayed.
• If an iPod/iPhone device is connected when a song is tagged,
Tags will transfer automatically to the device. The unit must
remain in SiriusXM mode until the "TAGS SENT" message is
displayed. (See page 17 for compatibility with iPod devices.)
Note: Tags can only be sent from SiriusXM or operation of iPod
modes.
Stepꢀ4
SyncꢀwithꢀiTunes. A list named "Tagged" will appear on the left in
the iTunes software. Click on the "Tagged" list to view all the songs
that have been tagged and click the "view" button for purchase
information.
DeletingꢀAllꢀTags
Press and hold AUDIO/MENU to enter the setup menu and select
the "Delete Tags" option. See page 22 for details.
Note: Once transferred, Tags are managed from the iTunes
software.
25
X2DMA400ꢀOPERATION
iTunes®ꢀTaggingꢀOperation
Troubleshooting
Displayed Message
Description
There is a compatibility issue with the iPod device that is connected. Check
the list of compatible iPod devices below.
CHECKꢀiPodꢀVER
If the attached iPod device is compatible, update the firmware to the latest
version using iTunes.
Tags are being sent to the iPod device. This process can take several
minutes depending on the number of Tags being sent.
SENDINGꢀTAGS
iPodꢀFULL
There is not enough space on the connected iPod device to transfer the
iTunes Tags. Free up space using iTunes.
Connection error. Ensure the iPod device is powered on and reconnect the
iPod device until a confirmation is displayed.
TRANSFERꢀFAILED
The same song has already been tagged from the same channel, and
is currently saved in memory. The same song cannot be tagged twice -
unless the song is tagged on a different channel, the Tags are sent to an
iPod device or the tags are erased.
ALREADYꢀTAGGED
The internal memory will hold 64 SiriusXM Tags. An iPod device must be
connected to transfer the Tags, or the Tags must be deleted before more
songs can be tagged.
MEMORYꢀFULL
CONNECTꢀiPod
There is not sufficient information (artist or title) to tag the song. Some HD
Radio stations or SiriusXM channels or certain songs may not fully support
iTunes Tagging.
NOꢀTAGꢀINFO
There was an error saving the Tag information to the internal memory.
TAGGINGꢀFAILED
NOꢀTAGSꢀSTORED
Press and hold theꢀMUTE/TAG button again.
There are no tags saved in the internal memory. The Delete Tags function
can only delete Tags that are saved in the internal memory.
DeviceꢀCompatibilityꢀ Compatible with:
withꢀiTunesꢀTagging • iPod touch (4th generation)
• iPod touch (3rd generation)
• iPod touch (2nd generation)
• iPod classic
• iPod nano (6th generation)
• iPod nano (5th generation)
• iPod nano (4th generation)
• iPhone 4
• iPhone 3GS
• iPhone 3G
Note: Some iPod devices may require you to select 'transfer purchases' in the context
menu from the name of your iPod device to transfer Tags to iTunes.
26
X2DMA400ꢀOPERATION
LimitedꢀOneꢀYearꢀWarranty
This warranty gives you specific legal
Whatꢀtoꢀdo?
rights. You may also have other rights
which vary from state to state.
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any
custom controls may save you a service
call.
Dual Electronics Corp. warrants this
product to the original purchaser to be free
from defects in material and workmanship
for a period of one year from the date of
the original purchase.
2. If you require service during the
warranty period, you must carefully
pack the product (preferably in the
original package) and ship it by prepaid
transportation with a copy of the original
receipt from the retailer to an
Dual Electronics Corp. agrees, at our
option, during the warranty period,
to repair any defect in material or
workmanship or to furnish an equal
new, renewed or comparable product
(whichever is deemed necessary) in
exchange without charges, subject to
verification of the defect or malfunction and
proof of the date of purchase. Subsequent
replacement products are warranted for
the balance of the original warranty period.
authorized service center.
3. Please describe your problem in
writing and include your name, a
return UPS shipping address (P.O. Box
not acceptable), and a daytime phone
number with your shipment.
4. For more information and for the
location of the nearest authorized
service center please contact us by one
of the following methods:
Whoꢀisꢀcovered? This warranty is extended
to the original retail purchaser for products
purchased from an authorized Dual dealer
and used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
Whatꢀisꢀcovered? This warranty covers all
defects in material and workmanship in
this product. The following are not covered: Exclusion of Certain Damages: This
software, installation/removal costs,
damage resulting from accident, misuse,
abuse, neglect, product modification,
improper installation, incorrect line
voltage, unauthorized repair or failure
to follow instructions supplied with the
product, or damage occurring during
return shipment of the product. Specific
warranty is exclusive and in lieu of any
and all other warranties, expressed or
implied, including without limitation the
implied warranties of merchantability and
fitness for a particular purpose and any
obligation, liability, right, claim or remedy
in contract or tort, whether or not arising
from the company’s negligence, actual
license conditions and copyright notices for or imputed. No person or representative
com.
is authorized to assume for the company
any other liability in connection with the
sale of this product. In no event shall the
company be liable for indirect, incidental or
consequential damages.
27
X2DMA400ꢀOPERATION
Troubleshootingꢀ-ꢀGeneral
Problem
Cause
Action
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Check connections for proper
voltage (11~16VDC)
Unitꢀwillꢀnotꢀturnꢀonꢀ
(noꢀpower)
Black wire not connected
Fuse blown
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unitꢀhasꢀpowerꢀ
(butꢀnoꢀsound)
Insulate all bare speaker wires
from each other and chassis
ground
One or more speaker wires touching
each other or touching chassis ground
Yellow or red wire touching chassis
ground
Check for pinched wire
Unitꢀblowsꢀfuses
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Use fuse with correct rating
PROTECTꢀappearsꢀ
onꢀdisplay
The WMA file is copy-protected by DRM Write disc using WMA files that
(Digital Rights Management)
are not copy-protected
NOꢀFILEꢀappearsꢀ
onꢀdisplay
Selected file is not available in direct or
alphanumeric search modes
Repeat search using valid
parameters
NOꢀSUPPORTꢀappearsꢀ
onꢀdisplay
Version 1.0 to 2.4 ID3 tags are
supported.
An invalid ID3 tag version is present
28
X2DMA400ꢀOPERATION
Specifications
FMꢀTuner Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AMꢀTuner Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General Speaker output impedance: 4~8ꢀohms
Line output voltage: 2ꢀVoltsꢀRMS
Dimensions: 7"ꢀxꢀ6.7"ꢀxꢀ4"ꢀ(178ꢀxꢀ170ꢀxꢀ100ꢀmm)
USB/SDꢀCard File system: FAT,ꢀFAT32
File extensions support:ꢀꢀ.mp3,ꢀ.wmaꢀꢀ
SD Card maximum device capacity: 16GB
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 18 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
29
X2DMA400ꢀOPERATION
FCCꢀCompliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
30
X2DMA400ꢀOPERATION
Notes
31
Dual Electronics Corp.
Toll Free: 1-866-382-5476
©2011 Dual Electronics Corp. All rights reserved.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or
iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for
the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with
iPod or iPhone may affect wireless performance.
Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved.
The SD logo is a trademark of the SD Card Association.
Other trademarks and trade names are those of their respective owners.
NSA1011-V01
|