MXCP44
INSTALLATION/OWNER'SꢀMANUAL
DigitalꢀMediaꢀMarineꢀReceiverꢀwithꢀ6.5"ꢀDualꢀConeꢀSpeakers
MXCP44ꢀINSTALLATION
WiringꢀDiagram
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio. The
MXCP44 uses one 10 amp
AGC fuse located in-line.
3
MXCP44ꢀOPERATION
ControlꢀLocationsꢀ-ꢀReceiver
1
2
3
4
5
15
14 13
11
7
17
16
12
10
9
6
8
Release
Preset 4 / Play / Pause
Preset 3 / Intro
Preset 2 / Random
Preset 1 / Repeat
Tune / Track Up
Tune / Track Down
Audio
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Power
Volume Knob
Band / Go Back
USB Port
Auxiliary Input
Tune / Track Up
Preset 6 / Folder Up
Preset 5 / Folder Down
Mode
4
MXCP44ꢀOPERATION
ControlꢀLocationsꢀ-ꢀRemote
1
2
3
4
5
6
17
16
7
8
15
14
9
10
13
12
11
Power
Mute
1
2
3
4
5
6
7
8
9
10
Tune / Track Down
Volume Up
Select
Preset 6 / Folder Up
Preset 4 / Play / Pause
Preset 5 / Folder Down
Preset 1 / Repeat
Preset 2 / Random
Mode
11
12
13
14
15
16
17
Volume Down
Tune / Track Up
Audio
Display
Band / Go Back
Preset 3 / Intro
5
MXCP44ꢀOPERATION
GeneralꢀOperation
FaceplateꢀRemoval
Press RELEASE and pull away from the left side to
remove. To re-install, insert right side of faceplate first
then push left side to secure.
PowerꢀOn/Off
Mode
Press ꢀorꢀanyꢀotherꢀbuttonꢀto turn the unit on. Press
again to turn the unit off.
Press MODEꢀto select between AM/FM, USB, SD or
auxiliary input modes. Modes of operation are indicated in
the display. SD and USB modes will not appear unless an
SD Card is inserted or a USB device is connected.
Display
The radio frequency (tuner mode) or MP3/WMA title/track
information (USB and SD modes) will be shown by default.
Press DISP to display the clock. The default display will
return after five seconds.
Info
Reset
When in USB or SD mode, press INFO to select between
the MP3/WMA information, including file name, song title,
artist name, album name and folder name.
Press RESET upon initial installation or if abnormal
operation occurs. Reset button is located behind the front
panel.
SetꢀtheꢀClock
Press DISPꢀto display the clock, then press and hold DISP
until the hours will flash. Rotate the volumeꢀknob to adjust
the hours. Press the volumeꢀknob, and the minutes will
flash. Rotate the volume knob to adjust the minutes.
AuxiliaryꢀInput
Insert a 3.5mm connector in the front panel AUX port.
Connect the other end of the 3.5mm connector to the
headphone output of an audio device, MP3 player, etc.
Volume
Adjust volume using theꢀvolumeꢀknob (00-40).
PresetꢀEQꢀCurves
Press EQ to select between the following preset
equalization curves: FLAT, POP, JAZZ, ROCK and OFF.
Note: Ability to manually adjust Bass and Treble settings
is disabled when a preset equalization curve is selected.
Setting equalization curves to OFF enables manual Bass
and Treble adjustments as outlined on page 7.
6
MXCP44ꢀOPERATION
GeneralꢀOperation
Press the volumeꢀknob to select between Bass, Treble,
Audioꢀ/ꢀMenu
Balance, Fader, Loudness, Distance and Stereo.
BASS TREBLE
BALANCE
FADER
LOUDNESS
DISTANCE
STEREO
Press the volumeꢀknob until BAS appears.
Rotate the volumeꢀknob left/right to adjust.
(-7 minimum / +7 maximum)
Bass
Treble
Press the volumeꢀknob until TREꢀappears.
Rotate the volumeꢀknob left/right to adjust.
(-7 minimum / +7 maximum)
Press the volumeꢀknob until BAL appears.
Balance
Fader
Rotate the volumeꢀknob left/right to adjust.
10Lꢀ(left) to 10R (right). "L=R" represents equal balance.
Press the volumeꢀknob until FAD appears.
Rotate the volumeꢀknob left/right to adjust.
10R (rear) to 10F (front) "F=R" represents equal balance.
Press the volumeꢀknob until LOUD ON or LOUDꢀOFF appears,
then rotate the volumeꢀknob to select desired option.
Activating this feature will enhance the bass and treble
frequencies when listening to music at low volumes.
Loudness
From tuner mode only, press the volumeꢀknob until DXꢀ
orꢀLOCAL appears, then rotate the volumeꢀknob to select
desired option. Selecting LOCAL programs the unit to stop at
only strong stations when seek tuning.
DistanceꢀTuning
Stereoꢀ/ꢀMono
AudibleꢀBeep
From tuner mode only, press the volumeꢀknob until STEREOꢀ
or MONO appears, then rotate the volumeꢀknob to select
desired option. Selecting MONO can improve listening in
areas with a weak FM signal.
Press and hold the volumeꢀknob until BEEP ON or BEEP
OFF appears, then rotate theꢀvolumeꢀknob to select desired
option. Activating this feature programs the unit to beep each
time certain buttons are pressed.
From tuner mode only, press and hold the volumeꢀknobꢀ
until BEEP ON or BEEP OFF appears. Press the volumeꢀknobꢀ
again to display AREA USA or AREA EURO, then rotate the
volumeꢀknob to select option appropriate for your location.
AreaꢀSelection
12/24-HourꢀClock
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10.00). In European frequency spacing
mode, the clock will display 24-hour time (22.00).
7
MXCP44ꢀOPERATION
TunerꢀOperation
SeekꢀTuning
ManualꢀTuning
Band
Press TUNE
seek the next strong station.
or TUNEꢀ
for more than 2 seconds to
momentarily to change one
nn
ll
Press TUNE
or TUNEꢀ
nn
ll
radio frequency at a time. Press and hold to advance quickly.
Press BAND to select between FM1, FM2, FM3 and AM1, AM2
bands. Six presets can be saved in each band.
StoringꢀandꢀRecallingꢀ
StationꢀPresets
Up to 18 FM stations and 12 AM stations can be stored.
To store a station, select the desired band and station.
Press and hold the desired preset button for more than 2
seconds. When stored, the preset number will appear in the
display. The station can be recalled anytime by pressing the
corresponding preset button.
AutomaticallyꢀStoreꢀ
Stations
Press AS/PS for more than 2 seconds to automatically store
all strongest stations in the current band.
After the six strongest stations are set, a scan of each stored
preset will begin. Press AS/PS or TRACK
to cancel.
ll
PresetꢀScan
Press AS/PS momentarily to scan preset stations for five
seconds each. To select a station during the scan, press
AS/PS again or press the corresponding preset button.
8
MXCP44ꢀOPERATION
SDꢀCardꢀ/ꢀUSBꢀOperationꢀ
ConnectingꢀaꢀUSBꢀDevice
(soldꢀseparately)
Play MP3/WMA/WAV files from many mass storage devices
by connecting them to the MXCP44's USB port.
InsertingꢀanꢀSDꢀCard
(soldꢀseparately)
To play MP3/WMA/WAV files from an SD card, insert an
SD card into the MXCP44's SD card slot with the label
facing left. It will click into place when properly inserted. To
remove the card, press in until it clicks, then pull to remove.
PlayingꢀMusic
TrackꢀSelect
When a USB or SD card device is first connected, playback
will begin automatically. Depending on the number of files
and folders, the device may take several seconds to begin
playback. If no valid MP3/WMA/WAV files are detected, "NO
FILE" will be displayed.
Press TRACKꢀ
track. Press TRACK
to skip to the beginning of the next
ll
to return to the beginning of the
nn
previous track.
FastꢀForwardꢀandꢀReverse
Press and hold TRACKꢀ
forward or reverse a track.
or TRACK
to fast
ll
nn
Pause
FolderꢀAccessꢀ
Intro
Press
Press
/
/
II to temporarily stop playback.
II again to resume playback.
l
l
Press
Press
to select the previous folder.
to select the next folder.
Press INT to play the first 10 seconds of each track. Press
INTꢀagain to cancel.
Repeat
Press RPT to continuously repeat the current track. Press
RPTꢀagain to cancel.
Random
Press RDM to play all the tracks in random order. Press
RDM again to cancel.
Intro, Repeat and Random functions will be kept in memory
when selecting between modes or when the unit is turned
off/on.
9
MXCP44ꢀOPERATION
SDꢀCardꢀ/ꢀUSBꢀOperation
The following types of files are compatible:
MediaꢀCompatibility
• MP3 audio
• WMA audio
• WAV audio
The following types of files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management)
• WMA lossless format
• MP3 PRO format, MP3 playlists
• AAC, protected AAC, M4A format
Playback sequence begins in the root folder. Any empty
folders or folders that do not include compatible files are
skipped. Depending on your software, the playback order
may vary.
PlaybackꢀOrder
• Maximum number of files: 9999
• Maximum number of folders: 999
PlaybackꢀCapacity
• Maximum number of folder levels (sub folders): 8
Note: If the number of files/folders exceeds the maximum
outlined above, the additional files/folders will be ignored.
USB device and SD card capacity: <32 gigabytes.
DeviceꢀCompatibility
Due to the differences of USB devices and SD cards, some
devices and cards may not be compatible. USB devices and
SD cards must be ‘mass storage class’ and formatted to the
FAT or FAT32 file system in order to ensure compatibility.
SamplingꢀFrequencyꢀRates
8kHz ~ 48kHz
8kHz ~ 48kHz
44.1kHz
MP3
WMA
WAV
TransferꢀBitꢀRates
8kbps ~ 320kbps
32kbps ~ 384kbps
1,411kbps
MP3
WMA
WAV
Note: Some files may not play or be displayed correctly
depending on sampling frequency rates and transfer bit
rates.
10
MXCP44ꢀOPERATION
SDꢀCardꢀ/ꢀUSBꢀOperationꢀ
DisplayingꢀInformation
When a file is accessed, the display will alternate between
track number/elapsed time and available MP3/WMA
information, including file name, song title, artist name,
album name and folder number.
FileꢀIconꢀ
SongꢀTitleꢀIconꢀ
ArtistꢀIconꢀ
This icon will illuminate when the file name is displayed.
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the album name is displayed.
This icon will illuminate when the folder name is displayed.
AlbumꢀIconꢀ
FolderꢀIconꢀ
ꢀ
FolderꢀAccessꢀ Press
to select the previous folder.
to select the next folder.
Press
Notes
Folder access is only available on USB devices and SD
cards that include more than one folder.
Song Title, Artist and Album icons will only be displayed if
the information is included with the MP3/WMA file.
Only MP3 files with filename extension (.mp3) can be
played. Only WMA files with filename extension (.wma) can
be played. Only WAV files with filename extension (.wav)
can be played. Do not attempt to play non-audio MP3/WMA/
WAV files with the .mp3/.wma/.wav extension.
11
MXCP44ꢀOPERATION
SpeakerꢀPreparation/Installation
Please read entire manual before installation.
BeforeꢀYouꢀStart
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Use extreme caution when drilling holes to avoid damaging fuel lines, hydraulic lines
or existing wiring.
• If additional wiring is required, we recommend that you run all wires prior to
mounting your speaker in place.
• Use the highest quality connectors for a reliable installation and to minimize signal
and power loss.
• Use caution before you drill or cut! Be careful not to cut or drill into gas tanks, fuel lines,
hydraulic lines, vacuum lines or electrical wiring.
• Avoid running wires over, near, or through sharp edged surfaces. We suggest you
also use rubber grommets to protect any wires routed through metal.
MountingꢀandꢀInstallation
• Determine where the speakers will be mounted. Ensure an area large enough for
the speaker to mount evenly. Be sure the mounting location is deep enough for the
speaker to fit.
• Using an appropriate tool, cut a 5.13" diameter mounting hole.
• Remove grille from speaker by inserting the release key into the locking tab slots
located at the top and bottom of the grille. Gently apply pressure towards the center
of the grille to release the locking tabs.
• Use the speaker as a template to mark the locations for the mounting screws. Drill
the mounting screw holes with a 1/8" pilot bit. Route speaker wires and connect to
speakers, observing speaker polarity.
• Install speaker into opening using supplied hardware and test for correct operation.
• Align the speaker grille locking tabs and snap grille into place.
RELEASEꢀKEY
12
MXCP44ꢀOPERATION
RadioꢀSpecificationsꢀ
Tuning range: 87.5MHz-107.9MHz
FMꢀTuner
Usable sensitivity: 10dBf
50dB quieting sensitivity: 25dBf
Stereo separation @ 1kHz: >30dB
Frequency response: 30Hz-18kHz
AMꢀTuner
Speakers
Tuning range: 530kHz-1710kHz
Usable sensitivity: <36dB
Frequency response: 80Hz-2kHz
Outside Diameter: 7.13"
Mounting Depth: 2.13"
Mounting Height: .87"
Cut-out Diameter: 5.13"
Frequency Response: 45Hz-15kHz
Sensitivity: 88dBꢀ1W/1M
Impedance: 4ꢀohms
RMS Power:ꢀ20ꢀWattsꢀ@ꢀ1kHz
Peak Power: 100ꢀWattsꢀ@ꢀ1kHz
General
Speaker output impedance: 4~8ꢀohms
Line output voltage: 2ꢀVoltsꢀRMS
Fuse: 10ꢀampꢀAGC
Dimensions: 7"ꢀxꢀ2"ꢀxꢀ5"ꢀ(178ꢀxꢀ50ꢀxꢀ130ꢀmm)
Design and specifications subject to change without notice.
CEA-2006ꢀPowerꢀStandardꢀSpecifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 18 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to noise ratio: 70dBA (reference: 1 watt into 4 ohms)
13
MXCP44ꢀWARRANTY
Troubleshooting
Problem
Cause
Action
Yellow wire not connected or incorrect voltage
Red wire not connected or incorrect voltage
Check connections for proper
voltage (11~16VDC)
Unitꢀwillꢀnotꢀturnꢀonꢀ
(noꢀpower)
Black wire not connected
Fuse blown
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unitꢀhasꢀpowerꢀ
(butꢀnoꢀsound)
One or more speaker wires touching each
other or touching chassis ground
Insulate all bare speaker wires from
each other and chassis ground
Yellow or red wire touching chassis ground
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Check for pinched wire
Unitꢀblowsꢀfuses
Use fuse with correct rating
Device capacity must be less than
32GB.
"SDꢀERR"ꢀorꢀ"USBꢀERR"ꢀ
appearsꢀonꢀdisplay
USB or SD card compatibility issue
File system is incompatible - it must
be FAT or FAT32.
FCCꢀCompliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
14
MXCP44ꢀOPERATION
LimitedꢀOneꢀYearꢀWarranty
This warranty gives you specific legal rights.
Whatꢀtoꢀdo?
You may also have other rights which vary from
state to state.
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a service call.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
Whoꢀisꢀcovered?ꢀThis warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
Whatꢀisꢀcovered?ꢀThis warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment
of the product. Specific license conditions and
copyright notices for the software can be found
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
15
Dual Electronics Corp.
Toll Free: 1-866-382-5476
9AM-5PM EST, Monday-Friday
SD Logo is a trademark of SD-3C, LLC.
Other trademarks and trade names are those of their respective owners.
©2013 Dual Electronics Corp. All rights reserved.
NSA0813-V01
|