Accessory
Application
Publications No.
AII 27936
CD CHANGER
ATTACHMENT KIT
INSTALLATION
INSTRUCTIONS
2002-2005 CIVIC SI
Issue Date
AUG 2004
PARTS LIST
3 EPT seals
CD Changer Attachment Kit (sold separately):
P/N 08B26-S5T-100
4 Cushion tapes
CD changer bracket
8 Cap nuts, 6 mm
4 Washer-screws, 4 x 8 mm
4 Clip-nuts, 6 mm
2 CD changer plates
Template A
4 Stepped bolts, 6 mm
Template B
Left side bracket
Right side bracket
Bus cable
13Wire ties
08B26-S5T-1000-91
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 27936 (0408)
1 of 14
4. Remove the driver's dashboard lower cover.Turn
the lock knob 90° counterclockwise. Gently pull
down on the left side of the cover to release the
two hooks, then pull down on the cover to release
the three retaining tabs. Take care not to damage
the retaining tabs.
6. Remove the shift lever trim:
•
Pull the shift boot down, and remove the shift
knob by turning it counterclockwise.
•
Reach through the shift boot, and gently pull
out on the shift lever trim to release the bottom
of the trim. Lift up on the shift lever trim to
release the five hooks and four clips.
•
Unplug the hazard warning switch connector,
and remove the shift lever trim.
RETAINING
TAB
HAZARDWARNING
SWITCH CONNECTOR
CLIPS (4)
HOOKS (5)
HOOK
RETAINING
TAB
SHIFT LEVER
TRIM
DRIVER'S
DASHBOARD
LOWER COVER
KNOB
(Turn 90° counterclockwise.)
SHIFT
KNOB
5. Remove the driver's dashboard under cover.Turn
the lock knob 90° counterclockwise, and pull down
on the rear of the cover to release the left clip. Pull
the cover out toward you to release the remaining
clip. Take care not to damage the clips.
KNOB (Turn 90°
counterclockwise.)
SHIFT
BOOT
Reach through the shift boot,
and pull the shift lever trim out
toward you.
CLIP
DRIVER'S
DASHBOARD
UNDER COVER
LEFT CLIP
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 27936 (0408)
3 of 14
7. Remove the vehicle harness clip from the center
panel bracket by pushing up on the locking tab on
the clip and pulling the clip out toward you.
9. Remove the dashboard center lower cover, and
disconnect the accessory power socket connector.
Remove the two self-tapping screws from the back
of the front center console.
SELF-TAPPING
SCREW
CENTER
PANEL
BRACKET
Push on the
locking tab.
VEHICLE
CLIP
HARNESS
DASHBOARD CENTER
LOWER COVER
FRONT CENTER
CONSOLE
8. Reach through the glove box area, and loosen the
bolt that secures the center panel. Reach through
the area near the steering wheel, and loosen the
bolt that secures the center panel. Remove the
center panel (eight clips, and unplug the
connectors).
10. Slide the front seat completely forward. Remove
the rear center console (two washer-screws, two
clips, and two retaining tabs). Take care not to
damage the clips and retaining tabs.
BOLTS
(Loosen from the inside.)
RETAINING
TABS (2)
CLIPS (2)
RETAINING
TAB
HOOK
WASHER-
SCREW
CENTER
PANEL
ANTENNA
LEAD
REAR
CENTER
CONSOLE
VEHICLE
CONNECTOR
CLIPS (8)
VEHICLE
CONNECTOR
4 of 14
AII 27936 (0408)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
11. Remove the front center console:
13. Turn over the cargo area mat, and remove the
cargo area floor.
•
•
•
Slide the front seat completely rearward.
CARGO AREA MAT
Open the lid, and take out the console box mat.
Remove the two bolts from the inside of the
pocket.
CARGO
AREA
FLOOR
•
Remove the two clips, then slide the front
center console to the rear to release the four
retaining tabs. Take care not to damage the
retaining tabs.
CONSOLE
BOX MAT
CLIP
RETAINING
TAB
BOLT
14. Remove the cargo area mat (three clips).
CLIPS (3)
CLIP
BOLT
CLIP
Open the lid.
CARGO
AREA
MAT
FRONT CENTER
CONSOLE
12. Open the hatch, and remove the center shelf.
CENTER
SHELF
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 27936 (0408)
5 of 14
15. Remove the rear seat cushion bolt, and remove
the rear seat cushion by lifting the rear of the
cushion to release the hooks and then pulling it
toward you.
20. Remove the left rear seat-back center hinge (one
bolt).
LEFT REAR
SEAT-BACK
CLIP
LEFT REAR
SIDE PANEL
TRIM
FLOOR
CARPET
SEAT-
BACK
CENTER
HINGE
REAR
SEAT
CUSHION
2
1
CLIP
LEFT PIN
BOLT
22 N·m
(16 lb-ft)
HOOK
BOLT
21. Remove the clip from the floor panel behind the
seat-back.
HOOK
22. Release the seat-back pin from the left rear side
panel trim by sliding the seat-back forward while
pushing it toward the outside. Remove the left rear
seat-back.
16. Remove the clip that secures the floor carpet.
17. Fold the right rear seat-back forward. Remove the
hinge cover from the seat-back (three retaining
clips). Take care not to damage the retaining clips.
23. Open the screw lid from the left rear side shelf.
Remove the two self-tapping screws, and separate
the left rear side shelf from the C-pillar trim. Push
down to release the rear clip hooks, then pull the
shelf out toward you to remove it.
BOLT 22 N·m
(16 lb-ft)
RETAINING
TAB
HINGE
COVER
REAR CLIP
HOOKS (4)
CLIP
SELF-TAPPING
SCREW
C-PILLAR
TRIM
SEAT-BACK
CENTER HINGE
REAR SIDE
SHELF
2
1
RIGHT REAR
SEAT-BACK
SEAT BELT
ANCHOR
18. Remove the clip from the floor panel behind the
seat-back.
19. Remove the two bolts that fasten the seat-back
hinge bracket, and move the right rear seat-back
out of the way.
REAR SEAT
BELT
SCREW LID
6 of 14
AII 27936 (0408)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
24. Remove the left rear bulkhead cover:
26. Remove the left rear seat belt lower anchor bolt.
•
•
Remove the clip from the left rear bulkhead
cover. Take care not to damage the clip.
27. Remove the rear trim panel (three clips and two
hooks).
Gently pry the left rear bulkhead cover away
from the left rear side trim panel by inserting
the end of a flat-tip screwdriver wrapped in a
shop towel into the groove of the left rear
bulkhead cover.
CLIP
•
Pry up on the seven retaining tabs, and remove
the left rear bulkhead cover. Take care not to
damage the retaining tabs.
GROOVE
FLAT-TIP
SCREWDRIVER
REAR TRIM
PANEL
HOOK
CLIP
28. Remove the two upper screws and the rear lower
clip from the left rear side trim panel.
UPPER SCREW
LEFT REAR
BULKHEAD
COVER
RETAINING
LEFT REAR SIDE
TAB
TRIM PANEL
25. Remove the clip that fastens the left rear side
trim panel.Take care not to damage the clip.
LEFT REAR SIDE
TRIM PANEL
CLIP
SEAT BELT
LOWER ANCHOR
BOLT
32 N·m (24 lb-ft)
REAR LOWER CLIP
LEFT REAR
SIDE TRIM
PANEL
29. Carefully pull the left rear side trim panel away
from the body without creasing it.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 27936 (0408)
7 of 14
33. Position template B on the air outlet area of the left
rear side trim panel, and tape it in place using
strips of masking tape. Using a pushpin, mark the
trim panel at each of the four marked points on
the template. Remove template B.
30. Get template A from the kit. Tape the template to
the left rear side trim panel in the area shown, and
tape it in place using strips of masking tape. Using
a pushpin, mark the trim panel at each of the five
marked points on the template. Remove
LEFT REAR SIDE
TRIM PANEL
template A.
TEMPLATE B
PUSHPIN
MASKINGTAPE
FRONT
LEFT REAR
SIDE TRIM
PANEL
TEMPLATE A
PUSHPIN
MASKING
LEFT REAR
TAPE
SIDE TRIM
PANEL
Align template A
with the cover
opening of the left
rear side trim panel.
TEMPLATE B
31. While wearing eye protection, drill a 7.5 mm hole
through each of the five marks on the trim panel.
First drill with a 3 mm bit, then finish with a
7.5 mm bit. Wrap electrical tape 10 mm from the
end of the drill bit, or use a drill stop.
34. While wearing eye protection, drill a 10 mm hole
through the left rear side trim panel at each of the
four marks you just made. First drill with a 3 mm
drill bit, then finish with a 10 mm drill bit. Wrap
electrical tape 10 mm from the end of the drill bit,
or use a drill stop.
DRILL (First drill with a
3 mm bit, then finish with
a 7.5 mm bit.)
LEFT REAR
SIDE TRIM
PANEL
10 mm
ELECTRICAL
TAPE
10 mm
DRILL (Enlarge this
hole to 30 mm.)
DRILL
32. Expand the center 7.5 mm hole to 30 mm with a
30 mm Uni-bit.
ELECTRICAL
TAPE
(First drill with a 3 mm drill
bit, then finish with a 10 mm
drill bit.)
8 of 14
AII 27936 (0408)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
35. Slide the four 6 mm clip nuts onto the left rear
side trim panel through the 10 mm holes you just
made.
38. Insert the studs of the two CD changer plates into
the 7.5 mm holes (made in step 31) from the back.
CD CHANGER
6 mm STEPPED
BRACKET
BOLT
6 mm CAP
NUT
6 mm CLIP NUT
6 mm CAP
NUT
LEFT REAR
SIDETRIM PANEL
(AIR OUTLET AREA)
CD CHANGER PLATE
39. Insert the studs of the CD changer plate into the
holes in the CD changer bracket, and install a
6 mm cap nut on the end of each stud. Do not
tighten the 6 mm cap nuts yet.
36. Using scissors, cut 1/4 piece from one of the
EPT seals. Wrap the other two EPT seals and
the 1/4 piece of the EPT seal around the bus
cable in the areas shown.
40. Temporarily secure the top of the CD changer
bracket to the rear side lining with the four 6 mm
stepped bolts, then tighten the four cap nuts and
the four stepped bolts securely.
1/4 PIECE OF EPT SEAL
(Do not discard the remaining
3/4 piece of the EPT seal.)
30 mm HOLE
LEFT REAR SIDE
TRIM PANEL
Installing the CD Changer
170 mm
41. Carefully unpack the CD changer. Remove the
three shipping clips, and discard the shipping
cover. Install an adhesive seal (included with the
CD changer kit) over each of the three clip holes.
Retain the shipping clips in case the unit needs to
be serviced.
SHIPPING CLIPS (3)
BUS CABLE
EPT SEAL
1/4 piece of
one EPT seal
SHIPPING COVER
(Discard.)
(170 mm)
20 mm
(320 mm)
ADHESIVE
SEALS (3)
37. Align the 1/4 piece of the EPT seal you cut in step
36 with the 30 mm hole you drilled in step 32.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 27936 (0408)
9 of 14
42. Visually check the position of the spring adjusting
pins on both sides of the CD changer. If both of the
spring adjusting pins are not in the horizontal (H)
position, move the pins to the horizontal (H)
position by sliding them up with an awl.
45. Secure the CD changer bus cable connector to the
CD changer with the remaining 3/4 piece of the
EPT seal cut in step 36.
EPT SEAL
(Remaining piece of
the EPT seal cut in
step 36)
SPRING ADJUSTING PIN
(H: HORIZONTAL POSITION)
LOCKING
COVER
CD CHANGER
LOCKING
COVER
CD CHANGER BUS
CABLE CONNECTOR
CD CHANGER
46. Connect the bus cable connector to the CD
changer bus cable connector.
47. Insert the studs of the right and left side brackets
installed on the CD changer into the holes in the
CD changer bracket, and install a cap nut on the
end of each stud. Tighten the cap nuts securely.
43 Remove the backing from the "L" and "R" locking
covers, and attach them to the sides of the CD
changer.Align the diagonally opposite holes with
the H and V positions.
CD CHANGER
LEFT SIDE
BRACKET
44. Position the side brackets on the CD changer, and
install the four washer-screws supplied with the CD
Changer Attachment Kit. Note the direction of the
side brackets. The square hole in each of the
brackets should face the rear of the CD changer.
Tighten the washer-screws securely.
RIGHT
SIDE
BRACKET
6 mm CAP
NUT
WASHER-SCREWS (4)
(Supplied with CD
changer attachment kit)
6 mm CAP
NUT
RIGHT SIDE
BRACKET
CD CHANGER
BRACKET
BUS
CABLE
CD CHANGER BUS
CABLE CONNECTOR
CD CHANGER
LEFT SIDE BRACKET
10 of 14
AII 27936 (0408)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
Routing the Bus Cable
50. Route the bus cable from the side panel to the
center of the floor panel along the floor cross
member as shown.
48. From the back of the left rear side trim panel, route
the bus cable as shown. Secure the bus cable to
the fuel fill door opener cable with two wire ties in
the areas shown. Do not secure the bus cable to
the clear washer tube.
CUSHION TAPE
BUS CABLE
WIRE TIE
Do not secure the
bus cable to the
clear washer tube.
FLOOR
PANEL
WIRE TIE
BUS
CABLE
BUS
CABLE
FLOOR
FUEL FILL
DOOR
CARPET
(Turn over.)
OPENER
CABLE
Route the BUS
cable from the
center of the floor
to the front.
FLOOR CROSS
MEMBER
51. Secure the bus cable to the floor panel with two
cushion tapes in the areas shown. Clean the areas
where the cushion tapes will attach with isopropyl
alcohol.
52. Continue routing the bus cable through the center of
the floor panel to the center panel opening.
VEHICLE
HARNESS
CENTER PANEL
OPENING
CUSHION
TAPE
49. Secure the bus cable to the body panel with one
cushion tape in the area shown. Clean the area
where the cushion tape will attach with isopropyl
alcohol.
VEHICLE HARNESS
BUS CABLE
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 27936 (0408)
11 of 14
53. Route the bus cable so that its connector is
about 50 mm farther than the vehicle 20-pin
connector. Secure the bus cable to the vehicle
harness with two wires in the areas shown.
55. Near the parking brake lever, secure the bus cable
to the vehicle harness with three wire ties in the
areas shown.
WIRE TIE
BUS
CABLE
BUS CABLE
CONNECTOR
VEHICLE
HARNESS
VEHICLE 20-PIN
CONNECTOR
WIRE TIE
About 50 mm
56. Loop the excess bus cable at the floor cross
member, and secure it to the vehicle harness with
four wire ties and one cushion tape. Clean the area
where the cushion tape will attach with isopropyl
alcohol.
54. Secure the bus cable to the vehicle harness with
two wire ties in the areas shown.
FLOOR
CROSS
CUSHIONTAPE
WIRE TIE
MEMBER
VEHICLE
HARNESS
BUS CABLE
VEHICLE
HARNESS
WIRE TIE
Loop the bus cable,
and secure it to the
vehicle harness with
four wire ties and one
cushion tape.
BUS CABLE
12 of 14
AII 27936 (0408)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
Installing the Center Panel/Radio Unit
58. While holding the center panel with the radio unit
installed near the center panel opening, plug the
vehicle 20-pin connector, the antenna lead, the
heater control harness connector, and the bus
cable connector into the rear of the radio unit.
57. Check that the vehicle harnesses are not pinched
by the stays.
VEHICLE
HARNESS
ANTENNA
LEAD
CENTER
PANEL
STAY
STAY
VEHICLE
CONNECTOR
BUS CABLE
CONNECTOR
BOLT
(Tighten after
installing the
center panel.)
ANTENNA
LEAD
VEHICLE 20-PIN
CONNECTOR
BUS CABLE
CONNECTOR
59. Reinstall the center panel.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 27936 (0408)
13 of 14
60. Check that all wire harnesses are routed properly
and all connectors are plugged in.
61. Reconnect the negative cable to the battery, and
set the clock.
62. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
63. Check the operation of the CD changer according
to the Owner’s Manual.
64. Put the CD changer Owner’s Manual and the
shipping clips retained in step 41 in the glove
box.
65. Reinstall all removed parts.
66. Do the engine control module (ECM) idle learn
procedure:
•
Make sure all electrical items (A/C, audio, rear
defogger, lights, etc.) are off.
•
Start the engine. Hold the engine speed at
3,000 rpm with no load (in Park or Neutral) until
the radiator fan comes on.
•
Let the engine idle for 5 minutes with the
throttle fully closed and all electrical items off.
NOTE:When the radiator fan comes on, do not
include its running time in the 5 minutes.
14 of 14
AII 27936 (0408)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
|