Clarion VRX746VD User Manual

Owner’s manual & Installation manual  
使用說明書和安裝說明書  
사용 설명 및 설치 설명서  
VRX746VD  
AM/FM DVD VIDEO / VIDEO CD / CD / MP3  
PLAYER / CD CHANGER CONTROLLER WITH 7"  
LC DISPLAY  
帶7英寸液晶顯示器調(AM)/調頻 (FM)DVD  
VIDEO/VIDEO CD/CD/MP3播放機 / CD換片機  
控制器  
7인치 LC 디스플레이 화면의 AM/FM  
DVD 비디오/비디오 CD/CD/MP3 플레  
이어 / CD 체인저 컨트롤러  
R
R
Handling Discs  
2. PRECAUTIONS  
Handling  
Storage  
• New discs may have some roughness around  
the edges. If such discs are used, the player  
may not work or the sound may skip. Use a  
ball-point pen or the like to remove any  
roughness from the edge of the disc.  
• Do not expose discs to direct sunlight or any  
heat source.  
WARNING  
Do not expose discs to excess humidity or dust.  
For your safety, the driver should not watch the TV or operate the controls while driving.  
Please note that watching and operating the TV while driving are prohibited by law in  
some countries. Also, while driving, keep the volume to a level at which external sounds  
can be heard.  
Do not expose discs to direct heat from  
heaters.  
Ball-point pen  
Cleaning  
1. When the inside of the car is very cold and  
the player is used soon after switching on the  
heater, moisture may form on the disc (DVD/  
CD) or the optical parts of the player and  
proper playback may not be possible. If  
moisture forms on the disc (DVD/CD), wipe it  
off with a soft cloth. If moisture forms on the  
optical parts of the player, do not use the  
player for about one hour. The condensation  
will disappear naturally allowing normal  
operation.  
INFORMATION FOR USERS:.  
Roughness  
To remove fingermarks and dust, use a soft  
cloth and wipe in a straight line from the  
center of the disc to the circumference.  
CHANGES OR MODIFICATIONS TO THIS  
PRODUCT NOT APPROVED BY THE MANU-  
FACTURER WILL VOID THE WARRANTY.  
• Do not use any solvents, such as  
commercially available cleaners, anti-static  
spray, or thinner to clean discs.  
• After using special disc cleaner, let the disc  
dry off well before playing it.  
• Never stick labels on the surface of the disc or  
mark the surface with a pencil or pen.  
• Never play a disc with any cellophane tape or  
other glue on it or with peeling off marks. If  
you try to play such a disc, you may not be  
able to get it back out of the DVD player or it  
may damage the DVD player.  
On Discs  
• Exercise a good precaution when loading a  
disc with the panel open.  
• Never turn off the power and remove the unit  
from the car with a disc loaded.  
2. Driving on extremely bumpy roads which  
cause severe vibration may cause the sound  
to skip.  
• Do not use discs that have large scratches,  
are misshapen, cracked, etc. Use of such  
discs may cause misoperation or damage.  
3. This unit uses a precision mechanism. Even  
in the event that trouble arises, never open  
the case, disassemble the unit, or lubricate  
the rotating parts.  
CAUTION  
To remove a disc from its storage case, press  
down on the center of the case and lift the  
disc out, holding it carefully by the edges.  
With the screen open, a driver may not see the  
disc insertion slot. For your safety, insert a disc  
with the screen closed.  
• Do not use commercially available disc  
protection sheets or discs equipped with  
stabilizers, etc. These may damage the disc  
or cause breakdown of the internal  
mechanism.  
Even when the screen is closed, however, the  
recessed disc slot may be difficult for a driver  
to see, care is needed whenever inserting  
discs.  
4. TV broadcast reception  
When receiving the TV broadcasts, the  
strength of the signals changes since the car  
is moving, so in some cases it may not be  
possible to receive clear pictures.  
• TV signals are strongly linear, so reception is  
affected by buildings, mountains and other  
obstacles.  
No/Non  
• Such external factors such as electric train  
lines, a high voltage lines, and signal devices  
may disturb the picture or cause noise.  
If the reception is poor, switch to a station  
with good reception.  
Be sure to unfold and read the next page.  
請務必打開并閱讀下一頁。  
이 페이지를 펼친 채로 다음 페이지를 읽어 보십시오.  
VRX746VD  
3
VRX746VD  
4
4. NOMENCLATURE  
3. CONTROLS / 控制部分 / 컨트롤  
Names of Buttons  
Note:  
[
]
[
]
[
]
VOL  
BAND  
FUNC  
• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold).  
[VOL] button  
[s] button  
[
FRONT  
]
OPEN  
[
]
Use this button to increase/decrease the  
Press this button to enter the play pause  
mode in the DVD video mode and changer  
mode. Press the button again to resume  
playback.  
SENSOR  
volume.  
[
]
[
]
ISR  
DISP  
[DISP] button  
Use this button to switch the indications such  
as play status on the information panel.  
Press and hold this button for 1 second or  
longer to mute the sound in the DVD video  
mode and changer mode.  
Press this button to mute the sound in the  
radio/TV/VISUAL mode.  
[
]
[
]
[
]
OPEN  
s
[OPEN] button  
Use this button to open/close the liquid crystal  
panel.  
DIRECT  
[
]
ADJ  
Press and hold this button for about 2  
seconds or longer so that the liquid crystal  
panel is positioned horizontally when the  
liquid crystal panel is open (Air Conditioner  
Operation mode).  
[BAND] button  
Press this button to switch the receiving  
bands for radio/TV mode, etc. Press and hold  
this button for 1 second or longer to switch the  
SEEK/MANUAL tuning modes.  
With the Front panel open / 前面板開啟時 / 전면 패널이 열린 상태에서  
Use this button to move to the first track on a  
disc in the DVD video mode.  
Use this button to switch to the next disc in  
the changer mode.  
[FRONT OPEN] button  
Use this button to open the Front panel.  
[SENSOR]  
Remote control infrared sensor.  
[FUNC] button  
Press this button to turn on the power. Press  
and hold this button for 1 second or longer to  
turn off the power.  
Press this button to switch the modes such as  
radio.  
[ISR] button  
Use this button to enter the ISR (Instant  
station recall) standby mode.  
Press and hold this button for 2 seconds or  
longer to store the current station into ISR  
memory in the radio mode.  
[ADJ] button  
Shows the ADJUST MODE menu to change  
the settings when the liquid crystal panel is  
open.  
[DIRECT] button  
Use this button to select a preset channel in  
the radio/TV mode.  
Press and hold this button for 1 second or  
longer, the liquid crystal panel can be  
switched to a composite screen to lock the  
monitor. (To enable this function, go to the  
GENERAL menu (within the ADJUST MODE  
menu), and use the [CONNECT] key to select  
NAVIor OTHERS).  
Use this button to select a disc in the changer  
mode.  
Press and hold one of the [DIRECT] button for  
2 seconds or longer to store the current  
station into preset memory.  
[a], [d] buttons  
Use this button to tune to a station in the  
radio/TV mode.  
Use this button to select a track in the CD,  
Video CD, MP3 and CD changer mode.  
Use this button to select a chapter in the DVD  
video and DVD changer mode.  
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.  
注意﹕在閱讀每一章時,請務必打開本頁,并參照本頁的前視圖。  
참고:이 페이지를 펼쳐두고, 각 장을 읽을때 전면 그림을 참조하도록 하십시오.  
5
VRX746VD  
6
VRX746VD  
When the Front panel open  
[TILT] button  
Use this button to adjust the angle of the liquid  
crystal panel in 5 steps when the liquid crystal  
panel is open.  
When the panel is closed, holding this button  
depressed for 2 seconds or longer will enable  
the panel calibration function.  
[Q] button  
Use this button to eject a disc.  
VRX746VD  
7
5. DISPLAY  
The Color LCD Display and the Information Panel on the main unit show the following displays,  
providing information about the mode and functions operated.  
Information Panel  
Operation status indication  
The frequency, play time,  
clock, etc. are displayed.  
: Manual indication  
: Stereo indication  
: MAGNA BASS-EX indication  
: ALL indication  
: Scan indication  
: Repeat indication  
: Random indication  
: Preset channel indication  
Disc number indication  
The disc numbers corresponding to  
the discs in the DVD or CD changer  
light.  
8
VRX746VD  
Color LCD Display  
Mode name  
Radio mode  
: FM1 98.10MHz Pch 1 (band/frequency/preset No.)  
DVD changer mode: D2 T02 C002 01:08:20  
(disc No./title No./chapter No./ playback time)  
DVD video mode : T01 C003 00:08:20 (title No./chapter No./playback time)  
Video CD mode : T01 00:01:18 (track No./playback time)  
MP-3 mode  
: F001 T001 00:04:07 (folderNo./track No./playback time)  
CD mode  
: T 02 04 : 07 (track No./playback time)  
CD changer mode : D2 T02 00 : 45 (disc No./track No./playback time)  
TV mode  
: TV1 28CH Pch 1 (band/channel/preset No.)  
VISUAL mode  
: No display  
Clock time  
Displays control keys corresponding to  
play mode.  
: Seek/Manual indication  
: Stereo indication  
MANU  
ST  
Example for radio mode:  
SRCH: Input numbers to tune specific  
broadcast frequencies.  
BAND: Switch reception band  
LIST : Display preset memory station  
list.  
: MAGNA BASS-EX indication  
M•B EX  
When the 5.1ch surround decoder (DVH940) is  
connected, the signal format of the digital input  
signal (for example, “Dolby D 3/2+LFE”) is  
displayed.  
,
:
Tune stations  
Radio/TV mode : USER WEST COAST (user title)  
CD mode/CD changer mode : USER SHINE (user title)  
CD TEXT in CD mode/CD changer mode  
:
:
:
DISC SHINE (disc title)  
TRACK Time has come (track title)  
ARTIST Time has come (artist)  
VRX746VD  
9
OUTLINE OF BUTTON AND TOUCHKEY  
OPERATION  
6.  
2  
1  
Engine ON  
position  
System check  
The CeNET format utilized on this unit is  
provided with a system check function. The  
operation panel’s system check menu is  
displayed under the following conditions:  
• When power is first turned on after initial  
installation.  
• When an external device is connected or  
disconnected.  
• When batteries are changed or otherwise  
when power is disconnected.  
• When reset button is pressed.  
In addition to the above conditions, when the  
liquid crystal panel is open and the “PUSH  
POWER KEY” message is displayed, the  
system check screen can be displayed by  
pressing the [FUNC] button.  
10  
VRX746VD  
(Radio mode screen)  
(Next page)  
(LIST screen)  
3  
(KEY PAD screen)  
5  
(Title input screen)  
4  
1
0
7
9
0
ENT  
6  
7  
Notes:  
1: The operation button is [OPEN] button in the  
description of operation per mode.  
2: External equipment not connected with  
CeNET is not displayed.  
3: The operation key is [SRCH] key in the  
description of operation per mode.  
4: This shows a KEY PAD selection example in  
the radio mode when 107.90 MHz is selected.  
5: Touch the [RTN] key to return to the  
previous screen.  
6: Touch the [z] key to go to the next menu.  
Touch the [w] key to return to the previous  
menu.  
7: Touch the [ESC] key to return to the main  
screen.  
VRX746VD  
11  
(Radio mode screen)  
(FUNCTION menu)  
8  
9  
11 (DVD mode screen)  
10  
(SUB menu)  
Notes:  
8: The FUNCTION menu screen displays  
icons for components connected to the  
main unit. The icons serve as touch keys  
for selecting play modes.  
P.TIME  
9: Pressing the [FUNC] button changes to the  
12  
following play modes.  
10: Screen during DVD mode when automobile  
is moving.  
11: When displaying images in DVD mode,  
touching the screen surface will cause the  
menu screen to be displayed.  
12: When the playback status has been  
displayed by pressing the [P.TIME] key, the  
display can be canceled by touching the  
screen.  
12  
VRX746VD  
(Next page)  
(ADJUST MODE menu)  
(DVD SETUP menu)  
(MONITOR menu)  
MONI ADJ  
PARENRTAL LEBEL  
VRX746VD  
13  
When a 5.1 ch Surround  
Decorder is connected  
(ADJUST MODE menu)  
(AUDIO MODE menu)  
(GENERAL menu)  
BAL/FAD  
CLOCK  
14  
VRX746VD  
(AUDIO EXT. menu)  
(AUDIO MODE menu)  
SPEAKER SEL  
STATUS  
SUB WOOFER  
DSF  
VRX746VD  
15  
7. REMOTE CONTROL  
Remote control unit  
Signal transmitter  
Operating range: 30˚ in all directions  
[
]
]
BAND  
[
[
]
MUTE  
[
]
FUNC  
VOLUME  
[
[
]
P.TIME  
[
]
0-9  
]
DISP  
[
]
]
]
DISC SEL  
[
],[  
[
[
]
SEARCH MODE  
[
]
MENU  
RTN  
[
[
]
DVD TITLE  
[
]
]
SET UP  
],[  
]
[
ENT  
[
]
ISR  
[
[
]
2-ZONE  
[
]
[
]
PBC  
SCN  
]
[
]
RDM  
RPT  
[
]
]
[
[
]
AUDIO  
SLOW  
]
[
ANGLE  
SUB TITLE  
Inserting the Batteries  
1.Turn the remote control unit over, then slide the  
rear cover in the direction of the arrow.  
AA (SUM-3, IECR-6/1.5V)  
Batteries  
2.Insert the AA (SUM-3, IECR-6/1.5V) batteries  
that came with the remote control unit facing in  
the directions shown in the figure, then close the  
rear cover.  
Notes:  
Using batteries improperly can cause them to  
explode. Take note of the following points:  
Rear cover  
• When replacing batteries, replace both batteries  
with new ones.  
• Do not short-circuit, disassemble or heat batteries.  
• Do not dispose of batteries into fire or flames.  
• Dispose of spent batteries properly.  
Rear side  
16  
VRX746VD  
Functions of Remote Control Unit Buttons  
GShared modes  
GDVD player mode  
[FUNC] button  
[BAND] button  
Press to return to the first chapter in DVD  
video mode.  
Press to return to the first track in CD/MP-3  
mode or video CD mode with the PBC  
function turned off.  
Press and hold this button for 1 second or  
longer to turn on or off the power. Power on/  
off, switches among radio, TV, etc.  
[VOLUME] button  
Increases and decreases volume.  
[P.TIME] button  
Press to turn on and off the playtime display in  
the DVD video and video CD mode.  
[MUTE] button  
Turns mute on and off.  
[ISR] button  
[
] button  
Recall ISR radio station in memory.  
Press and hold for 2 seconds or longer: Store  
current station into ISR memory (radio mode  
only).  
Press to play or pause video and audio  
media.  
Press and hold this button for 1 second or  
longer to stop video playback in DVD video.  
[DISP] button  
Press to change display on information panel  
(MAIN © SUB © Clock Time)  
[0 - 9] button  
Press to enter DVD video chapters in the KEY  
PAD screen.  
Press to set the track number of the Video CD  
with the PBC function turned off, CD track  
number or MP-3 track number in the KEY  
PAD screen.  
[2-ZONE] button  
This button is not available.  
GRadio/TV mode  
[SEARCH MODE] button  
Press to display the KEY PAD operation  
screen.  
[BAND] button  
Switches reception band.  
[RTN] button  
[0 - 9] button  
Press to switch the screen display while the  
MENU screen is being displayed. However, it  
may occur that this button operation dose not  
work on some discs.  
Use in the KEY PAD operation screen to set  
the radio frequency and TV channels (cannot  
be used when TV tuner TTX7504z is  
connected).  
[MENU] button  
Press to display menu stored on video disc.  
[DISC SEL] button  
Press to display the P.CH SELECT screen.  
[SET UP] button  
[SEARCH MODE] button  
Press to display the KEY PAD operation  
screen.  
Press to display the menu for setting audio  
features during DVD video playback.  
Press to show the DVD SETUP menu.  
If you want to select a menu after the SETUP  
menu is displayed, touch the operation keys on  
the menu screen.  
[ENT] button  
Press to confirm numerics entered in the KEY  
PAD operation screen.  
[DVD TITLE] button  
[a], [d] buttons  
Press to display the title screen on DVD video  
discs. Some discs do not display the title  
screen.  
Press to select the next higher or lower preset  
channel in radio and TV mode.  
[SCAN] button  
Press to perform preset scans in the radio and  
TV modes.  
Press and hold for 2 seconds or longer to  
perform the auto store operation in the radio  
and TV modes.  
VRX746VD  
17  
Functions of Remote Control Unit Buttons  
[w], [z], [Å], [Î] buttons  
Press to select menus and other items during  
DVD video/MP-3 playback.  
GCD changer mode  
[BAND] button  
Press to switch discs.  
[ENT] button  
Press to confirm numerics entered in the KEY  
PAD operation screen.  
[DISC SEL] button  
Used to change the disc.  
[a], [d] buttons  
[
] button  
Press to select the next higher or lower  
chapter number in DVD video mode.  
Press to select the next higher or lower track  
numbers in CD/MP-3 mode or video CD mode  
with the PBC function turned off.  
Hold down to perform fast-forward and fast-  
backward.  
Press to play and pause the media.  
[0 - 9] buttons  
Press to enter track numbers in the KEY PAD  
screen.  
[SEARCH MODE] button  
Press to display the KEY PAD operation  
screen.  
[SCAN] button  
Press to perform chapter scans in DVD video  
mode and track scans in CD mode. Press to  
perform track scan and hold down to perform  
folder in MP-3 mode.  
[a], [d] buttons  
Press to select the next higher or lower  
playback track.  
Hold down to perform fast-forward and fast-  
backward.  
[RPT] button  
Press to perform chapter repeat in DVD video  
mode and track repeat in CD mode. In the  
MP-3 mode, press to perform track repeat and  
hold down to perform folder repeat.  
[SCAN] button  
Press to perform track scan and hold down to  
perform disc scan.  
[RPT] button  
Press to perform track repeat and hold down  
to perform disc repeat.  
[RDM] button  
Press to play tracks at random in CD mode. In  
the MP-3 mode, press to play tracks at  
random and hold down to play folders at  
random.  
[RDM] button  
Press to play tracks at random and hold down  
to play folders at random.  
[PBC] button  
Press to turn on and off the PBC function in  
video CD mode.  
GDVD changer mode  
[AUDIO] button  
Press to switch on the AUDIO function in DVD  
video and video CD modes.  
[BAND] button  
Press to switch discs.  
[DISC SEL] button  
Used to change the disc.  
[SUB TITLE] button  
Press to display subtitles in DVD video mode.  
* Other button operations in this mode are  
the same as those in DVD player mode.  
[ANGLE] button  
Press to turn the ANGLE function on and off in  
DVD video mode. (This button is available  
only on multiple angles DVDs.)  
[SLOW] button  
Press to perform slow playback in DVD video  
or video CD mode.  
18  
VRX746VD  
8. DCP  
The control panel can be detached to prevent  
theft. When detaching the control panel, store it  
in the DCP (DETACHABLE CONTROL PANEL)  
case to prevent scratches.  
CAUTION  
Be sure to close the HOLD FLAP for safety  
when removing the DCP.  
We recommend taking the DCP with you when  
leaving the car.  
Attaching the DCP  
1. Insert the right side of the DCP into the main  
unit.  
Removing the DCP  
1. Press the [FUNC] button for 1 second or  
longer to turn off the power.  
2. Insert the left side of the DCP into the main  
unit.  
[
]
FUNC button  
[
]
DCP  
FRONT OPEN button  
CAUTION  
2. Deeply push in [FRONT OPEN] button to  
unlock the front panel.  
If the front panel does not open fully, gently  
open it with your hand.  
• The DCP can easily be damaged by  
shocks. After removing it, be careful not to  
drop it or subject it to strong shocks.  
• If the front panel is kept open, the DCP  
may drop due to vibration of the car.  
This results in damage to the DCP. So  
close the front panel or remove the DCP to  
store into the case.  
• The connector connecting the source unit  
and the DCP is an extremely important  
part. Be careful not to damage it by  
pressing on it with fingernails,  
screwdrivers, etc.  
DCP  
3. Pull the DCP toward you and remove it.  
4. Close the HOLD FLAP.  
• Remote control unit cannot be used when  
front panel is open.  
Note:  
If the DCP is dirty, wipe off the dirt with a soft dry  
cloth only.  
HOLD FLAP  
VRX746VD  
19  
9. CAUTIONS ON HANDLING  
Liquid crystal panel/Generalities  
For a longer service life, be sure to read the following cautions.  
Be sure to store the liquid crystal panel inside  
the main unit when parking the car outdoors  
for long period of time. The liquid crystal panel  
will operate properly in a temperature range of  
0 to 60˚C.  
Do not place anything on the display when the  
panel is tilted.  
The remote controller may not work if the  
remote control sensor is exposed to direct  
sunlight.  
Dont allow any liquids on the set from drinks,  
umbrellas etc. Doing so may damage the  
internal circuitry.  
In extremely cold weather, the display  
movement may slow down and the display  
may darken, but this is not a malfunction. The  
display will work normally when the  
temperature increases.  
Do not disassemble or modify the set in any  
way. Doing so may result in damage.  
Do not draw the liquid crystal panel out and  
use it as a tray. Also, subjecting the liquid  
crystal panel to shocks may result in  
Small black and shiny spots inside the liquid  
crystal panel are normal for LCD products.  
The liquid crystal panel may stop temporarily  
when it opens or closes, when the engine  
stops or when it is cold.  
breakage, deformation or other damage.  
Do not let cigarettes burn the display. Doing  
so may damage or deform the cabinet.  
The touchkeys on the display operate when  
slightly touched. Do not press the touchkey  
screen with much force.  
If a problem should occur, have the set  
inspected at your store of purchase.  
Do not insert objects or poke in the space  
between the liquid crystal panel and the main  
unit when the panel is tilted.  
Do not push the case surrounding the  
touchkey panel with much force. This may  
cause malfunctioning of the touchkeys.  
Cleaning  
Cleaning the cabinet  
Cleaning the liquid crystal panel  
Use a soft, dry cloth and gently wipe off the  
dirt. For tough dirt, apply some neutral  
detergent diluted in water to a soft cloth, wipe  
off the dirt gently, then wipe again with a dry  
cloth.  
The liquid crystal panel tends to collect dust,  
so wipe it off occasionally with a soft cloth.  
The surface is easily scratched, so do not rub  
it with hard objects.  
Do not use benzene, thinner, car cleaner, etc.,  
as these substances may damage the cabinet  
or cause the paint to peel. Also, leaving  
rubber or plastic products in contact with the  
cabinet for long periods of time may cause  
stains.  
20  
VRX746VD  
10. DVD VIDEO SYSTEM  
DVD video is a high-quality digital video source  
Multi-story function  
that provides crisp and clear images. One 12  
cm disc contains either one film or four hours of  
music.  
When a DVD video contains more than one  
story for a film, you can select the story you  
wish to enjoy. The operation procedures vary  
with the disc; observe the instructions for  
selecting a story provided during playback.  
DVD Video Features  
This unit provides the following functions in  
addition to the high image quality and sound  
quality of DVD video.  
Dolby digital  
Dolby digital enables up to 5.1 independent  
multi-channel audio reproduction, the same type  
of surround system that is also used in movie  
theaters.  
Notes:  
The functions described in the section,  
Features, for example, the recorded language,  
subtitles, angles, etc. differ with the DVD video  
disc. Refer to the instructions provided with the  
DVD video.  
Some disc functions may operate differently than  
described in this manual.  
DTS  
DTS (Digital Theater System) is a digital sound  
compression technique developed by Digital  
Theater Systems, Inc.  
This low sound compression format delivers a  
large amount of data and makes it possible to  
reproduce a high quality sound.  
Multi-sound function  
DVD video can store up to 8 languages for one  
film; select the language of your preference.  
The languages stored on the disc are  
indicated by the icon shown below.  
Menu screens  
Menus can be called up during DVD video  
playback to perform menu setting.  
Example showing menu display  
Multi-angle function  
A DVD video that is filmed from multiple angles  
allows you to select the angle of choice.  
The number of recorded angles are indicated  
by the icon shown below.  
Subpicture (subtitles) function  
A DVD video can record subtitles for up to 32  
languages and you can select the language of  
the subtitles you wish to see.  
The number of recorded subtitle languages  
are indicated by the icon shown below.  
VRX746VD  
21  
TV color system  
Discs  
This DVD player plays NTSC or PAL discs only  
and cannot be used for playback of SECAM  
discs.  
Playable discs  
This DVD video player can play the following  
discs.  
About MP3 playback  
This unit can play back CD-R/CD-RW discs on  
which MP3 music data have been recorded.  
Playable discs  
DVD video discs  
Audio CDs  
video CDs  
CD TEXT  
For a detailed information, see the page entitled  
Listening to an MP3.  
About the registered marks etc.  
This product incorporates copyright protection  
technology that is protected by method claims  
of certain U.S. patents and other intellectual  
property rights owned by Macrovision  
Corporation and other rights owners. Use of  
this copyright protection tecnology must be  
authorized by Macrovision Corporation, and is  
intended for home and other limited viewing  
uses only unless otherwise authorized by  
Macrovision Corporation. Reverse  
About CD Extra discs  
A CD Extra disc is a disc in which a total of two  
sessions have been recorded. The first session  
is Audio session and the sedond session Data  
sessioin.  
Your personally-created CDs with more than 2  
data sessions recorded cannot be played on  
this DVD video player.  
engineering or disassembly is prohibited.  
Manufactured under license from Dolby  
Laboratories.  
Discs that cannot be played back  
This DVD video player cannot play back DVD-  
R, DVD-RAM, DVD-ROM, CD-ROM, Photo  
CDs.  
Dolby, Pro Logic, and the double-D  
symbol are trademarks of Dolby Laboratories.  
Some CDs recorded in CD-R/CD-RW mode  
may not be usable. (Cause: disc  
characteristics, cracks, dust/dirt, dust/dirt on  
players lens, etc.)  
• “DTSand DTS Digital Outare trademarks  
of Digital Theater Systems, Inc.  
Note on region numbers  
The DVD video system assigns a region  
number to DVD video players and DVD discs by  
sales area.  
The DVD video region number is marked on the  
disc jacket as shown below.  
3
4
ALL  
3
6
22  
VRX746VD  
11. OPERATIONS  
Note: Be sure to read this chapter referring to the front diagrams  
of chapter 3. CONTROLSon page 5 (unfold).  
Basic Operations  
Adjusting the volume  
CAUTION  
1. Operate the [VOL] button in the direction of  
When the unit is turned on, starting and stopping  
the engine with its volume raised to the maximum  
level may harm your hearings. Be careful about  
adjusting the volume.  
the + (up) or (down) to adjust the volume;  
+ : Increases the volume.  
: Decreases the volume.  
The volume level indicated in the display is in a  
range from 0 (minimum) to 33 (maximum).  
Note:  
Use this unit after starting the engine.  
Engine ON  
position  
CAUTION  
While driving, keep the volume at a level at which  
external sounds can be heard.  
Turning on and off the power  
Note:  
Switching the display  
When the panel is closed:  
Be careful about using this unit for a long time  
without running the engine. If you drain the cars  
battery too far, you may not be able to start the  
engine and this can reduce the service life of the  
battery.  
1. Press the [DISP] button to select the desired  
display.  
Each time you press the [DISP] button, the  
display switches in the following order:  
1. Press the [FUNC] button.  
2. The illumination and display on the unit light  
up. The unit automatically remembers its last  
operation mode and will automatically switch  
to display that mode.  
MAIN Display  
3. Press and hold the [FUNC] button for 1  
second or longer to turn off the power for the  
unit.  
SUB Display  
Note:  
About the SYSTEM CHECK”  
The confirmation of connected equipment must  
be performed for this unit only when the wiring  
connection is complete and power is turned on to  
the unit first. When the power is supplied, PUSH  
PWRappear in the display. Press the [FUNC]  
button, the system check starts inside the unit.  
When COMPLETEand PUSH PWRappear  
alternately, press once again the [FUNC] button.  
Clock Time Display  
MAIN Display  
Notes:  
Once selected, the preferred display becomes the  
default display. When a function adjustment such  
as volume is made, the display momentarily  
switches to that functions display, then returns  
back to the preferred display several seconds  
after the adjustment.  
If a title has been input, it is shown in the SUB  
display. If no title has been input, NO TITLE”  
appears in the display. To input a title, refer to the  
subsection Entering titlesin Other Functions”  
section.  
For CD and TV, some special characters of the  
title will not be displayed on the Information Panel  
of the DCP. In this case, those characters will only  
be left blank.  
Selecting a mode  
1. Press the [FUNC] button to change the mode  
of operation.  
2. Each time you press the [FUNC] button, the  
mode of operation changes in the following  
order:  
Radio mode DVD mode CD changer  
mode DVD changer mode TV mode ➜  
VISUAL mode Radio mode...  
External equipment not connected with  
CeNET is not selected.  
SUB displays do not appear when panel is open.  
VRX746VD  
23  
Basic Operations  
Opening and turning the liquid  
crystal panel  
Panel calibration function  
The liquid crystal panels maximum angle of  
inclination can be adjusted to match the  
installation configuration within the automobile.  
WARNING  
To prevent the battery from going dead,  
operate this unit with the engine running,  
if possible.  
Perform this with the panel in its closed position.  
1. Deeply push in [FRONT OPEN] button to  
unlock the front panel.  
When the liquid crystal panel is operat-  
ing, be careful not to get your hand or fin-  
ger caught between the panel and main  
unit or the instrument panel of the car.  
2. Press and hold the [TILT] button for 2  
seconds or longer, until the electronic beep is  
heard.  
3. The beep will sound twice, and the panel will  
rise and the calibration function will begin.  
Do not move the liquid crystal panel by  
hand.  
4. After completion of the calibration, the panel  
will close automatically.  
If the panel does not strike the instrument  
panel or other parts of the car during  
calibration, the maximum inclination will be  
110°.  
Standing up the liquid crystal panel  
1. Press the [OPEN] button and the liquid  
crystal panel comes out and stand up  
automatically.  
If the panel strikes a car part during calibration  
within a range of 70° inclination, the maximum  
downward inclination will be 70°.  
Adjusting the angle of the liquid  
crystal panel  
The angle of the liquid crystal panel can be  
adjusted depending on the mounting angle of  
the unit or light coming into the car.  
GTo adjust the angle  
1. Every time the [TILT] button is pressed, the  
liquid crystal panel tilts forward or backward.  
The adjusted angle is stored in memory.  
While the liquid crystal panel is opening or  
closing, the LED of the [FUNC] button blinks.  
Adjustment is possible within the range 70° to  
110°, or within the range set by panel  
calibration.  
Notes:  
If the liquid crystal panel stops in the middle of its  
operation, press the [OPEN] button to house the  
panel and press the button again to stand it up.  
The unit enters the same display mode as the  
display was turned off the last time.  
There are 5 adjustable angle available.  
MAX110  
˚
If the liquid crystal panel stops at any point less  
than 70°, the electronic beep will sound.  
70˚  
24  
VRX746VD  
Basic Operations  
Housing the liquid crystal panel  
1. Press the [OPEN] button and the liquid  
crystal panel is housed automatically.  
Adjusting the AUDIO  
Note:  
When the separately-sold 5.1 ch Surround  
Decoder (DVH940) is used, the bass and treble  
tone adjustments cannot be made. To adjust the  
tone, refer to the section 5-1 ch Surround  
Decorder Operations.  
Note:  
When leaving this unit unused for a long period of  
time or leaving your car, be sure to house the  
liquid crystal panel into the main unit.  
Turning the liquid crystal panel  
horizontal (Air conditioner  
operation mode)  
When the way the liquid crystal panel is  
mounted hinders the operation of the air  
conditioner, the position of the panel can be  
turned horizontal temporarily.  
Adjusting the balance/fader  
1. Press the [ADJ] button, then touch the  
[AUDIO] key.  
2. Touch the [BAL/FAD] key.  
3. Touch the [w] or [z] key to adjust to the  
fader level.  
The factory default setting is 0. (Adjustment  
range: front 13 to rear 13)  
1. Press and hold the [OPEN] button when the  
liquid crystal panel is upright, and release the  
button when a beep is heard.  
[w] key: Emphasized the sound from the  
front speakers.  
2. The liquid crystal panel turns horizontal.  
[z] key: Emphasized the sound from the  
Press the [OPEN] button again when the  
liquid crystal panel is in the horizontal position,  
and the panel returns to the original position.  
rear speakers.  
4. Touch the [Å] or [Î] key to adjust to the  
balance level.  
The unit can also be set so that the panel  
returns to its original angle after a set time in  
the horizontal position (See P. 29).  
The factory default setting is 0. (Adjustment  
range: left 12 to right 12)  
[Å] key : Emphasized the sound from the left  
speakers.  
Mute  
[Î] key : Emphasized the sound from the  
1. When in the radio, VISUAL or TV mode,  
each time you press the [MUTE] button,  
mute is turned on and off. MUTEappears  
when mute is turned on.  
right speakers.  
5. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
2. In modes other than radio, VISUAL, or TV,  
enable the MUTE function by holding the  
[MUTE] button depressed for 1 second or  
longer.  
Adjusting the BASS  
The bass gain, bass frequency (center frequency)  
and bass Q can be adjusted as follows.  
1. Press the [ADJ] button, then touch the  
[AUDIO] key.  
Regarding the menu screens [RTN]  
and [ESC] keys  
[RTN]: Touch the [RTN] key to return to the  
previous screen.  
2. Touch the [BASS] key.  
3. When the bass type selection screen is  
displayed, touch the key for the desirable  
type to select it.  
[ESC]: Touch the [ESC] key to return to the  
main screen.  
4. Touch the [w] or [z] key to adjust to  
desirable level.  
In the ADJUST MODE, pressing the [ADJ]  
button will also cause a return to the main  
screen.  
GAIN : 6 to 8 (The factory default setting  
is 0)  
FREQ. : 50Hz/80Hz/120Hz (The factory  
In cases where this kind of multiple key  
response is supported, the following kind of  
notation will be used:  
default setting is 50)  
Q
: 1/1.25/1.5/2 (The factory default  
setting is 1)  
Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
5. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
VRX746VD  
25  
Basic Operations  
3. Touch the [w] or [z] key to adjust to  
Adjusting the MID  
The MID gain, MID frequency (center  
frequency) and MID Q can be adjusted as  
follows.  
desirable level.  
The factory default setting is 0. (Setting  
range: 6 to 6)  
4. Touch the [RTN] key, [ESC] key, or press the  
1. Press the [ADJ] button, then touch the  
[ADJ] button.  
[AUDIO] key.  
2. Touch the [MID] key.  
Turning on/off the MAGNA BASS  
EXTEND  
The MAGNA BASS EXTEND does not adjust  
the low sound area like the normal sound  
adjustment function, but emphasizes the deep  
bass sound area to provide you with a dynamic  
sound.  
3. When the bass type selection screen is  
displayed, touch the key for the desirable  
type to select it.  
4. Touch the [w] or [z] key to adjust to  
desirable level.  
GAIN : 6 to 6 (The factory default setting  
is 0)  
1. Press the [ADJ] button, then touch the  
FREQ. : 700Hz/1kHz/2kHz (The factory  
[AUDIO] key.  
default setting is 1k)  
2. Thouch the [MB EX] key.  
Q
: 1.5/2 (The factory default setting is  
2)  
Each time you touch the [MB EX] key, you  
can switch between ONand OFF. When  
the MAGNA BASS EX effect is turned on,  
MB EXlights in the display.  
5. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
3. Touch the [RTN] key, [ESC] key, or press the  
Adjusting the TREBLE  
The treble gain and treble frequency (center  
frequency) can be adjusted as follows.  
[ADJ] button.  
Adjusting the MONITOR  
1. Press the [ADJ] button, then touch the  
[AUDIO] key.  
Adjusting the brightness and tone  
of color  
2. Touch the [TREBLE] key.  
3. When the bass type selection screen is  
displayed, touch the key for the desirable  
type to select it.  
Notes:  
This function is not available when the display is  
stored.  
4. Touch the [w] or [z] key to adjust to  
The HUE setting can be adjusted only when the  
NTSC mode is selected.  
desirable level.  
Switch to the VISUAL/DVD player(DVD video or  
video CD)/DVD changer/TV mode you see.  
1. Press the [ADJ] button to switch to the  
GAIN : 6 to 6 (The factory default setting  
is 0)  
FREQ. : 8kHz/12kHz (The Factory default  
ADJUST MODE menu.  
setting is 12K)  
2. Touch the [MONITOR] key.  
5. Touch the [RTN] key, [ESC] key, or press the  
3. Touch the [MONI ADJ] key to display  
[BRIGHT], [HUE] and [COLOR] key. Touch  
the [BRIGHT], [HUE] and [COLOR] key to  
adjust BRIGHT, HUE and COLOR.  
[ADJ] button.  
Adjusting the non fader output  
volume  
G BRIGHT:  
You can adjust the volume output from the units  
non fader output terminal.  
Adjust the brightness of the display.  
G HUE:  
1. Press the [ADJ] button, then touch the  
Adjust the tone of color (red is emphasized  
or green is emphasized)  
This operation is available only when the car  
[AUDIO] key.  
2. Touch the [NON FADER VOL] key.  
is stopped and the parking brake is applied.  
26  
VRX746VD  
Basic Operations  
G COLOR:  
Switching the VTR system between  
Adjust the color saturation.  
This operation is available only when the car  
is stopped and the parking brake is applied.  
NTSC and PAL  
This function is enabled only when the panel is  
open.  
4. Operate the touch key to adjust a level.  
The factory default setting is NTSCfor the  
Korea-market model, and PALfor all others.  
G BRIGHT:  
Switch to the VISUAL/VTR in TV mode you use.  
[Î] Press to make image brighter  
1. Press the [ADJ] button to switch to the  
[Å] Press to make image dimmer  
ADJUST MODE menu.  
G HUE:  
2. Touch the [MONITOR] key.  
[Î] Press to increase green  
[Å] Press to increase red  
G COLOR:  
3. Touch the [NTSC/PAL] key to select NTSC”  
or PAL.  
4. Touch the [RTN] key, [ESC] key, or press the  
[Î] Press to increase color depth  
[Å] Press to decrease color depth  
[ADJ] button.  
5. Touch the [RTN] key, [ESC] key, or press the  
Switching the front and rear  
monitor lock  
The front monitor lock and rear monitor lock  
allows you to enjoy 2-ZONE.  
[ADJ] button.  
Adjusting the dimmer level  
Use to adjust panel brightness when car lights  
are ON/OFF.  
2-ZONE:  
Use the front monitor lock (or rear monitor lock)  
to lock the receiver screen image (or image  
from a separately sold rear monitor) to switch  
the speaker sound to a sound mode that differs  
from the sound accompanying the image.  
G The factory default:  
When the car light is off: Brightest setting (58  
steps)  
When the car light is on: Medium brightness (29  
steps)  
Notes:  
1. When the panel is open, press the [ADJ]  
The front (rear) monitor lock displays the image of  
an external device (VTR, TV game console, etc.)  
connected to the Visual terminal.  
When 2-ZONE is used, the sound from an  
external device (VTR, TV game console, etc.) can  
only be heard from headphones connected to the  
external device.  
button to display the ADJUST MODE menu.  
2. Touch the [MONITOR] key, and touch the  
[DIMMER LEVEL] key to adjust the dimmer  
level.  
3. Touch the [Î] or [Å] key to adjust.  
4. Touch the [RTN] key, [ESC] key, or press the  
A rear monitor is a separately sold accessory.  
[ADJ] button.  
2-ZONE: 1 (front monitor lock)  
1. Press and hold the [ADJ] button for 1 second  
or longer.  
Warning display when CCD camera  
is installed  
When a TV tuner (sold separately) is installed  
together with optional CCD camera, the  
following warning message is displayed during  
use of the CCD camera: Make sure of safety  
around your vehicle”  
2. Press the [FUNC] button to select the  
desired mode.  
3. To cancel the monitor lock, press the [ADJ]  
button.  
The screen shows the image of the selected  
mode.  
The factory default setting is ON”  
1. Press the [ADJ] button.  
2. Touch the [MONITOR] key, and touch the  
[CCD WARNING] key to switch between  
ONand OFF.  
3. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
VRX746VD  
27  
Basic Operations  
4. Touch the [RTN] key, [ESC] key, or press the  
2-ZONE: 2 (rear monitor lock)  
1. Press the [ADJ] button to display the  
ADJUST MODE menu.  
[ADJ] button.  
5. To cancel the monitor lock, press [ADJ]  
button, touch the [REAR MONI LOCK] key  
and the [OFF] key.  
2. Touch the [MONITOR] key.  
3. Touch the [REAR MONI LOCK] key and the  
6. Touch the [RTN] key, [ESC] key. or press the  
[ON] key.  
[ADJ] button.  
The monitor lock is now canceled.  
GLock system monitor image and sound  
Front monitor lock  
Rear monitor lock  
Visual connection  
[OTHERS]  
Visual connection  
[NAVI]  
Visual connection  
[OTHERS]  
Visual connection  
[NAVI]  
(1)  
Front image  
(receiver  
screen)  
Image of device  
connected to the connected to the  
Visual terminal  
(3)  
Image of device  
Displays image of mode selected  
using the [FUNC] button  
Visual terminal  
Rear monitor  
image  
Displays image of mode selected  
using the [FUNC] button (2)  
Image of device connected to the  
Visual terminal  
(separately  
sold)  
Vehicle speaker Plays sound of mode selected using the [FUNC] button  
sound  
1 A device connected to the Visual terminal should be set up as described in the section Switching  
CONNECT.”  
2 No image is displayed on the rear monitor when a non-image mode such as radio, CD, etc. is  
engaged.  
3 For safety reasons, this image is not displayed when the vehicle is moving. The picture can be  
watched only when the vehicle is standing still and the parking brake is engaged.  
Adjusting the GENERAL  
Setting the BEEP  
Setting the button illumination  
The sound heard when you make operations is  
called beep. The unit can be set up so that it  
does not produce this beep sound.  
The factory default setting is GREEN(green).  
1. When the panel is open, press the [ADJ]  
button to select the ADJUST MODE menu.  
The factory default setting is BEEP ON.  
1. When the panel is open, press the [ADJ]  
2. Touch the [GENERAL] key.  
3. Touch the [KEY ILLUMI] key to select RED”  
button to select the ADJUST MODE menu.  
(red) or GREEN(green).  
2. Touch the [GENERAL] key.  
4. Touch the [RTN] key, [ESC] key, or press the  
Touch the [BEEP] key to select ONand  
OFF.  
[ADJ] button.  
3. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
28  
VRX746VD  
Basic Operations  
Clock Adjustment  
1. When the panel is open, press the [ADJ]  
button to select the ADJUST MODE menu.  
Switching CONNECT(connect)  
Make the following settings when an external  
device is connected to the Visual terminal.  
2. Touch the [GENERAL] key.  
NAVI:  
when a navigation system is  
connected  
When a navigation system is  
connected, use the monitor lock  
function. Locking the monitor locks  
the screen size in F.WIDE mode (full  
wide) and the VTR system to NTSC.  
Touch the [CLOCK] key to adjust the time.  
3. Touch the [w], [z], [a.m] or [p.m] key to  
adjust the time, then touch the [SET] key.  
The time is displayed in 12-hour format.  
4. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
OTHERS: for external devices other than a  
navigation system  
NONE:  
when no external devices are  
connected  
Setting the Auto Panel  
When you remove or attach the DCP, you can  
set the liquid crystal panel automatically housing  
or opening.  
The factory default setting is NONE.  
1. When the panel is open, press the [ADJ]  
button to display the ADJUST MODE menu.  
The factory default setting is ON.  
2. Touch the [GENERAL] key.  
1. Press the [ADJ] button to select the ADJUST  
MODE menu.  
Touch the [CONNECT] key to select NAVI”  
or OTHERSor NONE.  
2. Touch the [GENERAL] key.  
3. Touch the [RTN] key, [ESC] key, or press the  
Touch the [AUTO PANEL] key to set ON,  
OFFor CLOSE.  
[ADJ] button.  
ON:  
The liquid crystal panel houses  
automatically after removing the  
DCP.  
Time setting in air conditioner  
operation mode  
And the liquid crystal panel open  
automatically after attaching the  
DCP.  
This setting can be used to adjust the time the  
panel stays in the horizontal position when in  
the air conditioner operation mode.  
OFF:  
Normal operation.  
* The factory default setting is 10s.  
1. Press the [ADJ] button.  
CLOSE: The liquid crystal panel houses  
automatically after removing the  
DCP.  
2. Touch the [GENERAL] key.  
3. Touch the [HVAC MODE] key to set to 5s,”  
3. Touch the [RTN] key, [ESC] key, or press the  
10s,or 30s.”  
[ADJ] button.  
4. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
VRX746VD  
29  
Radio Operations  
1. Touch the [SRCH] key to switch the KEY  
FM reception  
PAD.  
For enhanced FM performance the  
® tuner includes signal actuated stereo control,  
Enhanced Multi AGC, Impulse noise reduction  
curcuits and Multipath noise reduction circuits.  
2. Touch the [0]~[9] key corresponding with the  
frequency you desired. When you touch the  
wrong number ([0]~[9] key), you can cancel  
that to touch the [CLR] key.  
3. Touch the [ENT] key. The radio station you  
Listening to the radio  
1. Press the [FUNC] button and select the  
Radio mode. The frequency is displayed.  
required would be tuned.  
4. Touch the [ESC] key.  
2. Press the [BAND] button and select the radio  
band. Each time the button is pressed, the  
radio reception band changes in the  
following order:  
Manual tuning  
There are 2 ways available: Quick tuning and  
step tuning.  
FM1 FM2 FM3 AM FM1...  
When you are in the step tuning mode, the  
frequency changes one step at a time. In quick  
tuning mode, you can quickly tune the desired  
frequency.  
3. Press the [a] or [d] button to tune in the  
desired station.  
1. Press the [BAND] button and select the  
Seek tuning  
desired band. (FM or AM)  
1. Press the [BAND] button and select the  
desired band. (FM or AM)  
If “MANU” is not lit in the display, press and  
hold the [BAND] button for 1 second or longer.  
MANU” appears in the display and manual  
tuning is now available.  
2. Tune in to a station.  
If “MANU” is lit in the display, press and hold  
the [BAND] button for 1 second or longer.  
MANU” in the display goes off and seek  
tuning is now available.  
The same operation is also available by using  
the [BAND] key.  
2. Tune into a station.  
The same operation is also available by using  
the [BAND] key.  
G Quick tuning:  
Press and hold the [a] or [d] button for 1  
3. Press the [a] or [d] button to  
second or longer to tune in a station.  
automatically seek a station.  
G Step tuning:  
When the [d] button is pressed, the station  
is sought in the direction of higher  
frequencies; when the [a] button is  
pressed, the station is sought in the direction  
of lower frequencies.  
The same operation is also available by using  
the [å] or [] key.  
Press the [a] or [d] button to manually  
tune in a station.  
Recalling a preset station  
A total of 24 preset positions (6-FM1, 6-FM2, 6-  
FM3, 6-AM) exists to store individual radio  
stations in memory. Pressing the corresponding  
[DIRECT] button recalls the stored radio  
frequency automatically.  
Selecting stations with the KEY PAD  
This function displays the KEY PAD on the screen  
enabling you to tune by entering a frequency.  
There are 2 ways available to recall the preset  
station.  
GUsing the [DIRECT] button  
1. Press the [BAND] button and select the  
desired band. (FM or AM)  
2. Press the corresponding [DIRECT] button to  
recall the stored station.  
Press and hold one of the [DIRECT] buttons  
for 2 seconds or longer to store that station  
into preset memory.  
30  
VRX746VD  
Radio Operations  
GUsing the LIST screen  
1. Press the [BAND] button and select the  
desired band. (FM or AM)  
1. Touch the [LIST] key.  
2. Touch the [LIST] key.  
3. Touch and hold the [AS] key for 2 seconds or  
longer.  
The stations with good reception are stored  
automatically to the preset channels.  
Preset scan  
Preset scan receives the stations stored in  
preset memory in order. This function is useful  
when searching for desired station in memory.  
2. Touch the corresponding [DIRECT] key to  
recall the stored station.  
You can select the desired band to touch the  
1. Touch the [LIST] key.  
[BAND] key.  
2. Touch the [PS] key to start preset scan. The  
unit starts scanning each station for 7  
seconds sequentially.  
Touch and hold one of the [DIRECT] key for 2  
seconds or longer to store the current station  
into preset memory.  
3. When the desired station is turned in, touch  
the [PS] key again to continue receiving that  
station.  
3. Touch the [RTN] key or the [ESC] key to  
return to the previous mode.  
Manual memory  
GUsing the [DIRECT] button  
Instant station recall (ISR)  
Instant station recall is a special radio preset  
that instantly accesses a favorite radio station at  
a touch of a button. The ISR function even  
operates with the unit in other modes.  
1. Press the [BAND] button and select the  
desired band. (FM or AM)  
2. Select the desired station with seek tuning,  
manual tuning, or preset tuning.  
GISR memory  
3. Press and hold one of the [DIRECT] buttons  
for 2 seconds or longer to store the current  
station into preset memory.  
1. Select the station that you wish to store in  
ISR memory.  
2. Press and hold [ISR] button for 2 seconds or  
GUsing the LIST screen  
longer.  
1. Press the [BAND] button and select the  
GRecalling a station with ISR  
desired band. (FM or AM)  
1. In any mode, press [ISR] button to turn on  
the radio function and tune the selected radio  
station. ISRappears in the display. Press  
[ISR] button again to return to the previous  
mode.  
2. Select the desired station with seek tuning,  
manual tuning, or preset tuning.  
3. Touch the screen to display the menu, then  
touch the [LIST] key.  
4. Touch and hold one of the [DIRECT] key for  
2 seconds or longer to store the current  
station into the preset memory.  
Auto store  
Auto store is a function for storing up to 6  
stations that are automatically tuned in  
sequentially. If 6 receivable stations cannot be  
received, a previously stored station remains  
unoverwritten at the memory position.  
VRX746VD  
31  
DVD Video Player Operations  
GWhen watching through a conventional  
type of the rear view monitor (4:3)  
Changing DVD System Settings  
Notes:  
N PS : The leftmost and rightmost areas of  
the screen are cut off.  
• If the SETUP operation is performed in the middle  
of DVD video play, the disc plays from the  
beginning.  
• Various settings of the SETUP menu cannot be  
made with the remote control unit.  
Selecting the DVD SETUP menu  
1. Touch the screen to show the menu screen.  
This function allows displaying the important  
part of image fully on the screen. In some  
cases, image is displayed while being  
panned (scrolled).  
2. Touch the [SUB] key to display the SUB  
MODE screen.  
3. Touch the [SETUP] key to display the DVD  
N LB : A black zone is created in the top and  
SETUP menu.  
bottom areas of the screen.  
This method displays Cinema Scope and  
Vista Vision images without cutting them off  
by creating a black zone on the top and  
bottom gaps.  
4. Touch the [z] key. Touch the [w] key to  
return to the previous menu.  
GWhen watching through a wide type of the  
rear view monitor (16:9)  
WIDE:  
3. Touch the [RTN] key ([ESC] key).  
5. Touch the [RTN] key ([ESC] key).  
Setting up the angle mark display  
You can set up so that the angle mark appears  
on scenes where the angles can be switched.  
Setting up the screen size  
Set up the screen size according to the rear  
view monitor which is connected to this unit.  
1. Follow the steps 1 to 3 in Selecting the  
DVD SETUP menu.  
1. Follow the steps 1 to 3 in Selecting the  
2. Touch the [ANGLE] key to select ONor  
DVD SETUP menu.  
OFF.  
2. Each time you touch the [TV DISPLAY] key,  
you can change amoung the screen size in  
the following order.  
The factory default setting is OFF.  
3. Touch the [RTN] key ([ESC] key).  
WIDE© N PS© N LB© WIDE”  
The factory default setting is WIDE.  
Setting up the disc menu language.  
1. Following the steps 1 to 3 in Selecting the  
DVD SETUP menu, touch the [MENU  
LANGUAGE] key.  
32  
VRX746VD  
DVD Video Player Operations  
2. Touch the key to select a desired language  
to set it.  
Setting up the country code  
Set up the country number for setting up of the  
parental level.  
The factory default setting is ENGLISH.  
3. Touch the [RTN] key ([ESC] key).  
1. Following the steps 1 to 4 in Selecting the  
DVD SETUP menu, touch the [PARENTAL  
LOCALE] key.  
Setting up the audio language  
1. Following the steps 1 to 3 in Selecting the  
DVD SETUP menu, touch the [AUDIO  
LANGUAGE] key.  
2. Touch the ten-key(0 to 9) to input a 4-digit  
country code.  
The factory default setting is 8583(U.S.A).  
I Country code list  
2. Touch the key to select a desired language  
to set it.  
Country  
Region number 3  
Input code  
The factory default setting is ENGLISH.  
BRUNEI DARUSSALAM  
Kingdom of Cambodia  
INDONESIA  
KOREA, DEMOCRATIC PEOPLE S REPUBLIC OF  
KOREA,REPUBLIC OF  
LAO PEOPLE S DEMOCRATIC REPUBLIC  
MALAYSIA  
MYANMAR  
PHILIPPINES  
SINGAPORE  
6678  
7572  
7368  
7580  
7582  
7665  
7789  
7777  
8072  
8371  
3. Touch the [RTN] key ([ESC] key).  
Setting up the subtitle language  
1. Following the steps 1 to 3 in Selecting the  
DVD SETUP menu, touch the [SUB TITLE  
LANG.] key.  
2. Touch the key to select a desired language  
to set it.  
THAILAND  
VIET NAM  
EAST TIMOR  
HONG KONG  
MACAU  
8472  
8678  
8480  
7275  
7779  
8487  
The factory default setting is ENGLISH.  
3. Touch the [RTN] key ([ESC] key).  
Setting up the password for setting  
TAIWAN, PROVINCE OF CHINA  
up of the parental level  
1. Following the steps 1 to 3 in Selecting the  
DVD SETUP menu, touch the  
3. Touch the [ENT] key.  
4. Touch the [RTN] key ([ESC] key).  
[PASSWORD] (password) key.  
Setting up the parental level  
You can change the level of parental lock  
(audio-visual restriction).  
2. Touch the ten-key(0 to 9) to input a 4-digit  
password.  
The factory default setting is 0000.  
Input 4356to return password to 0000.  
Input an old password, and touch the [ENT]  
key.  
This function allows cutting scenes that are  
unfavorable for children or replacing them  
automatically with other scenes prepared in  
advance. For example, by replacing scenes of  
radical violence or portrayals of sex with safe  
scenes, you can make a trouble-free story as if  
it were so from the beginning.  
Input a new password, and touch the [ENT]  
key.  
3. Touch the [RTN] key ([ESC] key).  
Note:  
1. Following the steps 1 to 4 in Selecting the  
DVD SETUP menu, touch the [PARENTAL  
LEVEL] key.  
When a disc with view limited is played  
When a disc with view limited is played, the input  
screen requiring you to input the password may  
appear. When this happens, enter the correct  
password, otherwise play does not start.  
2. When you touch the [w] or [z] key,  
PASSWORD input screen is displayed.  
3. Touch the ten-key(0 to 9) to input a 4-digit  
password, and touch the [ENT] key.  
The factory default setting of the password is  
0000.  
4. Touch the [w] or [z] key to select level 1 to  
8, or 0 (no parental).  
The factory default setting is 8.  
VRX746VD  
33  
DVD Video Player Operations  
5. Touch the [RTN] key ([ESC] key).  
Basic Operations  
The relationship between DVD video category  
codes and parental level are shown in the table  
below. Use this table when setting the parental  
level.  
Loading a disc  
Insert a disc into the centre of the insertion slot  
with the label side facing up. The disc plays  
automatically after loading.  
LEVEL7  
LEVEL6  
LEVEL4  
LEVEL3  
LEVEL1  
NC-17  
Notes:  
(NO ONE 17 AND UNDER ADMITTED)  
Never insert foreign objects into the disc insertion  
slot.  
If the disc is not inserted easily, there may be  
another disc in the mechanism or the unit may  
require service.  
R
(RESTRICTED)  
PG-13  
(PARENTS STRONGLY CAUTIONED)  
8 cm (single play) discs cannot be used.  
PG  
(PARENTAL GUIDANCE SUGGESTED)  
CAUTION  
G
(GENERAL AUDIENCES)  
With the screen open, a driver may not see the  
disc insertion slot. For your safety, insert a disc  
with the screen closed.  
The contents that the parental level  
restricts varies with the country code.  
Watching/Listening to a disc  
already inserted  
1. Press the [FUNC] button to select the DVD  
mode. Play starts automatically. If no disc is  
loaded in the unit, NO DISCappears in the  
display.  
WARNING  
• Videos may be played back with particu-  
larly loud sound. Increase the volume  
gradually from the minimum after the  
video images are displayed.  
• For your safety, the driver should not  
watch the video or operate the controls  
while driving. Please note that watching  
and operating the video while driving are  
prohibited by law in some countries.  
Notes:  
For your safety, the VRX746VD has a safety  
function which turns off the picture when the car  
is moving, so only the audio can be heard. The  
picture can only be watched when the car is  
stopped and the parking break is applied.  
When playing an NTSC format DVD video and  
video CD, no image will be produced at the rear  
monitor (not applicable to Korea-market model).  
Pausing play  
1. Press the [s] button to pause play.  
PAUSEappears in the display.  
2. To resume disc play, press the [s] button  
again.  
34  
VRX746VD  
DVD Video Player Operations  
4. Select the DVD menu contents use either the  
Cross KEY PADor the TEN KEY PAD”  
according to the disc contents menu.  
Ejecting a disc  
1. Press the [Q] button a disc ejects. EJECT”  
appears in the display. The play mode then  
switches to Radio.  
5. Touch the [ENT] key and touch the [ESC]  
key.  
If a disc is left in the ejected position for 15  
seconds, the disc is automatically reloaded  
(Auto reload). In this case, however, the play  
mode will remain set to Radio.  
Switching KEY PAD position  
When the KEY PAD becomes difficult to view in  
the menu display, you can move it to the other  
side of the screen.  
Note:  
If you force a disc into before auto reloading, this  
can damage the disc.  
KEY PAD  
DVD Video Operations  
Watching a DVD-Video  
After disc loading, the play mode is  
automatically engaged.  
Button operation may not be allowed  
depending on the story of the disc.  
GAfter the menu screen is displayed  
For normal DVD-Video discs, the DVD menu  
screen appears.  
After the DVD menu screen is displayed, select  
an item in the following operations and play it  
back.  
Showing the DVD menu  
1. Touch the screen to show the menu screen.  
Touch the [MENU] key during playback.  
The DVD menus appears.  
The displayed contents may differ,  
depending on the DVD software.  
KEY PAD  
Example showing DVD menu display  
Stopping playback  
1. Touch and hold the [s] key for 1 second  
or longer during playback. Playback stops.  
2. To resume playback. Touch the [s] key,  
and playback resumes from the scene where  
playback is stopped.  
Pausing playback  
2. To select the DVD menu contents, touch the  
[KEY] key. The Cross KEY PAD(wzÅ  
Î) is displayed.  
1. Press the [s] button or touch the [s]  
key during playback. Playback pauses.  
2. To resume playback. Press the [s] button,  
3. Touch the [NUM] key, the display changes to  
and playback resumes.  
the TEN KEY PAD(0~9).  
Touch the [+] key to return to the Cross  
KEY PAD.  
VRX746VD  
35  
DVD Video Player Operations  
Slow playback  
Fast forward and fast backward  
1. Press and hold the [a] or [d] button during  
playback.  
1. Press the [s] button or touch the [s]  
key, then press and hold the [d] button or  
the [] key. While the button or key is  
being pressed, slow playback continues at  
the speed 1/3 times the normal playback.  
Press and hold the button, and the playback  
speed becomes 5-time faster first and then  
20-time faster 3 seconds later. Release the  
button, and the normal speed is restored.  
Slow playback cannot be performed in the  
backward direction. In addition, audio  
cannot be reproduced during slow  
playback.  
No audio is reproduced during fast forward  
and fast rewind operation.  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [å] or []  
key.  
Skipping a chapter (searching)  
About chapter  
The fast forward and fast rewind speed  
may differ depending on the disc.  
Chapter means a small segment to divide the  
data area of the disc.  
The menu screen may appear when the  
button is pressed.  
1. Press the [a] / [d] button or touch the  
[å] / [] key during playback.  
Chapters are skipped, as many as the times  
the button is pressed, and playback starts.  
Searching with a chapter/title  
number  
Current  
location  
or  
or  
You can locate the beginning of the scene using  
the chapter numbers or title numbers recorded  
on the DVD-Video disc.  
1. Touch the screen to display the menu screen.  
Chapter  
up  
Chapter  
down  
Chapter  
2. Touch the [SRCH] key.  
Each time you touch the [SFT] key, you can  
switch between title number input [T**]and  
chapter number input [C***].  
Press the [d] button, and playback starts  
from the beginning of the next chapter.  
Title  
Press the [a] button, and playback starts  
from the beginning of the current chapter.  
When this button is pressed again within  
about 2 seconds, playback starts from the  
beginning of the previous chapter.  
A large segment to divide the data area of  
the disc.  
Chapter  
A small segment to divide the data area of  
the disc.  
The unit may return to the menu screen  
when the [d] or [a] button is pressed.  
3. Input the number of the title that you want to  
play back with the [0] to [9] key.  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [å] or []  
key.  
4. Touch the [ENT] key.  
Playback starts from the scene of the input  
title number or chapter number.  
If the input title number does not exist or  
searching with a title number is not  
allowed, the screen image will not change.  
5. Touch the [ESC] key.  
36  
VRX746VD  
DVD Video Player Operations  
Scan playback  
Switching among languages  
On discs in which two or more audios or audio  
languages have been recorded, you can switch  
among the audio languages during playback.  
Scans and plays back all chapters recorded on  
the DVD-Video, the first 10 seconds for each.  
1. Touch the screen to display the menu, then  
touch the [SUB] key.  
1. Touch the screen to display the menu, then  
touch the [SUB] key.  
2. Touch the [SCAN] key, then touch the [RTN]  
key. The message C.SCNwill be displayed.  
2. Touch the [AUDIO] key during playback.  
After scan playback of all chapters on the  
disc, chapter scanning through the same  
disc is performed again.  
Each time you touch the key, you can switch  
among audio languages.  
Depending on the disc, up to 8 audios may  
Depending on the disc, the menu may  
appear again after scan playback of all  
chapters within the title.  
be recorded. For details, see the mark of  
8
the disc (  
: Indicates that 8 audios have  
been recorded).  
3. Touch the [C.SCN] key to turn off the scan  
When the power is turned on and when the  
disc is changed with a new one, the  
language set at the time of factory  
shipment is selected. If that language has  
not been recorded, the language specified  
on the disc.  
playback.  
Repeat playback  
This operation plays back chapters recorded on  
the DVD-Video repeatedly.  
Depending on the disc, switching may be  
completely impossible or impossible on  
some scenes.  
1. Touch the screen to display the menu, then  
touch the [SUB] key.  
2. Touch the [REPEAT] key, then touch the  
[RTN] key. The message C.RPTwill be  
displayed.  
It may take time to switch among audios.  
Switching subtitles  
On DVD discs in which two or more subtitle  
languages have been recorded, you can switch  
among the subtitle languages during playback.  
3. Touch the [C.RPT] key to turn off the repeat  
playback.  
TOP function  
The TOP function resets the DVD player to the  
first chapter of the track.  
1. Touch the screen to display the menu, then  
touch the [SUB] key.  
2. Touch the [SUB TITLE] key during playback.  
1. Press the [BAND] button to playback the first  
Each time you touch the key, you can switch  
among subtitles.  
chapter(chapter No. 1).  
Depending on the disc, up to 32 kinds of  
Using the title menu  
On DVD discs containing two or more titles, you  
can select from the title menu for playback.  
subtitles may be recorded. For details, see  
8
the mark of the disc ( : Indicates that 8  
kinds of subtitles have been recorded).  
1. Touch the screen and touch and hold the  
[MENU] key for 1 second or longer during  
playback.  
Depending on the disc, switching may be  
completely impossible or impossible on  
some scenes.  
The title menu screen appears.  
It may take time to switch among subtitles.  
Depending on the disc, the title menu  
cannot be called.  
GTo turn off subtitles  
1. Touch the [SUB TITLE] key several times,  
2. Touch the [KEY] key, and touch the [w],  
and subtitles are turned off.  
[z], [Å] or [Î] key to select the item.  
In initial setting:  
Depending on the disc, items cannot be  
selected with the ten-key buttons.  
Off Subtitle 1 Subtitle 2  
3. Touch the [ENT] key.  
Subtitle X  
4. Touch the [ESC] key.  
VRX746VD  
37  
DVD Video Player Operations  
Switching angles  
On DVD discs in which video images have been  
recorded in two or more angles, you can switch  
among the angles during playback.  
Watching a video CD  
After disc loading, the play mode is  
automatically engaged.  
Button operation may not be allowed  
depending on the story of the disc.  
This operation can be performed when the  
Setting up the angle mark displayfunction  
(see P. 32) is set to ON.  
IAfter the menu screen is displayed  
1. Touch the screen.  
For V-CD discs equipped with the PBC (Play  
Back Control) function, the menu screen  
appears. After the menu screen is displayed,  
select an item in the following operations and  
play it back.  
2. Touch the [  
playback.  
] (Angle mark) key during  
Each time you touch the key, you can switch  
among angles.  
Depending on the disc, up to 9 angles may  
be recorded. For details, see the mark of  
Showing the V-CD menu (for V-CD  
discs with PBC)  
the disc (  
: Indicates multi-angle).  
This key does not function on some discs.  
Depending on the disc, angles may switch  
smoothly or switch with a momentary still  
image.  
1. Touch the screen to display the menu  
screen. Touch the [MENU] key during  
playback.  
When the power is turned on and when the  
disc is changed with new one, the  
language set at the time of factory  
shipment is selected. If that language has  
not been recorded, the language specified  
on the disc.  
The V-CD menu appears.  
The displayed contents may differ,  
depending on the V-CD software.  
Example showing menu display  
Depending on the disc, switching may be  
completely impossible or impossible on  
some scenes.  
It may take time to switch among angles.  
Depending on the disc, scenes recorded in  
two or more angles may be played back.  
2. To select the V-CD menu contents, touch the  
[KEY] key and use either the Cross KEY  
PADor the Ten KEY PADaccording to the  
disc contents menu.  
Displaying the playback status  
1. Touch the screen to display the menu, then  
touch the [SUB] key. Touch the [P.TIME] key  
during playback. Playback status is display  
on the screen.  
Pausing playback  
1. Press the [s] button. Playback stops.  
To resume playback, press the [s] button,  
and playback resumes from the scene where  
playback is stopped.  
2. Touch the screen to turn off the display. The  
display will turn off after 7 seconds.  
38  
VRX746VD  
DVD Video Player Operations  
Slow playback  
Fast forward and fast backward  
1. Press and hold the [a] or [d] button during  
playback.  
1. Press the [s] button then press and hold  
the [d] button.  
While the button is being pressed, slow  
playback continues at the speed 1/3 times  
the normal playback.  
Press and hold the button, and the playback  
speed becomes 5-time faster first and then  
20-time faster 3 seconds later. Release the  
button, and the normal speed is restored.  
Slow playback cannot be performed in the  
backward direction. In addition, audio  
cannot be reproduced during slow  
playback.  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [å] or []  
key.  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [å] or []  
key.  
No audio is reproduced during fast forward  
and fast rewind operation.  
The unit may return to the menu screen  
when the button is pressed.  
Skipping a track (searching)  
1. Press the [a] / [d] button or touch the  
[å] / [] key during playback.  
Searching with a track number  
This operation allows searching with the track  
numbers recorded on the video CDs.  
The track is skipped and playback starts.  
1. Touch the screen.  
Current  
or  
location  
Track  
or  
2. Touch the [SRCH] key.  
3. Input the number of the track that you want  
to play back with [0] to [9] key.  
Track  
Track  
4. Touch the [ENT] key.  
Playback starts from the scene of the input  
track number.  
Backward  
direction  
Playback  
direction  
If the input track number does not exist or  
searching with a track number is not  
allowed, the screen image will not change.  
If you are playing a disc with PBC and the  
PBC function is engaged, this operation may  
not be performed.  
Press the [d] button, and playback starts  
from the beginning of the next track.  
Press the [a] button, and playback starts  
from the beginning of the current track.  
When this button is pressed again within  
about 2 seconds, playback starts from the  
beginning of the previous track.  
5. Touch the [ESC] key.  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [å] or []  
key.  
Changing audio output  
You can change the audio output method.  
1. Touch the screen to display the menu, then  
In the case of some discs furnished with PBC  
function, when PBC is set to ON, this  
operation will cause the menu screen to be  
displayed.  
touch the [SUB] key.  
2. Touch the [AUDIO] key during playback.  
Each time you touch the key, you can switch  
among audio output methods.  
L (Left) R (Right) STEREO  
VRX746VD  
39  
DVD Video Player Operations  
Displaying the playback status  
1. Touch the screen to display the menu, then  
touch the [SUB] key.  
Skipping a track (searching)  
1. Press the [a] or [d] button during  
playback.  
2. Touch the [P.TIME] key.  
Tracks are skipped, as many as the times  
the button is pressed, and playback starts.  
Playback status is displayed on the screen.  
Press the [d] button, and playback starts  
3. Touch the screen to turn off the display. The  
display will turn off after 7 seconds.  
from the beginning of the next track.  
Press the [a] button, and playback starts  
from the beginning of the current track.  
When this button is pressed again within  
about 2 seconds, playback starts from the  
beginning of the previous track.  
On/off of Playback Control  
The factory default setting is ON.  
On video CDs equipped with Play Back Control  
function, you can turn it on/off.  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [å] or []  
key.  
1. Touch the screen to display the menu, then  
touch the [SUB] key.  
2. Each time you touch the [PBC] key, you can  
switch between on and off.  
When the PBC is turned on or off, the disc  
plays from the beginning.  
TOP function  
The TOP function resets the DVD player to the  
first track of the disc.  
GPlayback control (PBC)  
This control signal is recorded on a Video CD  
for version 2.0 and used to control playback.  
Using pre-recorded menu screens in the Video  
CD with PBC, you can enjoy playback of  
software with a simplified dialog function or  
software with search function. You can also  
enjoy a still picture at high or standard  
resolution.  
1. Press the [BAND] button to playback the first  
track (track No. 1).  
Fast forward and fast backward  
1. Press and hold the [a] or [d] button during  
playback.  
Press and hold the button, and the playback  
speed becomes 5-time faster first and then  
20-time faster 3 seconds later. Release the  
button, and the normal speed is restored.  
Listening to a CD  
This unit is a CD TEXT compatible model.  
This unit supports the display of the DISC TITLE,  
TRACK TITLE and ARTIST of the CD TEXT.  
Searching with a track number  
This operation allows searching using the track  
numbers recorded on the CDs.  
After disc loading, the play mode is  
automatically engaged.  
1. Touch the [SRCH] key.  
Note:  
2. Input the number of the track that you want  
This unit supports only CD TEXT in English. Also,  
some character data may not be reproduced  
properly on the display.  
to play back with [0] to [9] key.  
3. Touch the [ENT] key.  
Playback starts from the scene of the input  
track number.  
Pausing playback  
If the input track number does not exist or  
searching with a track number is not  
allowed, the screen image will not change.  
1. Press the [s] button or touch the [s]  
key during playback.  
Playback pauses.  
4. Touch the [ESC] key.  
2. To resume playback, press the [s] button  
or touch the [s] key, and playback  
resumes.  
40  
VRX746VD  
DVD Video Player Operations  
Note:  
Selecting a track on the LIST screen  
This function allows you to select tracks from a  
displayed list.  
The scan playback function can also be  
performed using the title list screens [T.SCN] key.  
To cancel play, touch the [T.SCN] key once again.  
1. Touch the [LIST] key.  
The list menu will appear.  
Displaying CD titles  
This unit can display title data for CD-text CDs.  
2. Press the [w] or [z] button to change the  
track display.  
1. Touch the [DISC], [TRACK], or [ARTIST] key  
to cause the respective display to scroll  
once.  
3. Touch the desired track title key.  
The corresponding track will begin playback.  
The titles will scroll when the selected  
tracks “ ” mark is touched.  
Listening to an MP3  
This unit is a ID3 Tag compatible model.  
4. Press the [RTN] key to return to the previous  
screen.  
This unit supports the title, artist and album dis-  
play of the ID3 Tag versions 1 and 1.1.  
Other various play functions  
1. Touch the [SUB] key.  
After disc loading, the play mode is  
automatically engaged.  
What is MP3?  
MP3 is an audio compression method and  
classified into audio layer 3 of MPEG standards.  
This audio compression method has penetrated  
into PC users and become a standard format.  
This MP3 features the original audio data  
compression to about 10 percent of its initial  
size with a high sound quality. This means that  
about 10 music CDs can be recorded on a CD-  
R disc or CD-RW disc to allow a long listening  
time without having to change CDs.  
2. Touch the touch key of the function you want  
to play.  
* [SCAN]; scan playback  
This operation scans and plays back all tracks  
recorded on the disc, the first 10 seconds for  
each.  
Note:  
Some CDs recorded on CD-R mode may not be  
usable.  
* [REPEAT]; repeat playback  
This operation plays back tracks recorded on  
the CD repeatedly.  
Displaying MP3 ID3-TAG titles  
ID3 information such as title, artist and album  
title can be displayed for an MP3 file containing  
ID3 Tag information.  
* [RANDOM]; random playback  
This operation plays back all tracks on the  
disc in no particular order.  
3. Touch the [RTN] key to return to the previous  
screen.  
Precautions when creating an MP3 disc  
GFile extensions  
1. Always add a file extension .MP3or .mp3”  
to an MP3 file by using single byte letters. If  
you add a file extension other than specified  
or forget to add the file extension .MP3or  
.mp3, the file cannot be played. In addition,  
if you use upper case and lower case letters  
(capital and small letters) mixedly for file  
extensions, normal play may not be possible.  
Use to display current play status, and also as  
the cancel key.  
2. Files without MP3 data will not play.  
4. To cancel play, touch the [T.SCN] ([T.RPT] or  
[T.RDM]) key.  
VRX746VD  
41  
DVD Video Player Operations  
GLogical format (File system)  
Pausing playback  
1. When writing an MP3 file on a CD-R disc,  
please select ISO9660 level 1 or level 2  
(without including expansion format)as  
the writing software format. Normal playback  
may not be possible if the disc is recorded on  
another format.  
1. Press the [s] button or touch the [s]  
key during playback.  
Playback pauses.  
2. To resume playback, press the [s] button  
or touch the [s] key again, and playback  
resumes.  
2. The folder name and filename can be  
displayed as the title during MP3 play but the  
title must be within 31 and 27 single byte  
alphabetical letters and numerals for the  
folder name and filename, respectively  
(without including an extension). Entering  
more letters or numerals than specified may  
cause an incorrect display.  
Skipping a track (searching)  
1. Press the [a] or [d] button during  
playback.  
Tracks are skipped, as many as the times  
the button is pressed, and playback starts.  
Press the [d] button, and playback starts  
GFolder structure  
from the beginning of the next track.  
1. A disc with a folder having more than 8  
hierarchical levels will conflict with the  
ISO9660 and playback will be impossible.  
Press the [a] button, and playback starts  
from the beginning of the current track.  
When this button is pressed again within  
about 2 seconds, playback starts from the  
beginning of the previous track.  
GNumber of files or folders  
1. The maximum allowable number of folders is  
255 (including root directory); the maximum  
allowable number of files is 512 (max. 255 per  
folder). This represents the maximum number  
of tracks that can be played back.  
This operation skips the track over the folder.  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [å] or []  
key.  
2. Tracks are played in the order that they were  
recorded onto a disc. (Tracks might not  
always be played in the order displayed on  
the PC.)  
Fast forward and fast backward  
1. Press and hold the [a] or [d] button during  
playback.  
Some noise may occur depending on the  
type of encoder software used while  
recording.  
Press the button, and the playback speed  
becomes 5-time faster first and then 20-time  
faster 3 seconds later. Release the button,  
and the normal speed is restored.  
In case of a track recorded at VBR  
(variable bit rate), the display for the play  
time of the track may be slightly different  
from the actual play time. Also, the  
recommended value of VBR ranges from  
64 kbps to 320 kbps.  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [å] or []  
key.  
Depending on the damage conditions of a  
file, it may occur that the file is not played  
and the next file is played instead. Also, if  
the damage is in a severe condition, play  
stops showing the ERROR 3display.  
Selecting a folder/track on the LIST  
screen  
1. Touch the [LIST] key during playback.  
After disc selection, the play mode is  
automatically engaged.  
Note:  
If ID3 Tag information was entered with 2-byte  
characters, it may occur that the characters are  
not reproduced properly on the display.  
Folders (tracks) are displayed.  
2. Touch the [w] or [z] key to select a folder  
and touch the folder name.  
The titles will scroll when the selected  
folders “  
mark is touched.  
The track selection screen appears.  
42  
VRX746VD  
DVD Video Player Operations  
3. Touch the [w] or [z] key to select the track  
* FOLDER [REPEAT]; folder repeat playback  
and touch the track name.  
This operation plays back tracks in an MP3  
folder repeatedly.  
When the selected tracks “ ” mark is  
touched, the titles will scroll.  
* TRACK [RANDOM]; track random playback  
Touch the [RTN] key to return to the folder  
select (LIST) screen.  
This operation plays the tracks in the folder in  
a random order.  
4. Touch the [ESC] key.  
* FOLDER [RANDOM]; folder random  
playback  
Playback by selecting a folder and  
track (Direct select mode)  
This operation allows searching using the folder  
and track numbers recorded on the MP3 disc.  
This operation plays back tracks recorded on  
the disc in no particular order.  
3. Touch the [RTN] key, return to the previous  
screen.  
1. Touch the [SRCH] key.  
Each time you touch the [SFT] key, you can  
switch between T000for track number  
input and F000for folder number input.  
2. Input the number for the track or folder that  
you want to play back with [0] to [9] key.  
3. Touch the [ENT] key.  
When you select the folder number playback  
starts from track 1 of the input folder number.  
Use to display current play status, and also as  
the cancel key.  
4. Touch the [ESC] key.  
4. To cancel play, touch the [T.SCN] ([F.SCN],  
[T.RPT], [F.RPT], [T.RDM] or [F.RDM]) key.  
Other various play functions  
1. Touch the [SUB] key.  
Notes:  
The scan playback function can also be  
performed using the title list screens [T.SCN] key.  
To cancel play, press the [T.SCN] key once again.  
The folder playback function can also be  
performed using the title list screens [F.SCN] key.  
To cancel play, press the [F.SCN] key once again.  
TOP function  
The TOP function resets the DVD player to the  
first track of the disc.  
2. Touch the touch key of the function you want  
to play.  
1. Press the [BAND] button to playback the first  
track (track No. 1).  
* TRACK [SCAN]; track scan playback  
This operation scans and plays back all tracks  
recorded on the disc, the first 10 seconds for  
each.  
* FOLDER [SCAN]; folder scan playback  
This operation plays back the first tracks of all  
folder on the MP3 disc, the first 10 seconds  
for each.  
* TRACK [REPEAT]; track repeat playback  
This operation plays back the tracks currently  
being playback repeatedly.  
VRX746VD  
43  
VISUAL Operations  
CD Changer Operations  
Note:  
This function is available when a VTR, etc. is  
connected to the visual terminal.  
When an optional DVD (CD) changer is  
connected through the CeNET cable, this unit  
controls all DVD (CD) changer functions. This unit  
can control a total of 2 changers (CD and/or  
DVD).  
WARNING  
For your safety, the driver should not watch  
the VTR, etc. or operate the controls while  
driving. Please note that watching and op-  
erating the VTR, etc. while driving are pro-  
hibited by law in some countries.  
CD changer functions  
Press the [FUNC] button and select the CD  
changer mode to start play. If 2 CD changers  
are connected, press the [FUNC] button to  
select the CD changer for play.  
Switching to the VISUAL mode  
Note:  
If NO MAGAZINEappears in the display, insert  
the magazine into the CD changer. DISC  
CHECKINGappears in the display while the  
player loads (checks) the magazine.  
For your safety, the VRX746VD has a safety  
function which turns off the picture when the car  
is moving, so only the audio can be heard. The  
picture can only be watched when the car is  
stopped and the parking break is applied.  
If NO DISCappears in the display, eject the  
magazine and insert discs into each slot. Then,  
reinsert the magazine back into the CD changer.  
1. Press the [FUNC] buton and select the  
VISUAL mode.  
CAUTION  
CD-ROM discs cannot be played in the CD  
changer.  
Changing the audio input level  
The visual terminal can be used to change the  
input audio level.  
Pausing play  
The factory default setting is HIGH.  
1. Touch the screen to display the menu, then  
1. Press the [s] button or touch the [s]  
key to pause play. PAUSEappears in the  
display.  
touch the [SUB] key.  
2. Touch the [VISUAL AUX SENS] key to select  
2. To resume play, press the [s] button or  
the level.  
touch the [s] key again.  
HIGH: 16.25 dB  
MID: 3.75 dB  
LOW: 0 dB  
Switching the CD TEXT titles  
This operation is only possible when this unit is  
connected with a CD TEXT compatible CD  
changer.  
3. Touch the [ESC] key to return to previous  
screen.  
You can select the CD TEXT titles among the  
disc titles, track titles and artist titles.  
When the panel is closed:  
1. Press the [DISP] button to show the SUB  
display. The disc title, track title or artist titles,  
user title is displayed.  
2. Each time you press and hold the [DISP]  
button for 1 second or longer, the display  
toggles among the disc title, the track title or  
the artist titles, user title.  
The selected title scrolls once.  
When panel is open, titles will not be  
displayed on the information panel.  
44  
VRX746VD  
CD Changer Operations  
When the panel is open:  
Selecting with a track number  
1. Touch the [DISC], [TRACK], [ARTIST], or  
[USER] key to select the desired title.  
The selected titles except for the user title  
scroll once.  
Selecting a CD  
When the panel is closed:  
Each of the [DIRECT] buttons corresponds to a  
disc loaded into the magazine.  
GSelecting a disc from 1 to 6  
Press the corresponding [DIRECT] button (1 to  
6) to select the desired disc.  
1. Touch the [SRCH] key.  
2. Touch the [0] ~ [9] key corresponding with  
the track you desired. When you touch the  
wrong number([0] ~ [9] key), you can cancel  
that to touch the [CLR] key.  
GSelecting a disc from 7 to 12 (only when a  
12 disc CD changer is used.)  
Press the corresponding [DIRECT] button (1 to  
6) for 1 second or more, then select the desired  
disc.  
3. Touch the [ENT] key.  
The specified track is selected and playback  
starts.  
When the panel is open:  
Each of the [DIRECT] keys corresponds to a  
disc loaded into the magazine.  
Selecting a track  
GSelecting a disc from 1 to 6  
GTrack-up  
1. Touch the [LIST] key.  
1. Press the [d] button to move ahead to the  
2. Touch the corresponding [DIRECT] key (1 to  
beginning of the next track.  
6) to select the desired disc.  
2. Each time you press the [d] button, the  
track advances ahead to the beginning of the  
next track.  
When the panel is open, the same operation  
is also available by using the [] key.  
GTrack-down  
The track selecting screen appears.  
When the “ ” mark of selecting disc is  
touched, the title will scroll.  
3. Touch the [w] or [z] key to select the track  
and touch the track title.  
When the “ ” mark of selecting track is  
touched, the title will scroll.  
1. Press the [a] button to move back to the  
beginning of the current track.  
4. Touch the [RTN] key to return to the track  
2. Press the [a] button twice to move to the  
selecting screen.  
beginning of the previous track.  
GSelecting a disc from 7 to 12 (Only when a  
12 disc CD changer is used.)  
When the panel is open, the same operation  
is also available by using the [å] key.  
Touch the [z] key.  
Touch the corresponding [DIRECT] key (7 to 12)  
to select the desired disc.  
Fast-forward/Fast-backward  
GFast-forward  
Press and hold the [d] button for 1 second or  
Switching to a next disc. (Disc Up  
longer.  
function)  
The disc up function plays from the first track  
(track No.1) of the next disc.  
When the panel is open, the same operation  
is also available by using the [] key.  
GFast-backward  
Press the [BAND] button.  
Press and hold the [a] button for 1 second or  
longer.  
Each time you press the [BAND] button, the  
disc changes to the next disc.  
When the panel is open, the same operation  
is also available by using the [å] key.  
VRX746VD  
45  
CD Changer Operations  
* DISC [RANDOM]; disc random playback  
TOP function  
The disc random play selects and plays  
individual tracks or discs automatically in no  
particular order.  
The TOP function plays from the first track  
(track No. 1) of the disc.  
GWhen playing a disc 1 to 6  
3. Touch the [RTN] key, return to the previous  
Press the [DIRECT] button (1 to 6) with the  
same number as the CD playing.  
screen.  
GWhen playing a disc 7 to 12 (only when a  
12 disc CD changer is used.)  
Press the [DIRECT] button (1 to 6) with the  
same number as the CD playing for 1 second or  
longer.  
Other various play functions  
This function continues on the disc until it is  
cancelled or the mode is changed.  
Use to display current play status, and also as  
the cancel key.  
1. Touch the [SUB] key.  
4. To cancel play, touch the [T.SCN] ([D.SCN],  
[T.RPT], [D.RPT], [T.RDM] or [D.RDM]) key.  
2. Touch the touch key of the function you want  
to play.  
* TRACK [SCAN]; track scan playback  
This scan play locates and plays the first 10  
seconds of each track on a disc automatically.  
* DISC [SCAN]; disc scan playback  
This scan play locates and plays the first 10  
seconds of the first track on each disc in the  
currently selected CD changer.  
* TRACK [REPEAT]; track repeat playback  
The repeat play continuously plays the current  
track.  
* DISC [REPEAT]; disc repeat playback  
After all tracks in the current disc have been  
played, the disc repeat play automatically  
replays the current disc over from the first  
track.  
* TRACK [RANDOM]; track random playback  
The random play selects and plays individual  
tracks on the disc in no particular order.  
46  
VRX746VD  
DVD Changer Operations  
TV Operations  
Only basic operations of DVD changer can be  
performed from the unit. Use the remote control  
unit to perform the following functions.  
TV functions  
When an optional TV tuner is connected through  
the CeNET cable, this unit controls all TV tuner  
functions. To watch TV requires a TV tuner.  
• SCAN, REPEAT, RANDOM function  
• V-CD PBC function ON/OFF  
WARNING  
• DVD SETUP function, AUDIO, SUBTITLE,  
ANGLE setting function  
For your safety, the driver should not  
watch the TV or operate the controls  
while driving. Please note that watching  
and operating the TV while driving are  
prohibited by law in some countries.  
For details on operations other than those  
described below, see DVD player Operation.  
For details on DVD changer precautions, refer  
to the supplied owner’s manual.  
Note:  
Watching TV  
• When the DVD changer (VCZ625) is connected  
via optical cable, no sound will be output if AUDIO  
OUT is switched to ANALOG on the changer’s  
“GENERAL SETUP” menu.  
Note:  
• For your safety, the VRX746VD has a safety  
function which turns off the picture when the car  
is moving, so only the audio can be heard. The  
picture can only be watched when the car is  
stopped and the parking break is applied.  
Selecting a disc  
When the panel is closed :  
1. Press the [FUNC] button and select the TV  
mode.  
Each of the [DIRECT] button corresponds to a  
2. Press the [BAND] button to select the  
desired TV band (TV1 or TV2). Each time  
the button is pressed, the input selection  
toggles between TV1 and TV2.  
disc loaded into the DVD changer.  
Press the [DIRECT] button (1 to 6) and select  
the desired disc.  
When the panel is open :  
3. Press the [d] or [a] button to tune in the  
Touch the [LIST] key, otherwise press the [DISC  
SEL] button on the remote control unit.  
desired TV station.  
When the panel is open, the same operation  
is also available by using the [å] or []  
key.  
Touch the [DIRECT] key (1 to 6) in the display  
or press the numeric button for the disc number  
(1 to 6) on the remote control unit to select the  
desired disc.  
Watching a video  
The TV tuner has a VTR input terminal to which  
1 external device can be connected. Connect a  
12V video cassette player (VCP) or video  
cassette recorder (VCR) to the TV tuner input  
terminal.  
Switching to a next disc  
(Disc Up function)  
The disc up function plays from the first track  
(track No.1) of the next disc.  
1. Touch the screen to display the menu, then  
Press the [BAND] button.  
touch the [SUB] key.  
Each time you press the [BAND] button, the  
disc changes to the next disc.  
When the remote control unit supplied with the  
DVD changer (VCZ625) is used to operate this  
component, some operation buttons are not  
supported.  
2. Touch the [EXTRA SELECT] key in the  
menu screen when the “VTR” is displayed.  
3. To return to the TV broadcast, touch the  
screen again and touch the [EXTRA  
SELECT] key in the menu screen.  
VRX746VD  
47  
TV Operations  
GStep tuning:  
Seek tuning  
1. Press the [BAND] button and select the  
desired TV band (TV1 or TV2).  
Press the [d] or [a] button to manually tune  
in a station.  
Notes:  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [BAND] key.  
If MANUis lit in the display, press and hold  
the [BAND] button for 1 second or longer.  
MANUin the display goes off and seek  
tuning is now available.  
The same operation can be performed by touching  
the screen to display the menu screen, then  
touching the [å] or [] key.  
Manual tuning is cancelled if you do not operate the  
unit for 7 seconds longer. (Only when connecting  
the TTX7503z or TTX7504z with this unit)  
2. Press the [d] or [a] button to  
automatically seek a station. Press the [d]  
button to automatically tune up the frequency  
band to the next available TV station; press  
the [a] button to automatically tune down.  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [å] or [] key.  
Recalling a preset station  
A total of 12 TV stations can be stored (6-TV1  
and 6-TV2). This allows you to select your  
favorite TV stations and store them in memory  
for later recall.  
There are 2 ways available to recall the preset  
station.  
GUsing the [DIRECT] button  
Selecting with a station number  
1. Press the [BAND] button and select the  
Note:  
desired TV band. (TV1 or TV2)  
Cannot be used when TV tuner TTX7504z is  
connected.  
1. Touch the screen to display the menu, then  
2. To recall a stored TV station, press the  
desired [DIRECT] button to select that  
station.  
touch the [SRCH] key.  
Press and hold one of the [DIRECT] buttons  
for 2 seconds or longer to store the current  
station into the preset memory.  
2. Touch the [0]~[9] key corresponding with the  
station you desired. When you touch the  
wrong number ([0]~[9] key), you can cancel  
that to touch the [CLR] key.  
GUsing the LIST screen  
1. Touch the screen to display the menu, then  
3. Touch the [ENT] key. The radio station you  
touch the [LIST] key.  
required would be tuned.  
2. Touch the corresponding [DIRECT] key to  
4. Touch the [ESC] key.  
recall the stored station.  
You can select the desired band to touch the  
[BAND] key.  
Manual tuning  
There are 2 ways available: Quick tuning and  
step tuning. When you are in the step tuning  
mode, the frequency changes one step at a  
time. In quick tuning mode, you can quickly tune  
the desired frequency.  
Touch and hold one of the [DIRECT] key for 2  
seconds or longer to store the current station  
into the preset memory.  
3. Touch the [RTN] key to return to the previous  
mode.  
1. Press the [BAND] button and select the  
desired band. (TV1 or TV2)  
Manual memory  
The same operation can be performed by  
touching the screen to display the menu  
screen, then touching the [BAND] key.  
GUsing the [DIRECT] button  
1. Select the desired station with seek tuning,  
manual tuning or preset tuning.  
If MANUis not lit in the display, press and  
hold the [BAND] button for 1 second or longer.  
MANUappears in the display and manual  
tuning is now available.  
2. Press and hold one of the [DIRECT] buttons  
for 2 seconds or longer to store the current  
station to that preset memory.  
2. Tune into a station.  
GUsing the LIST screen  
GQuick tuning:  
1. Press the [BAND] button and select the  
Press and hold the [d] or [a] button for 1  
desired TV band. (TV1 or TV2)  
second or longer to tune in a station.  
48  
VRX746VD  
TV Operations  
2. Touch the screen to display the menu, then  
Setting the TV area (When the  
TTX7504z is connected.)  
This function is enabled only when the panel is  
open.  
touch the [LIST] key.  
3. Touch and hold one of the [DIRECT] key for  
2 seconds or longer to store the current  
station into the preset memory.  
When you select the TV area (TV reception  
area), the TV tuner area setting changes.  
1. Touch the screen to display the menu, then  
Auto store  
Auto store selects 6 TV stations automatically  
and stores each one into a preset memory.  
touch the [SUB] key.  
2. Touch the [TV AREA] key to display a list of  
country name.  
If there are not 6 stations with good reception,  
stations previously stored in memory remain  
and only the strong stations are stored into  
memory.  
3. Touch the [COUNTRY NAME] key to select a  
desired country.  
4. Touch the [RTN] key to return the previous  
1. Press the [BAND] button and select the  
mode.  
desired TV band. (TV1 or TV2)  
2. Touch the screen to display the menu, then  
touch [LIST] key.  
3. Touch and hold the [AS] key for 2 seconds or  
longer. The stations with good reception are  
stored automatically to the preset channels.  
Preset scan  
Preset scan allows the user to view each preset  
position before it automatically advances to the  
next preset. This function is useful for searching  
for desired TV station in memory.  
1. Touch the screen to display the menu, then  
touch [LIST] key.  
2. Touch the [PS] key to start preset scan. The  
unit starts scanning each station for 7  
seconds sequentially.  
3. When the desired channel is received, touch  
the [PS] key again.  
Setting the TV diver  
This function is enabled only when the panel is  
open.  
Normally use the TV diver with the ONposition.  
You can change the reception setting for the TV  
antenna connected to the TV tuner.  
1. Touch the screen to display the menu, then  
touch [SUB] key.  
2. Touch the [TV DIVER] key to set the selected  
reception setting.  
G ON:  
Sets reception emphasizing the visual.  
G OFF:  
Sets the diver setting to OFF.  
3. Touch the [RTN] key to return to the previous  
mode.  
VRX746VD  
49  
Other Functions  
Entering titles  
Title list play  
Titles up to 10 characters long can be stored in  
memory and displayed for Radio stations, CD,  
TV stations and CD changer. The numbers of  
titles that can be entered for each mode are as  
follows.  
You can display a list of titles, then select the  
CD track, disc or broadcast station to listen to  
from that list.  
You can not display a title list with the unit in  
Seek, Preset Scan, Auto store (Tuner or TV)  
mode. Cancel those operation modes before to  
display a title list.  
Number of titles  
30 titles  
Mode  
TUNER mode  
CD mode  
TV mode  
1. Touch the screen (TV mode only).  
50 titles  
2. Touch the [LIST] key to display the LIST  
screen.  
15 titles  
A title list is displayed. The following  
functions can be carried out in a title list  
display.  
CD changer mode  
CDC655z connected  
CDC655Tz connected  
CDC1255z connected  
DCZ625 connected  
Number of titles  
60 titles  
GTUNER: A title of a station stored in the  
presets 1 to 6 or frequency is displayed;  
100 titles  
50 titles  
GCD-changer: DISC titles for discs 1 to 6  
are displayed (By changing over a display  
page in case of 12-CD changer, disc 7 to  
12 can be displayed). When there is not  
any disc in a changer, NO DISCis  
displayed.  
100 titles  
You cannot enter titles with the unit in Seek, Preset  
Scan, Auto store (TUNER or TV) mode. Cancel  
each of those operations before entering titles.  
1. Press the [FUNC] button to select the mode  
you want to enter a title (TUNER, CD, CD-  
changer or TV).  
GTV: A title of a channel stored in the  
presets 1 to 6 or a channel number is  
displayed.  
2. Select and play a CD in the CD changer or a  
CD track or tune in to a Radio station or a TV  
station for which you want to enter the title.  
3. Touch the [DIRECT] key (1 to 6) to select  
one of the items 1 to 6 and reproduce the  
selected broadcast station or disc.  
3. Touch the screen (TV mode only).  
In case of 12-CD changer, touch the [z] key  
to change over to a list display of discs 7 to  
12.  
4. Touch the [LIST] key to display the LIST  
screen.  
5. Touch the [USER TTL] key.  
4. Touch the [RTN] key again to return to the  
The title input mode display appears.  
previous mode.  
6. Touch the characters, symbols, etc. shown in  
the display to input titles.  
Changing over monitor display size  
This function is available only when the panel is  
open.  
: Centering  
CLEAR: Backspace  
: Space  
Notes:  
This function is not available while you are  
driving.  
Switch to the VISUAL/DVD player(DVD video or  
video CD)/DVD changer/TV mode you see.  
MEMO: Memory  
z(w): Scroll  
Notes:  
Up to 10 characters can be input.  
To switch the character types, touch the scroll key  
(z) at the lower left of the display.  
1. Touch the screen to display the menu, then  
touch display sizekey ([F.WIDE], etc.).  
Each time you press the [DISP] button, the  
monitor display size changes in the following  
order:  
7. Repeat the step 6 to enter the complete title.  
8. Touch the [MEMO] key for 2 seconds or  
longer to store the title into memory and  
cancel title input mode.  
F. WIDE” “CINEMA” “NORMAL” ➜  
“WIDE” F. WIDE”  
50  
VRX746VD  
Other Functions  
G F. WIDE: (full wide mode)  
Triggered audio mute for cellular  
The whole image elongates horizontally.  
G CINEMA: (cinema mode)  
telepones  
This unit requires special wiring to mute the  
audio signal automatically when a cellular  
telephone rings in the car.  
The image at both top and bottom in a  
display disappears.  
This function is not compatible with all cellular  
telepones. Contact your local authorized Clarion  
dealer for information on proper installation and  
compatibility.  
G NORMAL: (normal display)  
There is a black area at both right and left  
ends of a display. In case of normal TV  
broadcasting (4:3), the image can be shown  
without being cut or deformed.  
G WIDE: (wide mode)  
The image at right and left ends in a display  
elongates horizontally.  
Notes:  
When a normal 4:3 size image, not being a wide  
one, is viewed by displaying it fully on a wide  
monitor display in a wide mode or a full-wide  
mode, a part of the peripheral image will be  
lacking or deformed. In deference to the intention  
of producer, an original image can be viewed in a  
normal mode.  
During superimposed display, it becomes a full-  
wide mode.  
When the monitor display size mode is changed,  
only the monitor display size indication  
superimposed on the screen (NORMAL,  
WIDE, F.WIDEor CINEMA) will be changed,  
then the corresponding display size mode will be  
engaged.  
Internal amplifier cancel function  
This function is used to disable the internal  
amplifier when an external amplifier is  
connected.  
The factory default setting is OFF.  
1. Press the [ADJ] button.  
2. Touch the [AUDIO EXT.] key.  
3. Touch the [AMP CANCEL] key to select  
ONor OFF.  
GOFF: Use with the internal amplifier.  
GON: Use with the external amplifier.  
4. Touch the [ESC] key to return to the previous  
screen.  
VRX746VD  
51  
5.1 ch Surround Decoder Operations  
GDolby PL II CONTROL  
5.1 ch Surround Decoder control function  
This function is available when a 5.1 ch  
Surround Decoder (DVH940) is connected.  
This function is available only when the MUSIC  
MODE is selected for Dolby PL II. For setup  
details, see Selecting the Dolby PL II (Dolby  
Pro Logic II) type.”  
When the 5.1 ch Surround Decoder (DVH940,  
sold separately) is CeNET connected, the 5.1 ch  
Surround Decoder Control unit (DVC940, sold  
separately) cannot be used.  
3-1. Touch the [Dolby PL II CONTROL] key to  
show the submenu.  
3-2. Touch the [PANORAMA], [DIMENSION] or  
[CENTER WIDTH] key to select respective  
item.  
This section describes operation procedures only.  
For other details, refer to the owners manual  
supplied with the 5.1 ch Surround Decoder  
(DVH940).  
Requires an optional amplifier sold separately.  
1. Press the [ADJ] button to show the ADJUST  
[PANORAMA]:  
Select the ONor OFF. OFFis the  
default value.  
[DIMENSION]:  
MODE menu.  
Touch the key to make adjustments  
between 0 and 6. The default value is 3.  
[CENTER WIDTH]:  
Touch the key to make adjustments  
between 0 and 7. The default value is 3.  
GFILTER  
This function is used to select filter frequencies  
that suit the speakers that are used.  
2. Touch the [AUDIO EXT.] key.  
This function is not available for speakers whose  
SPEAKER SELsetting is set to OFF.  
3-1. Touch the [FILTER] key to show the  
submenu.  
3-2. Touch the [FRONT HPF], [CENTER HPF],  
[SURROUND HPF] or [SUB WOOFER  
LPF] key to set respective item.  
[FRONT HPF]:  
This function can be set to the following  
four settings: 50 Hz, 80 Hz, 120 Hz or  
THRGH (through). THRGHis the default  
value.  
3. Touch the required keys to make the desired  
setting.  
GSPEAKER SEL (speaker selection)  
[CENTER HPF]:  
This function determines center speaker,  
surround speaker and sub woofer connection.  
This function can be set to the following  
three settings: 50 Hz, 80 Hz and 120 Hz.  
120 Hzis the default value.  
3-1. Touch the [SPEAKER SEL] key to show  
the submenu.  
[SURROUND HPF]:  
3-2. Touch the [CENTER SP], [SURROUND  
SP] or [SUB WOOFER] key to turn  
speakers on or off depending on what  
speakers are connected.  
This function can be set to the following  
four settings: 50 Hz, 80 Hz, 120 Hz or  
THRGH (through). THRGHis the default  
value.  
The factory default setting is ON.  
[SUB WOOFER LPF]:  
The phase of the SUB WOOFERis  
reversed in the ON- setting. The default  
value is ON+.  
This function can be set to the following  
three settings: 50 Hz, 80 Hz and 120 Hz.  
120 Hzis the default value.  
52  
VRX746VD  
5.1 ch Surround Decoder Operations  
GSPEAKER GAIN  
DSF mode  
This function sets speaker output level.  
DSF effect ON/OFF  
The factory default setting is OFF.  
This function is not available for speakers whose  
SPEAKER SELsetting is set to OFF.  
1. Press the [ADJ] button and touch the  
3-1. Touch the [SPEAKER GAIN] key to show  
[AUDIO] key.  
the submenu.  
3-2. Touch the [FRONT L], [CENTER], [FRONT  
R], [SURROUND R], [SURROUND L] or  
[SUB WOOFER] key to set respective item.  
3-3. Touch the key to make adjustments in the  
range 10 dB to +10 dB in 1 dB step  
increments. The default value is 0 dB.  
GDELAY  
This function adjusts the timing of the speakers  
so that they are synchronized with front speaker  
output.  
2. Touch the [STATUS] key.  
3. Touch the [DSF] key to select ONand  
This function is not available for speakers whose  
OFF.  
SPEAKER SELsetting is set to OFF.  
4. Each time the [DSF] key is touched, the on  
3-1. Touch the [DELAY] key to show the  
and off statuses are switched alternately.  
submenu.  
5. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
Note:  
3-2. Touch the [CENTER SP] or [SURROUND  
SP] key to set respective item.  
[CENTER SP]:  
If the DSF effect is set to OFF, the adjustment  
made in DSFis not reflected in the music  
source.  
Adjustments are made in the range 0 ms to  
5 ms. The default value is 0 ms.  
[SURROUND SP]:  
Selecting the DSF type  
1. Press the [ADJ] button and touch the  
[AUDIO] key.  
Adjustments are made in the range 0 ms to  
15 ms. The default value is 0 ms.  
GDRC  
2. Touch the key for the desirable type to select it.  
This function sets the dynamic range  
compression.  
This function is not available for speakers whose  
SPEAKER SELsetting is set to OFF.  
3. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
3-1. Touch the [DRC] key to show the submenu.  
P.EQ mode  
3-2. Touch the [MAX], [STD] or [MIN] key to  
P.EQ effect ON/OFF  
select respective item.  
The default value is MAX.  
The factory default setting is OFF.  
1. Press the [ADJ] button and touch the  
4. Touch the [RTN] key, [ESC] key, or press the  
[AUDIO] key.  
[ADJ] button.  
2. Touch the [STATUS] key.  
3. Touch the [P.EQ] key to select ONand  
OFF.  
4. Each time the [P.EQ] key is touched, the on  
and off statuses are switched alternately.  
5. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
Note:  
If the P.EQ effect is set to OFF, the adjustment  
made in P.EQis not reflected in the music  
source.  
VRX746VD  
53  
5.1 ch Surround Decoder Operations  
Setting and storing P.EQ Properties  
1. Press the [ADJ] button and touch the  
[AUDIO] key.  
Output adjustment of subwoofer  
volume, center volume and balance/  
fader  
2. Touch the [P.EQ] key to show the P.EQ  
1. Press the [ADJ] button and touch the  
adjusting display.  
[AUDIO] key.  
3. Touch the key for the desirable type to select it.  
Touch the [DETAIL] key.  
The P.EQ adjustment contents are as  
follows:  
2. To make an adjustment on :  
GSubwoofer volume adjustment  
GSIGNAL  
2-1. Touch the [SUBWOOFER VOL] key to  
The factory default setting is P.NOISE.  
This function selects P. NOISEor MUSIC.  
GSPEAKER SELECT  
adjust to desirable level.  
The factory default setting is 0. (Setting  
range : 6 to 3)  
The factory default setting is FRONT.  
GCenter volume adjustment  
This function selects FRONT, CENTERor  
SURROUND.  
2-1. Touch the [CENTER VOL] key to adjust to  
desirable level.  
The factory default is 0. (Setting range : 6  
GBAND  
to 0)  
The factory default setting is BAND1.  
Select the channel to be compensated  
GBalance/Fader adjustment  
2-1. Touch the [BAL/FAD] key.  
(BAND1, BAND2, BAND3).  
Touch the [w] or [z] key to adjust the  
GFREQUENCY  
The factory default setting is 1 kHz.  
balance level.  
[w] key :emphasized the sound from the  
Select the center frequency that you want to  
compensate from the range of 18 Hz to 20  
kHz. (1/3 octave step, 31 points)  
front speakers.  
[z] key :emphasized the sound from the  
rear speakers.  
GQ  
2-2. Touch the [Å] or [Î] key to adjust the  
The factory default setting is 1.  
Set the sharpness of the Q-curve to one of  
the parameters: 1, 3, 5, 7 and 20.  
fader level.  
[Å] key : emphasized the sound from the  
left speakers.  
GGAIN  
[Î] key : emphasized the sound from the  
The factory default setting is 0.  
Adjust the gain (output level) in the range of  
6 dB to +6 dB. (1 dB step, 13 points)  
right speakers.  
3. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
4. Touch the [RTN] key, [ESC] key, or press the  
[ADJ] button.  
Selecting the Dolby PLII (Dolby Pro  
Logic II) type  
The factory default setting is OFF.  
1. Press the [ADJ] button and touch the  
[AUDIO] key.  
Touch the [Dolby PLII] key.  
2. Touch the key for the desirable type to select  
it.  
3. When the setting is finished, touch the [ESC]  
key or press the [ADJ] button to return to the  
previous mode.  
54  
VRX746VD  
12. IN CASE OF DIFFICULTY  
Problem  
Cause  
Measure  
Power does not  
turn on.  
Fuse is blown.  
Replace with a fuse of the same amperage. If the  
fuse blows again, consult your store of purchase.  
(No sound is  
produced.)  
Incorrect wiring.  
Consult your store of purchase.  
Nothing happens The microprocessor has  
Turn off the power and remove the DCP.  
when buttons are malfunctioned due to noise, Press the reset button for about 2 seconds with a  
pressed.  
etc.  
thin rod.  
Note: When the reset button is pressed, turn off the  
Display is not  
accurate.  
ACC power.  
SECURITY  
The Reset button  
When the reset button is pressed, frequencies of  
TV/radio stations, titles, etc. stored in memory are  
cleared.  
The remote  
controller does  
not work.  
Direct rays of the sun fall on When direct rays of the sun fall on the light-receptive  
the light-receptive part of the part of the remote controller, it may not work.  
remote controller.  
The batteries of the remote  
controller unit are dead or  
there is no battery in the  
remote controller unit.  
Check the batteries of the remote controller unit.  
Disc cannot be  
loaded.  
Another disc is already  
loaded.  
Eject the disc before loading the new one.  
Eject the foreign matter forcibly.  
There is a foreign matter  
already in place.  
Sound skips or is Compact disc is dirty.  
noisy.  
Clean the compact disc with a soft cloth.  
Compact disc is heavily  
scratched or warped.  
Replace with a compact disc with no scratches.  
Sound is bad  
directly after power the internal lens when the car  
is turned on. is parked in a humid place.  
Water droplets may form on  
Let dry for about 1 hour with the power on.  
Disc cannot play The view is limited.  
with the display  
Release the view limitation or change the parental  
level.  
See the subsection Setting up the parental level.  
PARENTAL  
VIOLATION”  
shown.  
VRX746VD  
55  
Problem  
Cause  
Measure  
The image is not The parking brake is not  
Check that the parking brake is applied.  
displayed.  
pulled.  
The display is  
dark.  
The brightness control is too Adjust the brightness properly.  
low.  
The operating condition is  
not good.  
The temperature inside the vehicle may be 0˚C or  
less. Set to an appropriate temperature (25˚C or so)  
and check it again.  
The headlight of the vehicle The display is made dark at night to prevent the  
is lit.  
glare (When the headlight of the vehicle is lit in the  
daytime, the display gets dark).  
The color of the  
The color is not adjusted  
Check that COL and HUE are adjusted properly.  
display is light or adequately.  
a shade of color  
is not good.  
When the VTR is Improper NTSC/PAL setting Set the NTSC/PAL properly according to the VTR.  
connected, the  
image is  
disturbed.  
When the TV  
tuner is  
connected, the  
image gets  
unclear.  
Bad receiving condition  
A radio wave may not reach sufficiently due to  
obstruction of mountains or buildings. Check it again  
at a place where a radio wave can be received  
properly.  
The TV tuner has Bad receiving condition  
a double or triple  
image.  
It may be under the influence of radio wave reflected  
by mountains or buildings. Check it again after  
changing place or direction.  
The TV tuner has Presence of jamming  
spots or stripes in  
the image.  
It may be under the influence from automobiles,  
streetcar, power cable, neon sign, and so forth.  
Check it again after changing place.  
There are red,  
green, and blue  
points in the  
display.  
This is not a failure, but a phenomenon peculiar to a  
liquid crystal panel (The liquid crystal panel is  
produced according to technology with very high  
precision. Note that, though there are effective pixels  
of 99.99% or more, pixel missing or normally lit  
pixels account for 0.01%).  
56  
VRX746VD  
13. ERROR DISPLAYS  
If an error occurs, one of the following displays is displayed.  
Take the measures described below to eliminate the problem.  
Cause  
Measure  
ERROR 2  
ERROR 3  
ERROR 6  
A CD is caught inside the CD deck and is This is a failure of CD decks mechanism  
not ejected.  
and consult your store of purchase.  
A CD cannot be played due to scratches,  
etc.  
Replace with a non-scratched,  
non-warped-disc.  
A CD is loaded upside-down inside the CD Eject the disc then reload it properly.  
deck and does not play.  
DISC ERROR A PAL format disc has been loaded.  
Remove the disc and replace with an  
NTSC format disc.  
(Only on Korea-market model.)  
ERROR 2  
ERROR 3  
ERROR 6  
A CD inside the CD changer is not loaded. This is a failure of CD changers mechanism  
and consult your store of purchase.  
A CD inside the CD changer cannot be  
played due to scratches, etc.  
Replace with a non-scratched, non-  
warped-disc.  
A CD inside the CD changer cannot be  
played because it is loaded upside-down.  
Eject the disc then reload it properly.  
For the DVD changer, refer to the Owners Manual provided with the DVD changer.  
If an error display other than the ones described above appears, press the RESET button. If the  
problem persists, turn off the power and consult your store of purchase.  
When the reset button is pressed, frequencies of radio stations, titles, etc. stored in memory are cleared.  
VRX746VD  
57  
14. SPECIFICATIONS  
FM Tuner  
LCD Monitor  
Frequency Range: 87.0 MHz to 108.0 MHz  
Usable Sensitivity: 9 dBf  
Screen Size: 7-inch wide type  
6" Width (152 mm) × 3-5/16" Height  
(85 mm )  
50dB Quieting Sensitivity: 15 dBf  
Alternate Channel Selecitivity: 70 dB  
Stereo Separation (1 kHz): 35 dB  
Frequency Response ( 3 dB): 30 Hz to 15 kHz  
Display method:  
Transmission type TN liquid crystal display  
Drive method: TFT (thin-film transistor)  
active matrix driving  
AM Tuner  
Pixels: 336,960 (1440 × 234)  
Frequency Range: 531 kHz to 1629 kHz  
Usable Sensitivity: 28 dBµV  
General  
Power source voltage:  
14.4 V DC (10.8 to 15.6 V allowable)  
DVD player  
System:  
Ground: Negative  
Digital Versatile Disc System with CDDA  
capable  
Current consumption: 4.0 A (1 W)  
Auto Antenna Rated Current: 500 mA less  
Usable discs: DVD video disc, Compact disc  
Frequency Response:  
Dimensions of the Main Unit:  
7" Width (178 mm) × 1-15/16" Height  
(50 mm) × 6-1/2" Depth (165 mm)  
Weight of the Main Unit: 2.4 kg  
Dimensions of the Remote Control Unit:  
2-1/8" Width (54 mm) × 1-1/8" Height  
(28.8 mm) × 6-1/8" Depth (155 mm)  
Weight of the Remote Control Unit:  
100 g (including battery)  
20Hz to 20 kHz (CD) ( 1 dB)  
Signal to Noise Ratio: 100 dB (1 kHz) IHF-A  
Dynamic Range: 100 dB (1 kHz)  
Distortion: 0.01%  
Audio Amplifier  
Rated power output:  
18 W × 4 (20 Hz to 20 kHz, 1%, 4 )  
Maximum power output:  
212 W (53 W × 4)  
Speaker impedance: 4 (4 to 8 )  
Input  
Audio input:  
130 60mVrms (High)  
600 80mVrms (Mid)  
840 100mVrms (Low)  
(input impedance 10 kor greater)  
Video input:  
6-3/4" (172 mm)  
7" (178 mm)  
1-15/16"  
(50 mm)  
1.0 0.2 Vp-p (input impedance 75 )  
Notes:  
Specifications comply with JEITA Standards.  
Specifications and design are subject to change  
without notice for further immprovement.  
Video output  
Video output:  
1.0 0.2 Vp-p (output impedance 75 )  
58  
VRX746VD  
VRX746VD  
Installation and Wire connection manual  
I Contents  
1. BEFORE STARTING ............................................................... 59  
2. PACKAGE CONTENTS ........................................................... 59  
3. GENERAL CAUTIONS ............................................................ 60  
4. CAUTIONS ON INSTALLATION .............................................. 60  
5. INSTALLING THE MAIN UNIT ................................................. 61  
6. REMOVING THE MAIN UNIT .................................................. 63  
7. CAUTIONS ON WIRING.......................................................... 63  
8. WIRE CONNECTION .............................................................. 64  
9. SAMPLE SYSTEMS ................................................................ 67  
1.  
BEFORE STARTING  
1. This set is exclusively for use in cars with a  
negative ground 12 V power supply.  
2. Read these instructions carefully.  
3. Be sure to disconnect the battery “-”  
terminal before starting. This is to prevent  
short circuits during installation. (Figure 1)  
Car battery  
Figure 1  
2.  
PACKAGE CONTENTS  
1 Main unit  
5
Bag for accessories (No. 2)  
Hook plate ................................................... 2  
Cord clamp  
2 Manuals  
Owners manual & Installation manual  
Warranty card  
Rubber cap  
3 Power supply lead  
Special screw  
4
Bag for accessories (No. 1)  
6 Universal mounting bracket  
7 Remote control unit  
8 Battery  
Flat head screw (M5 × 8) ............................ 4  
Sems hexagonal bolt (M5× 8) ..................... 5  
Electro tap  
(for remote control unit)  
9 Outer Escutcheon  
0 DCP Case  
Machine screw (M4× 3)............................... 4  
VRX746VD  
59  
3.  
GENERAL CAUTIONS  
1. Do not open the case. There are no user  
serviceable parts inside. If you drop anything  
into the unit during installation, consult your  
dealer or an authorized CLARION service  
centre.  
2. Use a soft, dry cloth to clean the case. Never  
use a rough cloth, thinner, benzine, or  
alcohol, etc. For tough dirt, apply a little cold  
or warm water to a soft cloth and wipe off the  
dirt gently.  
4.  
CAUTIONS ON INSTALLATION  
1. Prepare all articles necessary for installing  
the main unit before starting.  
5. Use the enclosed screws for installation.  
Using other screws can cause damage.  
(Figure 4)  
2. This model is used with the liquid crystal  
panel slid forwards (shell loading system).  
On some types of cars, the liquid crystal  
panel may touch the dashboard or shift lever,  
in which case it cannot be installed. Check  
that the set will not hamper operation of the  
shift lever before choosing the place of  
installation.(Figure 2)  
Chassis  
Chassis  
Damage  
Max. 8 mm (M5 screw)  
Figure 4  
Dashboard  
6. The source unit has mounting screw holes  
for NISSAN (N marks) and TOYOTA (T  
marks) vehicles.  
T
N
T
Shift lever  
Shift lever  
(check that it does not  
touch the LCD.)  
Figure 2  
N
T
N
3. Install the unit within 30° of the horizontal  
plane. (Figure 3)  
Figure 5  
Max. 30˚  
Figure 3  
4. If you have to do any work on the car body,  
such as drilling holes, consult your car dealer  
beforehand.  
60  
VRX746VD  
5.  
INSTALLING THE MAIN UNIT  
I Universal Mount  
1. Place the universal mounting bracket into the  
instrument panel, use a screwdriver to bend  
each stopper of the universal mounting  
bracket inward, then secure the stopper as  
shown in Figure 6.  
2. Wire as shown in Section 8.  
Notes:  
3. Insert the main unit into the universal  
mounting bracket until it locks.  
1) Some car models require special mounting kits  
for proper installation. Consult your Clarion  
dealer for details.  
2) Fasten the front stopper securely to prevent  
the main unit from coming loose.  
4. Mount the outer escutcheon so that all the  
hooks are locked.  
• Console opening dimensions  
Rear fastening hole (of vehicle)  
Instrument panel  
7-3/16" (182 mm)  
Hole  
Hole  
Stoppers  
Special Screw  
Screwdriver  
Rubber cap  
Universal mounting bracket  
Stoppers  
Main unit  
2-Spring  
Outer escutcheon  
Note:  
Set the outer escutch-  
eon so that its metallic  
part on the back side  
fits the upper edge of  
the main unit.  
Figure 6  
VRX746VD  
61  
I Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles)  
This unit is designed for fixed installation in the  
dashboard.  
direction of arrow to remove it. Repeat the  
same for the other side to remove the  
springs from the both sides. (Figure 7)  
If the vehicle is equipped with a factory-installed  
radio, install the main unit with the parts and  
screws marked (). (Figure 8)  
If the vehicle is not equipped with a factory-  
installed radio, obtain an installation kit to install  
the main unit in the following procedure.  
2. Secure the mounting brackets to the chassis  
as shown in Figure 8. Holes are pre-tapped  
for TOYOTA and NISSAN vehicles;  
modification, such as drilling new holes, of  
the mounting brackets may be required for  
other models.  
1. Remove the screws from both side of the  
main unit. Then, at either side, lift the leaf  
spring until the engaging claws are released  
from the holes, and slide the spring to the  
3. Wire as shown in Section 8.  
4. Secure the unit in the dashboard, and then  
reassemble the dashboard and the centre  
panel.  
2-Screw  
Engagin claw  
Main Unit  
2-Spring  
Screwdriver  
Figure 7  
Mounting bracket  
(1 pair for the left and right sides)  
4-Hexagonal screw (M5 × 8)  
Main Unit  
Pocket  
Note 2  
Centre Panel (Note 1)  
: The screws with this mark are  
enclosed in this set.  
#:The parts and screws with this mark  
are used to install radio or included in  
the installation kit.  
Figure 8  
Note 1: In some cases, the centre panel may  
require some modification (trimming,  
filling, etc.).  
Note 2: If a hook on the installation bracket  
interferes with the unit, bend and flatten it  
with a nipper or a similar tool.  
62  
VRX746VD  
6.  
REMOVING THE MAIN UNIT  
1. When the rear of the main unit has been  
secured with the method shown in Figure 6  
unfasten the special screw.  
pull the main unit out by the hook plate.  
(Insert both the right and left edges of the  
hook plate.) (Figure 9)  
2. Remove the outer escutcheon.  
Note: Keep the hook plate. You cannot remove the  
3. Insert the hook plate between the spring and  
the universal mounting bracket, fit tab B of  
the spring into hole A of the hook plate, then  
main unit without disengaging the hook plate.  
Instrument panel  
Universal mounting bracket  
2-Hook plate  
Main  
Unit  
Spring  
Outer escutcheon  
A
B
Figure 9  
7.  
CAUTIONS ON WIRING  
Note: There are various types of fuse holder. Do  
not let the battery side touch other metal  
parts.  
1. Be sure to turn the power off before wiring.  
2. Be particularly careful where you route the  
wires.  
Keep them well away from the engine, and  
exhaust pipe, etc. Heat may damage the  
wires.  
CAUTION  
After the connection, fix the lead by a clamp or  
insulation tape for protection.  
3. If the fuse should blow, check to see if the  
wiring is correct.  
If it is, replace the fuse with a new one with  
the same amperage rating as the original  
(15A FUSE).  
Fuse (15A FUSE)  
4. To replace the fuse, remove the old fuse of  
the power supply lead and insert the new  
one. (Figure10)  
Fuse holder  
Figure 10  
VRX746VD  
63  
8.  
WIRE CONNECTION  
Radio antenna jack  
Optical output connector  
CeNET  
terminal  
Red  
Gray  
Right  
left  
Front audio output terminal (*2)  
Rear audio output terminal (*2)  
Non fader output terminal  
White  
Red  
Black  
Right  
left  
White  
Red  
Right  
left  
Purple  
White  
Yellow  
Video output terminal (*3)  
Yellow  
Yellow  
TV tuner input terminal  
DVD changer input terminal  
Yellow  
Video  
White  
Red  
Audio (left)  
Visual input terminal  
Audio (right)  
1: Connecting the PHONE MUTE Terminal  
The lead included with the unit must be connected to the specified position of the vehicles  
connector in order to use the triggered audio mute for cellular telephonesfunction.  
Note : Before making any installation, disconnect the car battery - (negative) cable.  
2: Connect to a separately sold external amplifier with a separately sold RCA cord (L, R).  
3: Connect to a Rear View Monitor (sold separately) for the rear seat.  
64  
VRX746VD  
Yellow  
Black  
+12V main power  
Ground  
Purple  
Rear right +  
Purple/Black  
Grass-green  
Rear right -  
Parking brake  
Glay  
Front right +  
Glay/Black  
Front right -  
White  
Front left +  
White/Black  
Front left -  
Green  
Rear left +  
Green/Black  
Rear left -  
Blue/White  
Amplifier turn-on lead  
Illumination  
Orange/White  
Red  
+12V accessory  
Brawn  
Blue  
Phone mute (*1)  
Auto antenna  
VRX746VD  
65  
I Connecting the Accessories  
Connection to the external amplifier  
The external amplifier can be connected unless the 5.1ch Surround Decoder is connected. For  
detailed information, refer to the instruction manual of the 5.1ch Surround Decoder.  
Connection to the CCD camera for vehicle  
The CCD camera for vehicle can be connected to CCD terminal on the tuner amp unit. For detailed  
information, refer to the instruction sheet or manual for the CCD camera.  
Notes:  
• A power supply box (sold separately) is required for connection of the main unit and the CCD camera.  
• The power supply box for camera CAA147 cannot be used. Please use the CAA188 instead.  
If the specified lead of the cellular phone is connected to the phone mute  
lead of the source unit, the audio mute is available when the cellular  
telephone is used.  
TV Tunner  
When the TV TUNER is to be connected, connect the CeNET connector and RCA PIN (yellow). For  
detailed information, refer to the instruction manual of the TV TUNER.  
Parking brake lamp  
I Connecting the parking brake lead  
Connect the lead to parking brake lamp earth  
+ lead to battery  
in the meter panel.  
Connect these three leads.  
Notes:  
- cord  
• Connecting the parking brake lead to lamp earth  
allows you to watch TV/VTR/DVD video/video  
CD when the parking brake is engaged.  
• When the parking brake lead is not connected,  
the monitor will stay off.  
parking  
brake signal  
lead  
Parking brake lead  
(bright green)  
Parking brake  
66  
VRX746VD  
9.  
SAMPLE SYSTEMS  
I Sample System 1  
VRX746VD  
Front  
Speakers  
RCA cable  
(sold separately)  
Rear  
Speakers  
Visual input  
RCA video cable (sold separately)  
Yellow  
VIDEO OUT  
Rear View  
Monitor  
(VMA5894/  
VMA7194)  
Yellow  
Yellow  
DVD A/C IN  
TV IN  
CeNET cable  
(included the  
TV tuner)  
VTR  
RCA video cable  
(included the TV tuner)  
CCD  
TV tuner  
(TTX7501z  
/TTX7504z)  
Camera  
(CC425E)  
Conector cable  
(included the CC425E)  
CeNET cable  
CeNET Cable  
(included the Changer)  
CeNET Y-adapter  
(CCA-519-601,  
sold separately)  
Ferrite clamp  
(Included the DVD changer)  
CeNET DVD Changer  
CD Changer  
(DCZ625)  
(VCZ625)  
Set the [CeNET/STAND ALONE]  
switch to the [CeNET] position.  
STAND  
CeNET  
ALONE  
VRX746VD  
67  
I Sample System 2  
VRX746VD  
RCA cable  
(sold separately)  
VTR  
Visual input  
(Glay)  
Non fader  
output  
Front  
Speakers  
CeNET cable  
(included  
RCA video cable  
(included the TV tuner)  
the TV tuner)  
RCA cable  
(sold separately)  
Rear  
Speakers  
TV Tuner  
(TTX7501z  
/TTX7504z)  
4-Channel  
Amplifier  
(APA4320)  
RCA cable  
(included the  
DVH940)  
CeNET cable  
(included the  
DVH940)  
RCA cable  
(sold separately)  
Center speaker  
built-in amplifier  
(SRK5)  
5.1 ch Surround  
Powered sub-woofer  
built-in amplifier  
(SRV303)  
(Black)  
Decoder  
(DVH940)  
RCA cable (sold separately)  
CeNET cable  
(included the VCZ625)  
Ferrite clamp  
(Included the DVD changer)  
CeNET DVD Changer  
(VCZ625)  
Set the [SLAVE/STAND ALONE]  
switch to the [SLAVE] position.  
STAND  
SLAVE  
ALONE  
(Glay)  
Digital optical fiber cable  
(
DCA-005/008, sold separately)  
Set the [CeNET/STAND ALONE] switch to  
the [CeNET] position.  
STAND  
CeNET  
ALONE  
Note:  
When the DVD changer (VCZ625) is connected  
via optical cable, no sound will be output if AUDIO  
OUT is switched to ANALOG on the changers  
GENERAL SETUPmenu.  
68  
VRX746VD  

ATN 6800c User Manual
Audiovox AV 970 User Manual
Audiovox HR7011PKG User Manual
Bravetti FP200C User Manual
Canon Camcorder HD Camcoder User Manual
Canon SUPER 150U User Manual
Directed Audio D2400 User Manual
Hamilton Beach Blender 49970 User Manual
Harman Coal Stoker VF3000 User Manual
JVC Car Speaker CS HX636 User Manual