Owner’s manual
Mode d’emploi
Manual de instrucciones
DSC920S
SIRIUS SATELLITE RADIO
RECEIVER CONTROLLER
CONTRÔLEUR DE RÉCEPTEUR
RADIO SATELLITE SIRIUS
CONTROLADOR DEL
SINTONIZADOR SIRIUS DE
RECEPCIÓN RADIO VÍA
SATÉLITE
3.CONTROLS
[
]
[
]
P-M
SS
[
]
[
]
[
]
BAND
DISP
SAT
[
]
CAT
[
]
SCAN
Names of the Buttons and their Functions
[SAT] button
• Used to turn the power on or off.
[w], [z] button
• Used to move the preset channel up or down.
• Used to move the category up or down in the
Category selection mode.
[BAND] button
• Used to switch the reception band.
• Used to switch the item adjustment or the item
in the Adjust mode. (Contrast adjustment,
SIRIUS ID display switching)
• Used to switch the Tuning mode (seek/
manual) when pressed and held for 1 second
or longer.
[P-M] button
• Used to enter the Preset memory mode.
[CAT] button
• Used to turn the Category selection mode on
or off.
• Received channels are stored in the preset
channels when the button is pressed and held
for 2 seconds or longer.
[SCAN] button
• Used to perform the category scan.
[SS] button
• Used to switch the screen saver.
• Used to perform the preset scan when the
button is pressed and held for 1 second or
longer.
OFF ➜ SS1 ➜ SS2 ➜ OFF……
• Used to enter the Adjust mode when pressed
and held for 1 second or longer. When
pressed, the Adjust mode is terminated.
[DISP] button
• Used to switch the Text mode.
• The text display in the operation status indica-
tion scrolls when the button is pressed and
held for 1 second or longer.
[a], [d] button
• Used to move the channel up or down.
• Used to search up or down the channel in the
Category selection mode.
• Used to switch the adjustment item in the Ad-
just mode.
• Used to move the channel faster when kept
pressed.
DSC9 2 0 S
3
Display Items
Preset channel indication (1 to 6)
SAT(satellite) indication
Operation status
indication
PRESET indication
CAT(category) indication
BAND
indication
MANU (manual) indication
SCAN indication
SAT (satellite) indication:
• Lights in the SIRIUS mode, goes off in some
other mode or when the power is turned off.
MANU (manual) indication:
• Lights when tuning is performed in the Manual
mode.
Operation status indication:
• Station names, etc. are displayed.
SCAN indication:
• Lights when category scan is performed or
when preset scan is performed.
• Display examples
CH 051
: channel No.
: preset scan
CAT (category) indication:
• Lights when the unit enters the Category se-
lection mode or when category scan is per-
formed.
P SCAN
CONTRAST : displayed when the contrast
adjustment is selected in the
Adjust mode.
PRESET indication:
• Lights when the unit enters the Preset
memory mode.
ESN>>
: displayed when the SIRIUS ID
is confirmed.
CAT SEL
LINKING
: displayed when the Category
selection mode is selected.
: displayed when a channel is
being tuned in (no signal is yet
received).
NOSIGNUP : displayed when a channel not
covered by your contract is se-
lected.
UPDATING : displayed when the receiver is
turned on or after a reset.
INVLD CH : a channel without a broadcast
has been selected.
BAND indication:
• Lights when the band (“SAT1”, “SAT2” or
“SAT3”) is being received in the SAT mode.
4
DSC9 2 0 S
4.OPERATIONS
Turning the power on/off
1. Press the [SAT] button to turn the power on/
3. Press and hold the [a] or [d] for 1 second
or longer.
The receiver moves to seek channels below
or above the current channel and the chan-
nel found when either button is released is
received.
off.
When the power is turned on, “SAT” is dis-
played in the Operation status indication and
then the display is changed to the channel
being received.
● Seek tuning
Only channels that can be received are selected
while channels without broadcasts and channels
not covered by the contract are automatically
skipped.
Verifying your Sirius ID
1. Press and hold the [SS] button for 1 second
or longer to enter the Adjust mode.
1. Press the [a] or [d] button.
2. Press the [a] or [d] to select the “ESN
The receiver seeks the next available chan-
nel below or above the current channel.
>>”.
∗ When the unit enters the SIRIUS ID display
mode, “ESN>>” is displayed and then the dis-
play is changed to the high-order 6 digits of
the SIRIUS ID (“012345 z”) in the Operation
status indication.
2. Press and hold the [a] or [d] button.
The receiver moves to seek channels below
or above the current channel. If the channel
found when either button is released is avail-
able that channel is received. Otherwise,
seeking continues until an available channel
is found.
3. Press the [z] button to change the low-or-
der 6 digits of the SIRIUS ID (“678901 w”).
∗ To display the high-order 6 digits of the
SIRIUS ID again, press the [w] button.
4. Press the [a] or [d] button to return the
Preset memory
previous mode.
3 bands are available for preset memory and 6
channels for each band, a total of 18 channels
can be stored in memory.
Selecting a band
1. Press the [BAND] button to select a band.
The indication concerning the preset memory is
displayed both in the BAND indication for the
band being received (“SAT1”, “SAT2”, or
“SAT3”) and in the Preset channel indication for
the preset number.
BAND indication (“SAT1”, “SAT2” or “SAT3”)
is light in the display.
Tuning mode
There are two channel selection modes: seek
mode and manual mode.
● Recalling a preset station
1. Press the [w] or [z] button to recall a pre-
set station. Each time the button is pressed,
preset stations are recalled in a sequential
order.
● Manual tuning
Any channel including channels without broad-
casts and channels not covered by the contract
can be selected during manual tuning.
∗ When the [P-M] button is pressed and the Pre-
set memory mode is engaged, preset stations
cannot be recalled.
1. Press and hold the [BAND] (BND) button for
1 second or longer.
∗ When the button is pressed, the sound is
muted and reception channel data are dis-
played in the Operation status indication in the
following order.
∗ This changes the seek mode to manual mode
and the “MANU” indicator on the display lights.
When this operation is performed in manual
mode, the seek mode is engaged and the
“MANU” indicator on the display goes off.
Channel number (for example “CH 051”) ➜
abbreviated 8-digit channel name ➜ returned
to the original display mode
Notes:
• The receiver automatically reverts to the seek
mode when the [a] or [d] button is not used for
7 seconds in the manual mode.
2. Press the [a] or [d] button. The receiver
moves to channels above or below the cur-
rent channel one by one.
DSC9 2 0 S
5
Operations
● Manual memory
Receiving stations selected by
category
1. Press the [CAT] button to enter the category
selection mode. CAT indication is light in the
display.
1. Select a channel to be memorized.
2. Press the [P-M] button to enter the Preset
memory mode.
∗ The reception channel number (“CH 051”) in
the Operation status indication blinks and the
PRESET indication light.
2. Press the [w] or [z] button to select a cat-
egory.
3. Press the [w] or [z] button to select a pre-
3. Press the [a] or [d] button to tune in a sta-
set number to be memorized.
tion.
∗ The selected preset number is displayed in
the Preset channel indication.
Notes:
• When the category selection mode is entered, the
category of the last received channel is displayed
first.
• The category selection mode is canceled when
no channel with the selected category can be
found.
• Press the [a] or [d] button within 7 seconds af-
ter a channel has been set to continue seeking
channels up or down. The category selection
mode is canceled and normal reception is re-
sumed if no operation is performed for 7 seconds.
4. Press and hold the [P-M] button for 2 sec-
onds or longer to store the channel being re-
ceived in memory.
∗ If the [P-M] button is released within less than
2 seconds, preset memory is cancelled and
the Preset memory mode is terminated.
Scan function
There are two scan modes: a category scan
mode and a preset scan mode.
During scanning channels are displayed in ab-
breviated form and the display mode cannot be
switched.
Switching the text display
1. Press the [DISP] button. Each time the
[DISP] button is pressed, the item changes in
the following order:
● Category scanning
channel number ➜ channel name (long) ➜
title ➜ artist ➜ category ➜ R-TEXT
∗ When the [DISP] button is pressed while the
Screen saver mode is engaged, the displayed
text cannot be switched. If this happens, re-
lease the Screen saver mode and scroll the
displayed text again.
In a category scan, broadcast channels in the
same category as the current channel are se-
lected about every 10 seconds.
1. Press the [SCAN] button to start a category
scan.
2. Press the [SCAN] button to cancel a cat-
egory scan.
∗ If the reception channel is changed, the dis-
play changes in the order of channel number
➜ channel name (short) and then the original
display mode is resumed.
Note:
• Category scanning is not available when no cat-
egory is defined for the current channel.
● Preset scan
∗ When there is no text information, the indica-
tion “
--------” will appear on the display.
A preset scan scans the channels (up to 18
channels) stored in the preset memory about
every 10 seconds.
About the scrolling of the displayed text
Scrolling is performed once when the title being
selected is changed or when the [DISP] button
is pressed and held for 1 second or longer.
1. Press and hold the [SCAN] button for 1 sec-
ond or longer to start a preset scan.
2. Press the [SCAN] button to cancel a preset
scan.
∗ Scrolling is not performed when a channel number,
abbreviated channel name or category is displayed.
6
DSC9 2 0 S
Operations
Switching the screen saver
1. Press the [SS] button to switch the screen
saver. Each time the button is pressed, the
screen saver is switched in the order of OFF
➜ SS1 ➜ SS2 ➜ OFF.
∗ If the screen saver is turned on and the button
operation is performed, the screen saver
mode is released.
After information corresponding to the button
operation is displayed for 30 seconds, the
screen saver displayed is returned.
When “OFF” is selected, the display is not lit.
(only with backlight)
∗ If some other mode than SIRIUS mode is se-
lected with the system wire bound using
CeNET, the set screen saver works.
Adjusting the display contrast
You can adjust the display contrast to match the
angle of installation of the unit.
∗ The factory default setting is “4”. (Adjustment level :
1 to 7)
1. Press and hold the [SS] button for 1 second
or longer to enter the Adjust mode.
2. Press the [w] or [z] to adjust the contrast.
3. Press the [SS] button to return to the previ-
ous mode.
DSC9 2 0 S
7
5.INSTALLATION
Before Installation
Power supply cord connection
1. This set is exclusively for use in cars with a
negative ground, 12 V power supply.
Connect the connection cable securely.
Connect the L-shaped side of the connection
cable to the terminal of the Sirius Satellite Radio
(DSH920S).
2. Read these instructions carefully.
3. Be sure to disconnect the battery “–” terminal
before starting. This is to prevent short cir-
cuits during installation. (Figure 1)
Note:
For other connections, refer to the Owner’s manual
provided with the Sirius Satellite Radio (DSH920S).
Car battery
Fig 1
Accessories
1 Owner’s manual .......................................... 1
2 Warranty card.............................................. 1
3 Power suply cord......................................... 1
4 Connection cord .......................................... 1
5 Parts bag.......................................................
• Cord holder ................................................ 2
• Velcro tape (large A) .................................. 2
• Velcro tape (small B) .................................. 2
4
3
8
DSC9 2 0 S
Installation of the Control unit
■ Installing location
Dashboard
Place the Control unit on the passenger’s seat
or stick the Velcro tape (large A) to the center
console.
∗ Before sticking the Velcro tape, clean the sticking
surface.
Velcro tape
(large A)
∗ Choose a location where the driving of a car is not
hindered and the reception of the signals from the
remote control unit is ensured as well (Figure 2).
Fig 2
Velcro tape
(small B)
■ How to install the Control unit
When installing the Control unit, use the Velcro
tape (small B) to secure it (Figure 3).
∗ Before sticking the Velcro tape, clean the sticking
surface.
∗ To secure the cord, use the cord holder by sticking
it to the center console, etc. (Figure 4).
Control unit
Fig 3
Notes:
Do not leave the Control unit at a location (dash-
board, etc.) where the temperature goes high. Oth-
erwise, the unit may be deformed or damaged.
UP
160
55
117
Cord holder
How to install the Control unit (in case of
using screws)
Fig 4
∗ Screws are not enclosed with unit.
∗ Be sure to check the screw length. (M3 x 6mm
MAX)
DSC9 2 0 S
9
10
DSC9 2 0 S
|