User’s manual
page-11
B) Programming Tax via “Flat Tax” procedure (No break point)
3 Setting the Time and Date
CAL
X
PCR-T265/T275 Quick start guide
REG
Z
CAL
X
1. Turn the PGM key to the PGM position.
Turn the key switch to “PGM” position.
REG
OFF
RF
OFF
Z
IMPORTANT: FOR PROGRAMMING ASSISTANCE PLEASE CALL
TOLL FREE
Setting the time.
RF
2. Enter the number 3, followed by the k key.
Example: 1:18PM = 1318
PGM
1-800-638-9228
P appears in mode display
Zk
PGM
3. Enter 0125 (for tax table 1) followed by the k key. (Enter 0225 for
User’s manual
page-9
• Enter 4 digits/ • 24 hour format
ZCZ<h
1 InitializeYour Cash Register
tax table 2)
Hour
Minute
(to end the time setting)
y
4. Enter your tax rate, followed by the p key. Example: For 6%
1. Un-pack your cash register, insert the PGM key and turn to the
“OFF” position.
Setting the date.
enter the number 6. For 5.75%, enter 5.75
CAL
X
5. Enter 5002, followed by the p key.
Example: March 19, 2004 = 040319
REG
Z
P appears in mode display
Zk
6. Press the k key to end tax programming.
OFF
PGM
• Enter 6 digits/ • Enter last 2 digits for year set (2004 → 04)
?V?CZ>h
Example: Set Colorado state tax 5.25%
RF
(to end the date setting)
Year
Month
Day
y
PGM
P appears in mode display
Ck
COLORADO
5.75%
Program code number for tax table 1
5.75% tax rate
User’s manual
page-12,17
?ZXBk
B"MBp
B??Xp
k
2. Install the 58mm thermal paper roll as illustrated and close printer
cover.
4 Setting Tax rates and status
5.75
50 for round off and 02 for Add-on
(to end the setting)
5002
Tax rates
A) If you are in an area that uses a tax table for tax calculation,
Press the { key and select 02 for tax table programming and
follow the instruction.
Tax status
Your cash register is pre-programmed below.
a(Department-1): non tax
s(Department-2): taxable 1
If you need other than this setting for the Department and PLUs,
1. Issue “Help directory report”.
ENTER NUMBER THEN
PRESS <HELP> KEY.
3. Plug the power cord of the ECR into an AC outlet.
The initialization receipt is issued.
{
please refer user’s manual page-17.
01.HOW TO PROGRAM
DATE AND TIME?
User’s manual
page-16, 35
02.HOW TO PROGRAM
TAX TABLE?
Select 02 (Tax table programming).
5 Daily Management Report
00-00-2000 00:00
0001
(C) 2003 by CASIO
COMPUTER CO.,LTD.
All rights reserved.
V.3965
Read report;
CAL
X
REG
OFF
RF
Z
02.HOW TO PROGRAM
TAX TABLE?
2. Issue “Tax table index report”.
Turn the key switch to the X position and
press pkey.
INI.••••••••••••••••1 00
REGCAL
X
p
•SELECT YOUR STATE AND
ENTER NUMBER THEN
PRESS <HELP> KEY.
Z
X{
Set the key switch to “REG” mode.
OFF
PGM
Select your state.
0101:ALABAMA
0201:ALASKA
0301:ARIZONA
0401:ARKANSAS
901:
RF
Reset report;
PGM
X
CAL
REG
OFF
RF
Z
5001:WISCONSI
5101:WYOMING
Turn the key switch to the Z position and
press p key.
User’s manual
page-9
2 Load the memory protection batteries
p
PLEASE SELECT YOUR
DISTRICT NUMBER FROM
BELOW TABLE.
PGM
1. Open the platen arm.
3. Issue “State tax table code report”.
2. Open the battery compartment cover.
3. Load 3 new SUM-3 (“AA”) type batter-
ies into the compartment. Be sure that
the plus (+) and minus (-) ends of
each battery are facing in the direc-
tions indicated by the illustrations
inside the battery compartment.
4. Slide the memory protection battery
compartment cover back into place.
5. Replace the printer paper and printer
cover.
For more detailed report information, refer user’s manual.
1)TURN MODE KEY TO PGM.
?Z?Z{
2)3<SUBTOTAL>
3)025<SUBTOTAL>
SET TABLE1
For more specific programming options and operating procedures,
that will maximize the benefits of your new cash register, please refer
to you user’s manual or call 800/638-9228 for further assistance.
Thank you for your Casio purchase.
Follow these steps.
4)XXXX <CASH>KEY.
SET TABLE2(IF NECESSARY)
5)XXXX <CASH>KEY.
6)<SUBTOTAL>
XXXX IS DISTRICT NUMBER
ALABAMA
0101: 4%
State
0102: 4.5% State & Local
0103: 5%
0111: 9%
State & Local
State & Local
Replace memory protection batteries at least once every year.
|