Canon EF Lens 5125B002 User Manual

EF500mm f/4L IS II USM  
EF600mm f/4L IS II USM  
ENG  
Instructions  
Safety Precautions  
Handling Cautions  
Safety Precautions  
OO If the lens is taken from a cold environment into a  
warm one, condensation may develop on the lens  
surface and internal parts. To prevent condensation  
in this case, first put the lens into an airtight plastic bag  
before taking it from a cold to warm environment. Then  
take out the lens after it has warmed gradually. Do the  
same when taking the lens from a warm environment  
into a cold one.  
OO Do not look at the sun or a bright light source  
through the lens or camera. Doing so could result in  
loss of vision. Looking at the sun directly through the  
lens is espechazardous.  
OO Do not point lens or camera at the sun or  
photogh itis is because the lens concentrates  
te sun’s rn when the sun is outside the image  
r when sting with backlight, which could cause  
tion or fir
r it is attad to the camera or not, do not  
the lens under the sun without the lens cap  
ached. This is to prevent the lens from concentrating  
tsun’s rays, which could cause a fire.  
OO Do not leave the lens in excessive heat such as in a car  
in direct sunlight. High temperatures can cause the  
lens to malfunction.  
OO Wthe lens is mounted on a camera, be sure to also  
hold the camera by the lens, including when mounting  
on a tripod. Only holding by the camera could result in  
scratches on the camera body or the lens itself. The lens  
may also detach from its mount and fall, causing injury.  
OO Do not use a strap attached to the camera. The mount  
may break, resulting in the lens falling off and causing  
injury or in scratches on the camera. Be sure to use the  
camera with a dedicated strap attached correctly to the  
strap mount on the lens.  
Conventions used in this instruction  
Warning to prevent lens camera malf
or damage.  
Supplementary notes on ng the leand  
taking pictures.  
OO Do not stand on top of the lens case. You may fall and  
injure yourself.  
OO Do not pile lens cases on top of one another as they  
may fall and cause injury.  
ENG-2  
Safety Precautions  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1) This  
device may not cause harmful interference, and (2) this  
device must accept any interference received, including  
interference that may cause undesired operation.  
Do not make any changes or modifications to the equipment  
unless otherwise specified in the instructions. If such changes  
or modifications should be made, you could be required to  
stop operation of the equipment.  
This Class B digital apparatus complies with Canadian ICES-  
003.  
This equipment has been tested and found to comply with  
the limits for a class B digital device, pursuant to part 15  
of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a  
residential installation. This equipment generates, u
can radiate radio frequency energy and, if not inst
used in accordance with the instructions, may cau
interference to radio communications.  
However, there is no guarantee thaterference wi
occur in a particular installation. If equipment doe
harmful interference to radio or teleon reception, whic
can be determined by turning the eqment off aon, the  
user is encouraged to try to correct thterferenby one or  
more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and  
receiver.  
• Consult the dealer or an experienced radio/TV technician  
for help.  
ENG-3  
Nomenclature  
Focusing ring (6)  
Distance scale (14)  
Hood mount (14)  
Orientation locking knob (17)  
Security slot (covered) (17)  
Strap mount (5)  
Drop-in filter (18)  
Playback ring  
(9)  
Rubber ring (5)  
AF stop button  
(7)  
Contacts (5)  
Image stabilizer mode selector sw(11)  
Image stabilizer switch (→ 11)  
Focus preset button (8)  
Lens mount index (5)  
Focusing distance range  
selector switch (6)  
Focus preset switch (8)  
Tripod mount (17)  
Focus mode switch (6)  
OO The illustrations used in the explanations in this manual show the EF500mm f/4L IS II USM, but the  
EF600mm f/4L IS II USM is used in the same way.  
OO For detailed information, reference page numbers are provided in parentheses (**).  
ENG-4  
1. Mounting and Detaching the Lens  
See your camera’s instructions for details on  
mounting and detaching the lens.  
The lens mount has a rubber ring for enhanced  
dust- and water-resistance. The rubber ring may  
cause slight abrasions around the camera’s lens  
mount, but this will not cause any problems. If the  
rubber ring beomes worn, it is replaceable by a  
Canon ServicCenter at cost.  
chinthe strap  
OOAfter detaching the lens, place the lens with  
the rear end up to prevent the lens surfa
contacts from getting scratched.  
OOIf the contacts get soiled, scratched, or
fingerprints on them, corron oulty  
connections can result. Thcamera and le
may not operate properly.  
OOIf the contacts get soiled oave fingents on  
them, clean them with a soft th.  
OOIf you remove the lens, cover it dust cap.  
To attach it properly, align the lens mount index  
and the index of the dust cap as shown in  
the diagram, and turn clockwise. To remove it,  
reverse the order.  
Thread the end of the strap through the strap  
mount on the lens and then back through the  
clasp on the strap. Pull the strap tight and check  
that there is no slack in the clasp.  
ENG-5  
2. Setting the Focus Mode 3. Switching the Focusing  
Distance Range  
To shoot in autofocus (AF) mode, set the focus  
mode switch to AF.  
set the fosing distance range with a  
To shoot in manual focus (MF) mode, set t
sw. By setting a suitable focusing distance  
focus mode switch to MF, and focus by
ranthe actual autofocusing time will be  
the focusing ring. The focusing ring alw
hort
works, regardless of the focue.  
To shoot in power focus (PFmode, set th
focus mode switch to PF whn the focus pre
switch (p. 8) is at OFF.  
Operating the playback ring enles fos  
change at a set speed. This is a ul feature  
for changing focus when shooting movies.  
Lens  
Ranges  
FULL  
3.7 m/12.14 ft. – 10 m/32.81 ft.  
10 m/32.81 ft. –  
FULL  
EF500mm f/4L IS II USM  
4.5 m/14.76 ft. – 16 m/52.49 ft.  
16 m/52.49 ft. – ∞  
EF600mm f/4L IS II USM  
After autofocusing in ONE SHOT AF mode, focus  
manually by pressing the shutter button halfway  
and turning the focusing ring. (Full-time manual  
focus)  
ENG-6  
4. AF Stop Button  
The AF stop function also works in AI Servo AF  
mode.  
Angle positioning of the AF stop button is  
adjustable by a Canon Service Center at cost.  
OOWith he E630/600, RT, A2/A2E/5, or 10S/10  
set to ervo AF mode and continuous  
ooting, ill not resume even after you  
o of the stop button. Press the shutter  
se button fway to resume AF.  
During autofocus operation, you can press the  
AF stop button to temporarily pause autofocus.  
h the EOS A2/A2E/5 and 10S/10 set to the  
Sports mode, AF will not resume even after you  
t go of the AF stop button. Press the shutter  
rease button halfway to resume AF.  
If the shutter button is still pressed halfwan  
the AF stop button is released, autofocu
continue as before.  
OOYou can change the functions of the AF stop  
button using the camera’s Custom Function. For  
details, please refer to the camera’s instructions.  
ENG-7  
5. Focus Preset  
By presetting any focusing distance, you can instantly focus at that point even while you are  
shooting a different subject. This function operates in any of the AF, PF, and MF modes.  
< How to Set >  
Set the focus preset switch  
to ON or  
Ptter tton  
has the  
Press the focus preset  
button.  
.
distant to preset.  
OOThe focused distance will be  
preset.  
OOIf the focus preset switch was  
set to  
, the beeper will  
sound once.  
ENG-8  
Focus Preset  
< How to Focus at the Preset Distance >  
OOWhen turning the playback ring, keep your finger  
away from the shutter button. In One-Shot AF  
mode, the exposure will be locked when you  
press the shutter button halfway and focus is  
achieved. Sif you press the shutter button  
halfway wturning the playback ring, the  
expre mnot be correct.  
OOWhen g the focus preset, set the switch  
OFF.  
focus prefunction will not work while a  
View imagdisplayed on the camera.*  
By turning the playback ring to the left or right,  
the focus shifts as far as the preset dista
Focus will shift freely released of AF fo
while the playback ring is still turned.  
* Nplicable to the EOS-1D X or EOS 5D Mark III  
In tfollowing cases, the focusing distance scale  
(p. 14) will move slightly. It will not affect the image.  
• When you press the focus preset button.  
• When you turn the playback ring.  
OOIf the focus preset switch waet to  
, the
will sound twice.  
Setting the focus mode switco poweocus  
(PF) when using the lens with thO1D X  
or EOS 5D Mark III enables focus change at a  
slow set speed during movie shooting. Also, you  
can make a 2-step change in focus shift speed  
depending on the angle that the playback ring is  
rotated to.  
ENG-9  
6. Power Focus (PF) Mode  
Using the playback ring enables smooth focus change.  
This is a useful feature for changing focus when shooting movies.  
With the focus preset switch set to Ofocmode  
switch to PF.  
Rotate the playback ring to  
change the focus.  
When the playback ring is rted in a certon, focus changes in the same direction as when  
the focusing ring is rotated.  
You can make a 2-step changin focus hift speed depending on the angle that the playback ring is  
rotated to.  
ENG-10  
7. Image Stabilizer  
You can use the image stabilizer in AF, PF, or MF mode.  
Set the STABILIZER switch  
to ON.  
Select the stabde.  
First press the shutter  
button down halfway, then  
press down all the way to  
take the picture.  
OO cts vtions in  
maineffective  
foubjects.  
OOMOcts vertical  
camere during  
owing shots in a horizontal  
ection, and corrects  
horizontal camera shake  
during following shots in a  
vertical direction.  
OO MODE 3: Corrects vibration only  
during exposure. During panning  
shots, corrects vibration during  
exposure only in one direction  
the same as MODE 2.  
OOIf you are not going to use the  
image stabilizer function, s
the switch to OFF.  
OOMODE 1, 2: Press the  
shutter button down halfway  
to stabilize the image in  
the viewfinder and enable  
stabilization.  
OOMODE 3: Press the shutter  
down halfway to initiate  
computation of stabilization,  
then press down all the way  
to enable stabilization.  
ENG-11  
8. Tips on Using the Image Stabilizer  
The image stabilizer for this lens is effective for hand-held shots in the following conditions.  
O MODE 1  
O MODE 2  
ON  
ON  
OFF  
OFF  
OOIn semi-darkened areas sh as indors or  
outdoors at night.  
OOWhen panning subjects in motion.  
OOIn locations where flash photois  
prohibited, such as art museums and theater  
stages.  
OOIn situations where your footing is uncertain.  
OOIn situations where fast shutter settings  
cannot be used.  
O MODE 3  
OOSince camera shake is stabilized only during  
exposure, following a subject is easier such as  
when shooting a fast and irregularly moving  
player during sports photography.  
ENG-12  
Tips on Using the Image Stabilizer  
HS/RS, 3, ELAN 7E/ELAN 7/30/33, ELAN 7NE/  
ELAN 7N/30V/33V, ELAN II/ELAN IIE/50/50E,  
REBEL X/REBEL XS/500, REBEL G/500N, REBEL  
2000/300, REBEL Ti/300V, REBEL T2/300X, REBEL  
K2/3000V, IX, IX Lite/IX7, 3000/88, 5000/888  
OO With the E-1V/HS, 3, ELAN 7E/ELAN 7/30/33,  
ELAN 7NEAN 7N/30V/33V, ELAN II/ELAN II  
E/5E, REL 2000/300, IX, IX Lite/IX7, and  
D30, thStabilizer will not work during self-  
er opera
OO The Image Stabilizer cannot compensate for a  
blurred shot caused by a subject that moved.  
OO Set the STABILIZER switch to OFF when you  
are taking pictures using the Bulb setting (long  
exposures). If the STABILIZER switch is set to ON,  
the image stabilizer function may introduce errors.  
OO The Image Stabilizer might not be fully effective in  
the following cases:  
You shoot from a violently moving vehicle.  
You move the camera dramatically for a panning  
shot in Mode 1.  
OO The Image Stabilizer consumes more power than  
normal shooting, so fewer shots can be taken
use the function.  
OO The image stabilizer operates for about tw
even when your finger is off the shutter bu
Do not remove the lens while lizer
operation. This will cause a lfunction.  
OO With Extender EF2× II attacd to the lens, the  
Image Stabilizer will work wihe following cameras:  
EOS-1D X, EOS-1Ds Mark IIOS-1Ds rk II,  
EOS-1Ds, EOS-1D Mark IV, EOD MaII,  
EOS-1D Mark II N, EOS-1D Mark -1D,  
EOS 5D Mark III, 5D Mark II, 5D, 7D, 60D, 50D,  
40D, 30D, 20D, 20Da, 10D, REBEL T3i/600D,  
REBEL T2i/550D, REBEL T1i/500D, DIGITAL REBEL  
XSi/450D, REBEL T3/1100D, DIGITAL REBEL  
XS/1000D, DIGITAL REBEL XTi/400D DIGITAL,  
DIGITAL REBEL XT/350D DIGITAL, DIGITAL  
REBEL/300D DIGITAL, D60, D30, EOS DCS1,  
DCS3, D2000, D6000, EOS-1V/HS, EOS-1N/DP/  
g a tripod alstabilizes the image.  
owever, depending on the kind of tripod and  
hooting conditions, sometimes it may be better to  
n off the Image Stabilizer function.  
OO Te stabilizer is equally effective for hand-held  
photography and photography with a monopod. The  
Image Stabilizer effect may be reduced, however,  
depending on the shooting environment.  
OO The Image Stabilizer also operates when the lens is  
used with extension tube EF12 II or EF25 II or the  
extender EF1.4× III or EF2× III.  
OO Depending on the camera there may be image  
shake, such as after releasing the shutter. However,  
this does not affect shooting.  
OO If you set the camera’s Custom Function to change  
the assigned button to operate the AF, the Image  
Stabilizer will operate when you press the newly  
assigned AF button.  
ENG-13  
9. Infinity Compensation  
Mark  
10. Hood  
Infinity compensation mark  
Distance index  
cial hothat come with all these  
t out unnted light and protect the  
fhe lens frorain, snow, and dust.  
To compensate for shifting of the infinity focus  
point that results from changes in tempe
The infinity position at normal temperat
point at which the vertical line of the dis
scale L mark is aligned with e distance
To ach the hood, loosen the hood lock knob  
by tuing it counterclockwise. Fit the hood onto  
he les’s hood mount, and tighten the lock knob  
o fix it in place. Use the same procedure, in  
reverse, to remove the hood.  
For accurate focusing in MF subjects anfinity  
distance, look through the viewder whiotating  
the focusing ring.  
ENG-14  
11. Fitting the Lens Cap  
Reverse the lens hood, slip  
it over the lens, and tighten  
the lock knob to fix it in  
place.  
Lift the hook
With the lock knob at the  
opening in the cap, close  
the fastener to fix the cap in  
place as shown.  
fastener, and so  
that tlock kns up  
the ca
OOCan also be attached to the  
front of the hood when using  
the lens.  
ENG-15  
12. Case  
Slot  
Lid  
Hinge  
Strap  
Lever  
Keyhole  
Tshows the EF500mm f/4L IS II USM.  
Fold the strap and fit it into the space near  
Put the lens away as follows
the case hinges.  
Reverse the lens hood, slip iver e lens,  
and attach the lens cap.  
Fasten the lens securely with the strap.  
Close the lid, and then push the lever while  
holding the lid from above to lock.  
Position the tripod mount towards you as  
shown and place it in the case.  
Place so that the hood’s lock knob rests in  
the slot near you.  
OODo not sit on top of the lens case.  
OOPlace the lens in the position intended for it.  
ENG-16  
13. Using the Tripod  
Mount  
14. Security Slot  
A tripod or monopod attaches to the tripod  
mount on the lens.  
Adjusting the Tripod Mount  
By loosening the orientation locking knob on the  
tripod mount you can rotate the camera to set  
the image for any vertical or horizontal position.  
ment slis provided for a wire-type  
ock. The t is located under the cover  
foorientation locking knob.  
A w-type security lock can be purchased  
eparely.  
Replacing the Tripod Mount  
Replacement with the included monopod
can be done at a Canon Service Cente
Since the mount requires special fasten
a safety precaution, do not rlace the m
yourself.  
ENG-17  
15. Drop-In Filters  
<Using a Gelatin Filter>  
A 52(WII)-series drop-in gelatin filter holder with  
a glass filter is included with the lens. The drop-  
in filter holder can be used fitted with a gelatin  
filter (sold separately).  
14mm  
14mm  
47mm  
47mm  
<Installing and Removing>  
Lifp the holder’s retaining plate.  
To remove the drop-in filter, ess the
and right lock buttons and pl the filter ho
straight up out of the slot.  
Cut the gelatin filter as shown and mount it in  
the holder.  
Return the retaining plate to its closed  
position.  
To install the drop-in filter, push e filteholder  
straight down into the slot until it cinto place.  
The Drop-In Screw-Type Filter Holder 52(WII) and  
Drop-In Circular Polarizing Filter PL-C52(WII) are  
also available (sold separately).  
OOThe filter holder can be installed facing either  
forwards or backwards.  
Because the lens optics are designed to include a  
glass filter, you must always install the filter holder,  
even if no gelatin filter is fitted.  
ENG-18  
16. Extenders (Sold Separately)  
Lens specifications when using extender EF1.4× II/III or EF2× II/III are as follows.  
EF500mm f/4L IS II USM  
EF600mm f/4L IS II USM  
EF1.4× II/III  
700  
f/5.6 – 45  
3° 30’  
2°  
EF2× II/III  
1000  
f/8 – 64  
2° 30’  
1° 20’  
EF1.4× II/III  
840  
f/5.6 – 45  
3°  
1° 40’  
2° 30’  
0.21  
EF2× II/III  
1200  
f/8 – 64  
2°  
1° 10’  
1° 40’  
0.30  
Focal length (mm)  
Aperture  
Diagonal  
Vertical  
Horizontal  
Angle of view  
3°  
0.21  
Maximum magnification (×)  
OOAttach the extender to the lens, and then e lene camera. To remove it, reverse the order.  
Errors may occur if you attach the extemerrst.  
OOWith Extender EF2× II/III attached to thnual cus is possible. However, with the EOS-1Ds  
Mark III, EOS-1Ds Mark II, s, E, EOS-1D Mark III, EOS-1D Mark II N, EOS-1D Mark  
II, EOS-1D, EOS-1V/HS cmera, autofocucenter focusing point is possible.  
OOWhen shooting with EOS /A2E/5 fitted witthe EF500mm f/4L IS II USM or EF600mm f/4L IS II  
USM, use –0.5 step exposcompension when using extender EF1.4× II, and use –1 step exposure  
when using extender EF2×
OOExtenders cannot be used morane at a time.  
OOAutofocusing is still enabled with extender EF1.4× II/III attached.  
OOWhen an extender is attached, the AF speed will become slower to retain proper control.  
ENG-19  
17. Extension Tubes  
(Sold Separately)  
You can attach extension tube EF12 II or EF25  
II for magnified shots. The shooting distance and  
magnification are shown below.  
EF500mm f/4L IS II USM  
Focusing Distance Range (mm)  
Magnification (×)  
Close distance Long distance Close distance Long distance  
EF12 II  
EF25 II  
3265  
2904  
20570  
9917  
0.18  
0.22  
0.03  
0.06  
EF600mm f/4L IS II USM  
Focusing Distance Range (mm)  
Magnific
Close distance Long distance Ctance
EF12 II  
EF25 II  
4028  
3619  
29191  
13941  
0.1
0.20  
MF mode is recommended for urate fsing.  
ENG-20  
Specifications  
EF500mm f/4L IS II USM  
500mm f/4.0  
12 groups, 16 elements  
f/32  
EF600mm f/4L IS II USM  
600mm f/4.0  
12 groups, 16 elements  
f/32  
Focal Length/Aperture  
Lens Construction  
Minimum Aperture  
Diagonal: 5°  
Vertical: 2° 45’  
Horizontal: 4°  
Diagonal: 4° 10’  
Vertical: 2° 20’  
Horizontal: 3° 30’  
Angle of View  
Min. Focusing Distance  
Max. Magnification  
3.7 m/12.14 ft.  
0.15×  
4.5 m/14.76 ft.  
0.15×  
Approx. 159 × 238
6.26 × 9.37 inch (at 3.7 m
pprox. 163 × 245 mm/  
6.42 .65 inch (at 4.5 m/14.76 ft.)  
Field of View  
Filter  
Any I)-series drop-in filter  
Max. Diameter and Length  
Weight  
Hood  
146 × 385.08 ch  
Appro5 oz  
168 × 448 mm/6.61 × 17.64 inch  
Approx. 3920 g/138.3 oz  
ET-160(WII)  
Lens Cap  
Case  
Lens case 500B  
E-185B  
Lens case 600C  
OO The lens length is measured om thmount surface to the front end of the lens. Add 26.5 mm  
when including the lens cap and st cap.  
OO The size and weight listed are for the lens only, except as indicated.  
OO The Close-up Lenses 250D and 500D cannot be attached.  
OO Aperture settings are specified on the camera.  
OO All data listed is measured according to Canon standards.  
OO Product specifications and appearance are subject to change without notice.  
ENG-21  
CT1-8576-002  
1208SZ  
© CANON INC. 2012  

Audiovox Mobile Video 128 8342 User Manual
Blaupunkt ORLANDO CM127 User Manual
Boss Audio Systems Car Amplifier A4 User Manual
Casio Financial Calculator FC 200V User Manual
Delphi SA10085 User Manual
Gemini Industries Car Stereo System CDMP 2600 User Manual
HP (Hewlett Packard) Hewlett Packard Car Stereo System 3490A User Manual
JBL Grand Touring GTO1514D User Manual
Jensen MPX6411 User Manual
JVC GET0483 001A User Manual