Released: 9-15-05
Cautions and Warnings
•
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
•
•
The owner or operator shall not make any changes to the unit, antenna, or accessories, as this will void operator’s
authority to operate this equipment.
By adhering to these warnings and safety considerations, stated in the manual and by XM7, accidents and/or personal
injury can be avoided.
-3-
TABLE OF CONTENTS
Select By-Song ................................................................................... 20
Select By Artist ................................................................................... 20
Stock Ticker ........................................................................................ 21
Add Stock ........................................................................................... 21
Erase Stock ........................................................................................ 22
Erase All Stock ................................................................................... 22
Erase Some Stock .............................................................................. 23
Info Extras .......................................................................................... 23
Display Screen Mode .......................................................................... 24
Scrolling Display ................................................................................. 25
Background Mode................................................................................ 25
Set Clock ............................................................................................ 26
Time Zone ........................................................................................... 26
12 / 24 ................................................................................................. 27
Savings Selection ............................................................................... 27
Auto-On ............................................................................................... 28
Auto-Off / Sleep Timer ....................................................................... 28
Set Factory Defaults .......................................................................... 29
Exit Menu ............................................................................................ 30
Search Button ..................................................................................... 30
Memory ............................................................................................... 31
Pre./Dir ................................................................................................ 32
Turning The Xpress Unit OFF ............................................................. 33
REMOTE CONTROL ........................................................................... 34
Remote Control Features ................................................................... 34
CARE AND CLEANING...................................................................... 37
TROUBLESHOOTING ......................................................................... 37
SPECIFICATIONS .............................................................................. 38
WARRANTY ....................................................................................... 39
Congratulations ................................................................................... 2
Cautions and Warnings ....................................................................... 3
TABLE OF CONTENTS ....................................................................... 4
TABLE OF FIGURES .......................................................................... 5
Xpress SYSTEM COMPONENTS ........................................................ 6
INTRODUCTION ................................................................................ 7
OPTIONAL ACCESSORIES ............................................................... 7
GETTING STARTED ............................................................................ 8
XM Activation ...................................................................................... 8
Controls............................................................................................... 10
Receiver Control Features ................................................................. 10
BASIC OPERATION ............................................................................ 12
Turning Xpress ON and OFF ............................................................... 12
Menu Options ...................................................................................... 13
FM Frequency..................................................................................... 14
FM ON or OFF Feature ...................................................................... 14
Brightness + Contrast ......................................................................... 15
Audio Level ......................................................................................... 15
Antenna Aiming (Home Installation) ................................................... 16
Direct Tune.......................................................................................... 17
Search Mode ....................................................................................... 17
Channel Skip/Add................................................................................ 18
Memory Recall .................................................................................... 18
Tune Select ......................................................................................... 19
Tune Select Erase All .......................................................................... 19
Tune Select Erase Some .................................................................... 19
-4-
TABLE OF FIGURES
Figure 1. Your Receiver 8-Character Alphanumeric ID ...................... 8
Figure 2. Xpress Receiver Unit ........................................................... 9
Figure 3. Xpress Receiver Unit Display Screen ................................. 11
Figure 4. XM and Audiovox Logos Power ON Screen ........................ 12
Figure 5. Active Channel Screen........................................................ 12
Figure 6. Main Menu Screen ............................................................... 13
Figure 7. FM OFF Screen ................................................................... 14
Figure 8. FM Frequency Screen ......................................................... 14
Figure 9. Brightness and Contrast Screen ......................................... 15
Figure 10. Audio Level Screen ........................................................... 16
Figure 11. Antenna Aiming Screen ...................................................... 16
Figure 12. Direct Tuning Screen ......................................................... 17
Figure 13. Search Mode Screen ......................................................... 17
Figure 14. Skip/Add Channel Screen .................................................. 18
Figure 15. Memory Recall Screen ...................................................... 18
Figure 16. Tune Select Screen ........................................................... 19
Figure 17. Tune Select Erase All Screen ............................................ 19
Figure 18. Tune Select Erase Some Screen ....................................... 19
Figure 19. Select bySong ConfirmationScreen .................................. 20
Figure 20. Select by Artist ConfirmationScreen ................................ 20
Figure 21. Stock Ticker Screen .......................................................... 21
Figure 22. Add Stock Screen .............................................................. 21
Figure 23. Erase Stock Screen ........................................................... 22
Figure 24. Erase All Stock Screen ...................................................... 22
Figure 25. Erase Some Stock Screen ................................................ 23
Figure 26. Info Extra Screen .............................................................. 24
Figure 27. Display Screen .................................................................. 24
Figure 28. Scrolling Display Screen ............................................... 25
Figure 29. Background Setting Screen ........................................... 25
Figure 30. Set Clock Screen Setting Time Zone ............................ 26
Figure 31. Time Zone Set Screen ................................................... 26
Figure 32. 12 / 24 Hour Selection Screen ....................................... 27
Figure 33. Daylight Savings Selection Screen ............................... 27
Figure 34. Auto-On Screen ............................................................. 28
Figure 35. Auto-Off / Sleep Timer Screen ...................................... 29
Figure 36. Setting Factory Defaults Screen .................................. 29
Figure 37. Category Search Screen ............................................... 30
Figure 38. Scanning Search Screen ............................................... 30
Figure 39. Memory Selection Screens ............................................ 31
Figure 40. Memory Selection Screens ............................................ 31
Figure 41. Direct Channel Entry Screen......................................... 32
Figure 42. Exit Screen .................................................................... 33
Figure 43. Xpress Receiver Remote Control .................................. 34
-5-
Xpress SYSTEM COMPONENTS
XM7 Receiver Model Xpress
Part Number 136-4040
Remote Control Unit
Part Number 136-4042
3 Vdc Battery for Remote,
(1) CR2032
-6-
OPTIONAL ACCESSORIES
INTRODUCTION
The Audiovox Xpress XM7 unit processes the XM satellite sig-
nals received by the externally mounted antenna (purchased
separately for Home or Boom Box Kits). The Xpress XM7 unit
recognizes and decodes the incoming XM program information
and provides an audio signal to your radio or other audio output
equipment.
o
o
o
o
o
Audiovox Home Kit:
Audiovox Boom Box:
Audiovox 2nd Vehicle Kit:
Part Number XMH-10
Part Number XMB-10
Part Number XMC-10
Audiovox FM Direct Adaptor: Part Number XMFM-1
Audiovox RCA Cables: Part Number SAT RCA
NOTE: When installed in a vehicle, the XM signal can be
received and processed virtually anywhere as long as there
are no obvious satellite signal obstructions such as nearby
tall buildings, high terrain, parking garages or tunnels.
The Xpress XM7 unit is typically installed in an accessible loca-
tion of the vehicle (dash area), consistent with line-of-sight
operation of the remote control, and/or within easy reach of the
driver. For home use, situate the Xpress XM7 unit close to your
stereo receiving equipment.
-7-
GETTING STARTED
To obtain the XM7 identification (ID) number, tune to channel 0
and press the Rotary/Select Knob. The 8-character alphanu-
meric XM7 ID will appear on the screen. Write the alphanumeric
ID below (Figure 1) for future reference.
XMActivation
Activating your XM7 radio service is easy. You have one of
two choices to activate your service: Online or by Phone.
NOTE: No adjustments are allowed in this mode. To exit the
Radio ID screen, tune to any channel by turning the rotary knob
and press.
Online Activation Process
First, please make sure the Xpress XM7 unit is working prop-
erly by tuning to the XM7 Preview channel (#1). If you can hear
XM7 Preview, your equipment is ready. NOTE: The antenna
must be installed on the outside of your vehicle for best perfor-
mance.
Please check your 8-character alphanumeric XM7 ID code care-
fully. There is no “I” (eye), “o” (oh), “S” or “F” used. You may wish
to double-check your ID code on the outside of your tuner box.
Enter the ID code below:
Next, make sure you have a credit card and your XM7 Radio
Hardware ID handy. You can display your ID by tuning your
XM7 Radio to channel ‘0’, one down from XM7 Preview (For
tuning instructions see the Receiver Control Features section of
this guide.)
Figure 1. Your Receiver 8-character alphanumeric ID
-8-
Online Activation Process Once the ID code is obtained, log
instructions to activate your Xpress XM7 unit.
LCD
DISPLAY
SEARCH
BUTTON
DISPLAY
BUTTON
MENU
BUTTON
Call-in Activation Process
ROTARY /
SELECT
KNOB
Call XM7 at 1-800-XM RADIO (1-800-967-2346). One of XM7’s
friendly Customer Care representatives will take the necessary
information and walk you through the activation process. After
the activation form is submitted you should keep your receiver
ON for at least 1 hour. This will complete the activation process.
When the Xpress XM7 unit is activated, you will be able to ac-
cess over 150 digital radio channels.
POWER / IR
EYE BUTTON
MEMORY
BUTTON
PRESET/DIRECT
BUTTON
JUMP
BUTTON
PRESET KEYPAD
(NUMBER) BUTTON
The Audiovox Xpress XM7 unit provides 7 control buttons, 1
Rotary/Select Knob and 10 number keys.
Figure 2. Xpress Receiver Unit
-9-
Controls
Rotary/Select Knob – The Rotary/Select Knob is the primary
control for navigating through the various lists and option menus
available. This knob has a dual purpose. In the default mode,
this knob provides sequential tuning through the available pro-
gram channels. When the knob is turned in a clockwise (CW)
direction the unit tunes up one channel at a time. When the knob
is turned in a counter clockwise (CCW) direction the unit tunes
down one channel at a time. When in the list or menu mode,
turning the knob (CW) and (CCW) scrolls UP and DOWN through
the various menus and lists. The current selection from the list
will be highlighted on the display. When the item is highlighted,
press the Rotary/Select Knob to enter the selection.
Receiver Control Features
Display Button - This button allows the user to choose one of
four (4) different formats to present the Artist, Song Title and
data service information on the LCD screen.
Search Button - This button allows the user to search the
next channel category as well as between preset channels or
perform a continuous search. The continuous search will scan
all available channels in all categories or all channels within a
Preset group stopping at each one for four (4) seconds until the
user presses the search button again to make a selection.
Power Button - This button applies power to and removes
power from the Xpress XM7 unit. This button is also the Xpress
XM7 unit’s receiver eye (IR).
Menu Button - The MENU button is used to access
“Menu Options” which allows the user to make feature func-
tion adjustments for personal preferences. Upon entering the
main menu mode, use the Rotary/Select Knob or the Remote
Control UP and DOWN buttons to highlight the desired function
and then press the Rotary/Select Knob or press the (XM) Se-
lect Button on the Remote Control to enter.
Memory Button (mem.) - This button allows the user to
capture and store the current program data information (Artist
& Song Title). You can store up to 20 Artist/Song Title combina-
tions.
-10-
Jump Button – This button allows the user to jump to the
Previous Channel (i.e., switch between the current and previ-
ous channel.
Signal
Strength
Momentary Preset Indicator
(Stays on for 2-seconds)
Time
Preset/Direct Button (pre./dir.) - Each momentary press of
the PRESET button allows the user to switch between (3) banks
of Channel presets (10 presets each A, B, and C) plus Direct
channel entry. When in any of the three preset banks, momen-
tarily pressing any of the number buttons will recall the stored
channel. In the Direct (Dir) mode, use the number buttons to
directly enter the desired channel number followed by pressing
the Rotary/ Select Knob.
Channel
Name
Channel
Number
Artist
Song
Title
Keypad Buttons 0-9 - These buttons are used to directly enter
a desired channel number. They are also used when entering
and recalling preset channel numbers into memory.
Stock, Sports,
and More Info
Display Screen Features - Shown to the right is an example
of an active Display Screen (see Figure 3). Pressing the DIS-
PLAY button from the Default display switches between the
artist name/song title screen, artist name/song title with stock
screen, artist name/song title with sports screen, or large letter
format. When the letter size changes, the field will scroll. This
feature is useful when viewing the display at a distance.
Figure 3. Xpress Receiver Unit Display Screen
-11-
NOTE:
If this is the first time using the Xpress XM7 unit, the
BASIC OPERATION
screen will alternately display the preview channel screen and
a number of messages, including: “Activate Your XM7 1-800-
XM RADIO”. If not, go to channel 1 using the Rotary/Select
Knob on the Xpress XM7 unit or the CH Up/Down buttons on
the remote control.
With the Xpress XM7 unit properly installed, activated and con-
nected to your home/vehicle audio system or boom box, pro-
ceed as follows:
Turning Xpress ON and OFF
Set up your Audiovox Xpress XM7 unit using the installation
instructions included in this Kit (Home Kit, or Boom Box Kit), or
with the help of a professional installer.
NOTE:
Refer to Antenna Aiming during the installation pro-
cedure.
Figure 4. XM and Audiovox Logo Power ON Screen
Press the Power button to turn the unit ON. When the unit turns
ON the XM7 logo will appear for 3-seconds (curved lines on
either side of the XM7 logo gradually appear) (see Figure 4)
followed by the Audiovox logo. These screens will be followed
by the active channel (see Figure 5), which defaults to the last
tuned channel setting prior to power being turned OFF. When
the unit is shut OFF the XM logo will appear and the curved lines
on either side of the XM7 logo gradually disappear.
Figure 5. Active Channel Screen
-12-
While in the menu screen function, if a button is not pressed
within 12-seconds from the previously selected function, the
unit exits the menu screen function and reverts to the default
screen display.
Menu Options
To enter the Menu Options page, press the MENU Button on
either the remote control or the main unit. The Main Menu list will
appear on the screen (see Figure 6). Using the Rotary/Select
Knob, highlight the option you wish to adjust turning (CW) scrolls
DOWN and (CCW) will scroll UP through the various menus and
lists. The current selection from the list will be highlighted on the
display. When the item is highlighted, press the Rotary/Select
Knob to enter the adjust mode.
NOTE:Upon setting and confirmation of a Menu selection,
pressing the Menu button will exit the Xpress XM7 unit to the
active screen (See Figure 5).
The following options are available:
•
•
•
•
•
•
•
•
Stock Ticker
Info Extras
Display Screen Mode
Set Clock
Auto-On
Auto-Off / Sleep Timer
Set Factory Defaults
-Exit Menu-
•
•
•
•
•
•
•
•
•
FMFrequency
Brightness + Contrast
Audio Level
Antenna Aiming
Direct Tune
Search Mode
Channel Skip/Add
Memory Recall
TuneSelect7
Figure 6. Main Menu Screen
-13-
FM Frequency
The following Frequency Setting adjustments are possible:
NOTE:The Xpress XM7 unit has an internal wireless FM trans-
mitter, which allows you to play the audio through any standard
FM receiver, eliminating the need for hardwire connections. In
certain urban areas of the country where strong FM stations
may overpower the Xpress XM7 unit FM transmitted signal, an
FM direct adapter may be needed to achieve a clean audio
signal (Part Number XMFM-1)
Figure 7. FM OFF Screen
The selected frequency must be an unused frequency or a
frequency used by a low powered FM station in your area. If
not, the strong signal from the FM station may overpower the
Xpress XM7 unit FM transmitted signal which may result in
interference.
FM ON or OFF Feature
With the FM Frequency highlighted, press the Rotary/Select
Knob or the (XM) Select button on the remote control to confirm
the selection (see Figure 8).
This feature allows the user to turn the FM Transmitter ON or
OFF. It is recommended that you turn the FM Transmitter OFF if
you are using the low level audio outputs in your particular
application (optional cable needed SAT-RCA) (see Figure 7).
Upon entering the “FM Frequency” mode the FM transmitter will
be OFF by default. To turn the FM Transmitter ON, turn the
Rotary/Select knob CW/CCW or use the UP and DOWN buttons
on the Remote Control to the highlight the desired frequency
(88.1, 88.3, 88.5,.......107.9).
Figure 8. FM Frequency Screen
-14-
Brightness + Contrast
NOTE: When the Receiver is to be used in battery-operated
accessories, such as the Xpress Boom Box (XMB10),
to maximize battery life, it is suggested that the bright-
ness setting be reduced to a minimal level.
This feature allows the user to adjust the brightness and con-
trast of the unit’s display (see Figure 9). Upon entering either the
brightness or contrast adjustment mode, a horizontal bar graph
is displayed with a minus (-) sign on the left and a plus (+) on the
right. Use the Rotary/Select Knob to highlight the contrast or the
brightness adjustment. Once the desired adjustment is high-
lighted, press the Rotary/Select Knob to enter the adjustment
mode. If there is no activity for 12 seconds, the unit will exit to
active channel screen.
Brightness mode: Turn the Rotary/Select Knob CW or use the
UP arrow on the Remote Control to increase the screen’s bright-
ness. Turn the Rotary/Select Knob CCW or use the DOWN ar-
row on the Remote Control to decrease the screen’s brightness.
Once the desired setting is obtained, press the menu button
twice to return to the active channel screen.
Figure 9. Brightness and Contrast Screen
Audio Level
This feature allows the user to set the audio output signal level
(see Figure 10). Upon entering the audio level mode, a horizon-
tal bar graph is displayed with a minus (-) sign on the left and a
plus (+) on the right. Use the Rotary/Select Knob to adjust the
audio level. When the Rotary/Select Knob is turned CW the
audio level signal is increased. When the Rotary/Select Knob is
turned CCW the audio level signal is decreased. The UP and
DOWN buttons on the Remote Control also provide a similar
function. When the desired setting is achieved, press the Ro-
tary/Select Knob or (XM) Select Button on the Remote Control to
confirm.
Contrast Mode: Turn the Rotary/Select Knob CW or use the UP
arrow on the Remote Control to increase the screen’s contrast.
Turn the Rotary/Select Knob CCW or use the DOWN arrow on
the Remote Control to decrease the screen’s contrast. Once the
desired setting is obtained, press the menu button twice to return
to the active channel screen.
-15-
NOTE: To prevent distortion caused by overdriving the audio
playback device input, it is recommended that you adjust the
audio level signal to mid-range.
Antenna Aiming (Home Installation)
This feature allows the user to aim the antenna to optimize XM7
signal reception (see Figure 11). Upon entering the antenna aim-
ing mode, a horizontal bar graph is displayed with a minus (-)
sign on the left and a plus (+) on the right. The horizontal bar
graphs represent the repeater signal and satellite transmission
signal strength. Position the antenna to optimize either the satel-
lite or terrestrial signal. When the optimal setting is achieved,
press the Menu button on the unit or the Menu on the Remote
Control to exit this screen and to return to the main menu.
Screen displayed when the
FM Frequency is set to OFF
NOTE: When the Antenna Aiming screen is selected, this
screen does not time-out like the other menu screens.
This screen will stay active until the Menu Button is
pressed again.
Satellite Signal
Level
Terrestrial Signal
Level
Screen displayed when a
FM Transmitter is set to
“ON”.
Weak
Strong
Figure 10. Audio Level Screen
Figure 11. Antenna Aiming Screen
-16-
Direct Tune
Search Mode
Turn the Rotary/Select Knob CW or CCW to highlight choice (Di-
This feature allows the user to change the way the search
rect Tune On or Direct Tune Off). When the desired setting is button on the Xpress XM7 unit functions. The Search button can
highlighted, press the Rotary/Select Knob or the (XM) Select be set to search categories, to scan through all presets (A, B, C)
Button on the remote control to confirm (see Figure 12). The
direct tune function when enabled (ON), allows the user to manu-
ally tune to a station using the Rotary/Select Knob or the remote
control UP and DOWN buttons. The unit will automatically switch
to the selected station without pressing the Rotary/Select Knob
or the (XM) Select Button on the remote control. When direct
tune is set to off, this allows the user to manually tune to a station
or all available channels.
Upon entering this mode, two options are displayed “Search by
Category” and “Search by Scanning” (see Figure 13). Use the
Rotary/Select Knob or the UP and DOWN buttons on the Remote
Control to switch between the options. When the desired setting
is highlighted, press the Rotary/Select Knob or the XM Select
button on the Remote Control to make the selection. Once a
using the Rotary/Select Knob or the remote control UP and DOWN selection is made a screen will appear to confirm the selection
buttons. The Rotary/Select Knob or the (XM) Select Button on “Search by Category” or “Search by Scanning Set”.
the remote control must be pressed to confirm the selection.
Figure 13. Search Mode Screen
Figure 12. Direct Tuning Screen
-17-
Memory Recall
Channel Skip/Add
This feature allows the user to capture and store the current
program data information (Artist & Song title) with up to 20 list-
ings (20 Artist/Song Title combinations) (see Figure 15).
Press and release the memory (mem) button to save the informa-
tion of the current broadcast song or program. The Xpress XM7
unit can hold up to 20 entries, after which any new information
that is saved will replace the oldest entry in memory. To recall
saved information, press and hold the memory (mem) button for
3-seconds. The Xpress XM7 unit will provide a continuous view
of the Channels, Songs and artists held in memory. Rotating the
Rotary/Select Knob counterclockwise will access the previous
memory content or clockwise to access the next memory con-
tent. The UP and DOWN buttons on the Remote Control also
provide a similar function. To exit to the activate channel screen
press the menu button twice, press the jump button twice or
wait 12 sec.
The Channel Skip/Add function provides the ability to skip over
certain channels when using the Rotary/Select Knob or the UP
and DOWN buttons on the Remote Control. Upon entering this
mode, a channel list is displayed with the current channel in play
highlighted (see Figure 14). In front of each channel is a plus
sign (+) signifying that the channel is not skipped or a minus sign
(-) signifying the channel is skipped. Rotate the Rotary/Select
Knob to navigate the list and highlight the channel to be adjusted.
Once a channel has been highlighted, pressing the Rotary/Select
Knob changes the plus sign (+) or the minus sign (-) to the
opposite sign and adds/subtracts the channel from the channel
skip list. To exit to the active channel screen press the menu
button twice.
ABC News & Talk
Weather Channel
CNBC
-124
+125
127
+
+129 Bloomgberg New
Figure 14. Skip/Add Channel Screen
Figure 15. Memory Recall Screen
-18-
“Yes or No” (see Figure 17). Press the Rotary/Select Knob or the
(XM) Select Button on the remote control to confirm the selection.
Figure 16. Tune Select Screen
TUNE SELECT
Figure 17. Tune Select Erase All Screen
Tune Select Erase Some
This feature allows the user to store current program information
(Artist and Song title) for future comparison against the incoming
XM7 signal. The Xpress XM7 unit can hold up to 20 entries, after
which any new information saved will replace the oldest entry in
memory.
To delete individual and multiple artists/song titles from the Tune
Select list use the Rotary/Select Knob or the UP and DOWN
buttons on the remote control to choose the Artist name or Song
title (see Figure 18). Press the Rotary/Select Knob or the (XM)
Select Button on the remote to mark the Artist or Song title for
removal from the Tune Select list.
To store a song or artist, press and hold the Rotary/Select Knob or
the (XM) Select Button on the remote control until the unit emits a
confirmation tone. When the exact Artist or Song is detected on
the XM7 broadcast, the user will be notified via a confirmation
tone. An alert will also appear on the screen for approximately 8-
sec identifying that a match was found. Pressing the Rotary/
Select Knob or the (XM) Select Button on the remote control while
this screen is active forces the unit to jump to the station currently
playing desired Artist or Song.
Press menu to delete marked items and exit the mode.
Tune Select Erase All
To delete all songs from the Tune Select list go to menu options
then use the Rotary/Select Knob or the UP and DOWN buttons on
the remote control to choose
Figure 18. Tune Select Erase Some Screen
-19-
Select By-Song
Select By Artist
This feature enables the Xpress XM7 unit to search incoming
XM7 broadcast for stored content by song title. Use the Rotary/
Select Knob or the UP and DOWN buttons on the remote control
and select the “Select by Song”. Press the Rotary/Select Knob
or the (XM) Select Button on the remote to confirm the selection
(see Figure 19).
This feature enables the Xpress XM7 unit to search incoming
XM7 broadcast stored content by artist title. Use the Rotary/
Select Knob or the remote control up down buttons and select
the “Select by Artist”. Press the Rotary/Select Knob or the (XM)
Select Button on the remote to confirm the selection (see Figure
20).
Figure 19. Select by Song Confirmation Screen
Figure 20. Select by Artist Confirmation Screen
-20-
Add Stock
Stock Ticker
Two screens will appear “Please Wait” and “Enter Symbol” (see
Figure 22). When the “Enter Symbol” screen appears use the
Rotary/Select Knob or the remote control up down buttons to
select each letter in the stock symbol. Press the Rotary/Select
Knob or the (XM) Select Button on the remote control to confirm
each letter of the symbol.
NOTE: The Xpress XM7 unit will sometimes complete the entry.
When the entry appears on the screen press the Rotary/Select
Knob or the (XM) Select Button on the remote control to confirm
symbol to exit this mode press the menu button twice.
This feature allows the user to monitor various stocks . The
Xpress XM7 unit can monitor up to 20 stock symbols. Use the
Rotary/Select Knob or the remote control up down buttons to
select “Add Stocks” or “Erase Stocks” (see Figure 21). Press the
Rotary/Select Knob or the (XM) Select Button on the remote
control to confirm your selection.
Figure 21. Stock Ticker Screen
Figure 22. Add Stock Screen
-21-
Erase Stock
Erase All Stock
This feature allows the user to erase Stock Tickers individually
or all together (see Figure 23). Use the Rotary/Select Knob or
the UP or DOWN buttons on the remote control to highlight the
desired action, and press the Rotary/Select Knob or (XM) Se-
lect Button on the remote control to confirm the selection.
Use the Rotary/Select Knob or the remote control UP or DOWN
buttons to select/highlight either “NO” to quit or “Yes” to confirm
the deletion of all stock tickers stored in memory. Press the
Rotary/Select Knob or the (XM) Select Button on the remote
control to confirm the selection.
Figure 23. Erase Stock Screen
Figure 24. Erase All Stock Screen
-22-
Erase Some Stock
Info Extras
This feature allows the user to erase Stock Tickers individually
(see Figure 25). Use the Rotary Select Knob or the Up and
Down buttons on the Remote Control to confirm the deletion.
The stock will be immediately removed. To exit this function,
press the Menu button to revert to previously active screen
(Figure 5). A message will appear on the screen “Stock List
Changes Saved”.
This feature allows the user to display the available Info Extras,
primarily sports information. When “Sports” is selected you can
receive XM7 Satellite Radio broadcasts sports information
such as various team scores etc. (see Figure 26). Use the
Rotary/Select Knob or Up and DOWN buttons on the remote
control and select “Sports”. Press the Rotary/Select Knob or
the (XM) Select button on the remote control to confirm the
selection.
To select the various sports available use the Rotary/Select
Knob or the Up and DOWN buttons on the remote control to
highlight and choose the desired sport. Press the Rotary/Se-
lect Knob or the (XM) Select button on the remote control to
confirm the selection and have the unit display teams if avail-
able for the selected category. To select the teams, use the
Rotary/Select Knob or UP and DOWN buttons on the remote
control to highlight the desired team. Press the Rotary/Select
Knob or the (XM) Select button on the remote control to confirm
the selection. A “+” indicates team is selected, a “-“ means team
is not selected.
Figure 25. Erase Some Stock Screen
-23-
Display Screen Mode
This feature allows the user to personalize the display of the
unit to individual preferences. Upon entering Display Screen
mode (see Figure 27), the user can adjust the way information
is viewed. Use the Rotary/Select Knob or the remote control UP
and DOWN buttons to highlight the setting you wish to adjust
then press the Rotary/Select Knob or the (XM) Select button on
the remote control to confirm the selection.
Figure 27. Display Screen
Figure 26. Info Extra Screen
-24-
Background Mode
Scrolling Display
The Background Setting feature allows the user to change the
color of the characters being displayed to white characters on
black (Negative) or black characters on a white background
(Positive Display). Upon entering Background Setting mode
(see Figure 29), use the Rotary/Select Knob or the remote con-
trol UP and DOWN buttons to highlight either Negative Display or
Positive Display then press the Rotary/Select Knob or the
Remote’s (XM) Select button .Selection acceptance is confirmed
by audio beeps and confirmation screen.
The Scrolling Display feature allows the user to program the
Xpress XM7 unit to scroll stock tickers or Info Extra information
across the bottom portion of the screen (continuous stream of
information). The paging mode feature presents the data one
page at a time and is useful when viewing the display at a
distance. Upon entering Scrolling Display mode (see Figure
28), use the Rotary/Select Knob or the remote control UP and
DOWN buttons to highlight either Scrolling On or Scrolling Off
then press the Rotary/Select Knob or the Remote’s (XM) Select
button. Selection acceptance is confirmed by an audio beep
and confirmation screen.
Figure 28. Scrolling Display Screen
Figure 29. Background Setting Screen
-25-
Set Clock
Time Zone
This feature is used set the clock to the Time Zone in which the
user resides (see Figure 31). Use the Rotary/Select Knob or the
remote control UP and DOWN buttons to highlight the desired time
zone. Press the Rotary/Select Knob or the Remote’s (XM) Select
button to enter your selection. Acceptance is confirmed by an
audio beep and confirmation screen.
This feature allows the user to personalize the clock display.
The clock data is provided via the XM7 signal, and is displayed
according to the users settings. Use the Rotary/Select Knob or
the UP and DOWN buttons on the remote control and highlight one
of the three options on the Set Clock Screen (See figure 30).
Press the Rotary/Select Knob or the Remote’s (XM) Select button
to set your selection. Refer to the following paragraphs for addi-
tional instructions.
Figure 31. Time Zone Set Screen
Figure 30. Set Clock Screen Setting Time Zone
-26-
Savings Selection
12/24 Hour
This feature allows the user to enable or disable Daylight Sav-
ings Time (see Figure 33). Use the Rotary/Select Knob or the
remote control UP and DOWN buttons to highlight either Standard
or Daylight Savings then press the Rotary/Select Knob or the
Remote’s (XM) Select button to enter your selection. Acceptance
is confirmed by an audio beep and confirmation screen.
This feature is used to set the time displayed to either a 12-hour
(Default) or 24-hour format (see Figure 32). Use the Rotary/
Select Knob or the remote control UP and DOWN buttons to
highlight either “12 hour Clock” or “24 Hour Clock” then press the
Rotary/Select Knob or the Remote’s (XM) Select button to enter
your selection. Acceptance is confirmed by an audio beep and
confirmation screen.
Figure 33. Daylight Savings Selection Screen
Figure 32. 12 / 24 Hour Selection Screen
-27-
Auto-Off / Sleep Timer
Auto-On
This feature allows the user to program the Xpress XM7 unit to
automatically shut OFF if the unit remains in an inactive state for
a period of time ranging between 15 Minutes and 3 hours (see
Figure 35). There are 6 available settings:
The Xpress XM7 unit is configured to shut down when the
vehicle is shut OFF or power is disconnected. By default, when
the power to the unit is reapplied the user must press the
Power button to turn the unit back ON. This feature allows the
user to program the Xpress XM7 unit to automatically turn ON
when the power to the unit is reapplied (much like a car radio).
When in the Auto-On menu use the Rotary/Select Knob or the
Remote control UP and DOWN buttons to highlight either On or
Off (see Figure 34). When the desired setting is highlighted,
press the Rotary/Select Knob, or the remote’s (XM) select button
to enter your selection. Acceptance is confirmed by an audio
beep and confirmation screen.
•
•
•
•
•
•
15 Minutes
30 Minutes
45 Minutes
1 Hour
2 Hours
3 Hours
This feature is useful in preventing the vehicle battery from
draining in cases where the unit is installed with a constant
power source. It is also useful as a Sleep Timer turning the unit
OFF automatically after a period of time.
When in the Auto-Off / Sleep Timer mode use the Rotary/Select
Knob or the Remote Control UP and DOWN buttons to highlight
one of the six (6) time settings you wish to select.
When the desired time setting is highlighted, press the Rotary/
Select Knob, or the remote’s (XM) select button to enter your
selection. Acceptance is confirmed by an audio beep and confir-
mation screen.
Figure 34. Auto-On Screen
-28-
If yes is selected all of the users preset settings are erased and
the unit returns to the original factory default settings.
A second and third screen will appear to confirm the selection
(see Figure 36).
NOTE: Once Yes is selected the change cannot be undone
and all user personal settings will be lost.
Figure 35. Auto-Off / Sleep Timer Screen
NO
Set Factory Defaults
YES
This feature allows the user to reset the Xpress XM7 unit back
to the original factory settings. Upon entering the Factory De-
fault mode, use the Rotary/Select Knob or the UP and DOWN
buttons on the remote control to switch between the No or Yes
function.
Figure 36. Setting Factory Defaults Screen
-29-
the Search button, Rotary/Select Knob or the (XM) Select but-
ton on the remote control is pressed to confirm the selection.
Exit Menu-
To exit the menu options rotate the Rotary/Select Knob CW or
press the down arrow on the remote control to highlight ‘Exit
Menu’. Press the Rotary/Select Knob or the (XM) Select button
on the remote control to confirm the selection.
Search Button
The Search button provides the ability to search by category or
to scan directly through each of the available channels or
through each of the presets (A, B, C) depending how the but-
ton is setup (see Search Mode section for setup instructions).
When the Xpress XM7 unit is set to “Search by Category”, each
press of the Search button will advance through all available
categories. When a desired category is reached rotate the
Rotary/Select Knob to select the desired setting and press the
Rotary/Select Knob or the (XM) Select button on the remote
control to enter the selection.
Figure 37. Category Search Screen
When the unit is set to “Search by Scanning”, it will continu-
ously search through the presets (A, B, C) or all the available
channels (in five (5) second intervals) in the direct mode until
Figure 38. Scanning Search Screen
-30-
To recall the saved information, press and hold the memory
(mem.) button for three (3) seconds and the MEMORY RECALL
screen will be displayed (see Figure 40). If there is more than
one (1) entry in memory, use the Rotary/Select Knob or the
remote control UP and DOWN buttons to scroll through all stored
entries.
To exit this mode, either press the Menu button twice or Jump
button once. This mode will also time-out after 10-seconds and
return to the active screen.
Memory
This feature allows the user to program into memory favorite
song titles, artist names and channel information. To make an
entry, press the memory (mem.) button and a “Saved in Memory”
confirmation screen will appear (see Figure 39). Up to 20
entries can be stored. When 20 entries have been stored any
new information that is saved will replace the oldest entry in
memory.
Figure 40. Memory Selection Screens
Figure 39. Memory Selection Screens
-31-
Pre./Dir
The Pre./Dir button determines whether the numbered buttons 0
through 9 will operate as a keypad for entering station numbers
directly, or as presets (A, B, C) used to select stations. The unit
informs the operator by displaying the selected mode (DIRECT,
PRESET A, PRESET B, PRESET C) on the top line of the display.
Numbered Buttons 0-9
Figure 41. Direct Channel Entry Screen
Preset (A, B, C)
The numbered buttons (0 through 9) provide the operator
with a means of selecting stations by entering the station
number when the unit is set to DIRECT, or selecting preas-
signed stations when the unit is set to operate in PRESET (A,
B, C).
The unit has the capability of storing three sets of 10
preassigned stations for a total of 30 preassigned stations.
To assign a station to a number button, tune in the desired
station and hold down the desired number button until the
unit signals acceptance by issuing one short beep and
displaying a screen to confirm for about 1 second.
Direct
When the unit is set to operate in this mode, station selection
can be accomplished by entering its number directly. (e.g., to
select station #23, press 23.) The unit will display the fol-
lowing screen and change to the desired station 2 seconds
later.
-32-
Turning The Xpress Unit OFF
To turn the Xpress XM7 unit OFF, press the power button on the
unit or on the remote control. The following screen will appear,
the curved lines on either side of the XM7 logo gradually disap-
pear and the unit will shut down.
Figure 42. Exit Screen
-33-
REMOTE CONTROL
Remote Control Features
The wireless remote control supplied with the Xpress XM7 unit
is capable of operating most of the features from a remote
location. Each button on the remote control functions in the
same way as the button on the Xpress XM7 unit. For a full
description of a keypad button and function refer to the preced-
ing sections in this manual. For optimal operation of the remote
control, always aim it toward the Remote Sensor on the front
panel of the main unit.
(+) Button
(-) Button
Figure 43. Xpress Receiver Remote Control
-34-
Menu Button (menu) – The MENU button is used to access
“Main Menu” options which allows the user to make feature
function adjustments and set personal preferences. Upon en-
tering the main menu mode, use the UP and DOWN buttons to
highlight the desired function. Press the (XM) SELECT button to
confirm the selection.
Memory Button (mem) – This button allows the user to cap-
ture and store the current program data information (Artist &
Song Title). You can store up to 20 artist/song title combinations.
Display Button (disp) – This button allows the user to choose
one of four (4) different formats presenting the Artist, Song Title
and data service information on the LCD screen. Pressing the
Display button while viewing the active display switches be-
tween the artist name/song title screen, large letter format, or
artist name/song title with data service ticker (sports, stock op-
tions, etc.) screen. When the letter size changes, the field will
scroll. This feature is useful when viewing the display at a dis-
tance.
Select Button (XM) – This button is used to confirm a desired
channel/category selection and various menu options. This but-
ton is also used to program the ARTIST/SONG into the Tune
Select feature by pressing and holding for two (2) seconds (see
TuneSelect7).
Mute Button (mute) – This button is used to mute and un-mute
Preset/Direct Button (pre/dir) – Each momentary press of
the PRESET button allows the user to switch between 3 banks
of Channel presets (10 presets each A, B, and C, plus Direct
(Dir) channel entry. When in any of the three preset banks,
momentarily pressing any of the number buttons will recall the
stored channel. In the Direct (Dir) mode, use the number
buttons to directly enter the desired channel number.
the selected audio.
Jump Button (jump) – This button allows the user to jump from
the current channel to a previous channel (i.e., switch between
current and previous channel).
Number Buttons (0-9) – These buttons are used to select
preset numbers and to directly enter a channel number.
-35-
Search Button (search) – Depressing the Search button will
cause the unit to initiate a search based on the search mode
stored in the unit.
Channel Up Button – This button is used to scroll through
upper channels in the channel list as well as navigate to the next
higher line in a list of menu options.
Channel Down Button – This button is used to scroll through
lower channels in the channel list as well as navigate to the next
lower line in a list of menu options.
(+) Button – This button is used to tune to the next higher chan-
nel number.
(-) Button – This button is used to tune to the next lower channel
number.
Power Button – This button is used to turn the power to the unit
ON and OFF
IR Transmitter – The IR Transmitter sends the wireless com-
mands to the main unit. It must be pointed in the direction of the
main unit in an unblocked path to function correctly.
-36-
CARE AND CLEANING
TROUBLESHOOTING
• Keep the unit away from excessive moisture or where
it may get wet.
• It is strongly recommended that the unit be installed and
kept away from heat sources or direct sunlight.
• When cleaning, use only a soft, dry cloth.
• Never use any chemicals, abrasives, solvents, alcohol
based cleaning solutions or ammonia.
• Always operate the unit where air can circulate com-
pletely around the unit.
-37-
SPECIFICATIONS
Audio Output
3.5mm Diameter Min-Stereo Jack
3.5mm Diameter Min-Stereo Jack
AUX (Audio) Input
Power Supply:
5 Volt, 2 Amp Maximum, Negative Ground, DC Input. CAUTION:
Use only the Audiovox approved adapter specified in the kit for
the Xpress XM7 Satellite Radio Receiver, or the unit could be
severely damaged.
Antenna
1 RF SMB Connector
Dimensions
H X W X D
2.44 Inches X 4.44 Inches X 1.22 Inches
(62.0mm) X (112.7mm) X (31.0mm)
-38-
12 MONTH LIMITED WARRANTY
AUDIOVOX ELECTRONICS CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part
thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such
defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale),
specification of defect(s), transportation prepaid, to an approved warranty station or the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to costs incurred for installation, removal or reinstallation of
the product, damage to speakers, accessories, or vehicle and home electrical systems, malfunction of satellite transmissions, repeater signal or receiver
unit.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration,
improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT
OFTHECOMPANY'SLIABILITYUNDERTHISWARRANTYISLIMITEDTOTHEREPAIRORREPLACEMENTPROVIDEDABOVEAND,INNOEVENT,SHALL
THECOMPANY'SLIABILITYEXCEEDTHEPURCHASEPRICEPAIDBYPURCHASERFORTHEPRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY,SHALLBELIMITEDTOTHEDURATIONOFTHISWRITTENWARRANTY.ANYACTIONFORBREACHOFANYWARRANTY
HEREUNDERINCLUDINGANYIMPLIEDWARRANTYOFMERCHANTABILITY MUSTBE BROUGHT WITHIN A PERIODOF48MONTHS FROM DATE
OFORIGINALPURCHASE. INNOCASESHALLTHECOMPANYBELIABLEFORANYCONSEQUENTIALORINCIDENTALDAMAGESFORBREACH
OFTHISORANYOTHERWARRANTY,EXPRESSORIMPLIED,WHATSOEVER. NopersonorrepresentativeisauthorizedtoassumefortheCompany
any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the
U.S.A. : AUDIOVOX ELECTRONICS CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 (1-800-645-4994)
128-7351
-39-
-40-
-41-
© 2005 Audiovox Electronics Corporation
128-7454
|