MMSV58
5.8" LCD SUN VISOR MONITOR
WITH MIRROR AND DOME LIGHT
Installation Guide
MATERIALS INCLUDED IN THIS PACKAGE:
1)
2)
3)
4)
MMSV58 Sun Visor Video Monitor (P/N 136-3781) (1 pc)
Monitor Mounting Shroud (P/N 1024053) (1pc)
Remote Control (P/N 136-B3696) (1pc)
Hardware Package:-
•
•
M2.5 x # 8” Screws (4 pcs)
Rubber Screw Plug Caps ((138-1324) (4 pcs)
7 Pin Power Wire Harness (P/N1123455) (1 pc)
5)
ꢀ
ꢁ
ꢂ ꢃ
ꢄ
GROUND ACTIVATED
TOOLS REQUIRED:
Rotary Tool
Phillips Screwdriver
Utility or Razor Knife or Shears
Wire Strippers
Upholstery hook tool (for removal of panels as necessary)
Electrical Tape
Masking Tape
Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe)
Fine Point Marker – to mark visor
Misc. electrical connectors (to connect to vehicle power source). Requirements will vary from vehicle to
vehicle.
2
INSTALLATION NOTES
•
NOTE: System component installation options vary, see the individual owner’s
manuals for each component in your system to obtain a full understanding of each
component’s operation.
•
NOTE: Each vehicle is different. Your specific disassembly and reassembly may
vary slightly from the installation guide shown.
INSTALLING THE MMSV58
1. Remove the Sun Visor from the vehicle.
With Illuminated Vanity Mirror
•
•
•
Remove visor attaching hardware (screw) and set aside for re-assembly.
Pull visor downward and disconnect any power connections.
Once the visor is removed, place it on clean flat work surface
Figure 1. Sun Visor With Vanity Mirror
Without Illuminated Vanity Mirror
•
•
Remove visor attaching hardware (screw) and save for re-assembly.
Once the visor is removed, place it on clean flat work surface
Figure 2. Sun Visor Without Vanity Mirror
3
2. Remove all accessories from the visor such as mirror/door/light assemblies, etc (if
applicable) and set aside for re-assembly.
Figure 3. Sun Visor With All Accessories Removed
3. Once all accessories are removed, check the dimensions and material depth of the sun
visor to estimate the fit for your application.
NOTE: If the visor had no accessories to remove and does not have a open cavity,
measure the thickness of the visor material between the rigid material in the center and
the surface.
Figure 4. Sun Visor With All Accessories Removed
4. Using the rear of the visor-mounting shroud as a template, mark the visor.
Shroud used as
template
Figure 5. Marking The Visor Material
4
5. Using a Razor Knife cut an “X” through the material.
Figure 5. Cutting The Visor Material
6. Peel back the 4 flaps. Carefully cut out the plastic of the visor using a rotary tool. Be sure
that the tool does not grab the fabric/leather or damage may occur to the material. Lay
the 4 flaps back into the visor cavity.
7. Push the power/signal harness connector thru the back of the shroud and press the
shroud in the visor cavity. NOTE: The cavity may require some grinding using a rotary
tool to properly seat the shroud into the cavity. If grinding is needed be sure not to
damage the visor material.
Figure 6. Power/Signal Harness And Shroud Installed
8. Adhere the visor mounting shroud. (Example: silicone, two part quick drying epoxy, hot
glue, screws if a double wall is present, double side tape, etc) Place the shroud back into
the cavity and apply a good amount of pressure to the base if glue tape or epoxy is used
sets. Make sure you have pulled the monitor connector through the access hole on the
lower right hand side of the shroud. NOTE: When using glue or double side tape, make
sure to use only high temperature rated products that can handle the extreme
temperatures of the vehicles interior
9. Plug the power power/signal harness into the rear of the MMSV58.
5
Figure 7. Installing The Monitor Shroud
10. Snap the screen into the visor mounting shroud Screw the screen to the visor mounting
shroud using the 4 screws (supplied).
11. Install the 4 screw caps (supplied) in the holes on the 4 corners of the assembly.
Figure 8. Installing The Monitor
12. Reinstall the sun visor in its original position using the attaching hardware removed in
step 1. of this installation procedure.
13. Route the power/signal harness from the sun visor down the A-Pillar and behind the
dashboard for connections to the video equipment and/or backup camera.
6
WIRING
GROUND ACTIVATED
Figure 9. Power/Signal Harness
Emergency
Brake Switch
MMSV58
Power Source
Vehicle Ground
Video Source
VCP (VIDEO 1)
DVD (VIDEO 2)
Figure 10. Typical System Installation
7
TROUBLESHOOTING
Symptom:
Remedy:
No power at Video Monitor
-Verify +12 VDC on Red wire at 7 pin Harness behind video
monitor. Verify ground connection with continuity test from
known good ground to black wire at 7 pin Harness
-Verify that the correct source is selected (i.e.: 1,2,3 or 4).
Verify that the source is on and playing a known good media
(such as a videotape). Verify connections at both ends of the
source component harness. Verify that the Gray wire is
connected to the Emergency Brake wire.
Power but no video or sound
No Infrared Remote Functions
-Check batteries in the hand held remote.
8
© Copyright 2004 AEC 150 Marcus Blvd. Hauppauge, NY 11788
128-7158
|