• This is a small and slim eneloop charger for AA and AAA
1. Insert one or two eneloop batteries into the charger. Raise or lower
the adjuster depending on the type of battery to be charged.
• Raise the adjuster to charge AA batteries.
eneloop batteries.
• This charger is only for AA and AAA Ni-MH
batteries made by SANYO.
• Do not attempt to charge alkaline batteries.
• Do not connect equipment to other USB ports while
charging. The available power required may be
exceeded and the computer may be damaged or data
may be lost.
• One or two AA or AAA eneloop batteries can be charged.
• No AC adapter is required.
• Lower the adjuster to charge AAA batteries.
Operating Instructions
• AA and AAA batteries cannot be charged at the same time.
Note: Insert the batteries matching the polarity of the charger.
2. Insert the USB connector of the charger into the USB port of an
operating computer. Charging takes place when the LED charge
Indicator is flashing.
Thank you for purchasing this SANYO product. For safe
and correct use, please read these instructions carefully.
Please keep the instructions for later reference.
• Do not connect via a USB connection cable. This may
cause interference with other electrical equipment.
• Do not use the charger in areas of high humidity or
where it may be exposed to water.
• Insert the batteries into the charger with matched
polarity.
Adjuster (+) c
Lower for AA
Specifications
Note: Do not connect other equipment to other USB ports on the
computer while charging or the required Power may be exceeded.
Charging might be stopped or the computer damaged or Data lost.
The power supply capacity may be exceeded and charging may
become impossible or the computer may be damaged and important
data may be lost.
Input
connector
DC 5 V, max. 500 mA
Output
DC 1.2 V, 850 mA x 1 (Quick), 450 mA x 2
housing
(-) contact for
Battery charge times
(approx. minutes)*
eneloop Ni-MH AA (typ. 2000 mAh)
1 pc. 140 min, 2 pcs. 280 min
• Disconnect the charger from the port after
completion of charging.
3. When charging has been completed the LED Charge indicator
remains lit. Remove the USB connector from the USB port of the
computer and remove the battery (batteries).
• Lower the adjuster when the charger is not being
used. Put the USB connector into USB housing of the
charger.
eneloop Ni-MH AAA (typ. 800 mAh)
1 pc. 60 min, 2 pcs. 120 min
(*) Guideline value only; actual charging times may vary slightly. Please refer
to Operating Instructions.
Note: If the adjuster has been raised, lower the adjuster for storage.
• Do not pull the USB connector and the cord
excessively.
The following can be considered when the charge time is exceeded:
Dimensions (L x W x H)
Weight
93 x 47 x 17.5 mm
Approx. 47 g
• Do not touch the charger or the batteries with wet
Depending one or
two AA or
• Use the charger in the temperature range from 0 °C
Charging temperature
range
Raise the ad
• Do not insert Metallic objects other than eneloop
batteries into the charger.
Connector type
USB type A
Models with a USB port as standard equipment
where the computer manufacturer guarantees
the operation of the USB port and has a USB
port fitted as Standard equipment.
Compatible computer
• Do not modify or disassemble the charger.
• In case of abnormalities or trouble, disconnect the
USB connector from the computer port and contact
your dealer.
• Keep the charger out of reach of small children. If
children are to use the charger, keep them under
• Do not store the charger in locations with high
humidity or dust.
LED Charge indication light
– – – – – – – – Approx. every 1.5 sec
Charging
Temperature range
Discharging (battery use)
Charging
–––––––––––
Steady
Charging completed (*)
Battery abnormal
-5 °C – 50 °C
0 °C – 40 °C
-20 °C – 30 °C
- - - - - - - - - - - Approx. every 0.5 sec
Not lit
Stop during charging (computer
standby mode etc.)
Storage
Usage outside of these temperature ranges may decrease the performance
and/or the life of the battery.
(*) When two batteries are being charged, the condition where charging of both
batteries has been completed.
|