USER'S MANUAL
AW07P2 Series
AW09P2 Series
AW12P2 Series
Window-type Room Air Conditioner (Cooling)
E
DB98-ꢀ7ꢀ04A
DB98-27204A.indd
15
2007-1-23
9:18:46
Contents
PREPARING YOUR AIR CONDITIONER
n
Safety Precautions ........................................................................................
ꢀ
4
n
Air Conditioning Unit-Main Parts and Control Panel.....................................
OPERATION YOUR AIR CONDITIONER
n
Cooling Your Room.......................................................................................
5
n
n
n
n
n
Airing Your Room..........................................................................................
Switching the Air Conditioner Off..................................................................
Setting the Off Timer.....................................................................................
Adjusting the Air Flow Direction Horizontally ................................................
Adjusting the Air Flow Direction Vertically ....................................................
6
6
7
7
8
RECOMMENDATIONS FOR USE
n
Temperature and Humidity Ranges ..............................................................
8
9
n
n
Cleaning Your Air Conditioner.......................................................................
Solving Common Problems........................................................................... ꢁ0
INSTALLATION............................................................................................. ꢁꢁ
The illustrations in the step-by-step procedures use four different symbols:
PRESS
PUSH
IMPORTANT
NOTE
CAUTION
“The high inrush current of the starting compressor motor can have adverse effects to
the operation of other equipment under unfavorable mains conditions. This equipment
does not comply with the relevant technical standards for the limitation of voltage
fluctuations and flicker.”
Before connection this equipment to the power supply system, please report to your
suply authority and obtain the consent.
Do not connect other electric appliances to the same supply lines.
E-3
DB98-27204A.indd
3
2007-1-23
9:18:37
Air Conditioning Unit - Main Parts and Control Panel
The design and shape are subject to
change according to the model.
Air Outlet
Inner air flow blades
(right/left orientation)
Air inlet (Inside)
Outer air flow blades
(up/down orientation)
The air filter is
located in side
Air inlet (Outside)
Ventilation lever
Power Cable
The type of the power plug
may differ according to the
type of local power supply.
Power plug
Operating mode
selection dial
Temperature
control dial
Air flow blade
swing switch
Fan speed switch
E-4
DB98-27204A.indd
4
2007-1-23
9:18:37
Cooling Your Room
You must select the Cool mode if you wish to lower the temperature
in your room.You can also set the fan speed.
ꢁ
To switch the unit on,simply turn the Timer dial to "Continue" position.
The air conditioner starts operating.
Result:
ꢀ
To adjust the temperature, turn the temperature control dial
to the desired position.
Possible temperatures: Between ꢁ8 °C and ꢀ9 °C inclusive.
Result:
The air conditioner starts cooling if the room temperature is
higher than the selected temperature.
3
Press the "Fan Speed" mode selector to the High or Low position.
Result:
The Fan speed is adjusted.
E-5
DB98-27204A.indd
5
2007-1-23
9:18:37
Airing Your Room
If the atmosphere in your room is stale, you can air it using the Fan
feature and if necessary, evacuate the stale air outside.
ꢁ
If you wish to evacuate stale air outside, push the ventilation lever on the
front of the unit to the right and the open position ( ).
Result:
Otherwise, push the ventilation lever to the left and the closed position (
Result: The air simply circulates inside the room.
The air inside the room circulates and stale air is evacuated outside.
).
ꢀ
To switch the unit on,simply turn the Timer dial to "Continue" position.
Result:
The air conditioner starts operating.
3
To airing your room only, turn the temperature control dial
to "ꢁ" position.
The air conditioner runs in fan mode.
Result:
Press the "Fan Speed" mode selector to the High or Low position.
The Fan speed is adjusted.
4
Result:
Switching the Air Conditioner Off
You can switch the air conditioner off whenever you want.
To switch the unit off, simply turn the Timer dial to the "off " position.
Result: The air conditioner stops operating.
ꢁ
E-6
DB98-27204A.indd
6
2007-1-23
9:18:38
Setting the Off Timer
The Off Timer enables you to switch off the air conditioner automatically
after a given period of time. You can set the period of time from 0 hour
to12 hours.
You can set the Off Time at any time.
ꢁ
To set the off time, simply turn the Timer dial to the time you want.
Possible time is lower ꢁꢀ hours inclusive.
To cancel the Off Timer function,That is to say,make the unit run
incessantly, you can turn the timer dial to "Continue" position.
Result:
The air conditioner switches off automatically when the
operating time reaches zero
Adjusting the Air Flow Direction Horizontally
Depending on the position of the unit in your room, you can adjust the
orientation of the inner air flow blades on the right-hand side of the unit,
thus increasing the efficiency of the air conditioner.
Set the air flow blade swing switch to the on position.
Result: The inner blades swing automatically left and right.
ꢁ
To stop the blades moving left and right, set the air flow blade swing
switch to the off position.
ꢀ
To stop the blades in a specific position and orient the air flow in
the corresponding direction, simply set the switch to the off
position when the blades are in the desired position.
E-7
DB98-27204A.indd
7
2007-1-23
9:18:39
Adjusting the Air Flow Direction Vertically
Again depending on the position of the unit in your room, you can adjust
the orientation of the outer air flow blades on the right-hand side of the unit.
RECOMMENDATION
When...
Adjust the blades to face...
Cooling
Upwards.
Adjust the air flow blades to the desired position, by pushing them upwards or
downwards.
If you orient the air flow blades downwards and the unit operates in Cool mode
for long periods of time, dew may:
From on the surface of the blades
Drip from the blades
Temperature and Humidity Ranges
The following table indicates the temperature and humidity ranges
within which the air conditioner can be used in the best condition .
Mode
IndoorTemperature
OutdoorTemperature
Indoor Humidity
Cooling
ꢀꢁ°C to 3ꢀ°C approx.
ꢀꢁ°C to 43°C approx.
80% or less
If the air conditioner is used at...
Then...
The automatic protection feature may be triggered and the air
conditioner stopped.
Higher temperatures
A water leakage or some other malfunction may happen if the
heat exchanger freezes.
Lower temperatures
Water way condense on and drip from the surface of the unit if
it is used for long periods.
Higher humidity levels
E-8
DB98-27204A.indd
8
2007-1-23
9:18:39
Cleaning Your Air Conditioner
Be sure to clean the air filter periodically to maintain the air conditioner in
the best condition for a long period of time.
When cleaning the air conditioner, turn it off and pull out
the power plug.
IMPORTANT
ꢁ
Hold the front grille handle, slightly pull it to the left side and open the front grille.
The removal of the front grille makes it easier to clean the air
conditioner. Open the grille as much as possible.
CAUTION
Removal and Reassembly of the Front Grille
ꢁ
Grasp the lower part of the front
grille and the front grille handle,
then open the grille. (The open
angle of front grille has not to be
exceeded ꢀ5 degree)
ꢀ
3
Lift the front grille slightly and
remove it from the front panel.
Reassembling of front grille
should be done in reverse
order of disassembly.
ꢀ
3
4
5
Pull the air filter to the right side.
Remove all dust on the air filter with a vacuum cleaner or brush.
When you have finished, insert the air filter back into its original position.
Wipe the surface of the unit with a neutral detergent and then wipe it again
with dry cloth.
(Be sure not to use benzene, solvent or other chemical products.)
If you...
Then...
The air conditioner has two or three grille
grooves depending on the model.
Will not be using the
air conditioner for a
long period of time
Set the operating mode selection dial
to “LOW FAN” and let it run of a few
hours to dry the inside of the air
conditioner thoroughly.
Switch the air conditioner off and
unplug it from the wall socket.
Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the operating mode selection dial
to “LOW FAN” and let it run of a few
hours to dry the inside of the air
conditioner thoroughly.
E-9
DB98-27204A.indd
9
2007-1-23
9:18:42
Solving Common Problems
Before contacting the after-sales service,perform the following simple checks.
They may save you the time and expense of an unnecessary service call.
Problem
Explanation/Solution
The air conditioner does not
operate at all
Check that the circuit breaker used for the air conditioner has not
been triggered.
Check that the power cable is plugged into a wall socket and the
socket is switched on, if necessary.
Check that the correct operating mode has been selected
(cooling or airing).
The air conditioner does not cool
Check that the correct operating mode has been selected .
The room temperature may be too low.
Dust may be blocking the air filter; refer to page 8
cleaning instructions.
Check that there is no obstacle blocking the air flow into or out of
the unit.
The air flow direction does not
change when you set the air
flow blade swing switch to the
on position
Check that the air conditioner has been switched on;
if necessary, turn the operating mode selection dial;
refer to page 7.
Odours are permeated in the
room during air conditioning
Air the room.
E-ꢁ0
DB98-27204A.indd
10
2007-1-23
9:18:43
Installation
Before installation, be sure to check the installation area or the air
conditioner, and drain hose.
Checkpoints prior to installation
ꢁ
ꢀ
Check the cabinet and front grille of the unit for any harmful defects
such as scratches.
Be sure to check the power supply.
- Refer to the specifications on the label attached to the unit.
Installation Conditions
ꢁ
As the unit is heavy, the wall or window of the installation area should
have sufficient strength and durability for operation of the air conditioner,
and for prevention of any vibration or noise.
If it is weak, reinforcement work should be performed separately.
ꢀ
It is advisable to install the air conditioner in the north or west side to
prevent the effect of direct sunlight.
When installing it in the south or east side due to unavoidable
circumstances, it is advisable to install the sunshade to prevent the
direct sunlight.
In this case, take care not to cause any hindrance to the flow of outside air.
3
When installing the air conditioner, be sure to obtain sufficient space on
the rear side of the unit for smooth flow of air.
When operating the air conditioner in closed areas such as inner building
with cooling operation, and result in trouble with the unit.
See the illustration below.
Awning
The appliance must be fixed well by screw or similar
method.
75mm
min.
300mm
"A"
Fence, wall
or other
500mm
500mm
500mm
obstacle
Approx.3
MODEL
AW07/AW09
AWꢁꢀ
“A”
ꢁ45
ꢁ70
750mm
150mm min.
If the wall is greater than ꢁ50mm thick,
cut the wall back on a 45° angle if possible.
Outdoor side
Indoor side
45
45
ꢁ00mm or more
E-ꢁꢁ
DB98-27204A.indd
11
2007-1-23
9:18:44
Installation(Cont.)
Installation of the Drain Tube
Fix the drain tube as shown in the figure.
Rear
Rubber cap
Gasket
Drain Tube
Screws(ꢀEA)
E-ꢁꢀ
DB98-27204A.indd
12
2007-1-23
9:18:44
Memo
E-ꢁ3
DB98-27204A.indd
13
2007-1-23
9:18:44
DB98-27204A.indd
14
2007-1-23
9:18:45
|