Large Format Display
User’s Manual
MultiSync C431
MultiSync C501
MultiSync C551
MODEL: C431, C501, C551
Please find your model name in the label on the rear side of the monitor.
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address:
500 Park Boulevard, Suite 1100
Itasca, Illinois 60143
(630) 467-3000
Tel. No.:
Type of Product:
Display Monitor
Equipment Classification: Class B Peripheral
Model:
C431
C501
C551
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
Cable information
CAUTION: Use the attached specified cables with this color monitor so as not to interfere with radio and television reception.
For mini D-Sub 15-pin, please use a shielded signal cable with ferrite core.
For HDMI, DisplayPort, USB and D-Sub 9-pin, please use a shielded signal cable.
Use of other cables and adapters may cause interference with radio and television reception.
FCC Information
1. Please use the supplied power cord or equivalent to ensure FCC compliance.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and
Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C.,
20402, Stock No. 004-000-00345-4.
Windows is a registered trademark of Microsoft Corporation.
NEC is a registered trademark of NEC Corporation.
DisplayPort and DisplayPort Compliance Logo are trademarks owned by Video Electronics Standards
Association in the United States and other countries.
All other brands and product names are trademarks or registered trademarks of their respective owners.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks
or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and
other countries and areas.
microSD and microSD SDHC logos are trademarks of SD-3C, LLC.
CRESTRON and CRESTRON ROOMVIEW are trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and other countries.
GPL/LGPL Software Licenses
The product includes software licensed under GNU General Public License (GPL), GNU Lesser General Public License (LGPL),
and others.
For more information on each software, see “readme.pdf” inside the “about GPL&LGPL” folder on the supplied CD-ROM.
Adobe and the Adobe logo are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or
other countries.
English-1
Important Information
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE
PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO
FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET.
DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been
included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is
not supplied with this equipment, please contact NEC. For all other cases, please use the power cord with the plug style that
matches the power socket where the monitor is located. The compatible power cord corresponds to the AC voltage of the power
outlet and has been approved by, and complies with, the safety standards in the country of purchase.
This equipment is designed to be used in the condition of the power cord connected to earth. If the power cord is not connected
to the earth, it may cause electric shock. Please make sure the power cord is earthed properly.
European
Continental
Plug Type
North America
U.K.
Chinese
Japanese
Plug Shape
U.S.A./
Canada
Region
Voltage
EU
U.K.
230
China
220
Japan
100
Taiwan
110
120*
230
* When operating this monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply
voltage of the AC power outlet being used.
NOTE:
This product can only be serviced in the country where it was purchased.
Use the power cord which has BSMI mark at both ends when you use this monitor in Taiwan.
•
•
The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment.
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.
English-2
Safety Precautions, Maintenance & Recommended Use
•
Do not use monitor under rapid temperature and humidity
change condition and avoid cold air from air-conditioning
outlet directly, as it may shorten the lifetime of the monitor
or cause condensation. If condensation of water has
happened, let the monitor stand unplugged until the
condensation has disappeared.
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTI-FUNCTION MONITOR:
•
DO NOT OPEN THE MONITOR. There are no user
serviceable parts inside and opening or removing covers
may expose you to dangerous shock hazards or other
risks. Refer all servicing to qualified service personnel.
Connecting to a TV*
•
Cable distribution system should be grounded (earthed)
in accordance with ANSI/NFPA 70, the National Electrical
Code (NEC), in particular Section 820.93, Grounding of
Outer Conductive Shield of a Coaxial Cable.
•
•
Do not bend, crimp or otherwise damage the power cord.
Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or fire.
•
The screen of the coaxial cable is intended to be
connected to earth in the building installation.
•
The power supply cord you use must have been
approved by and comply with the safety standards of your
country. (e.g. Type H05VV-F 3G 0.75 mm2 should be used
in Europe).
Under the following conditions immediately disconnect your
monitor from the wall outlet and refer servicing to qualified
service personnel:
•
•
In the UK use a BS-approved power cord with a molded
plug having a black (5 A) fuse installed for use with this
monitor.
•
•
If the power supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the
monitor.
The power cable connector is the primary means of
detaching the system from the power supply. The monitor
should be installed close to a power outlet, which is easily
accessible.
•
•
If the monitor has been exposed to rain or water.
If the monitor has been dropped or the cabinet has been
damaged.
•
•
Do not spill any liquids into the cabinet or use your
monitor near water.
•
•
If you notice any structural damage such as cracks or
unnatural wobbling.
Do not insert objects of any kind into the cabinet slots
as they may touch dangerous voltage points, which can
be harmful or fatal, or may cause electric shock, fire or
equipment failure.
If the monitor does not operate normally by following
operating instructions.
Recommended Use
•
•
Do not place this product on a sloping or unstable cart,
stand or table, as the monitor may fall, causing serious
damage to the monitor.
Ergonomics
To realize the maximum ergonomic benefits, we recommend
the following:
Do not mount this product upside down for an extended
period of time as it may cause permanent damage to the
screen.
•
For the monitor’s optimum performance, allow 20 minutes
for warming up. Avoid reproduction of still patterns on
the monitor for long periods of time to avoid image
persistence (after image effects).
•
•
•
Do not use the monitor outdoors.
If glass is broken, handle with care.
•
•
•
Rest your eyes periodically by focusing on an object at
least 5 feet away. Blink often.
For reliable performance and long useful life of this
product, it is mandatory to not cover any vents on the
monitor.
Position the monitor at a 90° angle to windows and other
light sources to minimize glare and reflections.
•
•
•
If monitor or glass is broken, do not come in contact with
the liquid crystal and handle with care.
Adjust the monitor’s brightness, contrast and sharpness
controls to enhance readability.
Allow adequate ventilation around the monitor, so that
heat can properly dissipate.
•
•
Get regular eye checkups.
Use the preset Size and Position controls with standard
Do not block ventilated openings or place the monitor
near a radiator or other heat sources.
signals.
•
•
•
Use the preset Color Setting.
Use non-interlaced signals.
•
•
Do not put anything on top of the monitor.
Handle with care when transporting. Save packaging for
transporting.
Do not use primary color blue on a dark background, as
it is difficult to see and may produce eye fatigue due to
insufficient contrast.
•
•
It is recommended to wipe holes clean a minimum of
once a month.
•
Suitable for entertainment purposes at controlled
luminous environments, to avoid disturbing reflections
from the screen.
To ensure the monitor’s reliability, please clean the holes
at the rear side of the cabinet at least once a year to
remove dirt and dust.
•
•
When using a LAN cable, do not connect to a peripheral
device with wiring that might have excessive voltage.
Do not use the monitor in high temperature, humid, dusty,
or oily areas.
* The product you purchased may not have this feature.
English-3
Cleaning the LCD Panel
•
When the LCD panel is dusty, please gently wipe with a
soft cloth.
•
Clean the LCD monitor surface with a lint-free, non-
abrasive cloth. Avoid using any cleaning solution or glass
cleaner!
•
•
•
Please do not rub the LCD panel with hard material.
Please do not apply pressure to the LCD panel surface.
Please do not use OA cleaner as it will cause
deterioration or discoloration on the LCD panel surface.
Cleaning the Cabinet
•
•
•
Unplug the power supply
Gently wipe the cabinet with a soft cloth
To clean the cabinet, dampen the cloth with a neutral
detergent and water, wipe the cabinet and follow with a
dry cloth.
NOTE:
DO NOT clean with benzene thinner, alkaline
detergent, alcoholic system detergent, glass
cleaner, wax, polish cleaner, soap powder, or
insecticide. Rubber or vinyl should not be in
contact with the cabinet for an extended period
of time. These types of fluids and materials can
cause the paint to deteriorate, crack or peel.
English-4
Installation
For box contents, please refer to the printed contents sheet
provided in the box.
•
•
When used in a video wall configuration for a longer
time, slight expansion of the monitors may happen due to
temperature changes. Due to this it is recommended that
over one millimeter gap is kept between adjacent monitor
edges.
This device cannot be used or installed without the Tabletop
Stand or other mounting accessory for support. For proper
installation it is strongly recommended to use a trained,
NEC authorized service person. Failure to follow NEC
standard mounting procedures could result in damage to the
equipment or injury to the user or installer. Product warranty
does not cover damage caused by improper installation.
Failure to follow these recommendations could result in
voiding the warranty.
When installing, do not apply pressure to the screen or
excessive force to any part of the monitor by pushing
or leaning on it. This may cause the monitor to become
distorted or damaged.
To prevent the LCD monitor from falling off from the wall or
ceiling, NEC strongly recommends using a safety wire.
Please install LCD monitor in a spot of the wall or ceiling
strong enough to support the monitor.
Mounting
DO NOT mount the monitor yourself. Please ask your
supplier. For proper installation it is strongly recommended to
use a trained, qualified technician. Please inspect the location
where the unit is to be mounted. Mounting on wall or ceiling
is the customer’s responsibility. Not all walls or ceilings are
capable of supporting the weight of the unit. Product warranty
does not cover damage caused by improper installation, re-
modeling, or natural disasters. Failure to comply with these
recommendations could result in voiding the warranty.
Prepare the LCD monitor using mounting accessories such
as hook, eyebolt or mounting parts and then secure the LCD
monitor with a wire. The safety wire must not be tight.
CAUTION: Do not attempt to hang the monitor using an
installation safety wire. The monitor must be
properly installed on a VESA compatible mount.
Please make sure the mounting accessories are strong
enough to support the LCD monitor before mounting it.
DO NOT block ventilated openings with mounting
accessories or other accessories.
Landscape installation for safety wire
For NEC Qualified Personnel:
To ensure safe installation, use two or more brackets to
mount the unit. Mount the unit to at least two points on the
installation location.
Please note the following when mounting
on wall or ceiling
•
When using mounting accessories other than those that
are NEC approved, they must comply with the VESA-
compatible (FDMlv1) mounting method.
•
•
NEC recommends mounting interfaces that comply with
UL1678 standard in North America.
NEC strongly recommends
using size M6 screws
Mounting
Bracket
Unit
No gap
(10-12 mm + thickness
of bracket and washers in
length). If using screws
longer than 10-12 mm,
check the depth of the hole.
(Recommended Fasten
No thread
4 mm
Washers
VESA Mounting Interface (M6)
Portrait installation
for safety position
under
8.5 mm
Screw
Installing a wire to a monitor
10-12 mm
Thickness
of bracket
and washers
Please use eyebolts to install a wire to the monitor.
Force: 470 - 635N•cm). Bracket
hole should be under 8.5 mm.
•
Prior to mounting, inspect the installation location to
ensure that it is strong enough to support the weight of
the unit so that the unit will be safe from harm.
Less than 12 mm
•
•
For detailed information, refer to the instructions included
with the mounting equipment.
Make sure that there is no gap between the monitor and
the bracket.
English-5
LED Indicator
Changing NEC logo ornament position
When using the monitor in the portrait position, the NEC logo
ornament position can be changed.
Removing the logo ornament: unscrew the installed screw
then take off the logo ornament.
Attaching the logo ornament: adjust the protrusions inside of
the logo ornament into the protrusion hole on the bezel. Make
sure the hole for the screw on the logo ornament and the
hole for the screw on the bezel are aligned. Install the logo
ornament with the screw, which is used for installing the logo
ornament.
(Recommended Fasten Force: 30-40N•cm).
Protrusion hole
Screw hole
Protrusion hole
Screw hole
Protrusions
Inside of NEC logo ornament
CAUTION: Do not use any other screw to install the logo
ornament.
Height adjustment
Attaching Mounting Accessories
1. The lines on the stand pole are indicators of the height
adjustment. Please adjust the pipe to the lines.
The monitor is designed for use with the VESA mounting
system.
1. Attach Mounting Accessories
Be careful to avoid tipping the monitor when attaching
accessories.
Pipe
VESA Mounting Interface (M6)
C551 High/Low
C501
C431
Adjust the pipe to a line.
Stand pole
2. Please install the stand pole and the pipe with included
screws. Please screw the two screw holes at the pipe.
300 mm
Pipe
Mounting accessories can be attached with the monitor in
the face down position. To avoid damaging the front face,
place the protective sheet on the table underneath the LCD
monitor. The protective sheet was wrapped around the LCD
monitor in the original packaging. Make sure there is nothing
on the table that can damage the monitor.
Stand pole
NOTE:
Installing the monitor at the wrong height can
cause tipping.
Please install your monitor at proper height.
When using mounting accessories other than NEC compliant
and approved, they must comply with the VESA Flat Display
Mounting Interface Standard (FDMI).
3. Ventilation Requirements
When mounting in an enclosed space or recessed area,
leave adequate room between the monitor and the enclosure
to allow heat to disperse, as shown below.
NOTE:
Prior to installation, be sure to place the monitor
on a flat area with adequate space.
2. Installing and removing the optional
table top stand
100 mm
CAUTION: Installing and removing the stand must be done
by two or more people.
For installation, follow the instructions included with the
stand or mounting equipment. Use only those devices
recommended by the manufacturer.
30 mm
NOTE:
ONLY use screws which are supplied with the
optional table top stand.
When installing, do not put your hands on the
monitor or apply force. The monitor may become
distorted.
100 mm
Must be under 40 Degree Celsius.
When installing the LCD monitor stand, handle the unit with
care to avoid pinching your fingers.
Allow adequate ventilation or provide air conditioning around
the monitor, so that heat can properly dissipate away from
the unit and the mounting equipment; especially when you
use monitors in a multiple screen configuration.
NOTE:
Use the ST-401. Please refer to the ST-401
user’s manual for more detail.
NOTE:
The sound quality of the internal speakers will be
different depending on the acoustics of the room.
English-7
Parts Name and Functions
Control Panel
A Power Button (
)
H Menu/Exit Button (MENU/EXIT)
Switches the power on/standby. See also page 16.
Activates the OSD menu when the OSD menu is turned off.
Acts as a back button within the OSD to move to the previous
OSD menu.
Acts as an EXIT button to close the OSD when on the main
menu.
B Mute Button (MUTE)
Switches the audio mute on/off.
C Input/Set Button (INPUT/SET)
INPUT: Toggle switches between below inputs.
[DisplayPort], [HDMI1], [HDMI2], [HDMI3],
[VGA (YPbPr/RGB)], [VIDEO], [MP]. These are available
inputs only, shown as their factory preset name.
SET: When OSD (On Screen Display) is shown, this button
acts as a “set button” when you make a selection.
I Remote Control Sensor and Power Indicator
Receives the signal from the remote control (when using the
Glows blue when the LCD monitor is in active mode*.
Green and Amber blink alternately when the “SCHEDULE
SETTINGS” function is enabled*1.
When a component failure is detected within the monitor, the
indicator will blink red or blink a combination of red and blue.
* If “OFF” is selected in the “POWER INDICATOR”
active mode.
D Plus Button (+)
Increases the audio output level when the OSD menu is
turned off.
Acts as (+) button to increase the adjustment within OSD
menu.
*1 If “OFF” is selected in the “SCHEDULE INDICATOR”
E Minus Button (-)
Decreases the audio output level when the OSD menu is
turned off.
Acts as (-) button to decrease the adjustment within OSD
menu.
J Room Light Sensing Sensor
Detects the level of ambient light, allowing the monitor
to make automatic adjustments to the backlight setting,
resulting in a more comfortable viewing experience. Do not
cover this sensor. See page 34.
F Up Button (
)
Activates the OSD menu when the OSD menu is turned off.
Acts as button to move the highlighted area up to select
adjustment items within the OSD menu.
G Down Button (
)
Activates the OSD menu when the OSD menu is turned off.
Acts as button to move the highlighted area down to select
adjustment items within the OSD menu.
English-8
Terminal Panel
USB Upstream
A AC IN Connector
I LAN port IN (RJ-45)
Connects with the supplied power cord.
B Main Power Switch
J USB port
On/Off switch to turn main power ON/OFF.
USB (2A): USB storage device port.
To use the Media Player, please connect USB storage device
C microSD Card Slot
Insert a microSD memory card. To use the Media Player,
please connect a microSD memory card to this port
K RS-232C IN (D-Sub 9-pin)
Connect RS-232C input from external equipment such as a
To install the microSD card slot cover, pleas e refer to
computer in order to control RS-232C functions.
L Remote IN/OUT
Use to connect to other displays to create the “daisy-chain”
function. Use the optional sensor unit by connecting it to your
monitor.
D DisplayPort IN
DisplayPort signals input.
E HDMI IN1/IN2/IN3
NOTE: Do not use this connector for any other purpose.
Digital HDMI signals input.
M Audio OUT
FVGA IN (Mini D-Sub 15-pin)
Audio signal output from the AUDIO IN1/IN2, DisplayPort and
HDMI to an external device (stereo receiver, amplifier, etc.).
NOTE: This connector is not a Headphone terminal.
Analog RGB signals input from a personal computer or from
other RGB equipment. This input can be used with an RGB
or YPbPr source. Please select signal type in TERMINAL
N Internal Speaker
NOTE: When you use this connector for YPbPr, please use a
suitable signal cable. If you have any questions, please ask
your supplier.
O Security Slot
Security and theft protection lock compatible with Kensington
security cables/equipment.
For products, visit Kensington’s website.
GVideo IN
Composite video signal input.
P Rating Label
H Audio IN1/IN2
Audio signal input from external equipment such as a
computer or player.
English-9
Wireless Remote Control
I EXIT Button
Returns to the previous menu within the OSD menu.
J UP/DOWN Button (
/
)
Acts as button to move the highlighted area up or down
to select adjustment items within the OSD menu.
K MINUS/PLUS (-/+) Button
Increases or decreases the adjustment level within the OSD
menu settings.
L SET/POINT ZOOM Button
SET: When OSD is shown, this button acts as “set button”
when you make a selection.
POINT ZOOM: When OSD is not shown, this button acts as
“point zoom button”.
MVOLUME UP/DOWN Button (VOL +/-)
Increases or decreases the audio output level.
N CH/ZOOM UP/DOWN Button (CH/ZOOM +/-)
Increases or decreases the POINT ZOOM level.
O GUIDE Button (This button does not work)
P MUTE Button
Turns on/off the mute function.
Q PICTURE MODE Button
Selects the picture mode, [HIGHBRIGHT], [STANDARD],
[sRGB], [CINEMA], [CUSTOM1], [CUSTOM2]. See page 25.
A POWER ON/STANDBY Button
Switches the power on/standby.
HIGHBRIGHT: For moving images such as DVD.
STANDARD: For images.
sRGB: For text based images.
CINEMA: For movies.
CUSTOM1 and CUSTOM2: Custom setting.
B INPUT Button
Selects the input signal.
Input signal for the Media Player is shown as MP.
R ASPECT Button
Selects the picture aspect, [FULL], [WIDE]*, [1:1], [ZOOM]
C OPTION MENU Button (This button does not work)
D KEYPAD
* HDMI1, HDMI2, HDMI3, VGA (YPbPr) inputs only.
Press the buttons to set and change passwords, change
channel and set REMOTE ID.
Below buttons are used for CEC (Consumer Electronics
S AUDIO INPUT Button
Selects the audio input source [IN1], [IN2], [DisplayPort],
[HDMI1], [HDMI2], [HDMI3], [MP].
(See page 18): 1
, 2 , 3
, 5 , 6
.
T STILL Button
E ENT Button (This button does not work)
ON/OFF button: Activates/deactivates still picture mode.
NOTE: This function deactivates when selecting SCREEN
SAVER, POINT ZOOM, TILE MATRIX.
Confirm the AUTO PLAY FOLDER in MediaPlayer.
F DISPLAY Button
Turns on/off the information OSD. See page 24.
CLOSED CAPTION is not available when STILL is active.
If you lock remote control buttons using the IR LOCK
SETTINGS function, you can unlock the buttons by holding
down this DISPLAY button for more than 5 seconds.
IMAGE FLIP Button (This button does not work)
ACTIVE PICTURE Button (This button does not work)
MULTI PICTURE Button (This button does not work)
G MENU Button
Turns on/off the menu mode.
REMOTE ID Button
Activates the REMOTE ID function. See page 37.
H AUTO SET UP Button
MTS Button (This button does not work)
Button (This button does not work)
NOTE:
The buttons with no explanation do not function.
English-10
Operating Range for the Remote
Control
Point the top of the remote control toward the LCD monitor’s
remote control sensor during button operation.
Use the remote control within a distance of about 7 m (23 ft.)
from the remote control sensor, or at a horizontal and vertical
angle of within 30° and within a distance of about 3.5 m (10 ft.).
Caution: Important, the remote control
system may not function when
direct sunlight or strong
illumination strikes the
remote control sensor, or
when there is an object in
the path.
Handling the remote control
•
•
Do not expose to strong shock.
Do not allow water or other liquid to
splash on the remote control. If the
remote control gets wet, wipe it dry immediately.
•
•
Avoid exposure to heat and steam.
Except to install the batteries, do not open the remote
control.
English-11
Setup
1. Determine the installation location
CAUTION: Installing your LCD monitor must be done by a
qualified technician. Contact your supplier for
more information.
3. Connect external equipment
•
To protect the external equipment, turn off the main power
before making connections.
•
Refer to the user’s manual of your equipment for further
information.
CAUTION: MOVING OR INSTALLING THE LCD MONITOR
MUST BE DONE BY TWO OR MORE PEOPLE.
Failure to follow this caution may result in injury if
the LCD monitor falls.
NOTE:
Do not connect/disconnect cables when turning
on the monitor or other external equipment, as this
may result in a loss of the monitor image.
CAUTION: Do not mount or operate the monitor upside
down.
4. Connect the supplied power cord
•
•
•
The equipment should be installed close to an easily
CAUTION: This LCD monitor has internal temperature
sensors.
accessible power outlet.
If the LCD monitor becomes overheated, a
“Caution” warning will appear. If the “Caution”
warning appears, stop using the unit and allow it
to cool.
Please fasten the power cord to the LCD monitor by
attaching the screw and clamp.
Fully insert the prongs into the power outlet socket.
A loose connection may cause image degradation.
If the LCD monitor is used in an enclosed area
or if the LCD panel is covered with a protective
screen, please check the inside temperature of
the monitor by using the “HEAT STATUS” control
NOTE:
Please refer to the “Safety Precautions and
Maintenance” section of this user’s manual for
proper selection of an AC power cord.
(Recommended Fasten Force: 139 - 189N•cm).
IMPORTANT: Lay the protective sheet beneath the
monitor, so as not to scratch the LCD panel.
The protective sheet was wrapped around the
monitor when it was packaged.
2. Install the remote control batteries
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
Screw
Clamp
A. Press and slide to open the cover.
B. Align the batteries according to the (+) and (–) indications
inside the case.
5. Switch on the power of all the attached
external equipment
C. Replace the cover.
When connected with a computer, switch on the power of the
computer first.
CAUTION: Incorrect usage of batteries can result in leaks or
bursting.
6. Operate the attached external equipment
Show the signal on the screen from the desired input source.
NEC recommends the following battery use:
•
Place “AAA” size batteries matching the (+) and (-) signs
on each battery to the (+) and (-) signs of the battery
compartment.
7. Adjust the sound
•
•
Do not mix battery brands.
Make volume adjustments when required.
Do not combine new and old batteries. This can shorten
battery life or cause liquid leakage of batteries.
8. Adjust the screen
Make adjustments to the image position, if necessary.
•
•
Remove dead batteries immediately to prevent battery
acid from leaking into the battery compartment.
Do not touch exposed battery acid, it may injure your skin.
9. Adjust the image (See page 28)
Make adjustments such as backlight or contrast when
required.
NOTE:
If you do not intend to use the Remote Control for
a long period of time, remove the batteries.
English-12
Connections
NOTE:
Do not connect or disconnect cables when turning on the monitor’s main power or other external equipment’s power,
as this may result in a loss of the monitor image.
NOTE:
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.
Before making connections:
*
*
*
First turn off the power of all the attached equipment and make connections.
Refer to the user’s manual included with each separate piece of equipment.
We strongly recommend connecting or disconnecting a USB storage device or a microSD memory card to the monitor when
the monitor’s main power is off.
Wiring Diagram
Stereo Amplifier
DVD Player
(component)
Devices that
require power
supply:
Ex:
DVD Player
MultiPresenter
Stick
Stereo Amplifier
Computer (Analog)
AV Amplifier
DVD Player (HDMI) or
Computer (HDMI)
Computer (DisplayPort)
VCR Player or
DVD Player (Video)
Solid lines = video signal
Computer
Dashed lines = audio signal
Dotted lines = other signal
VCR Player or
DVD Player
*: Multiple monitors can have their REMOTE IN/OUT ports daisy chained together. This allows one optional remote sensor kit to be used for multiple monitors.
Connected
equipment
Setting in
TERMINAL SETTINGS
Input button in
remote control
DisplayPort
HDMI1
HDMI2
HDMI3
VGA (RGB/YPbPr)
VGA (RGB/YPbPr)
VIDEO
Connecting terminal
Input signal name
Connecting audio terminal
DisplayPort IN
HDMI IN1
HDMI IN2
VIDEO LEVEL: RAW/EXPAND*1
VIDEO LEVEL: RAW/EXPAND*1
VIDEO LEVEL: RAW/EXPAND*1
VIDEO LEVEL: RAW/EXPAND*1
VGA MODE: RGB
DisplayPort
HDMI1
HDMI2
DisplayPort
HDMI1
HDMI2
AV*2
HDMI IN3
HDMI3
HDMI3
VGA (RGB, YPbPr)
VGA (RGB, YPbPr)
VIDEO IN
DisplayPort IN
HDMI IN1
HDMI IN2
HDMI IN3
VGA (RGB, YPbPr)
VGA (RGB, YPbPr)
VIDEO IN
VGA (RGB)
VGA (YPbPr)
VIDEO
DisplayPort
HDMI1
HDMI2
HDMI3
VGA (RGB)
VGA (YPbPr)
VIDEO
IN1/IN2
IN1/IN2
IN1/IN2
DisplayPort
HDMI1
HDMI2
HDMI3
IN1/IN2
IN1/IN2
IN1/IN2
VGA MODE: YPbPr
—
VIDEO LEVEL: RAW/EXPAND*1
VIDEO LEVEL: RAW/EXPAND*1
VIDEO LEVEL: RAW/EXPAND*1
VIDEO LEVEL: RAW/EXPAND*1
VGA MODE: RGB
DisplayPort
HDMI1
HDMI2
PC*3
HDMI3
VGA (RGB/YPbPr)
VGA (RGB/YPbPr)
VIDEO
VGA MODE: YPbPr
—
*1: Please set appropriate setting for input signal.
English-14
Connecting a Personal Computer
Connecting your computer to your LCD monitor will enable you to reproduce your computer’s video signal output.
Some display cards may not be able to support the required resolution for proper image reproduction.
Your LCD monitor shows proper image by adjusting the factory preset timing signal automatically.
<Typical factory preset signal timing>
Scanning frequency
DisplayPort
1.1a
Yes
Resolution
VGA
HDMI
Remarks
Horizontal
31.5 kHz
37.9 kHz
48.4 kHz
45.0 kHz
47.8 kHz
49.7 kHz
60.0 kHz
64 kHz
Vertical
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
640 x 480
800 x 600
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
1024 x 768
1280 x 720
1280 x 768
1280 x 800
1280 x 960
1280 x 1024
1360 x 768
1366 x 768
1400 x 1050
1440 x 900
1600 x 1200
1680 x 1050
1920 x 1080
1920 x 1200
47.7 kHz
47.7 kHz
65.3 kHz
55.9 kHz
75.0 kHz
65.3 kHz
67.5 kHz
74.6 kHz
Compressed image
Recommended resolution
Compressed image
Connecting a Player or Computer with HDMI
•
•
•
•
•
•
Please use an HDMI cable with the HDMI logo.
It may take a moment for the signal to appear.
Some display cards or drivers may not display an image correctly.
When you use a computer with HDMI, please set OVER SCAN to “AUTO” or “OFF” (see page 28).
Please check display card when image is compressed with 1920 x 1080.
To output HDMI audio, set [HDMI1], [HDMI2] or [HDMI3] at AUDIO INPUT in the OSD or choose [HDMI1], [HDMI2] or
[HDMI3] by the remote control AUDIO INPUT button.
•
If the monitor’s main power is turned on after a connected computer is turned on, sometimes images are not displayed.
In this case, please turn off the computer then turn it on again.
Connecting a Computer with DisplayPort
•
•
•
•
•
Please use a DisplayPort cable with the DisplayPort compliance logo.
It may take a moment for the signal to appear.
When connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not appear.
Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.
To output DisplayPort audio, set [DisplayPort] at AUDIO INPUT in the OSD or choose [DisplayPort] by the remote control
AUDIO INPUT button.
•
If the monitor’s main power is turned on after a connected computer is turned on, sometimes images are not displayed.
In this case, please turn off the computer then turn it on again.
Connecting a USB device
USB (2A): USB downstream port (Type-A).
To use the Media Player function, please use this port.
•
•
•
•
Please make sure the connector shape and orientation is correctly aligned when connecting the USB device or cable.
Please refer to the specifications page for power supply information (see page 53, page 54 and page 55).
When you use the USB (2A) port for power supply, please use a USB cable that supports 2A.
Do not bind the USB cable. It may cause heat or fire.
English-15
Basic Operation
Power ON and OFF Modes
The LCD monitor power indicator will turn blue while powered on.
NOTE:
The Main Power switch must be in the ON position in order to power up the monitor using the remote control or the
Power button.
OFF
Main Power Switch
ON
Power Button
Using the remote control
POWER ON button
English-16
Power Indicator
LED indicator
Aspect
For VIDEO, VGA (RGB, YPbPr)
status and
lighting pattern
Condition
Recovery
FULL
ZOOM
NORMAL
Glowing blue
Blinking green*1
Normal
For DisplayPort
FULL 1:1
The monitor has detected no
signal input after a certain
amount of time has passed
when INPUT DETECT is not
NONE, STANDBY USB POWER
is ENABLE, or QUICK TURN
ON is ENABLE.
ZOOM
NORMAL
For HDMI1, HDMI2, HDMI3
FULL WIDE 1:1 ZOOM
NORMAL
1. Turn on the monitor
by the remote
control or the
Glowing amber
Blinking amber
Glowing red
The monitor has detected no
AV signal input [with network
signal input] after a certain
amount of time has passed
when INPUT DETECT is NONE,
STANDBY USB POWER and
QUICK TURN ON are ENABLE.
monitor button.
Aspect ratio
of image
Recommended selection
for picture aspect*3
Unchanged view*3
2. Send an AV signal
input to the monitor.
NORMAL
4:3
The monitor has detected no AV
signal input [no network signal
input] after a certain amount of
time has passed when INPUT
DETECT is NONE, STANDBY
USB POWER and QUICK TURN
ON are ENABLE.
FULL
Squeeze
Letterbox
Turn off the monitor by the
remote control or the monitor
button.
Turn on the monitor by
the remote control or
the monitor button.
WIDE
*1: Time setting for AUTO POWER SAVE is available at POWER SAVE
NOTE:
If the indicator is blinking red in a combination
of long and short, a certain failure might have
occurred, please contact your supplier.
*3 Grey areas indicate unused portions of the screen.
NORMAL: Reproduces the aspect ratio that is sent from the
source.
FULL: Fills the entire screen.
Using Power Management
WIDE: Expands a 16:9 letterbox signal to fill the entire
screen.
This LCD monitor follows the VESA approved DPM (Display
Power Management) function.
The power management function is an energy saving
function that automatically reduces the power consumption
of the monitor when the keyboard or the mouse has not been
used for a fixed period.
This allows your LCD monitor to enter a Power Management
mode if the monitor’s POWER SAVE function is set to
ENABLE, and a certain amount of time has passed since the
monitor recognized “no signal input”. It will increase the life
and decrease the power consumption of the monitor.
1:1: Shows the image in a 1 by 1 pixel format.
ZOOM
The image can be expanded beyond the active screen area.
The image which is outside of the active screen area is not
shown.
ZOOM
NOTE:
Depending on the computer and display card
used, this function may not operate.
After the video signal was lost, the monitor
automatically goes into OFF at a preset time
period.
ZOOM
English-17
Media Player
Plays saved data, such as still and motion images, BGM (Background Music), on a USB storage device or microSD memory
card connected to the monitor.
Top screen of the viewer
•
•
Select [SETTINGS] to change the Media Player settings.
While “AUTO PLAY” has been set to SLIDESHOW in SETTINGS, the monitor starts performing “AUTO PLAY” by the
operation below:
- When connecting a USB storage device to the USB (2A) port, with the monitor already powered ON and the Media Player
top screen displayed.
- When the input signal is changed to MP, with a USB storage device already connected to the USB (2A) port of the monitor.
For starting “AUTO PLAY”, the system will automatically search the folder which is set in the AUTO PLAY settings FOLDER
field, in the USB storage device and then display found still images or movies. The images and movies will be displayed in the
“Sorted” order.
NOTE:
Only 1 USB storage device can be recognized by the viewer.
A window will appear when you press the control panel buttons while the Media Player is active. You can select to control either
the OSD menu or the Media Player from the window that opens.
Media Player contents are not played while TILE MATRIX is active.
If a monitor is used in portrait position, please set OSD ROTATION to PORTRAIT. Image orientation is changed according to
what you set at OSD ROTATION.
If you play a motion image with the monitor position as portrait, please use the motion image which is rotated anticlockwise
by 90°.
Displayable/playable files
Still
Supported formats
File extension
.jpg, .jpeg, .jpe
.png
Supported
Baseline, Progressive, RGB, CMYK
Interlace, α channel
Motion image
Supported formats
File extension
Video codec
Audio codec
.mpg, .mpeg
MPEG1, MPEG2
MPEG Audio Layer3 (Abbreviation: MP3)
AAC-LC (Abbreviation: AAC), LPCM
.wmv
.mp4
H.264, WMV
H.264
MP3, WMA Standard, WMA 9/10 Professional
MP3, AAC
MP3, AAC
MP3, AAC
.mov
H.264
.flv, .f4v
H.264
English-18
BGM
Supported formats
File extension
.wav
Audio codec
LPCM
.mp3
MP3
Information
Item
Conditions
JPEG
PNG
Resolution
5000x5000
4000x4000
MPEG1
MPEG2
H.264
WMV
-
480@30fps
MP@ML, MP@HL, 1080p@30fps / 1080i@60fps
High profile Lv.4.2, 1080p@30fps / 1080i@60fps
Advanced@L3, Simple&Main
Up to 15Mbps
Video bit date
Audio sampling rate
Audio bit rate
-
Up to 48KHz
MP2
Up to 384Kbps
MP3
Up to 320Kbps
AAC
Up to 1440Kbps
NOTE:
Depending on the file, it may not play even when it satisfies all above mentioned conditions.
Depending on network environments, the type of USB storage device, and file bitrate, it may not play still image files.
You cannot play DRM (Digital Right Management) files.
The maximum resolution for a motion image is 1920 (Horizontal) x 1080 (Vertical).
Compatible microSD memory card
Format a microSD memory card in the FAT32 format or FAT16 format.
Refer to the computer’s instruction user’s manual or Help file on how to format a microSD memory card.
Information
Up to 32GB microSDHC is supported.
NOTE:
It is not guaranteed to work with all microSD memory card sold commercially.
microSD with CPRM is not supported.
microSD UHS-1 or UHS-2 are not supported.
•
•
When inserting a microSD memory card, please make sure of the microSD memory card direction then insert it correctly.
When ejecting a microSD memory card from the microSD card slot, press the center of the microSD memory card then take
it out.
Installing microSD card slot cover
To secure your microSD memory card, we recommend you install the microSD card slot cover.
Please insert the edge of the microSD card cover to the hole. (Recommended Fasten Force: 139 - 189N•cm).
Hole
microSD card cover is set.
English-19
Compatible USB memory
Format a USB memory in the FAT32 format or FAT16 format for using it in the Media Player. Refer to the computer’s instruction
user’s manual or Help file on how to format a USB memory.
Please use a USB memory with this monitor in accordance with the drawing below.
If the physical size of the USB device is larger than than the supported sizes listed below, please use a USB extension cable.
C431: under 70 mm
C501: under 145 mm
C551: under 200 mm
USB memory
Extension cable
Under 5.5 mm
NOTE:
Check the format if this device cannot recognize the connected USB memory.
It is not guaranteed to work with all USB memories sold commercially.
File display screen
The files can be displayed using either icons or thumbnails in the Media Player.
Icon display
RETURN
Goes back one subsequent level higher.
PAGE UP
Displays a list of the previous files.
Displays a list of the next files.
Displays the setting screen.
PAGE DOWN
SETTINGS
THUMBNAILS/ICON Switches between thumbnail display and icon display.
SORT
Changes the order to display files by name (filename), type (file extension), date (date of creation), or size
(file capacity). The default sorting order is by “Name”.
EJECT
Disconnects from the USB storage device or the microSD memory card inserted to the monitor. Please
select EJECT when file list is displayed.
NOTE:
The maximum number of files that can be displayed in a folder including folder icons is 300.
A folder hierarchy is shown up to level 16.
The icon of a file whose type cannot be determined is indicated by a “?”.
Depending on the file, thumbnail cannot be displayed.
English-20
Slideshow display
•
•
Select a folder that contains images or movies.
A slideshow can be displayed using “MANUAL” in which the images are switched by operating a button on the remote
control, or “AUTO” in which the images are switched automatically at a set interval (PLAY MODE is “AUTO”).
•
•
•
The default factory setting is “MANUAL”. To perform “AUTO”, set the “PLAY MODE” to “AUTO”.
The images will be displayed in the order selected under “Sort” on the file display screen.
When still images in high resolutions are displayed as the Slideshow, it may go back to the file display screen.
Media Player settings
Select the
icon in the file list screen or top screen of the Media Player to display the configuration screen of the Media Player.
The following settings can be configured on the configuration screen.
SLIDESHOW
Menu
Function
SCREEN SIZE
PLAY MODE
INTERVAL
REPEAT
Selects ACTUAL SIZE or BEST FIT.
Selects AUTO or MANUAL.
Sets interval time.
Check the check box to repeat slideshow.
Selects an audio file.
AUDIO FILE
BGM
Check the check box to enable BGM.
PLAY END SCREEN
Selects a setting for when the slideshow finishes.
BLACK SCREEN: When the slideshow finishes, a black screen is displayed.
FILE LIST: When the slideshow finishes, it goes back to the file list screen.
SAVE LAST SCREEN: When the slideshow finishes, the last slideshow image is kept on the screen.
AUTO PLAY
Automatically displays selected folder when the input signal is changed to MP, while “AUTO PLAY” has been set to
SLIDESHOW.
Menu
Function
AUTO PLAY
OFF: Automatic play mode is off.
SLIDESHOW: Automatically plays a selected file.
Select a file by SET/POINT ZOOM button and confirm by ENT button.
FOLDER
PRESET CONTENTS
Plays selected folder when the monitor has no signal input.
Menu
Function
ENABLE
FOLDER
Check the check box to enable preset contents.
Select a file by SET/POINT ZOOM button and confirm by ENT button.
Please press OK to activate above settings.
If OK is not pressed, settings that you set are not activated.
English-21
NETWORK & OTHER SETTINGS
Below are the options for the Network settings and Shared Folder settings for the Media Player.
To select the settings, press the remote control SET/POINT ZOOM button on the NETWORK & OTHER SETTINGS.
NETWORK SETTINGS for Media Player
Menu
Function
IP SETTING
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
DNS
Set these settings.
DNS PRIMARY
DNS SECONDARY
NETWORK INFORMATION for the Media Player displays what you set in the NETWORK SETTINGS for the Media Player.
SHARED FOLDER
There are two settings for configuring the SHARED FOLDER.
Press the remote control SET/ZOOM button to open the shared settings options.
•
SHARED SD CARD SETTINGS
Folders saved in a computer on the network can be copied to the connected microSD memory card using a web browser on
the connected computer.
Menu
ENABLE
USER NAME
PASSWORD
Function
Check the checkbox to enable SHARED SD CARD SETTINGS.
USER NAME is displayed. It is the same name as the monitor name and it is not changeable.
Set password.
Please press OK to activate settings in the SHARED SD CARD SETTINGS.
If OK is not pressed, settings that you set are not activated.
•
SHARED FOLDER SETTINGS.
Folders saved in a computer on the network can be copied to the connected microSD memory card by controlling the
monitor.
Menu
ENABLE
Function
Check the checkbox to enable SHARED FOLDER SETTINGS.
SHARED FOLDER Set the IP address of the network shared folder location that contains the files for copying to the microSD card.
USER NAME
PASSWORD
Set USER NAME which is used when connecting the monitor to the shared folder.
Set password.
Please press OK to activate settings in the SHARED FOLDER SETTINGS.
If OK is not pressed, settings that you set are not activated.
1 to 4 shared folders can be set.
When the connection to the shared folder fails, an error message is displayed and an “x” is displayed in the folder icon.
Carry out the following checks in this case.
- Is the name of the destination folder correct?
- Is the destination folder set for sharing?
- Have access rights been set in the destination folder?
- Are there any displayable files saved in the destination folder?
SHIFT NO SIGNAL
This setting is for a situation when the monitor detects no signal input. If ENABLE is ticked, the monitor goes to no signal status.
The monitor detects no signal when the monitor is in the following conditions:
- After contents or images are played.
- While the monitor is displaying USB window or SD CARD window.
Menu
Function
ENABLE
Check the checkbox to enable SHIFT NO SIGNAL.
Set the time when the monitor goes into no signal after playing detected items.
INTERVAL
Please press OK to activate settings in the SHIFT NO SIGNAL.
If OK is not pressed, settings that you set are not activated.
English-22
Using SHARED SD card SETTINGS
You can copy data to the microSD memory card, such as motion or still images, from a computer connected to the same
network as the monitor.
NOTE:
When the monitor is copying a folder, the LED indicator blinks in red.
When the monitor is in this condition, do not eject a microSD memory card from the monitor and do not turn off the
monitor’s main power. Ejecting the microSD card or turning off the monitor while copying files may corrupt the data.
If you press the STANDBY button on the remote control or the POWER button on the monitor while the LED indicator
is blinking in red, the monitor goes into standby after completing the folder copy.
Files which you can copy are still, motion image and BGM only.
Setting procedure
1. Open the Monitor LAN control of the network connected monitor then select SD-CARD VIEWER.
2. Select SEARCH to display the IP ADDRESS of the currently connected monitor and all compatible monitors on the same
network.
3. Select the IP ADDRESS of the currently connected monitor.
4. Enable upload, delete and sort files that are saved in the microSD memory card connected to the monitor.
Function
1. SELECT UPLOAD.
Press SELECT then choose the files to be copied to the microSD memory card.
File upload window appears and shows the selected files.
Once OK is selected, file uploading starts.
NOTE: Please check the microSD memory card storage capacity before copying files.
STORAGE CAPACITY shows the connected microSD memory card capacity.
2. DELETE.
Select files or folders.
DELETE FOLDERS/FILES window appears.
Once OK is selected, the selected files or folders are deleted.
3. CREATE.
A new folder is created in the microSD memory card connected to the monitor.
Insert folder name and select OK. A maximum of 255 alphanumeric characters is allowed.
English-23
4. RELOAD.
Updates microSD memory card data.
5. THUMB/LIST.
The files can be displayed using either icons or thumbnails.
Displays description of the file or folder if you select thumb name or file name.
6. SORT.
Select sort type. The folders saved in the microSD are sorted based on what you selected for the sort type.
7. Connect to the other monitor’s SD-CARD VIEWER then open them.
By running the SEARCH, as described on the previous page, this window shows all compatible monitors on the same
network as the current monitor.
To open the other monitor’s web page in a new tab, right-click on its IP address. To open the other monitor’s web page in
a new window, left-click on its IP address.
Using CONTENTS COPY
You can copy all data saved in a USB storage device or saved in a shared folder, which is set in the connected computer or a
server, to a microSD memory card.
1. Select CONTENTS COPY at the top screen of the Media Player.
2. Select a USB storage device or a folder.
3. Select OK to start copying. All data saved in the folder or device is copied to the microSD memory card and the original data
saved in the microSD memory card is deleted.
NOTE:
“Out of disk space” is displayed if the microSD memory card storage capacity is not enough to copy selected folders.
When contents copy has occurred, previous data that was saved in the microSD memory card is deleted.
Only devices connected to the monitor are shown.
When the monitor is copying a folder, the LED indicator blinks in red.
When the monitor is in this condition, do not eject the microSD memory card from the monitor and do not turn off the
monitor’s main power. Ejecting the microSD card or turning off the monitor while copying files may corrupt the data.
If you press the STANDBY button on the remote control or the POWER button on the monitor while the LED indicator
is blinking in red, the monitor goes to standby after completing the folder copy.
Using Emergency contents
In case of emergency sends a command to the monitor, from a computer connected to the monitor, to play the emergency
contents folder. Please create an EMERGENCY CONTENTS folder as a root folder in the microSD memory card that is
connected to the monitor.
Instructions for the EMERGENCY CONTENTS can be found on the CD included with the monitor. The file is called
“External_control.pdf”.
Information OSD
The Information OSD provides information such as: Input Source, Picture Size, etc.
Press the DISPLAY button on the remote to bring up the Information OSD.
A
B
C
D
E
Input name
Audio input name
Picture aspect
Input Signal Information
Communication Info
H
English-24
Picture Mode
Select from five different picture modes, either via the OSD menu item PICTURE MODE or using the PICTURE MODE button
on the wireless remote control.
For DisplayPort, VGA (RGB), HDMI1, HDMI2, HDMI3
HIGHBRIGHT
STANDARD
sRGB
CINEMA
CUSTOM1
CUSTOM2
For VGA (YPbYr), VIDEO, MP
HIGHBRIGHT
STANDARD
CINEMA
CUSTOM1
CUSTOM2
PRESET types
PRESET
HIGH BRIGHT
STANDARD
sRGB
PURPOSE
Highest brightness setting.
Standard setting.
The standard color space used for the Internet, Windows® operating systems and digital cameras. Recommended
setting for general color management.
CINEMA
CUSTOM
A setting that boosts dark tones; best suited for movies.
Custom setting.
English-25
OSD (On-Screen-Display) Controls
NOTE:
Some functions may not be available depending on the model or optional equipment.
Input source
Main Menu Icons
MULTI-INPUT
Main Menu Item
Sub Menu
PICTURE:
HIGHBRIGHT
STANDARD
sRGB
PICTUREMODE
BRIGHTNESS
GAMMA
CINEMA
COLOR
CUSTOM1
CUSTOM2
CONTRAST
SHARPNESS
ADJUST
Adjustment Settings
COLORSYSTEM
INPUTRESOLUTION
ASPECT
ADVANCED
RESET
Goto Adjustment
Return
Close
Select
Key Guide
Press UP or DOWN
to navigate to a
sub-menu.
Press SET/POINT
ZOOM to select an
option.
Press UP or DOWN,
Press MENU or EXIT.
PLUS or MINUS to select
the function or setting to
be adjusted.
Remote Control
Press UP or DOWN
to navigate to a
sub-menu.
Press INPUT to
select an option.
Press UP or DOWN, PLUS
or MINUS button to select.
Press EXIT
Control Panel
OSD screen
English-26
OSD Settings
INPUT
DisplayPort
Select input signal.
HDMI1
HDMI2
HDMI3
VGA (RGB/YPbPr)
VIDEO
MP
Displays images or movies saved in microSD memory card or USB storage device. Please refer to the Media
PICTURE
PICTURE MODE
BRIGHTNESS
BACKLIGHT
Select picture mode: [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [CUSTOM1], [CUSTOM2]. See page 25.
Adjusts the overall image and background brightness. Press + or - to adjust.
NOTE: When MODE1 or MODE2 is selected in ROOM LIGHT SENSING, this function cannot be changed.
BRIGHTNESS*1, *4
Adjusts the image brightness in relationship to the background. Press + or - to adjust.
Select a monitor gamma correction for best picture quality. Selection depends on the desired usage.
Gamma correction is handled by the LCD panel.
GAMMA*1
NATIVE
2.2
Typical monitor gamma for use with a computer.
2.4
Good for video (DVD, etc.)
COLOR*1
COLOR*2, *4
Adjusts the color depth of the screen. Press + or - to adjust.
Except for VGA (RGB) input
COLOR
Adjusts the color temperature of the entire screen. A low color temperature will result in a reddish screen. A high
color temperature will make the screen bluish. If TEMPERATURE needs further adjustment, the individual R/G/B/
levels of the white point can be adjusted. To adjust the R/G/B levels, set CUSTOM as COLOR TEMP selection.
NOTE: Predefined 6500k is set as picture mode, a color temperature of 6500k is predefined so it cannot be
changed.
TEMPERATURE*2
COLOR CONTROL*4
Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.
Adjusts the hue of the screen. Press + or - to adjust.
HUE*4
MP, VIDEO inputs only
CONTRAST*1, *4
Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.
Adjusts the crispness of the image. Press + or - to adjust.
SHARPNESS*2, *4
Except for VGA (RGB) input
ADJUST
AUTO SETUP
Automatically adjusts Screen Size, H position, V position, Clock and Phase.
VGA (RGB) input only
AUTO ADJUST
Please use ON normally. When you select OFF, H Position, V Position and Phase are not adjusted automatically
when new timing is detected.
VGA (RGB) input only
H POSITION*3
Controls the horizontal position of the image within the Display area of the LCD.
Press + to move right. Press - to move left.
VGA (RGB), VGA (YPbPr) inputs only
V POSITION*3
Controls the vertical position of the image within the Display area of the LCD.
Press + to move up. Press - to move down.
VGA (RGB), VGA (YPbPr) inputs only
CLOCK
Press + to expand the width of the image on the right of the screen.
Press - to narrow the width of the image on the left.
VGA (RGB) input only
PHASE
Adjusts the visual “noise” on the image.
VGA (RGB) input only
*1: This function is not available when sRGB is selected at PICTURE MODE.
*2: This function is not available in HDMI/DisplayPort MODE when RGB is selected or when AUTO is selected and the input signal is RGB.
*3: This function is not available when 1:1 is selected as ASPECT.
*4: This function is not available for still image by MP input.
English-27
COLOR SYSTEM
The selected Color System depends on the video format of the input signal.
Automatically chooses Color System setting based on input signal.
VIDEO input only
AUTO
NTSC
PAL
SECAM
4.43 NTSC
PAL-60
INPUT RESOLUTION
Selects one of the following pair of resolutions as the input signal priority:
1366 x 768 or 1280 x 768 or 1024 x 768 (vertical resolution 768)
VGA (RGB) input only
ASPECT*1
Select the aspect ratio of the screen image.
NOTE: When the ASPECT is ZOOM, the image will be changed to FULL image before TILE MATRIX, and then
start TILE MATRIX. After TILE MATRIX, the ASPECT will be returned to the previous ASPECT or set ASPECT
during TILE MATRIX.
If you change H POSITION and V POSITION settings with a reduced image, the image would not be changed.
If SCREEN SAVER is set, the ASPECT setting automatically changes to FULL from what you set. Once SCREEN
SAVER is off the ASPECT setting will go back to the setting that you originally set.
This function is not available when MOTION in SCREEN SAVER is active.
When the ASPECT is set to ZOOM while TILE MATRIX is set to active, after releasing TILE MATRIX or ZOOM
will be active.
NORMAL
FULL
Shows the aspect ratio as it is sent from the source.
Fills the entire screen.
WIDE
1:1
Expands a 16:9 letterbox signal to fill the entire screen.
Shows the image in a 1 by 1 Pixel format.
ZOOM
Expands/reduces the image.
NOTE: The areas of the expanded image that are outside of the active screen area are not shown. The reduced
image may have some image degradation.
ZOOM
HZOOM
Maintains the aspect ratio while zooming.
Horizontal zoom value.
Vertical zoom value.
VZOOM
H POS
Horizontal position.
V POS
Vertical position.
ADVANCED
OVER SCAN*2
Some video formats may require different scanning modes in order to best display the image.
HDMI1, HDMI2, HDMI3, DisplayPort,
VGA (YPbPr), VIDEO inputs only
AUTO
ON
Image size is set automatically.
NOTE: This function is not available if input signal is VGA (YPbPr), VIDEO or MP.
Image size is larger than what can be displayed. The image edge will appear cropped.
Approximately 95% of the image will be shown on the screen.
OFF
Image size stays within the display area. The whole image is displayed on the screen.
NOTE: When you use a computer with HDMI out, please set “OFF”.
NOISE REDUCTION
Adjusts the amount of noise reduction. Press + or - to adjust.
VIDEO input only
TELECINE*2
Automatically senses the sources frame rate for optimal picture quality.
HDMI1, HDMI2, HDMI3, DisplayPort,
VIDEO, VGA (YPbPr) inputs only
ADAPTIVE
Sets the level of adjustment for dynamic contrast.
If HIGH is set, the image is displayed clearly but it makes brightness unstable due to the wide gap of contrast
variation.
CONTRAST*2, *3
HDMI1, HDMI2, HDMI3, DisplayPort,
VIDEO, VGA (YPbPr), MP inputs only
RESET
Resets all “PICTURE” settings back to factory settings except for PICTURE MODE.
*1: Except for MP.
*2: This function is not available in HDMI/DisplayPort MODE when RGB is selected or when AUTO is selected and the input signal is RGB.
*3: This function is not available for still image by MP input.
English-28
AUDIO
VOLUME
BALANCE
Increase or decrease output volume level.
BALANCE
Select STEREO or MONO for the audio output.
If you select STEREO, adjust the L/R volume balance.
Press the + button to move the stereo sound image to right.
Press the - button to move the stereo sound image to left.
NOTE: BALANCE is not available if MONO is set at STEREO/MONO.
SURROUND
EQUALIZER
Artificial surround sound.
TREBLE
Accentuate or reduce the high frequency range of audio signals.
Press the + button to increase TREBLE.
Press the - button to decrease TREBLE.
BASS
Accentuate or reduce the low frequency sound.
Press the + button to increase BASS.
Press the - button to decrease BASS.
AUDIO INPUT
Selects the audio input source: [IN1], [IN2], [DisplayPort], [HDMI1], [HDMI2], [HDMI3], [MP].
NOTE: [IN1] and [IN2] are not available if MP is set in INPUT.
LINE OUT
Selecting VARIABLE enables control of the line out level with the VOLUME button.
Selecting OFF enables internal speaker output is turned off.
INTERNAL SPEAKER
AUDIO DELAY
AUDIO DELAY
DELAY TIME
RESET
Activate a delay time to output the audio signal. The DELAY TIME can be set between 0 and 100 milliseconds.
Set to ON to activate this function.
Resets all AUDIO options back to factory settings, except for VOLUME.
SCHEDULE
SCHEDULE SETTINGS
Creates a working schedule for the monitor.
Press the
, + - buttons to navigate and change the schedule settings. Press the SET/ZOOM on the remote
or Input change buttons on the monitor to select settings.
NOTE: Please set DAY & TIME before configuring the SCHEDULE SETTINGS.
When the SCHEDULE SETTINGS window is closed, any schedules that you set are saved.
If schedules are set for the same time, higher SETTINGS numbers are given the priority.
If OFF TIMER is ON, SCHEDULE SETTINGS is not available.
When you select an invalid input signal or picture mode, it will display in red. While the SCHEDULE SETTINGS
window is open, schedules are not operated. Also, see page 36.
SETTINGS
POWER
TIME
Set ON to activate the schedule. Maximum 30 schedules are set.
Setting for the monitor power. Please set ON or OFF for each schedule.
Set the schedule operation time. If there is no specific time for the schedule set [--].
INPUT
Set the input signal for the schedule. To keep the input signal that is active when the schedule starts set [--].
When you set INPUT, please select ON at POWER.
PIC. MODE
Set the picture mode for the schedule. To keep the picture mode that is active when the schedule starts set [--].
When you set PIC. MODE, please select ON at POWER.
Select one item from below (only one item is available).
DATE
Select this setting if the schedule is for one day schedule or irregular schedules.
Select this setting if the schedule is repeating every day.
EVERY DAY
EVERY WEEK
WEEKDAY
Select this setting if the schedule is repeating every week.
Select this setting if the schedule is on a weekday.
This item is set by the WEEKEND and the HOLIDAY settings. A day, which is not selected at WEEKEND and
HOLIDAY setting, is set as a weekday.
WEEKEND
Select this setting if the schedule is on a weekend.
Schedule operates on the date that is set at WEEKEND SETTINGS.
HOLIDAY
Schedule operates on the date that is set at HOLIDAY SETTINGS.
List of working schedules. Displays up to 30 schedules.
SCHEDULE LIST
English-29
HOLIDAY SETTINGS
No.
Creates holiday schedule for the monitor.
YEAR
MONTH
DAY
Set YEAR and MONTH.
Select DAY or WEEK.
DAY: Set a day.
WEEK
WEEK: Set a week and the day of the week.
If you set [--] at MONTH or YEAR, every month or year of the day you set is select as a holiday.
END DAY
Set the end of holiday date. If you schedule beyond a year, please separate the schedule per year.
NOTE: If DAY is not set, END DAY is not available. If your holiday setting includes [--] for year or month,
END DAY is not available.
SET/DELETE
WEEKEND SETTING
WEEKEND
Sets or deletes a schedule.
Set the day of the week.
DATE & TIME
Sets the date, time, and daylight savings region. Date & time must be set in order for the “SCHEDULE” function
NOTE: If the monitor’s main power has been turned off for two weeks, the DATE & TIME setting goes back to the
default setting and the clock function stops working.
YEAR
MONTH
DAY
Sets the year for the real-time clock.
Sets the month for the real-time clock.
Sets the day for the real-time clock.
Sets the time for the real-time clock.
TIME
CURRENT DATE TIME Shows the current date and time.
DAYLIGHT SAVING
Sets daylight savings on or off.
NOTE: Please set the TIME & DATE setting first if you change the DAYLIGHT SAVING setting.
DAYLIGHT SAVING
BEGIN MONTH
END MONTH
If ON is selected, please set daylight savings settings below.
Set daylight savings beginning date.
Set daylight savings ending date.
TIME DIFFERENCE
OFF TIMER
Set the time difference.
Set the monitor to power off after a preset time period. A time period between 1 to 24 hours may be set.
NOTE: SCHEDULE is not available if OFF TIMER is ON.
RESET
Resets the following settings within the SCHEDULE menu back to factory setting: DATE & TIME and DAYLIGHT
SAVING.
MULTI INPUT
INPUT DETECT
NONE
Selects the method of input detection the monitor uses when more than one signal source is connected.
The Monitor will not search for signals at the other video input ports.
FIRST DETECT
When the current video input signal is not present, the monitor searches for a video signal from another video
input port. If a video signal is present in the other input, the monitor switches from the current video source to this
active video source automatically.
The monitor will not look for any other video signals while the current video source is present.
CUSTOM DETECT
Sets the priority of input signals.
When CUSTOM DETECT is selected, the monitor searches on preset inputs only.
When you use digital input (DisplayPort, HDMI1, HDMI2 and HDMI3), other digital input is not detected.
When you use analog input (VGA or VIDEO), other analog input is not detected.
English-30
TERMINAL SETTINGS
VGA MODE
Selects RGB or YPbPr for VGA input.
Select RBR or HBR.
DisplayPort BIT RATE
VIDEO LEVEL
AUTO: Automatically sets input signals by adjusting connected equipment.
RAW: For computer settings. Show all input signals of 0-255 gray levels.
EXPAND: For audio-visual equipment settings. Expands the input signals from 16-235 gray levels to 0-255 gray
levels.
NOTE: This function is available only in HDMI or DisplayPort and is selected at INPUT SIGNAL.
HDMI/DisplayPort
MODE
This function is available in HDMI or DisplayPort input.
AUTO: Automatically switches to RGB or YUV by detecting the internal information of the input signal.
RGB: For RGB in the input signal (e.g. Video output from a connected computer).
YUV: For YUV (YPbPr/YCbCr) in the input signal.
RESET
Resets MULTI INPUT options back to factory settings, except for INPUT DETECT (priority of input signals only)
and DisplayPort BIT RATE.
OSD
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
SVENSKA
РУССКИЙ
Select the language used by the OSD.
OSD TIME
Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.
Selects the location where the OSD appears on the screen.
OSD POSITION
INFORMATION OSD
Selects whether the Information OSD is displayed or not. The Information OSD will appear when the input signal
or input source changes. The Information OSD will also give a warning when no signal is detected or the signal is
out of range.
An interval between 3 to 10 seconds is selectable for the Information OSD to appear.
COMMUNICATION
INFO.
The MONITOR ID and IP ADDRESS will appear when the remote control Display button is pressed.
OSD ROTATION
LANDSCAPE
PORTRAIT
Determines the OSD orientation between landscape and portrait.
Shows the OSD in landscape orientation.
Shows the OSD in portrait orientation.
NOTE: If PORTRAIT is set, CLOSED CAPTION is not available.
KEY GUIDE
MEMO
Key guide is shown when the OSD menu is displayed.
Defines a title and a message via HTTP server. See page 46.
INPUT NAME
You can create a name for the INPUT currently being used.
Max: 14 characters, including Space, A-Z, 0-9, and some symbols.
CLOSED CAPTION
Activates closed captioning.
VIDEO input only
NOTE: This function is released if the following function is activated: PORTRAIT in OSD ROTATION, TILE
MATRIX, SCREEN SAVER, STILL, POINT ZOOM.
RESET
Resets the following settings within the OSD menu back to factory setting:
OSD TIME, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY, CLOSED CAPTION.
English-31
MULTI DISPLAY
TILE MATRIX*1
Allows one image to be expanded and displayed over multiple screens (up to 100) through a distribution
amplifier.
(Except for MP)
NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate without a
distribution amplifier at a lower number of screens.
This function is released when selecting SCREEN SAVER except for NONE.
Zoom will not work when Tile Matrix is activated.
When “ZOOM” is selected in ASPECT while executing TILE MATRIX, the setting will be applied after completing
the TILE MATRIX.
When TILE MATRIX is active the following functions are not available: CLOSED CAPTION, STILL,
If Media Player contents are played while TILE MATRIX is active, the image play timing might have a gap within
monitors.
This function is not available when SCREEN SAVER is active.
H MONITORS
V MONITORS
POSITION
Number of monitors arranged horizontally.
Number of monitors arranged vertically.
Select which section of the tiled image to be displayed on the monitor.
TILE COMP
Turns the TILE COMP feature on. If YES is set to the TILE COMP, you can adjust a displayed image size and
position by pressing the + button or the - button on the remote control.
ENABLE
TILE MATRIX MEM
COMMON
Enables the Tile Matrix settings.
When “INPUT” is selected, the TILE MATRIX setting is applied to each signal input.
All settings in the TILE MATRIX are saved for all signal inputs.
All settings in the TILE MATRIX are saved for the selected signal input.
INPUT
ID CONTROL
Sets the monitor ID number from 1-100 and group ID from A-J.
RESET
Resets all settings within the MULTI DISPLAY menu back to factory setting.
DISPLAY PROTECTION
POWER SAVE
Set ENABLE or DISABLE. If you set it to ENABLE, set how long the monitor waits to go into power save mode
AUTO POWER SAVE
TIME SETTING
Set the time when the monitor goes into auto power save mode after signal is lost.
QUICK TURN ON
When ENABLE is selected, the monitor will quickly return to the ON state when a signal is detected. Enabling this
option increases standby power consumption.
STANDBY USB
POWER
When ENABLE is selected, you can use USB port for power supply in standby mode.
POWER SAVE MESSAGE When the monitor goes into power save mode, a message is displayed when ON is selected.
HEAT STATUS
Shows the actual status of the backlight and temperature sensors.
SCREEN SAVER
Use the SCREEN SAVER function to reduce the risk of Image Persistence.
NOTE: When the screen saver is activated, the image will be changed to FULL image. After the screen saver
stops, the image will be reproduced again with the current ASPECT setting.
When the SCREEN SAVER is set to active, STILL, POINT ZOOM, TILE MATRIX, CLOSED CAPTION are not
available.
BACKLIGHT
MOTION
The brightness of the backlight is decreased when “ON” is selected.
NOTE: Do not select this function when ROOM LIGHT SENSING is set to MODE1 or MODE2.
The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at user determined
intervals. You can set interval time and zoom ratio.
SIDE BORDER COLOR
Adjusts the color of the side borders when a 4:3 image is reproduced.
By pressing the + button on the remote control, the side borders will become brighter.
By pressing the - button, the side borders will become darker.
Background color of the Media Player window is also changed.
POWER ON DELAY
DELAY TIME
Adjusts the delay time between being in “standby” mode and entering “power on” mode.
“POWER ON DELAY” can be set between 0 and 50 seconds.
LINK TO ID
When “ON” is selected, the delay time is linked with the Monitor ID. It takes more time when there are a large
number of IDs.
ALERT MAIL
RESET
Resets all settings within the DISPLAY PROTECTION menu back to factory setting except for POWER ON
DELAY.
*1: Except for MP.
English-32
CONTROL
NETWORK
Shows the current network settings.
INFORMATION
LAN
NOTE: When changing any LAN settings, you need to wait several seconds until modified LAN settings are
applied.
IP SETTING
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to enter a fixed IP address and subnet mask data obtained from your network
administrator.
NOTE: Consult your network administrator for the IP address when AUTO is selected for [IP SETTING].
IP ADDRESS
Set your IP address for the monitor connected to the network when MANUAL is selected for [IP SETTING].
SUBNET MASK
Set your subnet mask data for the monitor connected to the network when MANUAL is selected for
[IP SETTING].
DEFAULT GATEWAY
DNS
Set your default gateway for the monitor connected to the network when MANUAL is selected for [IP SETTING].
NOTE: Enter [0.0.0.0] to delete the setting.
Set the IP addresses of DNS servers.
AUTO: The DNS server, which is connected with the monitor, will automatically assign its IP address.
MANUAL: Manually enter the IP address of the DNS server which is connected with the monitor.
DNS PRIMARY
DNS SECONDARY
CHANGE PASSWORD
Enter the primary DNS server settings of the network connected with the monitor.
NOTE: Enter [0.0.0.0] to delete the setting.
Enter the secondary DNS server settings of the network connected with the monitor.
NOTE: Enter [0.0.0.0] to delete the setting.
Allows the security password to be changed.
The factory preset password is 0000.
SECURITY
PASSWORD
SECURE MODE
OFF
Input a security password.
The security password is not required when the monitor power is on.
START-UP LOCK
CONTROL LOCK
BOTH LOCK
The security password is required when the monitor power is on.
The security password is required when a remote control button or a control button on the monitor is pressed.
The security password is required when either the monitor is powered on, or a remote control button or a control
button on the monitor is pressed.
IR LOCK SETTINGS
Prevents the monitor from being controlled by the wireless remote control.
When ACTIVATE is selected, all settings are activated.
NOTE: IR LOCK SETTINGS is a function intended only for the wireless remote control buttons. This function
does not lock out access to the buttons on the monitor. To return to normal operation, press the “DISPLAY” button
on the remote control and hold it down for more than 5 seconds.
MODE SELECT
UNLOCK
Selects the mode UNLOCK, ALL LOCK or CUSTOM LOCK.
All buttons on the remote control are available for normal operation.
Locks all remote control buttons.
ALL LOCK
CUSTOM LOCK
Selects which buttons to be locked from POWER, VOLUME, and INPUT button.
Except for CUSTOM LOCK settings, other buttons on the remote control are locked.
POWER: When LOCK is selected, the POWER button is locked.
VOLUME: When UNLOCK is selected, set the minimum and maximum volume between VOL.0 to VOL.100.
VOLUME (+) button and VOLUME (-) buttons are only available from the minimum volume to the
maximum volume you set.
When LOCK is selected, VOLUME (+) button and VOLUME (-) buttons are locked.
INPUT:
When UNLOCK is selected, choose up to three buttons from DisplayPort, HDMI1, HDMI2, HDMI3,
VGA (RGB/YPbPr), VIDEO, Media Player which you prefer to be unlocked.
The unselected buttons are locked. When LOCK is selected, all INPUT buttons are locked.
English-33
KEY LOCK SETTINGS
Prevents the monitor from being controlled by the buttons on the monitor.
When ACTIVATE is selected all of the settings are activated.
NOTE: KEY LOCK SETTINGS is a function intended only for the buttons of the monitor. This function does not
lock out access to all buttons on the remote control. To activate the control key lock function, press the power
button for more than 3 seconds. To resume user mode, press the power button for more than 3 seconds.
MODE SELECT
UNLOCK
Selects the mode UNLOCK, ALL LOCK or CUSTOM LOCK.
All buttons are available for normal operations.
Locks all remote control buttons.
ALL LOCK
CUSTOM LOCK
Selects which buttons to be locked from POWER, VOLUME, and INPUT button.
Except for CUSTOM LOCK settings, other buttons on the remote control are locked.
POWER: When LOCK is selected, the POWER button is locked.
VOLUME: When UNLOCK is selected, set the minimum and maximum volume between VOL.0 to VOL.100.
The PLUS button (+) and the MINUS button (-) are only available from the minimum volume to the
maximum volume you set.
When LOCK is selected, the PLUS button (+) and the MINUS button (-) are locked.
INPUT:
When UNLOCK is selected, the INPUT/SET button is unlocked.
CHANNEL: To lock channel buttons on the remote control, select it to LOCK then press ACTIVE,
the UP button ( ) and the DOWN button ( ) are locked.
DDC/CI
ENABLE/DISABLE: Turns ON or OFF the two-way communication and control of the monitor.
VGA (RGB) Input only
PING
Confirm successful connection with the network by communicating with a preset IP address.
Sets an IP ADDRESS for sending PING.
IP ADDRESS
EXECUTE
Checks a reply can be sent to the monitor or not from the IP ADDRESS by sending PING.
Resets IP ADDRESS SETTINGS back to factory settings.
IP ADDRESS RESET
AUTO DIMMING
Adjusts the backlight of the LCD automatically depending on the amount of ambient light.
ROOM LIGHT
SENSING
The backlight of the LCD screen can be set to increase or decrease depending on the amount of ambient light
within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the
monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to
the eye in a variety of lighting conditions.
NOTE: When ROOM LIGHT SENSING is set, BACKLIGHT and BACKLIGHT in SCREEN SAVER functions are
disabled.
Do not cover the room light sensing sensor when you use MODE1 or MODE2.
AMBIENT parameter setting
ROOM LIGHT SENSING in OSD, select MODE1 or MODE2 and set MAX LIMIT, IN BRIGHT and IN DARK in
each mode.
MAX LIMIT: This is the max level of backlight, which you set.
IN BRIGHT: This is the backlight level that the monitor will go up to when the ambient light level is highest.
IN DARK: This is the level of backlight that the monitor will go down to when the ambient light level is low.
When the ROOM LIGHT SENSING is enabled the Backlight level of the screen changes automatically according
to the lighting conditions of the room (see figure below).
Factory Setting
BACKLIGHT range
BACKLIGHT range when
set to MAX LIMIT.
BACKLIGHT level set for
the monitor to use when
ambient lighting level is
low.
BACKLIGHT level set
for the monitor to use
when ambient lighting
level is high.
IN DARK
dark
IN BRIGHT
room bright condition
bright
Screen Backlight value by MODE1
Screen Backlight value by MODE2
MAX LIMIT: BACKLIGHT level is limited to your set level.
IN DARK: BACKLIGHT level set for the monitor to use when ambient lighting level is low.
IN BRIGHT: BACKLIGHT level set for the monitor to use when ambient lighting level is high.
English-34
POWER INDICATOR
POWER INDICATOR
Turns the LED on or off. If OFF is selected, the LED will not glow when the LCD monitor is in active mode.
SCHEDULE
INDICATOR
Turns the LED on or off depending on a schedule activity which is set at “SCHEDULE SETTINGS”. If OFF is
selected, the LED will not glow even if a schedule is in active mode.
CEC*
This function enables you to control the HDMI CEC compliant device connected via HDMI connector.
*: CEC is an abbreviation of Consumer Electronics Control.
CEC
When ON is set, please set items below.
NOTE: If ON is selected, the below functions are activated.
When the connected HDMI CEC device receives a play command, the monitor synchronously turns on then
changes the input signal to HDMI. If the monitor has been turned on, when a connected HDMI CEC device
receives a play command, input signal is switched to HDMI.
The connected HDMI CEC devices are controlled by the wireless remote control supplied with the monitor.
Depending on the connected device, the device may not work properly.
AUTO TURN OFF
AUDIO RECEIVER
When the monitor goes to standby via remote control or the power button on the monitor, a connected HDMI
CEC device go to standby synchronously.
NOTE: If the connected HDMI CEC device is recording, the device does not go into standby.
Activates HDMI CEC audio amplifier. If YES is set, outputs the sounds of the connected HDMI CEC device from
the connected HDMI CEC audio amplifier. If YES is set, the internal speaker is set to mute.
NOTE: When an HDMI CEC audio amplifier is connected, set to YES.
Please set to NO if there is no connected HDMI CEC audio device to the monitor.
SEARCH DEVICE
Searches the HDMI CEC device connected to the monitor. When search is successful, the connected HDMI CEC
device’s type and registered device name are shown. When search has been completed or failed, the SEARCH
DEVICE is set to NO automatically. To retry the SEARCH DEVICE, set it to YES again. After detecting HDMI
CEC devices, you can switch the device input by selecting the device.
RESET
Resets all the settings within the CONTROL menu back to factory setting except for LAN, CHANGE
PASSWORD, SECURITY and PING.
SYSTEM
MONITOR INFORMATION Shows the model name, serial number and firmware version of your monitor.
CARBON SAVINGS: Display the estimated carbon saving information in kg-CO2. The carbon footprint factor in
the carbon saving calculation is based on the OECD (2008 Edition).
CARBON USAGE: Display the estimated carbon usage information in kg-CO2. This is the arithmetic estimation,
not actual measurement value. This estimation is based without any options.
FIRMWARE
Displays firmware version that is installed to the monitor.
Displays the MAC ADDRESS.
MAC ADDRESS
FACTORY RESET
All items are returned to factory shipment state.
NOTE: You can reset all items in all daisy chained monitors. Please be careful to avoid resetting all items
inadvertently.
Default values can be provided on request.
English-35
NOTE 1: CREATING A SCHEDULE
The schedule function allows the monitor to be set to power on or to be on standby at different times. Up to seven different schedules can be
programmed.
To program the schedule:
1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET/POINT ZOOM or the + button
to enter the Settings menu. Highlight the desired schedule number and press SET/POINT ZOOM. The box next to the number will turn yellow.
The schedule can now be programmed.
2. Use the down button to highlight the POWER. Use the + and - buttons to set ON. To set power off schedule, set OFF.
3. Use the down button to highlight the TIME. Use the + and - buttons to set the time.
4. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to highlight
PIC. MODE. Use the + and - buttons to choose the picture mode.
5. Use the down button to select DATE, EVERY DAY, EVERY WEEK, WEEKDAY,
WEEKEND or HOLIDAY. Push the SET/POINT ZOOM button on a menu which is
suitable for the schedule. If the schedule is to be run on a specific day, choose DATE
and press the SET/POINT ZOOM button. If the schedule is to be run every day, choose
EVERY DAY and press the SET/POINT ZOOM button. The circle next to EVERY DAY
will turn yellow. If a weekly schedule is desired, choose the days of the week using the up
and down buttons and pressing SET/POINT ZOOM to select. Then highlight the EVERY
WEEK option and press SET/POINT ZOOM. Please set WEEKDAY, WEEKEND, or
HOLIDAY in the same manner.
HDMI1
MULTI-INPUT
SCHEDULE:
(MON) OCT.26.2015 12:37
SETTINGS:
1
SCHEDULE SETTINGS
SCHEDULE LIST
HOLIDAY SETTINGS
WEEKEND SETTINGS
DATE & TIME
POWER:
TIME:
ON
04 : 03
INPUT:
DVI
DAYLIGHT SAVINGS
OFF TIMER
PIC. MODE:
STANDARD
RESET
DATE
YEAR:
2016
MONTH:
DAY:
JAN
01
The WEEKDAY, WEEKEND, and HOLIDAY settings are available under the SCHEDULE
EVERY DAY
EVERY WEEK
MON
TUE
WED
SAT
THU
SUN
FRI
6. After a schedule is programmed, the remaining schedules can then be set. Press MENU
to leave the OSD or press EXIT to go back to the previous menu.
WEEKDAY
WEEKEND
HOLIDAY
Return
Close
Choose
Mark
NOTE: If schedules are overlapping, the schedule with the highest number will have
priority over the schedule with the lowest number. For example, schedule #7 will have
priority over schedule #1.
If a selected input or picture mode is not available now, the disabled input or picture mode is shown in red.
NOTE 2: IMAGE PERSISTENCE
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a
residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not
permanent, but a still image being displayed for a long period of time should be avoided.
To alleviate image persistence, turn off the monitor’s main power or set it to standby for as long as the previous image was displayed. For
example, if an image was on the monitor for one hour and a residual image remains, the monitor’s main power should be turned off or set it to
standby for one hour to erase the image.
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at
regular intervals whenever the screen is idle, or turn off the monitor’s main power or set it to standby when not in use.
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.
For long life use as a Public Display
Image Sticking of LCD Panel
When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside the LCD and a
residual or “ghost” image of the previous image may be observed. (Image Persistence)
Image Persistence is not permanent, but when a fixed image is displayed for a long period, ionic impurities inside the LCD are accumulated
along the displayed image and may be permanent. (Image Sticking)
Recommendations
To prevent Image Sticking, and for longer life usage of the monitor, the following is recommended.
•
•
A fixed image should not be displayed for long periods.
When not in use, please turn off the monitor via remote control, or use the Power Management function of the PC, or use the built-in Schedule
Functions.
• Lower environmental temperatures prolong the lifespan of the monitor.
When a protective surface (glass, acrylic) is installed over the monitor’s screen surface, the monitor’s screen surface is located in an
enclosure, or if the monitors are stacked, utilize the temperature sensors inside the monitor.
To reduce the internal temperature, use the Screen Saver, the Power Management function of the PC and Low Brightness.
•
Please use “Screen Saver Mode” of monitor.
English-36
Remote Control Functions
REMOTE CONTROL ID FUNCTION
Monitor ID:1
Monitor ID:2
Monitor ID:3
REMOTE CONTROL ID
The remote control can be used to control up to 100 individual monitors using what is called
the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction
with the Monitor ID, allowing control of up to 100 individual monitors. For example, if
there are many monitors being used in the same area, a remote control in normal mode
would send signals to every monitor at the same time (see Figure 1). Using the remote in
REMOTE CONTROL ID mode will only operate one specific monitor within the group (see
Figure 2).
Remote works
Remote works
Remote works
Figure 1
Remote in
Normal mode or
the REMOTE ID
is set to 0
TO SET REMOTE CONTROL ID
While holding down the REMOTE ID SET button on the remote control, use the KEYPAD to
input the Monitor ID (1-100) of the monitor to be controlled via remote. The remote can then
be used to operate the monitor having that specific Monitor ID number.
When 0 is selected or when the remote control is in normal mode, all monitors will be
operated.
Monitor ID:1
Monitor ID:2
Monitor ID:3
TO SET/RESET REMOTE CONTROL MODE
ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for
2 seconds.
Remote does
not work
Remote does
not work
Remote works
Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold
down for 2 seconds.
In order for this feature to work properly, the monitor must be assigned a unique Monitor ID
number. The Monitor ID number can be assigned under the MULTI DISPLAY menu in the
OSD (See page 32).
Figure 2
Remote set up
to use REMOTE
ID:3
Point the remote control towards the remote sensor of the desired monitor and press the
REMOTE ID SET button. The MONITOR ID number is shown on the screen when your
remote control is in ID mode.
Use the remote to control all monitors in range
1. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID
number “0”.
2. All monitors within range of the remote control will now respond to keypad press.
NOTE: When the REMOTE ID is set to “0”, pressing REMOTE ID SET will make all monitors, within range of the remote signal,
display their Monitor ID on screen. This way you can easily see what the monitor ID is if you want to control a single monitor,
as described below.
Use the remote control to operate a monitor that has a specific MONITOR ID number assigned to it
1. Set the MONITOR ID number for the monitor (See page 32). The MONITOR ID number can range from 1-100.
This MONITOR ID number allows the remote control to operate this specific monitor without affecting other monitors.
2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number
(1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the monitor to be controlled.
3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button.
The MONITOR ID number is shown in red on the monitor.
If the REMOTE CONTROL ID is “0”, then all monitors in range will show their respective MONITOR ID number in red.
If the MONITOR ID number is shown in white on the monitor, the MONITOR ID number and the REMOTE CONTROL ID are not the same.
NOTE: The GROUP ID cannot be specified via the remote control.
English-37
WIRED REMOTE CONTROL FUNCTION
You can control multiple monitors by connecting REMOTE IN/OUT with Stereo Mini plug cable (Ø 3.5 mm) [Not supplied].
Remote IN
Remote OUT
Remote IN
Remote OUT
Remote control cable
Remote control cable
NOTE: Turn off the main power switch before connect/disconnect Stereo Mini plug cable.
NOTE: Do not use this connector for any other purpose.
English-38
Controlling the LCD monitor via RS-232C Remote Control
This LCD monitor can be controlled by connecting a personal computer with an RS-232C (reverse type) terminal.
Functions that can be controlled by a personal computer are:
•
•
•
Power ON or standby.
Switching between input signals.
Sound Mute ON or OFF.
Connection
LCD Monitor + computer.
•
•
Please turn off the monitor’s main power when connecting a computer to the monitor.
Please turn on the connecting computer first then turn on the monitor’s main power.
If you turn on the computer and monitor in reverse order, the com port may not work.
•
When controlling the monitor connected with an RS-232C cable, please refer to the Control command diagram (See page 47)
or see the “External_Control.pdf” file on the CD-ROM supplied with the monitor.
Computer
RS-232C
RS-232C Cable
NOTE:
If your computer is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact
your supplier for details.
To control a monitor, please use the control command. Instructions for the control command can be found on the CD included
with the monitor. The file is called “External_control.pdf”.
English-39
1) Interface
PROTOCOL
RS-232C
9600 [bps]
8 [bits]
BAUD RATE
DATA LENGTH
PARITY
NONE
STOP BIT
1 [bit]
FLOW CONTROL NONE
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
The reverse type cable (null modem cable) (not included) should be used for RS-232C control.
2) PIN ASSIGNMENT
RS-232C input/output
Pin No Name
1
2
3
4
5
6
7
8
9
NC
D-Sub 9-pin (Monitor side)
RXD
TXD
NC
5
1
6
GND
NC
9
NC
NC
NC
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
English-40
Controlling the LCD monitor via LAN Control
Connecting to a Network
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function.
To use a LAN connection you are required to assign an IP address.
Example of LAN connection:
Server
NOTE: Use a category 5 or higher LAN cable.
Hub
LAN cable
(not supplied)
Network Setting by Using an HTTP Browser
Overview
Connecting the monitor to a network allows for monitor control from a computer via the network.
The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP
server. Please be sure to use “Microsoft Internet Explorer 10” or a higher version for the web browser.
(This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will
vary depending on the version of the browser. Please refer to the help files and the other information provided in your software.)
Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the
monitor and entering the following URL as described below:
Network Setting
HINT:
The default IP address is assigned automatically to the monitor.
The exclusive application can be downloaded from our website.
NOTE:
If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to
refresh your web browser (or clear the cache).
If the monitor appears to be slow in response to commands or clicks on buttons in the browser, or the general speed
of operation is unacceptable, this may be due to network traffic or the settings on your network. Should this happen,
consult your network administrator.
The monitor may not respond if the buttons shown on the browser are repeatedly pressed in rapid intervals. Should
this happen, wait a moment and repeat. If you still can’t get a response, turn the monitor off and then back on.
English-41
Preparation Before Use
Connect the monitor to the network, using a commercially available LAN cable, before attempting to use browser operations.
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting
method. Although the type of proxy server will be a factor, it is possible that items that have been set will not be shown,
depending on the effectiveness of the cache, and the contents set from the browser may not be reflected in operation.
It is recommended that a proxy server is not used unless the network environment requires it.
Handling of the Address for Operation via a Browser
A host name can be used in the following cases (corresponding to the IP address of the monitor):
The host name must be registered in the domain name server (DNS) by the network administrator. You can then access the
network settings of the monitor via this registered host name by using a compatible browser.
If the host name has been configured in the “HOSTS” file of the computer being used, you can then access the network settings
of the monitor via this host name by using a compatible browser.
Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by
Example 2: When the IP address of the monitor is “192.168.73.1”, access is gained to the mail alert settings by specifying
http://192.168.73.1/index.html for the address or the entry column of the URL.
Operation
Access the following address to show HOME.
Click each link on the left column below HOME.
REMOTE CONTROL
Enable an operation to control the monitor equivalent to the keys on the remote control.
OSD menu
Enable the operation to set the following OSD menu:
INPUT, PICTURE, AUDIO, SCHEDULE, MULTI INPUT, OSD, MULTI DISPLAY, DISPLAY PROTECTION, CONTROL, SYSTEM.
NOTE:
Function of buttons which are shown on setting pages.
[APPLY]: Save your settings.
[CANCEL]: Return to the previous settings. NOTE: CANCEL is disabled after clicking APPLY.
[RELOAD]: Reload the settings.
[RESET]: Resets to the initial setting.
English-42
Network Setting
Click on “NETWORK” on the left column below HOME.
IP SETTING
Select an option for setting the IP ADDRESS.
AUTO: Automatically assign an IP address.
MANUAL: Manually set an IP address for the monitor connected to the network.
NOTE: Consult your network administrator if you have any trouble.
IP ADDRESS
Set your IP address for the monitor connected to the network when [MANUAL] is selected for
[IP SETTING].
SUBNET MASK
Set your subnet mask data for the monitor connected to the network when [MANUAL] is selected for
[IP SETTING].
DEFAULT GATEWAY Set your default gateway for the monitor connected to the network when [MANUAL] is selected for
[IP SETTING].
NOTE: Set as [0.0.0.0] to delete the setting.
DNS
Set for IP ADDRESS setting of DNS server.
AUTO: The DNS server connected to the monitor will automatically assign its IP address.
MANUAL: Manually enter the IP address of the DNS server that is connected with the monitor.
PRIMARY DNS
Enter the primary DNS server settings of the network connected with the monitor.
NOTE: Enter [0.0.0.0] to delete the setting.
SECONDARY DNS
Enter the secondary DNS server settings of the network connected with the monitor.
NOTE: Enter [0.0.0.0] to delete the setting.
NOTE:
The following settings will be set back to the factory settings when IP ADDRESS RESET is selected at CONTROL of
the OSD:
[IP SETTING]: AUTO, [IP ADDRESS]: 192.168.0.10, [SUBNET MASK]: 255.255.255.0, [DNS]: AUTO [DEFAULT
GATEWAY], [PRIMARY DNS] and [SECONDARY DNS] are blank.
English-43
Mail Setting
Click on “MAIL” on the left column below HOME.
This option notifies your computer about an error message via e-mail when using wired LAN. An error message will be sent
when an error occurs in the monitor.
ALERT MAIL
Selecting [ENABLE] will turn on the Alert Mail feature.
Selecting [DISABLE] will turn off the Alert Mail feature.
STATUS MESSAGE
Selecting [ENABLE] will turn on the STATUS MESSAGE feature.
Selecting [DISABLE] will turn off the STATUS MESSAGE feature.
SENDER’S ADDRESS
SMTP SERVER
Type in the sender’s address. Up to 60 alphanumeric and symbols characters can be used.
Type in the SMTP server name to be connected with the monitor.
Up to 60 alphanumeric characters can be used.
RECIPIENT’S
Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.
ADDRESS 1 TO 3
AUTHENTICATION
METHOD
This selects the authentication method of the email transmission.
POP3 SERVER
USER NAME
This specifies the address of the POP3 server that is used in the authentication of the email.
This sets the user name for logging into the authentication server when authentication is required
for the email transmission. Up to 60 alphanumeric characters can be used.
PASSWORD
This sets the password for logging into the authentication server when authentication is required for
the email transmission. Up to 60 alphanumeric characters can be used.
TEST MAIL
Click this button to send a test email to check if your settings are correct.
NOTE:
HINT:
• If you execute a test, you may not receive an Alert email.
Should this happen, check whether the network settings are correct.
• If you entered an incorrect address in a test, you may not receive an Alert email.
Should this happen, check that the Recipient’s Address is correct.
For the control command diagram, please see the file “External_Control.pdf” on the CD-ROM supplied with this
monitor.
Alert error message list
Error number
* ErrorCode
Alert mail Message
Explanation
Measure
The monitor’s power supply is not
functioning normally.
Standby power abnormal
Please contact your supplier.
70h ~ 7Fh
The monitor’s backlight unit is not
functioning normally.
Backlight abnormal
Please contact your supplier.
90h ~ 9Fh
A0h ~ AFh
A2h
The monitor is overheated.
Temperature abnormal
Please contact your supplier.
Please contact your supplier.
A Sensor reached the temperature limit
which was specified in the OSD.
The monitor does not receive an input
signal.
No signal
Please check “No picture” in
“Troubleshooting”.
B0h ~ BFh
The battery for clocks is empty.
The battery is empty.
Please connect the monitor to the
power then recharge the battery.
Please set (DATE & TIME) in OSD.
D1h
E0h ~ EFh
A system error occurred in the monitor. System error.
Please contact your supplier.
English-44
SNMP Settings
Click on “SNMP” on the left column below HOME.
The SNMP protocol is used to get status information and to control a monitor directly via the network.
Version:
SNMP v1 Authenticated plaintext by community name, does not return a confirmation message of the trap.
SNMP v2c Authenticated plaintext by community name, returns a confirmation message of the trap.
Community name:
The default setting of community name is “public”. It is read only. You can set community names for up to 3 settings.
Trap:
Sending error message to a specified address when an error occurs in the monitor.
Check Box
Temperature
Explanation
Temperature abnormal
Power abnormal
Error code
0xA0, 0xA1, 0xA2
0x70, 0x71, 0x72, 0x78
Power
Inverter/Backlight
No Signal
Inverter or backlight abnormal 0x90, 0x91
No signal
0xB0
0xE0
System Error
System error
AMX Settings
Click on “AMX” on the left column below HOME.
AMX BEACON
To turn on or off for the detection from AMX Device Discovery when connecting to a network
supported by an AMX’s NetLinx control system.
HINT:
When using a device that supports AMX Device Discovery, all AMX NetLinx control systems will
recognize the device and download the appropriate Device Discovery Module from an AMX server.
Selecting [ENABLE] AMX Device Discovery will detect the device.
Selecting [DISABLE] AMX Device Discovery will not detect the device.
CRESTRON Settings
Click on “CRESTRON” on the left column below HOME.
CRESTRON ROOMVIEW compatibility
The monitor supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and
controlled from a computer or a controller.
ROOMVIEW
ROOMVIEW for managing from the computer.
ON: Enables ROOMVIEW.
OFF: Disables ROOMVIEW.
CRESTRON
CONTROL
CRESTRON CONTROL for managing from the controller.
ON: Enables CRESTRON CONTROL.
OFF: Disables CRESTRON CONTROL.
CONTROLLER IP
ADDRESS
Sets the IP address of the CRESTRON SERVER.
IP ID
Sets your CRESTRON SERVER IP ID.
HINT:
The CRESTRON settings are required only for use with CRESTRON ROOMVIEW.
English-45
Name Settings
Click on “NAME” on the left column below HOME.
MONITOR NAME
Defines a monitor name. The name must be max. 16 characters long. The default is the model name.
HOST NAME
(CONTROL)
Type in the hostname of the monitor which is connected to the network.
Up to 15 alphanumeric characters can be used.
HOST NAME (MP)
Type in the hostname of the network to be used in the Media Player connected to the monitor.
Up to 15 alphanumeric characters can be used.
DOMAIN NAME
Type in the domain name of the network which is connected with the monitor.
Up to 60 alphanumeric characters can be used.
Network Password Settings
Click on “NETWORK PASSWORD” on the left column below HOME.
PJLink CLASS
Set a class for PJLink*.
NOTE: PJLink is a network interface standard that JBMIA established.
This monitor is available for class1 and class2 command.
NOTIFY FUNCTION Enable or disable a notification of the monitor network condition. This function is only for class2.
ENABLE
NOTIFY ADDRESS
Set an IP ADDRESS to which the monitor network status will be sent. This function is only for class2.
PJLink PASSWORD Set a password for PJLink*. The password must be max. 32 characters long. Do not forget your
password. If you forget your password, consult your supplier.
HTTP PASSWORD
Set a password for the HTTP server. The password must be max. 10 characters long.
HTTP PASSWORD
ENABLE
An HTTP PASSWORD is required when logging into the HTTP server.
Set the monitor name as the USER NAME when entering the password.
*What is PJLink?
PJLink is a standardization of protocol used for controlling devices of different manufacturers. This standard protocol was
established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005.
The device supports all commands of PJLink.
MEMO Settings
Click on “MEMO” on the left column below HOME.
Set a title and message.
TITLE
The title must be max. 24 characters long.
MESSAGE
A message must be max. 240 characters long.
MEMO PASSWORD The default is “0000”.
MEMO PASSWORD A MEMO PASSWORD is required when selecting MEMO PASSWORD ENABLE.
ENABLE
SD-CARD VIEWER setting
Click “SD-CARD VIEWER” on the left side of HOME.
External Control
Connecting external device
There are two ways to connect an external device to the monitor.
• RS-232C terminal.
Connecting an external device to the RS-232C terminal of the monitor with an RS-232C cable.
• LAN port.
Connecting an external device to the LAN port of the monitor with a LAN cable.
For further information regarding the type of LAN cable to use, please consult your network administrator.
English-46
Connecting interface
RS-232C Interface
PROTOCOL
BAUD RATE
DATA LENGTH
PARITY
RS-232C
9600 [bps]
8 [bits]
NONE
STOP BIT
1 [bit]
FLOW CONTROL NONE
LAN interface
PROTOCOL
TCP
PORT NUMBER
7142
COMMUNICATION SPEED AUTO setting (10/100Mbps)
Control command diagram
For other commands, please see “External_Control.pdf” file on the CD-ROM supplied with the monitor.
Function (Monitor ID = 1)
Code Data
Power ON
01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 31 03 73 0d
01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 34 03 76 0d
Power OFF
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 46 03 04 0d
Input Source Select DisplayPort
Input Source Select HDMI1
Input Source Select HDMI2
Input Source Select HDMI3
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 30 46 03 04 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 31 03 72 0d
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 31 31 03 72 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 32 03 71 0d
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 31 32 03 71 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 38 32 03 78 0d
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 38 32 03 78 0d
Input Source Select VGA (RGB)
Input Source Select VGA (YPbPr)
Input Source Select VIDEO
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 31 03 73 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 43 03 01 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 35 03 77 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 38 37 03 7D 0d
Input Source Select MP
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 38 37 03 7D 0d
Sound Mute ON
Sound Mute OFF
01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 31 03 09 0d
01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 32 03 0a 0d
ASCII Control command
This monitor supports control command, which is listed in the “External_Control.pdf” file on the CD-ROM supplied with the
monitor, but also supports common ASCII control command, which is used for controlling the NEC monitor or projector from a
connected PC. For further information please visit our website.
Parameter
Input command
Status command
Input signal name
DisplayPort
HDMI1
Response
DisplayPort
hdmi1
Parameter
Response
error:temp
error:light
Error status
DisplayPort or DisplayPort1
hdmi1 or hdmi
hdmi2
Temperature abnormal
Inverter or backlight abnormal
System error
HDMI2
hdmi2
error:system
HDMI3
hdmi3
hdmi3
VGA
vga
vga, vga1, computer,
computer1, rgb or rgb1
VIDEO
MP
video
mp
video or video1
mp
English-47
Supporting HDMI CEC command
HDMI CEC command name
Explanation
OSD menu
Setting
CEC
One Touch Play
If HDMI CEC supporting devices are
turned on, the monitor connected to the
devices by HDMI cable is also turned on
automatically. After that, the input switches
to HDMI from an input, which you selected.
If the monitor is turned on when HDMI
CEC devices are turned on, it changes the
input from the original one to HDMI.
(Consumer
Electronics
Control)
To set CEC menus please follow the
steps below.
Remote Control Pass
Through
The monitor’s wireless remote control
button operation is functioning to HDMI
CEC supporting devices.
For example, if turning on the monitor by
wireless remote control and pressing the
play button, HDMI CEC supporting devices
will also be turned on and play.
By using
buttons select
CONTROL > CEC then press
SET/POINT ZOOM button on the CEC.
By using + - buttons select ON then
press SET/POINT ZOOM button on
the ON.
Power Status
Connected HDMI CEC supporting devices
obtains the monitor’s power status, such as
the monitor is in standby mode or on.
System Information
This function obtains the information of a
connected HDMI CEC supported device
(CEC version, Physical Address). In
addition, this function copes with “Change
Language function”.
If the language for the monitor is changed,
the language for a connected HDMI CEC
supported device is changed to the same
language, which is selected for the monitor.
For the “Change Language function”, it is
necessary that the connected HDMI CEC
supported device be able to cope with
multi-language.
AUTO
TURN OFF
System Standby
If the monitor is set to standby using the
wireless remote control supplied with the
monitor, HDMI CEC supported devices
also go into standby at the same time.
If the monitor goes into standby while an
HDMI CEC supported device is recording,
the device is kept on. Please refer to the
user’s manual supplied with the HDMI CEC
supported device for further information.
By using
AUTO TURN OFF then press
SET/POINT ZOOM.
buttons select
By using + - buttons select YES
then press SET/POINT ZOOM button
on the YES.
AUDIO
RECEIVER
System Audio Control
The function sends digital audio signal
through the HDMI cable. Please set an
HDMI CEC audio amplifier between the
monitor and an HDMI CEC supported
device with an HDMI cable.
The Volume button on the wireless
remote control supplied with the monitor
is also controlling the volume of the
connected HDMI CEC audio amplifier.
While this function is active, the internal
speaker is set to MUTE automatically.
By using
AUDIO RECIEVER then press
SET/POINT ZOOM.
buttons select
By using + - buttons select YES
then press SET/POINT ZOOM button on
the YES.
SEARCH
DEVICE
Device OSD Name Transfer This function obtains the connected HDMI
CEC supported device’s name.
By using
buttons select SEARCH
DEVICE then press SET/POINT ZOOM.
Routing Control
By selecting a device name, the HDMI
CEC supported device input switches to
the input you selected. After selecting the
device, wireless remote control operation is
functioning for the selected device.
By using + - buttons select YES then
press SET/POINT ZOOM button on
the YES.
This CEC function supports Feature Abort. We recommend that connecting this monitor to a device supporting HDMI CEC.
English-48
POINT ZOOM
Using the “SET/POINT ZOOM” button on the remote control enlarges part of the screen image.
Press the CH+/- button to zoom in or out. The image can be expanded up to 10 times.
1
2
3
4
5
6
Press the [SET/POINT ZOOM] button on the remote control. The icon looks like a magnifier.
Move the magnifier icon with the [ ] [ ] [+] [-] buttons.
Press the [CH+] to zoom in. Press [CH-] to zoom out.
Press the [SET/POINT ZOOM] to let the icon disappear.
Press the [EXIT] to return to the normal image size.
Press the [MENU] to open the OSD menu.
NOTE:
• When using this function the image may look distorted.
• This function is not available when set to SCREEN SAVER, CLOSED CAPTION and TILE MATRIX.
• When ZOOM is selected in ASPECT, the image will change to FULL. Then start with POINT ZOOM.
After exiting POINT ZOOM, ASPECT will return to the previous ASPECT settings. When ASPECT is changed
during the POINT ZOOM operation, ZOOM will be set to FULL image.
• The magnifier icon does not move to a no image area.
• POINT ZOOM returns to the normal image size after changing the input signal or when the monitor is powered off.
• POINT ZOOM will become inactive when changing the ASPECT setting during the POINT ZOOM operation.
• When the POINT ZOOM is active, the STILL function is not available.
English-49
Features
Natural Color Matrix: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments
via six axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard
provides the monitor with a uniform color profile. This ensures that the colors displayed on the monitor are exactly the same as
on the color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your
screen and customise the color accuracy of your monitor to a variety of standards.
sRGB Color Control: A color management standard which allows for color matching on computer monitors and other
peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation and
backward compatibility with other common color standards.
OSD (On-Screen-Display) Controls: Provides access for quick and easy adjustment to all elements of the screen image via
simple to use on-screen menus.
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing the
monitor to send its capabilities (such as screen size and resolutions supported) directly to the computer, automatically optimizing
display performance.
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a lower-
power mode when on but not in use, reducing emissions and lowering the cost of operating the monitor by reducing its power
consumption.
FullScan Capability: Allows use of the entire screen area in most resolutions, significantly expanding the image size.
VESA Standard (FDMIv1) Mounting Interface: Mounts the monitor to any VESA standard (FDMIv1) third party mounting arm
or bracket. NEC recommends using mounting equipment which complies with TÜV-GS (Germany) and/or UL1678 standard
(North America).
ZOOM: Expands/reduces the image size in horizontal and vertical direction.
Self-diagnosis: If an internal error should occur, a failure state will be indicated.
HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent over
a digital signal. If you are unable to view material via the digital input, this does not necessarily mean that the monitor is not
functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected by HDCP and
might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).
TILE MATRIX,TILE COMP: Shows one image over multiple screens with accuracy while compensating for bezel width.
English-50
Troubleshooting
The image is unstable, unfocused or swimming is
apparent
No picture
•
The signal cable should be completely connected to the
•
The signal cable should be completely attached to the
display card/computer.
computer.
•
•
The display card should be completely seated in its slot.
•
Use the OSD Image Adjust controls to focus and
adjust the display by increasing or decreasing the fine
adjustment.
When the display mode is changed, the OSD Image
Adjust settings may need to be re-adjusted.
Check the main Power Switch, it should be in the ON
position.
•
•
Power Switches for the monitor and computer should be
in the ON position.
Make sure that a supported resolution has been selected
on the display card or system being used. If in doubt,
please refer to the user’s manual of the display card or
system to change the resolution.
•
•
•
Check the monitor and your display card with respect to
compatibility and recommended signal timings.
If text looks garbled, change the video mode to non-
interlaced and use a 60 Hz refresh rate.
•
•
•
Check the monitor and your display card with respect to
compatibility and recommended signal timings.
The image may be distorted when turning the power on or
changing the settings.
Check the signal cable connector for bent or pushed-in
pins.
The image of component signal is greenish
•
Check to see if the VGA (YPbPr) input connector is
selected.
The monitor automatically goes into standby at the preset
time period after the video signal was lost. Press the
power on button on the remote control or press the power
button on the monitor.
LED on the monitor is not lit (no blue or red color can be
seen)
•
If you unplug the signal cable when starting the computer,
images may not be displayed. Turn off the monitor and
the computer and then connect the signal cable and turn
on the computer and the monitor.
•
•
•
The main Power Switch should be in the ON position and
the power cord should be connected.
Make certain the computer is not in a power-saving mode
(touch the keyboard or move the mouse).
Power Button does not respond
•
Check in the OSD that the power indicator option is set to
ON.
Unplug the power cord of the monitor from the AC outlet
to turn off and reset the monitor.
LED colors, except for blue, are blinking or glowing
•
Check the main Power Switch on the monitor.
•
A certain failure might have occurred, please contact your
supplier.
Image persistence
•
Please be aware that LCD Technology may experience
a phenomenon known as Image Persistence. Image
Persistence occurs when a residual or “ghost” image of
a previous image remains visible on the screen. Unlike
CRT monitors, the image persistence of LCD monitors is
not permanent, but single still image being displayed for a
long period of time should be avoided. To alleviate image
persistence, put the monitor into standby via remote
control or turn the monitor’s main power off for as long
as the previous image was displayed. For example, if an
image was on the monitor for one hour and a residual
image remains, the monitor should be in standby or main
power off for one hour to erase the image.
•
If the monitor is powered off by the internal temperature
being higher than the normal operating temperature,
the LED will blink green or amber or red for six times.
Power on the monitor again after confirming the internal
temperature has been reduced to normal operation
temperature.
•
The monitor could be in standby.
Press the power on button on the remote control or press
the power button on the monitor.
The image is not properly reproduced
•
Use the OSD Image Adjust controls to increase or
decrease the coarse adjustment.
•
Make sure that a supported resolution has been selected
on the display card or system being used.
If in doubt, please refer to the user’s manual of the display
card or system to change the resolution.
NOTE:
As with all personal display devices, NEC
DISPLAY SOLUTIONS recommends displaying
moving images, using a moving screen saver, or
changing still images at regular intervals whenever
the screen is idle, or turning it into standby or main
power off of the monitor when not in use.
Selected resolution is not displayed properly
•
Use OSD Display Mode to enter Information menu and
confirm that the appropriate resolution has been selected.
The image is blinking
•
If you use a signal repeater or distributor or a long
cable, this may cause image roughness or blink for a
moment. In this case please connect the cable to the
monitor directly without using a repeater or a distributor,
or replace the cable with a higher quality cable. Using
a twisted pair extender may cause image roughness
depending on the environment where the monitor is in or
the cable you are using. For further information please
ask your supplier.
English-51
No Sound
Interference in TV
•
Check to see if the audio cable is properly connected.
•
Check components for shielding, move away from
monitor if necessary.
•
Check to see if MUTE is activated. Use the remote control
to enable or disable the Mute function.
RS-232C or LAN control is not available
•
•
Check to see if VOLUME is set to a minimum.
•
Check RS-232C (reverse type) or the LAN cable.
A category 5 or higher LAN cable is required for
connection.
Check to see if the computer supports an audio signal
through DisplayPort.
If unsure, contact your supplier.
The monitor goes into standby automatically
•
•
When LINE OUT is not functioning, check to see if
SURROUND is ON.
•
Please check “OFF TIMER” setting.
•
Set the “CEC” function to OFF.
If HDMI CEC audio device is not connected, please set
“AUDIO RECEIVER” to OFF.
Media Player function does not recognize the USB
storage device
•
The Remote Control is not functioning
Please check a USB storage device is connected to the
USB (2A).
•
•
•
Check the batteries status of the Remote Control.
Check if the batteries are inserted correctly.
The USB Hub does not operate
•
Check if the Remote Control is pointing at the remote
control sensor of the monitor.
Check to make sure the USB cord is properly connected.
Refer to your USB device User’s Manual.
•
•
Check the status of IR LOCK SETTINGS.
•
Check the format if this device cannot recognize the
connected USB memory.
The remote control system may not function when direct
sunlight or strong illumination strikes the remote control
sensor of the monitor, or when there is an object in the
path.
MicroSD card does not work
•
Check to make sure the microSD card is properly
connected.
The SCHEDULE/OFF TIMER function is not working
properly
•
Check the microSD memory card format.
•
The “SCHEDULE” function will be disabled when the
“OFF TIMER” is set.
•
If the “OFF TIMER” function is enabled and the power to
the LCD monitor is turned off when the power supply is
interrupted unexpectedly, then the “OFF TIMER” will be
reset.
Either light vertical or horizontal stripes may appear, depending on the specific image pattern. This is not a product fault or degradation.
English-52
Specifications - C431
Product Specifications
LCD Module
43"/107.95 cm diagonal
Pixel Pitch: 0.49 mm
Resolution: 1920 x 1080
Color: Over 1073 million colors (depending on display card used)
Brightness: 400 cd/m2 (Max.) @25°C
Contrast Ratio: 4000:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz
Vertical: 50.0 - 85.0 Hz (Analog Input)
24.0 - 85.0 Hz (Digital Input)
Pixel Clock
Analog: 13.5 MHz, 25.0 MHz - 165.0 MHz
Digital: 25.0 MHz - 165.0 MHz
Viewable Size
940.90 x 529.25 mm
Input Signal
DisplayPort DisplayPort Connector Digital RGB
DisplayPort V1.1a (HDCP1.3)
SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60*1, 1920x1080 (60 Hz), 1080p,
1080i, 720p@50Hz/60Hz
VGA
Mini D-Sub 15-pin
Analog RGB
Sync
0.7 Vp-p/75 ohm
(RGB)*2
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI
HDMI Connector
Mini D-Sub 15-pin
RCA port
Digital YUV
Digital RGB
HDMI (HDCP1.4)
SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60*1, 1920x1080 (60 Hz), 1080p,
1080i, 720p@50Hz/60Hz
VGA
Component
Composite
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz,
480i@60Hz
(YPbPr)*2
VIDEO*2
1.0 Vp-p/75 ohm
NTSC/PAL/SECAM/4.43NTSC/PAL60
AUDIO
AUDIO
Input
Stereo Mini Jack
HDMI Connector
Analog Audio
Digital Audio
Stereo L/R 0.5 Vrms x 2
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
Stereo Mini Jack Analog Audio
AUDIO
Output
Speaker Output
Control
Internal Speaker 10 W + 10 W (Stereo)
RS-232C In: D-Sub 9-pin
LAN: RJ-45 10 BASE-T/100 BASE-TX x1
Remote IN: Stereo Mini Jack 3.5 mm Ø
Remote OUT: Stereo Mini Jack 3.5 mm Ø
SD card Slot
USB Port
Port: microSD card. Up to 32GB microSDHC is supported.
USB (2A): Media Player/Firmware update/Power supply port 5V/2A (max.)
1.35 - 0.55 A @ 100-240V AC, 50/60Hz
Power Supply
Power Consumption
Normal operation: Approx. 50 W
Operational Environment
Temperature: 0 - 40°C / 32 - 104°F
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Storage Environment
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension*3
970.7 (W) x 558.9 (H) x 45.0 (D) mm/38.2 (W) x 22.0 (H) x 1.8 (D) inches
Weight
12.5 kg (27.6 lbs)
VESA compatible mounting interface
Power Management
300 mm x 300 mm (M6, 4 Holes)
VESA DPM
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: Common terminal.
*3: Measurements are of the monitor only and do not include removable parts that protrude.
English-53
Specifications - C501
Product Specifications
LCD Module
50"/125.73 cm diagonal
Pixel Pitch: 0.57 mm
Resolution: 1920 x 1080
Color: Over 1073 million colors (depending on display card used)
Brightness: 400 cd/m2 (Max.) @25°C
Contrast Ratio: 4000:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz
Vertical: 50.0 - 85.0 Hz (Analog Input)
24.0 - 85.0 Hz (Digital Input)
Pixel Clock
Analog: 13.5 MHz, 25.0 MHz - 165.0 MHz
Digital: 25.0 MHz - 165.0 MHz
Viewable Size
1095.84 x 616.41 mm
Input Signal
DisplayPort DisplayPort Connector Digital RGB
DisplayPort V1.1a (HDCP1.3)
SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60*1, 1920x1080 (60 Hz), 1080p,
1080i, 720p@50Hz/60Hz
VGA
Mini D-Sub 15-pin
Analog RGB
Sync
0.7 Vp-p/75 ohm
(RGB)*2
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI
HDMI Connector
Mini D-Sub 15-pin
RCA port
Digital YUV
Digital RGB
HDMI (HDCP1.4)
SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60*1, 1920x1080 (60 Hz), 1080p,
1080i, 720p@50Hz/60Hz
VGA
Component
Composite
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz,
480i@60Hz
(YPbPr)*2
VIDEO*2
1.0 Vp-p/75 ohm
NTSC/PAL/SECAM/4.43NTSC/PAL60
AUDIO
AUDIO
Input
Stereo Mini Jack
HDMI Connector
Analog Audio
Digital Audio
Stereo L/R 0.5 Vrms x 2
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
Stereo Mini Jack Analog Audio
AUDIO
Output
Speaker Output
Control
Internal Speaker 10 W + 10 W (Stereo)
RS-232C In: D-Sub 9-pin
LAN: RJ-45 10 BASE-T/100 BASE-TX x1
Remote IN: Stereo Mini Jack 3.5 mm Ø
Remote OUT: Stereo Mini Jack 3.5 mm Ø
SD card Slot
USB Port
Port: microSD card. Up to 32GB microSDHC is supported.
USB (2A): Media Player/Firmware update/Power supply port 5V/2A (max.)
1.50 - 0.60 A @ 100-240V AC, 50/60Hz
Power Supply
Power Consumption
Normal operation: Approx. 65 W
Operational Environment
Temperature: 0 - 40°C / 32 - 104°F
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Storage Environment
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension*3
1124.7 (W) x 645.3 (H) x 45.0 (D) mm/44.3 (W) x 25.4 (H) x 1.8 (D) inches
Weight
16.1 kg (35.5 lbs)
VESA compatible mounting interface
Power Management
300 mm x 300 mm (M6, 4 Holes)
VESA DPM
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: Common terminal.
*3: Measurements are of the monitor only and do not include removable parts that protrude.
English-54
Specifications - C551
Product Specifications
LCD Module
55"/138.78 cm diagonal
Pixel Pitch: 0.63 mm
Resolution: 1920 x 1080
Color: Over 1073 million colors (depending on display card used)
Brightness: 400 cd/m2 (Max.) @25°C
Contrast Ratio: 4000:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz
Vertical: 50.0 - 85.0 Hz (Analog Input)
24.0 - 85.0 Hz (Digital Input)
Pixel Clock
Analog: 13.5 MHz, 25.0 MHz - 165.0 MHz
Digital: 25.0 MHz - 165.0 MHz
Viewable Size
1209.6 x 680.40 mm
Input Signal
DisplayPort DisplayPort Connector Digital RGB
DisplayPort V1.1a (HDCP1.3)
SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60*1, 1920x1080 (60 Hz), 1080p,
1080i, 720p@50Hz/60Hz
VGA
Mini D-Sub 15-pin
Analog RGB
Sync
0.7 Vp-p/75 ohm
(RGB)*2
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI
HDMI Connector
Mini D-Sub 15-pin
RCA port
Digital YUV
Digital RGB
HDMI (HDCP1.4)
SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60*1, 1920x1080 (60 Hz), 1080p,
1080i, 720p@50Hz/60Hz
VGA
Component
Composite
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz,
480i@60Hz
(YPbPr)*2
VIDEO*2
1.0 Vp-p/75 ohm
NTSC/PAL/SECAM/4.43NTSC/PAL60
AUDIO
AUDIO
Input
Stereo Mini Jack
HDMI Connector
Analog Audio
Digital Audio
Stereo L/R 0.5 Vrms x 2
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
Stereo Mini Jack Analog Audio
AUDIO
Output
Speaker Output
Control
Internal Speaker 10 W + 10 W (Stereo)
RS-232C In: D-Sub 9-pin
LAN: RJ-45 10 BASE-T/100 BASE-TX x1
Remote IN: Stereo Mini Jack 3.5 mm Ø
Remote OUT: Stereo Mini Jack 3.5 mm Ø
SD card Slot
USB Port
Port: microSD card. Up to 32GB microSDHC is supported.
USB (2A): Media Player/Firmware update/Power supply port 5V/2A (max.)
1.55 - 0.65 A @ 100-240V AC, 50/60Hz
Power Supply
Power Consumption
Normal operation: Approx. 75 W
Operational Environment
Temperature: 0 - 40°C / 32 - 104°F
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Storage Environment
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension*3
1238.4 (W) x 709.2 (H) x 45.0 (D) mm/48.8 (W) x 27.9 (H) x 1.8 (D) inches
Weight
18.8 kg (41.4 lbs)
VESA compatible mounting interface
Power Management
300 mm x 300 mm (M6, 4 Holes)
VESA DPM
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: Common terminal.
*3: Measurements are of the monitor only and do not include removable parts that protrude.
English-55
Manufacturer’s Recycling and Energy Information
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top
priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly
products, and always strive to help define and comply with the latest independent standards from agencies such as ISO
(International Organisation for Standardization) and TCO (Swedish Trades Union).
Disposing of your old NEC product
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures
and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.
All required information concerning the disposal of the product and country-specific information on recycling facilities can be
found on our following websites:
https://www.nec-display.com (in Japan) or
http://www.necdisplay.com (in USA).
Energy Saving
This monitor features an advanced energy saving capability. When a Display Power Management signal is sent to the monitor,
the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.
For additional information visit:
http://www.necdisplay.com/ (in USA)
http://www.nec-display-solutions.com/ (in Europe)
For ErP requirement/For ErP (Network standby) requirement:
Condition: INPUT DETECT is not NONE, STANDBY USB POWER is ENABLE, or QUICK TURN ON is ENABLE.
Power consumption: 2 W or less (Glowing amber).
Time for power management function: 40 sec. (Default setting)
(Except for a condition that the monitor has plural signal inputs.)
Power consumption: 0.5 W or less (Blinking amber).
Time for power management function: 3 min. (Default setting)
(Except for a condition that the monitor has plural signal inputs.)
WEEE Mark (European Directive 2012/19/EU and amendments)
Disposing of your used product: In the European Union
EU-wide legislation as implemented in each Member State requires that used electrical and electronic products
carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors
and electrical accessories, such as signal cables or power cords. When you dispose of such products, please
follow the guidance of your local a uthority or ask the shop where you purchased the product, or if applicable,
follow applicable legislation or agreement you may have. The mark on electrical and electronic products may
only apply to the current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority
and ask for the correct method of disposal.
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household
waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in
accordance with legislation.
According to EU directive 2006/66/EC, the battery can’t be disposed improperly.The battery shall be separated to
collect by local service.
English-56
[Notice] About the MPEG-4 AVC,
MPEG-4 Visual license included in this product
1. MPEG-4 AVC
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF
A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN
COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY
A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED
TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM
2. MPEG-4 Visual
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL
STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR
ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND
COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM.
English-57
|