2000W FITNESS WHOLE BODY VIBRATION PLATE
EXERCISE MACHINE
ITEM: 96421
OWNER’S MANUAL AND SAFETY INSTRUCTIONS
SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE
PRODUCT’S SERIAL NUMBER ON THE BACK OF THE MANUAL NEAR THE ASSEMBLY DIAGRAM
(OR MONTH AND YEAR OF PURCHASE IF PRODUCT HAS NO NUMBER).
FOR QUESTIONS PLEASE CALL OUR CUSTOMER SUPPORT: (909) 628 0880 MON-FRI 9AM TO 3PM PST
IMPORTANT SAFETY INFORMATION
Hold the safety handle correctly before you begin exercise to help you keep balance.
Check the exercise speed level before you operate the machine to ensure it is at a
comfortable and safe speed.
Ensure that there is sufficient gad between your feet. Recommended gap should be around
30cm.
Do not use this machine for anything other than intended purposes.
Do not operate or touch the machine with wet hands. Doing so may cause electric shock and/
or damage to the machine.
Always unplug the machine when not in use.
WARNINGS AND DISCLAIMERS
XtremePowerUS claims no liability for any damage or injury that result from the use of
the machine by persons who have not read and understood the cautions contained in
this manual, or through any misuse of the unit. You are responsible for your safety while
operating this machine.
To receive maximum performance and satisfaction from the machine, it is important that
you read and understand the safety precautions before using the machine.
IMPORTANT: The manufacturer does not accept responsibility for damages caused to or
by the trimmer resulting from an inadequate use or assembly.
2
DIAGRAMS
3
PARTS LIST
4
INSTALLATION
STEP 1: Adjust the height of the machine foot to keep
the machine balanced.
STEP 2: Connect three connectors between the
support tube and the controller, then place the
support tube toward the rear of the machine vertically.
Then tighten the tube with 4 of the M8x12 screws.
STEP 3: Place the two lower safety handles to the
machine body and tighten them with 4 of the M6 x
12 screws.
STEP 4: Connect the two upper safety handles
then tighten them with 4 of the M5 x 12 screws.
Then tighten the two upper safety handles to the
top support tube with two of the M8 x 50 screws.
STEP 4: Connect three connectors between
the console and the support tube, then tighten
the console with three of the M6 x 12 screws.
NOTE: Wires should not be pressed by console
after assembly.
5
FEATURES
Choose from three pre-set programs, each stimulates different terrain profiles
and varied levels:
P1: Cardiovascular Exercise
P2: Detoxifying Program
P3: Body Perfection Program
Variants of Speed Range
Reduce unwanted body fat effectively with variants of speed range and strong
massage vibration.
Ergonomic Construction with Streamlined Design
Unique ergonomic design with a streamlined form.
User Friendly Console with Window Display Screens
The user friendly console features LCD screens that you can manually customize
your workout routine. Also shows your desired workout time and level of speed.
Durable Steel Frame
The durable steel frame features a tough and sporty design.
Current Overload Protection
Static Electricity Resistance
EFFECTIVENESS AND TRAINING GUIDE
1. Improves blood circulation
2. Intestinal improvement
3. Thigh firming
4. Rear firming function
5. Waist and Abdomen shaping function
6. Shoulder shaping function
6
INSTRUCTIONS FOR USE
1. Insert the power plug into the power socket of the machine. Check the voltage
and switch on the power switch.
2. Choose your desired posture while on the machine (examples above)
3. Press the start button to begin the program.
4. Set your stats by pressing the program button sequentially. Hold the BMI sensor
on handles to get your BMI readout.
POWER SWITCH: Secure the electrical cord to
the power connector. Turn on main power with
this switch.
7
SUGGESTIONS AND INFORMATION
8
PRECAUTIONS AND MAINTENANCE
Do not store this machine near heat or an open flame, under direct sunlight or
in especially humid areas.
Keep the machine’s:
Usage temperature: 0-35°C
Keeping temperature: 5-50°C
Humidity: Under 40-80%
If the machine is not in use for an extended period of time, cover it to protect from
dust.
Do not store the machine under direct sunlight or in high temperatures.
Do not coil the power cord as it may cause the machine to malfunction.
Do not use the machine in wet areas such as a bathroom, spa or pool.
Using a corrosive cleaner is prohibited. Do not use benzene or thinner to clean the
machine.
Maintenance
Before cleaning, ensure the main switch is turned off and the AC plug is removed
from the electrical outlet.
Do not use the machine for an extended period of time the first time. Get used to the
machine first. Increase over time.
Switch off the power and remove the plug from the socket every time after use.
9
EXERCISE SUGGESTIONS
STRAIGHT STANDING
POSE
WALKING STYLE
LEFT LEG IN FRONT
HORSE RIDING POSE
STAND-A-SIDE POSE
WALKING STYLE
RIGHT LEG IN FRONT
STRAIGHT STANDING
POSE
10
EXERCISE SUGGESTIONS
LOTUS POSE
PUSH UP POSE
BOW AND ARROW
STEP POSE
BENT LEG POSE
SITTING POSE
11
SPECIFICATIONS
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIEDAND LICENSED TECHNICIANS,AND NOT BYTHE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
12
|