CREALITY HALOT ONE User Manual

Create Realities, Realize Dreams  
HALOT-ONE  
HALOT-ONE  
3D Printer User Manual  
V1.0  
Instructions for Use  
Do not use this printer by methods or operations that are not described in this manual, otherwise it may result in accidental injury or property damage.  
1
2
3
4
5
6
7
8
Do not place this printer near flammable materials, explosive materials or high heat sources. Please place this printer in a ventilated, cool and low-dust environment.  
Do not place this printer in a vibrating or any other unstable environment, as the printing quality will be compromised when the printer shakes.  
Please use the filament recommended by the manufacturer, otherwise the printer may be damaged.  
Please use the power cord provided with the printer and do not use the power cord of other products. The power plug must be plugged into a three-hole socket with a ground wire.  
Do not open the printer cover while the printer is in operation, otherwise the printing process may be interrupted.  
Do not wear cotton gloves while operating the printer, otherwise the moving parts may cause accidental injury including cuts and lacerations.  
After the printing is complete, please wear gloves and wait for a while before removing the printing platform. Use tools to remove the model from the platform, and do not touch  
the platform with your bare hands when cleaning it.  
9
Please regularly clean the printer body with a dry cloth while the power is off, and wipe off dust, sticky printing materials, and foreign objects on the guide rails.  
10  
Children under the age of 10 must not use this printer without adult supervision in order to avoid accidental injury.  
11  
Warning: Do not plug or unplug the power cable while the printer is turned on.  
12  
Users should abide by the laws and regulations of the corresponding country and region where the equipment is located (place of use), abide by professional ethics, and pay  
attention to safety obligations. The use of our products or equipment for any illegal purpose is strictly prohibited. Our company is not responsible for the relevant legal  
responsibilities of any violators.  
Table of Contents  
About the Printer  
01-01  
Device Specifications  
02-02  
03-03  
List of Parts  
Installing the 3D Printer  
Using the 3D Printer  
First Printing  
04-05  
06-10  
11-13  
14-14  
15-15  
16-16  
Remote Controlled Printing  
Circuit Wiring  
Troubleshooting  
1. About the Printer  
7
8
9
11  
12  
10  
USB Port  
Torx Head Screw  
Leveling Screw  
Tray  
Touch Screen  
Type-B USB Port  
Platform  
Limit Sensor  
Air Filter  
Power Switch  
Power Socket  
Tray Fixing Screw  
01  
2.Equipment parameters  
Basic Parameters  
Model Name  
HALOT-ONE  
Build Size  
127*80*160mm(length,width and height)  
XY Axis Resolution  
XY Axis Accuracy  
Print speed  
1620*2560  
0.05mm  
1-4S/layer  
0.01-0.2mm  
Layer Thickness  
Touch Screen  
Light Source Type  
Rated Voltage  
Rated Power  
5 inch touch screen  
Integral light source (wavelength 405nm)  
100-240V~, 50/60Hz  
100W  
Machine Size  
Package size  
Net Weight  
221*221*404mm  
295*295*545mm  
7.1KG  
Gross Weight  
8.8KG  
Print Method  
USB Disk, Creality Cloud  
Machine Language  
中文(简 /繁)/ English/ Español/ Deutsche/ Français/ Pусский/ Português/ Italiano/ Türk/Nederlands/Polskie/日本語/한국어  
Win7/Win8/Win10 64bit, Mac system(32-bit is not supported)  
Slicing Software Operation System  
Compatible Resin  
Common rigid photosensivie resin, Standard resin, Hight hardness,High toughness, Dental model resin.  
02  
3. List of Parts  
Printing Platform x 1  
Printer x 1  
Tray x 1  
List of Tool Kit Items  
USB Drive x 1  
2#, 2.5#, 3# Screwdriver x 1  
Paint Brush x 1  
Power Cord x 1  
Paper Funnel x 4  
Release Filmx 1  
Metal Blade x 1  
Note: The components above are for reference only. The actual product may vary.  
03  
4. Assemble the 3D Printer  
Remove the protective cotton above the printing screen  
as shown in the picture:  
2.Remove the resin vat  
1. Take out the machine  
3.Remove the foam above the screen  
04  
5. Installing the 3D Printer  
Printer x 1  
Note: Embed the upper cover in the mainframe to complete the installation.  
Upper Cover x 1  
05  
6. Interface Information  
Setting  
Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official  
website of the latest firmware Ul as the standard.  
06  
7. Leveling the Platform 1  
1. To calibrate the printing platform, first  
raise the platform, loosen the plastic head  
screws on the left and right sides of the  
filament tray, and remove the tray.  
2. loosen the four screws on the connection  
plate of the modeling platform board and  
press the A4 paper against the printing  
screen. Press Settings → Z-axis Movement →  
Leveling (refer to the 2-step operation for  
leveling the platform) to check whether the  
platform fits evenly with the paper.  
3. After confirming that the A4 paper fits  
evenly, tighten the four screws on the  
platform.  
Note: The printing platform is already leveled at the factory. If you need to re-level it due to transportation or other reasons, please follow the above-mentioned  
steps. (The user needs to prepare a piece of flat A4 paper by themselves.)  
07  
8. Leveling the Platform 2  
Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official  
website of the latest firmware Ul as the standard.  
07  
9. Loading the Filament  
Pour the UV photosensitive resin for the 3D printer into the tray. Container capacity: 140 ml / 170 ml / 225 ml / 285 ml.  
140ml  
170ml  
225ml  
285ml  
Q&A: How can I replace the filament?  
Warning: Please wear gloves before loading the filament, as  
photosensitive resin is irritating to skin.  
Gently remove the tray and pour the remaining resin into the container. Clean  
the tray, pour in new resin, and then put the tray back into the printer.  
08  
10. Replacing the Release Film  
Parameters  
a. Remove the 14 screws at the bottom of the filament  
tray to remove the worn-out release film.  
Specifications  
b. Take. Remove the protective film on both sides of the  
release film and take a new release film, and then place  
the new release film between the two steel rings.  
Dimensions: 140 mm x 200 mm  
Thickness: 0.15 to 0.2 mm  
c. Put the installed steel rings back into the filament tray  
and tighten the 14 screws.  
d. The installed release film is as shown in the images  
below.  
Light Transmittance: 95%  
(Light Transmittance)  
08  
11. First Printing  
.
1. Slicer  
1. Open the slicer software of LCD 3D printer, clickopenon  
the left of the screen and add model file.  
2. If the model needs to add support, click the upper left icon  
to set corresponding parameters.  
3. Click icon ①→Setting slice printing parameters②→ClickSlice”  
4 waiting for slice to be finished→save thesliced file  
(You are welcome to find more details of slicing  
tutorial on the official website www.creality.com).  
Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official  
website of the latest firmware Ul as the standard.  
09  
12. First Printing  
ctb(.ctb)  
3D objects  
file name  
Save type  
preservation  
cancel  
Hide Folder  
2. Print  
USB port  
2. Insert the USB drive → select the file  
→ press the Start button.  
1. Generate cxdlp fileand save the file to U disk;  
Note: The current interface is for reference only, due to the continuous upgrading of functions, the actual to the official website  
of the latest firmware Ul as the standard.  
Warning: The printer must not be shaken during the printing process, otherwise the printing quality may be compromised.  
10