Operating instructions
for dishwashers
To avoid the risk of accidents or damage to the appliance, it is essential
to read these instructions as well as the installation plan before it is in‐
stalled and used for the first time.
en-AU, NZ
HG05
M.-Nr. 09 867 820
Contents
Guide to the appliance........................................................................................... 6
Appliance overview.................................................................................................. 6
Warning and Safety instructions .......................................................................... 8
Caring for the environment................................................................................. 17
Before using for the first time............................................................................. 19
Opening the door................................................................................................... 19
Filling the salt reservoir..................................................................................... 24
Salt indicator..................................................................................................... 25
Adding rinse aid................................................................................................ 26
Setting the rinse aid dosage............................................................................. 28
Loading the dishwasher ...................................................................................... 29
Dishwashers with cutlery tray........................................................................... 37
Comparison tests................................................................................................. 41
Standard height with cutlery tray........................................................................... 41
3
Contents
Operation .............................................................................................................. 47
Switching on the dishwasher................................................................................. 50
Starting the programme......................................................................................... 51
Energy management.............................................................................................. 52
Programme finished............................................................................................... 52
Programme options ............................................................................................. 55
Short ................................................................................................................ 55
DetergentAgent...................................................................................................... 55
Delay start.............................................................................................................. 57
Programme chart................................................................................................. 62
Cleaning and care................................................................................................ 66
Cleaning the door front.......................................................................................... 67
Checking the filters in the wash cabinet................................................................ 68
Problem solving guide......................................................................................... 71
Technical problems................................................................................................ 71
Water drainage fault............................................................................................... 73
Unsatisfactory washing result................................................................................ 76
Maintenance......................................................................................................... 79
4
Contents
After sales service ............................................................................................... 81
Repairs................................................................................................................... 81
Optional accessories........................................................................................... 82
Electrical connection........................................................................................... 84
Water connection................................................................................................. 85
Drainage................................................................................................................. 86
Technical data ...................................................................................................... 87
5
Guide to the appliance
Appliance overview
a
g
h
i
j
Upper spray arm (not visible)
Filter combination
Data plate
b
Cutlery tray (depending on model)
c
Upper basket
Rinse aid reservoir
d
Middle spray arm
Dual compartment detergent dis‐
penser
e
Air inlet for drying (depending on
model)
k
Salt reservoir
f
Lower spray arm
6
Guide to the appliance
Control panel
a
e
f
Programme selection
Short button with indicator light
b
Display
Delay start button with indicator
light
c
Check/Refill indicators
g
h
Programme selector button
d
Start button with indicator light
On/Off button
These operating instructions apply to several different dishwasher models with
different heights.
The specific dishwasher models are referred to as follows:
Standard = 80.5 cm high dishwashers (integrated)
and 84.5 cm high dishwashers (freestanding)
XXL = 84.5 cm high dishwashers (integrated)
7
Warning and Safety instructions
This dishwasher complies with current safety requirements. Inap‐
propriate use can, however, lead to personal injury and damage to
property.
To avoid the risk of accidents and damage to the dishwasher,
please read the installation plan and the operating instructions
carefully before it is installed and used for the first time. They con‐
tain important information on its installation, safety, use and main‐
tenance.
Keep the installation plan and the operating instructions in a safe
place and pass them on to any future owner.
Miele cannot be held liable for damage caused by non-compli‐
ance with this information.
8
Warning and Safety instructions
Correct application
This appliance is designed for domestic use and for use in similar
environments by guests in hotel or motel rooms, bed & breakfasts
and other typical living quarters. This does not include common/
shared facilities or commercial facilities within hotels, motels or bed
& breakfasts.
This dishwasher is not suitable for outdoor use.
It must only be used as specified in these operating instructions
for cleaning domestic crockery and cutlery. Any other usage is not
supported by the manufacturer and could be dangerous.
This appliance is not intended for use by persons (including chil‐
dren) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervi‐
sion or instruction concerning its use by a person responsible for
their safety, and are able to recognise the dangers of misuse.
9
Warning and Safety instructions
Safety with children
Young children must not be allowed to use this appliance.
Older children may only use the appliance when its operation has
been clearly explained to them and they are able to use it safely, rec‐
ognising the dangers of misuse.
Cleaning work may only be carried out by older children under the
supervision of an adult.
Children should be supervised to ensure that they do not play
with the appliance. Keep small children away from the appliance at
all times to avoid the risk of injury. There is the risk that children may
lock themselves in the dishwasher.
If the automatic door opening mechanism (depending on model)
is active, keep young children away from the area in which the door
opens. Danger of injury in the unlikely event of a fault with the open‐
ing mechanism.
Danger of suffocation! Children may be able to wrap themselves
in packing material or pull it over their heads with the risk of suffoca‐
tion. Keep children away from any packing material.
Keep detergent and other household agents out of the reach of
children at all times. Some dishwasher detergents are strongly alka‐
line and contain irritants and corrosive ingredients. They can be ex‐
tremely dangerous if swallowed, and can cause burning in the
mouth, nose and throat, or inhibit breathing. Avoid contact with the
skin and eyes. Keep children away from the dishwasher when the
door is open. There could still be detergent residues in the cabinet
or dispenser. Seek medical advice immediately if your child has
swallowed or inhaled detergent, e.g. Poisons Information Centre
(Australia) or National Poisons Centre (NZ).
10
Warning and Safety instructions
Technical safety
Repairs and other work by unqualified persons could be danger‐
ous. Installation, maintenance work and repairs to electrical applian‐
ces must only be carried out by a Miele approved service technician.
Before installation, check the dishwasher for visible signs of dam‐
age. Under no circumstances should you use a damaged dishwash‐
er. A damaged dishwasher could be dangerous.
The electrical safety of this appliance can only be guaranteed
when continuity is complete between it and an effective earthing
system. It is most important that this basic safety requirement is
present and regularly tested and, where there is any doubt, the elec‐
trical system in the house should be checked by a qualified electri‐
cian.
Miele cannot be held liable for the consequences of an inadequate
earthing system (e.g. electric shock).
Reliable and safe operation of this dishwasher can only be assur‐
ed if it has been connected to the mains electricity supply.
The dishwasher must only be plugged into the electricity supply
via a suitable switched socket. The electrical socket must be easily
accessible after the dishwasher is installed so that it can be discon‐
nected from the electricity supply at any time.
There must be no electrical sockets behind the dishwasher. Dan‐
ger of overheating and fire risk if the dishwasher were to be pushed
up against a plug.
The dishwasher must not be installed under a cooktop. The high
radiant temperatures which are sometimes generated by a cooktop
could damage the dishwasher. For the same reason, it should not be
installed next to open fires or other appliances which give off heat,
such as heaters etc.
11
Warning and Safety instructions
To avoid the risk of damage to the dishwasher, make sure that the
connection data on the data plate (fuse rating, voltage and frequen‐
cy) matches the mains electricity supply before connecting the dish‐
washer to the mains. Consult a qualified electrician if in any doubt.
Do not connect the dishwasher to the mains supply until it has
been fully installed and any adjustment has been made to the door
springs.
The dishwasher may only be operated if the door opening mecha‐
nism is working correctly. Otherwise there could be a risk of injury
whilst the automatic door opening mechanism (depending on model)
is active.
To check that the door opening mechanism is working correctly:
– the door springs must be adjusted equally on both sides. They
are correctly adjusted when the door remains stationary when left
half open (approx. 45° opening angle). It is also important that the
door cannot fall open.
– the door locking pins automatically retract when the door opens
at the end of the drying phase.
Do not connect the appliance to the mains electricity supply by a
multi-socket adapter or an extension lead. These do not guarantee
the required safety of the appliance (e.g. danger of overheating).
This appliance must not be installed and operated in mobile in‐
stallations (e.g. on a ship).
Do not install the dishwasher in a room where there is a risk of
frost. Frozen hoses may burst or split. The reliability of the electronic
control unit may be impaired at temperatures below freezing point.
To avoid any damage to the appliance, the dishwasher must only
be operated when it is connected to a fully vented plumbing system.
The plastic housing of the water connection contains an electrical
valve. The housing must not be dipped in water.
12
Warning and Safety instructions
There are electrical wires in the water inlet hose. Do not cut the
water inlet hose, even if it is too long.
The integrated Waterproof system offers protection from water
damage, provided the following conditions are met:
– The dishwasher is correctly installed and plumbed in.
– The dishwasher is properly maintained and parts are replaced
where it can be seen that this is necessary.
– The tap has been turned off when the appliance is not used for a
longer period of time (e.g. during holidays).
The Waterproof system will work even if the appliance is switched
off. However, the appliance must remain connected to the electricity
supply.
The water pressure (flow pressure at the connection point) must
be between 30 and 1000 kPa (0.3 and 10 bar).
A damaged appliance could be dangerous. If the dishwasher gets
damaged, switch it off at the mains and call Miele.
The manufacturer's warranty will be invalidated if the appliance is
not repaired by a Miele approved service technician.
Faulty components must only be replaced by genuine Miele spare
parts. The manufacturer can only guarantee the safety of the appli‐
ance when Miele replacement parts are used.
During installation, maintenance and repair work, the appliance
must be disconnected from the mains electricity supply.
If the connection cable is damaged, it must be replaced with a
special cable of the same type (available from Miele) by a Miele au‐
thorised service technician only in order to avoid a hazard.
13
Warning and Safety instructions
In areas which may be subject to infestation by cockroaches or
other vermin, pay particular attention to keeping the appliance and
its surroundings in a clean condition at all times. Any damage which
may be caused by cockroaches or other vermin will not be covered
by the warranty.
Correct installation
The dishwasher must be installed and connected in compliance
with the installation instructions.
Be careful when installing the dishwasher. Wear protective
gloves to avoid injury on any sharp metal components.
The dishwasher must be correctly aligned to ensure problem-free
operation.
In order to ensure stability, built-under and integrated dishwash‐
ers must only be installed under a continuous worktop which is se‐
cured to adjacent cabinetry.
If you want to convert your freestanding dishwasher to a built-un‐
der ("U") model, you will need to order the appropriate conversion
kit. If you remove the existing plinth, you must replace it with a U-
model plinth. This is necessary to avoid the risk of injury caused by
protruding metal parts.
The door springs on either side need to be evenly adjusted. They
are correctly adjusted if the half-opened door (approx. 45° door
opening angle) remains in this position when it is released. The door
must not fall down under its own weight.
The appliance may only be used with correctly adjusted door
springs.
14
Warning and Safety instructions
Correct use
Do not use solvents in the dishwasher. Danger of explosion!
Do not inhale or ingest dishwasher detergent. Some dishwasher
detergents are strongly alkaline and contain irritants or corrosive in‐
gredients. They can be extremely dangerous if swallowed, and can
cause burning in the nose, mouth and throat, or inhibit breathing.
Avoid contact with the skin and eyes. Seek medical advice immedi‐
ately if detergent has been swallowed or inhaled, e.g. Poisons Infor‐
mation Centre (Australia) or National Poisons Centre (NZ).
Avoid leaving the door open unnecessarily as someone could trip
over it and be injured by it.
Do not sit or lean on the opened door. This could cause the dish‐
washer to tip and be damaged, and you could get injured.
Dishes can be very hot at the end of a programme. Allow them to
cool until they are comfortable enough to handle before unloading.
Only use detergent and rinse aid formulated for domestic dish‐
washers. Do not use washing-up liquid.
Do not use commercial or industrial detergents as these may
cause damage, and there is a risk of a severe explosive chemical re‐
action (such as an explosive oxyhydrogen gas reaction).
Do not fill the rinse aid reservoir with powder or liquid detergent.
This will cause serious damage to the reservoir.
Inadvertently filling the salt reservoir with powder or liquid dish‐
washer detergent will damage the water softener. Make sure you
have picked up the correct packet of dishwasher salt before filling
the salt reservoir!
Only use special coarse grained dishwasher salt for reactivation.
Do not use other salts such as cooking salt, agricultural grade or
gritting salt. These may contain insoluble additives which can impair
the functioning of the water softener.
15
Warning and Safety instructions
In an appliance with a cutlery basket (depending on model) cut‐
lery is cleaned and dried more efficiently if placed in the basket with
the handles downwards. However, to avoid the risk of injury, place
knives and forks etc. with the handles upwards.
Plastic items which cannot withstand being washed in hot water,
such as disposable plastic containers, or plastic cutlery and crock‐
ery should not be cleaned in the dishwasher. The high temperatures
in the dishwasher may cause them to melt or lose shape.
If you use the "FlexiTimer/Delay start" option (depending on mod‐
el), make sure that the dispenser is dry before adding detergent.
Wipe dry if necessary. Detergent will clog if poured into a damp dis‐
penser and may not be thoroughly dispersed.
Please observe the information given in "Technical data" regard‐
ing the capacity of the dishwasher.
Accessories
Use only genuine original Miele spare parts. If spare parts or ac‐
cessories from other manufacturers are used, the warranty will be in‐
validated, and Miele cannot accept liability.
Disposal of your old dishwasher
Make the door lock inoperative so that children cannot acciden‐
tally shut themselves in. Remove or destroy the locking bracket of
the door lock, and make appropriate arrangements for the disposal
of the appliance.
16
Caring for the environment
Disposal of the packing mate‐
rial
Disposing of your old appli‐
ance
The packaging is designed to protect
the appliance from damage during
Electrical and electronic appliances of‐
ten contain materials which, if handled
transportation. The packaging materials or disposed of incorrectly, could be po‐
used are selected from materials which tentially hazardous to human health and
are environmentally friendly for disposal to the environment. They are, however,
and should be recycled.
essential for the correct functioning of
your appliance. Therefore, please do
not dispose of your old appliance with
your household waste.
The packaging consists of the following
materials:
Outer packaging:
– Corrugated cardboard made from up
to 100% recyclable material:
or: Polyethylene (PE) shrink wrap
– Polyproplylene (PP) strapping
Inner packaging:
– Chlorine and fluorine free expanded
polystyrene (EPS)
Please dispose of it at your local com‐
munity waste collection / recycling cen‐
tre.
– Base, lid frame and support battens
made from untreated natural wood
from renewable forests
Ensure that your old appliance presents
no danger to children while being stor‐
ed for disposal.
– Polyethylene (PE) protective wrap
Recycling the packaging reduces the
use of raw materials in the manufactur‐
ing process and also reduces the
To enable sorting by type of plastic for
recycling, all plastic parts of the appli‐
ance are labelled with international
amount of waste in landfill sites. Rather standard symbols.
than just throwing these materials
away, please ensure they are recycled.
Ensure that any plastic wrap‐
pings, bags, etc. are disposed of
safely and kept out of the reach of
babies and young children. Danger
of suffocation.
17
Caring for the environment
Energy-saving dishwashing
This dishwasher is exceptionally eco‐
nomical in its use of water and electrici‐
ty.
You can make the most of your appli‐
ance by following these tips:
– For most economical dishwashing,
make full use of the baskets without
overloading the dishwasher.
– Choose the programme to suit the
type of crockery being washed and
the degree of soiling.
– Select the ECO programme for ener‐
gy-saving dishwashing. This pro‐
gramme is the most efficient in terms
of its combined energy and water
consumption at cleaning normally
soiled crockery.
– Follow the detergent manufacturer's
recommendations on detergent dos‐
age.
– When using powder or liquid deter‐
gent you can use 1/3 less detergent if
baskets are only half full.
– If your household water system is
suitable, this dishwasher can be con‐
nected to a hot water supply for fur‐
ther economies. If the water is heated
by solar panels, for example, this
would be energy efficient.
However, if your water is heated by
electricity, we would recommend
connection to cold water.
You can find further tips on energy-
saving dishwashing in "Miele's guide
to dishwashing".
18
Before using for the first time
Opening the door
Closing the door
Push the baskets right in.
Then lift the door upwards and push
until it clicks into position.
Danger of injury!
Do not put your hand inside the door
as it is closing.
Safety lock
Use the safety lock to prevent children
opening the dishwasher door.
To open the door, reach under the
door grip and pull.
If the door is opened during operation,
all functions are automatically interrup‐
ted.
Water in the dishwasher may be
hot. Danger of scalding!
Only open the door during operation
if absolutely necessary and exercise
extreme caution when doing so.
To lock the door, push the slide un‐
derneath the door grip to the right.
To unlock the door, push the slide to
the left.
19
Before using for the first time
Enter the water hardness below:
____________mmol/l
Water softener
In order to achieve good cleaning re‐
sults, the dishwasher needs to operate
with soft water. Hard water results in a
build-up of calcium deposits on crock‐
ery and in the dishwasher.
The dishwasher is programmed at the
factory for a water hardness level of
0.2 mmol/l (1 °d - German scale).
If this setting corresponds to the hard‐
ness of your water, you do not need to
do anything more.
Mains water with a hardness level high‐
er than 0.7 mmol/l (4 °d - German
scale) needs to be softened. This takes
place automatically in the integrated
water softener. The water softener in
the dishwasher is suitable for a water
hardness level of up to 12.6 mmol/l (70
°d - German scale).
However, if you have a different water
hardness, you must adjust the water
softener to match your water hardness.
– The water softener requires dish‐
washer salt.
Depending on the water hardness
level (< 3.8 mmol/l, or 21 °d - Ger‐
man scale), dishwasher salt is not re‐
quired if combination tablets are be‐
ing used (see "Operation - Deter‐
gent").
– The dishwasher must be program‐
med for the water hardness level in
your area.
– Your local water authority will be able
to advise you of the water hardness
level in your area.
– Where the water hardness fluctuates,
e.g. between 1.8 and 2.7 mmol/l (10 -
15 °d - German scale), always pro‐
gramme the dishwasher to the higher
value (2.7 mmol/l or 15 °d in this ex‐
ample).
In the event of a fault, it will help the
service technician if you know the hard‐
ness of your local water supply.
20
Before using for the first time
Displaying and setting the water
hardness level
The value which has been set for the
water hardness is shown as a figure af‐
ter in the display (see chart).
Switch the dishwasher off with the
button if it is switched on.
will start flashing in the display.
This is the factory default setting of
0.2 mmol/l (1 °d - German scale).
Press the Start button in and, whilst
holding it in, switch the dishwasher
on using the button.
Keep the Start button pressed in for
at least four seconds until the Start
indicator light comes on.
Use the Start button to select the val‐
ue which equates to your water hard‐
ness level.
Each press of the button moves you
up a level. When the highest water
hardness level is reached, the setting
starts from the beginning again.
If this does not happen, start the proce‐
dure from the beginning again.
Press the Delay start button twice.
The setting is now stored in memory.
The indicator light will flash rapidly
twice at intervals.
Switch the dishwasher off with the
button.
21
Before using for the first time
°d
1
mmol/l
0.2
0.4
0.5
0.7
0.9
1.1
1.3
1.4
1.6
1.8
2.0
2.2
2.3
2.5
2.7
2.9
3.1
3.2
3.4
3.6
°f
2
Display
1
°d
21
mmol/l
3.8
°f
38
Display
21
2
4
2
22
4.0
40
22
3
5
3
23
4.1
41
23
4
7
4
24
4.3
43
24
5
9
5
25
4.5
45
25
6
11
13
14
16
18
20
22
23
25
27
29
31
32
34
36
6
26
4.7
47
26
7
7
27
4.9
49
27
8
8
28
5.0
50
28
9
9
29
5.2
52
29
10
11
12
13
14
15
16
17
18
19
20
10
11
12
13
14
15
16
17
18
19
20
30
5.4
54
30
31
5.6
56
31
32
5.8
58
32
33
5.9
59
33
34
6.1
61
34
35
6.3
63
35
36
6.5
65
36
37-45
46-60
61-70
6.6-8.0
8.2-10.7
10.9-12.5
66-80
82-107
109-125
45
60
70
22
Before using for the first time
Before using the appliance for
the first time, you require:
– approx. 2 litres of water,
If the water hardness in your area is
constantly lower than 0.9 mmol/l
(5 °d), you do not need to add dish‐
washer salt. The prompt to add dish‐
washer salt will be switched off auto‐
matically. The water softener must,
however, still be programmed to cor‐
respond to the water hardness level in
your area.
– approx. 2 kg dishwasher salt,
– domestic dishwasher detergent,
– rinse aid formulated for domestic
dishwashers.
Every dishwasher is tested at the fac‐
tory. There will be residual water in the
appliance from this test. It is not an in‐
dication that it has been used previ‐
ously.
Dishwasher detergent will dam‐
age the water softener.
Do not fill the salt reservoir with
powder or liquid detergent.
Only use special coarse grained
dishwasher salt for reactivation,
as other salts (e.g. cooking salt, agri‐
cultural grade or gritting salt) may
contain insoluble additives which
can impair the functioning of the wa‐
ter softener.
Dishwasher salt
In order to achieve good cleaning re‐
sults, the dishwasher needs to operate
with soft water. Hard water results in a
build-up of calcium deposits on crock‐
ery and in the dishwasher.
Mains water with a hardness level high‐
er than 0.7 mmol/l (4 °d - German
scale) needs to be softened. This takes
place automatically in the integrated
water softener. The water softener in
the dishwasher is suitable for a water
hardness level of up to 12.6 mmol/l
(70 °d - German scale).
The water softener requires dishwasher
salt.
Depending on the water hardness level
(< 3.8 mmol/l, or 21 °d - German scale),
dishwasher salt is not required if combi‐
nation tablets are being used (see "Op‐
eration - Detergent").
23
Before using for the first time
Filling the salt reservoir
Before filling the salt reservoir with
dishwasher salt for the first time, you
must fill it with approx. 2 litres of wa‐
ter to enable the salt to dissolve.
Once the dishwasher has been used,
there is always sufficient water in the
reservoir.
Remove the lower basket and un‐
screw the salt reservoir cap.
Water or saline solution will run out
of the reservoir when the cap is re‐
moved.
It should therefore only be removed
in order to refill the salt reservoir.
Place the funnel provided over the
salt reservoir and carefully fill with
dishwasher salt until the reservoir is
full. The salt reservoir holds approx. 2
kg of salt depending on the brand
used.
Fill the reservoir with approx. 2 litres
of water (first use only).
Clean any excess dishwasher salt
from around the reservoir opening
and then screw the cap on again
firmly.
Immediately after filling the salt reser‐
voir, run the Quick wash programme
with the Short programme option se‐
lected and without any crockery in
the dishwasher, to remove any traces
of salt from the cabinet.
24
Before using for the first time
Salt indicator
If you only ever use multi-function
combination products in your dish‐
washer, you can switch off both refill
reminders for salt and rinse aid if you
wish (see "Programme options -
Switching off the refill indicators").
Fill the salt reservoir with dishwasher
salt when the Salt indicator light
comes on (If it comes on during a
programme, wait until the end of the
programme).
Risk of corrosion!
If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to add
dishwasher salt and rinse aid and to
switch the refill indicators back on.
Immediately after filling the salt res‐
ervoir, run the Quick wash pro‐
gramme with the Short programme
option selected and without any
crockery in the dishwasher to re‐
move any traces of salt from the
cabinet.
After the salt reservoir has been filled,
the refill indicator may still be lit up if
the salt concentration has not yet
reached the correct level. It will go out
when the correct concentration is
reached.
The refill indicator will be switched off if
you have programmed the dishwasher
for a water hardness below 0.9 mmol/l
(5 °d - German scale).
25
Before using for the first time
Rinse aid
If you only ever use combination
products containing rinse aid in your
dishwasher, you do not need to add
rinse aid.
Rinse aid is necessary to ensure water
does not cling and leave marks on
crockery during the drying phase and
helps crockery dry faster after it has
been washed.
Adding rinse aid
Rinse aid is poured into the storage res‐
ervoir and the amount set is dispensed
automatically.
Inadvertently filling the rinse aid
reservoir with powder or liquid deter‐
gent will damage the reservoir. Only
pour rinse aid formulated for domes‐
tic dishwashers into the reservoir.
Alternatively, it is possible to use
– household vinegar with a max. 5%
acid content
Press the button on the lid of the
rinse aid reservoir in the direction of
the arrow until the flap springs open.
or
– liquid citric acid up to 10% acid con‐
tent
The resulting rinsing and drying quality
will not, however, be as good as when
rinse aid is used.
Do not use vinegar with a higher
acid content (e.g. vinegar essence
25% acid).
This would damage the dishwasher.
26
Before using for the first time
Add rinse aid reminder
When the Rinse aid indicator light
comes on, the reservoir contains suffi‐
cient rinse aid for 2 - 3 programmes on‐
ly.
Add rinse aid in plenty of time.
If you only ever use multi-function
combination products in your dish‐
washer, you can switch off both refill
reminders for salt and rinse aid if you
wish (see "Programme options -
Switching off the refill indicators").
Add rinse aid only until it is visible in
the opening.
If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to add
dishwasher salt and rinse aid and to
switch the reminders back on.
The rinse aid reservoir holds approx.
110 ml.
Close the flap firmly so that it clicks
into place. Otherwise water can enter
the rinse aid reservoir during a pro‐
gramme.
Wipe up any spilled rinse aid. This
prevents over-foaming occurring dur‐
ing the next programme.
27
Before using for the first time
Setting the rinse aid dosage
Switch the dishwasher off with the
button, if it is switched on.
You can adjust the rinse aid dosage for
best results.
Press the Start button in and, whilst
holding it in, switch the dishwasher
on using the button.
Keep the Start button pressed in for
at least 4 seconds until the Start indi‐
cator light comes on.
The rinse aid dosage is set in stages
from 0 to 6. It is set to 3 at the factory.
This is the recommended setting.
If the "Adjust Sensor wash" programme
function (depending on model) has
been activated, the amount of rinse aid
dispensed in the Sensor wash pro‐
gramme can be higher than that set.
If this does not happen, start the proce‐
dure from the beginning again.
Press the button 3 times.
If spots appear on crockery and glass‐
ware:
The indicator will flash rapidly 3
times at intervals.
Increase the rinse aid dosage.
The dosage set will appear in the dis‐
play after .
If clouding or smearing appears on
crockery and glassware:
The flashing sequence will appear in
the display.
Decrease the rinse aid dosage.
This indicates the factory default setting
3.
Use the Start button to select the set‐
ting required.
Each press of the button moves you
up a level. After reaching the highest
value, the counter starts from the be‐
ginning again.
The setting is now stored in memory.
Switch the dishwasher off with the
button.
28
Loading the dishwasher
– The spray arms must not be blocked
by items which are too tall or hang
through the baskets. If in doubt, test
for free movement by manually rotat‐
ing the spray arms.
Notes
Remove coarse food residues from
crockery.
There is no need to rinse items under
running water.
– Make sure that small items cannot
fall through the holders in the bas‐
kets.
Do not wash items soiled with
ash, sand, wax, lubricating grease or
paint in the dishwasher. Ash does
not dissolve and is distributed in the
wash cabinet. Wax, sand, lubricating
grease and paint cause damage to
the dishwasher.
Small items, e.g. lids, should there‐
fore be placed in the cutlery tray or
cutlery basket (depending on model).
Some foodstuffs may contain natural
dyes, e.g. carrots, tomatoes or toma‐
to sauce. Plastic items in the dish‐
washer may discolour if large quanti‐
ties of these foodstuffs find their way
into the dishwasher on the crockery.
The stability of plastic items is not
affected by this discolouration.
Cleaning silver cutlery in the dish‐
washer may also cause plastic items
to discolour.
Crockery can be loaded anywhere in
the baskets, but the following notes
should be observed:
– Do not place crockery and cutlery in‐
side other pieces where they may be
concealed.
– Load the crockery so that water can
access all surfaces. This ensures that
they get properly cleaned.
– Make sure that all items are securely
positioned.
– Hollow items such as cups, glasses,
pans, etc. must be inverted in the
basket.
– Tall, narrow, hollow items, e.g. cham‐
pagne glasses, should be placed in
the centre of the basket to ensure
better water coverage.
– Wide based items should be placed
at an angle so that water can run off
them freely.
29
Loading the dishwasher
Items not suitable for dishwashers:
Aluminium components (e.g.
rangehood grease filters) must not
be cleaned with caustic alkaline
commercial or industrial cleaning
agents.
These may damage the material, or
in extreme cases, there is a risk of a
severe explosive chemical reaction
(such as an explosive oxyhydrogen
gas reaction).
– Wooden cutlery and crockery or
items with wooden parts: these may
discolour and fade. The glue used in
these items is not dishwasher-proof
and wooden handles may come
loose after being washed in a dish‐
washer.
– Craft items, antiques, valuable vases
and decorative glassware are also
not suitable for dishwashers.
Useful tip: When purchasing new
crockery and cutlery, make sure they
are dishwasher-proof.
– Plastic items which are not heat-re‐
sistant: the high temperatures in the
dishwasher may cause them to melt
or lose shape.
Glass care
– Clouding may occur on glasses after
frequent washing. If delicate glass‐
ware is washed in the dishwasher,
ensure that only very low tempera‐
tures are used (see programme
chart), or a special glass-care pro‐
gramme is used (depending on mod‐
el). This will reduce the risk of cloud‐
ing.
– Copper, brass, tin and aluminium
items may discolour or become matt.
– Colours painted over a glaze may
fade after a number of washes.
– Delicate glassware and glassware
containing lead crystal: clouding may
occur over time.
Please note
– Purchase glassware which is dish‐
washer-safe (e.g. Riedel glassware).
Silverware previously cleaned with a
silver polish may still be damp or spot‐
ted at the end of a programme, where
water has not run off smoothly. It may
need to be rubbed dry with a soft cloth.
– Use detergents with glass protective
additives (e.g. Miele CareCollection
tabs).
– Visit "http://www.mieleglass‐
care.com/international/en/glasscare/
english" for more information on
glass care.
Silver which has been in contact with
foods containing sulphur can discolour.
These include egg yolk, onions, mayon‐
naise, mustard, pulses, fish, fish brine
and marinades.
30
Loading the dishwasher
Cup rack
Upper basket
To make room for tall items, raise the
See "Loading the dishwasher / Load‐
ing examples" for examples of how to
load crockery and cutlery.
rack upwards.
Glasses can be arranged along the po‐
sitioning rail of the cup rack to give
them some support during the pro‐
gramme.
For safety reasons, do not oper‐
ate the dishwasher without the upper
and lower baskets in place (except
when running the Tall items pro‐
gramme, if available).
Lower the cup rack and lean the
glasses against it.
Use the upper basket for small, light‐
weight and delicate items such as
cups, saucers, glasses, dessert
bowls, etc.
Shallow pans or casserole dishes can
also be placed in the upper basket.
Long items such as soup ladles, mix‐
ing spoons and long knives should
be placed lying down across the front
of the upper basket.
31
Loading the dishwasher
Adjusting the upper basket
Depending on the setting of the upper
basket, the following plate dimensions
can be accommodated.
In order to gain more space for taller
pieces of crockery in the bottom or up‐
per basket, the upper basket can be
adjusted on three levels with 2 cm be‐
tween each level.
Dishwashers with cutlery basket
(see data plate for model number)
Upper
basket
level
Plate in cm
Upper basket
The upper basket can also be set at an
angle with one side high and the other
side low. This can be useful to help pre‐
vent water being left in deep dishes etc.
Ensure, however, that the basket can
be inserted smoothly into the cabinet. It
is better to adjust the basket before
loading it.
Lower
basket
Stand‐
ard
XXL
Top
20
22
24
24
26
28
31 (35*)
29
Middle
Bottom
27
Pull out the upper basket.
Dishwashers with cutlery tray
(see data plate for model number)
Upper
basket
level
Plate in cm
Upper basket
Lower
basket
Stand‐
ard
XXL
Top
15
17
19
19
21
23
31 (35*)
29
Middle
Bottom
27
* When tilted, plates of up to 35 cm can be
accommodated (see "Lower basket").
To raise the upper basket:
Pull the basket up until it clicks into
place.
To lower the upper basket:
Pull upwards on the levers at either
side of the upper basket.
Adjust the basket to the desired
height and then push the levers se‐
curely back down into position.
32
Loading the dishwasher
MultiComfort area
Lower basket
The rear section of the lower basket is
used for washing cups, glasses, plates,
pots and pans.
See "Loading the dishwasher / Load‐
ing examples" for examples of how to
load crockery and cutlery.
The glass rack can be raised to make
more room for tall items.
For larger and heavier items such as
plates, serving platters, saucepans,
bowls, etc.
Glasses, cups and small items such
as saucers can also be placed in the
lower basket. Do not place thin, deli‐
cate glassware in the lower basket.
Stem glassware, e.g. wine glasses or
champagne flutes, can be leaned
against the glass rack or suspended
from it.
You can set the glass rack at two differ‐
ent heights.
Place large platters and dishes in the
centre of the lower basket.
Slide the glass rack to the desired
height until the catches click into
place at the top.
When tilted, plates up to 35 cm in di‐
ameter can be accommodated.
33
Loading the dishwasher
Hinged spikes (depending on model)
The spikes at the front are used for
washing plates, soup bowls, platters,
dessert bowls and saucers.
Both rows of spikes can be lowered to
make more room for large items, e.g.
pots, pans and dishes.
Press the yellow lever downwards ,
and then lower the spikes .
34
Loading the dishwasher
Cutlery
3D cutlery tray (depending on model)
See "Loading the dishwasher / Load‐
ing examples" for examples of how to
load crockery and cutlery.
Arrange the cutlery in the tray as
shown.
To make unloading much easier, cutlery
should be grouped in zones, one for
knives, one for forks, one for spoons,
etc.
If spoon handles do not fit between the
holders, then lay them the other way
round.
Spoon heads should be placed in con‐
tact with at least one of the serrated re‐
tainers on the base of the cutlery tray to
ensure that water runs off them freely.
The upper spray arm must not be
blocked by items which are too big
(e.g. cake slices).
The side sections of the tray can be
moved into the middle to accommodate
tall items of crockery in the upper bas‐
ket.
You can use the yellow slide to adjust
the height of the middle section of the
cutlery tray to make more room for
large items of cutlery, such as serving
spoons and ladles.
35
Loading the dishwasher
Cutlery basket (depending on model)
Fit it onto the cutlery basket if re‐
quired.
The cutlery basket can be placed any‐
where on the front rows of spikes in the
lower basket.
To avoid the risk of injury, knives and
forks should be placed with the han‐
dles upwards in the basket. However,
cutlery placed handle down in the
basket will come out cleaner and dri‐
er.
Place small items of cutlery in the in‐
dividual slots on three sides of the
cutlery basket.
Cutlery insert for the cutlery basket
Insert cutlery with the handles facing
Use the insert supplied for heavily
soiled items of cutlery. The insert sepa‐
rates the items so that they can be
more easily accessed by water.
downwards.
Distribute them evenly along the in‐
sert.
36
Loading the dishwasher
Cutlery tray
Heavily soiled items
38
Loading the dishwasher
Cutlery basket
Heavily soiled items
40
Comparison tests
Standard height with cutlery tray
Test standard:
AS/NZS 2007.1:2005, AS/NZS 2007.2:2005;
AS/NZS 6400:2005
Standard programme
for energy label comparison
tests:
ECO
Capacity:
14 place settings
32.5 g in Compartment II
Setting 3
Detergent quantity:
Rinse aid dispensing:
You can find information on adjusting the rinse aid dosage in the "Rinse aid"
section of this booklet.
Drying measurements:
Door ajar using a block of approximately
50 mm upon completion of dry test.
Upper basket level:
Position:
Bottom
Jumbo cup rack
(if available):
Outer position
Loading examples
Pictures illustrating how to load the dishwasher are shown on the following pages.
Picture : Upper basket
Picture : Lower basket
Picture : Cutlery tray
Do not lower or remove the basket inserts.
Remove the bottle holder from the lower basket
(if available).
41
Comparison tests
Capacity
14
42
Comparison tests
43
Comparison tests
XXL height with cutlery tray
Test standard:
AS/NZS 2007.1:2005, AS/NZS 2007.2:2005;
AS/NZS 6400:2005
Standard programme
for energy label comparison
tests:
ECO
Capacity:
15 place settings
33.7 g in Compartment II
Setting 3
Detergent quantity:
Rinse aid dispensing:
You can find information on adjusting the rinse aid dosage in the "Rinse aid"
section of this booklet.
Drying measurements:
Door ajar using a block of approximately
50 mm upon completion of dry test.
Upper basket level:
Position:
Bottom
Jumbo cup rack
(if available):
Outer position
Loading examples
Pictures illustrating how to load the dishwasher are shown on the following pages.
Picture : Upper basket
Picture : Lower basket
Picture : Cutlery tray
Do not lower or remove the basket inserts.
Remove the bottle holder from the lower basket
(if available).
44
Comparison tests
Capacity
15
45
Comparison tests
46
Operation
You can also buy combination products
(see "Programme options - Detergent‐
Agent", if applicable).
Detergent
Only use detergents formulated
for domestic dishwashers. Do not
use washing-up liquid.
In addition to detergent, these products
contain rinse aid and salt substitutes.
They are available as "3 in 1" or when
they also contain other components
such as glass and stainless steel pro‐
tective additives and enhanced clean‐
ing power, as "5 in 1", "7 in 1", "All in 1"
etc.
Active ingredients
Modern detergents contain various ac‐
tive ingredients, the most important of
which are:
Refer to the manufacturer's packaging
as to whether combination products are
suitable for the water hardness level in
your area.
Please note that the cleaning and dry‐
ing results of combination detergents
can vary greatly.
– Complexing agents to prevent calcifi‐
cation.
– Alkalis to aid the removal of dried on
soiling.
– Enzymes to break down starch and
loosen protein.
– Oxygen based bleaching agents to
remove coloured stains (e.g. tea, cof‐
fee, tomato sauce).
For optimum cleaning and drying re‐
sults, use Miele dishwasher detergent
and add Miele salt and Miele rinse aid
separately. See "Optional accesso‐
ries".
Most dishwasher detergents are mildly
alkaline and contain enzymes and oxy‐
gen based bleaching agents.
Types of detergent:
– Powder and liquid gel detergents.
These detergents allow you to adjust
the amount dispensed according to
the amount of load and level of soil‐
ing.
– Tab detergents. These are suitable
for most levels of soiling.
47
Operation
Detergent dosage
Some dishwasher detergents are
strongly alkaline and contain irritant
or corrosive ingredients which can
cause burning in the nose, mouth
and throat if swallowed, or inhibit
breathing.
Avoid inhalation of powder deter‐
gents and do not ingest dishwasher
detergent. Seek medical advice im‐
mediately if detergent has been
swallowed or inhaled.
Keep detergent and other household
agents out of the reach of children at
all times. Keep children away from
the dishwasher when the door is
open. There could still be detergent
residues in the cabinet. Check that
the detergent dispenser is empty at
the completion of a programme. To
avoid the danger of children coming
into contact with the dishwasher de‐
tergent, only add detergent just be‐
fore starting the programme and
close the door, activating the safety
lock (if your dishwasher is fitted with
one).
Follow the dosage recommended by
the manufacturer on the packaging.
Unless directed otherwise, use one
detergent tab or add 20 to 30 ml de‐
tergent to compartment II, depending
on the level of soiling. With very
heavy soiling you can also add a
small amount of detergent to com‐
partment l.
Tabs may not dissolve completely
when the Quick wash programme (if
available) is used.
Failure to dispense the recommen‐
ded amount of detergent may impair
cleaning results.
48
Operation
Adding detergent
Add the required amount of detergent
and close the flap.
Press the opening catch on the de‐
tergent dispenser. The flap will spring
open.
Make sure that the detergent packag‐
ing is properly closed after use to
avoid it getting damp and becoming
lumpy.
The flap is always open at the end of a
programme.
For information
Compartment I holds max. 10 ml,
Compartment II holds max. 50 ml.
There are marks in Compartment II to
assist with dispensing: 20, 30. The
marks indicate a level of approx. 20 or
30 ml when the door is open in a hori‐
zontal position.
49
Operation
Switching on the dishwasher
Selecting a programme
Make sure the spray arms are not ob‐ Choose your programme according to
structed.
the type of load and how dirty it is.
Close the door.
The different programmes and their
uses are described in the Programme
chart later on in this booklet.
Turn on the tap if it is turned off.
Switch the dishwasher on with the
button.
Use the programme selector button
to select the programme required.
The Start indicator light flashes and the
indicator light comes on next to the
programme selected.
The indicator light for the programme
selected will light up.
The programme duration will appear in
hours and minutes in the display.
You can now select programme op‐
tions (see "Programme options").
If any programme options are selected,
the appropriate indicator lights will light
up.
50
Operation
Starting the programme
Press the Start button.
Display
The duration of the programme selec‐
ted appears in hours and minutes in the
display before the programme begins.
During the programme the time left until
the end of the programme is displayed.
The programme will begin.
The Start indicator light will come on.
A programme should only be cancel‐
led in the first few minutes, if at all.
Otherwise important programme
stages could be omitted.
The programme duration displayed may
vary with the same programme. It is in‐
fluenced by, among other things, the
water temperature at each intake, the
reactivation process, the type of deter‐
gent, the amount of crockery and how
dirty it is.
When a programme is selected for the
first time, the display shows an average
time for a cold water intake.
The times shown in the Programme
chart refer to standard test loads and
temperatures.
Each time a programme is run, the
electronic unit takes the new conditions
into account, and calculates the time
required.
51
Operation
Energy management
Programme finished
To save energy, the dishwasher will
switch off automatically 10 minutes af‐
ter the last time a button has been
pressed or 10 minutes after the end of
the programme (see "Programme op‐
tions - Optimise standby").
The programme has ended when .
appears in the display.
The drying fan may continue to run for
a few minutes at the end of the pro‐
gramme.
Press the button to switch the
The dishwasher can now be opened
and unloaded (see "Unloading the
dishwasher").
dishwasher back on.
The dishwasher will not switch off
whilst a programme is running, during
the Delay start period or if there is a
fault.
To prevent the risk of steam
damage to the worktop edging
above the dishwasher, it is advisable
to leave the door closed until you are
ready to unload the crockery. Alter‐
natively, you can open the door fully
until the crockery is cool enough to
unload. Do not leave the door only
partially open.
52
Operation
Switching off
Unloading the dishwasher
At the end of a programme:
Dishes tend to break and chip more
easily when they are hot. Allow the
dishes to cool until they are comforta‐
ble enough to handle before unloading
them.
The dishwasher can be switched off
at any time using the button.
Switching the dishwasher off during a
programme stops the programme.
If you open the door fully after switch‐
ing off, the dishes will cool much faster.
Switching the dishwasher off during the
run-up to a Delay start time (FlexiTimer)
will also stop the process.
First unload the lower basket, then the
upper basket and finally the cutlery tray
(depending on model).
This will prevent water drops from the
upper basket and cutlery tray from fall‐
ing onto the dishes in the lower basket.
If the dishwasher is not going to be
used for a longer period of time, e.g.
whilst on holiday, the tap should be
turned off.
53
Operation
Interrupting a programme
Changing a programme
A programme is interrupted as soon as
the door is opened.
If the door is closed again, the pro‐
gramme will continue from the point it
was at before the door was opened.
If the detergent dispenser flap has
already opened, do not change the
programme.
If a programme has already started and
you wish to change it, proceed as fol‐
lows:
Water in the dishwasher may be
hot. Danger of scalding!
Switch the dishwasher off with the
button.
Only open the door if absolutely nec‐
essary and exercise extreme caution
when doing so. Before closing the
door again, leave it ajar for approx.
20 seconds. This will enable the tem‐
perature in the wash cabinet to set‐
tle. Then raise the door up and push
until the catch engages.
Switch the dishwasher on again with
the button.
Select the programme you want, and
then start it.
54
Programme options
DetergentAgent
Short
For optimum cleaning results, the dish‐
washer automatically adjusts the pro‐
gramme sequence to the type of deter‐
gent being used. Depending on the
programme, this can mean that the run‐
ning time and energy consumption vary
slightly.
The Short option reduces the dura‐
tion of programmes in which this option
is available.
In order to achieve optimum cleaning
results, consumption rates are in‐
creased with this option.
When used in combination with the
Quick wash programme, the Short
option results in a wash programme
without drying or automatic opening of
the door (if available).
Switch the dishwasher on with the
button.
The Start indicator light will flash.
Select a programme.
Press the button.
The indicator light comes on.
The programme can now be started.
The option selected will remain active
for that particular programme until the
setting is changed.
55
Programme options
Press the button 9 times.
Switching off the refill indica‐
tors
The indicator light will flash rapidly 9
times at intervals.
If you only ever use multi-function com‐
bination products in your dishwasher,
you can switch the refill reminders for
salt and rinse aid off if you wish. Doing
so will not affect the DetergentAgent
function.
The flashing sequence in the display
will appear whether the refill indicators
are switched on or off.
– : Refill indicators are switched on.
– : Refill indicators are switched off.
Switch the dishwasher off with the
button if it is switched on.
Press the Start button to change the
setting.
Press the Start button in and, whilst
holding it in, switch the dishwasher
on using the button.
Keep the Start button pressed in for
at least four seconds until the Start
indicator light comes on.
The setting is now stored in memory.
Switch the dishwasher off with the
button.
If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to add
dishwasher salt and rinse aid and to
switch the refill indicators back on.
If this does not happen, start the proce‐
dure from the beginning again.
56
Programme options
Switch the dishwasher on with the
Delay start
button.
You can set the start time for a pro‐
gramme, e.g. to take advantage of night
time electricity tariffs. The start time
can be delayed between 30 minutes
and 24 hours.
The Start indicator light will flash.
Select the programme you want.
Press the button.
The delay period is shown in 30-minute
increments for a delay period between
30 minutes and 9 hours 30 minutes. It is
shown in hours for periods longer than
this.
The last Delay start time used will ap‐
pear in the display. The Delay start indi‐
cator light comes on.
Set the required time using the
button.
When using the Delay start function,
make sure that the detergent com‐
partment is dry before adding deter‐
gent. Wipe dry with a cloth if neces‐
sary. If the compartment is wet,
powder detergent can become lum‐
py and stick to the dispenser, with
the result that it is not fully dis‐
pensed.
If you keep the button pressed in,
the time will increase automatically up
to hours. To get back to . hours,
press the button twice.
Press the Start button.
The Start indicator light will come on.
Do not use liquid detergent when se‐
lecting Delay start, as it can run into
the dishwasher before it is required.
To prevent children coming into
contact with dishwasher detergent:
Add the detergent immediately be‐
fore starting the programme, i.e. be‐
fore activating Delay start with the
Start button. Then lock the door with
the safety lock.
57
Programme options
Starting a programme before the De‐
lay start period has elapsed:
If "Optimise standby" is switched on
(see "Programme options - Optimise
standby"), the display will go out after
a few minutes, leaving just the Start
indicator light flashing slowly.
A programme can be started before the
Delay start period has elapsed.
Proceed as follows:
Press any button to switch the display
back on again for a few minutes.
Switch the dishwasher off with the
button.
Switch the dishwasher on again with
the button.
The time up until the programme starts
will appear counting down in the dis‐
play in hours for durations above
10 hours, and in hours and minutes for
durations below this.
Select the programme you want.
Press the Start button.
The programme cycle will begin. The
Start indicator light will come on.
When the set time is reached, the pro‐
gramme selected will start automatical‐
ly. The time remaining will appear in the
display and the indicator light will go
out.
How the Delay start time is shown in
the display:
up to 59 minutes:
e.g. 30 minutes = .
1 hour up to 9 hours 30 minutes:
e.g. 5 hours = .
10 hours and over:
e.g. 15 hours =
58
Programme options
Press the button 5 times.
Adjust Sensor wash
You can adjust the Sensor wash pro‐
gramme so that it will remove stubborn
soiling in a lightly soiled load.
The indicator light will flash rapidly 5
times at intervals.
The flashing sequence in the display in‐
dicates whether "Adjust sensor wash"
is activated or not.
Switch the dishwasher off with the
button, if it is switched on.
– : "Adjust sensor wash" is switched
Press the Start button in and, whilst
holding it in, switch the dishwasher
on using the button.
Keep the Start button pressed in for
at least 4 seconds until the Start indi‐
cator light comes on.
on.
– : "Adjust sensor wash" is switch‐
ed off.
Press the Start button to change the
setting.
If this does not happen, start the proce‐
dure from the beginning again.
The setting is now stored in memory.
Switch the dishwasher off with the
button.
59
Programme options
Press the button 8 times.
Optimise standby
"Optimise standby" is activated by de‐
fault.
The indicator light will flash rapidly 8
times at intervals.
To save energy, the dishwasher will
switch off automatically a few minutes
after the last time a button has been
pressed or after the end of a pro‐
gramme.
The flashing sequence in the display
shows whether "Optimise standby" is
activated or not.
– : "Optimise standby" is switched
on.
The dishwasher will not switch off
whilst a programme is running, during
the Delay start period or if there is a
fault.
– : "Optimise standby" is switched
off.
Press the Start button to change the
setting.
"Optimise standby" can be switched off
if you prefer. If you do this, the duration
before the dishwasher switches off in‐
creases to 6 hours. Doing this will in‐
crease energy consumption.
The setting is now stored in memory.
Switch the dishwasher off with the
button.
Switch the dishwasher off with the
button if it is switched on.
Press the Start button in and, whilst
holding it in, switch the dishwasher
on using the button.
Keep the Start button pressed in for
at least four seconds until the Start
indicator light comes on.
If this does not happen, start the proce‐
dure from the beginning again.
60
Programme options
Press the button 19 times.
Factory default settings
If you have altered any settings from
the factory default, you can reset them
back to the factory default settings as
follows:
The indicator light will do 1 long
flash and 9 short flashes at intervals.
The flashing sequence in the display in‐
dicates whether a setting has been
changed from its factory default.
Switch the dishwasher off with the
button, if it is switched on.
– : All settings are set to factory de‐
Press the Start button in and, whilst
holding it in, switch the dishwasher
on using the button.
fault settings.
– : At least one setting has been
changed.
Keep the Start button pressed in for
at least 4 seconds until the Start indi‐ To reset the dishwasher to the factory
cator light comes on.
default settings, press the Start but‐
ton.
If this does not happen, start the proce‐
dure from the beginning again.
The setting is now stored in memory.
Switch the dishwasher off with the
button.
61
Programme chart
Programme
Pre-wash
Programme sequence
Main wash
Interim rinse
Final rinse
Drying
°C
48
°C
47
ECO 1)
X
X
X
Sensor wash
Variable programme sequence,
sensor-controlled adjustment according to amount of crockery and soiling
If
47-55
If
65
68
68
65
45
X
X
X
X
X
required
required
Light soiling
55°C
X
2X
X
55
X
X
X
X
Intensive
75°C
75
Sensor wash
gentle
44
Quick wash
40°C
40
1) This programme is the most efficient in terms of its combined energy and water con‐
sumption for cleaning normally soiled crockery.
62
Programme chart
Consumption 2)
Duration 2)
Electricity
Water
Litres
Cold water
kWh
Hot water
kWh
Cold water
Hot water
h:min
h:min
2:41
0.73 3) / 0.76 4)
0.40 3) / 0.44 4)
11.3 3) / 11.0 4)
6.5 5) -16.0 6)
2:34
0.85 5) -1.35 6)
0.65 5) -0.90 6)
1:30-2:50
1:25-2:40
1.25
1.60
1.05
0.65
0.85
1.10
0.60
0.25
14.0
15.0
13.5
11.0
2:03
2:58
1:57
0:46
1:51
2:44
1:46
0:35
2) In practice there may be variations to these figures due to variable conditions and data
recorded by the sensors. The durations displayed in your dishwasher will reflect your
household conditions.
Selecting programme options will also affect consumption levels and programme dura‐
tions (see "Programme options").
3) Standard height dishwashers
4) XXL dishwashers
5) Part load with light soiling
6) Full load with heavy soiling
63
Programme chart
Crockery
Food deposits
Action required
Variable, sensor-controlled
programme sequence
Mixed,
everyday crockery
All fresh to dried-on
food deposits
Shorter duration
This needs a short programme
Shorter duration
Heat-sensitive glasses and
plastic
Fresh, easily removed food
deposits
This needs a gentle
programme with glass care
Shorter duration
Mixed crockery
This needs a water and energy
saving programme
Fresh food deposits which
have begun to dry on
Average programme values
Shorter duration
Pots, pans, everyday porcelain
and cutlery
Maximum cleaning power
Shorter duration
Burnt-on, stubborn, dried-
on food deposits containing
starch or protein 1)
1) Food such as potatoes, pasta, rice or stews can leave starchy deposits. Deposits containing protein
can be left by food such as fried meat, fish or eggs and bakes.
64
Programme chart
Programme
Detergent
2)
2)
Compartment I
Compartment II
25 ml
or
Sensor wash
-
1 tab
+short
20 ml
or
Quick wash 40°C
-
1 tab 3)
+short
20 ml
or
Sensor wash gentle
-
1 tab
+short
25 ml
or
1 tab
-
-
ECO
25 ml
or
Light soiling 55°C
1 tab
+short
25 ml
or
Intensive 75°C
10 ml
1 tab
+short
2) see "Detergent"
3) In some cases, tabs may not dissolve completely.
65
Cleaning and care
Cleaning the door and the door
seal
Mould could build up on the door seal
and the sides of the dishwasher door
as these surfaces are outside the wash
cabinet and are not accessed and
cleaned by the spray arm jets.
Check your dishwasher regularly (ap‐
prox. every 4-6 months). This way
faults and problems can be avoided.
The external surfaces of this ap‐
pliance are all susceptible to
scratching.
Contact with unsuitable cleaning
agents can alter or discolour the ex‐
ternal surfaces.
Wipe the door seals regularly with a
damp cloth to remove food deposits.
Wipe off any food or drink residues
which may have dripped onto the
sides of the dishwasher door before
closing it.
Cleaning the wash cabinet
The wash cabinet is largely self-clean‐
ing, provided that the correct amount of
detergent is always used.
If, however, there are limescale or
grease deposits in the cabinet, these
can be removed with a special dish‐
washer cleaner (see "Optional accesso‐
ries"). Follow the instructions on the
packaging.
Using mainly low temperature pro‐
grammes (below 50°C), could cause
bacteria and unpleasant odours to build
up in the wash cabinet. To avoid this,
the dishwasher will increase the tem‐
perature in the final rinse of the selected
programme automatically after several
programmes using low temperatures
have been run.
Clean the filters in the wash cabinet
regularly.
66
Cleaning and care
To avoid damaging external surfaces,
do not use:
Cleaning the door front
Soiling that is left too long might
become impossible to remove and
could cause external surfaces to al‐
ter or discolour.
– cleaning agents containing soda,
ammonia, acids or chlorides,
– cleaning agents containing descaling
agents,
Remove any soiling immediately.
– abrasive cleaning agents, e.g. pow‐
der cleaners and cream cleaners,
Clean the front with a solution of
warm water and a little washing-up
liquid applied with a soft sponge.
Wipe the surfaces dry using a soft
cloth.
For cleaning, you can also use a
clean, damp microfibre cloth, such as
the Original Miele all purpose microfi‐
bre cloth, without any cleaning agent.
– solvent-based cleaning agents,
– stainless steel cleaning agents,
– dishwasher cleaner,
– oven cleaner,
– glass cleaning agents,
– hard, abrasive brushes or sponges,
e.g. pot scourers, brushes or spong‐
es which have been previously used
with abrasive cleaning agents,
– dirt erasers,
– sharp metal scrapers,
– steel wool or metal scourers,
– steam cleaning appliances.
67
Cleaning and care
Checking the filters in the
wash cabinet
Cleaning the filters
Switch the dishwasher off.
The filter combination in the base of the
wash cabinet retains coarse soil from
the suds solution, preventing it access‐
ing the circulation system and re-enter‐
ing the cabinet through the spray arms.
This dishwasher must not be
used without all the filters in place.
Collection of coarse soil may cause the
filters to clog. The level of soiling and
time it takes before the filters need
cleaning will vary depending on use.
Check the condition of the filters reg‐
ularly and clean them if necessary.
Turn the handle anti-clockwise to re‐
lease the filter combination .
Lift the filter combination out of the
dishwasher . Remove any coarse
particles and rinse the filter well un‐
der running water.
Use a nylon brush if necessary.
During cleaning ensure that
course soil doesn't get into the cir‐
culation system and cause a block‐
age.
68
Cleaning and care
Replace the filter combination so that
it lies flat in the base of the wash
cabinet.
To clean the inside of the filter, the flap
must be opened:
Press the catches together in the
direction of the arrows as shown, and
open the filter .
Then turn the handle clockwise until
both arrows point towards each oth‐
er. This will lock the filter combination
in place.
Rinse all the filters under running wa‐
ter.
Take care when you are fitting
the filter combination that it is se‐
cured in position correctly.
Otherwise coarse soil could get into
the circulation system and cause a
blockage.
Then close the flap so that the catch
engages.
69
Cleaning and care
Cleaning the spray arms
Particles of food can get stuck in the
spray arm jets and bearings. The spray
arms should therefore be inspected and
cleaned regularly (approx. every 4 - 6
months).
Switch the dishwasher off.
Remove the spray arms as follows:
Take out the cutlery tray (if your dish‐
washer is fitted with one).
Push the top spray arm upwards to
engage the inner ratchet. Then un‐
screw the spray arm.
Pull the lower spray arm firmly up‐
wards to remove it.
Push the middle spray arm upwards
to engage the ratchet. Then un‐
screw the spray arm .
Use a pointed object to push food
particles into the spray arm jets.
Rinse thoroughly under running wa‐
ter.
Remove the lower basket.
Refit the spray arms and check that
they rotate freely.
70
Problem solving guide
With the help of the following guide, minor faults in the performance of the appli‐
ance, some of which may result from incorrect operation, can be put right without
contacting Miele. This will save time and money.
Please note that a call-out charge will be applied to unnecessary service visits
where the problem could have been rectified as described in these operating in‐
structions.
Unauthorised or incorrect repairs could cause personal injury or damage to
the appliance.
Repair work to electrical appliances must only be carried out by a suitably
qualified and competent person in strict accordance with current local and na‐
tional safety regulations. The manufacturer cannot be held liable for unauthor‐
ised work.
Technical problems
Problem
Possible cause and remedy
The Start indicator light The appliance is not plugged in.
does not flash after the
dishwasher has been
switched on using the
button.
Insert the plug and switch on at the socket.
The mains fuse has tripped.
Reset or replace the fuse (see data plate for mini‐
mum fuse rating).
The dishwasher stops
during a programme.
The mains fuse has tripped.
Reset or replace the fuse (see data plate for mini‐
mum fuse rating).
If the mains fuse trips again, call Miele.
71
Problem solving guide
Problem
Possible cause and remedy
The Inlet/Drain and
Rinse aid indicator
lights are flashing at the
same time.
Fault number ap‐
pears in the display.
There may be a technical fault.
Switch the dishwasher off with the button.
Switch the dishwasher back on after a few sec‐
onds.
Select the programme you want to use.
Press the Start button.
If the indicator lights flash again, there is a technical
fault.
Call Miele.
Fault :
The Waterproof system has reacted.
Turn off the tap.
Call Miele.
The drain pump is still
running, even with the
door open.
Fault :
A fault has occurred in the circulation pump.
Switch the dishwasher off for at least 30 seconds
using the button.
Switch the dishwasher back on.
If the fault message appears again, there is a techni‐
cal fault.
Call Miele.
72
Problem solving guide
Water inlet fault
Problem
Possible cause and remedy
The Inlet/Drain indica‐ The tap is turned off.
tor light flashes.
Turn on the tap fully.
The dishwasher stops
during a programme.
The Inlet/Drain indica‐
tor light flashes.
Fault code or ap‐
pears in the display.
Before rectifying the problem, you must:
Switch the dishwasher off with the button.
Water intake is restricted.
Turn on the tap fully and start the programme
again.
Clean the water inlet filter (see "Maintenance").
The water pressure at the intake is lower than 30
kPa (0.3 bar).
Seek professional advice.
Water drainage fault
Problem
Possible cause and remedy
The dishwasher stops
during a programme.
The Inlet/Drain indica‐
tor light flashes.
Fault code appears
in the display.
Before rectifying the problem you must:
Switch the dishwasher off with the button.
The water outlet is restricted.
There might be water in the wash cabinet.
Clean the filter combination (see "Cleaning and
care - Cleaning the filters").
Clean the drain pump (see "Maintenance").
Clean the non-return valve (see "Maintenance").
Remove any kink or loop in the drain hose.
73
Problem solving guide
General problems
Problem
Possible cause and remedy
The indicator lights and The dishwasher has switched off automatically to
display are dark.
save energy.
Switch the dishwasher on again with the but‐
ton.
Detergent residue is left The dispenser was still damp when detergent was
in the dispenser at the
end of a programme.
added.
Make sure the dispenser is dry before adding de‐
tergent.
The detergent dispens‐ Clogged detergent residue is blocking the catch.
er lid cannot be closed
properly.
Clean the detergent from the catch.
At the end of a pro‐
gramme there is a film
of moisture on the in‐
side of the door and the
interior walls.
This is caused by the drying system and does not in‐
dicate a fault. The moisture will dissipate after a
while.
Water remains in the
wash cabinet at the end
of a programme.
Before rectifying the problem you must:
Switch the dishwasher off with the button.
The filter combination in the wash cabinet is clogged.
Clean the filter combination (see "Cleaning and
care - Cleaning the filters").
The drain pump or non-return valve may be blocked.
Clean the drain pump or the non-return valve (see
"Maintenance").
The drain hose is kinked.
Remove any kink from the drain hose.
74
Problem solving guide
Noises
Problem
Possible cause and remedy
Knocking noise in the
wash cabinet.
A spray arm is knocking against an item in a basket.
Interrupt the programme, and rearrange the items
which are obstructing the spray arm.
Rattling noise in the
wash cabinet.
Items of crockery are insecure in the wash cabinet.
Interrupt the programme, and rearrange the items
of crockery.
A foreign object (e.g. a cherry stone) has become
lodged in the drain pump.
Remove the foreign object from the drain pump
(see "Maintenance - Cleaning the drain pump and
non-return valve").
Knocking noise in the
water pipes.
This may be caused by the on-site installation or the
cross-section of the piping.
This has no influence on dishwasher function. If in
doubt, contact a suitably qualified plumber.
75
Problem solving guide
Unsatisfactory washing result
Problem
Possible cause and remedy
The dishes are not
clean.
The dishes were not loaded correctly.
See notes in "Loading the dishwasher".
The programme was not powerful enough.
Select a more intensive programme (see "Pro‐
gramme chart").
There is some stubborn soiling although most of the
crockery is only lightly soiled (e.g. with tea stains).
Select the "Adjust Sensor wash" programme op‐
tion (see "Programme options").
Not enough detergent was dispensed.
Use more detergent, or change your detergent.
Items are blocking the path of the spray arms.
Rearrange the items so that the spray arms can
rotate freely.
The filter combination in the base of the wash cabinet
is not clean or is not correctly fitted.
This may cause the spray arm jets to get blocked.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets, if necessary (see "Clean‐
ing and care - Cleaning the spray arms").
The non-return valve is open and blocked. Dirty water
has flowed back into the wash cabinet.
Clean the drain pump and the non-return valve
(see "Maintenance").
Smearing appears on
glassware and cutlery,
there is a bluish sheen
on the surface of glass‐
ware; film can be wiped
off.
The rinse aid dosage is set too high.
Reduce the dosage (see "Before using for the first
time - Rinse aid").
76
Problem solving guide
Problem
Possible cause and remedy
Dishes, cutlery and
glasses are not dry or
are flecked.
The amount of rinse aid may be insufficient, or the
rinse aid reservoir is empty.
Replenish the reservoir, increase the dosage or
change the brand of rinse aid (see "Before using
for the first time - Rinse aid").
Crockery was taken out of the cabinet too soon.
Leave it in for longer (see "Operation").
Combination tabs have been used which have im‐
paired drying performance.
Change your detergent, or replenish the rinse aid
(see "Before using for the first time - Rinse aid").
Glassware has a brown This may be caused by the detergent.
or blue tinge, and film
cannot be wiped off.
Change your detergent.
Glassware is dull and
The glassware is not dishwasher-proof. The surfaces
discoloured; film cannot are affected.
be wiped off.
There is no remedy.
Purchase glassware which is dishwasher-proof.
Tea or lipstick stains
have not been com‐
pletely removed.
The wash temperature of the selected programme
was too low.
Select a programme with a higher wash tempera‐
ture.
The bleaching effect of the detergent used is too low.
Change your detergent.
Plastic items are discol‐ Natural dyes e.g. from carrots, tomatoes or tomato
oured.
sauce may be the cause. The amount of detergent
used or its bleaching effect was not sufficient to deal
with natural dyes.
Use more detergent (see "Operation - Detergent").
Discolouration is irreversible.
77
Problem solving guide
Problem
Possible cause and remedy
White residue is visible Not enough rinse aid was used.
on cutlery and crock‐
ery, clouding occurs on
glassware; film can be
wiped off.
Increase the dosage (see "Before using for the first
time - Rinse aid").
There is no dishwasher salt in the salt reservoir.
Fill the salt reservoir (see "Before using for the first
time - Dishwasher salt").
The salt reservoir cap has not been screwed on cor‐
rectly.
Replace it, making sure that it screws back on
correctly.
An unsuitable combination detergent has been used.
Change your detergent. Use a standard liquid,
tablet or powder detergent, and fill the salt and
rinse aid reservoirs in the dishwasher.
The water softener is programmed to too low a water
hardness level.
Programme the water softener for harder water
(see "Before using for the first time - Water soften‐
er").
There are rust stains on The affected items are not corrosion resistant.
cutlery.
There is no remedy.
Purchase cutlery which is dishwasher-proof.
A programme was not run after dishwasher salt was
added. Traces of salt have got into the wash cycle.
Always run the Quick wash programme with the
Short programme option selected and without any
crockery in the dishwasher after adding dishwash‐
er salt.
The salt reservoir cap has not been screwed on cor‐
rectly.
Replace it, making sure that it screws back on
correctly.
78
Maintenance
Cleaning the water inlet filter
A filter is incorporated in the screw con‐
nection of the valve on the water inlet
hose. The filter must be cleaned when
dirty, otherwise insufficient water flows
into the wash cabinet.
The plastic housing of the water
connection contains an electrical
component.
The housing must not be dipped in
water.
Recommendation
Carefully remove the washer.
If the mains water contains a large
amount of insoluble substances, we
recommend fitting a large-area filter in
the connection between the tap and the
water inlet hose threaded union. This
filter is available from Miele.
Withdraw the filter using pointed pli‐
ers and rinse clean under running
water.
Replace the filter and washer, making
sure they are sitting correctly.
Reconnect the inlet hose to the tap,
making sure it goes on correctly and
is not cross-threaded.
Cleaning the filter:
Disconnect the dishwasher from the
mains supply.
Switch off at the mains socket and
withdraw the plug.
Turn on the tap.
If water leaks out, the inlet hose may
not be connected securely or it may
have been screwed on at an angle.
Turn off the tap.
Unscrew the inlet hose.
Unscrew and reconnect the inlet
hose correctly.
79
Maintenance
Cleaning the drain pump and
non-return valve
If the water has not been pumped away
at the end of a programme, the drain
pump or the non-return valve might be
blocked. They are, however, easy to
clean.
Disconnect the dishwasher from the
mains supply. Switch off at the mains
socket and withdraw the plug.
Take the filter combination out of the
wash cabinet (see "Cleaning and care
- Cleaning the filters").
The drain pump is situated under the
non-return valve (see arrow).
Scoop the water out of the cabinet
using a suitable container or utensil.
Remove all foreign objects from the
drain pump (watch out for glass or
bone splinters which are particularly
difficult to detect and could cause in‐
jury). Turn the drain pump impeller by
hand to check that there are no more
obstructions. You will feel a little re‐
sistance when you turn the impeller.
Carefully refit the non-return valve
and secure it with the catch.
Ensure that the catch engages
correctly.
Be careful not to damage any
delicate components when cleaning
the drain pump and the non-return
valve.
Press the catch for the non-return
valve inwards .
Lift out the non-return valve , and
rinse well under running water.
Remove all foreign objects from the
non-return valve.
80
After sales service
Repairs
Warranty
In the event of any faults which you
The manufacturer's warranty for this
cannot remedy yourself, please contact appliance is 2 years.
Miele.
For further information, please refer to
your warranty booklet.
The contact details for Miele are giv‐
en at the back of these instructions.
When contacting Miele, please quote
the model and serial number of your
dishwasher, both of which are shown
on the data plate on the right-hand side
of the door.
81
Optional accessories
Dishwasher detergent and rinse aid, as
well as cleaning and care products, are
available as optional accessories.
All the products are designed for use
with Miele dishwashers.
Detergent tabs
– sparkling results even with stubborn
food deposits
– combination product with other com‐
ponents such as rinse aid, salt and
glass protection additives
These and many other useful products
can be ordered via the internet at
country) or from Miele (see end of this
booklet for contact details).
– phosphate-free - safe for the environ‐
ment
– water-soluble wrapping - no need to
unwrap
Powder detergent
– with active oxygen for thorough
cleaning
Dishwasher detergent, rinse
aid and salt
– with enzymes which are effective
even in low temperature programmes
When you decided to buy a Miele dish‐
washer, you chose excellent quality and
performance. However, ensuring that
your dishwasher always delivers the
best possible results will also depend
on your choice of dishwasher deter‐
gent, rinse aid and dishwasher salt, as
cleaning results can vary depending on
the brand used.
With Miele CareCollection products,
you can be sure of optimum results as
these products have been specially de‐
signed for Miele dishwashers.
– with glass protection against corro‐
sion
Rinse aid
– for gleaming glasses
– helps crockery to dry
– with glass protection against corro‐
sion
– specially designed cap for precise,
easy dispensing
Dishwasher salt
– prevents limescale on crockery and
in the appliance
– extra coarse-grained
82
Optional accessories
Dishwasher care products
Accessories
Miele cleaning and care products pro‐
Some accessories may be supplied as
vide optimum care for your dishwasher. standard, depending on model.
Dishwasher cleaner Cappuccinatore insert
– cleans the dishwasher effectively and The Cappuccinatore insert can be used
thoroughly
for cleaning the individual parts of the
Miele Cappuccinatore in the dishwash‐
er.
– removes grease, bacteria and un‐
pleasant odours
Cutlery basket
– ensures excellent dishwashing re‐
sults
The cutlery basket is placed in the low‐
er basket and can be used to wash ad‐
ditional items of cutlery.
Dishwasher descaler
– removes heavy limescale deposits
Glass rail
– mild and gentle with natural citric
acid
This rail is designed to hold glasses
with stems securely in the lower basket.
Dishwasher conditioner
– removes odours, limescale and light
deposits
– maintains the elasticity and leak
tightness of the seals
83
Electrical connection
This dishwasher is supplied with a
mains cable with moulded plug ready
for connection to an AC single phase
supply, (230 - 240 V 50 Hz for NZ and
Australia) via a suitable switched sock‐
et.
Before connecting the appliance,
check that the connection data on
the data plate (voltage, frequency,
rated load and fuse rating) matches
the mains electricity supply. If in any
doubt, consult a qualified electrician.
The electrical socket must be
easily accessible after the dishwash‐
er has been installed. Do not con‐
nect the dishwasher to the mains
electricity supply by an extension
lead. Extension leads do not guaran‐
tee the required safety of the appli‐
ance (e.g. danger of overheating).
The data plate is located on the right-
hand side of the door.
All electrical work must be car‐
ried out by a suitably qualified and
competent person in strict accord‐
ance with current local and national
safety regulations.
Do not connect the appliance solely to
an inverter such as those used with an
autonomous energy source e.g. solar
power. When switched on, peak loads
in the system can cause the safety
switch-off mechanism to be triggered.
This can damage the electronic unit.
The machine must not be used with so-
called energy-saving devices either.
These reduce the amount of energy
supplied to the machine, causing it to
overheat.
For extra safety, it is advisable to in‐
stall a residual current device (RCD),
with a trip current of 30 mA.
84
Water connection
– The water pressure (flow pressure at
the take-off point) must be between
30 and 1000 kPa (0.3 and 10 bar). If
the water pressure is too high, a
pressure reducer valve must be fit‐
ted.
The Miele Waterproof system
As long as your dishwasher has been
installed correctly, the Miele waterproof
anti-leak system will protect you from
water damage.
Connection to the water sup‐
ply
After connecting the dishwasher to
the water supply, check that all
plumbing connections are watertight.
Water in the dishwasher must
not be used as drinking water.
To avoid any damage to the ap‐
pliance, the dishwasher must only be
operated when it is connected to a
fully vented plumbing system.
– The dishwasher may be connected to
a cold or hot water supply, max.
60°C.
We would only recommend connec‐
tion to a hot water supply if it is eco‐
nomical, e.g. a solar powered supply.
When connected to a hot water sup‐
ply, all programmes will be carried
out with hot water.
– The inlet hose is approx. 1.5 m long.
– A tap with a 3/4" male thread must
be provided on site.
– Connection to the mains water sup‐
ply should only be carried out by a
qualified and competent person in
strict accordance with national and
local safety regulations. The tap
should be easily accessible once the
appliance has been installed.
The inlet hose must not be
shortened or damaged in any way as
it contains electrical components
(see illustration).
– IMPORTANT
Australia and New Zealand
This appliance must be installed ac‐
cording to AS/NZS 3500.1. Back flow
prevention is already integrated in the
appliance.
85
Water connection
Venting the drainage system
Drainage
If the on-site drain connection is situ‐
ated lower than the guide path for the
bottom basket rollers in the open door,
the drainage system must be vented.
Otherwise a siphoning effect during a
programme can cause the appliance to
empty itself of water.
– The appliance drainage system is fit‐
ted with a non-return valve which
prevents dirty water from flowing
back into the dishwasher via the
drain hose.
– The dishwasher is supplied with ap‐
prox. 1.5 m of flexible drain hose with
an internal diameter of 22 mm.
To vent it: Open the dishwasher door
fully.
– The drain hose can be extended us‐
ing a connection piece to attach a
further length of hose. The drainage
length must not be longer than 4 m,
and the delivery head must not ex‐
ceed 1 m.
– If the hose is to be directly fitted to
the drainage outlet on site, use the
hose clip supplied (see installation di‐
agram).
– The hose can be directed to the left
or the right of the appliance.
– The on-site connector for the drain
hose can be adapted to different
widths of hose. If the connector pro‐
trudes too far into the drain hose, it
will need to be shortened. Otherwise
the drain hose may become blocked.
Pull the lower spray arm firmly up‐
wards to remove it.
Cut off the top of the vent valve in the
wash cabinet.
– The drain hose must not be short‐
ened.
Make sure that there are no
kinks in the hose, and that it is not
squashed or stretched.
After commissioning the appliance,
ensure that the water outlet does not
leak.
86
Technical data
Dishwasher model
Standard
XXL
Height freestanding model
84.5 cm (adjustable +
3.5 cm)
-
Height built-in model
80.5 cm (adjustable
+ 6.5 cm)
84.5 cm (adjustable
+ 6.5 cm)
Height of building-in recess
Min. 80.5 cm (+ 6.5
cm)
Min. 84.5 cm (+ 6.5
cm)
Width
59.8 cm
60 cm
59.8 cm
60 cm
-
Width of building-in recess
Depth freestanding model
Depth built-in model
Weight
60 cm
57 cm
57 cm
Max. 56 kg
Max. 64 kg
Voltage
See data plate
Rated load
See data plate
See data plate
0.10 W
Fuse rating
Power consumption when
switched off
0.10 W
Power consumption when not 2.00 W
switched off
2.00 W
Test certificates awarded
See data plate
Water pressure (flow rate)
30 - 1000 kPa
30 - 1000 kPa
(0.3 - 10 bar)
Up to max. 60 °C
Max. 1 m
(0.3 - 10 bar)
Up to max. 60 °C
Max. 1 m
Hot water connection
Delivery head
Drainage length
Mains cable
Max. 4 m
Max. 4 m
Approx. 1.7 m
14 place settings*
Approx. 1.7 m
14/15 place settings*
Capacity
* Depending on model
87
Miele Australia Pty. Ltd.
ACN 005 635 398
ABN 96 005 635 398
Miele Center and Head Office Melbourne:
1 Gilbert Park Drive
Knoxfield, VIC 3180
Miele Center and Office Melbourne:
206-210 Coventry Street
South Melbourne, VIC 3205
Miele Center and Office Sydney:
3 Skyline Place
Frenchs Forest, NSW 2086
Miele New Zealand Limited
IRD 98 463 631
Miele Center and Office Brisbane:
39 Harvey Street North
Eagle Farm, QLD 4009
Head Office:
Level 2, 10 College Hill
Freemans Bay, Auckland 1011
Miele Center and Office Adelaide:
83-85 Sir Donald Bradman Drive
Hilton, SA 5033
Miele Center Auckland:
8 College Hill
Freemans Bay, Auckland 1011
Miele Center and Office Perth:
205-207 Stirling Highway
Claremont, WA 6010
Telephone:
0800 4 MIELE (0800 464 353)
Miele Global Headquarters
Germany
Miele & Cie. KG
Carl-Miele-Straße 29
33332 Gütersloh
Federal Republic of Germany
88
G 6100 / G 6105
en-AU, NZ
M.-Nr. 09 867 820 / 03
|
