CV610-U2
CV610-UB
Silver/Black
All Black
Full HD USB 2.0 PTZ Camera
Operating Instructions
Version V3.6
CV610-U2 / CV610-UB Operation Manual
Accessories
IMPORTANT SAFETY INSTRUCTIONS:
•
•
Remove lens cover before plugging camera into power source.
Before starting operation, please fully read and follow all instructions in the manual. For your
safety, always keep this manual with the camera for reference.
Table of Contents
•
•
•
The camera power input range is 100-240VAC (50-60Hz), ensure the power supply input within this range
before powering on.
The camera power voltage is 12VDC, rated currency is 1.5A. We suggest you use it with the
original power supply adapter supplied in the box.
SAFETY GUIDELINES .................................................................................... 3
ACCESSORIES .............................................................................................. 3
QUICK START ................................................................................................ 4
PRODUCT HIGHLIGHTS................................................................................ 5
RESOLUTION & FRAME RATE SETTINGS .................................................... 5
CAMERA SPECS............................................................................................ 5
CAMERA INTERFACE .................................................................................... 6
Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the
connectors from moisture and dirt.
• Operational environment: 32ºF to 122ºF ( 0ºC to 50ºC) and humidity less than 90%. To avoid any danger, do
not put anything inside the camera, and keep away from corrosive liquids.
• Avoid stress, vibration and jolts during transportation, storage and installation.
• Do not detach the camera housing and cover. For any service, please contact authorized technicians.
• RF cable and control cable should be individually shielded, and cannot be substituted with other cables. Do
not direct the camera lens towards strong light, such as the sun or the intensive light.
• Always use a dry, soft cloth to clean the camera housing. Only use neutral cleaning agents when there is need
to clean smudges or dirt from camera body. To avoid damage on the camera lens, only use a soft microfiber
cloth.
CAMERA DIMENSIONS
6
.................................................................................
IR REMOTE CONTROLLER............................................................................ 7
OSD MENU .................................................................................................... 8
VISCA IN (RS232) PORT ................................................................................ 10
VISCA PROTOCOL ........................................................................................ 10
IR TRANSFER (IR PASS) ................................................................................ 17
UVC CONTROL.............................................................................................. 17
WALL MOUNT INSTALLATION....................................................................... 18
• Do not carry or move the camera by holding the camera head. To avoid mechanical damage of internal gears,
do not rotate the camera head by hand.
• Put the camera on a fixed desk or platform, avoid installing on surfaces that are not level.
• Power Supply Polarity (Drawing) below:
INCLUDED IN THE BOX
1. Power Adapter
2. CV610-U2-WM - Wall Mount
3. Power Cable
4. RS232 Control Cable
5. USB2.0 Cable
6. Remote Controller (battery not included)
7. Main Camera
2
3
CV610-U2 / CV610-UB Operation Manual
CV610-U2 / CV610-UB Specifications
QUICK START
PRODUCT HIGHLIGHTS
•
Compact, ergonomically designed housing perfect for small huddle rooms or locations
1. REMOVE Lens Cover and check all cable connections to be sure they are all firmly
connected before powering on
•
Supports advanced Ambarella DSP, 1/2.8 inch 5MP image sensor, and high quality 10X 62.5 degree
FOV optical lens, provides crystal clear image quality
•
•
•
•
•
•
•
•
•
Fast switching between different video formats: less than 1 second
10X Optical Zoom + 12X Digital Zoom
Fast and accurate focus performance
Easy firmware upgrade - (field-upgradable)
USB2.0 high speed output
Effective RS232/485 serial control. Up to 128 presets
Compatible with the majority of videoconferencing software (UVC1.5 protocol standard)
Camera comes with accurate IR Remote Control unit
IR transfer/IR pass function: excepts signals from other codec’s and IR remote control signals
CV610-U2 SPECIFICATIONS
Video Format
Video Port
Sensor
MJPG - 1080P30, 720P30, 640*480P30
USB2.0
1/2.8 inch high quality 5MP CMOS sensor
Lens
F4.7~47.mm(10X), F1.8 – 14, Field of view: 62.5°(wide)-6.43°(tele)
Pan/tilt Rotation
Pan/tilt Speed
Preset
Pan:±170°; Tilt:-30°~+90°, support up-side down installation
2. Dial Switch Setting (at the bottom of the camera):
Pan: 0.1°-120°/s; Tilt: 0.1°-80°/s
10 via IR remote setting, 128 via VISCA control, preset accuracy :0.1°
DIP Switch (ARM)
Control Port
Min. Lux
White Balance
Focus
RS232, RS485, USB2.0
0.01lux
SW-1
OFF
ON
SW-2 Instruction
1
2
3
4
OFF
OFF
ON
Updating mode
Auto/Manual
Auto/Manual
Auto/Manual
Auto/Manual
Supported
Debugging mode
Iris
OFF
ON
Shutter
ON
Working mode
WDR
DIP Switch (IR CODE TYPE)
SW-3 SW-4 Instruction
BLC
Supported
2D Noise Reduction Supported
3D Noise Reduction Supported
1
2
3
4
OFF
ON
OFF
OFF
ON
Off(Close IR receiver)
Input Voltage
Dimension
Net weight
DC12V
148mm×132mm×161mm
0.9KG (2LBS)
OFF
ON
SEJIN 4PPM CODE
NEC CODE(standard)
ON
DIP Switch (USB)
SW-6 Instruction
OFF
RESOLUTION & FRAME RATE SETTINGS
SW-5
OFF
ON
1
2
3
4
The Marshall CV610-U2 acts as a UVC command slave to Teleconference, U.C. or Video Capture Software programs
that use it as a USB capture device. Once selected as an available camera, these software platforms send commands
to camera as to compatible resolutions and frame rates based on bandwidth, software parameters, and/or computer
capabilities. Some software platforms allow for direct adjust commands to change resolution and frame-rates, such
as VLC Player and others. CV610-U2 adjusts as commanded by software platform or to nearest resolution settings
available (1080p, 720p, 480p). There is no way to manually adjust resolutions and frame-rates from camera or camera
OSD menu, since it relies on UVC (USB video class) commands. CV610-U2 adheres to UVC1.5 protocol standards.
OFF
ON
Working mode
Updating mode
OFF
ON
ON
Note: Normal Working Mode: SW-1~5: ON, SW-6: OFF
4
5
CV610-U2 / CV610-UB Operation Manual
IR Remote Controller
CAMERA INTERFACE
IR REMOTE CONTROLLER
CAM 1
CAM 2
CAM 3
CAM 1
CAM 2
CAM 3
FOCUS
LED Function Instruction
Press any button and shows in red color: Current selection is to control CAM1;
Press any button and shows in green color: Current selection is to control CAM2;
Press any button and shows in blue color: Current selection is to control CAM3;
H
O
ME
CAM1/CAM2/CAM3:
Long press(3seconds) to set camera address;
ZOOM
MENU
Short press to select camera address to control.
1. Camera Lens
2. Camera Base
3. IR Receiver Panel
4. Indicator Light
Focus: +/-
Manual focus, only valid under manual focus mode;
Zoom: +/-
5. Dial Switch
6. Tripod Screw Hole
7. Installation Hole
8. RS232 (VISCA IN) Port
9. USB2.0 Port
10. DC12V Power Input
11. Power Indicator light (red)
Control the lens zoom rate;
CLEAR
PRESET
Navigate : Up/Down/Left/Right
In normal working mode, use navigate key to control pan/tilt；
Or enter OSD menu, use navigate key to set parameters.
Confirm/Home button:
In normal working mode, short press to let the camera go back to
home position
CAMERA DIMENSIONS (mm)
Menu Button: Enter the OSD menu
MENU
Number buttons
Set Preset: Long press(3seconds) the number button to save preset;
Clear Preset: +number button to clear the relative preset;
Long press(3seconds) the Clear button to clear all preset;
Short press 3 times to reset the lens focus;
Run Preset: Short press the number button to run the relative preset.
CLEAR
PRESET
Short press to power on or off the camera
6
7
CV610-U2 / CV610-UB Operation Manual
IR Remote Controller / OSD menu
EXP MODE
SHUT TIME
AUTO/MANUAL/IRIS/SHUT/BRI.
CV610-U2 OSD MENU EXPLAINED
Shutter time: 1/1~1/10K
(Valid when EXP MODE set to MANUAL or SHUT)
1
Iris value: 0-13
(Valid when EXP MODE set to MANUAL or IRIS)
IRIS
Gain value: 0dB~15dB
(Valid when EXP MODE set to MANUAL)
AGC
1. Once camera is powered up and working, press the Menu button
EXPOSURE
MENU
on the IR remote control to enter the OSD menu (see
BRIGHT
Brightness value: 0-27 (Valid when EXP MODE set to BRI.)
pic.1); once changes are made press the OSD menu button
again to exit and save modi ed parameters.
SLOW SHUT OFF/ON
OFF/50HZ/60HZ
FLICK
(Valid when EXP MODE set to AUTO or IRIS)
RETURN
Back to the main menu
BRIGHTNESS 1-15
SHARPNESS 0-15
2
CONTRAST
0-15
2. Use the navigate buttons (up/down/left/right) to choose which
function to select. As picture 1 shows, once selection is made,
the selected option will change to gray background highlight.
Press the right navigate button to go to the sub menu (see pic.2).
SATURATION 0-14
PICTURE
MIRROR
PIC FLIP
FREEZE
DEFOG
Image 180 degree rotation left/right: OFF/ON
Image 180 degree rotation up/down: OFF/ON
OFF/ON
OFF/1-15
RETURN
Back to the main menu
2D NR
OFF/ON
3. In the sub menu, once again press the up/down navigate buttons to scroll and select, use left/right
navigate button to cycle through selection options parameters.
3D NR
OFF/AUTO/ 1-4
OFF/1-6
D_WDR
IMAGE
ENHANCE
GAMMA
BACKLIGHT
HIGHLIGHT
RETURN
0-4
4. Select the last option “RETURN” and press the left navigate button to get back to main menu or
previous menu.
OFF/ON
OFF/ON
Back to the main menu
MENU
5. Press OSD button
again to exit the menu.
MASK SWITCH ON/OFF
6. The following pages outline the Menu structure as it appears in OSD Menu:
COLOR
INDEX
WHITE/YELLOW/GRAY/GREEN/VIOLET/RED
1-8
INDEX SWITCH OFF/ON
PROTOCOL
ADDRESS
VISCA/PELCO-P/PELCO-D
1~7
ROW START
ROW END
LINE START
LINE END
0-1919
1-1920
0-1079
1-1079
MASK
BAUD RATE
PARITY BIT
STANDBY MODE
RETURN
2400,9600,115200
NONE
Camera Set
( ON / OFF )
Back to the main menu
RETURN
Back to the main menu
D/N MODE
DAY/NIGHT/AUTO
FOCUS MODE
SENSITIVITY
D_ZOOM
AUTO/MANUAL/PUSH
LOW/MID/HIGH
OFF/ON
DAY TO NIGHT 15-126
NIGHT TO DAY 5-190
SWITCH DELAY 1-60
D/N MODE
FOCUS
ZOOM SPEED
LENS INIT
0-7
OFF/5K/10K/15K/20K/EXE
GAIN LIMIT
RETURN
2-511
DIS ZOOM RATIO OFF/ON
Back to the main menu
RETURN
Back to the main menu
IMAGE VER.
IMAGE DATE
PC-V0.0.6 (change without notice)
16.10.20 (change without notice)
WB MODE
B_GAIN
ATWB/GAIN/TEMP./SOD./FL./AWB/IDR./ODR./PUSH
0~255 (Only Valid when WB MODE set to GAIN or TEMP.)
0~255 (Only Valid when WB MODE set to GAIN or TEMP.)
Back to the main menu
CONTROL VER. UC V0.1.4 (change without notice)
CONTROL DATE 17.01.07 (changes without notice)
WB MODE
R_GAIN
CAMERA
INFO
RETURN
BAUDRATE
PARITY BIT
RETURN
9600
NONE
Back to the main menu
8
9
CV610-U2 / CV610-UB Operation Manual
VISCA Protocol
4. All Button Sending Mode: long press (3seconds) the Menu+ number “3” button simultaneously, the remote will
enter all button sending mode.
Error Messages
5. Similar operation for the TV control mode learning.
Command Packet
Note
Returned when the command format is different or when a
command with illegal command parameters is accepted
Syntax Error
z0 60 02 FF
VISCA IN (RS232) PORT
Returned when a command cannot be executed due
to current conditions. For example, when commands
controlling the focus manually are received during auto
focus.
Command Not
Executable
z0 61 41 FF
No.
Function
DTR
1
2
3
4
5
6
7
8
DSR
TXD
GND
RXD
A
Part 2 - Camera Control Command
Command
Funnation
Broadcast
Broadcast
Command Packet
88 30 01 FF
Note
Address setting
I/F Clear
AddressSet
IF_Clear
IR OUT
B
88 01 00 01 FF
CAM_Power
On
8x 01 04 00 02 FF
8x 01 04 00 03 FF
8x 01 04 07 00 FF
8x 01 04 07 02 FF
8x 01 04 07 03 FF
8x 01 04 07 2p FF
8x 01 04 07 3p FF
Power ON/OFF
Off
Stop
VISCA IN &RS485 Connection
VISCA IN &DB9 Connection
Camera VISCA IN Windows DB-9
Camera VISCA IN
RS485
Tele(Standard)
Wide(Standard)
Tele(Variable)
Wide(Variable)
1
2
3
4
5
6
7
8
DTR
DSR
TXD
1
2
3
4
5
6
7
8
DTR
DSR
TXD
6
4
2
5
3
DSR
DTR
RXD
GND
TXD
CAM_Zoom
p = 0(low)~7(high)
GND
RXD
A(+)
GND
RXD
A(+)
pqrs: Zoom Position
(0(wide) ~0x4000(tele))
Direct
8x 01 04 47 0p 0q 0r 0s FF
TX+
TX-
Stop
8x 01 04 08 00 FF
8x 01 04 08 02 FF
8x 01 04 08 03 FF
IR OUT
B(-)
IR OUT
B(-)
Far(Standard)
Near(Standard)
Direct
CAM_Focus
8x 01 04 48 0p 0q 0r 0s FF pqrs: Focus Position
8x 01 04 18 01 FF
One Push AF
SERIAL PORT CONFIGURATION:
pqrs: Zoom Position
(0(wide)~ 0x4000(tele))
tuvw: Focus Position
8x 01 04 47 0p 0q 0r 0s
0t 0u 0v 0w FF
CAM_ZoomFocus
Direct
Parameter
Baud rate
Start Bit
Value
Parameter
Stop Bit
Value
1bit
2400/9600/115200
Auto
8x 01 04 35 00 FF
8x 01 04 35 01 FF
8x 01 04 35 02 FF
8x 01 04 35 03 FF
8x 01 04 35 05 FF
8x 01 04 35 06 FF
8x 01 04 35 07 FF
8x 01 04 35 08 FF
8x 01 04 03 00 FF
1 bit
8 bit
Verify Bit
None
Indoor
Date Bit
Outdoor
OnePush
Manual
CAM_WB
VISCA PROTOCOL
Outdoor Auto
Sodium Lamp Auto
Sodium Auto
Reset
Part 1 - Camera Return Command
Ack/Completion Message
Up
8x 01 04 03 02 FF
8x 01 04 03 03 FF
Manual Control of R Gain
CAM_RGain
Command Packet
z0 41 FF
z0 51 FF
Note
Down
ACK
Returned when the command is accepted.
Returned when the command has been executed.
Direct
8x 01 04 43 00 00 0p 0q FF pq: R Gain (0~0xFF)
Completion
10
11
CV610-U2 / CV610-UB Operation Manual
VISCA Protocol
Part 2 - Camera Control Command
Command
Funnation
Reset
Command Packet
8x 01 04 04 00 FF
Note
Command
CAM_3D
Noise Reduction
Funnation
Direct
Command Packet
8x 01 04 54 0p FF
Note
Manual Control of B Gain
0:OFF 1: AUTO 2~5: LEVEL
Up
8x 01 04 04 02 FF
CAM_Bgain
50HZ
81 01 04 23 01 FF
Down
Direct
Full Auto
Manual
Bright
Reset
Up
8x 01 04 04 03 FF
FLICK
8x 01 04 44 00 00 0p 0q FF
8x 01 04 39 00 FF
pq: B Gain (0-0xFF)
60HZ
81 01 04 23 02 FF
81 01 04 62 02 FF
81 01 04 62 03 FF
81 01 04 62 22 FF
81 01 04 62 23 FF
Automatic Exposure mode
Manual Control mode
Bright mode(Manual control)
Shutter Setting
Freeze On
Freeze On Immediately
CAM_AE
8x 01 04 39 03 FF
Freeze Off
Freeze Off Immediately
Freeze
8x 01 04 39 0D FF
8x 01 04 0A 00 FF
Preset Freeze On
Preset Freeze Off
Freeze On When Running Preset
Freeze Off When Running Preset
8x 01 04 0A 02 FF
Receive IR(remote commander)
CODE from VISCA
communication ON/OFF
CAM_Shutter
Transfer On
8x 01 06 1A 02 FF
Down
Direct
Reset
Up
8x 01 04 0A 03 FF
IR_Transfer
8x 01 04 4A 00 00 0p 0q FF
8x 01 04 0B 00 FF
8x 01 04 0B 02 FF
8x 01 04 0B 03 FF
8x 01 04 4B 00 00 0p 0q FF
8x 01 04 0C 00 FF
8x 01 04 0C 02 FF
8x 01 04 0C 03 FF
8x 01 04 0C 00 00 0p 0q FF
8x 01 04 0D 00 FF
8x 01 04 0D 02 FF
8x 01 04 0D 03 FF
8x 01 04 4D 00 00 0p 0q FF
8x 01 04 3D 02 FF
8x 01 04 3D 03 FF
8x 01 04 D3 0p FF
8x 01 04 33 02 FF
pq: Shutter Position (0~0x15)
Iris Setting
Transfer Off
Up
8x 01 06 1A 03 FF
8x 01 06 01 VV WW 03 01 FF
8x 01 06 01 VV WW 03 02 FF
8x 01 06 01 VV WW 01 03 FF
8x 01 06 01 VV WW 02 03 FF
8x 01 06 01 VV WW 01 01 FF
8x 01 06 01 VV WW 02 01 FF
8x 01 06 01 VV WW 01 02 FF
8x 01 06 01 VV WW 02 02 FF
8x 01 06 01 VV WW 03 03 FF
CAM_Iris
Down
Down
Direct
Reset
Up
Left
pq: Iris Position (0~ 0x11)
Gain Setting
Right
Upleft
VV: Pan speed 0x01 (low speed)
to 0x18 (high speed)
WW: Tilt speed 0x01 (low speed)
to 0x14 (high speed)
YYYY: Pan Position(TBD)
ZZZZ: Tilt Position(TBD)
CAM_Gain
CAM_Bright
Upright
DownLeft
DownRight
Stop
Down
Direct
Reset
Up
pq: Gain Positon (0~0x0E)
Bright Setting
Pan_tiltDrive
8x 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
AbsolutePosition
RelativePosition
Down
Direct
On
pq: Bright l Positon ()
WDR ON/OFF
8x 01 06 03 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
CAM_WDR
Off
Home
Reset
8x 01 06 04 FF
8x 01 06 05 FF
Direct
On
pq: WDR Position (1~0x06)
BackLight On
8x 01 06 07 00 0W
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
CAM_BackLight
Set
W:1 UpRight 0:DownLeft
YYYY: Pan Limit Position(TBD)
ZZZZ: Tilt Limit Position(TBD)
Off
8x 01 04 33 03 FF
BackLight Off
Pan-tiltLimitSet
8x 01 06 07 01 0W
07 0F 0F 0F 07 0F 0F 0F FF
Reset
Up
8x 01 04 02 00 FF
Clear
8x 01 04 02 02 FF
Aperture Control
CAM_Aperture
Down
Direct
Reset
Set
8x 01 04 02 03 FF
8x 01 04 42 00 00 0p 0q FF
8x 01 04 3F 00 0p FF
8x 01 04 3F 01 0p FF
8x 01 04 3F 02 0p FF
8x 01 04 61 02 FF
pq: Aperture Gain (0~0x04)
p: Memory Number (=0 to 127)
Corresponds to 0 to 9 on the
Remote Commander
Part 3 - Inquiry Command
CAM_Memory
Recall
On
Command
CAM_PowerIng
Command Packet
Return Packet
y0 50 02 FF
Note
On
CAM_LR_Reverse
Image Flip Horizontal ON/OFF
Image Flip Vertical ON/OFF
8x 09 04 00 FF
8x 09 04 47 FF
8x 09 04 38 FF
8x 09 04 48 FF
Off
8x 01 04 61 03 FF
y0 50 03 FF
Off(Standby)
pqrs: Zoom Position
Auto Focus
On
8x 01 04 66 02 FF
CAM_ZoomPosIng
CAM_FocusModeIng
CAM_FocusPosIng
y0 50 0p 0q 0r 0s FF
y0 50 02 FF
CAM_PictureFlip
CAM_ColorGain
Off
8x 01 04 66 03 FF
Direct
8x 01 04 49 00 00 00 0p FF
(0~0x0E)
y0 50 03 FF
Manual Focus
pqrs: Focus Position
CAM_2D Noise
Reduction
Direct
8x 01 04 53 0p FF
0::OFF 1:ON
y0 50 0p 0q 0r 0s FF
12
13
CV610-U2 / CV610-UB Operation Manual
VISCA Protocol
VISCA PAN / TILT ABSOLUTE POSITION VALUE
Pan Angle
-170
-135
-90
VISCA Value
0xF670
0xF868
0xFAF0
0xFD78
0x0000
0x0288
0x0510
0x0798
0x0990
Tilt Angle
VISCA Value
-30
0
0xFE50
0x0000
0x01B0
0x0360
0x510
y0 50 00 FF
y0 50 01 FF
y0 50 02 FF
Auto
Indoor mode
Outdoor mode
OnePush mode
ATW
30
60
90
CAM_WBModeIng
8x 09 04 35 FF
y0 50 03 FF
-45
y0 50 04 FF
0
y0 50 05 FF
Manual
45
CAM_RGainIng
CAM_BGainIng
8x 09 04 43 FF
8x 09 04 44 FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 00 FF
pq: R Gain
pq: B Gain
Full Auto
90
135
170
y0 50 03 FF
Manual
CAM_AEModeIng
8x 09 04 39 FF
y0 50 0A FF
Shutter priority
Iris priority
VISCA PAN / TILT ABSOLUTE POSITION VALUE
Pan(degree/second) Tilt(degree/second)
0.3
y0 50 0B FF
y0 50 0D FF
Bright
0
0.3
1
0
1
CAM_ShutterPosIng
CAM_IrisPosIng
8x 09 04 4A FF
8x 09 04 4B FF
8x 09 04 4C FF
8x 09 04 4D FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
y0 50 02 FF
pq: Shutter Position
pq: Iris Position
pq: Gain Position
pq: Bright Position
On
1
1
CAM_GainPosiIng
CAM_ BrightPosiIng
2
1.5
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.8
4.5
6
2
1.5
2.2
3.6
4.7
6
3
3
4
4
CAM_ExpCompModeIng
8x 09 04 3E FF
y0 50 03 FF
Off
5
5
CAM_ExpCompPosIng
CAM_ApertureIng
8x 09 04 4E FF
8x 09 04 42 FF
y0 50 00 00 0p 0q FF
y0 50 00 00 0p 0q FF
pq: ExpComp Position
pq: Aperture Gain
6
6
7
7
8
pp: Memory number last
operated.
CAM_MemoryIng
8x 09 04 3F FF
8x 09 06 06 FF
y0 50pp FF
8
8
10
12
15
18
23
30
39
48
59
69
80
y0 50 02 FF
On
9
9
SYS_MenuModeIng
y0 50 03 FF
Off
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
10
11
12
13
14
15
16
17
18
y0 50 02 FF
On
CAM_LR_ReverseIng
CAM_PictureFlipIng
8x 09 04 61 FF
8x 09 04 66 FF
y0 50 03 FF
Off
y0 50 02 FF
On
9
y0 50 03 FF
Off
15
19
25
32
38
45
58
75
88
105
120
CAM_IDIng
8x 09 04 22 FF
8x 09 00 02 FF
y0 50 0p 0q 0r 0s FF
pqrs: Camera ID
y0 50 ab cd
mn pq rs tu vw FF
CAM_VersionIng
y0 50 02 FF
y0 50 03 FF
On
Off
IR_Transfer
8x 09 06 1A FF
ww: PanMaxSpeed
zz: Tilt Max Speed
Pan-tiltMaxSpeedIng
Pan-tiltPosIng
8x 09 06 11 FF
8x 09 06 12 FF
y0 50 ww zz FF
y0 50 0w 0w 0w 0w
0z 0z 0z 0z FF
wwww: PanPosition
zzzz: Tilt Position
Note: (x) means the camera address; (y)=(x + 8).
14
15
CV610-U2 / CV610-UB Operation Manual
IR Transfer (IR PASS)
IR TRANSFER (IR PASS)
60/30mode 50/25mode
21
20
19
18
17
16
15
14
13
12
11
10
9
1/10000
1/6000
1/4000
1/3000
1/2000
1/1500
1/1000
1/725
1/500
1/350
1/250
1/180
1/125
1/100
1/90
1/10000
1/6000
1/3500
1/2500
1/1750
1/1250
1/1000
1/600
1/425
1/300
1/215
1/150
1/120
1/100
1/75
0
close
F14
F11
F9.6
F8
1. Currently the camera support NEC code format. For customization with other codes, please contact us.
sfer function via sending COM command.
1
2
3. Get the targeted remote controller point to the camera IR receiver, press keys on the remote controller,
then the camera will output the received IR code via VISCA IN port.
4. IR Transfer output format: XX XX XX XX FF
3
4
5
F6.8
F5.6
F4.8
F4
XX XX XX XX: Remote Controller Code
FF: End Code
6
7
5. The camera can save all setting, no need to re-set after power circle.
8
9
F3.4
F2.8
F2.4
F2
Shutter
speed
Iris
10
11
12
13
8
F1.6
UVC CONTROL
7
6
1/60
1/50
Control Requests
Control Selector
5
1/30
1/25
1
2
3
4
5
6
7
8
9
Brightness Control
Contrast Control
PU_BRIGHTNESS_CONTROL
PU_CONTRAST_CONTROL
4
1/15
1/12
Hue Control
PU_HUE_CONTROL
3
1/8
1/6
Saturation Control
Sharpness Control
Gamma Control
PU_SATURATION_CONTROL
PU_SHARPNESS_CONTROL
2
1/4
1/3
1
1/2
1/2
PU_GAMMA_CONTROL
0
1/1
1/1
White Balance Temperature Control
Gain Control
PU_WHITE_BALANCE_TEMPERATURE_CONTROL
PU_GAIN_CONTROL
0
0dB
8
16dB
18dB
20dB
22dB
24dB
26dB
28dB
30dB
Power Line Frequency Control
PU_POWER_LINE_FREQUENCY_CONTROL
CT_ZOOM_ABSOLUTE_CONTROL
CT_ZOOM_RELATIVE_CONTROL
CT_PANTILT_ABSOLUTE_CONTROL
CT_PANTILT_RELATIVE_CONTROL
1
2dB
9
10 Zoom (Absolute) Control
11 Zoom (Relative) Control
12 PanTilt (Absolute) Control
13 PanTilt (Relative) Control
2
4dB
10
11
12
13
14
15
3
6dB
Gain
Gain
4
8dB
5
10dB
12dB
14dB
6
7
16
17
|