Lexmark X 74 User Manual

X74-X75 All-In-One  
Contents  
iii  
Thank you for purchasing a Lexmark X74-X75 All-In-One!  
Congratulations on your new purchase. The Lexmark X74-X75 All-In-One  
combines the functionality of an inkjet printer, a scanner, a copier, and a  
fax machine all into a single, multifunction device making it one of the most  
exciting products on the market today.  
This User’s Guide takes you, step by step, from setting up your All-In-One  
to creating a variety of fun projects. Also included are sections describing  
the All-In-One software and troubleshooting information. Let’s get started!  
iv  
Learning about your All-In-One  
Setting up your All-In-One  
If you have not already done so, follow the steps on the setup sheet that  
came with your All-In-One to complete the hardware and software  
installation. If problems occur during the setup process, see Setup  
Troubleshooting on page 19.  
Understanding the parts of your All-In-One  
Paper guide  
Paper support  
Slide next to paper to  
Extend to load paper  
ensure proper feeding.  
into the All-In-One.  
Operator panel  
Use the buttons to operate the  
All-In-One (see page 2 for details  
about each of the buttons).  
Scanner unit  
Top cover  
Paper exit tray  
Lift to access the print  
cartridges.  
Lift to place an item on  
the scanner glass.  
Extend to hold paper as  
it exits the All-In-One.  
1
                   
USB cable connector  
Power supply  
Silver, metal  
contacts are on  
the top of the  
power supply.  
USB cable  
Using the Operator Panel  
Your All-In-One is equipped with an operator panel that lets you scan and  
copy with the press of a button.  
Power light  
Indicates whether or not the  
All-In-One is powered on.  
Paper Feed button  
Power button  
Feeds paper through the  
All-In-One. Press when the  
Status light is flashing.  
Turns your All-In-One on  
and off.  
Status light  
Scan button  
When flashing, indicates the  
All-In-One is out of paper or  
experiencing another type of  
problem.  
Automatically starts the  
scanning process and  
opens the All-In-One  
Center (see page 6).  
Black Copy button  
Color Copy button  
Press to make a black and  
white copy (your computer  
must be on for this to work).  
Press to make a color copy  
(your computer must be on  
for this to work).  
2
                       
Understanding your software  
Your All-In-One software consists of three main components:  
Print Properties (printing)  
The Lexmark X74-X75 All-In-One Center (scanning, copying, and  
faxing)  
The Lexmark X74-X75 Solution Center (troubleshooting,  
maintenance, and cartridge ordering information)  
While each component has a distinct function, they all work together to  
optimize the performance of your All-In-One.  
Using Print Properties  
Print Properties is the software that controls your All-In-One printing  
function. You can change the settings in Print Properties based on the type  
of project you are creating. You can open Print Properties from almost any  
program:  
1 Open your programs File menu.  
2 Click Print.  
3 In the Print dialog box, click the Properties, Preferences, Options,  
or Setup button (depending on the program). The Print Properties  
screen is displayed.  
Note: Some applications may open Print Properties differently.  
3
       
Once you open Print Properties, the Quality/Copies tab displays along with  
the I want to... menu.  
Print Properties  
Quality Copies tab and I want to... menu  
Print Properties  
tabs  
I want to... menu  
This easy-to-use  
projects menu  
helps you print  
photos, banners,  
envelopes,  
posters, and  
much more.  
Use the Quality/  
Copies, Paper  
Setup, and Print  
Layout tabs to  
select your  
printer settings.  
The I want to... menu  
The I want to... menu automatically appears when you open Print  
Properties. It contains a variety of task wizards to help you select the  
correct printer settings for your printing project. Close the menu for a full  
view of the Print Properties dialog box.  
4
 
Print Properties tabs  
All of your printer settings are on the three main tabs of the Print Properties  
software: the Quality/Copies tab, Paper Setup tab, and Print Layout tab.  
From this tab:  
Quality/Copies  
You can change these settings:  
Quality/Speed - Select a Quality/Speed setting based on  
your needs. A better quality gives you a higher resolution,  
but prints slower.  
Multiple Copies - Customize how your All-In-One prints  
multiple copies of a single print job.  
Print Color Images in Black and White - Select this to  
print color images on the screen in black and white.  
Paper Setup  
Print Layout  
Paper Type - Select the type of paper you are using.  
Paper Size - Select the size of the paper you are using.  
Orientation - Select how you want the document oriented  
on the printed page.  
Layout - Select the type of layout you want your document  
to have.  
Duplexing - Select this when you want to print on both  
sides of the paper.  
Note: For additional information about these settings,  
right-click a setting on the screen, and then select  
Whats This?  
Save Settings menu  
From the Save Settings menu, you can name and save your current Print  
Properties settings for future use. You can save up to five custom settings  
configurations.  
Options menu  
The Options menu lets you make changes to the Quality Options, Style  
Options, and Printing Status Options settings. For more information on  
these settings, open the Quality Options, Style Options, or Printing Status  
Options dialog box from the menu, and then click the Help button on the  
5
                   
dialog box. The Options menu also provides you with direct links to  
different parts of the Lexmark Solution Center (see page 9) as well as  
software version information.  
Using the Lexmark All-In-One Center  
The Lexmark All-In-One Center is the software that lets you scan, copy,  
and fax documents. You can open the All-In-One Center from a variety of  
locations:  
From the Start menu - click Start Programs Lexmark X74-X75  
Lexmark All-In-One Center.  
From the Desktop icon - double-click the Lexmark X74-X75  
All-In-One Center icon.  
From the operator panel - press Scan. For more information about  
using the operator panel, see page 2.  
Once you open the All-In-One Center, the All-In-One Main Page is  
displayed.  
All-In-One Center  
All-In-One Main Page  
6
     
The All-In-One Main Page  
The All-In-One Main Page consists of four main sections: Scan, Copy,  
Creative Tasks, and Preview area.  
From this section:  
Scan...  
You can do the following:  
Choose a program to send your scanned image to.  
Choose what type of image is being scanned.  
Choose how the scan will be used.  
Note: Click See More Scan Settings to view all  
settings.  
Copy...  
Choose the quantity and color of your copies.  
Select a quality setting for your copies.  
Adjust the size of the scanned area.  
Lighten or darken your copies.  
Enlarge or reduce your copies.  
Note: Click See More Copy Settings to view all  
settings.  
Creative Tasks...  
Choose from a variety of exciting, creative ideas.  
Enlarge or reduce an image.  
Print an image as a poster.  
E-mail an image to a friend.  
Modify an image with a photo editor.  
Edit text found in a scanned document using  
Optical Character Recognition (OCR).  
And much more!  
Preview area  
Scan preview - Use your mouse to select a region of  
the preview image to be scanned.  
Print/Copy preview - View an image of what will be  
printed or copied.  
Note: For more information about this page, click the Help  
button located in the top, right corner of the screen.  
7
                     
View Saved Images page  
The View Saved Images page lets you perform tasks with images that are  
saved on your computer. The View Saved Images page consists of three  
sections.  
From this section:  
Open with...  
You can do the following:  
Choose a program to send your saved image to.  
Print a Copy...  
Choose the quantity and color of your copies.  
Select a quality setting for your copies.  
Enlarge of reduce your copies.  
Note: Click See More Copy Settings to view all  
settings.  
Creative Tasks...  
Choose from a variety of exciting, creative ideas.  
Enlarge or reduce an image.  
Print an image as a poster.  
E-mail an image to a friend.  
Modify an image with a photo editor.  
Edit text found in a scanned document using  
Optical Character Recognition (OCR).  
And much more!  
Note: For more information about this page, click the Help  
button located in the top, right corner of the screen.  
Maintain/Troubleshoot page  
The Maintain/Troubleshoot page provides you with direct links to the  
Lexmark Solution Center. For more information about the Lexmark  
Solution Center, see the next section.  
Note: For more information about this page, click the Help  
button located in the top, right corner of the screen.  
8
                 
Using the Lexmark Solution Center  
The Lexmark Solution Center is a valuable information resource. To open  
the Lexmark Solution Center, click Start Programs Lexmark X74-X75  
Lexmark X74-X75 Solution Center. Once you open the Lexmark  
Solution Center, the Printer Status tab appears.  
Lexmark Solution Center  
Printer Status tab  
Printer Status  
Ink levels  
The Lexmark Solution Center consists of six tabs: Printer Status, How To,  
Troubleshooting, Maintenance, Contact Information, and Advanced.  
From this tab:  
You can do the following:  
Printer Status  
(Main dialog box)  
View the status of the All-In-One. For example, if the  
All-In-One is printing a document, the status is Busy  
Printing.  
View the ink levels of the print cartridges.  
How To  
Learn how to use basic features of the All-In-One such  
as the operator panel and the Lexmark All-In-One  
Center.  
Learn how to find and change settings.  
Learn how to scan, copy, fax, and print.  
Learn how to create fun projects using your All-In-One.  
Troubleshooting  
Learn tips about your current status.  
Solve All-In-One problems.  
9
             
From this tab:  
Maintenance  
You can do the following:  
Install a new print cartridge.  
View shopping options for new cartridges.  
Print a test page.  
Clean print nozzles to fix horizontal streaks.  
Align the print cartridges to fix blurry edges.  
Troubleshoot ink problems.  
Remove residue from Japanese postcards (Hagaki).  
Contact  
Learn how to contact Lexmark by phone.  
Information  
Advanced  
Change the appearance of the Printing Status window  
and turn printing voice notification on or off.  
Download new updates to the All-In-One software.  
Learn how to network your All-In-One in a Windows  
printer sharing environment.  
Obtain software version information.  
Note: For more information, click the Help button located in  
the bottom, right corner of the screen.  
10  
     
Using your All-In-One  
The following sections give you everything you need to know for basic  
printing, scanning, copying, and faxing. Youll be creating fun projects in no  
time at all.  
Printing  
Printing is the most basic function of your All-In-One. The Print Properties I  
want to... menu (see page 4) provides you with various printing wizards to  
help you easily complete more complicated tasks such as printing  
photographs, banners, or posters.  
1 Depending on what you want to print, load the appropriate type of  
paper into the All-In-One. Place the paper against the right side of  
the paper support, with the print side facing you. Your All-In-One is  
designed to accept the following types of paper:  
100 sheets of bond paper  
25 iron-on transfers  
50 transparencies  
10 sheets of greeting card stock  
10 sheets of inkjet photo paper  
100 sheets banner paper/continuous form paper  
25 sheets of labels  
11  
                     
2 Squeeze and slide the paper guide to the left edge of the paper.  
3 Make sure your All-In-One is turned on and receiving power.  
4 From your software programs File menu, click Print.  
5 In the Print dialog box, click the Properties, Preferences, Options,  
or Setup button (depending on the program). Print Properties  
appears.  
6 If your printing task is found on the I want to... menu, click it, and  
follow the instructions on the screen; otherwise, click Close at the  
bottom of the menu.  
7 Go to Quality/Copies tab and select your Quality/Speed and copy  
settings. Right-click a setting on the screen, and then select Whats  
This? to see details about a setting.  
Quality/Speed  
settings  
Copy settings  
12  
 
8 Go to the Paper Setup tab and select your paper type, paper size,  
and orientation. Right-click a setting on the screen, and then select  
Whats This? to see details about a setting.  
Paper size  
setting  
Paper type  
setting  
Orientation  
setting  
9 Go to the Print Layout tab and select the layout and duplexing  
settings for the type of document you are printing. Right-click a  
setting on the screen, and then select Whats This? to see details  
about a setting.  
Layout  
setting  
Duplexing  
setting  
10 Once you have applied all your desired settings in Print Properties,  
click OK at the bottom of the screen to return to the Print Dialog  
box.  
11 Click Print to complete your task.  
13  
Scanning  
Do you have photographs, postcards, or other items that you would like to  
reproduce electronically for use on your computer? The following steps  
show you how to use the scanner to scan and save images for use with  
your favorite computer programs.  
1 Open the top cover of your All-In-One.  
2 Place the item you want to scan face down on the glass. Make sure  
the upper left corner of the front of the item aligns with the arrow.  
3 Close the top cover.  
4 Open the Lexmark All-In-One Center (see page 6). The All-In-One  
Main Page appears.  
5 Click the Preview Now button located in the upper, right corner of  
the All-In-One Main Page. An image of your scanned item appears  
in the preview area.  
6 Using your mouse, click and drag to select a specific area of the  
preview image to scan.  
7 Click See More Scan Settings located in the Scan... section of the  
All-In-One Main Page to review and change your basic scan  
settings for the type of project you are creating.  
14  
       
8 From the Send Scanned Image To: drop-down menu, select a  
program to send the scanned image to, or click the Creative Tasks  
section to display a list of projects.  
Preview Now button  
Click to see a preview  
of your image.  
Scan Settings  
Adjust the settings for  
your scanned item.  
Preview Area  
See a preview of your  
image and select an  
area to be scanned.  
9 If you are sending your scanned image to a software program, click  
Scan Now to complete the scan. If you are using the Creative Tasks  
menu, follow the instructions on your screen.  
Copying  
Do you need to make photocopies? Copying is easy with the Lexmark  
All-In-One Center. The following steps show you how to make black and  
white, gray, or color copies.  
1 Open the top cover of your All-In-One.  
15  
   
2 Place the item you want to copy face down on the glass. Make sure  
the upper left corner of the front of the item aligns with the arrow.  
3 Close the top cover.  
4 Open the Lexmark All-In-One Center (see page 6). The All-In-One  
Main Page appears.  
Note: It is possible to make copies directly from the operator  
panel without opening the software (see page 2). Your  
computer must be powered on.  
5 Click See More Copy Settings located in the Copy... section of the  
All-In-One Main Page to review and change your basic copy  
settings.  
Preview Now button  
Click to see a preview  
of your image.  
Copy settings  
Adjust the settings for  
your copy.  
Preview area  
See a preview of your  
image and select an  
area to be copied.  
16  
 
6
Once you are satisfied with your preview image and copy settings,  
click Copy Now.  
Note: You may want to reduce or enlarge your image. If the  
document you want to copy is larger than the paper size  
you are copying to, you can reduce the image to fit the  
paper. Likewise, if the document you want to copy is  
extremely small, you may want to enlarge it.  
Faxing  
Do you need to send a fax? Your All-In-One can handle that, too. The  
following steps lead you through sending a fax using your computers  
modem.  
1 Open the top cover.  
2 Place the item you want to fax face down on the glass. Make sure  
the upper left corner of the front of the item aligns with the arrow.  
3 Close the top cover.  
4 Open the Lexmark All-In-One Center (see page 6).  
5 From the Creative Tasks section of the All-In-One Main Page, click  
Fax using your computers modem.  
6 Follow the instructions on the screen.  
17  
   
Troubleshooting  
This section helps you solve problems you may be experiencing with your  
All-In-One. Additional troubleshooting information is available in the  
Lexmark Solution Center. See page 9 to learn how to access the Lexmark  
Solution Center.  
Troubleshooting checklist  
Before you try to solve the problem, check the following:  
Is the power supply firmly attached to the back of your All-In-One  
and an electrical outlet?  
Are both your computer and your All-In-One powered on?  
Is your USB cable securely attached to your computer and your  
All-In-One?  
Did you remove the sticker and transparent tape from the back  
and bottom of both print cartridges (refer to your setup  
documentation for more information)?  
Is the black print cartridge secure in the right carrier and the color  
cartridge secure in the left carrier?  
Is the paper loaded correctly? Make sure you do not push the  
paper too far into the printer.  
Did you install the printer software correctly? Refer to your setup  
documentation for more information.  
18  
     
Setup troubleshooting  
Use this section to solve problems you may experience during setup.  
Power light did not come on  
Check the power supply connections.  
Press the Power button on the operator panel.  
Alignment page did not print  
Make sure you completely removed the sticker and transparent  
tape from the back and bottom of both print cartridges. Refer to  
your setup documentation for information about installing print  
cartridges.  
Make sure the black print cartridge is secure in the right carrier  
and the color cartridge is secure in the left carrier.  
Make sure you loaded the paper correctly and did not push it too  
far into the All-In-One.  
When I inserted the All-In-One software CD, nothing  
happened  
From the Desktop, double-click the My Computer icon, and then  
double-click your CD-ROM drive icon.  
19  
     
Software installation appears incomplete  
You software may not have been installed properly. Try the  
following:  
1 If you are using Windows 98, Windows Me, or Windows 2000 click  
Start Settings Control Panel. If you are using Windows XP,  
click Start Control Panel Performance and Maintenance.  
2 Double-click the System icon.  
3 If you are using Windows 98 or Windows Me, click the Device  
Manager tab. If you are using Windows 2000 or Windows XP, click  
the Hardware tab, and then click the Device Manager button.  
4 Look for the Other Devices category. If there are any Lexmark  
devices found here, highlight them and press the Delete key.  
Note: The Other Devices category appears only when  
unknown devices are present. You should not delete any  
Lexmark items unless they are present under the Other  
Devices category.  
5 Insert the CD and install the software again. Do not restart your  
computer.  
20  
 
All-In-One is not communicating with the computer  
Disconnect and reconnect both ends of the USB cable (refer to  
your setup documentation for details).  
Unplug the All-In-One from the electrical wall outlet, and then  
reconnect the power supply (refer to your setup documentation  
for details). Plug the All-In-One back in and turn the power back  
on.  
Restart your computer. If problems still persist, see Uninstalling  
Printing troubleshooting  
All-In-One prints slowly  
Close all programs not in use. The memory resources may be too  
low.  
Make sure your Print Properties Quality/Speed setting is set on  
Normal or Quick Print. See page 5 for help.  
Try printing a smaller file. If the memory resources are too low,  
you may not be able to print a very large file. Consider purchasing  
more memory.  
Note: If you scanned a photograph with your All-In-One, the  
file size could be too large to print with a selected  
scanning resolution higher than 300 dpi.  
21  
 
All-In-One has a paper jam  
Follow the instructions on the screen for clearing the paper jam.  
Make sure you are using paper designed for an inkjet printer. See  
page 11 for a list of recommended papers.  
Make sure you are correctly loading the paper. See page 11 for  
instructions.  
Make sure the paper guide is against the left edge of the paper.  
See page 12 for details.  
Print is too dark or smudged  
Remove the paper as it exits and let the ink dry before handling.  
Adjust your Quality/Speed setting in Print Properties (see  
page 5). The Better or Best Quality/Speed setting may cause  
smearing if used with plain paper. Try using the Normal setting.  
Vertical lines are jagged or edges are not smooth  
Adjust your Quality/Speed setting in Print Properties (see  
page 5). For best print quality, select Better or Best.  
Align the print cartridges. If the print cartridges are out of  
alignment, vertical lines appear jagged. To align the print  
cartridges:  
1 Open the Lexmark Solution Center (see page 9).  
2 From the Maintenance tab, click Align to fix blurry edges.  
22  
 
White lines appear in graphics or solid black areas  
Clean the print cartridge nozzles. Going long periods without  
using your All-In-One can sometimes cause the print cartridge  
nozzles to become clogged. To clean the cartridge nozzles:  
1 Open the Lexmark Solution Center (see page 9).  
2 From the Maintenance tab, click Clean to fix horizontal streaks.  
Scanning, copying, and faxing troubleshooting  
Scanning or using a scanned image with a software  
program takes a long time or freezes the computer  
Lower the scanning resolution. The scanning resolution is much  
different than the printing resolution and is generally set much  
lower. You can achieve excellent results with a 300 dpi scanning  
resolution. To change your scanning resolution:  
1 Open the Lexmark All-In-One Center (see page 9).  
2 From the Scan... section, click See More Scan Settings.  
3 Click Display Advanced Scan Settings.  
4 From the Scan tab of Advanced Scan Settings, enter a scan  
resolution less than or equal to 300 dpi.  
23  
   
Scanning was not successful  
You software may not have been installed properly. Try the  
following:  
1 If you are using Windows 98, Windows Me, or Windows 2000 click  
Start Settings Control Panel. If you are using Windows XP,  
click Start Control Panel Performance and Maintenance.  
2 Double-click the System icon.  
3 If you are using Windows 98 or Windows Me, click the Device  
Manager tab. If you are using Windows 2000 or Windows XP, click  
the Hardware tab, and then click the Device Manager button.  
4 Look for the Other Devices category. If there are any Lexmark  
devices found here, highlight them and press the Delete key.  
Note: The Other Devices category appears only when  
unknown devices are present. You should not delete any  
Lexmark items unless they are present under the Other  
Devices category.  
5 Insert the CD and install the software again. Do not restart your  
computer.  
Edge of the copy did not print  
If your copy was made using the Color Copy button on the  
Operator panel, try using the Lexmark All-In-One Center and  
adjusting the Original size setting:  
1 Open the Lexmark All-In-One Center (see page 6).  
2 From the Copy... section, make sure Auto-Detect is listed as the  
Original size setting.  
24  
Copy button on the operator panel did not work  
Make sure you have properly installed the software (see your  
setup documentation). The software must be installed for the  
copier to work.  
Make sure your computer is turned on. The computer must be  
turned on in order for your All-In-One to work.  
Fax function did not work  
Make sure your computer is connected to a phone line. A phone  
connection is required for faxing to work.  
Uninstalling and reinstalling the software  
If the All-In-One software is not functioning properly or a communications  
error message appears when you try to use your All-In-One, you may need  
to uninstall, and then reinstall the printer software.  
1 From your desktop, click Start Programs Lexmark X74-X75  
Lexmark X74-X75 Uninstall.  
Note: If Uninstall is not an option on your menu, see Software  
2 Follow the instructions on your screen to uninstall the All-In-One  
software.  
3 Restart your computer before reinstalling the software.  
4 Insert the CD and follow the instructions on your screen to install  
the software. Refer to your setup documentation for details.  
25  
   
Appendix  
Reorient or relocate the  
receiving antenna.  
Industry Canada  
Electronic  
compliance statement  
emission notices  
Increase the separation  
between the equipment  
and receiver.  
This Class B digital  
apparatus meets all  
requirements of the  
Canadian  
Interference-Causing  
Equipment Regulations.  
Federal  
Communications  
Commission (FCC)  
compliance information  
statement  
Connect the equipment  
into an outlet on a circuit  
different from that to  
which the receiver is  
connected.  
Avis de conformité aux  
normes dIndustrie  
Canada  
Cet appareil numérique de la  
classe B respecte toutes les  
exigences du Règlement sur  
le matériel brouilleur du  
Canada.  
The Lexmark X74-X75  
All-In-One has been tested  
and found to comply with the  
limits for a Class B digital  
device, pursuant to Part 15  
of the FCC Rules. Operation  
is subject to the following two  
conditions: (1) this device  
may not cause harmful  
interference, and (2) this  
device must accept any  
interference received,  
Consult your point of  
purchase or service  
representative for  
additional suggestions.  
The manufacturer is not  
responsible for any radio or  
television interference  
caused by using other than  
recommended cables or by  
unauthorized changes or  
modifications to this  
equipment. Unauthorized  
changes or modifications  
could void the user's  
authority to operate this  
equipment.  
European Community  
(EC) directives  
conformity  
This product is in conformity  
with the protection  
including interference that  
may cause undesired  
operation.  
The FCC Class B limits are  
designed to provide  
reasonable protection  
requirements of EC Council  
directives 89/336/EEC and  
73/23/EEC on the  
To assure compliance with  
FCC regulations on  
electromagnetic interference  
for a Class B computing  
device, use a properly  
shielded and grounded cable  
such as Lexmark part  
number 1329605. Use of a  
substitute cable not properly  
shielded and grounded may  
result in a violation of FCC  
regulations.  
against harmful interference  
in a residential installation.  
This equipment generates,  
uses and can radiate radio  
frequency energy and, if not  
installed and used in  
approximation and  
harmonization of the laws of  
the Member States relating  
to electromagnetic  
compatibility and safety of  
electrical equipment  
designed for use within  
certain voltage limits.  
accordance with the  
instructions, may cause  
harmful interference to radio  
communications. However,  
there is no guarantee that  
interference will not occur in  
a particular installation. If  
this equipment does cause  
harmful interference to radio  
or television reception, which  
can be determined by  
A declaration of conformity  
with the requirements of the  
directives has been signed  
by the Director of  
Manufacturing and Technical  
Support, Lexmark  
International, S.A., Boigny,  
France.  
Any questions regarding this  
compliance information  
statement should be directed  
to:  
Director of Lab Operations  
Lexmark International, Inc.  
740 West New Circle Road  
Lexington, KY 40550  
(859) 232-3000  
This product satisfies the  
Class B limits of EN 55022  
and safety requirements of  
EN 60950.  
turning the equipment off  
and on, the user is  
encouraged to try to correct  
the interference by one or  
more of the following  
measures:  
26  
       
Japanese VCCI notice  
The United Kingdom  
Telecommunications  
Act 1984  
This apparatus is approved  
under the approval number  
NS/G/1234/J/100003 for the  
indirect connections to the  
public telecommunications  
systems in the United  
Kingdom.  
ENERGY STAR  
The EPA ENERGY STAR  
Office Equipment program is  
a partnership effort with  
office equipment  
manufacturers to promote  
the introduction of  
energy-efficient products  
and to reduce air pollution  
caused by power generation.  
Companies participating in  
this program introduce  
products that power down  
when they are not being  
used. This feature will cut  
the energy used by up to 50  
percent. Lexmark is proud to  
be a participant in this  
program.  
As an ENERGY STAR  
Partner, Lexmark  
International, Inc. has  
determined that this product  
meets the ENERGY STAR  
guidelines for energy  
efficiency.  
27  
Index  
A
M
Lexmark All-In-One  
Center  
Maintain/Troubleshoot  
F
H
O
operator panel  
B
black and white, printing  
I
ink cartridges  
see duplexing  
ink levels  
P
paper  
C
L
cartridges  
Lexmark All-In-One  
Contact Information tab  
Lexmark Solution Center  
photographs  
Contact Information  
D
E
electronic emission  
28  
 
30  
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc.,  
registered in the United States and/or other countries.  
© 2002 Lexmark International, Inc.  
740 West New Circle Road  
Lexington, Kentucky 40550  

Zenoah G26 Air User Manual
Xerox Wc5230 User Manual
Xerox All In One Printer 7232 User Manual
Whirlpool Acq189xr1 User Manual
Toshiba All In One Printer E Studio202s User Manual
Samsung Avmwh052ca0 User Manual
KENWOOD KAC 304 User Manual
EMERSON EVC466 User Manual
DELL S2419H User Manual
CRAFTSMAN 917.275640 User Manual