LG 43LX340H UF User Manual

OWNER’S MANUAL

Safety and Reference

LED TV*

* LG LED TVs are LCD TVs with LED backlighting.

Please read this manual carefully before operating

your TV and retain it for future reference.

32LX340H

40LX340H

43LX340H

49LX340H

55LX340H

43UX340H

49UX340H

55UX340H

65UX340H

www.lg.com

*MFL68925862*

P/NO : MFL68925862 (1612-REV01)

• Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

appliance, and have the cord replaced with

an exact replacement part by an authorized

servicer. Protect the power cord from physical or

mechanical abuse, such as being twisted, kinked,

pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and

the point where the cord exits the appliance. Do

not move the TV with the power cord plugged

in. Do not use a damaged or loose power cord.

Be sure do grasp the plug when unplugging the

power cord. Do not pull on the power cord to

unplug the TV.

• Unplug this apparatus during lightning storms

or when unused for long periods of time.

• Warning - To reduce the risk of fire or electrical

shock, do not expose this product to rain,

moisture or other liquids. Do not touch the TV

with wet hands. Do not install this product near

flammable objects such as gasoline or candles,

or expose the TV to direct air conditioning.

• Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has

been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

• Do not expose to dripping or splashing and

do not place objects filled with liquids, such as

vases, cups, etc. on or over the apparatus (e.g.,

on shelves above the unit).

• Do not press strongly upon the panel with a

hand or a sharp object such as a nail, pencil, or

pen, or make a scratch on it.

• Grounding

• Do not stick metal objects or any other

conductive material into the power cord. Do

not touch the end of the power cord while it is

plugged in.

• Keep the packing anti-moisture material or

vinyl packing out of the reach of children.

Anti-moisture material is harmful if swallowed.

If swallowed, induce vomiting and go to the

nearest hospital. Additionally, vinyl packing can

cause suffocation. Keep it out of the reach of

children.

(Except for devices which are not grounded.)

Ensure that you connect the earth ground wire

to prevent possible electric shock (i.e., a TV

with a three-prong grounded AC plug must

be connected to a three-prong grounded AC

outlet). If grounding methods are not possible,

have a qualified electrician install a separate

circuit breaker. Do not try to ground the unit by

connecting it to telephone wires, lightning rods,

or gas pipes.

• CAUTION concerning the Power Cord

(Can differ by country):

Power

Supply

Circuit

Check the specification page of this owner’s

manual to be certain. Do not connect too many

appliances to the same AC power outlet as this

could result in fire or electric shock. Do not

overload wall outlets. Overloaded wall outlets,

loose or damaged wall outlets, extension cords,

frayed power cords, or damaged or cracked

wire insulation are dangerous. Any of these

conditions could result in electric shock or fire.

Periodically examine the cord of your appliance,

and if its appearance indicates damage or

deterioration, unplug it, discontinue use of the

Breaker

• As long as this unit is connected to the AC wall

outlet, it is not disconnected from the AC power

source even if the unit is turned off.

• Ventilation

Install your TV where there is proper ventilation.

Do not install in a confined space such as a

bookcase. Do not cover the product with cloth or

other materials while plugged. Do not install in

excessively dusty places.

• Do not attempt to modify this product in any

way without written authorization from LG

Electronics. Unauthorized modification could

void the user’s authority to operate this product.

• Outdoor Antenna Grounding

• If you smell smoke or other odors coming from

the TV, unplug the power cord and contact an

authorized service center.

(Can differ by country):

If an outdoor antenna is installed, follow the

precautions below. An outdoor antenna system

should not be located in the vicinity of overhead

power lines or other electric light or power

circuits, or where it can come in contact with

such power lines or circuits as death or serious

injury can occur. Be sure the antenna system is

grounded to provide some protection against

voltage surges and built-up static charges.

Section 810 of the National Electrical Code (NEC)

in the U.S.A. provides information with respect

to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding

conductors, location of antenna discharge

unit, connection to grounding electrodes, and

requirements for the grounding electrode.

Antenna grounding according to the National

Electrical Code, ANSI/NFPA 70

• Keep the product away from direct sunlight.

• Never touch this apparatus or antenna during a

lightning storm.

• When mounting a TV on the wall, make sure not

to install the TV by hanging the power and signal

cables on the back of the TV.

• Do not allow an impact shock, any objects to fall

into the product, and do not drop anything onto

the screen.

• DISCONNECTING THE DEVICE FROM THE

MAIN POWER

The power plug is the disconnecting device.

In case of an emergency, the power plug must

remain readily accessible.

• Batteries

Store the accessories (battery, etc.) in a safe

location out of the reach of children.

• This apparatus uses batteries. In your community

there might be regulations that require you

to dispose of these batteries properly due to

environmental considerations. Please contact

your local authorities for disposal or recycling

information.

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Ground Clamp

• Do not dispose of batteries in a fire.

• Do not short circuit, disassemble, or allow the

batteries to overheat.

• Do not use high voltage electrical equipment

near the TV, (e.g., a bug zapper.)

This may result in product malfunction.

• Dot Defect

The panel is a high technology product with

resolution of two million to six million pixels.

In a very few cases, you could see fine dots on

the screen while you’re viewing the TV. Those

dots are deactivated pixels and do not affect the

performance and reliability of the TV.

Electric Service

Equipment

Grounding Conductor

(NEC Section 810-21)

Ground Clamp

Power Service Grounding

Electrode System

(NEC Art 250, Part H)

NEC: National Electrical Code

• Cleaning

When cleaning, unplug the power cord and wipe

gently with a soft cloth to prevent scratching. Do

not spray water or other liquids directly on the

TV as electric shock may occur. Do not clean with

chemicals such as alcohol, thinners, or benzene.

• Moving

Make sure the product is turned off, unplugged,

and all cables have been removed. It may take 2

or more people to carry larger TVs. Do not press

or put stress on the front panel of the TV.

• Generated Sound

• Only use an authorized AC adapter and power

cord approved by LG Electronics. Otherwise, this

may result in fire, electric shock, malfunction, or

product deformation.

Cracking noise A cracking noise that occurs

when watching or turning off the TV is

generated by plastic thermal contraction due to

temperature and humidity. This noise is common

for products where thermal deformation is

required.

Electrical circuit humming/panel buzzing

A low level noise is generated from a high-

speed switching circuit, which supplies a large

amount of current to operate a product. It varies

depending upon the product. This generated

sound does not affect the performance and

reliability of the product.

• Never Disassemble the AC adapter or power

cord. This may result in fire or electric shock.

• Take care not to touch the ventilation openings.

When watching the TV for a long period, the

ventilation openings may become hot. This does

not affect the performance of the product or

cause defects in the product.

• Do not install this product on a wall if it could be

exposed to oil or oil mist. This may damage the

product and cause it to fall.

• Handle the adapter carefully to avoid dropping

or striking it. An impact could damage the

adapter.

• If the TV feels cold to the touch, there may

be a small flicker when it is turned on. This is

normal; there is nothing wrong with TV. Some

minute dot defects may be visible on the screen,

appearing as tiny red, green, or blue spots.

However, they have no adverse effect on the TV’s

performance. Avoid touching the LCD screen or

holding your finger(s) against it for long periods

of time. Doing so may produce some temporary

distortion effects on the screen.

• If water or another substance enters the product

(like an AC adapter, power cord, TV), disconnect

the power cord and contact the service center

immediately.

• Displaying a still image for a prolonged period of

time may cause an image sticking.

Avoid displaying a fixed image on the TV screen

for a extended length of time.

Otherwise, this may result in fire or electric

shock.

FCC Radio Frequency Interference

Requirements (for UNII devices)

FCC Notice

(For USA)

High power radars are allocated as primary users

of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands.

These radar stations can cause interference with

and/or damage this device. This device cannot be

co-located with any other transmitter.

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses

and can radiate radio frequency energy and, if

not installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one or more of

the following measures:

FCC RF Radiation Exposure Statement

[For having wireless function (WLAN, Bluetooth,...)]

This equipment complies with FCC radiation

exposure limits set forth for an uncontrolled

environment. This transmitter must not be

colocated or operating in conjunction with any

other antenna or transmitter. This equipment

should be installed and operated with minimum

distance 20 cm (7.8 inches) between the antenna

and your body. Users must follow the specific

operating instructions for satisfying RF exposure

compliance.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment

and the receiver.

- Connect the equipment to an outlet on a circuit

different from that to which the receiver is

connected.

Industry Canada Statement

(For Canada)

[For having wireless function (WLAN, Bluetooth,...)]

- Consult the dealer or an experienced radio/TV

technician for help.

This device complies with RSS-210 of the Industry

Canada Rules. Operation is subject to the following

two conditions:

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference and (2) this device must accept any

interference received, including interference that

may cause undesired operation of the device. Any

changes or modifications in construction of this

device which are not expressly approved by the

party responsible for compliance could void the

user’s authority to operate the equipment.

1. This device may not cause interference and

2. This device must accept any interference,

including interference that may cause undesired

operation of the device.

IC Radiation Exposure Statement

(For Canada)

[For having wireless function (WLAN, Bluetooth,...)]

This equipment complies with IC radiation

exposure limits set forth for an uncontrolled

environment. This equipment should be installed

and operated with minimum distance 20 cm (7.8

inches) between the radiator & your body.

NOTE : THE MANUFACTURER IS NOT RESPONSIBLE

FOR ANY RADIO OR TV INTERFERENCE CAUSED

BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT. SUCH MODIFICATIONS COULD

VOID THE USER’S AUTHORITY TO OPERATE THE

EQUIPMENT.

Preparing

WARNING

(For Canada)

[For product having the wireless function using 5

GHz frequency bands]

• The device for operation in the band 5150–5250

MHz is only for indoor use to reduce the

potential for harmful interference to co-channel

mobile satellite systems;

• The maximum antenna gain permitted for

devices in the bands 5250–5350 MHz and

5470–5725 MHz shall comply with the EIRP limit;

and

• The maximum antenna gain permitted for

devices in the band 5725–5825 MHz shall

comply with the EIRP limits specified for point-

to-point and non point-to-point operation as

appropriate.

NOTE

• Image shown may differ from your TV.

• Your TV’s OSD (On Screen Display) may differ

slightly from that shown in this manual.

• The available menus and options may differ from

the input source or product model that you are

using.

• New features may be added to this TV in the

future.

• The items supplied with your product may vary

depending upon the model.

• Product specifications or contents of this manual

may be changed without prior notice due to

upgrade of product functions.

• For an optimal connection, HDMI cables and USB

devices should have bezels less than 10 mm (0.39

inches) thick and 18 mm (0.7 inches) width.

• Use an extension cable that supports USB 2.0 if

the USB cable or USB flash drive does not fit into

your TV’s USB port.

• High-power radars are allocated as primary users

(i.e. priority users) of the bands 5250–5350 MHz

and 5650–5850 MHz and that these radars could

cause interference and/or damage to LE-LAN

devices.

• Use a certified cable with the HDMI logo

attached. If you do not use a certified HDMI

cable, the screen may not display or a

connection error may occur.

• Recommended HDMI cable types (3 m or less)

- High-Speed HDMI®/™ cable

- High-Speed HDMI®/™ cable with Ethernet

Note to Cable/TV Installer

(For USA and Canada)

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the

National Electric Code (U.S.A.). The code provides

guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected

to the grounding system of the building, as close

to the point of the cable entry as practical.

*A 10 mm (0.39 inches)

*B 18 mm (0.7 inches)

CAUTION

• Do not use any unapproved items to ensure the

safety and lifespan of the product.

• Any damages or injuries by using unapproved

items are not covered by the warranty.

• Some models appear to have a thin film on the

screen. It is actually part of the screen; do not

remove it.

• When attaching the stand to the TV set, place

the screen facing down on a cushioned table or

flat surface to protect the screen from scratches.

• Make sure that the screws are fastened tightly.

(If they are not fastened securely enough, the TV

may tilt forward after being installed.)

• Do not fasten the screws with excessive force;

otherwise, they may be worn out and become

loose.

Warning when using USB storage devices

CAUTION

• Do not push, rub, or hit the surface with your

fingernail or a sharp object, as this may result in

scratches on the screen and image distortions.

• Do not use any chemicals, such as waxes,

benzene, alcohol, thinners, insecticides, air

fresheners, or lubricants, as these may damage

the screen’s finish and cause discoloration.

• Do not spray liquid onto the surface. If water

enters the TV, it may result in fire, electric shock,

or malfunction.

• USB storage devices with a built-in auto

recognition program or its own driver may not

work.

• Some USB storage devices may not work or may

work improperly.

• Use only those USB storage devices formatted

with FAT32 or NTFS File System provided by

Windows.

• For external USB HDD, use devices with less than

5V-rated voltages and 500 mA-rated current.

• It is recommended to use USB flash drive with 32

GB or less and USB HDD with 2 TB or less.

• If a USB HDD with power-saving function does

not work properly, turn the power off and on.

For more information, refer to the user manual

of USB HDD.

Power Cord

Remove the accumulated dust or dirt on the power

cord regularly.

• Data in the USB storage device can be damaged

so back up important files in other devices. Data

maintenance is the user’s responsibility. The

manufacturer is not responsible for data loss.

Lifting and Moving the TV

When moving or lifting the TV, read the following

to prevent the TV from being scratched or

damaged and for safe transportation regardless of

its type and size.

• It is recommended to move the TV in the box or

packing material that the TV originally came in.

• Before moving or lifting the TV, disconnect the

power cord and all cables.

Maintenance

Cleaning your TV

Clean your TV regularly to keep it at peak

performance and to extend the product’s lifespan.

• When holding the TV, the screen

should face away from you to

avoid damage.

CAUTION

• Before cleaning, turn the power off and

disconnect the power cord and all other cables.

• When the TV is left unattended or unused for a

long time, disconnect the power cord from the

wall outlet to prevent possible damage from

lightning or power surges.

• Hold the top and bottom of the TV frame firmly.

Make sure not to hold the transparent part,

speaker, or speaker grille area.

Screen, Frame, Cabinet, and Stand

To remove dust or light dirt, wipe the surface with

a dry, clean, and soft cloth.

To remove major dirt, wipe the surface with a soft

cloth dampened in clean water or a diluted mild

detergent. Then wipe immediately with a dry cloth.

• Use at least two people to move

a large TV.

• When transporting the TV by

hand, hold the TV as shown in the

following illustration.

• When transporting the TV, do not expose the TV

to jolts or excessive vibration.

• When transporting the TV, keep the TV upright;

never turn the TV on its side or tilt towards the

left or right.

• When handling the TV, be careful not to damage

the protruding joystick button.

NOTE

• Move the joystick up, down, left, or right. Be

careful not to press the joystick button. If you

press the joystick button first, you may not be

able to adjust the volume level and/or scroll

through saved channels.

Adjusting the Menu

CAUTION

• Avoid touching the screen at all times, as this

may result in damage to the screen.

• Do not place the product on the floor with its

front facing down without padding. Failure to do

so may result in damage to the screen.

• Do not move the TV by holding the cable

holders, as the cable holders may break, and

injuries and damage to the TV may occur.

(Depending upon model)

When the TV is turned on, press the joystick button

one time. You can adjust the menu items moving

the joystick button up, down, left, or right.

Turns the power off.

Accesses the main menu.

Clears on-screen displays and returns to TV viewing

Changes the input source.

Using the Joystick Button

Mounting on a Table

(Image shown may differ from your TV.)

You can operate the TV by pressing the button or

moving the joystick left, right, up, or down.

Lift and tilt the TV into its upright position on a

table.

- Leave a 10 cm (4 inches) (minimum) space

from the wall for proper ventilation.

Joystick Button

10 cm

(4 inches)

10 cm

Basic Functions

10 cm

When the TV is turned off, place your

finger on the joystick button, press it

once, and release it.

Power On

Power Off

When the TV is turned on, place your

finger on the joystick button, press it

once for a few seconds, and release it.

(However, if the menu button is on the

screen, pressing and holding the joystick

button will let you exit the menu.)

2 Connect the power cord to a wall outlet.

CAUTION

• Do not place the TV near or on sources of heat,

as this may result in fire or other damage.

If you place your finger over the joystick

button and move it left or right, you can

adjust the volume level.

Volume

Control

If you place your finger over the joystick

button and move it up or down, you can

scroll through the saved channels.

Channels

Control

Adjusting the Angle of the TV

to Suit View

Stand

(Depending upon model)

Swivel 20 degrees to the left or right and adjust the

angle of the TV to suit your view.

Desk

NOTE

• Screw: M5 x L (*L: Table depth + 8~10 mm)

ex) Table depth: 15 mm, Screw: M5 x L25

20˚

[TYPE 2]

CAUTION

• When adjusting the angle of the TV, watch out

for your fingers.

- Personal injury may occur if hands or fingers

are pinched. If the product is tilted too much, it

may fall, causing damage or injury.

Attaching the TV to a desk

(optional)

(Depending upon model)

The TV should be attached to a desk so it cannot

be pulled in a forward/backward direction,

potentially causing injury or damaging the

product.

2-Screws, 2-Washers, 2-Nuts

(provided as parts of the product.)

[TYPE 1]

Stand

Desk

4-Screws

(Not provided as parts of the product.)

Securing the TV to a Wall

(optional)

(Depending upon model)

(Image shown may differ from your TV.)

Mounting on a Wall

An optional wall mount can be used with your

LG Television. Consult with your local dealer for

a wall mount that supports the VESA standard

used by your TV model. Carefully attach the wall

mount bracket at the rear of the TV. Install the wall

mount bracket on a solid wall perpendicular to the

floor. If you are attaching the TV to other building

materials, please contact qualified personnel to

install the wall mount. Detailed instructions will

be included with the wall mount. We recommend

that you use an LG brand wall mount. The LG wall

mount is easy to adjust or to connect the cables.

When you do not use LG’s wall mount bracket,

use a wall mount bracket where the device is

adequately secured to the wall with enough space

to allow connectivity to external devices. If you are

using a non-adjustable mount, attach the mount

to the wall. Attach the cables to the TV first, then

attach the TV to the mount.

Insert and tighten the eye-bolts or TV brackets

and bolts on the back of the TV.

- If there are bolts inserted at the eye-bolts

position, remove the bolts first.

10 cm

(4 inches)

2 Mount the wall brackets with the bolts to the

wall. Match the location of the wall bracket and

the eye-bolts on the rear of the TV.

10 cm

3 Connect the eye-bolts and wall brackets tightly

with a sturdy rope or cable. Make sure to keep

the rope parallel to the flat surface.

10 cm

CAUTION

• Make sure that children do not climb on or hang

Make sure to use screws and wall mounts that

meet the VESA standard. Standard dimensions for

the wall mount kits are described in the following

table.

on the TV.

NOTE

• Use a platform or cabinet that is strong and large

enough to support the TV securely.

• Brackets, bolts, and ropes are optional. You can

obtain additional accessories from your local

dealer.

32/40/43LX340H 49/55LX340H

Model

43UX340H

49/55UX340H

VESA (A x B)

Standard screw

Number of screws

200 x 200

300 x 300

Wall mount bracket LSW240B

LSW350B

MSW240

(optional)

MSW240

Model

65UX340H

VESA (A x B)

Standard screw

Number of screws

300 x 300

Wall mount bracket

(optional)

LSW350B

• When attaching a wall mounting bracket to the

TV, insert the wall mount inner spacers into the

TV wall mount holes to adjust the vertical angle

of the TV. (Use only when provided with your

particular model.)

CAUTION

• Disconnect the power before moving or

installing the TV. Otherwise electric shock may

occur.

• Remove the stand before installing the TV on a

wall mount by performing the stand attachment

in reverse.

Provided Item

• If you install the TV on a ceiling or slanted wall,

it may fall and result in severe injury. Use an

authorized LG wall mount and contact the local

dealer or qualified personnel. When using a

third-party wall mount, it is not covered by the

warranty.

Wall Mount Spacer

• Do not overtighten the screws as this may cause

damage to the TV and void your warranty.

• Use the screws and wall mounts that meet the

VESA standard. Any damages or injuries by

misuse or using an improper accessory are not

covered by the warranty.

Connections (Notifications)

You can connect various external devices to the TV.

Supported external devices are: HD receivers, DVD

players, VCRs, audio systems, USB storage devices,

PC, gaming devices, and other external devices. For

more information on external device’s connection,

refer to the manual provided with each device.

NOTE

• Use the screws that are listed in the VESA

standard screw specifications.

• The wall mount kit includes an installation

manual and necessary parts.

NOTE

• The wall mount bracket is optional. You can

obtain additional accessories from your local

dealer.

• This model supports 4K (ULTRA HD) videos only

in HDMI input. (For UX340H series)

• ULTRA HD videos are not supported in the tuner

or USB input. (For UX340H series)

• If you record a TV program on a DVD recorder or

VCR, make sure to connect the TV signal input

cable to the TV through a DVD recorder or VCR.

For more information about recording, refer to

the manual provided with the connected device.

• The external device connections shown may

differ slightly from illustrations in a manual.

• Connect external devices to the TV regardless

about the order of the TV port.

• The length of screws may differ depending upon

the wall mount. Make sure to use the proper

length.

• For more information, refer to the manual

supplied with the wall mount.

• When using the wall mounting bracket, apply

the adhesive protective label to cover the

unused stand openings. This will prevent the

accumulation of dust and dirt. (Use only when

provided with your particular model.)

Provided Item

• If you connect a gaming device to the TV, use the

cable supplied with the gaming device.

• Refer to the external equipment’s manual for

operating instructions.

Adhesive

protective label

Connecting to an Antenna or

Cable

CAUTION

• Do not mix old and new batteries, as this may

damage the remote control.

Connect an antenna, cable, or cable box to watch

TV while referring to the following. The illustrations

may differ from the actual items and an RF cable is

optional.

CAUTION

• Make sure not to bend the copper wire of the RF

cable.

Copper wire

• Complete all connections between devices, and

then connect the power cord to the power outlet

to prevent damage to your TV.

NOTE

• Use a signal splitter to use 2 TVs or more.

• DTV Audio Supported Codec: MPEG,

Dolby Digital.

• Direct ULTRA HD broadcast is unavailable in

areas without a ULTRA HD signal. (For UX340H

series)

(POWER) Turns the TV on or off.

Returns to the last TV channel.

Activates or deactivates the subtitles.

Selects an AV mode.

Resizes an image.

Other Connections

Changes the input source.

Connect your TV to external devices. For the best

picture and audio quality, connect the external

device and the TV with the HDMI cable.

Number button Enters numbers.

(DASH) Inserts a dash between numbers such as 2-1

NOTE

and 2-2.

• Use only with the 3-pole 3.5 mm stereo jack.

• Do not connect your headphones or earphones

to the port for connecting an external speaker.

Accesses the saved channel list.

Alternates between the two last channels

selected (pressing repeatedly).

Adjusts the volume level.

Remote Control

(Image shown may differ from your TV.)

Accesses your favorite channel list.

Digital signal : Changes the audio language.

Analog signal : Changes the MTS sound.

The descriptions in this manual are based on

the buttons on the remote control. Please read

this manual carefully and use the TV correctly. To

install batteries, open the battery cover, replace

batteries (1.5 V AAA) matching the and ends

to the label inside the compartment, and close

the battery cover. Failure to match the correct

polarities of the battery may cause the battery

to burst or leak, resulting in fire, personal injury,

or ambient pollution. To remove the batteries,

perform the installation actions in reverse. This

remote uses infrared light. When in use, it should

be pointed in the direction of the TV’s remote

sensor.

Mutes all sounds.

Scrolls through the saved channels.

Moves to the previous or next screen.

To select Picture Mode

SETTINGS

PICTURE

Picture Mode

Select the picture mode optimized for the viewing

environment or the program.

• Vivid Heightens contrast, brightness, and

sharpness to display vivid images.

• Standard Displays images in standard levels of

contrast, brightness and sharpness.

• APS APS (Auto power saving) mode reduces

power consumption by dimming control.

• Cinema / Sport / Game Displays the optimum

picture for movie, sport, or game.

• Expert Menu for adjusting picture quality that

allows experts and amateurs to enjoy the best TV

viewing. This menu for adjustment is provided

for ISF-certified picture tuning professionals.

(ISF logo can be used only on ISF-certified TVs.)

ISFccc: Imaging Science Foundation Certified

Calibration Control

• Depending upon the input signal, the available

range of picture modes may differ.

• Expert mode is for picture tuning professionals

to control and fine-tune using a specific image.

For normal images, the effects may not be

drastic.

Changes the image mode.

Shows information on the current program.

Changes the sound mode.

Accesses the main menu.

Accesses the quick menu.

To Use Energy Saving Feature

Navigation button (up/down/left/right) Scrolls through

menus or options.

SETTINGS

PICTURE

Energy Saving

Selects menus or options and confirms your input.

Returns to the previous screen.

Reduces power consumption by adjusting peak

screen brightness.

• Off Turns off the Energy Saving.

• Minimum / Medium / Maximum Applies the

pre-set Energy Saving.

Clears all on-screen displays and returns to TV

viewing.

• Screen Off Screen is turned off and only sound

is played. Press any button on the remote control

to turn the screen back on.

Enables SAP (Secondary Audio Program) Feature.

Not functional.

Sets the length of time until the TV to turns off.

Control buttons (

) Controls the SIMPLINK

compatible devices (USB, SIMPLINK).

These access special functions in some

menus.

To use HDMI ULTRA HD Deep

Color (For UX340H series)

Specifications

Product specifications may be changed without

prior notice due to upgrade of product functions.

SETTINGS

PICTURE

HDMI ULTRA HD Deep

Color HDMI (1/2) ULTRA HD Deep Color

HDMI port provides ULTRA HD Deep Color,

You can watch more clear picture.

Television System

ATSC, NTSC-M, 64 & 256 QAM

• On ULTRA HD Deep Color support

• Off ULTRA HD Deep Color not support

• All HDMI ports support the HDCP 2.2.

• 4K Source is only supported in HDMI input.

• 4K signal and content are not available in

the RF/USB input.

Program Coverage

VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135,

CADTV 1-135

• All HDMI input ports support 4K @ 50/60 Hz

(4:4:4, 4:2:2) for high-definition video. Picture

or sound may not be supported depending

upon the specifications of the external device

connected. In that case, change the settings for

HDMI ULTRA HD Deep Color.

External Antenna Impedance

75 Ω

Environment Condition

• Operating Temperature

0 °C to 40 °C (32 °F to 104 °F)

• Operating Humidity

Less than 80 %

4K @ 60 Hz Support Format

Frame

Resolution rate

(Hz)

Color Depth / Chroma Sampling

• Storage Temperature

-20 °C to 60 °C (-4 °F to 140 °F)

• Storage Humidity

8 bit

10 bit

YCbCr 4:2:0¹

YCbCr 4:2:2¹

12 bit

YCbCr

4:2:0

Less than 85 %

3840 X

2160p

59.94

HDMI (PC) Supported Mode

YCbCr

4:4:4¹

60.00

4096 X

2160p

Horizontal

Vertical

Resolution

640 x 350

720 x 400

640 x 480

Frequency (kHz) Frequency (Hz)

RGB

31.46

37.87

48.36

54.34

63.98

47.71

67.50

56.25

54.00

53.95

54.00

70.09

70.08

59.94

60.31

60.00

60.05

60.02

60.01

60.00

30.00

25.00

24.00

23.97

24.00

4:4:4¹

1 Supported when HDMI ULTRA HD Deep Color

is set to On.

800 x 600

1024 x 768

1152 x 864

1280 x 1024

1360 x 768

1920 x 1080

3840 x 2160

4096 x 2160

For UX340H series

RGB (PC) Supported Mode

Component Port Connecting

Information

Horizontal

Resolution

Vertical

Frequency (kHz) Frequency (Hz)

Component ports on the TV

P_B

P_R

640 x 350

720 x 400

640 x 480

800 x 600

1024 x 768

1152 x 864

1360 x 768

1280 x 1024

1920 x 1080

31.46

37.87

48.36

54.34

47.71

63.98

67.50

70.09

70.08

59.94

60.31

60.00

60.05

60.01

60.02

60.00

B-Y R-Y

Video output ports on DVD player

Component Supported Mode

Horizontal

Resolution

Vertical

Frequency (kHz) Frequency (Hz)

15.73

31.50

31.47

45.00

44.96

33.75

33.72

67.50

67.432

27.00

26.97

33.75

33.71

60.00

59.94

60.00

59.94

60.00

59.94

60.00

59.94

60.00

59.94

24.00

23.976

30.00

29.97

720 x 480i

HDMI (DTV) Supported Mode

720 x 480p

1280 x 720p

1920 x 1080i

Horizontal

Resolution

Vertical

Frequency (kHz) Frequency (Hz)

31.46

31.50

31.47

31.50

44.96

45.00

33.72

33.75

26.97

27.00

33.71

33.75

67.43

67.50

53.95

54.00

56.25

61.43

67.50

59.94

60.00

59.94

60.00

59.94

60.00

59.94

60.00

23.97

24.00

29.97

30.00

59.94

60.00

23.98

24.00

25.00

29.97

30.00

640 x 480p

720 x 480p

1280 x 720p

1920 x 1080i

1920 x 1080p

3840 x 2160p

My Media Supported Files

• Maximum data transfer rate: 20 Mbps (Mega bit

per second)

• External supported subtitle formats:

*.srt (SubRip), *.smi (SAMI), *.sub (SubViewer,

MicroDVD, DVDsubtitleSystem, SubIdx

(Vobsub)), *.ass/*.ssa (SubStation Alpha), *.txt

(TMplayer), *.psb (PowerDivX)

135.00

60.00

• Internal supported subtitle formats:

*.dat/*.mpg/*.mpeg/*.vob (DVD Subtitle),

*.ts/*.tp/*.m2ts (DVB Subtitle), *.mp4 (DVD

Subtitle, UTF-8 Plain Text), *.mkv (ASS, SSA,

UTF-8 Plain Text, Universal Subtitle Format,

VobSub, DVD Subtitle), *.divx/*.avi (XSUB¹,

XSUB+)

135.00

53.95

54.00

56.25

61.43

67.50

135.00

59.94

23.98

24.00

25.00

29.97

30.00

60.00

59.94

4096 x 2160p

XSUB¹Supports internal subtitles generated

from DivX6

For UX340H series

Supported Video Formats

Supported Audio Formats

• File type: mp3

• Maximum: 1,920 x 1,080 @ 30p (only Motion

JPEG 640 x 480 @ 30p)

[Bit rate] 32 Kbps - 320 Kbps

[Sample freq.] 16 kHz - 48 kHz

[Support] MPEG-1, MPEG-2, Layer2, Layer3

• File type: AAC

• .asf, .wmv

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4,

DivX5, DivX6, XViD, H.264/AVC, VC1(WMV3,

WVC1), MP43

[Audio] WMA Standard, WMA9(Pro), MP3, AAC,

AC3, MP3

• .divx, .avi

[Bit rate] Free Format

[Sample freq.] 8 kHz ~ 48 kHz

[Support] ADIF, ADTS

• File type: M4A

[Bit rate] Free Format

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4,

DivX5, DivX6, XViD, H.264/AVC

[Audio] HE-AAC, LPCM, ADPCM, MPEG-1 Layer1,

MPEG-1 Layer2, Dolby Digital, MPEG-1 Layer3

(MP3)

[Sample freq.] 8 kHz ~ 48 kHz

[Support] MPEG-4

• File type: WMA

[Bit rate] 128 Kbps ~ 320 Kbps

[Sample freq.] 8 kHz ~ 48 kHz

[Support] WMA7, WMA8, WMA9 Standard

• File type: WMA 10 Pro

[Bit rate] ~ 768 Kbps

• .ts, .trp, .tp, .mts, .m2ts

[Video] H.264/AVC, MPEG-2, AVS, VC1

[Audio] MPEG-1 Layer1, MPEG-1 Layer2, MPEG-1

Layer3 (MP3), Dolby Digital, Dolby Digital Plus,

AAC, HE-AAC

[Channel / Sample freq.]

M0: up to 2 Channel @ 48 kHz (Except LBR

mode),

• .vob

M1: up to 5.1 Channel @ 48 kHz,

M2: up to 5.1 Channel @ 96 kHz

[Support] WMA 10 Pro

[Video] MPEG-1, MPEG-2

[Audio] Dolby Digital, MPEG-1 Layer1, MPEG-1

Layer2, DVD-LPCM

• File type: OGG

• .mp4, .m4v, .mov

[Bit rate] Free Format

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4,

DivX5, DivX6, XVID, H.264/AVC

[Audio] AAC, MPEG-1 Layer3 (MP3)

• .mkv

[Sample freq.] ~ 48 kHz

[Support] OGG Vorvis

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4,

DivX5, DivX6, XVID, H.264/AVC

[Audio] HE-AAC, Dolby Digital, MPEG-1 Layer3

(MP3), LPCM

Supported Photo Formats

• Category: 2D (jpeg, jpg, jpe)

[Available File type]

SOF0: Baseline,

• motion JPEG

SOF1: Extend Sequential,

[Video] MJPEG

SOF2: Progressive

[Audio] LPCM, ADPCM

[Photo size] Minimum: 64 x 64,

Maximum: Normal Type: 15,360 (W) x 8,640 (H),

Progressive Type: 1,920 (W) x 1,440 (H)

• Category: BMP

• .mpg, .mpeg, .mpe

[Video] MPEG-1, MPEG-2

[Audio] MPEG-1 Layer1, MPEG-1 Layer2, Dolby

Digital, LPCM

[Photo size] Minimum: 64 x 64, Maximum: 9,600

x 6,400

• Category: PNG

[Available file type] Interlace, Non-Interlace

[Photo size] Minimum: 64 x 64

Maximum: Interlace: 1,200 x 800

Non-Interlace: 9,600 x 6,400

• BMP and PNG format files may be slower to

display than JPEG.

• .dat

[Video] MPEG-1, MPEG-2

[Audio] MP2

• .flv

[Video] Sorenson H.263, H.264/AVC

[Audio] MP3, AAC, HE-AAC

• .3gp, .3gp2

[Video] H.264/AVC, MPEG-4 Part2

[Audio] AAC, AMR(NB/WB)

*DTS / *rm / *rmvb : Depending upon model

Open Source Software Notice

Information

To obtain the source code under GPL, LGPL, MPL,

and other open source licenses, that is contained

in this product, please visit http://opensource.lge.

com.

Licenses

Supported licenses may differ by model.

For more information about licenses,

visit www.lg.com.

In addition to the source code, all referred license

terms, warranty disclaimers and copyright notices

are available for download.

LG Electronics will also provide open source code

to you on CD-ROM for a charge covering the cost

of performing such distribution (such as the cost of

media, shipping, and handling) upon email request

to [email protected]. This offer is valid for three

(3) years from the date on which you purchased

the product

Manufactured under license from Dolby

Laboratories.

Dolby and the double-D symbol are trademarks

of Dolby Laboratories.

The terms HDMI and HDMI High-Definition

Multimedia Interface, and the HDMI logo are

trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other

countries.

Troubleshooting

The software may be updated for improvement

in performance. The customer is responsible to

ensure the compatibility of their equipment with

any LG Electronics software. If needed, please

consult with LG Electronics and update new

software versions according to the guidance

provided by LG Electronics.

• Cannot control the TV with the remote control.

- Check if anything such as tape has been placed

over the receiver.

- Check if there is any obstacle between the

product and the remote control.

- Replace the batteries with new fresh ones.

• No image display and no sound is produced.

- Check if the product is turned on.

- Check if the power cord is connected to a wall

outlet.

This DivX Certified® device has passed rigorous

testing to ensure it plays DivX® video. To play

purchased DivX movies, first register your device

at vod.divx.com. Find your registration code in

the DivX VOD section of your device setup menu.

DivX Certified® to play DivX® video up to HD

1080p, including premium content. DivX®, DivX

Certified® and associated logos are trademarks of

DivX, LLC and are used under license.

Covered by DivX Patents 7,295,673; 7,515,710;

RE45,052; and others available at

[www.divx.com/patents]

- Check if there is a problem in the wall outlet by

connecting other products.

• The TV turns off suddenly.

- Check the power control settings.

The power supply may be interrupted.

- Check if the Off Time / Sleep Timer feature is

activated in the TIME settings.

- If there is no signal while the TV is on, the TV

will turn off automatically after 15 minutes of

inactivity.

For DTS patents, see http://patents.dts.com.

Manufactured under license from DTS Licensing

Limited. DTS, the Symbol, & DTS and the Symbol

together are registered trademarks,

and DTS 2.0+Digital Out is a trademark of DTS,

Key Codes

• This feature is not available for all models.

Code

(Hexa)

Function

(Hexa)

Note

Function

Note

CH / PAGE

VOL

R/C Button

Q.MENU

VOL

►

R/C Button

PICTURE

EXIT

R/C Button

◄

R/C Button

(POWER)

R/C Button

MUTE

INPUT

SLEEP

R/C Button

RATIO

►►

10 - 19 * Number Key 0 - 9

◄◄

FLASHBK

FAV

R/C Button

INFO

►

ꕗ

BACK

AV MODE

CAPTION

▲

ꕘ

AUDIO

SOUND

▼

SETTINGS

R/C Button

• Key code 4C (0x4C) is available on ATSC / ISDB models which use major/minor channel.

(For South Korea, Japan, North America, Latin America except Colombia models)

(Depending upon country)

External Control Device Setup

• Image shown may differ from your TV.

Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an

A/V control system) to control the product’s functions externally.

Note: The type of control port on the TV can be different between model series.

• Please be advised that not all models support this type of connectivity.

• Cable is not provided.

USB to Serial Converter with USB Cable

USB Type

(TV)

(PC)

• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter which is

not made nor provided by LG.

• It can be purchased from computer stores that carry accessories for IT support professionals.

RS-232C With RS232C Cable

DE9 (D-Sub 9-pin) Type

• You need to purchase the RS-232C (DE9, D-Sub 9-pin female-to-female type) to RS-232C cable required for

the connection between the PC and the TV, which is specified in the manual.

• The connection interface may differ from your TV.

RS-232C IN

(CONTROL & SERVICE)

(PC)

(TV)

Phone jack Type

• You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and the

TV, which is specified in the manual.

• For other models, connect to the USB port.

• The connection interface may differ from your TV.

(PC)

(TV)

- or

(PC)

RS-232C IN

(CONTROL & SERVICE)

Customer Computer

RS-232C Configurations

7-Wire Configuration

(Serial female-female NULL modem cable)

RXD

TXD

GND

DTR

DSR

RTS

CTS

TXD

RXD

GND

DSR

DTR

CTS

RTS

RS-232C

(Serial port)

D-Sub 9

3-Wire Configurations (Not standard)

RXD

TXD

GND

DTR

DSR

RTS

CTS

TXD

RXD

GND

DSR

DTR

CTS

RTS

D-Sub 9

Set ID

For Set ID number, see Real Data Mapping.

1. Press SETTINGS to access the main menus.

2. Press the navigation buttons to scroll to (General → About this TV or OPTION) and press OK.

3. Press the navigation buttons to scroll to SET ID and press OK.

4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.

5. When you are finished, press EXIT.

* (Depending upon model)

Communication Parameters

• Baud rate : 9600 bps (UART)

• Data length : 8 bits

• Parity : None

• Stop bit : 1 bit

• Communication code : ASCII code

• Use a crossed (reverse) cable.

Command Reference List

(Depending upon model)

DATA

(Hexadecimal)

DATA

(Hexadecimal)

COMMAND1 COMMAND2

01. Power*

00 to 01

15. Balance

00 to 64

16. Color

(Colour)

02. Aspect Ratio

(page 24)

Temperature

17. ISM Method

(Only Plasma TV)

03. Screen Mute

04. Volume Mute

(page 24)

00 to 01

00 to 64

(page 26)

00 to 05

18. Equalizer

05. Volume

Control

19. Energy

Saving

20. Tune

Command

06. Contrast

00 to 64

(page 26)

00 to 01

21. Channel

(Programme)

Add/Del(Skip)

22. Key

07. Brightness

00 to 64

08. Color/Colour

Key Codes

00 to 64

23. Control

Backlight,

Control Panel

Light

09. Tint

00 to 64

24. Input select

(Main)

(page 28)

(page 29)

10. Sharpness

11. OSD Select

00 to 32

00 to 01

25. 3D (Only 3D

models)

26. Extended

3D (Only 3D

models)

12. Remote

Control Lock

Mode

00 to 01

27. Auto

Configure

(page 29)

13. Treble

14. Bass

00 to 64

* Note:

During playing or recording media, all commands except Power (ka) and Key (mc) are not executed

and treated as NG.

With RS232C cable, TV can communicate ka command in power-on or power-off status. but with

USB-to-Serial converter cable, the command works only if TV is on.

Transmission / Receiving Protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

[Command1]

[Command2]

[Set ID]

First command to control the TV. (j, k, m or x)

Second command to control the TV.

You can adjust the [Set ID] to choose desired monitor ID number in option menu.

Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set

can be controlled.

* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on

transmission/receiving protocol.

[Data]

[Cr]

To transmit command data (hexadecimal). Transmit ‘FF’data to read status of command.

Carriage Return - ASCII code ‘0x0D’

[

]

Space – ASCII code ‘0x20’

OK Acknowledgement

[Command2][ ][Set ID][ ][OK][Data][x]

The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the

data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the

PC computer.

Error Acknowledgement

[Command2][ ][Set ID][ ][NG][Data][x]

The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from

non-viable functions or communication errors.

Data 00 : Illegal Code

Real Data Mapping (Hexadecimal : Decimal)

• When you enter the [data] in hexadecimal, refer to following conversion table.

• Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.

00 : Step 0

32 : Step 50 (Set ID 50)

FE : Step 254

FF : Step 255

01 : Step 1 (Set ID 1)

33 : Step 51 (Set ID 51)

...

0A : Step 10 (Set ID 10)

63 : Step 99 (Set ID 99)

01 00 : Step 256

...

0F : Step 15 (Set ID 15)

10 : Step 16 (Set ID 16)

...

C7 : Step 199

C8 : Step 200

...

27 0E : Step 9998

27 0F : Step 9999

...

• Commands may work differently depending upon model and signal.

01. Power (Command: k a)

03. Screen Mute (Command: k d)

▶ To control Power *On or Off of the set.

Transmission[k][a][ ][Set ID][ ][Data][Cr]

▶ To select screen mute on/off.

Transmission [k][d][ ][Set ID][ ][Data][Cr]

Data 00 : Screen mute off (Picture on)

Video mute off

Data 00 : Power Off

01 : *Power On

01 : Screen mute on (Picture off)

10 : Video mute on

Ack [a][ ][Set ID][ ][OK/NG][Data][x]

▶ To Show TV is Power On or *Off

Ack [d][ ][Set ID][ ][OK/NG][Data][x]

Transmission [k][a][ ][Set ID][ ][FF][Cr]

In case of video mute on only, TV will display On

Screen Display(OSD). But, in case of Screen mute

on, TV will not display OSD.

Ack [a][ ][Set ID][ ][OK][Data][x]

Similarly, if other functions transmit ‘FF’ data

based on this format, Acknowledgement feedback

presents status about each function.

04. Volume Mute (Command: k e)

▶ To control volume mute on/off.

You can also adjust mute using the MUTE button

on remote control.

02. Aspect Ratio (Command: k c)

(Main Picture Size)

Transmission [k][e][ ][Set ID][ ][Data][Cr]

▶ To adjust the screen format. (Main picture format)

You can also adjust the screen format using the

Aspect Ratio in the Q.MENU or PICTURE menu.

Data 00 : Volume mute on (Volume off)

01 : Volume mute off (Volume on)

Ack [e][ ][Set ID][ ][OK/NG][Data][x]

Transmission [k][c][ ][Set ID][ ][Data][Cr]

Data 01 : Normal screen (4:3) 07 : 14:9

02 : Wide screen(16:9) (Europe, Colombia, Mid-

04 : Zoom

05 : Zoom 2

East, Asia except South

Korea and Japan)

05. Volume Control (Command: k f)

▶ To adjust volume.

(Latin America except

Colombia Only)

06 : Set by Program/

Original

09 : * Just Scan

0B : Full Wide

You can also adjust volume with the volume

buttons on remote control.

(Europe, Colombia, Mid-

East, Asia except South

Korea and Japan)

10 to 1F : Cinema Zoom

1 to 16

Transmission [k][f][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

Ack [f][ ][Set ID][ ][OK/NG][Data][x]

Ack [c][ ][Set ID][ ][OK/NG][Data][x]

• Using the PC input, you select either 16:9 or 4:3

screen aspect ratio.

06. Contrast (Command: k g)

• In DTV/HDMI/Component mode (high-

definition), Just Scan is available.

• Full wide mode may work differently based on

model and is supported for DTV fully, and ATV,

AV partially.

▶ To adjust screen contrast.

You can also adjust contrast in the PICTURE

menu.

Transmission [k][g][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

Ack [g][ ][Set ID][ ][OK/NG][Data][x]

07. Brightness (Command: k h)

12. Remote control lock mode (Command: k m)

▶ To adjust screen brightness.

You can also adjust brightness in the PICTURE

menu.

▶ To lock the front panel controls on the monitor and

remote control.

Transmission [k][m][ ][Set ID][ ][Data][Cr]

Transmission [k][h][ ][Set ID][ ][Data][Cr]

Data 00 : Lock off

01 : Lock on

Data Min : 00 to Max : 64

Ack [m][ ][Set ID][ ][OK/NG][Data][x]

Ack [h][ ][Set ID][ ][OK/NG][Data][x]

If you are not using the remote control, use this

mode.

When main power is off for 30 seconds and

then restored, (plug-off and plug-in, after 20 - 30

seconds), external control lock is released.

08. Color/Colour (Command: k i)

▶ To adjust the screen Color(Colour).

You can also adjust colour in the PICTURE menu.

In the standby mode (DC off by off timer or ‘ka’, ‘mc’

command), and if key lock is on, TV will not turn on

by power on key of IR and Local Key.

Transmission [k][i][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

Ack [i][ ][Set ID][ ][OK/NG][Data][x]

13. Treble (Command: k r)

▶ To adjust treble.

You can also adjust in the AUDIO menu.

Transmission [k][r][ ][Set ID][ ][Data][Cr]

09. Tint (Command: k j)

▶ To adjust the screen tint.

Data Min : 00 to Max : 64

You can also adjust tint in the PICTURE menu.

Ack [r][ ][Set ID][ ][OK/NG][Data][x]

Transmission [k][j][ ][Set ID][ ][Data][Cr]

* (Depending upon model)

14. Bass (Command: k s)

Data Red : 00 to Green : 64

Ack [j][ ][Set ID][ ][OK/NG][Data][x]

▶ To adjust Bass.

You can also adjust in the AUDIO menu.

10. Sharpness (Command: k k)

Transmission [k][s][ ][Set ID][ ][Data][Cr]

▶ To adjust the screen sharpness.

You can also adjust sharpness in the PICTURE

menu.

Data Min : 00 to Max : 64

Ack [s][ ][Set ID][ ][OK/NG][Data][x]

Transmission [k][k][ ][Set ID][ ][Data][Cr]

* (Depending upon model)

15. Balance (Command: k t)

Data Min : 00 to Max : 32

Ack [k][ ][Set ID][ ][OK/NG][Data][x]

▶ To adjust balance.

You can also adjust balance in the AUDIO menu.

11. OSD Select (Command: k l)

Transmission [k][t][ ][Set ID][ ][Data][Cr]

▶ To select OSD (On Screen Display) on/off when

controlling remotely.

Data Min : 00 to Max : 64

Transmission [k][l][ ][Set ID][ ][Data][Cr]

Ack [t][ ][Set ID][ ][OK/NG][Data][x]

Data 00 : OSD off

01 : OSD on

Ack [l][ ][Set ID][ ][OK/NG][Data][x]

16. Color(Colour) Temperature (Command: x u)

19. Energy Saving (Command: j q)

▶ To adjust colour temperature. You can also adjust

▶ To reduce the power consumption of the TV. You

Color(Colour) Temperature in the PICTURE menu.

can also adjust Energy Saving in PICTURE menu.

Transmission [x][u][ ][Set ID][ ][Data][Cr]

Transmission [j][q][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

Data

00 : Off

Ack [u][ ][Set ID][ ][OK/NG][Data][x]

01 : Minimum

02 : Medium

03 : Maximum

04 : Auto (For LCD TV / LED TV) /

Intelligent sensor (For PDP TV)

05 : Screen off

17. ISM Method (Command: j p) (Only Plasma TV)

▶ To control the ISM method. You can also adjust

ISM Method in OPTION menu.

(Depending upon model)

Transmission [j][p][ ][Set ID][ ][Data][Cr]

Ack [q][ ][Set ID][ ][OK/NG][Data][x]

Data Min : 02: Orbiter

08: Normal

20: Color(Colour) Wash

20. Tune Command (Command: m a)

Ack [p][ ][Set ID][ ][OK/NG][Data][x]

This command may work differently depending

upon model and signal.

•

For Europe, Mid-East, Colombia, Asia except South

Korea and Japan Model

18. Equalizer (Command : j v)

▶ Adjust EQ of the set.

▶ Select channel to following physical number.

Transmission [m][a][ ][Set ID][ ][Data 00][ ]

[Data 01][ ][Data 02][Cr]

Transmission [j][v][ ][Set ID][ ][Data][Cr]

MSB

LSB

Analog Antenna/Cable

[Data 00][Data 01] Channel Data

Data 00 : High byte channel data

Data 01 : Low byte channel data

- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)

Frequency

Data

Data 02 : Input Source (Analog)

- 00 : Antenna TV (ATV)

Step

Frequency

1^stBand

2^ndBand

3^rdBand

4^thBand

5^thBand

0 (decimal)

1 (decimal)

...

19 (decimal)

20 (decimal)

- 80 : Cable TV (CATV)

Digital Antenna/Cable/Satellite

... ... ... ... ...

[Data 00][Data 01]: Channel Data

Data 00 : High Channel data

Data 01 : Low Channel data

- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)

Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]

* It depends on model, and can adjust when sound

mode is EQ adjustable value.

Data 02 : Input Source (Digital)

- 10 : Antenna TV (DTV)

- 20 : Antenna Radio (Radio)

- 40 : Satellite TV (SDTV)

- 50 : Satellite Radio (S-Radio)

- 90 : Cable TV (CADTV)

- a0 : Cable Radio (CA-Radio)

Tune Command Examples:

1. Tune to the Analog antenna (PAL) Channel 10.

Set ID = All = 00

Data 00 & 01 = Channel Data is 10 = 00 0a

Data 02 = Analog Antenna TV = 00

Result = ma 00 00 0a 00

2. Tune to the digital antenna (DVB-T) Channel 01.

Set ID = All = 00

- 22 : Antenna TV (DTV) – Don’t Use Physical

Channel Number

Data 00 & 01 = Channel Data is 1 = 00 01

Data 02 = Digital Antenna TV = 10

Result = ma 00 00 01 10

- 26 : Cable TV (CADTV) - Don’t Use Physical

Channel Number

- 46 : Cable TV (CADTV) – Use Major Channel

Number Only (One Part Channel)

Two bytes are available for each major and minor

channel data, but usually the low byte is used alone

(high byte is 0).

3. Tune to the satellite (DVB-S) Channel 1000.

Set ID = All = 00

Data 00 & 01 = Channel Data is 1000 = 03 E8

Data 02 = Digital Satellite TV = 40

Result = ma 00 03 E8 40

* Tune Command Examples:

1. Tune to the Analog cable (NTSC) channel 35.

Set ID = All = 00

Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]

[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]

Data 00 = Channel Data is 35 = 23

Data 01 & 02 = No Major = 00 00

Data 03 & 04 = No Minor = 00 00

Data 05 = Analog Cable TV = 01

Total = ma 00 23 00 00 00 00 01

•

For South Korea, North/Latin America except

Colombia Model

▶ To tune channel to following physical/major/minor

number.

2. Tune to the digital antenna (ATSC) channel 30-3.

Set ID = All = 00

Transmission [m][a][ ][0][ ][Data00][ ][Data01]

[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]

Data 00 = Don’t know Physical = 00

Data 01 & 02 = Major is 30 = 00 1E

Data 03 & 04 = Minor is 3 = 00 03

Data 05 = Digital Antenna TV = 22

Total = ma 00 00 00 1E 00 03 22

Digital channels have a Physical, Major, and Minor

channel number. The Physical number is the actual

digital channel number, the Major is the number that

the channel should be mapped to, and the Minor is

the sub-channel. Since the ATSC tuner automatically

maps the channel from the Major / Minor number,

the Physical number is not required when sending a

command in Digital.

Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]

[Data 02][Data 03][Data 04][Data 05]

[x][a][ ][Set ID][ ][NG][Data 00][x]

• For Japan Model

Analog Antenna/Cable

▶ To tune channel to following physical/major/minor

number.

Data 00 : Physical Channel Number

- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)

- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)

[Data 01 ~ 04]: Major/Minor Channel Number

Data 01 & 02: xx (Don't care)

Data 03 & 04: xx (Don't care)

Data 05: Input Source (Analog)

- 00 : Antenna TV (ATV)

Transmission [m][a][ ][0][ ][Data00][ ][Data01]

[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]

Digital Antenna / Satellite

Data 00: xx (Don't care)

[Data 01][Data 02]: Major Channel Number

Data 01: High byte Channel Data

Data 02: Low byte Channel Data

- 01 : Cable TV (CATV)

Digital Antenna/Cable

- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)

Data 00 : xx (Don't care)

[Data 03][Data 04]: Minor/Branch Channel Number

(Don’t care in Satellite)

Data 03: High byte Channel Data

Data 04: Low byte Channel Data

[Data 01][Data 02]: Major Channel Number

Data 01 : High byte Channel Data

Data 02 : Low byte Channel Data

- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)

[Data 03][Data 04]: Minor Channel Number

Data 03 : High byte Channel Data

Data 04 : Low byte Channel Data

Data 05 : Input Source (Digital)

- 02 : Antenna TV (DTV) – Use Physical Channel

Number

Data 05 : Input Source (Digital/Satellite for Japan)

- 02 : Antenna TV (DTV)

- 07 : BS (Broadcasting Satellite)

- 08 : CS1 (Communication Satellite 1)

- 09 : CS2 (Communication Satellite 2)

- 06 : Cable TV (CADTV) – Use Physical Channel

Number

Tune Command Examples:

•

For Plasma TV

Tune to the digital antenna (ISDB-T) channel 17-1

Set ID = All = 00

▶ To control the panel light.

Transmission [m][g][ ][Set ID][ ][Data][Cr]

Data 00 = Don’t know Physical = 00

Data 01 & 02 = Major is 17 = 00 11

Data 03 & 04 = Minor/Branch is 1 = 00 01

Data 05 = Digital Antenna TV = 02

Total = ma 00 00 00 11 00 01 02

Data Min : 00 to Max : 64

Ack [g][ ][Set ID][ ][OK/NG][Data][x]

2. Tune to the BS (ISDB-BS) channel 30.

Set ID = All = 00

Data 00 = Don’t know Physical = 00

Data 01 & 02 = Major is 30 = 00 1E

Data 03 & 04 = Don’t Care = 00 00

24. Input select (Command: x b)

(Main Picture Input)

▶ To select input source for main picture.

Transmission [x][b][ ][Set ID][ ][Data][Cr]

Data 05 = Digital BS TV = 07

Total = ma 00 00 00 1E 00 00 07

Data

00 : DTV

01 : CADTV

10 : ATV

This feature is varied based on the model.

Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]

[Data 02][Data 03][Data 04][Data 05]

[x][a][ ][Set ID][ ][NG][Data 00][x]

02 : Satellite DTV

ISDB-BS (Japan)

03 : ISDB-CS1 (Japan)

04 : ISDB-CS2 (Japan)

11 : CATV

20 : AV or AV1

21 : AV2

40 : Component1

60 : RGB

41 : Component2

21. Channel(Programme) Add/Del(Skip) (Command:

m b)

90 : HDMI1

92 : HDMI3

91 : HDMI2

93 : HDMI4

▶ To skip current channel(programme) for next time.

Transmission [m][b][ ][Set ID][ ][Data][Cr]

Ack [b][ ][Set ID][ ][OK/NG][Data][x]

Data 00 : Del(ATSC,ISDB)/Skip(DVB)

Ack [b][ ][Set ID][ ][OK/NG][Data][x]

01 : Add

This function depends on model and signal.

Set the saved channel status to del(ATSC, ISDB)/

skip(DVB) or add.

25. 3D(Command: x t) (only 3D models)

(Depending upon model)

▶ To change 3D mode for TV.

22. Key (Command: m c)

Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]

[ ][Data 02][ ][Data 03][Cr]

▶ To send IR remote key code.

Transmission [m][c][ ][Set ID][ ][Data][Cr]

* (Depending upon model)

Data Structure

[Data 00] 00 : 3D On

01 : 3D Off

Data Key code - page 19.

Ack [c][ ][Set ID][ ][OK/NG][Data][x]

02 : 3D to 2D

03 : 2D to 3D

[Data 01] 00 : Top and Bottom

01 : Side by Side

02 : Check Board

23. Control Backlight (Command: m g)

03 : Frame Sequential

04 : Column interleaving

05 : Row interleaving

•

For LCD TV / LED TV

▶ To control the backlight.

Transmission [m][g][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

Ack [g][ ][Set ID][ ][OK/NG][Data][x]

[Data 02] 00 : Right to Left

[Data 01] It has own range for each 3D option

determined by [Data 00].

1) When [Data 00] is 00

00 : Right to Left

01 : Left to Right

[Data 03] 3D Effect(3D Depth): Min : 00 - Max : 14

(*transmit by Hexadecimal code)

01 : Left to Right

If [Data 00] is 00 (3D On), [Data 03] has no

meaning.

2) When [Data 00] is 01, 02

If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data

01], [Data 02] and [Data 03] have no meaning.

Data

Min: 0 - Max: 14 (*transmit by Hexadecimal

code)

Data value range(0 - 20) converts Viewpoint range

(-10 - +10) automatically (Depending upon model)

* This option works when 3D Mode (Genre) is manual

only.

If [Data 00] is 03 (2D to 3D), [Data 01] and

[Data 02] have no meaning.

If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data

03] works when 3D Mode (Genre) is manual only.

All 3D pattern options ([Data 01]) may not be

available according to broadcasting/video signal.

3) When [Data 00] is 06, 07

00 : Off

01 : On

[Data 00]

[Data 01]

[Data 02]

[Data 03]

4) When [Data 00] is 08

00 : Revert to 3D video from 3D-to-2D

converted 2D video

01 : Change 3D video to 2D video, except

2D-to-3D video

* If conversion condition doesn’t meet, command is

treated as NG.

X : don’t care

5) When [Data 00] is 09

Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]

[Data03][x]

00 : Standard

02 : Cinema

04 : Manual

01 : Sport

03 : Extreme

05 : Auto

[t][ ][Set ID][ ][NG][Data00][x]

Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]

[v][ ][Set ID][ ][NG][Data00][x]

26. Extended 3D(Command: x v) (only 3D models)

(Depending upon model)

▶ To change 3D option for TV.

Transmission [x][v][ ][Set ID][ ][Data 00][ ]

[Data 01][Cr]

27. Auto Configure (Command: j u)

(Depending upon model)

▶ To adjust picture position and minimize image

shaking automatically. It works only in RGB (PC)

mode.

[Data 00] 3D option

00 : 3D Picture Correction

01 : 3D Depth (3D Mode is Manual Only)

02 : 3D Viewpoint

06 : 3D Color Correction

07 : 3D Sound Zooming

08 : Normal Image View

09 : 3D Mode (Genre)

Transmission [j][u][ ][Set ID][ ][Data][Cr]

Data 01 : To set

Ack [u][ ][Set ID][ ][OK/NG][Data][x]

CHILD SAFETY:

PROPER TELEVISION PLACEMENT MATTERS

THE CONSUMER ELECTRONICS INDUSTRY CARES

• Manufacturers, retailers and the rest of the consumer electronics industry are committed to

making home entertainment safe and enjoyable.

• As you enjoy your television, please note that all televisions – new and old- must be supported on

proper stands or installed according to the manufacturer’s recommendations. Televisions that

are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, carts, etc.,

may fall over, resulting in injury.

TUNE IN TO SAFETY

• ALWAYS follow the manufacturer’s recommendations for the safe installation of your television.

• ALWAYS read and follow all instructions for proper use of your television.

• NEVER allow children to climb on or play on the television or the furniture on which the television

is placed.

• NEVER place the television on furniture that can easily be used as steps, such as a chest of

drawers.

• ALWAYS install the television where it cannot be pushed, pulled over or knocked down.

• ALWAYS route cords and cables connected to the television so that they cannot be tripped

over, pulled or grabbed.

WALL OR CEILING MOUNT YOUR TELEVISION

• ALWAYS contact your retailer about professional installation if you have any doubts about your

ability to safely mount your television.

• ALWAYS use a mount that has been recommended by the television manufacturer and has a

safety certiﬁcation by an independent laboratory (such as UL, CSA, ETL).

• ALWAYS follow all instructions supplied by the television and mount manufacturers.

• ALWAYS make sure that the wall or ceiling where you are mounting the television is appropriate.

Some mounts are not designed to be mounted to walls and ceilings with steel studs or cinder

block construction. If you are unsure, contact a professional installer.

• Televisions can be heavy. A minimum of two people is required for a wall or ceiling mount

installation.

MOVING AN OLDER TELEVISION TO A NEW PLACE IN

YOUR HOME

• Many new television buyers move their older CRT televisions into a secondary room after the

purchase of a ﬂat-panel television. Special care should be made in the placement of older CRT

televisions.

• ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its size

and weight.

• NEVER place your older CRT television on a dresser where children may be tempted to use the

drawers to climb.

• ALWAYS make sure your older CRT television does not hang over the edge of your furniture.

CE.org/safety

Declaration of Conformity

Trade Name: LG

Model: 32LX340H-UA, 40LX340H-UA, 43LX340H-UA,

49LX340H-UA, 55LX340H-UA, 43UX340H-UA,

49UX340H-UA, 55UX340H-UA, 65UX340H-UA,

32LX340H-UF, 40LX340H-UF, 43LX340H-UF,

49LX340H-UF, 55LX340H-UF

Responsible Party: LG Electronics Inc.

Address: 1000 Sylvan Ave. Englewood Cliffs NJ 07632 U.S.A

TEL: 201-266-2534

The model and serial numbers of the TV are located on

the back and on one side of the TV. Record them below

should you ever need service.

LG Customer Information Center

For inquires or comments, visit www.lg.com or call;

1-888-865-3026

1-855-286-2456

USA, Commercial User

CANADA

MODEL

SERIAL

OWNER’S MANUAL

EXTERNAL CONTROL

DEVICE SETUP

Please read this manual carefully before operating the set and retain it for

future reference.

www.lg.com

KEY CODES

• This feature is not available for all models.

Code

(Hexa)

Code

(Hexa)

Function

CH +, PR +

Note

Function

Note

R/C Button

List

R/C Button

CH -, PR -

Volume +

Exit

PIP(AD)

Blue

Volume -

> (Arrow Key / Right Key)

< (Arrow Key / Left Key)

Power

Yellow

Green

Red

Mute

Ratio / Aspect Ratio

AD (Audio Description)

LIVE MENU

Input

SLEEP

TV, TV/RAD

User Guide

10 - 19 * Number Key 0 - 9

Smart / Home

SIMPLINK

Q.View / Flashback

FAV (Favorite Channel)

Text (Teletext)

►► (Forward)

◄◄ (Rewind)

Info

T. Opt (Teletext Option)

Return (BACK)

Program Guide

► (Play)

AV (Audio / Video) Mode

Caption/Subtitle

ꕗ (Stop / File List)

RECENT

(Arrow Key / Cursor Up)

V (Arrow Key / Cursor

Down)

ꕘ (Freeze / Slow Play /

R/C Button

Pause)

My Apps

R/C Button

Soccer

ꔄ (REC)

R/C Button

Menu / Settings

OK / Enter

Q.Menu

AutoConfig

App / *

TV / PC

List, - (ATSC Only)

PICTURE

SOUND

* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.

(For South Korea, Japan, North America, Latin America except Colombia models)

EXTERNAL CONTROL DEVICE SETUP

• Image shown may differ from your TV.

Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer

or an A/V control system) to control the product’s functions externally.

Note: The type of control port on the TV can be different between model series.

* Please be advised that not all models support this type of connectivity.

* Cable is not provided.

USB to Serial converter with USB Cable

USB Type

(TV)

(PC)

• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter

which is not made nor provided by LG.

• It can be purchased from computer stores that carry accessories for IT support professionals.

RS-232C With RS232C Cable

DE9 (D-Sub 9pin) Type

• You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C cable required

for the connection between the PC and the TV, which is specified in the manual.

RS-232C IN

(CONTROL & SERVICE)

(PC)

(TV)

The connection interface may differ from your TV.

EXTERNAL CONTROL DEVICE SETUP

Phone jack Type

• You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and

the TV, which is specified in the manual.

* For other models, connect to the USB port.

* The connection interface may differ from your TV.

(PC)

(TV)

- or

(PC)

RS-232C IN

(CONTROL & SERVICE)

Customer Computer

RS-232C configurations

3-Wire Configurations(Not standard)

RXD

TXD

GND

TXD

RXD

GND

RXD

TXD

GND

TXD

RXD

GND

RS-232C

(Serial port)

D-Sub 9

Phone

Set ID

For Set ID number, see "Real Data Mapping" on p.6

1. Press SETTINGS to access the main menus.

2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.

3. Press the Navigation buttons to scroll to SET ID and press OK.

4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.

5. When you are finished, press EXIT.

* (Depending on model)

EXTERNAL CONTROL DEVICE SETUP

Communication Parameters

• Baud rate : 9600 bps (UART)

• Data length : 8 bits

• Parity : None

• Stop bit : 1 bit

• Communication code : ASCII code

• Use a crossed (reverse) cable.

Command reference list

(Depending on model)

DATA

(Hexadecimal)

DATA

(Hexadecimal)

COMMAND1 COMMAND2

01. Power*

00 to 01

15. Balance

00 to 64

16. Color

(Colour)

Temperature

02. Aspect

Ratio

(p.7)

00 to 64

(p.8)

17. ISM

Method (Only j

Plasma TV)

03. Screen

Mute

04. Volume

Mute

00 to 01

00 to 64

18. Equalizer j

(p.8)

05. Volume

Control

19. Energy

Saving

00 to 05

20. Tune

Command

06. Contrast

(p.9)

21. Channel

(Programme)

Add/Del(Skip)

00 to 01

07.

Brightness

00 to 64

08. Color/

Colour

22. Key

Key Codes

00 to 64

23. Control

Backlight,

Control Panel

Light

09. Tint

00 to 64

10.

Sharpness

24. Input

select (Main)

(p.11)

(p.12)

00 to 32

00 to 01

11. OSD

Select

25. 3D (Only

3D models)

12. Remote

Control Lock

Mode

26. Extended x

3D (Only 3D

models)

00 to 01

00 to 64

27. Auto

Configure

(p.12)

13. Treble

14. Bass

* Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not

executed and treated as NG.

With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with

USB-to-Serial converter cable, the command works only if TV is on.

EXTERNAL CONTROL DEVICE SETUP

Transmission / Receiving Protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

[Command 1] : First command to control the TV. (j, k, m or x)

[Command 2] : Second command to control the TV.

[Set ID]

: You can adjust the [Set ID] to choose desired monitor ID number in option menu.

Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set

can be controlled.

* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on

transmission/receiving protocol.

[DATA]

[Cr]

: To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.

: Carriage Return - ASCII code ‘0x0D’

[ ]

: Space – ASCII code ‘0x20’

OK Acknowledgement

[Command2][ ][Set ID][ ][OK][Data][x]

* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,

if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the

data of the PC computer.

Error Acknowledgement

[Command2][ ][Set ID][ ][NG][Data][x]

* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from

non-viable functions or communication errors.

Data 00: Illegal Code

Real data mapping (Hexadecimal b Decimal)

* When you enter the [data] in hexadecimal, refer to following conversion table.

* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.

00 : Step 0

01 : Step 1 (Set ID 1)

32 : Step 50 (Set ID 50)

33 : Step 51 (Set ID 51)

FE : Step 254

FF : Step 255

...

0A : Step 10 (Set ID 10)

63 : Step 99 (Set ID 99)

01 00 : Step 256

...

0F : Step 15 (Set ID 15)

10 : Step 16 (Set ID 16)

...

C7 : Step 199

C8 : Step 200

...

27 0E : Step 9998

27 0F : Step 9999

...

EXTERNAL CONTROL DEVICE SETUP

* Commands may work differently depending on model and signal.

01. Power (Command: k a)

Ack [d][ ][Set ID][ ][OK/NG][Data][x]

► To control Power *On or Off of the set.

Transmission[k][a][ ][Set ID][ ][Data][Cr]

* In case of video mute on only, TV will display On

Screen Display(OSD). But, in case of Screen mute

on, TV will not display OSD.

Data 00 : Power Off

01 : *Power On

Ack [a][ ][Set ID][ ][OK/NG][Data][x]

04. Volume Mute (Command: k e)

► To Show TV is Power On or *Off

Transmission [k][a][ ][Set ID][ ][FF][Cr]

Ack [a][ ][Set ID][ ][OK][Data][x]

► To control volume mute on/off.

You can also adjust mute using the MUTE button

on remote control.

Transmission [k][e][ ][Set ID][ ][Data][Cr]

* Similarly, if other functions transmit ‘FF’ data

based on this format, Acknowledgement feedback

presents status about each function.

Data 00 : Volume mute on (Volume off)

01 : Volume mute off (Volume on)

Ack [e][ ][Set ID][ ][OK/NG][Data][x]

02. Aspect Ratio (Command: k c)

(Main Picture Size)

05. Volume Control (Command: k f)

► To adjust the screen format. (Main picture format)

You can also adjust the screen format using the

Aspect Ratio in the Q.MENU. or PICTURE menu.

► To adjust volume.

You can also adjust volume with the volume

buttons on remote control.

Transmission [k][f][ ][Set ID][ ][Data][Cr]

Transmission [k][c][ ][Set ID][ ][Data][Cr]

Data 01 : Normal screen 07 : 14:9

Data Min : 00 to Max : 64

(4:3)

02 : Wide screen

(16:9)

(Europe, Colombia, Mid-East,

Asia except South Korea and

Japan)

Ack [f][ ][Set ID][ ][OK/NG][Data][x]

04 : Zoom

09 : * Just Scan

0B : Full Wide

(Europe, Colombia, Mid-

East, Asia except South

Korea and Japan)

06. Contrast (Command: k g)

05 : Zoom 2

(Latin America

except Colombia

Only)

► To adjust screen contrast.

You can also adjust contrast in the PICTURE

menu.

06 : Set by Program/ 10 to 1F : Cinema Zoom 1 to 16

Original 0c : 21:9 (Depending on model)

Transmission [k][g][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

Ack [c][ ][Set ID][ ][OK/NG][Data][x]

Ack [g][ ][Set ID][ ][OK/NG][Data][x]

* Using the PC input, you select either 16:9 or 4:3

screen aspect ratio.

* In DTV/HDMI/Component mode (high-definition),

Just Scan is available.

07. Brightness (Command: k h)

► To adjust screen brightness.

You can also adjust brightness in the PICTURE

menu.

* Full wide mode may work differently based on

model and is supported for DTV fully, and ATV,

AV partially.

Transmission [k][h][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

03. Screen Mute (Command: k d)

► To select screen mute on/off.

Ack [h][ ][Set ID][ ][OK/NG][Data][x]

Transmission [k][d][ ][Set ID][ ][Data][Cr]

08. Color/Colour (Command: k i)

Data 00 : Screen mute off (Picture on)

Video mute off

► To adjust the screen Color(Colour).

01 : Screen mute on (Picture off)

10 : Video mute on

You can also adjust colour in the PICTURE menu.

Transmission [k][i][ ][Set ID][ ][Data][Cr]

EXTERNAL CONTROL DEVICE SETUP

Data Min : 00 to Max : 64

Ack [i][ ][Set ID][ ][OK/NG][Data][x]

Ack [r][ ][Set ID][ ][OK/NG][Data][x]

* (Depending on model)

09. Tint (Command: k j)

► To adjust the screen tint.

14. Bass (Command: k s)

You can also adjust tint in the PICTURE menu.

► To adjust Bass.

Transmission [k][j][ ][Set ID][ ][Data][Cr]

You can also adjust in the AUDIO menu.

Data Red : 00 to Green : 64

Transmission [k][s][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

Ack [j][ ][Set ID][ ][OK/NG][Data][x]

Ack [s][ ][Set ID][ ][OK/NG][Data][x]

10. Sharpness (Command: k k)

* (Depending on model)

► To adjust the screen sharpness.

You can also adjust sharpness in the PICTURE

menu.

15. Balance (Command: k t)

► To adjust balance.

You can also adjust balance in the AUDIO menu.

Transmission [k][k][ ][Set ID][ ][Data][Cr]

Transmission [k][t][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 32

Data Min : 00 to Max : 64

Ack [k][ ][Set ID][ ][OK/NG][Data][x]

Ack [t][ ][Set ID][ ][OK/NG][Data][x]

11. OSD Select (Command: k l)

16. Color(Colour) Temperature (Command: x u)

► To select OSD (On Screen Display) on/off when

controlling remotely.

► To adjust colour temperature. You can also adjust

Color(Colour) Temperature in the PICTURE menu.

Transmission [k][l][ ][Set ID][ ][Data][Cr]

Transmission [x][u][ ][Set ID][ ][Data][Cr]

Data 00 : OSD off

01 : OSD on

Data Min : 00 to Max : 64

Ack [l][ ][Set ID][ ][OK/NG][Data][x]

Ack [u][ ][Set ID][ ][OK/NG][Data][x]

12. Remote control lock mode (Command: k m)

17. ISM Method (Command: j p) (Only Plasma TV)

► To lock the front panel controls on the monitor and

► To control the ISM method. You can also adjust

remote control.

ISM Method in OPTION menu.

Transmission [k][m][ ][Set ID][ ][Data][Cr]

Transmission [j][p][ ][Set ID][ ][Data][Cr]

Data 00 : Lock off

01 : Lock on

Data Min : 02: Orbiter

08: Normal

Ack [m][ ][Set ID][ ][OK/NG][Data][x]

20: Color(Colour) Wash

* If you are not using the remote control, use this

mode.

Ack [p][ ][Set ID][ ][OK/NG][Data][x]

When main power is off & on (plug-off and plug-in,

after 20 - 30 seconds), external control lock is

released.

18. Equalizer (Command : j v)

* In the standby mode (DC off by off timer or ‘ka’,

‘mc’ command), and if key lock is on, TV will not

turn on by power on key of IR & Local Key.

► Adjust EQ of the set.

Transmission [j][v][ ][Set ID][ ][Data][Cr]

MSB

LSB

13. Treble (Command: k r)

► To adjust treble.

You can also adjust in the AUDIO menu.

Frequency

Data

Transmission [k][r][ ][Set ID][ ][Data][Cr]

EXTERNAL CONTROL DEVICE SETUP

Data 02 : Input Source (Digital)

- 10 : Antenna TV (DTV)

Frequency

1st Band

2nd Band

3rd Band

4th Band

5th Band

...

Step

0(decimal)

1(decimal)

...

- 20 : Antenna Radio (Radio)

- 40 : Satellite TV (SDTV)

- 50 : Satellite Radio (S-Radio)

- 90 : Cable TV (CADTV)

19(decimal)

20(decimal)

- a0 : Cable Radio (CA-Radio)

* Tune Command Examples:

1. Tune to the Analog antenna (PAL) Channel 10.

Set ID = All = 00

Data 00 & 01 = Channel Data is 10 = 00 0a

Data 02 = Analog Antenna TV = 00

Result = ma 00 00 0a 00

Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]

* It depends on model, and can adjust when sound

mode is EQ adjustable value.

19. Energy Saving (Command: j q)

► To reduce the power consumption of the TV. You

2. Tune to the digital antenna (DVB-T) Channel 01.

Set ID = All = 00

Data 00 & 01 = Channel Data is 1 = 00 01

Data 02 = Digital Antenna TV = 10

Result = ma 00 00 01 10

can also adjust Energy Saving in PICTURE menu.

Transmission [j][q][ ][Set ID][ ][Data][Cr]

Data

00 : Off

01 : Minimum

02 : Medium

03 : Maximum

04 : Auto (For LCD TV / LED TV) /

Intelligent sensor (For PDP TV)

05 : Screen off

3. Tune to the satellite (DVB-S) Channel 1000.

Set ID = All = 00

Data 00 & 01 = Channel Data is 1000 = 03 E8

Data 02 = Digital Satellite TV = 40

Result = ma 00 03 E8 40

Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]

[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]

* (Depending on model)

Ack [q][ ][Set ID][ ][OK/NG][Data][x]

• For South Korea, North/Latin America except

Colombia Model

► To tune channel to following physical/major/minor

20. Tune Command (Command: m a)

number.

* This command may work differently depending on

model and signal.

• For Europe, Mid-East, Colombia, Asia except

South Korea and Japan Model

Transmission [m][a][ ][0][ ][Data00][ ][Data01]

[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]

Digital channels have a Physical, Major, and Minor

channel number. The Physical number is the actual

digital channel number, the Major is the number that

the channel should be mapped to, and the Minor is

the sub-channel. Since the ATSC tuner automatically

maps the channel from the Major / Minor number,

the Physical number is not required when sending a

command in Digital.

► Select channel to following physical number.

Transmission [m][a][ ][Set ID][ ][Data 00][ ]

[Data 01][ ][Data 02][Cr]

* Analog Antenna/Cable

[Data 00][Data 01] Channel Data

Data 00 : High byte channel data

Data 01 : Low byte channel data

- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)

* Analog Antenna/Cable

Data 00 : Physical Channel Number

- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)

- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)

Data 02 : Input Source (Analog)

- 00 : Antenna TV (ATV)

- 80 : Cable TV (CATV)

[Data 01 ~ 04]: Major/Minor Channel Number

Data 01 & 02: xx (Don't care)

Data 03 & 04: xx (Don't care)

Data 05: Input Source (Analog)

- 00 : Antenna TV (ATV)

* Digital Antenna/Cable/Satellite

[Data 00][Data 01]: Channel Data

Data 00 : High Channel data

Data 01 : Low Channel data

- 01 : Cable TV (CATV)

- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)

EXTERNAL CONTROL DEVICE SETUP

* Digital Antenna/Cable

Data 00 : xx (Don't care)

* Digital Antenna/Satellite

Data 00: xx (Don't care)

[Data 01][Data 02]: Major Channel Number

Data 01: High byte Channel Data

Data 02: Low byte Channel Data

[Data 01][Data 02]: Major Channel Number

Data 01 : High byte Channel Data

Data 02 : Low byte Channel Data

- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)

[Data 03][Data 04]: Minor Channel Number

Data 03 : High byte Channel Data

Data 04 : Low byte Channel Data

- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)

[Data 03][Data 04]: Minor/Branch Channel Number

(Don’t care in Satellite)

Data 03: High byte Channel Data

Data 04: Low byte Channel Data

Data 05 : Input Source (Digital)

- 02 : Antenna TV (DTV) – Use Physical Channel

Number

Data 05 : Input Source (Digital/Satellite for Japan)

- 02 : Antenna TV (DTV)

- 06 : Cable TV (CADTV) – Use Physical Channel

Number

- 22 : Antenna TV (DTV) – Don’t Use Physical

Channel Number

- 07 : BS (Broadcasting Satellite)

- 08 : CS1 (Communication Satellite 1)

- 09 : CS2 (Communication Satellite 2)

- 26 : Cable TV (CADTV) - Don’t Use Physical

Channel Number

* Tune Command Examples:

Tune to the digital antenna (ISDB-T) channel 17-1

Set ID = All = 00

- 46 : Cable TV (CADTV) – Use Physical/Major

Channel Number Only (One Part Channel)

- 66 : Cable TV (CADTV) – Use Major Channel

Number Only (One Part Channel)

Two bytes are available for each major and minor

channel data, but usually the low byte is used alone

(high byte is 0).

Data 00 = Don’t know Physical = 00

Data 01 & 02 = Major is 17 = 00 11

Data 03 & 04 = Minor/Branch is 1 = 00 01

Data 05 = Digital Antenna TV = 02

Total = ma 00 00 00 11 00 01 02

2. Tune to the BS (ISDB-BS) channel 30.

Set ID = All = 00

Data 00 = Don’t know Physical = 00

Data 01 & 02 = Major is 30 = 00 1E

Data 03 & 04 = Don’t Care = 00 00

Data 05 = Digital BS TV = 07

* Tune Command Examples:

1. Tune to the Analog cable (NTSC) channel 35.

Set ID = All = 00

Data 00 = Channel Data is 35 = 23

Data 01 & 02 = No Major = 00 00

Data 03 & 04 = No Minor = 00 00

Data 05 = Analog Cable TV = 01

Total = ma 00 23 00 00 00 00 01

Total = ma 00 00 00 1E 00 00 07

* This feature is varied based on the model.

Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]

[Data 02][Data 03][Data 04][Data 05]

[x][a][ ][Set ID][ ][NG][Data 00][x]

2. Tune to the digital antenna (ATSC) channel 30-3.

Set ID = All = 00

Data 00 = Don’t know Physical = 00

Data 01 & 02 = Major is 30 = 00 1E

Data 03 & 04 = Minor is 3 = 00 03

Data 05 = Digital Antenna TV = 22

Total = ma 00 00 00 1E 00 03 22

21. Channel(Programme) Add/Del(Skip)

(Command: m b)

Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]

[Data 02][Data 03][Data 04][Data 05]

[x][a][ ][Set ID][ ][NG][Data 00][x]

► To skip current channel(programme) for next time.

Transmission [m][b][ ][Set ID][ ][Data][Cr]

• For Japan Model

► To tune channel to following physical/major/minor

Data 00 : Del(ATSC,ISDB)/Skip(DVB) 01 : Add

Ack [b][ ][Set ID][ ][OK/NG][Data][x]

number.

Transmission [m][a][ ][0][ ][Data00][ ][Data01]

[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]

* Set the saved channel status to del(ATSC, ISDB)/

skip(DVB) or add.

EXTERNAL CONTROL DEVICE SETUP

22. Key (Command: m c)

25. 3D(Command: x t) (only 3D models)

(Depending on model)

► To send IR remote key code.

Transmission [m][c][ ][Set ID][ ][Data][Cr]

► To change 3D mode for TV.

Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]

Data Key code - p.2.

[ ][Data 02][ ][Data 03][Cr]

* (Depending on model)

Data Structure

Ack [c][ ][Set ID][ ][OK/NG][Data][x]

[Data 00] 00 : 3D On

01 : 3D Off

23. Control Backlight (Command: m g)

• For LCD TV / LED TV

► To control the backlight.

02 : 3D to 2D

03 : 2D to 3D

[Data 01] 00 : Top and Bottom

01 : Side by Side

Transmission [m][g][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

02 : Check Board

03 : Frame Sequential

04 : Column interleaving

05 : Row interleaving

[Data 02] 00 : Right to Left

01 : Left to Right

Ack [g][ ][Set ID][ ][OK/NG][Data][x]

Control Panel Light (Command: m g)

• For Plasma TV

► To control the panel light.

[Data 03] 3D Effect(3D Depth): Min : 00 - Max : 14

(*transmit by Hexadecimal code)

Transmission [m][g][ ][Set ID][ ][Data][Cr]

* [Data 02], [Data 03] functions depend on model

and signal.

Data Min : 00 to Max : 64

* If [Data 00] is 00 (3D On), [Data 03] has no

meaning.

Ack [g][ ][Set ID][ ][OK/NG][Data][x]

* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data

01], [Data 02] and [Data 03] have no meaning.

24. Input select (Command: x b)

(Main Picture Input)

* If [Data 00] is 03 (2D to 3D), [Data 01] and

[Data 02] have no meaning.

► To select input source for main picture.

Transmission [x][b][ ][Set ID][ ][Data][Cr]

* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data

03] works when 3D Mode (Genre) is manual only.

Data

00 : DTV

01 : CADTV

10 : ATV

* All 3D pattern options ([Data 01]) may not be

available according to broadcasting/video signal.

02 : Satellite DTV

ISDB-BS (Japan)

03 : ISDB-CS1 (Japan)

04 : ISDB-CS2 (Japan)

11 : CATV

[Data 00]

[Data 01]

[Data 02]

[Data 03]

20 : AV or AV1

21 : AV2

40 : Component1

60 : RGB

41 : Component2

90 : HDMI1

92 : HDMI3

91 : HDMI2

93 : HDMI4

X : don’t care

Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]

[Data03][x]

Ack [b][ ][Set ID][ ][OK/NG][Data][x]

* This function depends on model and signal.

[t][ ][Set ID][ ][NG][Data00][x]

EXTERNAL CONTROL DEVICE SETUP

26. Extended 3D(Command: x v) (only 3D models)

(Depending on model)

27. Auto Configure (Command: j u)

(Depending on model)

► To change 3D option for TV.

Transmission [x][v][ ][Set ID][ ][Data 00][ ]

[Data 01][Cr]

► To adjust picture position and minimize image

shaking automatically. It works only in RGB (PC)

mode.

Transmission [j][u][ ][Set ID][ ][Data][Cr]

Data 01 : To set Auto Configure

[Data 00] 3D option

00 : 3D Picture Correction

01 : 3D Depth (3D Mode is Manual Only)

02 : 3D Viewpoint

Ack [u][ ][Set ID][ ][OK/NG][Data][x]

06 : 3D Color Correction

07 : 3D Sound Zooming

08 : Normal Image View

09 : 3D Mode (Genre)

[Data 01] It has own range for each 3D option

determined by [Data 00].

1) When [Data 00] is 00

00 : Right to Left

01 : Left to Right

2) When [Data 00] is 01, 02

Data

Min: 0 - Max: 14 (*transmit by Hexadecimal

code)

Data value range(0 - 20) converts Viewpoint range

(-10 - +10) automatically (Depending on model)

* This option works when 3D Mode (Genre) is manual

only.

3) When [Data 00] is 06, 07

00 : Off

01 : On

4) When [Data 00] is 08

00 : Revert to 3D video from 3D-to-2D

converted 2D video

01 : Change 3D video to 2D video, except

2D-to-3D video

* If conversion condition doesn’t meet, command is

treated as NG.

5) When [Data 00] is 09

00 : Standard

02 : Cinema

04 : Manual

01 : Sport

03 : Extreme

05 : Auto

Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]

[v][ ][Set ID][ ][NG][Data00][x]

EXTERNAL CONTROL DEVICE SETUP

Network IP Control

(For USA only)

How to connect

1. Connect your TV to a wired or wireless network.

2. Press and hold the

(Settings) button on the remote control for at least 5 seconds on the Live TV

screen. Once the Live TV channel banner appears at the top of the screen, enter 828 and press the OK

button to enter the ‘IP Control Setup’ menu.

* The 3-digit password (default password: 828) can be changed using Password Change.

3. After entering the ‘IP Control Setup’ menu, set the ‘Network IP Control’ submenu to ‘On’. The reboot

popup window will appear. Select ‘Yes’ to reboot your TV.

* Set to 'Off' when the feature is not in use.

4. Open a terminal program (e.g. putty, teraterm) on a computer and connect to your TV with your TV’s IP

address through telnet service and the port number 9761 as shown below.

ex) username : ~$ telnet 10.186.119.107 9761

5. If the connection is successful, the following message will appear. Or if ‘NG’ appears when you press

Enter, the connection has been established.

Trying 10.186.119.107...

Connected to 10.186.119.107.

Escape character is ' ^ ] ' .

6. Enter a command like the example shown below and press Enter.

VOLUME_MUTE on

7. If the command has been successfully entered, ‘OK’ will appear. If not, ‘NG’ will appear.

8. To exit the program, enter ‘quit’ and press Enter. Then, the following message will appear.

quit

Connection closed by foreign host

* Power ON through WOL(Wake On Lan)

You can turn on the TV, after setting the ‘Mobile TV On’ submenu(Setting > General > Mobile TV On) to

‘On’ and installing the app related with WOL(Wake On Lan) through iOS or Google Play on your mobile

phone.

EXTERNAL CONTROL DEVICE SETUP

Command reference list

COMMAND

NOTE

01. Power

POWER off

ex) POWER off

ASPECT_RATIO [4by3 /16by9 /

setbyoriginal]

02. Aspect Ratio

ex) ASPECT_RATIO 4by3

SCREEN_MUTE [screenmuteon /

videomuteon / allmuteoff]

03. Screen Mute

04. Volume Mute

05. Volume Control

ex) SCREEN_MUTE screenmuteon

ex) VOLUME_MUTE on

VOLUME_MUTE [on / off]

0 to 100 (Decimal)

ex) VOLUME_CONTROL 15

VOLUME_CONTROL [0 to 100]

0 to 100 (Decimal)

ex) PICTURE_CONTRAST 50

06. Contrast

07. Brightness

08. Color/Colour

09. Tint

PICTURE_CONTRAST [0 to 100]

PICTURE_BRIGHTNESS [0 to 100]

PICTURE_COLOUR [0 to 100]

PICTURE_TINT [0 to 100]

0 to 100 (Decimal)

ex) PICTURE_BRIGHTNESS 50

0 to 100 (Decimal)

ex) PICTURE_COLOUR 50

0 to 100 (Decimal)

ex) PICTURE_TINT 50

0 to 50 (Decimal)

ex) PICTURE_SHARPNESS 25

10. Sharpness

11. OSD Select

PICTURE_SHARPNESS [0 to 50]

OSD_SELECT [on / off]

ex) OSD_SELECT on

12. Remote Control

Lock Mode

REMOTECONTROLER_LOCK [on / off] ex) REMOTECONTROLER_LOCK on

0 to 100 (Decimal)

AUDIO_BALANCE [0 to 100]

13. Balance

ex) AUDIO_BALANCE 50

14. Color(Colour)

Temperature

PICTURE_COLOUR_TEMPERATURE 0 to 100 (Decimal)

[0 to 100]

ex) PICTURE_COLOUR_TEMPERATURE 50

1 to 5(Frequency band)

0 to 20(Step decimal)

15. Equalizer

AUDIO_EQUALIZER [1 to 5] [0 to 20]

* Precondition : All settings > sound > sound

mode settings > Equalizer on

ex) AUDIO_EQUALIZER 2 10

ENERGY_SAVING [screenoff / maximum

/ medium / minimum / off]

16. Energy Saving

ex) ENERGY_SAVING screenoff

CHANNEL_SETTING_ATSC_ATV

[Channel Number] antenna

CHANNEL_SETTING_ATSC_ATV

[Channel Number] cable

ex) CHANNEL_SETTING_ATSC_ATV 11

antenna

CHANNEL_SETTING_ATSC_DTV

[Channel Number] cablemaj

17. Tune Command

CHANNEL_SETTING_ATSC_DTV [Maj.

Channel Number] [Min.Channel Number]

antennanotphy

ex) CHANNEL_SETTING_ATSC_DTV 10 2

CHANNEL_SETTING_ATSC_DTV [Maj. antennanotphy

Channel Number] [Min.Channel Number]

cablenotphy

18.

Channel(Programme) CHANNEL_ADD_DELETE [add / delete] ex) CHANNEL_ADD_DELETE add

Add/Del

EXTERNAL CONTROL DEVICE SETUP

COMMAND

NOTE

KEY_ACTION [exit / channelup /

channeldown / volumeup / volumedown /

arrowright / arrowleft / volumemute

/ deviceinput / sleepreserve / livetv

/ previouschannel / favoritechannel /

teletext / teletextoption / returnback

/ avmode / captionsubtitle / arrowup /

arrowdown / myapp / settingmenu / ok /

quickmenu / videomode

/ audiomode / channellist / bluebutton /

yellowbutton / greenbutton / redbutton /

aspectratio / audiodescription

19. Key

ex) KEY_ACTION ok

/ programmorder / userguide /

smarthome / simplelink / fastforward /

rewind / programminfo / programguide

/ play / slowplay / soccerscreen / record /

3d / autoconfig / app / screenbright

/ number0 / number1 / number2 /

number3 / number4 / number5 / number6

/ number7 / number8 / number9]

0 to 100 (Decimal)

* Precondition : All settings > picture > Energy

Saving off

ex) PICTURE_BACKLIGHT 50

20. Control Backlight PICTURE_BACKLIGHT [0 to 100]

INPUT_SELECT [dtv / atv / cadtv / catv

21. Input select

/ avav1 / component1 / hdmi1 / hdmi2 / ex) INPUT_SELECT dtv

hdmi3]

PICTURE_3D [off / 3dto2d]

ex) PICTURE_3D off

PICTURE_3D 2dto3d [righttoleft /

lefttoright] [0 to 20]

ex) PICTURE_3D 2dto3d righttoleft 10

22. 3D (only 3D

models)

PICTURE_3D on [topandbottom

/ sidebyside / checkboard /

framesequential / columninterleaving /

rowinterleaving] [righttoleft / lefttoright] [0

to 20]

ex) PICTURE_3D on topandbottom righttoleft

EXTERNAL CONTROL DEVICE SETUP

COMMAND

NOTE

0 : Right to Left

1 : Left to Right

* Precondition :

1) PICTURE_3D on X X X

ex) PICTURE_3D_EXTENSION

picturecorrection 0

PICTURE_3D_EXTENSION

picturecorrection [0 / 1]

0 : off

1 : on

* Colorcorrection, Sound Precondition :

1) PICTURE_3D on X X X

Colorcorrection ex)

PICTURE_3D on topandbottom righttoleft 0

PICTURE_3D_EXTENSION colorcorrection 1

Sound ex)

PICTURE_3D_EXTENSION

[colorcorrection / sound] [0 / 1]

PICTURE_3D on topandbottom righttoleft 0

PICTURE_3D_EXTENSION sound 1

0 : off

1 : on

* Precondition :

PICTURE_3D_EXTENSION normal [0

23. Extended 3D (only / 1]

3D models)

1) PICTURE_3D on X X X

ex) PICTURE_3D_EXTENSION normal 0

0 to 20 : Viewpoint range

* Depth precondition :

1) PICTURE_3D 2dto3d X X

2) PICTURE_3D_EXTENSION genre 4

* Viewpoint precondition :

1) PICTURE_3D 2dto3d X X

Depth ex)

PICTURE_3D 2dto3d righttoleft 0

PICTURE_3D_EXTENSION genre 4

PICTURE_3D_EXTENSION depth 0

Viewpoint ex)

PICTURE_3D_EXTENSION

[depth / viewpoint] [0 to 20]

PICTURE_3D 2dto3d righttoleft 0

PICTURE_3D_EXTENSION viewpoint 0

0 : Standard / 1 : Sport / 2 : Cinema / 3 :

Extreme / 4 : Manual / 5 : Auto

* Precondition :

1) PICTURE_3D 2dto3d X X

ex) PICTURE_3D_EXTENSION genre 2

PICTURE_3D_EXTENSION genre [0 to

* This feature is varied based on the model.

* During playing or recording media, all commands except Power and Key commands are not executed and

treated as NG.

ENGLISH Easy Setup Guide

Please read this manual carefully before operating your set and retain it for future reference.

LED TV

32LX340H

40LX340H

43LX340H

49LX340H

55LX340H

ESPAÑOL Guía Rápida de Conﬁguración

Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para futuras consultas.

FRANÇAIS Guide de conﬁguration rapide

Avant d’utiliser l’appareil, veuillez lire attentivement ce manuel et le conserver pour pouvoir vous y reporter ultérieurement.

X 4

(M4 X L20)

X 6

(M4 X L20)

X 4

(M4 X L14)

43/49/55LX340H

32/40LX340H

43/49/55LX340H

X 2

www.lg.com

P/No : MFL68884962 (1612-REV01)

3-A ^32/40LX340H

43/49/55LX340H

32/40LX340H

43/49/55LX340H

4-B

3-B

4-A

ENGLISH

ESPAÑOL

FRANÇAIS

Image shown may differ from your TV.

La imagen puede ser diferente a la de su televisor.

Cette illustration peut ne pas correspondre à votre téléviseur.

32LX340H

(32LX340H-UA)

(32LX340H-UF)

40LX340H

(40LX340H-UA)

(40LX340H-UF)

43LX340H

(43LX340H-UA)

(43LX340H-UF)

ENGLISH

MODELS

734 x 489 x 282 (mm)

28.8 x 19.2 x 11.1 (inches)

734 x 438 x 55.3 (mm)

28.8 x 17.2 x 2.1 (inches)

8.2 kg (18.0 lbs)

911 x 576 x 282 (mm)

35.8 x 22.6 x 11.1 (inches)

911 x 528 x 55.3 (mm)

35.8 x 20.7 x 2.1 (inches)

10.4 kg (22.9 lbs)

973 x 624 x 325 (mm)

38.3 x 24.5 x 12.7 (inches)

973 x 573 x 37 (mm)

38.3 x 22.5 x 1.4 (inches)

13.6 kg (29.9 lbs)

With stand

Dimensions (W x H x D)

Without stand

With stand

Weight

Without stand

5.3 kg (11.6 lbs)

7.5 kg (16.5 lbs)

10.2 kg (22.4 lbs)

Power Requirement

AC 100 - 240 V ~ 50/60 Hz

0.9 A / 90 W

Current Value / Power Consumption

1.2 A / 70 W

1.0 A / 100 W

49LX340H

55LX340H

MODELS

(49LX340H-UA)

(49LX340H-UF)

(55LX340H-UA)

(55LX340H-UF)

1,106 x 701 x 325 (mm)

43.5 x 27.5 x 12.7 (inches)

1,106 x 647 x 37 (mm)

43.5 x 25.4 x 1.4 (inches)

17.8 kg (39.2 lbs)

1,242 x 780 x 325 (mm)

48.8 x 30.7 x 12.7 (inches)

1,242 x 724 x 37 (mm)

48.8 x 28.5 x 1.4 (inches)

21.1 kg (46.5 lbs)

With stand

Dimensions (W x H x D)

Without stand

With stand

Weight

Without stand

14.4 kg (31.7 lbs)

17.7 kg (39.0 lbs)

Power Requirement

AC 100 - 240 V ~ 50/60 Hz

Current Value / Power Consumption

1.2 A / 120 W

1.3 A / 130 W

ESPAÑOL

FRANÇAIS

MODELOS

MODÈLES

32LX340H

(32LX340H-UA)

(32LX340H-UF)

40LX340H

(40LX340H-UA)

(40LX340H-UF)

43LX340H

(43LX340H-UA)

(43LX340H-UF)

734 x 489 x 282 (mm)

28,8 x 19,2 x 11,1 (pulgadas / po)

734 x 438 x 55,3 (mm)

911 x 576 x 282 (mm)

35,8 x 22,6 x 11,1 (pulgadas / po)

911 x 528 x 55,3 (mm)

973 x 624 x 325 (mm)

38,3 x 24,5 x 12,7 (pulgadas / po)

973 x 573 x 37 (mm)

Con base

Dimensiones

(Ancho x altura x profundidad)

Avec support

Sin base

Dimensions (L x H x P)

28,8 x 17,2 x 2,1 (pulgadas / po)

35,8 x 20,7 x 2,1 (pulgadas / po)

38,3 x 22,5 x 1,4 (pulgadas / po)

Sans support

Con base

Avec support

Sin base

8,2 kg (18,0 libras / lb)

5,3 kg (11,6 libras / lb)

10,4 kg (22,9 libras / lb)

7,5 kg (16,5 libras / lb)

13,6 kg (29,9 libras / lb)

10,2 kg (22,4 libras / lb)

Peso

Poids

Sans support

Potencia requerida

Alimentation

Corriente de consumo / Consumo de la potencia

Valeur courante / Consommation électrique

AC 100-240 V ~ 50/60 Hz

0,9 A / 90 W

1,2 A / 70 W

1,0 A / 100 W

MODELOS

MODÈLES

49LX340H

(49LX340H-UA)

(49LX340H-UF)

55LX340H

(55LX340H-UA)

(55LX340H-UF)

1 106 x 701 x 325 (mm)

43,5 x 27,5 x 12,7 (pulgadas / po)

1 106 x 647 x 37 (mm)

1 242 x 780 x 325 (mm)

48,8 x 30,7 x 12,7 (pulgadas / po)

1 242 x 724 x 37 (mm)

Con base

Dimensiones

(Ancho x altura x profundidad)

Avec support

Sin base

Dimensions (L x H x P)

43,5 x 25,4 x 1,4 (pulgadas / po)

48,8 x 28,5 x 1,4 (pulgadas / po)

Sans support

Con base

Avec support

Sin base

17,8 kg (39,2 libras / lb)

14,4 kg (31,7 libras / lb)

21,1 kg (46,5 libras / lb)

17,7 kg (39,0 libras / lb)

Peso

Poids

Sans support

Potencia requerida

Alimentation

AC 100-240 V ~ 50/60 Hz

Corriente de consumo / Consumo de la potencia

Valeur courante / Consommation électrique

1,2 A / 120 W

1,3 A / 130 W

(For USA and Canada only)

(Para Estados Unidos y Canadá)

(Pour les États-Unis et le Canada)

Ce produit est conforme aux normes

This product qualifies for ENERGY STAR®

ENERGY STAR® lorsque le « réglage d’usine

par défaut (Résidentiel) » est sélectionné.

Modifier les réglages d’usine par défaut ou

in the factory default (Home configuration)

setting. Changing the factory default settings

or enabling other features may increase

activer d’autres fonctionnalités augmente

power consumption that could exceed the

limits necessary to quality for ENERGY STAR®. Refer to

ENERGYSTAR.gov for more information on the ENERGY

STAR® program.

la consommation d’énergie qui pourrait alors dépasser

les limites de la qualification ENERGY STAR®. Consultez

le site ENERGYSTAR.gov pour en savoir plus au sujet du

programme ENERGY STAR®.

Toshiba Ras 13ykv E User Manual
Panasonic Kx Tg4134 User Manual
Murphy Diesel Fuel Check Valves Ckv2336 User Manual
HITACHI 62VS69A User Manual
GE AET05 User Manual
EMERSON QUIET KOOL EARC18RE2 User Manual
DELL U2212HMC User Manual
CRAFTSMAN 678 29204 User Manual
BLACK DECKER KS900EL User Manual
ASUS X550Z User Manual