QUICK REFERENCE GUIDE
LED TV* / LCD TV
* LG LED TV applies LCD screen with LED backlights.
Please read this quick reference guide carefully
before operating your set and retain it for future reference.
LED TV MODELS
LCD TV MODELS
22LQ630H
26LQ630H
32LQ630H
42LQ640H
42CQ610H
P/NO : MFL62194634 (1309-REV07)
IMPORTANT SAFETY INSTRUCTIONS
3
yyProtect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
yyCAUTION concerning the Power Cord
(Can differ by country):
It is recommended that appliances be placed upon a
dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional
outlets or branch circuits. Check the specification
page of this owner’s manual to be certain. Do
not connect too many appliances to the same AC
power outlet as this could result in fire or electric
shock. Do not overload wall outlets. Overloaded
wall outlets, loose or damaged wall outlets,
yyOnly use attachments/accessories specified by the
manufacturer.
extension cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and
if its appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part
by an authorized service. Protect the power cord
from physical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the appliance. Do
not move the TV with the power cord plugged in.
Do not use a damaged or loose power cord. Be sure
do grasp the plug when unplugging the power cord.
Do not pull on the power cord to unplug the TV.
yyUse only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
yyUnplug this apparatus during lightning storms or
when unused for long periods of time.
yyRefer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
yyWarning - To reduce the risk of fire or electrical
shock, do not expose this product to rain, moisture
or other liquids. Do not touch the TV with wet
hands. Do not install this product near flammable
objects such as gasoline or candles, or expose the
TV to direct air conditioning.
yyDo not expose to dripping or splashing and do not
place objects filled with liquids, such as vases, cups,
etc. on or over the apparatus (e.g. on shelves above
the unit).
yyDo not stick metal objects or any other conductive
material into the power cord. Do not touch the end
of the power cord while it is plugged in.
yyKeep the packing anti-moisture material or vinyl
packing out of the reach of children. Anti-moisture
material is harmful if swallowed. If swallowed
by mistake, force the patient to vomit and visit
the nearest hospital. Additionally, vinyl packing
can cause suffocation. Keep it out of the reach of
children.
IMPORTANT SAFETY INSTRUCTIONS
4
yyGrounding
yyCleaning
(Except for devices which are not grounded.)
Ensure that you connect the earth ground wire to
prevent possible electric shock (i.e. a TV with a
three-prong grounded AC plug must be connected
to a three-prong grounded AC outlet). If grounding
methods are not possible, have a qualified
When cleaning, unplug the power cord and wipe
gently with a soft cloth to prevent scratching. Do
not spray water or other liquids directly on the TV
as electric shock may occur. Do not clean with
chemicals such as alcohol, thinners or benzine.
yyMoving
electrician install a separate circuit breaker. Do not
try to ground the unit by connecting it to telephone
wires, lightening rods, or gas pipes.
Make sure the product is turned off, unplugged
and all cables have been removed. It may take 2 or
more people to carry larger TVs. Do not press or put
stress on the front panel of the TV.
yyVentilation
Power Supply
Short-circuit
Install your TV where there is proper ventilation. Do
not install in a confined space such as a bookcase.
Do not cover the product with cloth or other
materials while plugged. Do not install in excessively
dusty places.
yyIf you smell smoke or other odors coming from
the TV, unplug the power cord and contact an
authorized service center.
yyKeep the product away from direct sunlight.
yyNever touch this apparatus or antenna during a
thunder or lightning storm.
yyWhen mounting a TV on the wall, make sure not
to install the TV by hanging the power and signal
cables on the back of the TV.
yyDo not allow an impact shock or any objects to fall
into the product, and do not drop anything onto the
screen.
yyDisconnecting the Main Power
The power outlet used with this device must remain
easily accessible.
Breaker
yyAs long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if the unit is turned off.
yyDo not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product.
yyOutdoor Antenna Grounding (Can differ by country):
If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power circuits,
or where it can come in contact with such power
lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to
provide some protection against voltage surges
and built-up static charges. Section 810 of the
National Electrical Code (NEC) in the U.S.A. provides
information with respect to proper grounding of the
mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge
unit, connection to grounding electrodes and
requirements for the grounding electrode.
yyStore the accessories (battery, etc.) in a safe
location out of the reach of children.
yyThis apparatus use batteries. In your community
there might be regulations that require you
to dispose of these batteries properly due to
environmental considerations. Please contact your
local authorities for disposal or recycling information.
yyDo not dispose of batteries in a fire.
yyDo not short circuit, disassemble or allow the
batteries to overheat.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Antenna Lead in Wire
Ground Clamp
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
Grounding Conductor
(NEC Section 810-21)
Ground Clamp
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
NEC: National Electrical Code
IMPORTANT SAFETY INSTRUCTIONS
5
yyDot Defect
For USA and Canada
The Plasma or LCD panel is a high technology
product with resolution of two million to six million
pixels. In a very few cases, you could see fine dots
on the screen while you’re viewing the TV. Those
dots are deactivated pixels and do not affect the
performance and reliability of the TV.
FCC NOTICE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
yyGenerated Sound
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated by
plastic thermal contraction due to temperature and
humidity. This noise is common for products where
thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level
noise is generated from a high-speed switching
circuit, which supplies a large amount of current
to operate a product. It varies depending on the
product.
This generated sound does not affect the
performance and reliability of the product.
yyTake care not to touch the ventilation openings.
When watching the TV for a long period, the
ventilation openings may become hot. This does
not affect the performance of the product or cause
defects in the product.
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and the receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
yyIf the TV feels cold to the touch, there may be a
small “flicker” when it is turned on. This is normal,
there is nothing wrong with TV. Some minute dot
defects may be visible on the screen, appearing as
tiny red, green, or blue spots. However, they have
no adverse effect on the TV’s performance. Avoid
touching the LCD screen or holding your finger(s)
against it for long periods of time. Doing so may
produce some temporary distortion effects on the
screen.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference
and (2) this device must accept any interference
received, including interference that may cause
undesired operation of the device.
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
Preventing “Image burn” or “Burn-in” on your TV
screen
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines
for proper grounding and, in particular, specifies
that the cable ground shall be connected to the
grounding system of the building, as close to the
point of the cable entry as practical.
yyIf a fixed image displays on the TV screen for a long
period of time, it will be imprinted and become a
permanent disfigurement on the screen. This is
“image burn” or “burn-in” and not covered by the
warranty.
yyIf the aspect ratio of the TV is set to 4:3 for a
long period of time, image burn may occur on the
letterboxed area of the screen.
yyAvoid displaying a fixed image on the TV screen for
a long period of time (2 or more hours for LCD, 1
or more hours for the Plasma TV) to prevent image
burn.
LICENSES /OPEN SOURCE SOFTWARE NOTICE
6
LICENSES
Supported licenses may differ by model. For more information about licenses, visit ‘www.lg.com’.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for
more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to
play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate
the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on
how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents:
7,295,673; 7,460,668; 7,515,710; 7,519,274”
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product,
please visit ‘http://opensource.lge.com’.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for
download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such
distribution (such as the cost of media, shipping and handling) upon email request to ‘[email protected]’. This offer
is valid for three (3) years from the date on which you purchased the product.
TABLE OF CONTENTS
7
TABLE OF CONTENTS
2
6
6
IMPORTANT SAFETY INSTRUCTIONS
LICENSES
Additional Information
(Depending on model)
The Owner’s Manual and Commercial Mode Setup Guide
contain detailed information on the advanced features of
these TVs. To view the extended documentation, visit
our website at:
OPEN SOURCE SOFTWARE NOTICE
7
TABLE OF CONTENTS
TVs, Systems & Solutions
then the applicable TV. Click the
tab at the bottom of the TV page, and select the required
document(s) from the Downloads list.
LCD TVs
,
page, select
, then
Literature & Downloads
7
Additional Information
8
8
INSTALLATION PROCEdURE
ASSEMBLING ANd PREPARING
8
Unpacking
9
- Protection Cover
10
12
15
16
16
17
18
Front Panel Information
Rear Jack Panel
Lifting and Moving the TV
Setting Up the TV
- Mounting on a Wall
- Kensington Security System (optional)
- Tidying Cables
20 SPECIFICATIONS
21 GENERAL TROUBLESHOOTING
NOTE
yyImage shown may differ from your TV.
yyYour TV’s OSD (On Screen Display) may differ
slightly from that shown in this manual.
yyThe available menus and options may differ from
the input source or product model that you are
using.
yyNew features may be added to this TV in the
future.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
8
INSTALLATION PROCEdURE
Open the package and make sure all the accessories are included.
1
Attach the stand to the TV set.
2
Connect an external device to the TV set.
3
ASSEMBLING ANd PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the dealer where you
purchased your product. The illustrations in this manual may differ from the actual product and item.
(For 22/26/32LQ630H)
Quick Reference Guide
Power Cord
A/V Adapter Cable
(For 22/26LQ630H, 42LQ640H)
(For 32LQ630H)
(For 26LQ630H/42CQ610H)
Cable Holder
1 EA
(See p.18, 19)
Cable Holder
3 EA
(See p.18)
Protective bracket and
screw for power cord
(See p.18, 19)
(For 42LQ640H)
(For 42LQ640H)
(For 42CQ610H)
Power Cord Holder
(See p.19)
Protection cover
(See p.9)
Protection cover
(See p.9)
ASSEMBLING AND PREPARING
9
CAUTION
yyDo not use any unapproved items to ensure the safety and product life span.
yyAny damages or injuries by using unapproved items are not covered by the warranty.
yyIn case of some model, the thin film on screen is a part of TV, So don’t take it off.
NOTE
yyThe items supplied with your product may vary depending on the model.
yyGently wipe any spots on the cabinet with a polishing cloth (included with some models).
yyProduct specifications or contents of this manual may be changed without prior notice due to upgrade of product
functions.
yyWhen using a VGA (D-sub 15-pin signal cable) PC connection, use the shielded signal interface cable with a ferrite
core to maintain standards compliance for the product.
yyFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm (0.39 inches) thick
and 18 mm (0.7 inches) width.
yyUse an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s
USB port.
B
B
A
A
*A 10 mm (0.39 inches)
*B 18 mm (0.7 inches)
Protection Cover
V Image shown may differ from your TV.
For 42CQ610H, 42LQ640H
Install the included protection cover over the hole for the
stand.
Press the Protection cover into the TV until you hear it
click.
ASSEMBLING AND PREPARING
10
Front Panel Information
V Image shown may differ from your TV.
NOTE
yyIf your TV has protection tape attached, remove the tape and then wipe the TV with a cloth, (If a polishing cloth
is included with your TV, please use it).
For 22LQ630H
Remote Control and
Intelligent Sensors
Power Indicator
Off in standby mode.
Illuminates orange when the set is
Speaker
switched on.
Touch Buttons
VOL
ENTER
MENU
INPUT
CH
CHANNEL
VOLUME
(+, -)
ENTER
Button
MENU INPUT POWER
Button Button Button
(
,
)
Buttons
Buttons
For 26/32LQ630H
Remote Control and
Intelligent Sensors
Power Indicator
Off in standby mode.
Speaker
Illuminates orange when the set is
switched on.
Touch Buttons
CHANNEL VOLUME POWER
(
,
)
(+, -)
Button
Buttons
Buttons
ASSEMBLING AND PREPARING
11
For 42CQ610H
CHANNEL(
Buttons
,
)
CH
VOLUME (+, -)
Buttons
VOL
Speaker
ENTER
MENU
INPUT
ENTER Button
MENU Button
INPUT Button
POWER Button
Power/Standby Indicator
Off in standby mode.
Illuminates blue when the set is switched on.
Remote Control Sensor
For 42LQ640H
Speaker
Remote Control and Power Indicator
Button
Description
Scrolls through the saved channels.
Adjusts the volume level.
Turns the power on or off.
ASSEMBLING AND PREPARING
12
Rear Jack Panel
V Image shown may differ from your TV.
For 22LQ630H
10
.1
14
.9 .6
.4
UPDATE RESET
PILLOW SPEAKER
AV IN
VIDEO/AUDIO
.8
13
AUDIO IN SPEAKER CPU SERVICE
(RGB/DVI) OUT(8Ω) (SERVICE ONLY)
ANTENNA
IN
RGB IN (PC)
11
GAME CONTROL
/ M.P.I.
TV-LINK
CFG
PTC SERVICE
(SERVICE ONLY)
/DVI IN
IN
1
2
12
.7
.5
.3
.2
For 26/32LQ630H
.9
10
RESET
UPDATE
14
.1
11
12
12
13
10
Healthcare Multimedia System
GAME CONTROL
/ M.P.I.
ANTENNA IN
SPEAKER OUT
TV-LINK
CFG
PTC SERVICE CPU SERVICE
(SERVICE ONLY)(SERVICE ONLY)
)
(8
PILLOW SPEAKER
.2
.3
.4
.5
.6
.7
.8
ASSEMBLING AND PREPARING
13
For 42CQ610H
2
ANTENNA IN
10
1
6
.3
14
UPDATE
RESET
PTC SERVICE SPEAKER OUT
(SERVICE ONLY)
(8
)
HDMI
2
1
13
12
8
HDMI
/DVI IN
TV-LINK
CFG
.5
PILLOW SPEAKER
AV IN
RS-232C IN
AUDIO IN
(RGB/DVI)
GAME
CONTROL/
M.P.I
RGB IN (PC)
(SERVICE ONLY)
7
11
.9
15
For 42LQ640H
10
12
.1
14
15
PILLOW SPEAKER
8
RESET UPDATE
AUDIO IN
(RGB/DVI)
AV IN
RS-232C
.9
.3
M.P.I
(SERVICE ONLY)
7
PTC SERVICE
(SERVICE ONLY)
RGB IN (PC)
11
SPEAKER OUT
(8
)
ANTENNA/
/DVI IN
OPTICAL DIGITAL CABLE IN
6
1
2
.2
12
13
16
ASSEMBLING AND PREPARING
14
Jack
Description
Power Cord Socket
For operation with AC power.
1
Caution: Never attempt to operate the TV on DC power.
ANTENNA IN/
CABLE IN
Connect over-the air signals to this jack.
2
3
4
PTC SERVICE
(SERVICE ONLY)
Used for PTC software updates.
Used for CPU software updates.
CPU SERVICE
(SERVICE ONLY)
TV - LINK CFG
Computer input for programming Free To Guest services.
For use with external speakers.
5
6
7
SPEAKER OUT (8 )
Ω
GAME CONTROL
M. P. I.
Input port for third party game Controllers.
Allows VOD/PPV devices or set-top boxes to control the TV.
Used to connect to pillow speaker.
PILLOW SPEAKER
AUDIO IN (RGB/DVI)
USB IN
8
9
-
q
w
1/8” headphone jack for analog PC audio input.
Used for viewing multimedia files.
RGB IN (PC)
Analog PC Connection. Uses a D-sub 15-pin cable (VGA cable).
HDMI/DVI IN
Digital Connection.
Supports HD video and Digital audio.
Accepts DVI video using an adapter or HDMI to DVI cable (not included).
AV (Audio/Video) IN
Analog composite connection. Supports standard definition video only (480i).
Used for PC/DTV audio input jack.
e
r
UPDATE
RESET
Software downloads and debug mode enable/ dis-able.
Hardware reset to PTC microcontroller.
Used for software updates.
RS-232C IN
(SERVICE ONLY)
?
@
OPTICAL DIGITAL
Connect digital audio to various types of equipment.
Connect to a Digital Audio Component.
Use an Optical audio cable.
ASSEMBLING AND PREPARING
15
yyWhen transporting a large TV, there should be at
least 2 people.
Lifting and Moving the TV
yyWhen transporting the TV by hand, hold the TV as
shown in the following illustration.
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged and for
safe transportation regardless of its type and size.
CAUTION
yyAvoid touching the screen at all times, as this may
result in damage to the screen.
yyWhen transporting the TV, do not expose the TV to
jolts or excessive vibration.
yyIt is recommended to move the TV in the box or
packing material that the TV originally came in.
yyBefore moving or lifting the TV, disconnect the
power cord and all cables.
yyWhen transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the left
or right.
yyWhen holding the TV, the screen should face away
from you to avoid damage.
yyHold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part, speaker,
or speaker grill area.
ASSEMBLING AND PREPARING
16
Setting Up the TV
Mounting on a Wall
Make sure to use screws and wall mounts that meet the
VESA standard. Standard dimensions for the wall mount
kits are described in the following table.
An optional wall mount can be used with your LG
Television. Consult with your local dealer for a wall
mount that supports the VESA standard used by your TV
model. Install the protection cover provided with the TV
to protect the area where the TV stand would otherwise
be located. Press the protection cover into the TV until
you hear it click. Carefully attach the wall mount bracket
at the rear of the TV. Install the wall mount bracket on a
solid wall perpendicular to the floor. If you are attaching
the TV to other building materials, please contact
qualified personnel to install the wall mount. Detailed
instructions will be included with the wall mount. We
recommend that you use an LG brand wall mount.
Model
22/26LQ630H
100 x 100
M4
32LQ630H
VESA
200 x 100
Standard screw
M4
4
Number of screws 4
Wall mount bracket LSW100B(G)
(optional)
Model
42CQ610H
42LQ640H
VESA
200 x 200
M6
10 cm
Standard screw
Number of screws 4
10 cm
Wall mount bracket LSW200B(G)
(optional)
10 cm
10 cm
LSW220BX
ASSEMBLING AND PREPARING
17
Kensington Security System (optional)
CAUTION
yyDisconnect the power before moving or installing
the TV. Otherwise electric shock may occur.
yyIf you install the TV on a ceiling or slanted wall, it
may fall and result in severe injury.
Use an authorized LG wall mount and contact the
local dealer or qualified personnel.
The Kensington security system connector is located at
the rear of the TV.
For more information of installation and using, refer to
the manual provided with the Kensington security
yyDo not over tighten the screws as this may cause
damage to the TV and void your warranty.
yyUse the screws and wall mounts that meet the
VESA standard. Any damages or injuries by misuse
or using an improper accessory are not covered by
the warranty.
NOTE
yyThe Kensington security system is optional. You
can obtain additional accessories from your local
dealer.
yyEnsure adequate ventilation by following the
clearance recommendations.
yyDo not mount near or above any type of heat
source.
yyDo not put this product next to the patient’s bed
where it can be reached by the patient.
yyInstall product in such a way that patients will not
be able to touch this product.
yyThis product should only be mounted on a wall.
NOTE
yyThe wall mount bracket is optional. You can obtain
additional accessories from your local dealer.
yyUse the screws that are listed in the VESA
standard screw specifications.
yyThe wall mount kit includes an installation manual
and necessary parts.
yyThe length of screws may differ depending on the
wall mount. Make sure to use the proper length.
yyFor more information, refer to the manual supplied
with the wall mount.
ASSEMBLING AND PREPARING
18
Tidying Cables
For 22LQ630H
For 26LQ630H
1
Gather and bind the cables with the cable holder(s)
on the TV back cover.
1
Connect the cables as necessary.
Secure the power cable with the protective bracket
and screw as shown. It will help prevent the power
cable from being removed by accident.
Cable Holder
Protective Bracket
and Screw
For 32LQ630H
2
Gether and bind the cables with the cable holder(s)
on the TV back cover.
1
Gather and bind the cables with the cable holder(s)
on the TV back cover.
Cable Holder
Cable Holder
ASSEMBLING AND PREPARING
19
For 42CQ610H
For 42LQ640H
1
Connect the cables as necessary.
1
Install the power cord holder and power cord. It will
help prevent the power cable from being removed
by accident.
Secure the power cable with the protective bracket
and screw as shown. It will help prevent the power
cable from being removed by accident.
Protective Bracket and Screw
(This feature is not available for all models.)
Power Cord Holder
2
Gather and bind the cables with the cable holder.
2
Install the cable management clip as shown.
Cable Holder
Cable Management Clip
CAUTION
3
Put the cables inside the cable management clip and
snap it closed.
yyDo not move the TV by holding the cable holder
and power cord holder, as the cable holders may
break, and injuries and damage to the TV may
occur.
SPECIFICATIONS
20
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
Power requirement
Television System
AC 120 V ~ 50 / 60 Hz
ATSC / NTSC-M, 64 & 256 QAM
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
75 Ω
Program Coverage
External Antenna Impedance
Environment
condition
Operating Temperature
0 °C ~ 40 °C (32 °F ~ 104 °F)
Less than 80 %
Operating Humidity
Storage Temperature
Storage Humidity
-20 °C ~ 60 °C (-4 °F ~ 140 °F)
Less than 85 %
22LQ630H
(22LQ630H-UA)
MODELS
526.0 x 352.0 x 54.1 (mm)
20.7 x 13.8 x 2.1 (inch)
3.6 kg (7.9 lbs)
Dimensions
(W x H x D)
Weight
Current Value / Power consumption
0.7 A / 45 W
26LQ630H
(26LQ630H-UA)
MODELS
659.0 x 427.8 x 59.0 (mm)
25.9 x 16.8 x 2.3 (inch)
5.9 kg (13.0 lbs)
Dimensions(W x H x D)
Weight
Current Value / Power consumption
0.6 A / 60 W
32LQ630H
(32LQ630H-UA)
MODELS
787.4 x 501.5 x 61.5 (mm)
31.0 x 19.7 x 2.4 (inch)
9.0 kg (19.8 lbs)
Dimensions (W x H x D)
Weight
Current Value / Power consumption
0.7 A / 70 W
42CQ610H
(42CQ610H-UA)
MODELS
1,024 x 621 x 87.1 (mm)
40.3 x 24.4 x 3.4 (inch)
15.1 kg (33.2 lbs)
Dimensions
(W x H x D)
Weight
Current Value / Power consumption
1.5 A / 150 W
42LQ640H
(42LQ640H-UA)
MODELS
991.7 x 604.0 x 55.0 (mm)
39.0 x 23.7 x 2.1 (inch)
13.5 kg (29.7 lbs)
Dimensions (W x H x D)
Weight
Current Value / Power consumption
1.0 A / 100 W
GENERAL TROUBLESHOOTING
21
GENERAL TROUBLESHOOTING
The software may be updated for improvement in performance. The customer is responsible to ensure the compatibility
of their equipment with any LG Electronics software. If needed, please consult with LG Electronics and update new
software versions according to the guidance provided by LG Electronics.”
Installation
Symptom
Possible Cause(s)
Possible Solution(s)
Cannot direct enter
channel number.
yy(TV in Pass-through Mode) Installer
Menu item 028 CH. OVERIDE is set
to 0, i.e., disabled (recommended
setting).
yyIf the channel lineup is locked, only channels
that are active in the TV’s channel lineup can
be selected. Set Installer Menu item 028 CH.
OVERIDE to 1 to allow access for direct keypad
entry to all channels.
yy(TV in FTG Mode) The channel entered yyChannel access is restricted to channels
is not part of the FTG Channel Map.
included in the FTG Channel Map. If necessary,
make changes to the FTG Channel Map using
the FTG File Manager or the FTG Configuration
Application, as appropriate.
No channels present after yyAuto Tuning (Channel Search) not run. yyRefer to Express Script or Custom Master TV
setup.
Setup procedure, as appropriate. Auto Tuning
must be run in order for the channel lineup
to be populated. Note for Express Script: You
must select “Execute Auto Search” in the Auto
Search screen to run the search. To re-activate
the Express Script, set Installer Menu item 117
FACT DEFAULT to 001.
Picture Reception and Sound
Symptom
Possible Cause(s)
Possible Solution(s)
No picture.
yyTV is turned OFF.
yyTurn TV ON.
yyPower failure?
yyAntenna/cable not connected.
yyConnections incorrect.
yyMPI not connected
yyEncrypted program.
yyWrong tuning band.
yyBroadcast problem.
yyAudio muted
yyConnect antenna/cable signal to TV.
yyCheck connections on TV.
yyIf applicable, connect MPI cable to MPI device.
yyTry another channel.
yyAdjust Installer Menu settings.
yyTry a different channel.
Normal picture, poor or
no sound.
yyPress MUTE or use Volume Up key to increase
sound level.
yyPillow/TV speaker not configured
properly.
yyCheck that Installer Menu items 020 FEATURE
LEVEL and 027 HOSPITAL MODE are set as
required. Also, if applicable, select TV Speaker in
the Audio Menu.
Erratic Operation
Symptom
Possible Cause(s)
Possible Solution(s)
Installer Menu setup.
yyWrong Installer Menu settings.
yyAdjust Installer Menu settings as required.
GENERAL TROUBLESHOOTING
22
Installer Remote
Symptom
Possible Cause(s)
Possible Solution(s)
Remote doesn’t work.
yyRemote not in TV Mode.
yyUse MODE key to select “TV”; puts remote into
TV Mode.
yyNot aimed at IR remote sensor.
yyPoint remote at TV’s IR receiver on TV.
yyRemote too far from IR sensor.
yyMove remote closer to TV’s IR receiver or darken
room.
yyMPI not connected.
yyIf applicable, connect MPI cable to MPI device.
yyRemove obstructions.
yyIR path to TV’s receiver obstructed.
yyWeak batteries.
yyReplace batteries.
yyWrong battery polarity.
yyCheck that “+” and “-” match in battery
compartment.
yyToo much light in room.
yyDim room light.
yyWrong Installer Remote.
yyRequires compatible Installer Remote. Contact
your LG dealer.
yyBed Switch set to wrong bed.
yySet Bed Switch or update Installer Menu, as
necessary.
The model and serial numbers of the TV are
located on the back and/or one side of the TV.
Record them below should you ever need service.
LG Customer Information Center
USA, Commercial User
1-888-865-3026
MODEL
CANADA
1-888-542-2623
SERIAL
(For LQ630H, LQ640H series)
This product qualifies for ENERGY STAR in the
“factory default (Home Use)” setting.
Pro:Centric is a trademark of LG Electronics U.S.A., Inc. Pro:Idiom is
a registered trademark of Zenith Electronics LLC. b-LAN is a
trademark of LodgeNet Interactive Corporation. All other trademarks
or registered trademarks are the property of their respective owners.
Changing the factory default settings or enabling other
features may increase power consumption that could
exceed the limits necessary to quality for ENERGY STAR.
|