LEVOIT LUH A602S WUS User Manual

USER MANUAL  
Smart Hybrid Ultrasonic Humidifier  
LV600S Product Series  
Model Line: LUH-A602S  
Model: LUH-A602S-WUS  
Questions or Concerns?  
Please contact us Mon–Fri, 9:00 am–5:00 pm PST/PDT  
at [email protected] or at (888) 726-8520.  
READ AND SAVE  
THESE INSTRUCTIONS  
SAFETY INFORMATION  
To reduce the risk of fire, electric shock, or other injury, follow all instructions and  
safety guidelines.  
Do not use other items as replacement  
General Safety  
parts for this product.  
Only use the humidifier as described in  
this manual.  
Do not cover the nozzles while the  
humidifier is on. Doing so may damage  
the humidifier.  
Place the humidifier and cord so that it  
will not be knocked over. Do not place  
near large pieces of furniture or in high-  
traffic areas.  
Remove the water tank from the base  
before moving the humidifier.  
Do not immerse the humidifier base,  
power cord, or plug in water.  
When not in use, turn the humidifier  
off and disconnect from power by  
removing the plug from the outlet.  
Do not clean the humidifier immediately  
after turning it off, especially if it has  
been diffusing warm mist. Allow the  
humidifier to cool down completely  
before cleaning.  
Do not use the humidifier in wet  
environments.  
Keep the humidifier out of reach from  
children.  
If the humidifier is damaged or is not  
functioning properly, stop using it and  
contact Customer Support immediately  
(see page 27).  
Do not open the base or remove the  
water level sensor for self-servicing.  
Always unplug your humidifier from  
the power outlet before cleaning your  
humidifier or detaching the water tank  
from the humidifier base.  
This humidifier is not to be used by  
persons (including children) with  
reduced physical, sensory, or mental  
capabilities, or lack of experience  
and knowledge, unless they have  
been given supervision or instruction  
concerning use of the appliance by a  
person responsible for their safety.  
Always make sure to place the  
humidifier on a flat, level surface before  
operation.  
Only fill the water tank with clean water.  
Never fill the water tank with any other  
liquids.  
Supervise children when they are near  
the humidifier.  
Do not place the humidifier near  
sources of heat, such as stovetops,  
ovens, or radiators.  
Children should not clean or perform  
maintenance on the humidifier without  
supervision.  
Do not place the humidifier directly on  
floors, carpets, or rugs.  
Not for commercial use. Household use  
only.  
3
SAFETY INFORMATION (CONT.)  
Electromagnetic Fields (EMF)  
Caution: Risk of Leaks and  
Electric Shock  
This humidifier complies with all standards  
regarding electromagnetic fields (EMF).  
If handled properly and according to  
the instructions in this user manual, the  
appliance is safe to use based on scientific  
evidence available today.  
Do not add essential oils,  
supplemental water treatment  
liquids, or water filters into the  
water tank or base chamber. This  
will damage the humidifier and  
cause leaks. Only add essential  
oils to the aroma pad.  
Power & Cord  
Ensure that the plug fits properly into a  
polarized socket.  
Do not handle the power cord or plug  
with wet hands. Keep the plug and power  
cord away from liquids.  
Your humidifier has a polarized plug (one  
prong is wider than the other), which fits  
into a polarized outlet only one way. This  
is a safety feature to reduce the risk of  
electric shock. If the plug does not fit,  
reverse the plug. If it still does not fit,  
do not use the plug in that outlet. Do not  
bypass this safety feature.  
If the power supply cord is damaged, it  
must be replaced by Arovast Corporation  
or similarly qualified persons in order to  
avoid an electric or fire hazard. Please  
contact Customer Support  
(see page 27).  
Unplugging the power cord will disable  
remote control of the humidifier and  
temporarily disconnect the humidifier  
from VeSync and other third-party apps.  
4
GETTING TO KNOW YOUR  
SMART HUMIDIFIER  
Function Diagram  
A. Nozzles  
B. Top Cover  
C. Handle  
Compartment)  
M. Mist Tube  
N. Mist Channel  
O. Noise Silencer  
P. Absorption Pad  
Q. Air Outlet  
R. Float Brackets  
S. Inner Chamber  
T. Power Cord  
U. Water Outlet Valve  
V. Heating Element  
W. Transducer  
Top view of  
inner chamber  
D. Water Tank  
E. Water Filter  
F. Water Filter Sponge  
G. Base  
H. LED Display  
I. Control Panel  
J. Aroma Box  
K. Aroma Pad  
V
W
X
L. Humidity Sensor  
(In Aroma Box  
X. Float  
M
A
B
Back  
Underside  
of water tank  
Front  
N
C
D
O
P
R
E
F
Q
U
T
S
H
K
J
I
L
G
5
GETTING TO KNOW YOUR SMART HUMIDIFIER (CONT.)  
Indicators  
Buttons  
A. Sleep Mode Indicator  
B. Timer Indicator  
C. Wi-Fi® Indicator  
H. On/Off Button  
I. Mist Level Button  
J. Humidity Level Button  
K. Timer Button  
D. No Water Indicator  
E. Relative Humidity (RH) Percentage  
F. Warm Mist Setting Indicator  
G. Mist Level Indicator  
L. Warm Mist Button  
M. Sleep Mode Button  
B
A
C
D
E
H
M
G
F
I
L
J
K
Mist Level Indicator (Blue)  
Warm Mist Indicator (Orange)  
Low Mist  
Heat Off (Cool Mist)  
Low Heat  
Medium Mist  
High Mist  
Medium Heat  
High Heat  
6
CONTROLS  
Note: You can also use the VeSync app to control these functions, as well as additional  
app-only features (see page 15).  
On/Off Button  
Warm Mist Button  
Press to turn the humidifier  
Cycles through warm mist  
settings: low heat, medium  
heat, high heat, and heat  
off (see page 12).  
on/off.  
Press and hold for 5  
seconds to pair with the  
VeSync app. See the  
VeSync in-app instructions  
for more information.  
Sleep Mode Button  
Press to turn Sleep Mode  
on/off (see page 13).  
Press and hold for 15  
seconds to reset the  
humidifier. This will restore  
the humidifier’s default  
settings and disconnect it  
from Wi-Fi® and the VeSync  
app (see page 10).  
Wi-Fi Indicator  
Turns on, off, or blinks to  
indicate pairing status.  
See the VeSync in-app  
instructions for more  
information.  
Mist Level Button  
Press repeatedly to cycle  
through mist level settings:  
low, medium, and high mist.  
No Water Indicator  
Blinks when there is no  
water in the tank. After  
this indicator blinks 10  
times, the humidifier will  
turn off. Refill the tank  
and properly place it  
on the base to use your  
humidifier.  
Press and hold for 3  
seconds to turn the display  
off. Press any button to turn  
the display back on.  
Humidity Level Button  
Sets the relative humidity  
(RH) percentage. The  
Lights up when the  
water tank is removed.  
Remains on until the tank  
is replaced.  
humidifier will automatically  
stop misting when the room  
reaches the target humidity  
level (see page 12).  
Press and hold for 2  
seconds to cancel your  
humidity level setting.  
Timer Button  
Sets or cancels a timer  
(see page 13).  
7
GETTING STARTED  
1. Remove all packaging.  
2. Clean the water tank and water tank  
cover before first use.  
12 in /  
30 cm  
Note: Check to make sure that the  
water filter is correctly in place. If not,  
then rotate the filter clockwise to secure  
it in place.  
12 in /  
30 cm  
3. Choose a hard, flat location for the  
humidifier at least 12 inches / 30 cm away  
from any walls. The surface must be  
water-resistant. [Figure 1.1]  
Figure 1.1  
Do not place the humidifier directly  
on floors, carpets, or rugs.  
4. Mist should be directed away from walls,  
furniture, bedding, and appliances. Avoid  
letting too much mist fall on the side of  
the humidifier with the aroma box, as this  
may interfere with the sensor inside the  
aroma box.  
Note: The humidity sensor and an air  
inlet are both located inside the aroma  
box. Placing the humidifier away from  
walls will also ensure that the inlet and  
sensor function properly.  
8
FILLING & REFILLING  
3. Replace the water tank cover and place  
Note: Make sure the water tank is clean  
the tank back on the base. [Figure 2.1]  
before filling.  
1. Remove the water tank cover.  
2. Use the handle to remove the tank  
from the base. Fill the tank with room-  
temperature water. Do not fill with hot  
water.  
Note:  
We recommend using purified  
water to fill the tank.  
Using tap water may result in a  
white dust (dried minerals) on  
surfaces.  
Figure 2.1  
Caution  
Do not add water directly into the  
base chamber. [Figure 2.2]  
Do not add essential oils into the  
humidifier. Only add essential oils  
to the aroma pad. [Figure 2.4]  
Figure 2.2  
Figure 2.4  
Do not add water through the  
mist tube. [Figure 2.3]  
Do not use water treatment liquids  
or third-party water filters in this  
humidifier. [Figure 2.5]  
Figure 2.3  
Figure 2.5  
9
VESYNC APP SETUP  
Note: Due to ongoing updates and  
improvements, the VeSync app may be  
slightly different than shown in the manual.  
In case of any differences, follow the in-app  
instructions.  
3. Follow the in-app instructions to set up  
your smart humidifier.  
Note:  
You can use the VeSync app to  
connect your smart humidifier  
to Amazon Alexa or Google  
Assistant™. Follow the in-app  
instructions to connect VeSync to  
your voice assistant.  
1. To download the VeSync app, scan  
the QR code or search “VeSync” in the  
Apple App Store® or Google Play Store.  
Note: For Android™ users, choose  
Your phone must have  
Allow” to use VeSync.  
Location turned on while  
your phone is connecting to  
your smart humidifier. This  
is required to establish the  
Bluetooth® connection. You can  
turn Location off after your smart  
humidifier is finished connecting to  
the VeSync app.  
2. Open the VeSync app. If you already  
have an account, tap Log In. To create a  
new account, tap Sign Up.  
Note: You must create your own  
VeSync account to use third-party  
services and products. These will not  
work with a guest account. With a  
VeSync account, you can also allow  
your family and friends to control your  
smart humidifier.  
Wi-Fi Connection  
1. To disconnect Wi-Fi, press and hold  
for 15 seconds until the Wi-Fi  
indicator turns off. This will restore the  
smart humidifier’s default settings and  
disconnect it from the VeSync app.  
2. To reconnect, please follow the  
instructions in the VeSync app for  
adding a device.  
10  
USING YOUR SMART HUMIDIFIER  
Note: Using the VeSync app allows you to  
control your smart humidifier remotely and  
access additional functions and features  
(see page 15).  
1. Plug in the humidifier. The humidifier will  
light up, then turn off.  
2. Press  
to turn your humidifier on. The  
humidifier will start misting.  
Note: If there is no water in the tank,  
will flash 10 times, and the humidifier will  
turn off. Fill the water tank (see Getting  
Started, page 8).  
3. Press  
repeatedly to cycle through  
mist settings: Low, Medium, and High.  
4. Rotate the nozzles to adjust the direction  
Figure 3.1  
of the mist. [Figure 3.1]  
Note:  
Direct the nozzles away from any  
furniture, walls, or other objects to  
prevent them from getting wet.  
Do not inhale the mist directly from  
the nozzles.  
5. Optionally, use the controls or the  
VeSync app to turn on warm mist,  
activate Sleep Mode, and more (see  
Controls, page 7).  
6. When your room has reached your  
preferred humidity level, turn the  
humidifier to a lower setting, or turn it off.  
A comfortable humidity level is between  
40% and 60%.  
Note: You can also set the humidifier  
to automatically stop misting when the  
room reaches a specific humidity level  
(see Humidity Level, page 12).  
7. Press  
to turn your humidifier off.  
11  
USING YOUR SMART HUMIDIFIER (CONT.)  
Note:  
Warm Mist  
The humidifier will automatically  
mist for 15 seconds after being  
turned on, even if the room has  
reached the set humidity level.  
Press  
to turn on warm mist. Keep  
pressing to increase the heat setting for  
the mist, and to turn warm mist off.  
Press  
once to see the selected  
Caution: Mist may be hot. Do not place  
your bare hands, face, or other exposed  
skin over the nozzles while using warm  
mist. [Figure 3.2]  
humidity level again. Keep pressing  
to change the humidity level.  
You can still adjust the mist level,  
the timer, and the warm mist setting  
after setting the humidity level.  
The humidifier may take 15 minutes to  
warm up before producing warm mist.  
The humidifier will not increase the  
mist level when a humidity level  
percentage is set, only stop misting  
once the set humidity level is  
The warm mist function can be used  
during Sleep Mode.  
reached. If you want the humidity in  
your room to increase faster, set the  
humidifier to high mist level.  
3. Once the humidity of the environment  
reaches the humidity you set, the  
humidifier will automatically stop misting.  
4. The humidifier will continue detecting  
the humidity level in the room. It will  
start misting again when the humidity  
drops to 5% below the set level.  
Note:  
To cancel the set humidity level,  
press and hold for 2 seconds,  
Figure 3.2  
which will set the humidity level to  
“--”. The display will flash 3 times  
to confirm, then return to showing  
the current humidity percentage in  
the room.  
Humidity Level  
You can customize the humidity level that  
the humidifier will maintain. The humidifier  
will automatically stop misting when the  
room reaches the target humidity level.  
When the humidity level is set to  
“--” the humidifier will automatically  
keep misting at the current mist  
level until it runs out of water.  
1. Press  
repeatedly to set a humidity  
level between 40% and 80% Relative  
Humidity (RH).  
2. The display will flash 3 times to confirm  
your selection, then return to showing  
the current humidity percentage in the  
room.  
12  
USING YOUR SMART HUMIDIFIER (CONT.)  
When Sleep Mode is on, you can press  
any button to wake up the display. If you  
stop touching the display, the display  
will turn off again after 6 seconds.  
Timer  
You can set an auto-shutoff timer between  
1 and 12 hours.  
When Sleep Mode is on, you can use all  
other settings except changing the mist  
level or humidity level. If you change the  
mist level or humidity level, Sleep Mode  
will turn off.  
Press  
repeatedly to choose a time  
in increments of 1 hour. When you stop  
pressing  
times and the timer will start.  
, the display will flash 3  
When Sleep Mode is turned on, the  
humidifier will automatically mist for 15  
seconds, even if the room’s humidity  
level is over 60%.  
The humidifier will automatically power  
off once the timer is finished.  
To cancel a timer, press and hold  
for 3 seconds. You can also press  
repeatedly until the display reads “--” or  
use the VeSync app.  
Turning Off the Display  
The display will automatically dim after 30  
seconds of inactivity.  
Sleep Mode  
To turn off the display, press and hold  
for 3 seconds.  
Sleep Mode changes the humidifier’s mist  
setting to an automatic mode and turns off  
the display lights.  
To turn the display back on, press any  
button.  
Press  
to turn Sleep Mode on/off.  
Sleep Mode automatically turns off  
warm mist to reduce noise. You can  
press  
to turn warm mist back on.  
Sleep Mode uses the humidity sensor to  
detect the relative humidity in the room  
and automatically adjusts the mist level  
to maintain 50–60% relative humidity.  
Room Relative Automatic Mist Level  
Humidity  
Under 50%  
50–55%  
High  
Medium  
Low  
55–60%  
Over 60%  
Automatic Shutoff  
13  
USING YOUR SMART HUMIDIFIER (CONT.)  
Using the Aroma Box  
Your humidifier can be used for  
aromatherapy.  
1. Push the aroma box at the back of the  
base and pull it out. [Figures 3.3]  
2. Put 8–10 drops of essential oils on the  
aroma pad. [Figure 3.4]  
3. Place the aroma box back into the  
humidifier.  
4. Turn on the humidifier. The humidifier  
will automatically diffuse aroma when  
used.  
Figure 3.3  
Note:  
Do not add essential oils, water  
treatment liquids, or third-party water  
filters into the water tank or base  
chamber. Only add essential oils to the  
aroma pad. [Figure 3.5]  
The aroma pads can be cleaned and  
reused after diffusing essential oils (see  
Cleaning the Aroma Pad, page 19).  
This humidifier uses a small heat-based  
aroma diffuser. The aroma is intended  
to be light.  
Figure 3.4  
Figure 3.5  
14  
USING YOUR SMART HUMIDIFIER (CONT.)  
Absorption Pads  
VeSync App Functions  
The mineral absorption pads help reduce  
mineral buildup (scale) inside the humidifier,  
especially on the heating element.  
The VeSync app allows you to access  
additional smart functions, including those  
listed below.  
Note: For information on replacement  
aroma pads or absorption pads, see  
page 19.  
Remote Control From Your Phone  
Turn the humidifier on/off.  
Cycle through mist levels and heat  
levels, and turn Sleep Mode on/off.  
Turn the display lights light on/off.  
Monitor Humidity Levels  
Check current humidity levels in the  
humidifier’s environment.  
Set Timers & Schedules  
Program individual timers or create a  
schedule for your smart humidifier.  
Memory Function  
Third-Party Voice Control  
The humidifier will remember your  
settings for Mist Level, Humidity Level,  
Warm Mist, and Wi-Fi settings when  
turned off or unplugged, and will  
resume those settings when turned  
back on.  
The humidifier will not remember Sleep  
or Timer settings, and the display will  
automatically turn back on when the  
humidifier is turned back on.  
Compatible with Amazon Alexa and  
Google Assistant™ for voice commands.  
Note: The VeSync app is continually updated and  
app features will expand.  
Automatic Shutoff  
The humidifier will automatically turn off  
when all of the water in the tank has been  
diffused.  
will show on the display and  
blink 10 times before the humidifier turns  
off. Fill the water tank (see Getting Started,  
page 8).  
If the tank has been removed from the base,  
the humidifier will automatically stop misting.  
will show on the display, and will turn off  
once the tank is placed properly back on  
the base.  
15  
IMPORTANT TIPS  
Your humidifier must have the correct level  
of water in the base chamber to work  
properly. If there is too much water in the  
base chamber, the humidifier cannot create  
mist.  
Do not place the humidifier on an  
inclined surface.  
Never pour water directly into the  
base chamber. [Figure 4.1] Only add  
water to the water tank. The humidifier  
will automatically release the correct  
amount of water into the base chamber.  
Avoid moving or shaking the humidifier.  
This may cause the water tank to  
release too much water into the base  
chamber.  
Before moving the humidifier, turn it off,  
unplug it, and remove the water tank.  
Empty any excess water from the base  
chamber.  
Figure 4.1  
CARE & MAINTENANCE  
Note:  
Note:  
All maintenance should be done on  
a water-resistant surface, such as a  
kitchen counter.  
Never immerse the base in water or  
liquid. Do not place any part of the  
humidifier in a dishwasher.  
Change the water daily to avoid  
bacteria growth.  
Do not use detergents to clean the  
humidifier.  
Use a tissue or cloth to clean the  
nozzles regularly.  
1. Unplug the humidifier.  
If not using the humidifier for 1 week or  
longer, do not leave water inside. Clean  
and dry the humidifier instead.  
Note: If you’ve been using the warm  
mist setting, allow the humidifier to cool  
before cleaning.  
Cleaning  
You should clean your humidifier every  
week, and when you’re ready to store it.  
16  
2. Remove and rinse the water tank cover.  
3. Remove the water tank from the base,  
and remove the mist channel and mist  
tube. [Figure 5.1] Pour out any water from  
the tank and base chamber. If you’ve  
used the warm mist setting, use caution  
in case the water is still hot.  
6. Detach the mist tube from the  
mist channel by twisting the tube  
counterclockwise. [Figure 5.1]  
7. Remove the float, noise silencer,  
absorption pad, and aroma box from the  
base. [Figure 5.4]  
Note: When pouring out water, hold  
down the float to ensure that it does  
not fall out of the base chamber.  
4. Remove the water filter from the tank by  
rotating it counterclockwise and lifting it  
out. [Figure 5.2]  
5. Remove the water filter sponge from  
the water filter if necessary for cleaning.  
[Figure 5.3]  
Figure 5.1  
Figure 5.3  
Float  
Noise Silencer  
Figure 5.2  
Absorption pad  
Aroma box  
Figure 5.4  
17  
CARE & MAINTENANCE (CONT.)  
11. Dry all parts with a cloth. Make sure  
all parts are completely dry before  
reassembling or storing.  
8. Detach the outer water outlet valve from  
the tank by rotating it counterclockwise.  
[Figure 5.4]  
9. Rinse all parts (except the outside of the  
base) with room temperature water.  
10. To descale the humidifier (remove  
mineral buildup):  
a. Remove the water filter and the  
water outlet valve from the tank.  
Remove the noise silencer and  
absorption pad from the base. Keep  
the mist tube and mist channel in  
place.  
Figure 5.4  
b. Fill the tank with 3 US cups / 710 mL  
of distilled white vinegar.  
c. Replace the tank cover and swish  
the vinegar around the tank.  
d. Place the tank on the base and soak  
for 15–20 minutes. Vinegar will drain  
into the base chamber and loosen  
scale (mineral buildup) in the tank  
and in the base chamber (including  
the transducer and float).  
e. Remove the tank, remove the tank  
Figure 5.5  
cover, and pour out any vinegar.  
f. Remove the float from the base  
chamber by pulling up the larger  
side of the float and pulling the shaft  
out from the float brackets. One  
side of the float brackets is open  
(U-shaped) to allow the shaft to be  
removed. [Figure 5.5]  
Do not allow liquid  
into the air outlet  
g. Place the float, water filter, water  
outlet valve, aroma box, and noise  
silencer in a container. Fill with  
enough vinegar to cover them. Soak  
for 15–20 minutes.  
h. Use a soft cloth and the included  
cleaning brush to remove scale from  
all parts. [Figure 5.6]  
i. Rinse all parts until any vinegar smell  
is completely gone.  
Figure 5.6  
18  
CARE & MAINTENANCE (CONT.)  
Cleaning the Aroma Pad &  
Absorption Pad  
Replacing the Aroma Pad &  
Absorption Pad  
1. Pull out the aroma box and remove the  
If the aroma pad or absorption pad is stiff  
even after cleaning, then it needs to be  
replaced. Extra pads are included with the  
humidifier.  
aroma pad. [Figure 5.7]  
2. Remove the noise silencer, then remove  
the absorption pad from on top of the  
heating element. [Figure 5.8]  
To maintain the performance of your  
humidifier, only use official Levoit aroma  
pads and absorption pads. For more  
information, contact Customer Support  
(see page 27).  
3. Rinse the pads under warm, running  
water.  
4. Dry the pads with a clean cloth.  
5. Place the aroma pad back into the  
aroma box.  
6. Place the absorption pad back into the  
base.  
Note: Do not use liquid cleaners or  
detergents to clean the pads or any  
other part of the humidifier.  
Figure 5.7  
Figure 5.8  
19  
CARE & MAINTENANCE (CONT.)  
Reassembling  
1. Place the float back into the base  
chamber: [Figure 5.9]  
a. Make sure the correct side of the  
Figure 5.9  
float is facing up.  
b. Insert the smaller prong into the  
closed side of the float brackets.  
c. Place the larger prong into the  
open (U-shaped) side of the float  
brackets.  
2. Place the absorption pad and the noise  
silencer back over the heating element.  
[Figure 5.10]  
3. Screw the mist tube back onto the mist  
channel by twisting the tube clockwise.  
Place securely into place back over the  
base chamber. [Figure 5.10]  
4. Place the outer water outlet valve back  
onto the tank by rotating it. [Figure 5.11]  
5. Make sure the water filter sponge is  
securely placed inside the water filter.  
Place the water filter back into the tank  
and rotate it clockwise to secure it in  
place. [Figure 5.12]  
Figure 5.10  
6. Refill the tank, if necessary. Place the  
tank properly on the base and place the  
tank cover on the water tank.  
Storing  
Follow the cleaning instructions (see page  
16) and allow all parts to dry completely  
before storing. Store in a cool, dry location.  
Figure 5.11  
Figure 5.12  
20  
TROUBLESHOOTING  
Problem  
Possible Solution  
Humidifier doesn’t  
turn on, or turns off  
unexpectedly.  
Plug the humidifier into a working outlet and turn it on.  
Add purified water to the water tank.  
Turn the mist level to a higher setting.  
Fill the water tank.  
Little or no mist comes  
out.  
There may be too much water in the base chamber. Empty the base  
chamber. Refill the water tank (not the base chamber) and place the water  
tank properly onto the base.  
Make sure the air inlets on the bottom of the base and in the aroma box  
are not blocked. The humidifier should not be set on carpet or other  
surfaces that may block the air inlets.  
Clean the humidifier (see Care & Maintenance, page 16). Make sure  
the nozzles are not blocked or clogged.  
Make sure the humidifier is on a level surface.  
If the water tank or base was washed with detergent, rinse thoroughly with  
clean water to remove any detergent.  
Clean the water filter (see page 16) or replace the water filter sponge  
with a new one. One replacement water filter sponge is included with this  
humidifier. For information on additional replacements, contact Customer  
Support (see page 27).  
Humidifier uses water too  
quickly.  
The humidifier uses up water based on the environmental temperature  
and humidity. If your environment is cold and/or dry, the humidifier will run  
out of water faster.  
Using the warm mist function will use up water faster.  
Humidifier produces an  
unusual smell.  
If the humidifier is new, unplug and rinse all parts, then place in a cool, dry  
place for 12 hours.  
If essential oils were placed on the aroma pad, rinse the pad under clean  
water and allow it to dry.  
Clean the humidifier (see Care & Maintenance, page 16).  
21  
TROUBLESHOOTING (CONT.)  
Problem  
Possible Solution  
Humidifier makes a loud  
or unusual noise.  
Make sure the water tank is properly in place (see Getting Started, page  
8).  
Set mist level to a lower setting.  
Empty the base chamber. Refill the water tank (not the base chamber) and  
place the water tank properly onto the base.  
When using the warm mist function, the heating element may make a  
gurgling noise if the water level is low. Add more water to the water tank.  
The humidifier may be malfunctioning. Stop using the humidifier and  
contact Customer Support (see page 27).  
Mist leaks from the base.  
Make sure the water tank is properly in place (see Getting Started, page  
8).  
White dust appears  
around or in the  
humidifier.  
We recommend using purified to fill the humidifier. Avoid using water with  
high mineral content, such as tap water.  
Clean the humidifier (see Care & Maintenance, page 16).  
Avoid running the humidifier in a room with over 60% relative humidity.  
Wipe any excess water off the top and bottom of the base.  
Do not shake the humidifier.  
Water visibly leaks from  
the humidifier.  
Make sure to place the humidifier on a flat, level surface.  
Check the water tank for leaks. If there are leaks, contact Customer  
Support (see page 27).  
The area around the  
humidifier is damp or wet  
from condensation.  
Humidity may be too high. Turn down the mist level, turn off the humidifier,  
or open a door or window to the room.  
Open a window to ensure proper airflow for the humidifier, or move the  
humidifier to a more well-ventilated room.  
Make sure the water tank is properly in place (see Getting Started, page  
8).  
When replacing the water tank, wipe off excess water from the water tank  
and base.  
22  
TROUBLESHOOTING (CONT.)  
Problem  
Possible Solution  
Mist is not warm after  
Allow the humidifier to heat up for about 15 minutes to produce warm mist.  
pressing  
.
Clean the heating element (see Care & Maintenance,  
page 16).  
The mist is warm on the  
cool mist setting.  
The heating element may still be warm after being used for warm mist.  
Allow the heating element to cool for at least 30 minutes.  
Mold grows inside the  
humidifier.  
Clean the water tank and base chamber regularly (see Care &  
Maintenance, page 16).  
Fill the water tank.  
lights up red.  
Place the water tank properly on the base.  
Clean the water filter (see page 16) or replace it with a new one. To  
request a new water filter, contact Customer Support (see page 27).  
Essential oil has little or  
no smell.  
Add more essential oil. For best results, use pure essential oil.  
Display shows an  
incorrect humidity  
percentage.  
The room may be larger than the humidifier’s effective range. Move to a  
room smaller than 430–753 ft² / 40–70 m².  
Moisture may have built up inside the humidity sensor. Make sure the  
nozzles are facing away from the aroma box so that mist does not settle  
on the sensor inside the aroma box (see diagram in Getting To Know Your  
Smart Humidifier, page 5). Turn off the humidifier, remove the aroma  
box, and allow the sensor to air dry.  
If the humidifier is placed within 12 inches / 30 cm of a wall or in a corner,  
the humidity sensor cannot provide a proper reading for the relative  
humidity in the room.  
The humidity sensor will give an improper reading if it is exposed to dust.  
Avoid using the humidifier in dusty rooms. Avoid using tap water in the  
humidifier, as this can increase dust in the air.  
The humidity level isn’t  
changing in my room.  
Use a higher mist level setting.  
Depending on your environment, the humidifier may take longer to  
humidify your air.  
The room may be larger than the humidifier’s effective range. If the room is  
larger than 430–753 ft² / 40–70 m², the humidifier will not be as effective.  
Display shows Error Code  
“E1”, “E2”, “E3”, “E4”, or  
“E6”.  
The humidifier is malfunctioning. Contact Customer Support (see page  
page 27).  
23  
VESYNC APP TROUBLESHOOTING  
Why isn’t my humidifier connecting to the VeSync app?  
Make sure your phone has Bluetooth® turned on and is not currently connected to another  
Bluetooth device.  
During the setup process, you must be on a secure 2.4GHz Wi-Fi network. Confirm that the  
network is working correctly.  
Make sure the Wi-Fi password you entered is correct.  
Make sure your humidifier and phone are within 30 ft / 10 m of each other.  
Reset the humidifier by pressing and holding  
for 15 seconds. Then try connecting again.  
My humidifier is offline.  
Make sure the humidifier is plugged in. The humidifier may appear to be offline if it is  
unplugged, or if the outlet does not have power.  
Refresh the VeSync menu by swiping down on the screen.  
Make sure your router is connected to the internet and your phone’s network connection is  
working.  
Reset the humidifier using one of these options:  
a.  
Delete the humidifier from the VeSync app. Swipe left (iOS®) or press and hold  
(Android), then tap Delete. Then reconfigure your humidifier with the VeSync app.  
b. Press and hold  
app.  
for 15 seconds. Then reconfigure your humidifier with the VeSync  
Note: Power outages, internet outages, or changing Wi-Fi routers may cause your humidifier  
to go offline.  
The VeSync app is displaying an incorrect humidity percentage while the humidifier is  
turned on.  
The room may be larger than the humidifier’s effective range. Move to a room smaller than  
430–753 ft² / 40–70 m².  
Moisture may have built up inside the humidity sensor. Make sure the nozzles are facing  
away from the aroma box so that mist does not settle on the sensor inside the aroma  
box (see diagram in Getting To Know Your Smart Humidifier, page 5). Turn off the  
humidifier, remove the aroma box, and allow the sensor to air dry.  
If the humidifier is placed within 12 inches / 30 cm of a wall or in a corner, the humidity  
sensor cannot provide a proper reading for the relative humidity in the room.  
The humidity sensor will give an improper reading if it is exposed to dust. Avoid using the  
humidifier in dusty rooms.  
If your problem is not listed, please contact Customer Support (see page 27).  
24  
FEDERAL COMMUNICATION COMMISSION INTERFERENCE  
STATEMENT - PART 15  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
1. This device may not cause harmful interference, and  
2. This device must accept any interference received, including interference that may cause undesired operation.  
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in  
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could  
void the user’s authority to operate this equipment.  
FCC RADIATION EXPOSURE STATEMENT  
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users  
must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with  
FCC RF exposure compliance requirements, please follow operation instructions as documented in this manual. This  
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment  
should be installed and operated with a minimum distance of 20 cm between the radiator and your body. The  
availability of some specific channels and/or operational frequency bands are country dependent and are firmware  
programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.  
FEDERAL COMMUNICATION COMMISSION INTERFERENCE  
STATEMENT - PART 18  
This device complies with part 18 of the FCC Rules.  
This equipment generates and uses ISM frequency energy and if not installed and used properly, that is in strict  
accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has  
been type tested and found to comply with limits for an ISM Equipment pursuant to part 18 of FCC Rules, which are  
designed to provide reasonable protection against such interference in a residential installation. However, there is  
no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to  
radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the following:  
Reorient the receiving antenna of radio or television.  
Relocate the equipment with respect to the receiver.  
Move the equipment away from the receiver.  
Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.  
Conduct only the user maintenance found in this manual. Other maintenance and servicing can cause harmful  
interference and can void the required FCC compliance. The manufacturer is not responsible for any radio or TV  
interference cause by unauthorized modification to the equipment. It is the responsibility of the user to correct such  
interference.  
25  
WARRANTY INFORMATION  
Arovast will not be liable for indirect, incidental, or  
consequential damages in connection with the use  
of the product covered by this warranty.  
Product Smart Hybrid Ultrasonic  
Humidifier  
Model LUH-A602S-WUS  
This warranty extends only to the original  
consumer purchaser of the product and is not  
transferable to any subsequent owner of the  
product regardless of whether the product is  
transferred during the specified term of the  
warranty.  
For your own reference, we strongly recommend  
that you record your order ID and date of  
purchase.  
Order ID  
Date of Purchase  
This warranty does not extend to products  
purchased from unauthorized sellers. Arovast’s  
warranty extends only to products purchased from  
authorized sellers that are subject to Arovast’s  
quality controls and have agreed to follow its  
quality controls.  
Terms & Policy  
Arovast Corporation (Arovast”) warrants this  
product to the original purchaser to be free from  
defects in material and workmanship, under  
normal use and conditions, for a period of 2 years  
from the date of original purchase.  
All implied warranties are limited to the period of  
this limited warranty.  
This warranty gives you specific legal rights  
and you may also have other rights which  
vary from state to state. Some states do not  
allow the exclusion or limitation of incidental or  
consequential damages, so the above limitation or  
exclusion may not apply to you.  
Arovast agrees, at our option during the  
warranty period, to repair any defect in material  
or workmanship or furnish an equal product in  
exchange without charge, subject to verification  
of the defect or malfunction and proof of the date  
of purchase.  
If you discover that your product is defective within  
the specified warranty period, please contact  
Customer Support via [email protected].  
DO NOT dispose of your product before  
contacting us. Once our Customer Support Team  
has approved your request, please return the  
product with a copy of the invoice and order ID.  
There is no other express warranty. This warranty  
does not apply:  
If the product has been modified from its  
original condition;  
If the product has not been used in  
accordance with directions and instructions  
in the user manual;  
Every Levoit product automatically includes a  
2-year warranty. To make the customer support  
process quick and easy, register your product  
To damages or defects caused by accident,  
abuse, misuse or improper or inadequate  
maintenance;  
To damages or defects caused by service  
or repair of the product performed by an  
unauthorized service provider or by anyone  
other than Arovast;  
This warranty is made by:  
Arovast Corporation  
1202 N. Miller St. Suite A  
Anaheim, CA 92806  
To damages or defects occurring during  
commercial use, rental use, or any use for  
which the product is not intended;  
To damages or defects exceeding the cost  
of the product.  
26  
CUSTOMER SUPPORT  
If you have any questions or concerns about  
your new product, please contact our helpful  
Customer Support Team.  
Arovast Corporation  
1202 N. Miller St., Suite A  
Anaheim, CA 92806  
Toll-Free: (888) 726-8520  
Support Hours  
Mon–Fri, 9:00 am–5:00 pm PST/PDT  
*Please have your order invoice and order ID  
ready before contacting Customer Support.  
ATTRIBUTIONS  
Apple App Store is a trademark of Apple Inc.  
Google, Android, and Google Play are trademarks of Google LLC.  
Wi-Fi® is a registered trademark of Wi-Fi Alliance®.  
Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates.  
iOS is a registered trademark of Cisco Systems, Inc. and/or its affiliates in the United States and certain other  
countries.  
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use  
of such marks by Arovast Corporation is under license. Other trademarks and trade names are those of their  
respective owners.  
27  
/LEVOIT  
/LEVOIT  
/LEVOITLIFESTYLE  
/LEVOITLIFESTYLE  
/LEVOITLIFESTYLE  
LEVOIT.COM  
JJ081721AL-M1_0621LUH-A602-WUS  

White Rodgers Acb1000 User Manual
Whirlpool Acu082 User Manual
Sanyo Twicell Hr 3uhs User Manual
Sanyo Cl0971 User Manual
LG BEKO LG BKE 7630 NS G User Manual
JVC DLA VS2300ZG User Manual
D LINK DCH M225 User Manual
DELL ULTRASHARP UP2718Q User Manual
BLACK DECKER LDX112 User Manual
BLACK DECKER BDH1200PVAV User Manual