CD-RECEIVER
KDC-X994
KDC-BT945U
KDC-X794
KDC-MP745U
INSTRUCTION MANUAL
The latest version of the Instruction Manual can be downloaded from www.
kenwood.com/cs/ce/. Before reading this manual, please access this site to
check whether your manual is the latest one.
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the
warranty card, and in the space provided below. Refer to the model and serial numbers
whenever you call upon your Kenwood dealer for information or service on the product.
Model KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Serial number
US Residents Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
© IM305_Ref_en_02_K
DSP Setup
Car Type Selection
Speaker Setting
42
Basic Operations of remote control
Appendix
60
62
About Audio file
iPod/iPhone that can be connected to this unit
About USB device
About “KENWOOD Music Editor”
About the Cell-Phone
About the Bluetooth Audio player
About Satellite Radio tuner (Optional)
About HD Radio Reception (Optional)
Menu List
Car Type Fine Adjustments
X’Over Setting
Audio Preset Memory
Audio Preset Recall
Favorite Control
Favorite Preset Memory
Favorite Preset Recall
46
48
Favorite Preset Memory Delete
Display Indicator items
Bluetooth Setup
Accessories/ Installation Procedure
Connecting Wires to Terminals
Installation/Removing the Unit
Troubleshooting Guide
69
70
71
73
76
Bluetooth Setting
Registering Bluetooth device
Registering PIN Code
Selecting the Bluetooth device You Wish to
Connect
Deleting a Registered Bluetooth device
Downloading the Phone Book
Adding a Voice Dialing Command
Setting a Voice Command for Category
Specifications
SMS (Short Message Service)
54
Downloading the SMS
SMS (Short Message Service)
Satellite Radio Tuner Control (Optional) 56
Basic Operation
Satellite Radio Setting
Category and Channel Search
Preset Memory
Preset Tuning
Channel Scan
Direct Access Tuning
HD Radio™ Tuner Control (Optional)
58
Basic Operation
Station Preset Memory
Auto Memory Entry
Preset Tuning
HD Radio™ Setting
Direct Access Tuning
iTunes Tagging
English
|
3
Before use
Lens Fogging
2WARNING
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
To prevent injury or fire, take the following
precautions:
To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Do not use this unit before canceling
Demonstration mode!
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
Demonstration mode. Refer to <Before Using> (page
7).
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• Characters that conform to ISO 8859-1 can be
displayed.
How to reset your unit
If this unit or the connected unit (auto disc changer,
etc.) fails to operate properly, press the Reset button.
The unit returns to factory settings when the Reset
button is pressed.
• The RDS feature won’t work where the service is not
supported by any broadcasting station.
Reset button
• In this document, the description indicator will
light means a status is displayed. Refer to <Basic
Operation> (page 28) for the details of the status
display.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
¤
• Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
Unit and Faceplate Terminals
• To prevent deterioration, do not touch the terminals
of the unit and faceplate with your fingers.
• If the terminals on the unit or faceplate get dirty,
wipe them with a clean soft dry cloth.
|
4
KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
CDs that cannot be used
• CDs that are not round cannot be used.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not
been finalized. (For the finalization process refer to
your CD-R/CD-RW writing software, and your CD-R/
CD-RW recorder instruction manual.)
• 3 inch CD cannot be used. Attempt to insert using
an adapter can cause malfunction.
English
|
5
Component names and functions
5
4
3
6
2
1
AUX
14
10
13
9
12
8
11
7
1
8
[SRC] button
Release button
To drop the faceplate down to open and CD can be
To turn on this unit and select the Source (press the
inserted or ejected (press the button).
button).
To turn off this unit (press the button at least 1
second).
2
[MENU] button
To select a song or set functions. See <Menu List
9
[
4
] / [¢] buttons
To select station, song and setting items. (press the
button).
3
[DISP] button
To change display item (press the button).
[VOL] knob
10 [38] button
To start or interrupt playback for CD, audio file, and
iPod (press the button).
To select the remove mode, and remove the USB
device or an iPod (press the button at least 2 seconds).
4
To adjust volume (turn the knob).
To select menu list item (turn and press the knob). See
<Menu List Operation> (page 7) for details.
KDC-X994/KDC-BT945U : Enters Play mode Menu
(press the button at least 1 second).
11 [ ] button (KDC-X994/ KDC-BT945U)
KDC-X794/KDC-MP745U : To make a voice dialing call
(press the button at least 1 second).
To enter Bluetooth mode (press the button).
[PLAY MODE] button
5
[SEARCH MODE] button
(KDC-X794/ KDC-MP745U)
Enters Play mode Menu (press the button).
To enter Bluetooth mode (press the button at least 1
second).
To enter Search mode (iPod), move between folders
(Audio file), etc. For more details, see operations of
each source described in page 8 or later.
6
Microphone (KDC-X994/ KDC-BT945U)
12 Display window
The microphone for the hands free phone is supplied.
When your voice cannot be recognized due to the
low microphone volume or noises in the vehicle,
adjust the microphone settings by <Bluetooth
13 [FAV] button
To recall a registered favorite item (press the button).
To register to Favorite (press the button at least 1
second).
14 USB Terminal
A USB device or an iPod can be connected.
7
Auxiliary Input Terminal
Portable audio device can be connected with the
mini-plug (3.5 mm ø).
• Use the mini-plug cable which is stereo type and does not
have any resistance.
|
6
KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
General operation
Before Using
Menu List Operation
The basic operating procedure for using this
function is described below. The individual function
items are covered in the operating procedures.
Exit of the Demonstration Mode
Turn off the demonstration mode when you use it
for the first time after installation.
1
Select the source
1
2
Press the [VOL] knob to quit the demonstration
mode when the messages “To cancel Demo
press the volume knob” are displayed (approx. 15
seconds).
Press the [SRC] button. Turn the [VOL] knob
and press it when the desired item is displayed.
Function items vary from source to source. For a list
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
Turn the [VOL] knob to select “YES” and press the
[VOL] knob.
2
3
Enter Menu List mode
Press the [MENU] button.
⁄
• Demonstration mode can also be cancelled in “DEMO
Mode” of Menu List mode. Refer to <Demonstration mode
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
Repeat the operation until your desired setup item
is selected.
Common Operation
✍ Press the [MENU] button to return to the
previous item.
Operation example:
Power and source select
Turns the power ON by pressing the [SRC]
button.
When the power is ON, select a source.
• SRC Select mode 1: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
• SRC Select mode 2: Pressing the [SRC] button
each time switches between sources.
Tuner (“TUNER” or “HD RADIO”) ➜ Bluetooth
Audio (“BT AUDIO”) (KDC-X994, KDC-BT945U
only) ➜ USB (“USB”) or iPod (“iPod”) ➜ CD
(“CD”) ➜ Auxiliary input (“AUX”) ➜ Standby
(“STANDBY”) ➜ Tuner...
4
1[VOL]
3[MENU]
3
2
Music
3
2
PlayLists
My
Best 25
1
1
Artists
Albums
[VOL]
[MENU]
2
4
1 sec.
Play Mode
In this manual, the above selection is indicated as
Select “Music” > “Playlists” > “My Best 25”.
Keeping pressing the [SRC] button for at least 1
second turns the power OFF.
4
5
Make a setting
• When the “
” icon is displayed (at the
PUSH
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
⁄
• When the “
” icon is not displayed
PUSH
• Auxiliary input source is initially set to “OFF”. Set “Built in
• When an optional accessory is connected, the source name
for each device appears.
• When connection of the iPod is recognized, the source
display changes from “USB” to “iPod”.
Press the [4] or [¢] button to select a
setting value.
Exit Menu List mode
Press the [MENU] button for at least 1 second to
return to the first hierarchy. Press the [MENU]
button in the first hierarchy to exit the Menu
List mode.
Volume
Turning the [VOL] knob adjusts the sound
volume.
⁄
• You cannot set the item with the “ ” icon displayed.
English
|
7
iPod/iPhone Operation
SRC MENU VOL DISP
SEARCH MODE
KCA-iP101 (optional
accessory) is required to
connect an iPod.
4
38
¢
/PLAY MODE
2
3
Enter Menu List mode
Press the [MENU] button.
Basic Operation
Playing iPod
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music”.
• Connect an iPod
When connected, the source is switched
automatically and a song starts playing.
4
Select a song
• Select iPod source
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [SRC] button. Turn the [VOL]
knob and press it when the desired item is
displayed.
High Speed Search
Press the [DISP] or [ ] / [PLAY MODE]
button to scroll up or down by a page.
Press the [DISP] or [ ] / [PLAY MODE]
button for at least 1 second to continuously
scroll up or down at high speed. Press the
button again to stop scrolling.
Press the [MENU] button.
Press the [MENU] button for at least 1
second.
Select the “iPod” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
Song Select
Press the [4] or [¢] button.
Return to previous item
Return to Top menu
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
✍ For example: Searching by Artist name.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music” > “Artists” > Artist name > Album
name > Song title
Pause and Play
Press the [38] button to pause or resume
playback.
Remove iPod
Press the [38] button for at least 2 seconds.
The unit enters the USB REMOVE mode (“USB
REMOVE” is displayed.), and the iPod can be
removed safely.
Cancelling Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
• The unit memorizes the position where you have
found a song in the Search mode. When you enter the
Menu List mode after searching a song, the memorized
position is displayed. Press the [MENU] button for at least
1 second to move to the first hierarchy, select a Menu
item, and set it’s parameters.
• Characters which cannot be displayed are left blank. If
non of the characters can be displayed, the browse item
name and digits are displayed.
Selecting a song by browsing iPod
Display
Items
“Music”
“Playlists”
“Artists”
Playlists
Artists
“Albums”
“Songs”
Albums
Songs
Items
Playlists
Artists
Albums
Songs
Display
“PLIST***” Podcasts
“ART***”
“ALB***”
“PRGM***”
Items
Display
“Podcasts”
“Genres”
Podcasts
Genres
“PDCT***”
“GEN***”
“COM***”
Genres
Composers
“Composers”
Composers
1
Select iPod source
|
8
KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Play Mode
⁄
• In the iPod Control by Hand Mode, iPod cannot be
operated using this unit.
• This mode is not compatible with music information
display. The display will show “iPod by Hand Mode”.
• iPod can be operated when it conforms to the iPod
control function.
You can select a Play Mode, such as Random play
and Repeat play.
1
2
Select iPod source
Enter Play Mode Menu
KDC-X994 KDC-BT945U
Press the [VOL] knob for at least 1 second.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button.
✍ You can also select from “Play Mode” in Menu
List mode.
iPod Setting
You can select following iPod Setting items.
1
2
Select iPod source
Enter Menu List mode
Press the [MENU] button.
3
Select the Play Mode
Turn the [VOL] knob.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”.
Display
“iPod by Hand”
Overview
When set to“ON”, allows you to operate iPod
with the control on the iPod.
“ON”/ “OFF”
When set to“ON”, plays the music in the folder
randomly.
“ON”/ “OFF”
When set to“ON”, plays all songs in iPod
randomly.
4
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
“Folder Random”
“All Random”
“File Repeat”
Display
Overview
“Settings”
“ON”/ “OFF”
When set to“ON”, plays the music repeatedly.
“ON”/ “OFF”
“Skip Search”
Sets the ratio of skip performed with <Skip
“0.5%”/ “1%”/ “5%”/ “10%”
Deletes the registered My Playlist.
Refer to <Deleting a Song from the Playlist>
(page 12) for the operation.
(
: Factory setting)
“Delete My
Playlist”
4
5
Make a setting
Press the [4] or [¢] button.
“One”/ “All” ➜ “Yes”/ “No”
Exit Play Mode Menu
KDC-X994 KDC-BT945U
Press the [MENU] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button.
(
: Factory setting)
5
6
Make a setting
• When the “
” icon is displayed (at the
PUSH
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
” icon is not displayed
Press the [4] or [¢] button to select a
Remarks
• All Random
• When the “
PUSH
• The time required to turn on the all random function
may become longer depending on the number of songs
in iPod.
• Turning on the all random function changes the iPod
browse item to “Songs”. This browse item will not be
changed even if the all random function is turned off.
• If the browse item is changed to search for music while
the all random function is on, the all random function is
turned off and the songs in the browse item are played
at random.
setting value.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
Changing the setting of one reflects the other.
• iPod by Hand (iPod Control by Hand Mode)
Allows you to operate iPod with the control on the iPod.
English
|
9
iPod/iPhone Operation
Selecting the Search mode
Direct Search
You can select the most suited search method for
the desired song from 4 types of the Search mode.
You can quickly search the desired song by
specifying its Search item (artist, album, etc.) and
initial.
Normal playing
1
2
Select iPod source
Display
Overview
Press the [SEARCH MODE] button.
“Direct Search”
You can quickly search the desired song by
specifying its Search item (artist, album, etc.)
and initial.
3
Enter Direct Search mode
Turn the [VOL] knob and press it when the
Searches for music of the same artist or genre
as the one being played.
desired item is displayed.
Select “Direct Search”.
“Related Search”
Registers a song to My Playlist and play it.
4
Select the Search item
Turn the [VOL] knob and press it when the
desired Search item is selected.
“Recall My Playlist”
“Delete My Playlist”
“Register My P-list”
Display
Items
Playlists
Artists
Albums
Songs
Display
“PODCASTS”
“GENRES”
Items
Podcasts
Genres
Browsing
“PLAYLISTS”
“ARTISTS”
“ALBUMS”
“SONGS”
Display
“Direct Search”
Overview
“COMPOSERS” Composers
You can quickly search the desired song by
specifying its Search item (artist, album, etc.)
and initial.
You can select an alphabetic character from
the list in the Search item (artist, album, etc.)
selected now.
The number of songs to be skipped is
determined by the ratio of the total number of
songs in the list which is selected now.
Registers a song to My Playlist.
5
6
Select the character to be searched for
“Alphabet Search”
“Skip Search”
Operation type
Operation
Move between items
Select an item
Move to the next column
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [4] or [¢] button.
Up to 3 characters can be entered.
Determine the selected initial
Turn the [VOL] knob and press it when the
desired item is displayed.
“Register My P-list”
Select “DONE”.
1
Select iPod source
Start search. When search is completed, the music
search mode is selected again at the selected
character position.
After this step, you need to browse. See step 4 of
select a song.
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select the “iPod” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
2
3
4
Enter Search mode
Press the [SEARCH MODE] button.
Cancelling the Direct Search
Press the [SEARCH MODE] button.
Select the Search mode
Turn the [VOL] knob.
⁄
• Characters that can be entered are alphabetical
characters (A to Z), numerical characters(0 to 9), and “ * ”.
• “ * ”indicates characters other than alphabetical and
numerical characters. You cannot enter any more
characters when entering “ * ”in the first character
position.
Start the search mode
Press the [VOL] knob.
Cancelling Search mode
Press the [SEARCH MODE ] button.
• If the first character string begins with an article “a”, “an”,
or “the” in the Direct Search mode, it is searched for in
defiance of the article.
|
10 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Related Search
Alphabet Search
Searches for music of the same artist or genre as the
one being played.
You can select a song by alphabet. This function
searches songs whose name contain the specified
character(s) in the list of the selected Search item
(artist, album, etc).
1
2
Play the music in iPod
Press the [SEARCH MODE] button.
1
2
Select iPod source
3
Enter Related Search mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Enter browsing mode
Press the [MENU] button.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music” > item.
Select “Related Search”.
4
Select the Search item
Turn the [VOL] knob and press it when the
3
4
Enter Alphabet Search mode
Press the [SEARCH MODE] button.
Turn the [VOL] knob and press it when the
desired item is displayed.
desired Search item is selected.
Display
Searches music
“Search Artist”
“Search Album”
Displays the album of the same artist.
Displays music in the album in which the one
being played is included.
Select “Alphabet Search”.
“Search Genre”
Displays the artist of the same genre.
Search for item
“Search Composer” Displays the album including music created by the
same Composer.
Operation type
Operation
Select the character
Press the [DISP] or [ ] / [PLAY MODE]
button.
After this step, you need to browse. See step 4 of
select a song.
Move between items
Select an item
Return to previous item
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [MENU] button.
Cancelling the Related Search
Press the [SEARCH MODE] button.
After this step, you need to browse. See step 4 of
select a song.
⁄
• Related search cannot be performed while playing the
Podcast.
Cancelling the Alphabet Search
Press the [SEARCH MODE] button.
• When the music being played has no information on
browsing items or no music was found, “Not Found” is
displayed.
⁄
• The time of search by alphabet may become long
depending on the number of songs or items in iPod.
• If the first character string begins with an article “a”, “an”,
or “the” in the Alphabet Search mode, it is searched for in
defiance of the article.
English
|
11
iPod/iPhone Operation
Skip Search
My Playlist
You can scroll up or down according to the number
of the selected Search items so that you can quickly
switch the display position.
Allows you to register your favorite songs in the
Playlist of this unit. You can register up to 10 songs
in the Playlist.
1
2
Select iPod source
Registering Songs in the Playlist
Enter browsing mode
1
2
Play the song you want to register
Press the [MENU] button.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music” > item.
Press the [SEARCH MODE] button.
3
Register the song
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Register My Playlist”.
“## Stored (Registration number)” is displayed.
3
4
Press the [SEARCH MODE] button.
Enter Skip Search mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Skip Search”.
⁄
• Make a Playlist from the songs stored in one iPod. If you
attempt to register a song stored in a different iPod,
”No Information” appears and then ”Delete My Playlist”
appears. Select “Yes” to delete the Playlist when you want
to remake it.
5
Search for item
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [DISP] or [ ] / [PLAY MODE]
button.
• The song displayed in the Music Search mode can be
registered in the same manner. For how to use the music
search function, refer to <Selecting a song by browsing
Skip Search
Keep pressing the button for 3 seconds or
longer skips songs at 10% irrespective of
the setting.
• If you attempt to register the eleventh song, ”Memory
Full” appears and you cannot register it accordingly. To
register the song, delete an unnecessary song.
• Do not register Podcasts. Songs you do not want to
register may be registered, or playback may not be
carried out correctly.
Sets the ratio of skip
performed
Return to previous item
Press the [
4] or [¢] button.
Press the [MENU] button.
After this step, you need to browse. See step 4 of
select a song.
Playing the Song in the Playlist
1
2
Press the [SEARCH MODE] button.
Enter My Playlist mode
Turn the [VOL] knob and press it when the
Cancelling the Skip Search
Press the [SEARCH MODE] button.
desired item is displayed.
Select “Recall My Playlist”.
⁄
•
3
Play the song in the Playlist
Turn the [VOL] knob and press it when the
9).
desired item is displayed.
Select the song you want to play.
⁄
• Turning ACC OFF or the power OFF cancels the My
Playlist mode.
• The ending of a song may be cut unless the song has a
silence of 1 second or longer at the end.
• Random play cannot be performed during playback of a
song in the Playlist.
Deleting a Song from the Playlist
Press the [SEARCH MODE] button.
1
|
12 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
2
3
Enter Delete Playlist mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Delete My Playlist”.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select ”Delete One” or ”Delete All”.
Selecting “Delete All” moves to step 5 and all songs
are deleted.
4
5
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the song you want to delete.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select ”Yes”.
“Complete” is displayed.
⁄
• You can also delete all songs from the Playlist by
selecting “Delete My Playlist” described in <iPod Setting>
• If you connect the different iPod from one registered to
My Playlist, “Delete One” and “Delete All” will not appear
and all songs be deleted.
English
|
13
USB device Operation
When connecting the
USB device, usage of
the CA-U1EX (option) is
recommended.
SEARCH MODE
SRC MENU VOL
DISP
4
38
¢
/ PLAY MODE
Basic Operation
File Search
Selecting the file you want to listen to from the
device being played now.
Playing USB device
• Connect a USB device
When connected, the source is switched
USB device
automatically and a song starts playing.
Display
Items
“Music”
Folder or file name list.
• Select USB source
Press the [SRC] button. Turn the [VOL]
knob and press it when the desired item is
displayed.
Music Editor media
Display
Items
“Music”
Select the “USB” display.
“Playlists”
Playlists
Artists
Albums
Songs
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
“Artists”
“Albums”
“Songs”
“Genres”
Moving to the next folder
Press the [SEARCH MODE] button.
Genres
Song Select
Press the [4] or [¢] button.
1
2
Select USB source
Enter Menu List mode
Press the [MENU] button.
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music”.
⁄
• No sound is output while playing audio file.
Pause and Play
Press the [38] button to pause or resume
playback.
4
Select a file
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [DISP] or [ ] / [PLAY MODE]
button to scroll up or down by a page.
Press the [DISP] or [ ] / [PLAY MODE]
button for at least 1 second to continuously
scroll up or down at high speed. Press the
button again to stop scrolling.
Remove USB device
Press the [38] button for at least 2 seconds.
The unit enters the USB REMOVE mode (“USB
REMOVE” is displayed.), and the USB device can be
removed safely.
High Speed Search
Return to previous item
Return to Top menu
Press the [MENU] button.
Press the [MENU] button for at least 1
second.
✍ For example: Searching for ¡".
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music” > 1 > 2 > ¡"
|
14 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
USB Setting
1
2
You can select following USB Setting items.
¡"
¡#
¡!
1
2
Select USB source
Enter Menu List mode
Press the [MENU] button.
Cancelling Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
⁄
Select “Settings”.
• When you search a song in the File Search mode, the
unit memorizes the position of the song being played
after the search. To set a different Menu item after
searching a song, press the [MENU] button for at least 1
second to move to the first hierarchy.
4
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
Overview
“Settings”
“Skip Search”
Play Mode
Sets the ratio of skip performed with <Skip
“0.5%”/ “1%”/ “5%”/ “10%”
You can select a Play Mode, such as Random play
and Repeat play.
(
: Factory setting)
1
2
Select USB source
5
6
Make a setting
Press the [4] or [¢] button.
Enter Play Mode
KDC-X994 KDC-BT945U
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Press the [VOL] knob for at least 1 second.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button.
✍ You can also select from “Play Mode” in Menu
List mode.
⁄
Changing the setting of one reflects the other.
3
Select the Play Mode
Turn the [VOL] knob.
Display
Overview
“File Scan”
When set to“ON”, plays the intro of the music in
the folder successively.
“ON”/ “OFF”
“Folder Random”
When set to“ON”, plays the music in the folder
randomly.
“ON”/ “OFF”
“File Repeat”
When set to“ON”, plays the music repeatedly.
“ON”/ “OFF”
“Folder Repeat”
When set to“ON”, plays the music in the folder
repeatedly.
“ON”/ “OFF”
(
: Factory setting)
4
5
Make a setting
Press the [4] or [¢] button.
Exit Play Mode
KDC-X994 KDC-BT945U
Press the [MENU] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button.
English
|
15
USB device Operation
Function of remote control
Skip Search
Direct Music Search
You can scroll up or down according to the number
of the selected Search items so that you can quickly
switch the display position.
Searching the music by entering the file number.
1
2
3
Enter Direct Music Search mode
Press the [DIRECT] button on the remote
control.
1
2
Select USB source
Enter File Search mode
Press the [MENU] button.
Enter the music number
Press the number buttons on the remote
control.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music” > item.
Search the music
Press the [4] or [¢] button.
3
4
Enter Skip Search mode
Press the [SEARCH MODE] button.
Cancelling Direct Music Search
Press the [DIRECT]] button.
Search for music
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
⁄
• Direct Music Search cannot be performed during playing
of “Music Editor” media, Random play, or scan play.
Skip Search
Press the [DISP] or [ ] / [PLAY MODE]
button.
Keep pressing the button for 3 seconds or
longer skips songs at 10% irrespective of
the setting.
Sets the ratio of skip
performed
Press the [
4] or [¢] button.
Return to previous item
Press the [MENU] button.
After this step, see step 4 of <File Search> (page 14)
to select a song.
Cancelling the Skip Search
Press the [SEARCH MODE] button.
⁄
• This operation is effective only for the files registered in
the database created with KENWOOD Music Editor.
|
16 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Music CD/ Audio file Operation
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
Release MENU VOL DISP
SEARCH MODE
⁄
• No sound is output while playing audio file.
Pause and Play
Press the [38] button to pause or resume
playback.
SRC 4 38
¢
/PLAY MODE
Function of Internal CD source
Basic Operation
Music Search
Drop open the faceplate
Press the Release button.
Selecting the music you want to listen to from the
disc being played now.
⁄
Display
“Music”
Overview
• Push the faceplate on the left side, and return it to its
Track list (Music CD) / Folder or file name list
(Audio file)
former position.
Disc play
• A disc inserted.
1
2
Select CD source
Enter Menu List mode
Press the [MENU] button.
When inserted, the source is switched
automatically and a song is starts playing.
When a CD is inserted, the “CD-IN” indicator
is ON.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music”.
4
Search for music
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
High Speed Search
Press the [DISP] or [ ] / [PLAY MODE]
button to scroll up or down by a page.
Press the [DISP] or [ ] / [PLAY MODE]
button for at least 1 second to continuously
scroll up or down at high speed. Press the
button again to stop scrolling.
• Select CD source
Press the [SRC] button.Turn the [VOL]
knob and press it when the desired item is
displayed.
Select the “CD” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
Return to previous item
Return to Top menu
Press the [MENU] button.
Press the [MENU] button for at least 1
second.
Disc ejection
Press the [0] button.
Cancelling Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Moving to the next folder
Press the [SEARCH MODE] button.
⁄
• This operation can be performed only for the Audio file.
Song Select
Press the [4] or [¢] button.
English
|
17
Music CD/ Audio file Operation
“Track Repeat”
“Disc Repeat”
When set to“ON”, plays the music repeatedly.
“ON”/ “OFF”
When set to“ON”, plays the music on the disc
repeatedly.
Play Mode
You can select a Play Mode, such as Random play
and Repeat play.
“ON”/ “OFF”
1
2
Select CD source
(
: Factory setting)
Enter Play Mode
KDC-X994 KDC-BT945U
4
5
Make a setting
Press the [4] or [¢] button.
Press the [VOL] knob for at least 1 second.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button.
✍ You can also select from “Play Mode” in Menu
List mode.
Exit Play Mode
KDC-X994 KDC-BT945U
Press the [MENU] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button.
3
Select the Play Mode
Turn the [VOL] knob.
Basic Operation of Disc Changer
(Optional)
Music CD source
Display
Overview
“Track Scan”
When set to“ON”, plays the intro of the music on
the disc successively.
Select CD changer source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select the “CD CHANGER” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
“ON”/ “OFF”
When set to“ON”, plays the music on the disc
randomly.
“ON”/ “OFF”
When set to“ON”, plays the music repeatedly.
“ON”/ “OFF”
“Disc Random”
“Track Repeat”
Moving to the next disc
Press the [SEARCH MODE] button.
(
: Factory setting)
Audio file source
Song Select
Press the [4] or [¢] button.
Display
“File Scan”
Overview
When set to“ON”, plays the intro of the music on
the disc successively.
“ON”/ “OFF”
When set to“ON”, plays the music on the disc
randomly.
“ON”/ “OFF”
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
“Folder Random”
Pause and Play
Press the [38] button to pause or resume
playback.
“File Repeat”
When set to“ON”, plays the music repeatedly.
“ON”/ “OFF”
“Folder Repeat”
When set to“ON”, plays the music on the disc
repeatedly.
“ON”/ “OFF”
(
: Factory setting)
Disc changer source
Display
Overview
“Track Scan”
When set to“ON”, plays the intro of the music on
the disc successively.
“ON”/ “OFF”
“Disc Random”
When set to“ON”, plays the music on the disc
randomly.
“ON”/ “OFF”
“Magazine Random When set to“ON”, plays the music in the disc
changer randomly.
“ON”/ “OFF”
|
18 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Function of remote control
Direct Music Search
Searching the music by entering the track number.
1
2
3
Enter Direct Music Search mode
Press the [DIRECT] button on the remote
control.
Enter the music number
Press the number buttons on the remote
control.
Search the music
Press the [4] or [¢] button.
Cancelling Direct Music Search
Press the [DIRECT] button.
⁄
• Direct Music Search cannot be performed during playing
of Random play or scan play.
Function of disc changer with remote control
Direct Disc Search
Searching the disc by entering the disc number.
1
2
3
Enter Direct Disc Search mode
Press the [DIRECT] button on the remote
control.
Enter the disc number
Press the number buttons on the remote
control.
Search the disc
Press the [FM] or [AM] button.
Cancelling Direct Disc Search
Press the [DIRECT] button.
⁄
• Direct Disc Search cannot be performed during Random
play or scan play.
• Input “0”to select disc 10.
English
|
19
Tuner Operation
“Auto Memory” Memorizes 6 stations with good reception
automatically.
SRC MENU VOL
Refer to <Auto Memory Entry> (page 21)
“TI”
Switches to the traffic information automatically
when the traffic bulletin starts. (KDC-X994/
KDC-X794 only)
“OFF”/ “ON”
“Forced MONO” You can reduce the noise when stereo broadcasts
4
¢
are received as monaural.
“OFF”/ “ON”
(
: Factory setting)
Basic Operation
5
6
Make a setting
Selecting Tuner source
Press the [4] or [¢] button.
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select the “Tuner” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Remarks
• Forced MONO
Selecting the Receiving Band
1. Enter Menu List mode
Strong electrical fields (such as from power lines) may
cause unstable sound quality when it is set to ON. In such
a situation, turn it OFF.
Press the [MENU] button.
2. Turn the [VOL] knob and press it when the
desired item is displayed.
Select “FM1”, “FM2”, “FM3” or “AM”.
• Traffic information (TI)
Turns ON or OFF the Traffic Information function.
When the function is set to ON, “TI” indicator is ON.
If traffic bulletin starts when the function is ON,
“Traffic INFO” is displayed and traffic information is
received.
If the volume is adjusted during reception of traffic
information, the adjusted volume is memorized
automatically. The memorized volume will be applied next
time the Traffic Information function is turned ON.
Selecting the Receiving station
Press the [4] or [¢] button.
✍ Details of the station selecting in operation are
set in the “Seek Mode” of <Tuner Setting> (page
20).
Tuner Setting
You can select following Tuner Setting items.
1
2
Select Tuner source
Enter Menu List mode
Press the [MENU] button.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”.
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
Overview
“Settings”
“Seek Mode”
Selects the tuning mode of the radio.
“Auto1”: Automatic search for a station.
“Auto2”: Search in order of the stations in the
Preset memory.
“Manual”: Normal manual tuning control.
|
20 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Station Preset Memory
Preset Tuning
Putting a station in the memory.
Recalling the stations in the memory.
1
Select the radio band and tune in a desired
radio station you wish to store in the preset
memory
1
2
Select the radio band
Select a desired station in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
2
3
Enter Menu List mode
Press the [MENU] button.
Select “List & Memory” > Preset number.
Enter Preset Memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Function of remote control
Direct Access Tuning
Select “List & Memory”.
Tuning in a desired radio station by entering the
frequency.
4
Select the number to put in the memory
Turn the [VOL] knob and press it for at least 2
seconds when the desired item is displayed.
Select a preset number.
1
2
Select the radio band
Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
Display
“List & Memory”
“-1”
Overview
“– – – –” is displayed.
Preset number 1.
Preset number 2.
3
Enter the frequency
Press the number buttons on the remote
“-2”
control.
“-6”
Preset number 6.
Example:
Cancelling the Preset Memory mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Desired frequency Press button
92.1 MHz (FM)
810 kHz (AM)
[9], [2], [1]
[8], [1], [0]
4
Tune in to the entered frequency
Press the [4] or [¢] button.
Auto Memory Entry
Putting stations with good reception in the memory
automatically.
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
1
2
3
Select the radio band you wish to store in the
preset memory
Enter Menu List mode
Press the [MENU] button.
Enter Auto Memory Entry mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Auto Memory”.
4
Open Auto Memory Entry
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
When 6 stations that can be received are put in the
memory, auto memory entry closes.
English
|
21
Tuner Operation
Function of KDC-X994/KDC-X794
Function of KDC-X994/KDC-X794
PTY (Program Type)
Program Type Preset
Selecting the Program Type below and searching
for a station.
Putting the Program Type in the Preset button
memory and quick recall.
Program Type Display
Program Type Display
Presetting the Program Type
Speech
Music
News
“Speech”
“Music”
“News”
Soft
“Soft”
1
2
3
Select the Program Type to preset
Nostalgia
Jazz
“Nostalga”
“Jazz”
Information
Sports
Talk
“Inform”
“Sports”
“Talk”
Classical
R & B
“Classicl”
“R & B”
Enter Program Type Preset mode
Press the [SEARCH MODE] button.
Soft R & B
Language
“Soft R&B ”
“Language”
Select the number to put in the memory
Turn the [VOL] knob and press it for at least 2
seconds when the desired item is displayed.
Select preset number.
Rock
“Rock”
Classic Rock
Adult Hits
Soft Rock
Top 40
Country
Oldies
“Cls Rock”
“Adlt Hit”
“Soft Rck”
“Top 40”
“Country”
“Oldies”
Religious Music “Rel Musc”
Religious Talk “Rel Talk”
Personality
Public
“Persnlty”
“Public”
Recalling the preset Program Type
College
Weather
“College”
“Weather”
1
2
3
Enter PTY mode
• Speech and Music include the Program type shown
below.
Speech: Items in the white letters.
Music: Items in the black letters.
Enter Program Type Preset mode
Press the [SEARCH MODE] button.
Select a desired Program Type in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
1
2
Enter Menu List mode
Press the [MENU] button.
Select preset number.
Select the FM band
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “FM1”, “FM2”, or “FM3”.
3
4
Enter Menu List mode
Press the [MENU] button.
Enter PTY mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “PTY Search”.
5
6
7
Select the Program Type
Turn the [VOL] knob.
Search for the selected Program Type station
Press the [4] or [¢] button.
Exit PTY mode
Press the [MENU] button.
⁄
• This function cannot be used during a traffic bulletin or
AM reception.
• When the selected Program Type is not found, “No PTY”
is displayed. Select another Program Type.
•
The operation ends automatically if you do not operate
within 30 seconds.
|
22 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Function of KDC-X994/ KDC-BT945U
KDC-X794/ KDC-MP745U with BT200 (Optional Accessory)
Bluetooth Audio Operation
Basic Operation
SRC MENU VOL
Selecting Bluetooth Audio source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select the “BT Audio” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
4
38
¢
/PLAY MODE
Pause and play
Press the [38] button.
Connecting a Bluetooth Device
Music Search
Press the [4] or [¢] button.
Before use the Bluetooth device, you need to
connect Bluetooth device to this unit.
⁄
Pairing (Registering from Bluetooth devices)
To make your Bluetooth Audio player usable with
this unit, you need to register it (pairing).
• All or some of the operations above cannot be
performed if the Bluetooth audio player is not ready for
remote control.
1
Turn on this unit
Press the [SRC] button.
• Switching to the Bluetooth audio source does not start
or stop playback automatically. Perform the operation for
starting or stopping playback.
• Some audio players cannot be controlled remotely or
reconnected after Bluetooth disconnection. Operate the
main unit of the audio player to connect Bluetooth.
2
Start registering this unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
audio player (pairing). Select “KENWOOD BT CD/R-
4P1”/ “KCA-BT200”from the list of connected units.
3
4
Enter a PIN code
Input the PIN code (“0000”) in the Bluetooth
device.
Check that registration is complete on the
Bluetooth device.
✍ PIN code is set to “0000”as the default. You can
change this code. Refer to <Registering PIN
By operating the Bluetooth device, start
Bluetooth connection.
⁄
• If pairing does not succeed, try followings.
– Turn off the power of this unit and turn it back on. And
then try the pairing operation again.
– If other audio players have been registered, delete
them. And then try the pairing operation again. See
• For details on the Bluetooth Audio player which can be
connected, see <About the Bluetooth Audio player>
English
|
23
Function of KDC-X994/ KDC-BT945U
KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory)
Operation of hands-free phoning
SRC MENU VOL
SEARCH MODE
⁄
• For details on the Bluetooth cell-phone with the hands-
Receiving a Call
4
38
¢
/PLAY MODE
Answering a Phone Call
Connecting a Bluetooth Device
Press the [VOL] knob.
⁄
Before use the Bluetooth device, you need to
connect Bluetooth device to this unit. The following
3 steps procedure is necessary.
• The following operations disconnect the line:
- Insert a CD.
- Connect a USB device.
Step 1. Pairing (Registering from Bluetooth
devices)
• The name of the calling party is displayed if it has already
been registered in the Phone Book.
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing).
Rejecting an Incoming Call
Press the [SRC] button or press the [ ] / [PLAY
MODE] button for at least 1 second.
1
2
Turn on this unit
Press the [SRC] button.
Start registering this unit by operating the
Bluetooth device
During a Call
By operating the Bluetooth device, register the
hands-free unit (pairing). Select “KENWOOD BT
CD/R-4P1”/ “KCA-BT200”from the list of connected
units.
Disconnecting a Call
Press the [SRC] button or press the [ ] / [PLAY
MODE] button for at least 1 second.
Switching to the Private Mode
Press the [38] knob.
Switches between Private talk (“PRIVATE”) and
Hands-free talk each time this button is pressed.
3
Enter a PIN code
Input the PIN code (“0000”) in the Bluetooth
device.
Check that registration is complete on the
Bluetooth device.
✍ PIN code is set to “0000”as the default. You can
change this code. Refer to <Registering PIN
⁄
• Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection.
If this happens, the source cannot be switched back to
the hands-free talk mode by operating this unit. Operate
your cell-phone to return to the hands-free talk mode.
4
By operating the Bluetooth device, start hands-
free connection.
Adjusting the Voice Volume during a Call
Turn the [VOL] knob.
Step 2. Connection
If you have registered 2 or more cell-phones, you
need to select one of them. For more details,
Call Waiting
When a cell-phone is connected, the “BT” indicator
is light up.
Answering Another Incoming Call with the
Current Call Suspended
Step 3. Hands-free phoning
You can do hand-free phoning when the
connection is made.
1
2
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “ANSWER”.
|
24 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Answering another Incoming Call after
Terminating the Current Call
Press the [SRC] button.
below.
3
Exit the dialing method mode
KDC-X994 KDC-BT945U
Continuing the Current Call
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
1
2
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “REJECT”.
Speed Dialing (Preset Dial)
Answering the Waiting Call after Terminating
the Current Call
Press the [SRC] button.
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
Switching between the Current Call and Waiting
Call
Press the [VOL] knob.
Each pressing of this knob switches the calling
party.
2
3
Select the preset dial mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Other Functions
Select “Preset call”.
Clearing the Disconnection Message
KDC-X994 KDC-BT945U
Select the number you want to recall from the
memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select preset number.
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
“HF Disconnect” disappears.
Phone number is displayed.
4
5
Exit the preset dial mode
Press the [MENU] button.
Making a Call
Make a call
Press the [VOL] knob.
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
⁄
• You need to register the preset dial number. Refer to
2
Select a dialing method
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
Overview
“Preset Call”
Calling a number in the preset.
“Phonebook” Selecting the initial to be searched for the phone
book.
“In Call”
“Out Call”
Calling a number in the incoming call list.
Calling a number in the outgoing call list.
“Missed Call” Calling a number in the missed calls list.
“Number Dial” Making a call by entering phone number.
Operation method of each mode is described
English
|
25
Function of KDC-X994/ KDC-BT945U
KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory)
Operation of hands-free phoning
3
Select a name or phone number
Turn the [VOL] knob and press it when the
desired item is displayed.
✍ Switching between Display Modes
Press the [DISP] button.
Calling a Number in the Phone Book
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
Pressing this button each time switches between
name and telephone number.
4
Make a call
Press the [VOL] knob.
2
3
Select the Phone Book mode
Turn the [VOL] knob and press it when the
desired item is displayed.
⁄
• The outgoing call list and the incoming call list, and the
missed call list are the lists of calls originated from and
received at this unit. They are not the ones stored in the
cell-phone memory.
Select “Phonebook”.
Select the initial to be searched for
Operation type
Move to the next character. Turn the [VOL] knob.
Move to the next row. Press the [ ] or [
Determine the selected initial. Press the [VOL] knob for at least 1
second.
Operation
4
¢] button.
Dial a Number
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
4
5
Select the name
Operation type
Move to the next phone
number.
Determine the selected phone Press the [VOL] knob.
number.
Operation
Turn the [VOL] knob.
2
3
Select the number dial mode
Turn the [VOL] knob and press it when the
desired item is displayed.
✍ Switching between Display Modes
Press the [DISP] button.
Pressing this button each time switches between
Select “Number Dial”.
name and telephone number.
Enter a phone number
Operation type
Operation
Make a call
Press the [VOL] knob.
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Press the [
Press the [
¢
] button.
] button.
⁄
4
• During search, a non-accent character such as “u”is
searched for instead of an accent character such as “ü”.
• Press the number ([1] – [0]), #([FM]), *([AM]), or
+([¢]) button on the remote controller.
✍ To erase the entered phone number digit
by digit:
Calling a Number in the Call log
Press the [4] button on the remote
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
controller.
4
Make a call
• Press the [VOL] knob.
• Press the [DIRECT] button on the remote
controller.
2
Select the call log mode
Turn the [VOL] knob and press it when the
⁄
• You can input max 32 digits.
desired item is displayed.
Select “Out Call” (outgoing call), “In Call”
(incoming call), or “Missed Call” (missed call).
|
26 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Function of KDC-X794/ KDC-MP745U
Registering to the Preset Dial Number
List
Make a Voice Dialing Call
1
2
Enter voice recognition mode
Press the [VOL] knob for at least 1 second.
1
Select the phone number you wish to register
Select the phone number with reference to the
following:
“PB Name?” is displayed.
When a beep is heard, say the name within 2
seconds.
2
3
Enter Preset Memory mode
Press the [VOL] button for at least 2 seconds.
3
4
“PN Type” is displayed.
When a beep is heard, say the category name
within 2 seconds.
Select the Preset number to put in the
memory
Turn the [VOL] knob and press it for at least 1
second when the desired item is displayed.
Select preset number.
Make a call
Press the [VOL] knob.
✍ This step is the same as step 4 of the procedure
26). You can make a call or select a category.
4
Determine the Preset number to put in the
memory
Turn the [VOL] knob and press it when the
⁄
• If your voice cannot be recognized, a message is
displayed. Pressing the [VOL] knob allows you to retry
• Both the name and category require registration of
a voice tag. Refer to <Setting a Voice Command for
desired item is displayed.
Exit the Preset Memory mode
Press the [MENU] button.
• Audio sound is not output during voice recognition.
Display of Phone Number type
(category)
The category items in the Phone Book are displayed
as follows:
Display
Information
“GENERAL”/“
”
General
“HOME”/“
“OFFICE”/“
“MOBILE”/“
“OTHER”/“
”
Home
Office
Mobile
Other
”
”
”
English
|
27
Display Settings
Display Setting
SRC MENU VOL
You can select following Display Setting items.
1
Select the source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
4
¢
2
3
Enter Menu List mode
Press the [MENU] button.
Basic Operation
Enter Display Setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “DISP & ILLUMI”.
Switching display
Press the [DISP] button.
Mode
Display Type
5-line display mode Displays 4 to 5 lines of text.
3-line display mode Displays 2 to 3 lines of text.
iPod-like display Displays like iPod. (iPod source only)
mode
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
Spectrum analyzer Displays a line of text and the spectrum analyzer.
display mode
Clock display mode Displays the clock.
Display
“Settings”
Overview
“DISP & ILLUMI” Making Display and Illumination settings.
“Display Select” Selecting and customizing the Display type.
“Color Select” Selecting the Illumination Color of the panel.
Refer to <Illumination Color Selection>
⁄
• When the 5-line display mode is selected, the status (ON/
OFF indicator of each function) can be displayed on the
first line, and the icon of the currently selected source and
the text information title can be displayed on the left side
by the following <Customization of 5-line Display Mode
operation.
“Display Off
Mode”
If this unit is not operated at least 5 seconds
with“OFF”selected, the display turns off. During
a setup mode, the display will not turn off even
if 5 seconds lapse.
“OFF”/ “ON”
Status display: Select “Settings” > “DISP & ILLUMI” > “Display
Select” > “Status”
Side display: Select “Settings” > “DISP & ILLUMI” > “Display
Select” > “Side Select”
“Display
Dimmer”
Reduces the display Illumination brightness.
“Auto”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“Manual1”: Dims the illumination constantly.
“Manual2”: Dims the illumination darker than
Manual1.
“OFF”: Does not dim the illumination.
Adjusting the display contrast.
“1” - “5” - “12”
Text scroll
Press the [DISP] button for at least 1 second.
The displayed text scrolls.
“Contrast”
“DISP N/P”
Switches the panel display between positive
or negative.
“POSI1”/ “POSI2”/ “NEGA1”/ “NEGA2”
“TEXT Scroll” Specifies whether the text is scrolled
automatically.
“Auto”/ “Manual”
“ILLUMI
Dimmer”
Reduces the key Illumination brightness.
“Auto”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“Manual1”: Dims the illumination constantly.
“Manual2”: Dims the illumination darker than
Manual1.
“OFF”: Does not dim the illumination.
|
28 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
“ILLUMI Effect” Sets whether the key illumination brightness is
changed in conjunction with the key operation.
“OFF”/ “ON”
“ILLUMI MSC Sets whether the key illumination color is
SYNC”
changed in conjunction with the sound volume.
(KDC-X994 only)
“OFF”/ “ON”
(
: Factory setting)
5
6
Make a setting
• When the “
” icon is displayed (at the
PUSH
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
• When the “
” icon is not displayed
PUSH
Press the [4] or [¢] button to select a
setting value.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
English
|
29
Display Settings
Text Display Selection
In FM Tuner source
KDC-X994/KDC-X794 : 5-line display mode
Customization of 5-line Display Mode
& 3-line Display Mode & iPod-like
Display Mode
Frequency & Program Service
name (“Frequency/PS”)
Song title* (“Song Title”)
Artist name* (“Artist Name”)
Station name* (“Station Name”)
Radio text plus* (“Radio Text
Plus”)
Radio text (“Radio Text”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
You can customize the display of the 5-line display
mode, 3-line display mode, and iPod-like display
mode.
1
Select the source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
* Information of Radio text plus is displayed.
KDC-X994/KDC-X794 : 3-line display mode
Frequency & Program Service
name (“Frequency/PS”)
Song title & Artist name*
(“Title/Artist”)
Station name* (“Station Name”)
Radio text plus* (“Radio Text
Plus”)
Radio text (“Radio Text”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
2
3
Enter Menu List mode
Press the [MENU] button.
Enter Display Setting mode and Select the
5-line display mode, 3-line display mode or
iPod-like display mode.
Turn the [VOL] knob and press it when the
* Information of Radio text plus is displayed.
desired item is displayed.
Select “Settings” > “DISP & ILLUMI” > “Display
Select” > “Type Select” > 5-line display mode
or 3-line display mode or iPod-like display
mode.
KDC-BT945U/KDC-MP745U
Frequency (“Frequency)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
In AM Tuner source
Frequency (“Frequency”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Display
Setting
“Display Select”
“Type Select” Selects from 5-line display mode, 3-line display
mode, or iPod-like display mode.
“Side Select” Sets the source display.
Text/ Icon/ Disappear
“Text Select” Sets the text display.
1. Turn the [VOL] knob to select the text
display part
In USB/ iPod/ Audio file source
5-line display mode
Song title (“Song Title”)
Album name (“Album Name”)
Artist name (“Artist name”)
Folder name (“Folder name”)
File name (“File name”)
Play time (“P-Time”)
Play time bar (“Time Bar”) : iPod
only
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
The selected text display part blinks.
2. Press the [4] or [¢] button to
select the text
Blank (“Blank”)
“Status”
Sets the Status display of the 5-line display mode.
Appear/ Disappear
3-line display mode
Ttitle & Artist (“Artist/Ttitle”)
Album & Artist (“Artist/Album”)
Folder name (“Folder name”)
File name (“File name”)
Play time bar (“Time Bar”) : iPod
only
(
: Factory setting)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
5
6
Make a setting
Press the [4] or [¢] button.
Play time (“P-Time”)
Exit Menu List mode
Blank (“Blank”)
Press the [MENU] button for at least 1 second,
and then press it again briefly.
iPod-like display mode
Song title (“Song Title”)
Album name (“Album Name”)
Artist name (“Artist name”)
Blank (“Blank”)
|
30 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
In Music CD source
In SIRIUS/ SAT/ XM source (Optional)
5-line display mode
Disc title (“Disc title”)
Track title (“Track title”)
Play time (“P-Time”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Channel Name (“Channel Name”/ Category Name (“Category Name”
“CHANNEL NAME”)
/“CATEGORY”)
Blank (“Blank”)
Song Title (“Song Title”/“SONG
TITLE”)
Artist name (“Artist name”/
“ARTIST NAME”)
Channel Number (“Channel
Number”/“CHANNEL NUMBER”)
Spectrum analyzer & Clock
(“Speana/Clock”)
In Auxiliary input source
Source name (“Source Name”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Composer name (“Composer
name”) : SIRIUS/SAT only
Date (“Date”)
Blank (“Blank”)
In Standby
3-line display mode
Source name (“Source Name”)
Date (“Date”)
Clock (“Clock”)
Blank (“Blank”)
Channel Name (“Channel Name”/ Channel Number (“Channel
“CHANNEL NAME”)
Artist name & Song Title (“Artist
Number”/“CHANNEL NUMBER”)
Spectrum analyzer & Clock
In Bluetooth audio source (KDC-X994 /KDC-BT945U
only)
name/Song Title”/“NAME/TITEL”) (“Speana/Clock”)
Category Name (“Category Name” Date (“Date”)
5-line display mode
/“CATEGORY”)
Blank (“Blank”)
Bluetooth audio (“Source Name”) Spectrum analyzer & Clock
⁄
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Song title (“Song Title”)
Artist name (“Artist name”)
Album name (“Album Name”)
• If the selected display item does not have any information,
alternative information is displayed.
• Some items cannot be selected depending on the display
type and row.
• When selecting “Folder name”while playing with iPod,
names will be displayed depending on currently selected
browsing items.
• If the iPod Control by Hand Mode is set to on while playing
the iPod, “iPod by Hand Mode” is displayed.
• If all characters cannot be displayed while playing with iPod,
the file number in the list is displayed.
3-line display mode
Bluetooth audio (“Source Name”) Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Ttitle & Artist (“Artist/Ttitle”)
Album & Artist (“Artist/Album”)
Blank (“Blank”)
In Disc changer source (Optional)
Disc title (“Disc title”)
Track title (“Track title”)
Play time (“P-Time”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Information
Music title
Folder name
File name
Display
“TITLE***”
“FLD***”
“FILE***”
Blank (“Blank”)
In HD Radio source (Optional)
5-line display mode
Frequency (“Frequency”)
Station name (“Station Name”)
Song Title (“Song Title”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Album name (“Album Name”)
Artist name (“Artist Name”)
3-line display mode
Frequency (“Frequency”)
Station name (“Station Name”)
Artist name & Song Title (“Artist
name/Song Title”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Artist name & Album name
(“Artist name/Album name”)
English
|
31
Display Settings
Function of KDC-X994
Customization of Spectrum Analyzer
Display Mode
Illumination Color Selection
Selecting the Illumination Color of the panel.
You can customize the display of the Spectrum
analyzer display mode.
1
Enter Menu List mode
Press the [MENU] button.
1
Select the source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
2
Enter Illumination color selection mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “DISP & ILLUMI” > “Color
Select”.
2
3
Enter Menu List mode
Press the [MENU] button.
3
4
Select the place where you want to set the
Illumination Color
Turn the [VOL] knob and press it when the
Enter the Display Setting mode and select the
Spectrum analyzer display mode
Turn the [VOL] knob and press it when the
desired item is displayed.
desired item is displayed.
Place
Display and key
Display
Display
“All”
“Display”
“Key”
Select “Settings” > “DISP & ILLUMI” > “Display
Select” > “Type Select” > Spectrum analyzer
display mode.
Key
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the Illumination Color
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the color from “Variable Scan”/ “Color1”—
“Color 10”/ “User”.
Display
“Display Select”
Setting
“Type Select” Selects the Spectrum analyzer display mode.
Creating “User” color
“Graphic
Select”
Changes the display of the Spectrum analyzer
display mode.
You can create your original color during the
selection from “Color1”— “Color10.”
The color you created can be called when you
select “User”.
“Text Select” Sets the text display.
5
6
Make a setting
1. Press the [VOL] knob for at least 1 second.
Enter the detail color adjustment mode.
2. Set the color.
Press the [4] or [¢] button.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Operation type
Operation
To select the color to adjust. Press the [4] or [¢] button.
(red, green, or blue)
To adjust color.
(Range: 0 – 9)
Turn the [VOL] knob.
3. Press the [VOL] knob.
Exit the detail color adjustment mode.
5
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
|
32 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Auxiliary Input Display Setting
Selecting the display when changing to Auxiliary
input source.
1
Select the AUX source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select the “AUX” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
2
3
Enter Menu List mode
Press the [MENU] button.
Enter Auxiliary input display setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “AUX Name Set”.
4
5
Select the Auxiliary input display
Turn the [VOL] knob.
Select “AUX”, “DVD”, “PORTABLE”, “GAME”, “VIDEO”, or
“TV”
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
• The Auxiliary input display can be set only when the
built-in auxiliary input or the auxiliary input of optional
KCA-S220A is used. On the KCA-S220A, “AUX EXT”is
displayed by default.
• AUX source is initially set to “OFF”. Before display setting,
set “Built in AUX” described in <Initial Settings> (page 34)
to “ON”.
English
|
33
Clock and Other Functions
2. Press the [¢] button.
Release MENU VOL
3. Turn the [VOL] knob to adjust the month.
4. Press the [¢] button.
5. Turn the [VOL] knob to adjust the day.
6. Press the [VOL] knob.
7
8
9
Enter Date format mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Date Mode Select”.
SRC 4
¢
Clock and Date Adjustment
Select Date format
Turn the [VOL] knob and press it when the
desired item is displayed.
Select from 7 types.
You can adjust the clock and date.
Display
“Settings”
“Clock & Date”
“Clock Adjust”
Overview
Exit Menu List mode
Press the [MENU] button for at least 1 second,
Sets the clock.
and then press it again briefly.
“Time Synchronized” Synchronizing the RDS station time
data and this unit’s clock. (KDC-X994/
KDC-X794 only)
Initial Settings
“OFF”/ “ON”
“Date Adjust”
Sets the date.
You can select following Initial Setting items.
“Date Mode Select” Sets the date display mode.
1
Select the Standby
1
2
Enter Menu List mode
Press the [MENU] button.
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select the “STANDBY” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
Select RDS’s automatic time adjustment
(KDC-X994/ KDC-X794 only)
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Clock & Date” > “Time
Synchronize” > “ON” or “OFF”.
When selected “OFF”, proceed to step 3.
When selected “ON”, proceed to step 5.
2
3
Enter Menu List mode
Press the [MENU] button.
Enter Initial Setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Initial Settings”.
3
4
Enter Clock adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Clock & Date” > “Clock
Adjust”.
4
Select the setting item to adjust
Turn the [VOL] knob.
Display
Overview
“Initial Settings”
“SRC Select”
Adjusting Clock
1. Turn the [VOL] knob to set the hours.
2. Press the [¢] button.
3. Turn the [VOL] knob to set the minutes.
4. Press the [VOL] knob.
Sets the source selection method.
“Settings 1”/ “2”
Setting the operation check sound (beep sound)
ON/OFF.
“Beep”
“OFF”/ “ON”
“Menu Language” You can select the display language for the
Menu list item.
5
6
Enter Date adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
“English”/ “Français”/ “Español”
Select “Date Adjust”.
Adjusting Date
1. Turn the [VOL] knob to adjust the year.
|
34 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
“Built in AUX”
When this is set to ON, AUX source can be
selected.
“ON”: Allows AUX source to be selected. Use
this setting when the built-in AUX terminal
is connected to the external equipment all
the time.
Demonstration mode Setting
Turning the demonstration mode ON/OFF.
1
Enter Menu List mode
Press the [MENU] button.
“OFF”: Disable AUX source selection. Use this
setting when the built-in AUX terminal is
not used.
2
Enter Demonstration mode setting
Turn the [VOL] knob and press it when the
desired item is displayed.
“Forced CD-DA” Sets the method for reading CD.
“Settings 1”: Automatically distinguishes
between audio file disc and music CD when
playing disc.
“Settings 2”: Forces playing as music CD.
“Favorite Delete” Deletes Favorite Preset Memory.
Refer to <Favorite Preset Memory Delete>
Select “DEMO Mode”.
3
4
Set the Demonstration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “ON” or “OFF”.
Exit Menu List mode
Press the [MENU] button.
“Built in AMP”
Selecting“OFF”turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
“OFF”/ “ON”
DSI (Disabled System Indicator) of the unit blinks
when the faceplate is removed.
“OFF”/ “ON”
Function of KDC-X794/ KDC-MP745U
Muting volume upon reception of
Phone call
“DSI”
(
: Factory setting)
The audio system automatically mutes when a call
comes in.
5
6
Make a setting
• When the “
” icon is displayed (at the
PUSH
When a call comes in
“CALL” is displayed.
The audio system pauses.
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
Listening to the audio during a call
Press the [SRC] button.
The “CALL” display disappears and the audio system
• When the “
” icon is not displayed
PUSH
Press the [4] or [¢] button to select a
setting value.
comes back ON.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
When the call ends
Hang up the phone.
The “CALL” display disappears and the audio system
comes back ON.
⁄
• To use the TEL Mute feature, you need to hook up the MUTE
wire to your telephone using a commercial telephone
70).
English
|
35
Clock and Other Functions
Theft Deterrent Faceplate
The faceplate of the unit can be detached and
taken with you, helping to deter theft.
Removing the Faceplate
1
Press the Release button.
Drop open the faceplate.
2
Drawing the faceplate to left side pull it to
forward and remove it.
¤
• The faceplate is a precision piece of equipment and can
be damaged by shocks or jolts.
• Keep the faceplate in its faceplate case while detached.
• Do not expose the faceplate (and the faceplate case) to
direct sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
Reattaching the Faceplate
3
Align the shaft on the unit with the depression
on the faceplate.
4
Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to
use the unit.
|
36 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
English
|
37
Audio Adjustments
“2Zone”
“2Zone Select”
Sets the Dual Zone System.
SRC MENU VOL
“Preset”
Sets the audio preset.
(
: Factory setting)
1
Select the source
4
¢
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
Audio Control
You can adjust following Audio Setting items.
Display
“SubWoofer Level”
Overview
You can set subwoofer level.
“–15” — “0” — “+15”
“Bypass”: Disables the DSP function.
“Through”: Enables the DSP function.
Sets the sound quality.
2
3
Enter Audio Control mode
Press the [VOL] knob.
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
“DSP Set”
“Equalizer”
Sets the Bass Boost level in two steps.
“OFF”/ “Step1” – “2”
Compensates the low volume or bass sound
being lost by road noises to make vocal sound
clearer.
4
5
Make a setting
Press the [4] or [¢] button to select a
setting value, and then press the [VOL] knob.
“Bass Boost”
“HIGHWAY-SOUND”
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
“OFF”/ “Step1”/ “2”/ “3”
“Supreme+”
“Position”
Turns ON/OFF the Supreme plus function.
Can be set while Music CD source, Audio file
source of USB and iPod source.
“ON”/ “OFF”
Compensates the sound environment in
accordance with the listening position.
40).
Adjusts left/right speaker balance.
(Left) “L15” — “0” — “R15” (Right)
Adjusts front/rear speaker balance.
(Rear) “R1”5 — “0” — “F15” (Front)
Remarks
• DSP Set
When “DSP Set” is set to “BYPASS”, the DSP function is
disabled , and the colored items can not be set.
• HIGHWAY-SOUND
Increases the volume of faintest sound being lost by road
noises to make the sound more audible. Additionally, it
accentuates bass sound being lost by road noises to make
the bass sound more dynamic.
“Balance”
“Fader”
• Supreme+ (Supreme Plus)
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range that is cut
off when encoding. The bass and vocal sound that are cut
off by encoding are supplemented for the reproduction
of natural sound quality. Supplementing is optimized by
compression format (AAC, MP3 or WMA) and processed
according to bit rate. The effect is negligible with music
that is encoded at high bit rate, variable bit rate or has
minimal high frequency range.
“SubWoofer”
Turns on/off the subwoofer output.
“ON”/ “OFF”
“Detailed Setup”
“Car Type”
“Speaker”
“Car Type Adjust”
“X'Over”
To get clear sound, set the sound environment
according to the location and size of physically
installed speakers with reference to the
followings:
Sets each source’s volume as a difference from
the basic volume.
The bass and vocal sound of Music CD/ iPod is also
supplemented.
• Dual Zone System
Main source and sub source (Auxiliary input) output Front
channel and Rear channel separately.
“Volume offset”
“–8” — “ 0” (AUX: “-8”— “+8”)
|
38 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Preset Equalizer curve Select
Manual Equalizer Control
You can adjust following Equalizer Control items.
KDC-X994/ KDC-X794
You can select following Equalizer curve.
Display
“Natural”
“User”
Equalizer curve
Natural
User*
Band
Item
Range
“BAND1”(62.5 Hz) “GAIN”Band level
“EFCT”Bass Effect
“BAND2”(250 Hz) “GAIN”Band level
-9 –+9 dB
“ON”/“OFF”
-9 –+9 dB
-9 –+9 dB
-9 –+9 dB
-9 –+9 dB
: Factory setting)
“Rock”
“Pops”
“Easy”
Rock
Pops
Easy
“BAND3”(1 kHz)
“BAND4”(4 kHz)
“GAIN”Band level
“GAIN”Band level
“Top 40”
“Jazz”
Top 40
Jazz
“BAND5”(16 kHz) “GAIN”Band level
“Game”
“iPod”
Game
(
iPod (During iPod source only)
KDC-BT945U/ KDC-MP745U
* The Equalizer curve set in the section <Manual Equalizer
Control> is recalled.
Band
“BAND1”(60/ 100/ “GAIN”Band level
160/ 250/ 400 Hz)
Item
Range
-9 –+9 dB
0.25/ 0.5/ 1.0/
2.0
(
: Factory setting)
“Q”Quality
1
Select the source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
“BAND2”(630/ 1k/ “GAIN”Band level
-9 –+9 dB
0.25/ 0.5/ 1.0/
2.0
1.6k/ 2.5k Hz)
“Q”Quality
“BAND3”(4k/ 6.3k/ “GAIN”Band level
-9 –+9 dB
0.25/ 0.5/ 1.0/
2.0
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
10k/ 16k kHz)
“Q”Quality
2
3
Enter Audio Control mode
Press the [VOL] knob.
(
: Factory setting)
1
Select the source
Enter Preset Equalizer mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Equalizer” > “Preset Equalizer”.
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
4
Select the Equalizer curve
Press the [4] or [¢] button.
✍ Select the iPod Equalizer curve
You can select from 22 Equalizer curve types for
iPod when “iPod” is selected.
1. Enter iPod Equalizer mode
Press the [VOL] knob.
2. Select the iPod Equalizer curve
Press the [4] or [¢] button and press it
when the desired item is displayed.
2
3
Enter Audio Control mode
Press the [VOL] knob.
Enter Manual Equalizer Control mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Equalizer” > “Manual Equalizer”.
4
5
Select the item you want to set
Operation type
Selects the item.
Adjust each item.
Set the value
Operation
Turn the [VOL] knob.
Press the [
Press the [VOL] button.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
4] or [¢] button.
⁄
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
• You can select for each source.
and then press it again briefly.
⁄
curve Select> (page 39), Manual Equalizer Control is
disabled.
• You can select for each source.
English
|
39
Audio Adjustments
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired value is displayed.
Listening Position Selection
The sound environment can be compensated in
accordance with the selected position. According to
the listening position, select the position from the
following settings.
Item
Setting overview
Front Left speaker
Front Right speaker
Rear Left speaker
Rear Right speaker
“FRONT”/“L”
“FRONT”/“R”
“REAR”/“L”
“REAR /“R”
Compensation seat
Not compensating.
Front-Left seat
Front-Right seat
Front seat
Display
“ALL”
“Front-Left”
“Front-Right”
“Front”
“SUBWOOFER”/“L” Subwoofer Left
“SUBWOOFER”/“R” Subwoofer Right
“INITIAL”
Initialize the setting values.
(
: Factory setting)
5
6
Set the value
1
Select the source
Press the [4] or [¢] button.
Adjust between 0 and 5.58 feet.
Press the [VOL] knob for at least 1 second if you
want to execute the “INITIAL”.
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
2
3
Enter Audio Control mode
Press the [VOL] knob.
Enter Preset position setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Dual Zone System
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
Select “Position” > “Preset Position”.
4
5
Select the seat you want to compensate
Press the [4] or [¢] button.
Display
Overview
“2Zone Rear Volume”*1 Adjust the volume of Rear channel.
“0” — “35”
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
“Detailed Setup”
“2Zone”
Sets the Dual Zone System.
“OFF”/ “ON”
Specifies the destination of sub source sound
when the Dual Zone function is turned on.
“Rear”/ “Front”
“2Zone Select”*1
Function of KDC-X994/ KDC-X794
Listening Position Fine Adjustments
*1 The Dual Zone System is set to “ON”.
Making fine adjustment of the value specified at
Preset position selection per speaker.
(
: Factory setting)
1
Select the source
1
Select the source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
2
3
Enter Audio Control mode
Press the [VOL] knob.
2
3
Enter Audio Control mode
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup”.
Enter Manual position setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
4
Select the item you want to set
Turn the [VOL] knob and press it when the
Select “Position” > “DTA”.
|
40 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
desired item is displayed.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
• Select Main source by [SRC] button.
• Adjust the volume of Front channel by [VOL] knob.
• The Audio Control has no effect on sub source.
• There are following limitations when Dual Zone System
is enabled.
- There is no output from the subwoofer.
and DSP function are not available.
• The Bluetooth audio source can be set exclusively to the
front speaker. Set “2Zone Select” to “Rear”.
English
|
41
DSP Setup
Speaker Setting
SRC MENU VOL
The speaker X’Over is automatically set when the
position and size of each speaker are selected from
the following items.
Speaker
Item
Range
“FRONT”
“SIZE”
Speaker Size Front
KDC-X994/ KDC-X794:
4
¢
“O.E.M.”, “4inch”, “5inch”, “6 1/2inch”,
“6 3/4inch”, “7inch”, “4x6”, “5x7”, “6x8”,
“6x9”, “7x10”
Car Type Selection
KDC-BT945U/ KDC-MP745U:
“Small”, “Medium”, “Large”
You can compensate the delay of the sound arrival
time by selecting your environment from the
following car types.
“LOCATION” Speaker Location Front
“Door”, “On Dash”, “Under Dash”
“TWEETER” Speaker Size Tweeter
Display
“OFF”
Overview
Not compensating.
Compact car
Full size car
Station wagon
Minivan
“None”, “Use”
“REAR”
“SIZE”
Speaker Size Rear
KDC-X994/ KDC-X794:
“Compact”
“Full size car”
“Wagon”
“Minivan”
“SUV”
“None”, “O.E.M.”, “4inch”, “5inch”,
“6 1/2inch”, “6 3/4inch”, “7inch”, “4x6”,
“5x7”, “6x8”, “6x9”, “7x10”
KDC-BT945U/ KDC-MP745U:
“None”, “Small”, “Medium”, “Large”
Sport-utility vehicle
Long Minivan
“Minivan (Long)”
“LOCATION” Speaker Location Rear
(
: Factory setting)
• “Door”, “Rear Deck”
1
Select the source
• “2nd Row”, “3rd Row” (Car Type:
“Minivan”, “Minivan (Long)”)
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
“SUB W”
“SIZE”
Speaker Size Subwoofer
KDC-X994/ KDC-X794:
“None”, “6 1/2inch”, “8inch”, “10inch”,
“12inch”, “15inch Over”
KDC-BT945U/ KDC-MP745U:
“None”, “Small”, “Large”
2
3
Enter Audio Control mode
Press the [VOL] knob.
(
: Factory setting)
1
Select the source
Enter Cabin select mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup” > “Car Type”.
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
4
5
6
Select the car type
Press the [4] or [¢] button.
2
3
Enter Audio Control mode
Press the [VOL] knob.
Set the value
Press the [VOL] button.
Enter Speaker setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup” > “Speaker”.
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
4
Select the item you want to set
• You can compensate the distances in more details by
Operation type
Selects the item.
Adjust each item.
Set the value
Operation
Turn the [VOL] knob.
Press the [
Press the [VOL] button.
4] or [¢] button.
|
42 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
Reference point
and then press it again briefly.
+3.2 feet
Car Type Fine Adjustments
FRONT
FRONT
REAR
1.7 feet
Adjusting fine tuning of the speaker position
compensation value specified at <Car Type
2.6 feet
REAR
Display
“Front”
“Rear”
“SW”
Item
Range
4.9 feet
Front speaker
Rear speaker
Subwoofer
0 – 14.44 feet
0 – 14.44 feet
0 – 14.44 feet
+2.3 feet
+0 feet
SUB-W
(
: Factory setting)
1
Select the source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
2
3
Enter Audio Control mode
Press the [VOL] knob.
Enter Car Type Adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup” > “Car Type Adjust”.
4
Select the item you want to set
Operation type
Selects the item.
Adjust each item.
Set the value
Operation
Turn the [VOL] knob.
Press the [
Press the [VOL] button.
4] or [¢] button.
The settings of the delay time are automatically
identified and compensated by specifying the
distances of each speaker from the center of the
vehicle interior.
1 Set the front and rear positions and the height
of the reference point to the position of the ears
of the person sitting in the front seat, and set
the right and left positions to the center of the
vehicle interior.
2 Measure the distances from the reference point
to the speakers.
3 Calculate the distance difference in accordance
with the farthest speaker.
English
|
43
DSP Setup
6
7
Repeat steps 3 to 4 to complete the X’Over
settings.
X’Over Setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Display
Item
Range
“X’Over”
“Front”
“FC”
Front High Pass Filter
Audio Preset Memory
Through, 30*, 40, 50*, 60, 70, 80,
90*, 100, 120, 150, 180, 220, 250*
(Hz)
Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
“SLOPE” Front High Pass Slope
-6, -12, -18, -24 dB/Oct
Rear High Pass Filter
Through, 30*, 40, 50*, 60, 70, 80,
90*, 100, 120, 150, 180, 220, 250*
(Hz)
Sound Control.
“Rear”
“FC”
“SLOPE” Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
“SubWoofer” “FC”
Subwoofer Low Pass Filter
30*, 40, 50*, 60, 70, 80, 90*, 100,
120, 150, 180, 220, 250*, Through
(Hz)
2
Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
“SLOPE” Subwoofer Slope
-6, -12, -18, -24 dB/Oct
“PHASE” Subwoofer Phase
Reverse (180°)/ Normal (0°)
Select “Detailed Setup” > “Preset” > “Memory”.
3
4
Select the number to put in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
(
: Factory setting)
* Function of KDC-X994/ KDC-X794
1
Select the source
Select a preset number.
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Memory Completed” is displayed.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
2
3
Enter Audio Control mode
Press the [VOL] knob.
Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup” > “X’Over”.
⁄
• Register 6 patterns of Audio Preset Memory.
• Preset number “1”:
When you press the Reset, all the sources will be the
setting value which is registered.
• Preset number “1”and “2”:
The memory cannot be erased by the Reset button.
• This function cannot be registered when the iPod
4
5
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Front”, “Rear”, or “SubWoofer”.
Select the item you want to set
Operation type
Selects the item.
Adjust each item.
Set the value
Operation
Turn the [VOL] knob.
Press the [
Press the [VOL] button.
4] or [¢] button.
|
44 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Audio Preset Recall
Recalling the sound setup registered by <Audio
1
Select the source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
2
Enter Audio preset recall mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup” > “Preset” > “Recall”.
3
4
Select the number to recall in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select preset number.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Recall Completed” is displayed.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
changed to the value which was recalled.
• The Equalizer curve is changed to the value which was
recalled by the selected source.
English
|
45
Favorite Control
• If the contents in iPod are changed after the FAVORITE
registration, the list registered in this unit becomes
different from that in iPod. In this case, perform the
FAVORITE registration again.
MENU VOL
Favorite Preset Recall
Retrieving an item registered to Favorite.
FAV
1
Enter Favorite Preset Recall mode
Press the [FAV] button.
Favorite Preset Memory
2
Select the number to recall in the Favorite
memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select preset number.
Registering the operation procedure to select your
favorite broadcast station or iPod Playlists/ Artists,
etc.
1
Display a favorite item
Source
Registerable items
Cancelling the Favorite Preset Recall mode
TUNER/SIRIUS/XM/HD Frequency or channel
Press the [FAV] button.
iPod
Search item such as Playlists/ Artists/
Albums, etc.
⁄
Menu list Setting
Audio control
Hands-free phone
Menu list Setting item
Audio control item
Telephone number retrieval.
• When iPod is selected for the source, the list selection
screen for Playlists/ Artists/ Albums, etc. is displayed.
Songs will not be automatically played.
“
” is displayed when the operation procedure
FAV
can be registered.
iPod setting
The desired list in the first hierarchy can be
Favorite Preset Memory Delete
Deleting an item registered to Favorite.
registered.
1
Select the Standby
1st hierarchy
2nd hierarchy
3rd hierarchy
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select the “STANDBY” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
iPod
PLAYLISTS
ALL ARTISTS
ARTISTS 1
ARTISTS 2
ARTISTS 3
ARTISTS
ALBUMS
ALL ALBUMS
ALBUM 1
ALBUM 2
2
3
Enter Menu List mode
Press the [MENU] button.
COMPOSERS
AUDIOBOOKS
ALBUM 3
Enter Favorite Preset Memory Delete mode
Turn the [VOL] knob and press it when the
desired item is displayed.
2
3
4
Enter Favorite Preset Memory mode
Press the [FAV] button for at least 1 second.
Select “Initial Settings” > “Favorite Delete”.
Select the number to put in the memory
4
5
Enter Favorite Preset Memory Delete mode
Press the [VOL] knob.
Turn the [VOL] knob.
Put the Favorite Preset in the memory
Select the number you want to delete
Turn the [VOL] knob and press it when the
desired item is displayed.
Press the [VOL] knob.
Cancelling the Favorite Preset Memory mode
Press the [FAV] button.
Select preset number.
⁄
“Delete?” is displayed.
Select “ALL” if you want to delete all.
• Registering the operation procedure to an existing
preset number overwrites the existing procedure.
• Register 6 of Favorite Preset Memory.
6
Turn the [VOL] knob and press it when the
desired item is displayed.
The memory cannot be erased by the Reset button.
|
46 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Select “YES”.
“Completed” is displayed.
Exit Favorite Preset Memory Delete mode.
English
|
47
Function of KDC-X994/ KDC-BT945U
KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory)
Bluetooth Setup
“PIN Code Edit” Specify the PIN code required when registering
this unit using the Bluetooth device.
MENU VOL
“Auto Answer” Answer a call automatically after lapse of the
preset time interval for automatic answer.
“OFF”/ “0s” – “8s” – “99s”
“Bluetooth HF/ You can specify output speakers for hands-free
Audio”
voice communication and Bluetooth audio
sound.
“FRONT”: Outputs voice from the front
speakers.
“ALL”: Outputs voice from the front and rear
speakers.
You can output a beep from the speaker when
a call comes in.
“ON”: Beep is heard.
“OFF”: Beep is canceled.
4
38
¢
/PLAY MODE
Bluetooth Setting
You can select following Bluetooth Setting items.
“Call Beep”
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
“BT F/W Update” Display the version of the firmware of this unit.
“Mic Gain”*1
Adjust the sensitivity of the microphone for a
telephone call. Adjust the voice of caller. Setting
to“+”increases the voice volume.
“–3” – “0” – “+3”
Reduce the noises generated by surrounding
environment without changing the microphone
volume. Adjust the voice of caller when it is
not clear. Setting to“+”increases the noise
reduction.
✍ You can also select from “Settings” in Menu List
mode.
“NR Level”*1
2
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings”.
“–3” – “0” – “+3”
Select the Menu item
Turn the [VOL] knob and press it when the
desired item is displayed.
“Echo Cancel
LV“*1
Adjust the level of echo cancellation. Setting to
“+”increases the echo cancel reduction.
“–2” – “0” – “+2”
Display
“BT Settings”
Overview
(
: Factory setting)
*1 Function of KDC-X994/ KDC-BT945U
“Phone Selection” Select a cell-phone or Bluetooth audio player
4
5
Make a setting
connection.
“Audio Selection”
• When the “
” icon is displayed (at the
PUSH
Refer to <Selecting the Bluetooth device You
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
“SMS Download” Download a short message.
Display the received short message.
“SMS Inbox”
“Voice Tag”
• When the “
” icon is not displayed
PUSH
Refer to <SMS (Short Message Service)>
Registers voice for voice recognition and voice
to select the Phone number category in Phone
book.
Press the [4] or [¢] button to select a
setting value.
Exit BT Settings mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
“Detailed Setup” Move to detailed item.
“Device Regist.” Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth device>
“SPCL DVC
Select”
Remarks
• “Auto Answer” (Setting the Time Interval for Automatic
Answer)
This function automatically answers (responds to) a call
after lapse of the preset time interval for automatic answer.
“OFF” : Does not answer the phone call automatically.
“0”: Automatically answers the phone call at once.
“Device Delete” Cancel registration of the Bluetooth device.
Refer to <Deleting a Registered Bluetooth
|
48 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
“1s”– “99s”: Automatically answers the phone call after
lapse of 1 – 99 seconds.
6
Transmit the PIN code
Press the [VOL] knob for at least 1 second.
If “Pairing Success” is displayed, registration is
completed.
✍ If the error message appears even though the
PIN code is correct, try <Registering Special
⁄
• If the time set in the cell-phone is shorter than that set in
the unit, the former will be used.
• This function does not work for call waiting.
• “Bluetooth HF/Audio” (Setting up the Voice Output
Speakers)
Select the speaker which is further from the microphone in
7
8
Return to the device list
Press the [MENU] button.
order to prevent howling or echoes.
• “BT F/W Update” (Displaying the Firmware Version)
Display the version of the firmware of this unit.
For how to update the firmware, access our web site.
Exit BT Settings mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
Registering Bluetooth device
⁄
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to 5 Bluetooth devices to this unit.
• This unit allows up to eight digits to be input for a PIN
code. If a PIN code cannot be input from this unit, it can
be input from the Bluetooth device.
• If there are 5 or more Bluetooth devices registered, you
cannot register a new Bluetooth device.
Registering from this unit
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Registering Special Bluetooth device
Allow registration of a special device that cannot be
registered normally (pairing).
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
✍ You can also select from “Settings” in Menu List
mode.
1. Select Special device registration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings” > “Detailed Setup” > “SPCL
DVC Select”.
2. Enter Special device registration mode
Press the [VOL] knob for at least 1 second.
A list is displayed.
2
Enter Bluetooth device registration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings” > “Detailed Setup” >
“Device Regist.”.
Search for the Bluetooth device.
3. Select a device name
Turn the [VOL] knob and push the center when
the desired device name is displayed.
If “Completed” is displayed, registration is
completed.
4. Go through the procedure step 3 of
<Registering from this unit> and complete
the registration (pairing).
When search is completed, “Finished” is displayed.
3
4
Select a Bluetooth device
Turn the [VOL] knob and press it when the
desired item is displayed.
“Paring” is displayed (except KCA-BT200)
If “Pairing Success” is displayed, proceed to step 7.
If “PIN Code NG” is displayed, proceed to steps 5
to 6.
Cancelling Special device registration mode
Press the [MENU] button for at least 1 second.
⁄
• If the device name is not in the list, select “Other Phones”.
5
Input the PIN code
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Press the [
Press the [
¢
] button.
] button.
4
English
|
49
Function of KDC-X994/ KDC-BT945U
KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory)
Bluetooth Setup
Registering PIN Code
Selecting the Bluetooth device You
Wish to Connect
By operating the Bluetooth device, specify the PIN
code necessary for registering this unit.
When two or more Bluetooth devices have already
been registered, you need to select the Bluetooth
device you wish to use.
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
✍ You can also select from “Settings” in Menu List
mode.
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
✍ You can also select from “Settings” in Menu List
mode.
2
3
Enter PIN code edit mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings” > “Detailed Setup” > “PIN
Code Edit”.
2
3
Select Bluetooth device selection mode
Turn the [VOL] knob and press it when the
desired item is displayed.
The current setting of PIN code is displayed.
Cell-phone
Select “BT Settings” > “Phone Selection”.
Input the PIN code
Operation type
Operation
Audio player
Select “BT Settings” > “Audio Selection”.
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Press the [
Press the [
¢
] button.
] button.
Enter Bluetooth device selection mode
Press the [VOL] knob for at least 1 second.
“(name)” is displayed.
4
4
5
Register a PIN code
Press the [VOL] knob for at least 1 second.
If “Completed” is displayed, registration is
completed.
4
5
Select the Bluetooth device
Turn the [VOL] knob.
Set up the Bluetooth device
Press the [4] or [¢] button.
“✱(name)” or “-(name)” is displayed.
“✱”: The selected Bluetooth device is busy.
“-”: The selected Bluetooth device is on standby.
“ “ (blank): The Bluetooth device is deselected.
Exit BT Settings mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
6
Exit BT Settings mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
⁄
• By default, “0000”is specified.
• A PIN code can be specified with up to eight digits.
⁄
• If a Bluetooth device is already selected, deselect it, and
then select a different one.
• If you cannot select a device using the audio player,
connect the device with the audio player.
|
50 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Deleting a Registered Bluetooth
device
Downloading the Phone Book
Download the phone book data from the cell-
phone to this unit so that you can use the Phone
Book of this unit.
You can delete a registered Bluetooth device.
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
To download automatically
If the cell-phone supports a phone book
synchronization function, the phone book is
downloaded automatically after Bluetooth
connection.
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
✍ You can also select from “Settings” in Menu List
mode.
⁄
• Setting on the cell-phone may be required.
• If no phone book data is found in the unit even after
the compete display, your cell-phone may not support
automatic download of phone book data. In this case, try
downloading manually.
2
3
Enter Bluetooth device deletion mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings” > “Detailed Setup” >
“Device Delete”.
To download from the cell-phone manually
“(name)” is displayed.
1
By operating the cell-phone, end the hands-free
connection.
Select the Bluetooth device
Turn the [VOL] knob.
2
By operating the cell-phone, send the phone
book data to this unit
By operating the cell-phone, download the phone
book data to this unit.
• During downloading:
“Downloading” is displayed.
• After completion of downloading:
“Completed” is displayed.
4
5
Delete the selected Bluetooth device
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Delete” is displayed.
6
Exit BT Settings mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
3
By operating the cell-phone, start the hands-
free connection.
To clear the downloading completion message
Press any button.
⁄
• Up to 1000 phone numbers can be registered for each
registered cell-phone.
⁄
• When a registered cell-phone is deleted, its Phone Book,
• Up to 32 digits can be registered for each phone number
along with up to 50* characters representing a name.
(* 50: Number of alphabetic alphabetical characters.
Fewer characters can be input depending on the type
of characters.)
log, SMS, and voice tag are also deleted.
• To cancel downloading of the phone book data, operate
the cell-phone.
English
|
51
Function of KDC-X994/ KDC-BT945U
KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory)
Bluetooth Setup
Function of KDC-X794/KDC-MP745U
Select “PB Name Check” (Play)
Adding a Voice Dialing Command
5
Press the [VOL] knob.
Play the registered voice and return to step 2.
Add a voice tag to the phone book for voice dialing.
You can register up to 35 voice tags.
Select “PB Name Delete” (Delete)
1
Enter Bluetooth mode
Press the [PLAY MODE] button for at least 1
second.
✍ You can also select from “Settings” in Menu List
mode.
5
6
Delete a voice tag
Press the [VOL] knob.
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
Exit BT Settings mode
Press the [PLAY MODE] button for at least 1
second.
2
Enter Phone book name edit mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings” > “Voice Tag” > “PB Name
Edit”.
⁄
• Audio sound is not output during voice tag registration.
3
4
Search for the name to register
Function of KDC-X794/KDC-MP745U
Setting a Voice Command for
Category
Select the name to register with reference to 4 in
If a voice tag has already been registered for a
name, “*”is displayed before the name.
Add a voice tag to the phone number category
(type) for voice calling.
Select a mode
Turn the [VOL] knob.
1
Enter Bluetooth mode
Press the [PLAY MODE] button for at least 1
Display
Operation
“PB Name Regist”
“PB Name Check”*
“PB Name Delete”*
“Return”
Register a voice tag.
Play a voice tag.
Delete a voice tag.
Return to step 2.
second.
✍ You can also select from “Settings” in Menu List
mode.
2
Enter Phone Number type edit mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings” > “Voice Tag” > “PN Type
Edit”.
* Displayed only when a name for which a voice tag has
been registered is selected.
Select “PB Name Regist” (Regist)
5
Register a voice tag (first)
“Enter Voice 1”is displayed.
When a beep is heard, say a voice tag within 2
seconds.
3
4
Select the category (type) you wish to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “General”, “Home”, “Office”, “Mobile”, or
“Other”
6
Confirm the voice tag (second)
“Enter Voice 2” is displayed.
When a beep is heard, say the same voice tag as
that you said in step 6 within 2 seconds.
“Completed” is displayed.
Select a mode
Turn the [VOL] knob.
Display
Operation
7
End registration
Press the [VOL] knob.
Return to step 2. You can register another voice tag
continuously.
“PN Type Regist”
“PN Type Check”*
“PN Type Delete”*
“Return”
Register a voice tag.
Play a voice tag.
Delete a voice tag.
Return to step 2.
* Displayed only when a name for which a voice tag has
been registered is selected.
⁄
• If your voice cannot be recognized, a message is
displayed. Pressing the [VOL] knob allows you to retry
voice input. (page 52)
5
Register the category (type) by performing
steps 5 to 7 in <Adding a Voice Dialing
|
52 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
6
Exit BT Settings mode
Press the [PLAY MODE] button for at least 1
second.
⁄
• Set the voice tag for all the 5 categories. If the voice tag
is not registered for all the categories, the Phone book
may not be recalled by voice command.
English
|
53
Function of KDC-X994/ KDC-BT945U
KDC-X794/ KDC-MP745U with KCA-BT200 (Optional Accessory)
SMS (Short Message Service)
Downloading the SMS
SMS (Short Message Service)
Download the short message (SMS) arrived at the
cell-phone so that it can be read on this unit.
The SMS arrived at the cell-phone is displayed on
the receiver.
A newly arrived message is displayed.
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
¤
• To prevent car accidents, the driver should not read the
SMS while driving.
When a new message arrives
“SMS Received” is displayed.
The display disappears with any operations.
✍ You can also select from “Settings” in Menu List
mode.
Displaying the SMS
2
3
Enter SMS download mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings” > “SMS Download”.
1
Enter Bluetooth mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
Start downloading
Press the [VOL] knob.
“Downloading” is displayed.
When the downloading finishes, “Completed” is
displayed.
✍ You can also select from “Settings” in Menu List
mode.
2
3
4
Enter SMS Inbox mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings” > “SMS Inbox”.
A message list appears.
4
Exit BT Settings mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
Select a message
Turn the [VOL] knob.
Each pressing of the [DISP] button switches
between telephone number or name and message
reception date.
⁄
• The cell-phone must be able to transmit the SMS using
Bluetooth. Setting on the cell-phone may be required.
If the cell-phone does not support SMS function, the
SMS download item in Function Control mode is not
displayed.
Display the text
Press the [VOL] knob.
• When the SMS is downloaded from the cell-phone, the
unopened messages in the cell-phone are opened.
• The already-read and unread short messages can be
respectively downloaded up to 75.
Turning the [VOL] knob scrolls the message.
Pressing the [VOL] knob again returns to the
message list screen.
5
6
Exit SMS Inbox mode
Press the [MENU] button.
Exit BT Settings mode
KDC-X994 KDC-BT945U
Press the [ ] button.
KDC-X794 KDC-MP745U
Press the [PLAY MODE] button for at least 1
second.
⁄
• The unopened message is displayed at the beginning
of the list. Other messages are displayed in the order of
reception.
• The SMS that has arrived when the cell-phone is not
|
54 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
linked with Bluetooth cannot be displayed. Download
the SMS.
• The short message cannot be displayed during
downloading the SMS.
English
|
55
Satellite Radio Tuner Control (Optional)
Satellite Radio Setting
SRC MENU VOL
You can select following Satellite Radio Setting
items.
1
2
Select Satellite Radio source
Enter Menu List mode
Press the [MENU] button.
4
¢
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”.
Basic Operation
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
Selecting Satellite Radio source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select the “SAT”, “SIRIUS”, or “XM” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
Display
Selectable setting/item
“Settings”
“Seek Mode” Selects the tuning mode of the radio.
“Channel”: Normal manual seeking control.
“Preset”: Search in order of the channels in the
Preset memory
⁄
• You need to register to the service provider to receive
the service by Satellite Radio. Consult the service
provider if “CALL … TO SUBSCRIBE” appears.
• The radio may take a little time to start receiving after
you select the Satellite Radio source.
“ESN”
Displays the Electronic Serial Number of satellite
radio.
“ESN=”
(
: Factory setting)
• If the signal reception fails, “Acquiring Signal”/ “No Signal”
appears.
5
6
Make a setting
Press the [4] or [¢] button.
Selecting the channel
Press the [4] or [¢] button.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Selecting the Preset Band
1. Enter Menu List mode
Press the [MENU] button.
2. Turn the [VOL] knob and press it when the
desired item is displayed.
Select “SR1”, “SR2”, “SR3” or “SR4”. (SIRIUS/
SAT)
Category and Channel Search
Selecting the channel and category you want to
receive.
Select “XM1”, “XM2”, “XM3” or “XM4”. (XM)
1
2
Select Satellite Radio source
Enter Menu List mode
Press the [MENU] button.
3
Enter Category and Channel Search mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Channel Search”.
4
5
Select the Category
Turn the [VOL] knob to select Category, and
then press the [VOL] knob.
Select the Channel
Turn the [VOL] knob to select Channel, and
then press the [VOL] knob.
Cancelling Category and Channel Search mode
|
56 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Press the [MENU] button for at least 1 second,
and then press it again briefly.
3
4
5
Enter Channel Scan
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Channel Scan”.
⁄
• You cannot Channel search until the category
information is acquired.
Start Channel Scan
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
Preset Memory
Putting the channel in the memory.
Release it when the channel you want to listen
to is received
Press the [VOL] knob.
1
2
3
Select the channel you wish to store in the
preset memory
Enter Menu List mode
Press the [MENU] button.
Function of remote control
Direct Access Tuning
Enter Preset Memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Entering the channel and tuning.
1
2
Select Satellite Radio source
Select “List & Memory”.
Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
4
Select the number to put in the memory
Turn the [VOL] knob and press [VOL] knob for
at least 2 seconds when the desired item is
displayed.
“– – – –” is displayed.
3
4
Enter the channel
Press the number buttons.
Select preset number.
Cancelling the Preset Memory mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Tune in to the entered channel
Press the [4] or [¢] button.
⁄
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
• Only the channel number is stored. Category information
is not stored.
⁄
• If you make no button operation for 10 seconds, the
Direct Access Tuning mode is automatically canceled.
• If you cannot receive any signal in the input Channel due
to bad conditions on radio wave or other such problems,
“Acquiring Signal”/ “No Signal” appears.
Preset Tuning
Recalling the channels in the memory.
1
2
Select Satellite Radio source
Enter Menu List mode
Press the [MENU] button.
3
Select a desired station in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “List & Memory” > Preset number.
Channel Scan
Every receivable Channel is checked for 10 seconds.
1
2
Select Satellite Radio source
Enter Menu List mode
Press the [MENU] button.
English
|
57
HD Radio™ Tuner Control (Optional)
Cancelling the Preset Memory mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
SRC MENU VOL
SEARCH MODE
Auto Memory Entry
Putting stations with good reception in the memory
automatically.
4
¢
1
2
3
Select the radio band you wish to store in the
preset memory
Basic Operation
Enter Menu List mode
Press the [MENU] button.
Selecting HD Radio source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select the “HD RADIO” display.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
Enter Auto Memory Entry mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Auto Memory”.
4
Open Auto Memory Entry
Turn the [VOL] knob and press it when the
Selecting the Receiving Band
1. Enter Menu List mode
desired item is displayed.
Press the [MENU] button.
Select “YES”.
When 6 stations that can be received are put in the
2. Turn the [VOL] knob and press it when the
desired item is displayed.
memory, auto memory entry closes.
Select “FM1”, “FM2”, “FM3” or “AM”.
Selecting the Receiving station
Press the [4] or [¢] button.
During reception of stereo stations the “ST”
indicator is light up.
Preset Tuning
Recalling the stations in the memory.
✍ Details of the station selecting in operation are
set in the “Seek Mode” of <HD Radio™ Setting>
1
2
Select the radio band
Enter Menu List mode
Press the [MENU] button.
3
Select a desired station in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Station Preset Memory
Putting a station in the memory.
Select “List & Memory” > Preset number.
1
Select the radio band and tune in a desired
radio station you wish to store in the preset
memory
HD Radio™ Setting
2
3
Enter Menu List mode
Press the [MENU] button.
You can select following HD Radio Setting items.
1
2
Select the HD Radio source
Enter Preset Memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Enter Menu List mode
Press the [MENU] button.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “List & Memory”.
4
Select the number to put in the memory
Turn the [VOL] knob and press [VOL] knob for
at least 2 seconds when the desired item is
displayed.
Select “Settings”.
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
Select preset number.
|
58 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Display
“Settings”
“Seek Mode”
Overview
Desired frequency
92.1 MHz (FM)
810 kHz (AM)
Press button
[9], [2], [1]
[8], [1], [0]
Selects the tuning mode of the radio.
“Auto1”: Automatic search for a station.
“Auto2”: Search in order of the stations in the
Preset memory.
5
Tune in to the entered frequency
Press the [4] or [¢] button.
“Manual”: Normal manual tuning control.
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
“Auto Memory” Memorizes 6 stations with good reception
automatically.
Refer to <Auto Memory Entry> (page 58)
“Receive Mode” Sets the receive mode of the HD Radio receiver.
“Auto”: Automatically tunes to analog broadcast
when there is no digital broadcast.
iTunes Tagging
“Digital”: Digital broadcasts only.
“Analog”: Analog broadcasts only.
Using an iTunes Tagging enabled HD Radio receiver
you can tag your music. When you hear a song you
enjoy on your local HD Radio station, you only have
to press the [SEARCH MODE] button. The song’s
information will then be saved on this unit. The
saved songs will then show up in a playlist called
“Tagged” in iTunes the every next time you sync
your iPod to your computer. So then you just need
to click and then easily buy and download the song
you were tagging directly from the Apple iTunes
Music Store.
“TAG Memory” Displays the tag memory usage of HD Radio
receiver. Up to 50 tags can be registered to
this unit.
“0”/“50”
“Tagging”
Turns ON / OFF the tag memory function of HD
Radio receiver.
“OFF”/“ON”
(
: Factory setting)
5
6
Make a setting
Press the [4] or [¢] button.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
1
Enter iTunes tagging mode
Press the [SEARCH MODE] button.
and then press it again briefly.
“
” will be indicated on the display when song
TAG
information can be registered.
⁄
Function of remote control
58) when using this function.
• Up to 50 TAGs (song’s information) can be registered to
this unit. When iPod is connected, the TAG information
registered to this unit is transferred to the connected
iPod.
Direct Access Tuning
Tuning in a desired radio station by entering the
frequency.
1
2
Select the radio band
• The memory usage can be checked by selecting “TAG
Enter Direct Access Tuning mode
Press the [DIRECT] button.
“– – – –” is displayed.
3
4
Select Tuning item
Press the [DIRECT] button.
Pressing the [DIRECT] button each time switches
the following tuning items as follows.
Items
Frequency
Channel
Cancelling Direct Access Tuning
Display
“– – – –”
“HD –”
—
Enter the frequency or Channel
Press the number buttons.
Example of frequency input:
English
|
59
Basic Operations of remote control
In Tuner/HD Radio source
• Band select: [FM]/[AM]
• Station select: [4]/[¢]
• Recall preset stations: [1] — [6]
VOL
SRC
ATT
ENT
In USB/Music CD/Audio file source
5/∞
• Music select: [4]/[¢]
• Folder select: [FM]/[AM]
• Pause/Play: [ENT]
EXIT
AM
AUD
FM
• Enter Menu List mode: [5]/[∞]
• Movement between folders/files during Search
mode: [5]/[∞]
0 — 9
• Return to previous folder: [
]
DIRECT
In iPod source
• Enter Menu List mode: [5]/[∞]
• Movement between items during Music search
mode: [5]/[∞]
General control
• Return to previous item: [
]
• Music select: [4]/[¢]
• Volume control: [VOL]
• Source select: [SRC]
• Volume reduce: [ATT]
In Satellite Radio tuner source
When the button is pressed again, the volume
• Preset band select: [FM]
returns to the previous level.
• Channel select: [4]/[¢]
• Recall preset channels: [1] — [6]
• Return to previous item: [
• Exit from mode: [EXIT]
• Selection of item: [5]/[∞]
• Determination: [ENT]
]
• Enter Audio Control mode: [AUD]
|
60 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Hands-free phone control
Preparing the remote control unit
Making a call
• Enter Bluetooth mode: [
Pull the battery sheet out from the remote control
unit to the direction of the arrow.
]
• Select a dialing method: [5]/[∞] ➜ [ENT]
• Number dial input:
Input a digit: [0] – [9]
Input “+”: [¢]
Input “#”: [FM]
Input “*”: [AM]
Clear the entered phone number: [4]
• Make a call: [DIRECT]
Changing the battery of the remote control
unit
Receiving a call
Keep on slide
• Answer the call: [
]
• Switch between the private talk mode and the
hands-free talk mode: [ENT]
CR2025
(+side)
Call waiting
Pull out
• Answer Another Incoming Call with the Current
Use a commercially available button battery (CR2025).
Insert the battery with the + and – poles aligned
properly, following the illustration inside the case.
Call Suspended: [
]
• Answer another Incoming Call after Terminating
the Current Call: [SRC]
• Continue the Current Call: [1]
During a call
• End the call: [SRC]
¤ CAUTION
• Do not set the remote control in hot places such
as on the dashboard.
• Lithium battery.
Danger of explosion if the battery is incorrectly
replaced.
Replace only with the same or equivalent type.
• The battery pack or batteries shall not be exposed
to excessive heat such sunshine, fire or the like.
• Keep battery out of reach of children and in
original package until ready to use. Dispose of
used batteries promptly. If swallowed contact
physician immediately.
English
|
61
Appendix
About Audio file
iPod/iPhone that can be connected to this
unit
•
•
•
•
Playable Audio file
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Playable USB device
USB mass storage class
Playable USB device file system
FAT16, FAT32
Made for
• iPod nano (1st generation) • iPod nano (2nd generation)
• iPod nano (3rd generation) • iPod nano (4th generation)
• iPod nano (5th generation) • iPod with video
• iPod classic
• iPod touch (1st generation)
• iPod touch (2nd generation)
Works with
• iPhone
• iPhone 3G • iPhone 3GS
•
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
• Update iPod/iPhone software to the latest version.
• Type of control available varies depending
on the type of connected iPod. See
^
¡
: Folder
Folder
CD
(1)
www.kenwood.com/cs/ce/ipod/ for further details.
:
A
udiofile
¡!
2
• The word “iPod”appearing in this manual indicates
the iPod or the iPhone connected with the iPod
connection cable* (optional accessory).
* Not supported model KCA-iP500.
Refer to the web site for connectable iPod and iPod
connection cable.
3
¡"
¡#
4
¡$
5
¡%
¡P
⁄
• If you start playback after connecting the iPod, the
music that has been played by the iPod is played
first.
An online manual about audio files is put on the site,
www.kenwood.com/cs/ce/audiofile/. On this online
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
In this case, “RESUMING” is displayed without
displaying a folder name, etc. Changing the browse
item will display a correct title, etc.
⁄
• You cannot operate iPod if “KENWOOD”or “✓”
displayed on iPod.
• In this manual, the word “USB device”is used for flash
memories and digital audio players which have USB
terminals.
About USB device
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
|
62 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
• When connecting the USB device, usage of the
CA-U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
About the Bluetooth Audio player
This unit conforms to the following Bluetooth
specifications:
KDC-X994/KDC-BT945U
Version
Profile
Bluetooth Standard Ver. 2.1+EDR
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio/Video Remote Control Profile)
About “KENWOOD Music Editor”
• This unit supports the PC application “KENWOOD
Music Editor Lite ver1.0”or later.
KDC-X794/KDC-MP745U
Version
Profile
Bluetooth Standard Ver. 1.2
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio/Video Remote Control Profile)
• When you use the audio file with database
information added by the “KENWOOD Music Editor
Lite ver1.0”, you can search a file by title, album or
⁄
• In the Instruction manual, the term “Music Editor
media” is used to mean the device that contains
audio files with database information added with
KENWOOD Music Editor.
• A2DP is a profile designed to transfer the music from an
audio player.
• AVRCP is a profile designed to control playback and
selection of music by an audio player.
• “KENWOOD Music Editor Lite ver1.0”is available from
the following web site:
About Satellite Radio tuner (Optional)
This unit supports Satellite Radio tuners which are
released by SIRIUS and XM.
• For further information on “KENWOOD Music Editor
Lite ver1.0”, refer to the site above or the application
help.
Refer to the instruction manual of Satellite radio tuner.
About the Cell-Phone
This unit conforms to the following Bluetooth
specifications:
About HD Radio Reception (Optional)
When you connect an HD Radio tuner, Tuner features
of the unit are disabled and changed to HD Radio
tuner features. With the HD Radio tuner, you can use
the similar functions of Tuner features.
KDC-X994/KDC-BT945U
Version
Profile
Bluetooth Standard Ver. 2.1+EDR
HFP (Hands Free Profile)
OPP (Object Push Profile)
PBAP (Phone Book Access Profile)
SYNC (Synchronization Profile)
KDC-X794/KDC-MP745U
You need to register your cell-phone to your
Bluetooth Unit beforehand. Make sure to read the
instruction manual of the Bluetooth Unit as well.
For the cell-phones verified for compatibility, access
the following URL:
⁄
• The units supporting the Bluetooth function have been
certified for conformity with the Bluetooth Standard
following the procedure prescribed by Bluetooth
SIG. However, it may be impossible for such units to
communicate with your cell-phone depending on its type.
•
•
HFP is a profile used to make a hands-free call.
OPP is a profile used to transfer data such as a phone book
between units.
English
|
63
Appendix
Function items appearing when the iPod source
is selected
Menu List
Common function items
Display
“Settings”
Display
Page
Page
–
“Music”
“Playlists”
“Artists”
“Albums”
“Songs”
“Podcasts”
“Genres”
“Clock & Date”
“Clock Adjust”
“Time Syncronized”
“Date Adjust”
“Date Mode Select”
“DISP & ILLUMI”
“Display Select”
“Type Select”
–
–
“Composers”
“Play Mode”
“iPod by Hand”
“Folder Random”
“All Random”
“File Repeat”
“Side Select”
“Graphic Select”
“Text Select”
“Status”
“Settings”
–
“Color Select”
“Display Off Mode”
“Display Dimmer”
“Contrast”
“DISP N/P”
“TEXT Scroll”
“Skip Search”
“Delete My Playlist”
“Clock & Date”
“DISP & ILLUMI”
“RDS Settings”
–
–
–
“ILLUMI Dimmer”
“ILLUMI Effect”
“ILLUMI MSC SYNC”
“RDS Settings”
“TI”
Function items appearing when the USB source
is selected
Display
“Music”
Page
–
“Play Mode”
“DEMO Mode”
“File Scan”
“Folder Random”
“File Repeat”
“Folder Repeat”
Function items appearing during standby
Display
“Settings”
“Clock & Date”
“DISP & ILLUMI”
“Initial Settings”
“SRC Select”
“Beep”
Page
–
–
–
–
“Settings”
–
–
–
–
“Skip Search”
“Clock & Date”
“DISP & ILLUMI”
“RDS Settings”
“MENU Language”
“Built in AUX”
“Forced CD-DA”
“Favorite Delete”
“Built in AMP”
“DSI”
|
64 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Function items appearing when the Music CD/
Audio file source is selected
Function items appearing when the Hands-Free
source is selected
Display
“Music”
Page
Display
“BT Settings”
Page
–
“Play Mode”
“Phone Selection”
“File Scan”
“Track Scan”
“Folder Random”
“Disc Random”
“Magazine Random”
“File Repeat”
“Audio Selection”
“SMS Download”
“SMS inbox”
“Voice Tag”
“Detailed Setup”
52
–
“Device Regist.”
“Folder Repeat”
“Track Repeat”
“Disc Repeat”
“SPCL DVC Select”
“Device Delete”
“PIN Code Edit”
“Auto Answer”
“Bluetooth HF/Audio”
“Call Beep”
“BT F/W Update”
“Mic Gain”
“NR Level”
“Settings”
–
–
–
–
“Clock & Date”
“DISP & ILLUMI”
“RDS Settings”
Function items appearing when the Tuner
source is selected
Display
“List & Memory”
“FM1”
“FM2”
“Echo Cancel LV“
Page
“Clock & Date”
“DISP & ILLUMI”
“RDS Settings”
–
–
–
Function items appearing when the Bluetooth
Audio source is selected
“FM3”
“AM”
“PTY Search”
“Settings”
22
–
Display
“Settings”
Page
–
“Seek Mode”
“Auto Memory”
“TI”
“Audio Selection”
“Detailed Setup”
“Device Regist.”
–
“Forced MONO”
“Clock & Date”
“DISP & ILLUMI”
“SPCL DVC Select”
“Device Delete”
“PIN Code Edit”
“BT F/W Update”
–
–
–
–
–
Function items appearing when an AUX source
is selected
Display
“Clock & Date”
“DISP & ILLUMI”
“RDS Setting”
Page
–
“Settings”
“AUX Name Set”
–
–
“Clock & Date”
“DISP & ILLUMI”
“RDS Settings”
–
English
|
65
Appendix
Function items appearing when the Satellite
Radio tuner source is selected
Display Indicator items
Source Display Overview
Display
Page
General "ATT"
Indicates that the attenuator is active.
“List & Memory”
“SR1”/“XM1”
“SR2”/“XM2”
“SR3”/“XM3”
“SR4”/“XM4”
“Channel Search”
“Channel Scan”
“Settings”
“FAV”
iPod/USB/ “CD•IN”
Indicates that the Favorite can be registered.
Indicates that a disc is inserted.
Indicates that the Scan function is ON.
Indicates that the File Scan function is ON.
Indicates that the Disc Random function is ON.
Indicates that the Track/File Random function is ON.
CD/CD
Changer
"SCAN"
"SCAN"
“RDM”
“RDM”
–
“Fo•RDM” Indicates that the Folder Random function is ON.
“M•RDM” Indicates that the Magazine Random function is ON.
“ALL•RDM” Indicates that the All Random function is ON.
“PL•RDM” Indicates that the Playlist Random function is ON.
“DMS•RDM” Indicates that the DMS Random function is ON.
“DMS•REP” Indicates that the DMS Repeat function is ON.
“D•REP” Indicates that the Disc Repeat function is ON.
“Seek Mode”
“ESN”
“Clock & Date”
“DISP & ILLUMI”
“RDS Settings”
–
–
–
“T•REP”
Indicates that the Track Repeat function is ON.
“Fo•REP” Indicates that the Folder Repeat function is ON.
“Fi•REP” Indicates that the File Repeat function is ON.
Function items appearing when the HD Radio™
tuner source is selected
“P•REP”
"REP"
“MP3”
“WMA”
“AAC”
Indicates that the Playlist Repeat function is ON.
Indicates that the Repeat function is ON.
Identifies the MP3 file.
Identifies the WMA file.
Identifies the AAC-LC file.
Display
“List & Memory”
“FM1”
Page
“FM2”
“FM3”
“MYLIST” Indicates that the My Playlist mode is selected now.
Tuner
“RDS”
"ST"
"TI"
Indicates the RDS is being received.
“AM”
“Settings”
Indicates that stereo broadcast is being received.
Indicates the reception state of traffic information. (On: TI
is being received. Blinking: TI is not being received.)
Indicates that analog broadcast is being received.
Indicates that digital broadcast is being received.
Indicates whether the reception channel is main or sub.
(On: The channel is main. Blinking: The channel is sub.)
Indicates that Multi channel is being received.
Indicates that stereo broadcast is being received.
Indicates that Tagging is enabled.
–
“Seek Mode”
“Auto Memory”
“Receive Mode”
“TAG Memory”
“Tagging”
“Radio ID Watch”
“Clock & Date”
“DISP & ILLUMI”
HD Radio "HD A"
"HD D"
"M/S"
"MC"
"ST"
“TAG”
–
–
Hands- “C-Wait” Indicates call-waiting.
Free
“PRIVATE” Indicates a cell-phone call in progress.
"BT"
Indicates that the Bluetooth function can be used.
Indicates that battery level of cell-phone.
Full
Nearly dead
Indicates that the battery level of cell-phone cannot be
obtained.
Indicates that signal strength of cell-phone.
Maximum
Minimum
Indicates the out of coverage zone.
Indicates that the signal strength of cell-phone cannot
be obtained.
|
66 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
English
|
67
Appendix
IC (Industry Canada) Notice
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation
of the device.
The term “IC: ” before the certification/registration
number only signifies that the Industry Canada
technical specification were met.
2CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
In compliance with Federal Regulations, following
are reproductions of labels on, or inside the product
relating to laser product safety.
Kenwood Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI
TOKYO, JAPAN
This product contains a CR Coin Cell Lithium Battery
which contains Perchlorate Material – special handling
may apply.
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS N0.21 CFR
1040. 10, CHAPTER 1, SUBCHAPTER J.
Location : Top Panel
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless
the modifications are expressly approved in the
instruction manual. The user could lose the authority
to operate this equipment if an unauthorized change
or modification is made.
FCC NOTE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment may cause harmful interference to radio
communications, if it is not installed and used in
accordance with the instructions. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
•
HD Radio™ Technology Manufactured Under License
From iBiquity Digital Corp. U.S. and Foreign Patents. HD
Radio™ and the HD Radio Ready logos are proprietary
trademarks of iBiquity Digital Corp.
•
•
The “AAC”logo is a trademark of Dolby Laboratories.
The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Kenwood Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
•
•
iTunes is a trademark of Apple Inc.
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
•
•
iPhone is a trademark of Apple Inc.
“Made for iPod”means that an electronic accessory
has been designed to connect specifically to iPod and
has been certified by the developer to meet Apple
performance standards.
•
•
“Works with iPhone”means that an electronic
accessory has been designed to connect specifically
to iPhone and has been certified by the developer to
meet Apple performance standards.
• Consult the dealer or an experienced radio/TV
technician for help.
•
Contains Transmitter Module
FCC ID : RKXCK5050NEW
Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
•
Contains Transmitter Module
IC ID : 5119A-CK5050NEW
|
68 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Accessories/ Installation Procedure
checked.
Accessories
• If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
• If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
• If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
• Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
1
2
4
..........1
..........4
..........2
3
..........4
5*
3 m (9.5 ft) ..........1
• When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
• Reception may drop if there are metal objects near the
Bluetooth antenna.
*Accessory of KDC-X994/ KDC-BT945U
Installation Procedure
1
To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2
Make the proper input and output wire
connections for each unit.
3
4
Connect the speaker wires of the wiring harness.
Connect the wiring harness wires in the following
order: ground, battery, ignition.
5
6
7
8
Connect the wiring harness connector to the unit.
Install the unit in your car.
Reconnect the - battery.
Bluetooth antenna unit
Press the reset button.
About CD players/disc changers connected
to this unit
2WARNING
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
If the CD player/ disc changer has the “O-N” switch, set
it to the “N” position.
The functions you can use and the information that
can be displayed may differ depending on the models
being connected.
¤
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
For Good Reception
To assure good reception, note the following:
• Make sure to ground the unit to a negative 12V DC power
supply.
• Communicate with the cell-phone within the line-
of-sight distance of 10 m (30 ft). The communication
range becomes shorter depending on the
surrounding environment. The communication
range also becomes shorter when there is an
obstacle between this unit and the cell-phone. The
above maximum communication range (10 m) is
not always assured.
• Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
• Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
• If the power is not turned ON (“PROTECT”is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
• A broadcast station or walkie-talkie located nearby
can interfere with communication due to too strong
signal.
English
|
69
Connecting Wires to Terminals
Rear output
Do not remove the cap
R
L
To USB device
USB connector (1m)
⁄
Front output
when you do not use the
USB cable. The connector
will cause the unit to
malfunction if it gets in
touch with any metallic
part of the vehicle.
Sub Woofer output
Microphone
input (KDC-X994 /
KDC-BT945Uonly)
Antenna Cord
Microphone
(Accessory5)
FM/AM antenna input
R
L
AUX input (Stereo)
Use the mini-plug which is stereo type
and does not have any resistance.
Fuse (10A)
Wiring harness
(Accessory1)
To Kenwood disc changer/ External optional accessory
To connect these leads, refer to the relevant
⁄
instruction manuals.
White
To front left speaker
White/Black
Gray
Gray/Black
To front right speaker
To rear left speaker
To rear right speaker
Green
Green/Black
Purple
Purple/Black
If no connections are made, do not let the wire come out from the tab.
Power control wire (Blue/White)
Motor antenna control wire (Blue)
When using the optional power amplifier, connect to its power control
terminal.
P.CONT
Depending on what antenna you are using, connect either to the control
terminal of the motor antenna, or to the power terminal for the booster
amplifier of the film-type or short pole type antenna.
ANT.
CONT
Mute control wire (Brown)
Connect to the terminal that is grounded when either the telephone
rings or during conversation. (KDC-X794/KDC-MP745U only)
MUTE
To connect the Kenwood navigation system, consult your
⁄
navigation manual.
Dimmer control wire (Orange / White)
To car light control switch
ILLUMI
Steering remote control (Light Blue/Yellow)
To use the steering wheel remote control feature, you need to an
exclusive remote adapter (not supplied) matches your car is required.
REMOTE
CONT
STEERING
WHEEL
REMOTE
INPUT
Car fuse
box
Ignition key
switch
Ignition wire (Red)
ACC
Car fuse box
(Main fuse)
Battery wire (Yellow)
Ground wire (Black) · (To car chassis)
+
–
Battery
|
70 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Installation/Removing the Unit
non-Japanese cars
Removing the hard rubber frame
1
Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
Lock
Catch
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Accessory2
⁄
Removal tool
• Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
2
When the upper level is removed, remove the
lower two locations.
⁄
• The frame can be removed from the bottom side in the
same manner.
Japanese cars
1
Refer to the section <Removing the hard rubber
frame> and then remove the hard rubber frame.
Removing the Unit
2
Align the holes in the unit (two locations on each
side) with the vehicle mounting bracket and secure
the unit with the accessory screws.
1
Refer to the section <Removing the hard rubber
frame> and then remove the hard rubber frame.
2
3
Detach the faceplate.
Insert the two removal tools deeply into the slots
on each side, as shown.
Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
T
N
T/N
T
N
4
T: Toyota cars
N: Nissan cars
Accessory2
8 mm
MAX.
8mm
MAX.
3
4
ø5mm
ø5mm
Accessory3...for Nissan car
Accessory4...for Toyota car
¤
• Be careful to avoid injury from the catch pins on the
removal tool.
¤ CAUTION
Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during and
shortly after the use of the unit. Metal part such as
the heat sink and enclosure become hot.
5
Pull the unit all the way out with your hands, being
careful not to drop it.
English
|
71
Installation/Removing the Unit
Accessory of KDC-X994/ KDC-BT945U
Installation the Microphone Unit
1
Check the installation position of the microphone
(accessory 5).
2
Remove oil and other dirt from the installation
surface.
3
4
Install the microphone.
Wire the cable up to the unit with it secured at
several positions using tape or the like.
Accessory 5
Fix a cable with a commercial
item of tape.
Peel the release coated paper of double-face adhesive tape to
fix on the place shown above.
Adjust the direction of the microphone to the driver.
⁄
• Install the microphone as far as possible from the cell-
phone.
|
72 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
!
• Cannot set up the subwoofer.
• No output from the subwoofer.
• Cannot set up the subwoofer position of Manual
position setting.
General
? The operation check sound (beep sound) does not
• In the speaker select option, None is selected for
sound.
The preout jack is being used.
The Touch Sensor Tone cannot be output from
the preout jack.
? The illumination flashes when the knob or button
is operated.
!
• Cannot set up the equalizer.
• Cannot set up the Bass Boost.
• Cannot set up the Highway sound.
• Cannot set up the Supreme.
• Cannot set up the Position control.
• In the speaker select option, None is selected for
This is the key illumination effect.
You set this effect in “ILLUMI Effect” of <Display
? The key illumination effect brought about in
conjunction with the sound volume is small.
The key illumination effect may be insufficient
depending on the sound volume and sound quality.
Tuner source
? Radio reception is poor.
!
• Cannot select the output destination of the
subsource in the Dual zone.
• Cannot adjust the volume of the rear speakers.
The car antenna is not extended.
Pull the antenna out all the way.
Disc source
? The specified disc does not play, but another one
!
!
!
Cannot set up Display.
turned off.
plays instead.
The specified CD is quite dirty.
Clean the CD, referring to the CD cleaning of the
Cannot switch to USB/iPod source.
The disc is loaded in a different slot from that
specified.
Eject the disc magazine and check the number
for the specified disc.
The disc is severely scratched.
Try another disc instead.
The number of songs contained in “SONGS”
category of this unit is different from that
contained in “SONGS” category of iPod.
Podcast files are not counted in this unit as this unit
does not support the playback of podcast files.
Audio file source
? The sound skips when an Audio file is being
played.
The media is scratched or dirty.
Clean the media, referring to the CD cleaning of
The recording condition is bad.
Record the media again or use another media.
English
|
73
Troubleshooting Guide
Hands-free
The messages shown below display your
systems condition.
? The hands-free talk volume is low.
The hands-free talk volume is set at a low level.
TOC Error:
• No disc has been loaded in the disc
magazine.
The hands-free talk volume can be adjusted
independently. Adjust it during hands-free talk.
“Mic Gain” and “NR Level” <Bluetooth Setting>
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
ERROR 05:
The disc is unreadable.
? No sound is heard from the rear speakers.
You are talking in the hand-free talk mode.
ERROR 77/Mecha Error:
The unit is malfunctioning for some reason.
No sound is heard from the rear speakers in the
hands-free talk mode.
Press the reset button on the unit. If the
“ERROR 77”/“Mecha Error” code does not
disappear, consult your nearest service
center.
? No beep is heard at reception of an incoming call.
No beep is heard depending on the type of your
cell-phone.
ERROR 99:
Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
Check the disc magazine. And then press
the reset button on the unit. If the “ERROR
99” code does not disappear, consult your
nearest service center.
set ON.
? Voice is not recognized.
The vehicle window is open.
If the surrounding noise is large, voice cannot be
recognized properly. Close the vehicle windows
to reduce noise.
CD-IN (Blink): The CD player section is not operating
properly.
Small voice.
If voice is too small, it cannot be recognized
Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
properly. Speak into the microphone a little more
loudly and naturally.
The person uttering the voice tag is not the one who
registered the it.
Only the voice of the person who registered the
voice tag can be recognized.
Protect (Blink):
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
Wire or insulate the speaker cable properly
and press the reset button. If the “Protect”
code does not disappear, consult your
nearest service center.
Bluetooth audio source
? The Bluetooth audio player cannot be registered
(pairing).
The PIN code is fixed.
When a PIN code is specified in the Instruction
Manual for Bluetooth Audio Player, register it
with reference to <Registering PIN Code> (page
50) to register the Bluetooth audio player. If no PIN
code is specified in the Instruction Manual, try
“0000”.
Unsupported File:
An Audio file is played with a format that this
unit can’t support.
Copy Protection:
A copy-protected file is played.
Read Error:
No Device:
The file system of the connected USB device
is broken.
Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
? The sound from the Bluetooth audio player is
discontinuous.
The distance between this unit and audio player is
too far.
Move the audio player nearer to this unit.
Another Bluetooth device is affecting the Bluetooth
communication.
The USB device is selected as a source
although no USB device is connected.
Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
Turn off another Bluetooth device.
Move another Bluetooth device away from this
unit.
Another Bluetooth device or profile is used for
communication.
The downloading of the Phone book or the SMS
disconnects the sound.
|
74 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
N/A Device:
• An unsupported USB device is connected.
• Connection to the iPod has failed.
Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 62) for information on supported
iPods.
Err No Matching:
The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
Too Soft:
Too Loud:
Too Long:
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
No Music Data/Error 15:
• The connected USB device contains no
The word or utterance is too long to be
recognized.
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
No Phonebook: Data is not contained in the phone book.
No Message: No short message in In Box.
USB ERROR:
iPod Error:
Some trouble may have occurred to the
connected USB device.
Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
No Record:
The voice tag is not registered in the phone
book.
Memory Full: The number of voice tags reaches the
maximum number to be registered in the
phone book.
Connection to the iPod has failed.
Remove the USB device and then
reconnect it.
Confirm that the software for the iPod is
the latest version.
Favorite: No Memory:
The procedure is not registered to Favorite
Preset Memory
USB REMOVE (Blink):
The Remove mode has been selected for the
No Access:
No Voice:
The procedure preset with Favorite Control
cannot be available. The preset content may
not be recalled depending on the selected
source or mode.
USB device/iPod. You can remove the USB
device/iPod safely.
No Number:
No Data:
• The calling party does not notify a caller ID.
• There is no phone number data.
No call.
• There is no outgoing call list.
• There is no incoming call list.
• There is no missed call list.
• There is no phone book list.
No Entry:
The cell-phone has not been registered
(pairing).
HF Disconnect: The unit cannot communicate with the cell-
phone.
HF Error 07:
The memory cannot be accessed.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
HF Error 68:
The unit cannot communicate with the cell-
phone.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
Un Known:
Device Full:
The Bluetooth device cannot be detected.
5 Bluetooth device have already been
registered. No more Bluetooth device cannot
be registered.
PIN Code NG: The PIN code is wrong.
Connect NG: The unit cannot be connected to the device.
Pairing Failed: Pairing error.
English
|
75
Specifications
FM tuner section
USB Interface
Frequency range (200 kHz space)
: 87.9 MHz – 107.9 MHz
USB Standard
: USB1.1/ 2.0 (Full speed)
Usable sensitivity (S/N = 30dB)
: 9.3dBf (0.8 μV/75 Ω)
Maximum Supply current
: 500 mA
Quieting Sensitivity (S/N = 50dB)
: 15.2dBf (1.6 μV/75 Ω)
File System
: FAT16/ 32
Frequency response ( 3 dB)
: 30 Hz – 15 kHz
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
Signal to Noise ratio (MONO)
: 70 dB
WMA decode
: Compliant with Windows Media Audio
Selectivity (±400 kHz)
: ≥ 80 dB
AAC decode
: AAC-LC ”.m4a” files
Stereo separation (1 kHz)
: 40 dB
CD player section
Laser diode
: GaAlAs
AM tuner section
Frequency range (10 kHz space)
: 530 kHz – 1700 kHz
Digital filter (D/A)
: 8 Times Over Sampling
Usable sensitivity (S/N = 20dB)
: 28 dBµ (25 µV)
D/A Converter
: 24 Bit
Spindle speed
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Frequency response (±1 dB)
: 10 Hz – 20 kHz
Total harmonic distortion (1 kHz)
: 0.008 %
Signal to Noise ratio (1 kHz)
KDC-X994/KDC-X794: 110 dB
KDC-BT945U/KDC-MP745U: 105 dB
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
Bluetooth section
(KDC-X994/ KDC-BT945U
)
Version
: Bluetooth Ver.2.1+EDR Certified
Frequency range
: 2.402 – 2.480 GHz
Output Power
: +4dBm (MAX), 0dBm (AVE) Power Class 2
Maximum Communication range
: Line of sight approx.10m (32.8 ft)
Profiles
: HFP (Hands Free Profile)
: HSP (Headset Profile)
: SPP (Serial Port Profile)
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC “.m4a” files
: PBAP (Phone Book Access Profile)
: OPP (Object Push Profile)
: SYNC (Synchronization Profile)
: A2DP (Advanced Audio Distribution Profile)
: AVRCP (Audio/Video Remote Control Profile)
|
76 KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
Audio section
Maximum output power
: 50 W x 4
Full Bandwidth Power (at less than 1% THD)
: 22 W x 4
Speaker Impedance
: 4 – 8 Ω
Tone action (KDC-X994/KDC-X794)
BAND1 (60 Hz): ±9 dB
BAND2 (250 Hz): ±9 dB
BAND3 (1 kHz): ±9 dB
BAND4 (4 kHz): 9 dB
BAND5 (16 kHz): ±9 dB
Tone action (KDC-BT945U/KDC-MP745U)
BAND1 : 60 Hz - 400 Hz ±9 dB
BAND2 : 630 Hz - 2.5 kHz ±9 dB
BAND3 : 4.0 kHz - 16 kHz ±9 dB
Preout level / Load (CD)
KDC-X994/KDC-X794/KDC-BT945U
: 4000 mV/10 kΩ
KDC-MP745U: 2500 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
Auxiliary input
Frequency response (±1 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
General
Operating voltage
KDC-X994/KDC-BT945U (10.5 – 16V allowable)
: 14.4 V
KDC-X794/KDC-MP745U (11 – 16V allowable)
: 14.4 V
Maximum Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 53 x 158 mm
7-3/16 x 2-1/16 x 6-1/4 inch
Weight
: 2.9 lbs (1.30 kg)
•
Specifications subject to change without notice.
English
|
77
This symbol mark indicates that
Kenwood manufactured this product
so as to decrease harmful influence on
the environment.
|