KENWOOD KDC 162U User Manual

KDC-262U  
KDC-162U  
KDC-122U  
KDC-MP262U  
KDC-MP162U  
KDC-220U  
CIND-SRETCERIVUERCTION MANUAL  
AMMOPLID-TUENDERLEECMTEPURLDOEICD  
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM  
MANUAL DE INSTRUCCIONES  
Take the time to read through this instruction manual.  
Familiarity with installation and operation procedures will help  
you obtain the best performance from your new CD-receiver.  
For your records  
Record the serial number, found on the back of the unit, in the  
spaces designated on the warranty card, and in the space provided  
below. Refer to the model and serial numbers whenever you  
call upon your Kenwood dealer for information or service on the  
product.  
Model KDC-262U/ KDC-162U/ KDC-122U/ KDC-MP262U/  
KDC-MP162U/ KDC-220U  
Serial number  
US Residents Only  
Register Online  
Register your Kenwood product at www.Kenwoodusa.com  
© 2014 JVC KENWOOD Corporation  
B5A-0137-00 (KN)  
BASICS  
Faceplate  
Remote control (RC-406)  
Remote sensor (Do not  
Attach  
Detach  
Display window  
Loading slot  
expose to bright sunlight.)  
Volume knob  
(turn/press)  
Pull out the  
insulation  
sheet when  
using for the  
first time.  
*
Not used  
How to reset  
How to replace the battery  
Detach button  
Your preset  
adjustments will  
also be erased.  
To  
On the faceplate  
On the remote control  
Turn on the power  
Press and hold SRC to turn off the power.  
( Pressing SRC does not turn on the power. )  
Press  
.
• Press and hold to turn off the power.  
Adjust the volume  
Turn the volume knob.  
Press  
or  
.
Press ATT during playback to attenuate the sound.  
• Press again to cancel.  
Select a source  
Press SRC repeatedly.  
Press  
Press  
repeatedly.  
repeatedly.  
Change the display  
information*  
( not available )  
• Press and hold to scroll the current display information.  
* For  
/
: You can also select to turn off the display information by pressing  
repeatedly.  
3
ENGLISH  
GETTING STARTED  
3
Set the initial settings  
Press  
1
2
3
repeatedly to enter STANDBY.  
Press the volume knob to enter [FUNCTION].  
Turn the volume knob to make a selection (see the following table),  
then press the knob.  
4
5
Repeat step 3 until the desired item is selected or activated.  
Press and hold  
to exit.  
1
To return to the previous setting item, press  
.
Cancel the demonstration  
When you turn on the power (or after you reset the unit), the display  
shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”  
Default: XX  
AUDIO CONTROL  
1
Press the volume knob.  
[
YES] is selected for the initial setup.  
SWITCH  
PREOUT  
REAR/ SUB-W or REAR/ SUBWOOFER: Selects whether rear speakers or  
a subwoofer are connected to the line out terminals on the rear (through  
an external amplifier).  
2
Press the volume knob again.  
“DEMO OFF” appears.  
SP SELECT  
OFF/ 5/4/ 6 × 9/6/ OEM: Selects according to the speaker size (5 inches  
or 4 inches, 6×9 inches or 6 inches) or OEM speakers for optimum  
performance.  
2
Set the clock  
1
2
3
4
Press the volume knob to enter [FUNCTION].  
Turn the volume knob to select [CLOCK], then press the knob.  
Turn the volume knob to select [CLOCK ADJUST], then press the knob.  
Turn the volume knob to make the settings, then press the knob.  
Day Hour Minute  
DISPLAY  
EASY MENU  
(For  
/
)
ON: Both display and button illumination change to white color when  
entering [FUNCTION]. ; OFF: Both display and button illumination  
remain as [COLOR SELECT] color. ( 12  
5
6
7
Turn the volume knob to select [CLOCK FORMAT], then press the knob.  
Turn the volume knob to select [12H] or [24H], then press the knob.  
)
Press and hold  
to exit.  
TUNER SETTING  
PRESET TYPE  
To return to the previous setting item, press  
.
NORMAL: Memorizes one station for each preset button in each band  
(FM1/ FM2/ FM3/ AM). ; MIX: Memorizes one station for each preset  
button, regardless of the selected band.  
(For  
/
/
/
)
While in clock display screen...  
Press and hold  
to enter clock adjustment mode directly.  
Then, perform step 4 to set the clock.  
4
GETTING STARTED  
RADIO  
SYSTEM  
KEY BEEP  
ON: Activates the keypress tone. ;  
OFF: Deactivates.  
SOURCE SELECT  
PANDORA SRC ON: Enables PANDORA in source selection. ;  
OFF: Disables. (  
9
)
Search for a station  
IHEART SRC  
ON: Enables IHEARTRADIO in source selection. ;  
OFF: Disables. ( 10  
1
2
Press  
repeatedly to select TUNER.  
repeatedly (or press  
)
Press  
/
on RC-406) to select FM1/ FM2/  
BUILT-IN AUX ON: Enables AUX in source selection. ;  
OFF: Disables. (  
FM3/ AM.  
6
)
3
Press S/ T(or press S/  
on RC-406) to search for a station.  
CD READ  
1
: Automatically distinguishes between audio file  
To change the searching method for S/ T: Press  
AUTO1 : Automatically search for a station.  
AUTO2 : Search for a preset station.  
repeatedly.  
disc and music CD. ; : Forces to play as a music  
CD. No sound can be heard if an audio file disc  
is played.  
2
MANUAL : Manually search for a station.  
To store a station: Press and hold one of the number buttons (1 to 6).  
To select a stored station: Press one of the number buttons (1 to 6) (or press one of the  
number buttons (1 to 6) on RC-406).  
F/W UPDATE  
UPDATE SYSTEM  
F/W UP xx.xx YES: Starts upgrading the firmware. ; NO: Cancels  
(upgrading is not activated).  
Direct Access Tuning (using RC-406)  
1
2
3
Press DIRECT to enter Direct Access Tuning.  
For details on how to update the firmware, see:  
Press the number buttons to enter a frequency.  
Press  
to search for a station.  
CLOCK  
• To cancel, press  
or DIRECT.  
CLOCK DISPLAY ON: The clock time is shown on the display even  
• If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically  
when the unit is turned off. ; OFF: Cancels.  
canceled.  
Other settings  
1
2
3
4
Press the volume knob to enter [FUNCTION].  
Turn the volume knob to make a selection (  
6), then press the knob.  
Repeat step 2 until the desired item is selected or activated.  
Press and hold  
to exit.  
To return to the previous setting item, press  
.
5
ENGLISH  
RADIO  
AUX  
Default: XX Preparation:  
Select [ON] for [BUILT-IN AUX]. (  
5)  
TUNER SETTING  
Start listening  
AUTO  
MEMORY  
YES: Automatically starts memorizing 6 stations with good reception. ; NO: Cancels.  
Selectable only if [NORMAL] is selected for [PRESET TYPE]. (  
4)  
1
Connect a portable audio player (commercially  
available).  
MONO SET  
NEWS SET*  
REGIONAL*  
AF SET*  
ON: Improves the FM reception, but the stereo effect may be lost. ; OFF: Cancels.  
ON: The unit will temporarily switch to News Programme if available. ; OFF: Cancels.  
ON: Switches to another station only in the specific region using the “AF” control. ; OFF: Cancels.  
Auxiliary input jack  
Portable audio  
player  
ON: Automatically searches for another station broadcasting the same program in the same Radio  
Data System network with better reception when the current reception is poor. ; OFF: Cancels.  
TI*  
ON: Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up). ;  
OFF: Cancels.  
3.5 mm (1/8") stereo mini plug with “L”  
shaped connector (commercially available)  
PTY SEARCH*  
CLOCK  
Selects the available Program Type (see below), then, press  
S
/ Tto start.  
2
3
Press  
repeatedly to select AUX.  
Turn on the portable audio player and start  
playback.  
TIME SYNC*  
ON: Synchronizes the unit’s time to the Radio Data System station time. ; OFF: Cancels.  
: Only for FM source.  
*
For  
/
Set the AUX name  
While listening to a portable audio player connected to  
the unit...  
• [MONO SET]/ [NEWS SET]/ [REGIONAL]/ [AF SET]/ [TI]/ [PTY SEARCH] is selectable only when the  
band is FM1/ FM2/ FM3.  
1
Press the volume knob to enter [FUNCTION].  
Turn the volume knob to select [SYSTEM], then  
press the knob.  
Turn the volume knob to select [AUX NAME SET],  
then press the knob.  
• Available Program Type:  
2
SPEECH  
:
NEWS  
WEATHER  
POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS  
(music), JAZZ COUNTRY NATION M (music), OLDIES FOLK M (music)  
,
AFFAIRS  
,
INFO (information), SPORT  
,
EDUCATE  
,
DRAMA  
,
CULTURE  
,
SCIENCE  
DOCUMENT  
OTHER M  
,
VARIED,  
,
FINANCE  
,
CHILDREN SOCIAL RELIGION  
,
,
,
PHONE IN  
,
TRAVEL  
,
LEISURE  
,
3
4
MUSIC  
:
,
,
,
,
Turn the volume knob to make a selection, then  
press the knob.  
The unit will search for the Program Type categorized under [SPEECH] or [MUSIC] if selected.  
• If the volume is adjusted during reception of traffic information or news bulletin, the  
adjusted volume is memorized automatically. It will be applied the next time traffic  
information or news bulletin is turned on.  
AUX (default)/ DVD PORTABLE/ GAME/ VIDEO/ TV  
/
5
Press and hold  
to exit.  
To return to the previous setting item, press  
.
6
CD / USB / iPod / ANDROID  
Start playback  
The source changes automatically and  
playback starts.  
M
Eject disc  
Label side  
To  
On the faceplate  
On the remote control  
Playback / pause  
Reverse / Fast-forward  
Press  
.
Press  
.
4
*
USB input terminal  
Press and hold S/ T.  
Press S/ T.  
Press and hold S/  
.
Select a track/file  
USB  
Press S/  
.
5
*
Select a folder  
Press  
/
.
Press J/ K.  
6
*
CA-U1EX (max.: 500 mA)  
(optional accessory)  
Repeat play  
Press  
TRACK REPEAT  
FILE REPEAT  
repeatedly.  
/
REPEAT OFF  
FOLDER REPEAT  
: Audio CD  
/
/
REPEAT OFF : MP3/WMA/WAV file, iPod or  
iPod/iPhone  
(except for  
)
ANDROID  
*
: KME Light/ KMC file  
/
7
FILE REPEAT  
/
REPEAT OFF  
6
*
Random play  
Press  
DISC RANDOM  
FOLDER RANDOM  
or  
/
repeatedly.  
RANDOM OFF : Audio CD  
KCA-iP102 / KCA-iP103 (optional  
accessory) 1 or accessory cable  
*
/
RANDOM OFF : MP3/WMA/WAV file, KME Light/ KMC  
2
*
of the iPod/iPhone  
file, iPod or ANDROID  
8
*
to select ALL RANDOM.  
Press and hold  
or  
3
*
ANDROID  
Select control mode  
Select music drive  
While in iPod source, press and hold iPod.  
9
*
MODE ON : Control from the iPod  
MODE OFF : Control from the unit  
2
*
While in ANDROID source,  
(
8, [ANDROID SETUP])  
Micro USB 2.0 cable  
(commercially available)  
Press 5 repeatedly.  
(
8, [MUSIC DRIVE]  
)
The stored songs in the following start playback.  
• Selected internal or external memory of a smartphone (Mass Storage  
Class).  
1
*
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type  
Do not leave the cable inside the car when not using.  
2
• Selected drive of a multiple drives device.  
7
ENGLISH  
CD / USB / iPod / ANDROID  
3
*
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is  
shown. Follow the instructions to install the application. You can also install the latest version  
of KENWOOD MUSIC PLAY application on your Android device before connecting. ( 14).  
Direct Music Search (using RC-406)  
1
2
3
Press DIRECT.  
4
5
6
7
8
9
Press the number buttons to enter a track/file number.  
*
*
*
*
*
*
For ANDROID: Applicable only when [BROWSE MODE] is selected. (  
For CD: Only for MP3/WMA files. This does not work for iPod/ ANDROID.  
For iPod/ ANDROID: Applicable only when [MODE OFF]/ [BROWSE MODE] is selected.  
[ANDROID SETUP])  
Press  
to search for music.  
• To cancel, press  
or DIRECT.  
KME Light : KENWOOD Music Editor Light, KMC : KENWOOD Music Control ( 14  
For CD: Only for MP3/WMA files.  
)
• Not available if Random Play is selected.  
• Not applicable for iPod, ANDROID, KME Light/ KMC file.  
You can still play/pause, file skip, fast-forward or reverse files from the unit.  
Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo  
Select a file from a folder/list  
Press  
While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect  
the iPod/iPhone to the USB input terminal of the unit.  
• The unit will output the sound from these applications.  
1
2
3
.
Turn the volume knob to select a folder/list, then press the knob.  
Turn the volume knob to select a file, then press the knob.  
Other settings  
Quick Search  
1
2
Press the volume knob to enter [FUNCTION].  
If you have many files, you can search through them quickly.  
Turn the volume knob to make a selection (see the following  
table), then press the knob.  
For USB (for KME Light/ KMC files):  
Press S/ Tto search at a preset skip search ratio. (  
[SKIP SEARCH])  
3
4
Repeat step 2 until the desired item is selected or activated.  
Press and hold S/ Tto search at a 10 ratio.  
Not applicable for CD and MP3/WMA/WAV files.  
%
Press and hold  
to exit.  
To return to the previous setting item, press  
.
For iPod:  
Default: XX  
You can search for a file according to the first character.  
Turn the volume knob quickly to enter character search.  
Turn the volume knob to select the character.  
ANDROID SETUP  
BROWSE MODE: Control from the unit (using KENWOOD MUSIC PLAY application). ;  
HAND MODE: Control other media player applications from the Android device  
(without using KENWOOD MUSIC PLAY application). However, you can still play/pause  
and file skip from the unit.  
To search for a character other than A to Z and 0 to 9, enter only “ ”.  
*
Press S/ Tto move to the entry position.  
• You can enter up to 3 characters.  
Press the volume knob to start searching.  
USB  
• To return to the root folder/ first file/ top menu, press 5.  
• To return to the previous setting item, press  
• To cancel, press and hold  
• For iPod, applicable only when [MODE OFF] is selected. (  
• For ANDROID, applicable only when [BROWSE MODE] is selected.  
ANDROID SETUP])  
MUSIC DRIVE DRIVE CHANGE: The next drive ([DRIVE 1] to [DRIVE 5]) is selected  
.
automatically and playback starts.  
.
Repeat steps  
SKIP SEARCH 0.5% 1% 5%  
Light/ KMC file, selects the skip search ratio over the total files.  
1
to  
3
to select the following drives.  
7)  
/
/
/
10%: While listening to iPod, ANDROID or KME  
(
[
8
Pandora® (for  
Preparation:  
/
/
)
Create and save a new station  
Install the latest version of the Pandora application on your device  
(iPhone/ iPod touch), then create an account and log in to Pandora.  
1
2
Press and hold the volume knob.  
Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then  
press the knob.  
• Select [ON] for [PANDORA SRC]. (  
5)  
Start listening  
A new station is created based on the current song or artist.  
Press and hold one of the number buttons (1 to 5) to store.  
3
1
2
Open the Pandora application on your device.  
Connect your device to the USB input terminal.  
To select a stored station, press one of the number buttons (1 to 5).  
USB input terminal  
Search for a registered station  
1
2
Press  
.
Turn the volume knob to make a selection, then press the knob.  
[
[
BY DATE]: According to the registered date  
KCA-iP102 / KCA-iP103 (optional  
A-Z]: Alphabetical order  
accessory) 1 or accessory cable of  
*
3
Turn the volume knob to the desired station, then press the knob.  
2
*
the iPod/iPhone  
To cancel, press and hold  
(or using RC-406)  
.
The source changes to PANDORA and broadcast starts.  
Press J/ Kto search for a station, then press  
.
To  
On the faceplate  
On the remote control  
Playback / pause  
Skip a track  
Press  
.
Press  
Press  
Press  
.
Bookmark a song or artist information  
.
Press T.  
Press  
1
2
Press and hold J.  
Thumbs up or thumbs  
/
.
/
.
Turn the volume knob to make a selection, then press the knob.  
3
*
down  
[
THIS TRACK]: Current song information  
THIS ARTIST]: Current artist information  
[
1
*
*
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type  
Do not leave the cable inside the car when not using.  
If thumbs down is selected, the current track is skipped.  
“BOOKMARKED” appears and the information is stored to your device.  
The bookmark is available on your Pandora account but not on this  
unit.  
2
3
9
ENGLISH  
iHeartRadio® (for  
Preparation:  
/
/
)
Search for a station  
Press  
Install the latest version of iHeart Link for KENWOOD application on your  
device (iPhone/ iPod touch), then create an account and log in to iHeartRadio.  
1
2
.
Turn the volume knob to select a category, then press the  
• Select [ON] for [IHEART SRC]. (  
5)  
knob.  
Start listening  
3
Turn the volume knob to the desired station, then press the  
knob.  
1
2
Open the iHeart Link application on your device.  
Connect your device to the USB input terminal.  
When a city list appears, you can skip cities in alphabetical order.  
To cancel, press and hold  
(or using RC-406)  
.
USB input terminal  
Press J/ Kto search for a station, then press  
.
Skip cities by alphabetical order  
KCA-iP102 / KCA-iP103 (optional  
While a city list appears during search...  
accessory) 1 or accessory cable of  
*
2
1
2
Turn the volume knob quickly to enter character search.  
*
the iPod/iPhone  
repeatedly to select IHEARTRADIO.  
Broadcast starts automatically.  
Turn the volume knob or press S/ Tto select the  
3
Press  
character to be searched for.  
3
4
Press J/ Kto move to the previous/next page.  
Press the volume knob to start searching.  
To  
On the faceplate  
On the remote control  
To cancel, press and hold  
.
Playback / pause  
Press  
.
Press  
Press  
.
Delete a station  
Skip a track for custom station  
.
Press T.  
Press  
While listening to IHEARTRADIO...  
3
*
Thumbs up or thumbs down  
for custom station  
/
.
1
2
3
Press the volume knob to enter [FUNCTION].  
Turn the volume knob to select [SYSTEM], then press the knob.  
Turn the volume knob to select [STATION DEL], then press the  
knob.  
Create a new/custom station  
Press 1.  
Add to favorite stations for  
live station  
Press 2.  
4
5
Turn the volume knob to select [LIVE] or [CUSTOM], then press  
the knob.  
Turn the volume knob to select the desired station to delete,  
then press the knob.  
Turn the volume knob to select [YES], then press the knob.  
Press and hold  
Scan for live station  
Press 5.  
1
*
*
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type  
Do not leave the cable inside the car when not using.  
If thumbs down is selected, the current track is skipped.  
6
7
2
3
to exit.  
To return to the previous setting item, press  
.
10  
AUDIO SETTINGS  
While listening to any source...  
PRESET EQ  
DRIVE EQ  
NATURAL  
genre. (Select [USER] to use the customized settings.)  
DRIVE EQ] is a preset equalizer that reduces noise outside the car or  
running noise of the tyres.  
/
/
TOP40  
/
POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/  
1
2
3
Press the volume knob to enter [FUNCTION].  
USER: Selects a preset equalizer suitable to the music  
Turn the volume knob to select [AUDIO CONTROL], then press the knob.  
Turn the volume knob to make a selection (see the following table),  
then press the knob.  
[
4
5
Repeat step 3 until the desired item is selected or activated.  
BASS BOOST  
LOUDNESS  
LV1 LV2 LV3 or LEVEL1  
bass boost level. ; OFF: Cancels.  
LV1 LV2 or LEVEL1 LEVEL2: Selects your preferred low and high  
/
/
/
LEVEL2/ LEVEL3: Selects your preferred  
Press and hold  
to exit.  
(or using RC-406)  
/
/
1
2
Press AUD to enter [AUDIO CONTROL].  
Press J/ Kto make a selection, then press  
frequencies boost to produce a well-balanced sound at a low volume  
level. ; OFF: Cancels.  
.
SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels.  
To return to the previous setting item, press  
.
LPF SUBWOOFER THROUGH: All signals are sent to the subwoofer. ; 85HZ 120HZ/  
/
Default: XX  
160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/  
160 Hz are sent to the subwoofer.  
SUB-W LEVEL –15 to +15  
(0)  
Adjusts the subwoofer output level.  
BASS LEVEL  
MID LEVEL  
TRE LEVEL  
EQ PRO  
–8 to +8  
–8 to +8  
–8 to +8  
(
(
(
+6  
)
Adjusts the level to memorize for each source. (Before  
making an adjustment, select the source you want to  
adjust.)  
SUB-W PHASE  
REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer  
output to be in line with the speaker output for optimum performance.  
(Selectable only if a setting other than [THROUGH] is selected for  
+5  
)
0)  
[LPF SUBWOOFER].)  
FADER  
R15 to F15  
(
0
): Adjusts the rear and front speaker output balance.  
): Adjusts the left and right speaker output balance.  
BASS ADJUST BASS CTR FRQ  
60  
Selects the center frequency.  
–8 to +8 +6): Adjusts the level.  
1.25 1.50 2.00: Adjusts the quality factor.  
ON: Turns on the extended bass. ; OFF: Cancels.  
0.5K 1.0K 1.5K 2.5K or 0.5KHZ 1.0KHZ 1.5KHZ  
2.5KHZ: Selects the center frequency.  
–8 to +8 +5): Adjusts the level.  
1.00 1.25: Adjusts the quality factor.  
10.0K 12.5K 15.0K 17.5K or 10.0KHZ 12.5KHZ  
15.0KHZ 17.5KHZ: Selects the center frequency.  
–8 to +8 ): Adjusts the level.  
/
80/ 100/ 200 or 60HZ/ 80HZ/ 100HZ/ 200HZ:  
BALANCE  
L15 to R15  
(
0
BASS LEVEL  
(
VOLUME OFFSET For AUX: –8 to +8  
(
0) ; For other sources: –8 to 0: Presets the volume  
adjustment level of each source. (Before adjustment, select the source  
you want to adjust.)  
BASS Q FACTOR 1.00  
/
/
/
BASS EXTEND  
SOUND RECNSTR ON: Creates realistic sound by compensating the high-frequency  
(Sound  
reconstruction)  
MID ADJUST MID CTR FRQ  
/
/
/
/
/
/
components and restoring the rise-time of the waveform that are lost  
in audio data compression. ; OFF: Cancels.  
MID LEVEL  
(
• [SUB-W LEVEL]/ [SUBWOOFER SET]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is  
selectable only if [SWITCH PREOUT] is set to [SUB-W] or [SUBWOOFER]. (  
• [SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if  
MID Q FACTOR 0.75  
/
/
4)  
TRE ADJUST TRE CTR FRQ  
/
/
/
/
/
/
[SUBWOOFER SET] is set to [ON].  
TRE LEVEL  
(0  
11  
ENGLISH  
DISPLAY SETTINGS  
TROUBLESHOOTING  
1
Press the volume knob to enter [FUNCTION].  
Turn the volume knob to select [DISPLAY], then press the  
knob.  
Symptom  
Sound cannot be heard.  
Remedy  
2
Adjust the volume to the optimum level.  
Check the cords and connections.  
3
4
5
Turn the volume knob to make a selection (see the following  
table), then press the knob.  
“MISWIRING CHECK WIRING  
THEN PWR ON” appears.  
“PROTECTING SEND SERVICE” Send the unit to the nearest service center.  
appears.  
Turn the power off, then check to be sure the terminals of the  
speaker wires are insulated properly. Turn the power on again.  
Repeat step 3 until the desired item is selected/activated or  
follow the instructions stated on the selected item.  
Press and hold  
to exit.  
To return to the previous setting item, press  
.
Sound cannot be heard.  
The unit does not turn on.  
Information shown on the  
display is incorrect.  
Clean the connectors. (  
2)  
Default: XX  
COLOR  
SELECT  
VARIABLE SCAN/  
preferred key and display illumination color.  
CUSTOM R/G/B/ preset colors*2: Selects your  
1
*
The unit does not work at all. Reset the unit. (  
3)  
You can create your own color (when [CUSTOM R/G/B] or preset  
Radio reception is poor.  
Static noise while listening  
to the radio.  
Connect the antenna firmly.  
Pull the antenna out all the way.  
colors*2 is selected). The color you have created can be stored in  
[
1
CUSTOM R/G/B].  
Press and hold the volume knob to enter the detailed color  
adjustment.  
Disc cannot be ejected.  
Press and hold  
the disc when it is ejected. If this does not solve the problem,  
reset the unit. (  
Mto forcibly eject the disc. Be careful not to drop  
2
Press  
S
/
T
to select the color (  
R
/
G
/
B) to adjust.  
3)  
3 Turn the volume knob to adjust the level (0 9), then press the  
knob.  
Noise is generated.  
Skip to another track or change the disc.  
Tracks do not play back as  
you intended them to play.  
Playback order is determined when files are recorded.  
DIMMER  
ON: Dims the display illumination (and button illumination*1). ;  
OFF: Cancels.  
“READING” keeps flashing.  
Elapsed playing time is not  
correct.  
Correct characters are not  
displayed (e.g. album name). limited number of symbols.  
“NA FILE”  
“NO DISC”  
“TOC ERROR”  
“PLEASE EJECT”  
Do not use too many hierarchical levels or folders.  
This is caused by how the tracks are recorded.  
BRIGHTNESS  
0
31: Selects your preferred brightness level for display  
illumination (and button illumination*1).  
TEXT SCROLL AUTO  
/
ONCE: Selects whether to scroll the display information  
This unit can only display uppercase letters, numbers, and a  
automatically, or scroll only once. ; OFF: Cancels.  
1
2
*
*
For  
Preset colors: RED1  
BLUE1 BLUE2 BLUE3  
AQUA2 GREEN1 GREEN2  
YELLOW ORANGE1 ORANGE2/  
/
.
Make sure the disc contains supported audio files. ( 14)  
Insert a playable disc into the loading slot.  
Make sure the disc is clean and inserted properly.  
Reset the unit. If this does not solve the problem, consult your  
nearest service center.  
/
RED2  
/
RED3  
/
PURPLE1  
/
PURPLE2  
LIGHTBLUE  
YELLOWGREEN1 YELLOWGREEN2  
ORANGERED  
/
PURPLE3  
/
PURPLE4/  
/
/
/
/
/
SKYBLUE1  
/
SKYBLUE2  
/
/
AQUA1  
/
/
GREEN3  
/
/
/
/
/
12  
TROUBLESHOOTING  
Symptom  
“READ ERROR”  
Remedy  
Symptom  
“ADD ERROR” /  
Remedy  
Copy the files and folders onto the USB device again. If this  
does not solve the problem, reset the USB device or use  
another USB device.  
Connect a USB device, and change the source to USB again.  
A copy-protected file is played.  
Connect a supported USB device, and check the connections.  
Connect a USB device that contains playable audio files.  
New station creation is unsuccessful.  
“SEARCH ERROR”  
“CHECK DEVICE”  
“NO SKIPS”  
Check the Pandora application on your device.  
The skip limit has been reached.  
No stations are found.  
“NO DEVICE”  
“COPY PRO”  
“NA DEVICE”  
“NO MUSIC”  
“iPod ERROR”  
“NO STATIONS”  
“STATION LIMIT”  
The number of registered stations has reached its limit.  
Retry after deleting unnecessary stations from your device.  
Reconnect the iPod.  
Reset the iPod.  
“CONNECT ERROR”  
“RATING ERROR”  
“LICENSE ERROR”  
Communication is unstable.  
Registration of thumbs up/thumbs down has failed.  
Sound cannot be heard  
during playback.  
Sound output only  
from the Android  
device.  
Reconnect the Android device.  
If in [HAND MODE], launch any media player application  
on the Android device and start playback.  
If in [HAND MODE], relaunch the current media player  
application or use another media player application.  
Restart the Android device.  
You try to access from a country which Pandora is not  
deliverable.  
iHeartRadio station  
cannot be selected.  
If “Explicit Content” in [Account Settings] is checked in the web  
version of iHeartRADIO, custom stations become unavailable.  
“CANNOT CREATE”  
“CANNOT SAVE”  
“DISCONNECTED”  
“NO SKIPS”  
Custom station name creation is unsuccessful.  
Addition to the favorite category failed.  
Check the connection to the device.  
The skip limit has been reached. Retry later.  
No stations are found.  
If this does not solve the problem, the connected Android  
device is unable to route the audio signal to unit. ( 14  
)
Cannot playback at  
BROWSE MODE].  
Make sure KENWOOD MUSIC PLAY APP is installed on the  
Android device. (  
Reconnect the Android device and make the appropriate  
setting in [ANDROID SETUP]. (  
If this does not solve the problem, the connected Android  
device does not support [BROWSE MODE]. ( 14  
[
8)  
“NO STATIONS”  
“NOT CONNECTED”  
“IHEARTLINK UP”  
8)  
Link to the application is impossible.  
)
Make sure you have installed the latest version of the  
iHeart Link for KENWOOD application on your device.  
“NO DEVICE” or  
“READING” keeps  
flashing.  
Switch off the developer options on the Android device.  
Reconnect the Android device.  
If this does not solve the problem, the connected Android  
“PLEASE LOGIN”  
You haven’t log in. Log in again.  
“STATION NOT AVAILABLE” Broadcast from the station is over.  
“STATION NOT SELECTED” No station is selected.  
device does not support [BROWSE MODE]. ( 14  
)
Playback is intermittent  
or sound skips.  
“ANDROID ERROR” /  
“NA DEVICE”  
Turn off the power saving mode on the Android device.  
“STREAM ERROR”  
“THUMB FAILED”  
“TIMED OUT”  
Broadcast data is interrupted.  
Registration of Thumbs Up/Down has failed.  
The request has resulted in time-out.  
Reconnect the Android device.  
Restart the Android device.  
13  
ENGLISH  
MORE INFORMATION  
General  
About iPod/iPhone  
Made for  
This unit can only play the following CDs:  
-
-
-
-
iPod touch (2nd, 3rd, 4th, and 5th generation)  
iPod classic  
iPod nano (3rd, 4th, 5th, 6th, and 7th generation)  
iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C  
You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.  
Detailed information and notes about the playable audio files are stated in an  
Playable files  
Playable audio file: MP3 (.mp3), WMA (.wma)  
Playable disc media: CD-R/CD-RW/CD-ROM  
Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.  
Playable USB device file system: FAT12, FAT16, FAT32  
About Android device  
This unit supports Android OS 4.1 and above.  
Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory (AOA) 2.0.  
If the Android device supports both mass storage class device and AOA 2.0, this unit always playback via  
AOA 2.0 as priority.  
Even when audio files comply with the standards listed above, playback may be  
impossible depending on the types or conditions of media or device.  
Unplayable discs  
About Pandora  
Discs that are not round.  
Pandora is available only in the U.S., Australia and New Zealand.  
Discs with coloring on the recording surface or discs that are dirty.  
Recordable/ReWritable discs that have not been finalized.  
8 cm CD. Attempting to insert using an adapter may cause malfunction.  
Because Pandora is a third-party service, the specifications are subject to change without prior notice.  
Accordingly, compatibility may be impaired, or some or all of the services may become unavailable.  
Some functions of Pandora cannot be operated from this unit.  
For issues using the application, please contact Pandora at [email protected].  
About USB devices  
This unit can play MP3/WMA/WAV files stored on a USB mass storage class device.  
You cannot connect a USB device via a USB hub.  
Connecting a cable whose total length is longer than 5 m may result in abnormal  
playback.  
This unit cannot recognize a USB device whose rating is other than 5 V and  
exceeds 1 A.  
About KENWOOD Music Editor Light and KENWOOD Music Control  
Muting upon the reception of a phone call  
This unit supports the PC application KENWOOD Music Editor Light and Android™  
application KENWOOD Music Control.  
When you play audio files with song data added using the KENWOOD Music Editor  
Light or KENWOOD Music Control, you can search for audio files by Genres, Artists,  
Albums, Playlists, and Songs.  
Connect the MUTE wire to your telephone using a commercial telephone  
accessory. ( 17  
)
When a call comes in, “CALL” appears. (The audio system pauses.)  
• To continue listening to the audio system during a call, press  
disappears and the audio system resumes.  
. “CALL”  
KENWOOD Music Editor Light and KENWOOD Music Control are available on the  
When the call ends, “CALL” disappears. (The audio system resumes.)  
14  
SPECIFICATIONS  
FM Frequency Range  
USB Standard  
File System  
USB 1.1, USB 2.0  
/
/
/
:
FAT12/ 16/ 32  
87.9 MHz — 107.9 MHz (200 kHz space)  
Maximum Supply Current  
MP3 Decode  
DC 5 V 1 A  
/
:
87.5 MHz — 108.0 MHz (50 kHz space)  
Compliant with MPEG-1/2 Audio Layer-3  
Compliant with Windows Media Audio  
Linear-PCM  
Usable Sensitivity (S/N = 26 dB)  
8.2 dBf (0.71 μV/75 Ω)  
WMA Decode  
Quieting Sensitivity  
(DIN S/N = 46 dB)  
17.2 dBf (2.0 μV/75 Ω)  
WAV Decode  
Maximum Output Power  
Full Bandwidth Power  
Speaker Impedance  
Tone Action  
50 W × 4  
Frequency Response ( 3 dB)  
Signal-to-Noise Ratio (MONO)  
Stereo Separation (1 kHz)  
30 Hz — 15 kHz  
22 W × 4 (at less than 1 % THD)  
4 Ω — 8 Ω  
64 dB  
40 dB  
Bass  
200 Hz 8 dB  
2.5 kHz 8 dB  
12.5 kHz 8 dB  
AM Frequency Range  
530 kHz — 1 700 kHz (10 kHz space)  
29 dBμ (28.2 μV)  
Middle  
Usable Sensitivity (S/N = 20 dB)  
Treble  
Laser Diode  
GaAIAs  
Preout Level/Load (CD)  
Preout Impedance  
2 500 mV/10 kΩ  
≤ 600 Ω  
Digital Filter (D/A)  
Spindle Speed  
8 times over sampling  
500 rpm — 200 rpm (CLV)  
Frequency Response ( 3 dB)  
Input Maximum Voltage  
Input Impedance  
20 Hz — 20 kHz  
1 000 mV  
Wow & Flutter  
Below measurable limit  
Frequency Response ( 1 dB)  
Total Harmonic Distortion (1 kHz)  
Signal-to-Noise Ratio (1 kHz)  
Dynamic Range  
20 Hz — 20 kHz  
30 kΩ  
0.01 %  
105 dB  
Operating Voltage  
14.4 V (10.5 V — 16 V allowable)  
90 dB  
Maximum Current Consumption  
Operational Temperature Range  
Installation Size (W × H × D)  
10 A  
Channel Separation  
MP3 Decode  
85 dB  
0°C — +40°C  
Compliant with MPEG-1/2 Audio Layer-3  
Compliant with Windows Media Audio  
182 mm × 53 mm × 159 mm  
(7-3/16" × 2-1/16" × 6-1/4")  
WMA Decode  
Weight  
1.2 kg (2.65 lbs)  
Subject to change without notice.  
15  
ENGLISH  
Warning  
Installing the unit (in-dash mounting)  
The unit can only be used with a 12 V DC power supply, negative  
ground.  
Disconnect the battery’s negative terminal before wiring and  
mounting.  
Do not connect Battery wire (yellow) and Ignition wire (red) to the  
car chassis or Ground wire (black) to prevent a short circuit.  
Insulate unconnected wires with vinyl tape to prevent a short circuit.  
Be sure to ground this unit to the car’s chassis again after  
installation.  
Do the required wiring.  
17  
(
)
Hook on the top side  
Caution  
For safety’s sake, leave wiring and mounting to professionals.  
Consult the car audio dealer.  
Dashboard of  
your car  
Orientate the trim plate as  
illustrated before fitting.  
Install this unit in the console of your vehicle. Do not touch the  
metal parts of this unit during and shortly after use of the unit.  
Metal parts such as the heat sink and enclosure become hot.  
Do not connect the  
wire (black), or connect them in parallel.  
[wires of speakers to the car chassis or Ground  
Bend the appropriate tabs to hold the  
mounting sleeve firmly in place.  
Mount the unit at an angle of less than 30º.  
If your vehicle wiring harness does not have the ignition terminal,  
connect Ignition wire (red) to the terminal on the vehicle’s fuse box  
which provides 12 V DC power supply and is turned on and off by  
the ignition key.  
Keep all cables away from heat dissipate metal parts.  
After the unit is installed, check whether the brake lamps, blinkers,  
wipers, etc. on the car are working properly.  
When installing without the mounting sleeve  
1
Remove the mounting sleeve and trim plate from  
the unit.  
2
Align the holes in the unit (on both sides) with the  
vehicle mounting bracket and secure the unit with  
screws (commercially available).  
Use only the specified screws. Using wrong screws might damage the unit.  
If the fuse blows, first make sure the wires are not touching car’s  
chassis, then replace the old fuse with one that has the same rating.  
How to remove the unit  
Basic procedure  
1
2
Detach the faceplate.  
1
2
3
Remove the key from the ignition switch, then  
disconnect the [terminal of the car battery.  
Connect the wires properly.  
Fit the catch pin on the extraction keys into  
the holes on both sides of the trim plate,  
then pull it out.  
See Wiring connection. ( 17  
)
3
Insert the extraction keys deeply into the  
slots on each side, then follow the arrows  
as shown on the right.  
Install the unit to your car.  
See Installing the unit (in-dash mounting).  
4
5
Connect the [terminal of the car battery.  
Reset the unit. (  
3)  
16  
Wiring connection  
Part list for installation  
/
/
:
/
/
:
(A) Faceplate  
Front output  
Rear/ subwoofer output  
Rear/ subwoofer output  
Antenna terminal  
Fuse (10 A)  
(B) Trim plate  
White  
If no connections are made, do not let the wire come out from the tab.  
To front speaker (left)  
To front speaker (right)  
To rear speaker (left)  
White/Black  
(C) Mounting sleeve  
Gray  
Brown  
To the terminal that is grounded when the  
telephone rings or during conversation  
(Mute control wire)  
Gray/Black  
(
14)  
Green  
(To connect the Kenwood navigation system,  
refer your navigation manual.)  
Green/Black  
Purple  
(D) Wiring harness  
To the power control terminal when using  
the optional power amplifier or to the  
antenna control terminal in the vehicle  
Blue/White  
To rear speaker (right)  
Ignition switch  
Purple/Black  
(Power control wire/  
Antenna control wire)  
Car fuse box  
Red  
(Ignition wire)  
(E) Extraction key  
Yellow  
Light blue/yellow  
To the steering wheel remote control  
adapter  
(Battery wire)  
Black (Ground wire)  
(Steering remote  
control wire)  
Car fuse box  
To the metallic body or chassis of the car  
Battery  
17  
ENGLISH  
CAUTION  
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to  
connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to  
meet Apple performance standards. Apple is not responsible for the operation of this device or  
its compliance with safety and regulatory standards. Please note that the use of this accessory  
with iPod or iPhone may affect wireless performance.  
Use of controls or adjustments or performance of procedures other than those specified herein may  
result in hazardous radiation exposure.  
In compliance with Federal Regulations, following are reproductions of labels on, or inside the  
product relating to laser product safety.  
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in  
the U.S. and other countries.  
• Lightning is a trademark of Apple Inc.  
• Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered  
trademarks of Pandora Media, Inc., used with permission.  
• iHeartRadio® is a registered mark of Clear Channel Broadcasting, Inc. in the United States and  
other countries. Such marks are used under license.  
JVC KENWOOD Corporation  
2967-3, ISHIKAWA-MACHI,  
HACHIOJI-SHI, TOKYO, JAPAN  
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR  
SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.  
• Android is trademark of Google Inc.  
Location : Top Plate  
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de  
la vida útil (aplicable a los países que hayan adoptado sistemas independientes de  
recogida de residuos)  
FCC WARNING  
This equipment may generate or use radio frequency energy. Changes or modifications to this  
equipment may cause harmful interference unless the modifications are expressly approved in the  
instruction manual. The user could lose the authority to operate this equipment if an unauthorized  
change or modification is made.  
Los productos con el símbolo de un contenedor con ruedas tachado no podrán  
ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos  
al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar  
el tratamiento adecuado a estos productos y a sus subproductos residuales  
correspondientes. Póngase en contacto con su administración local para obtener  
información sobre el punto de recogida más cercano. Un tratamiento correcto  
del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al  
mismo tiempo efectos perjudiciales en la salud y el medio ambiente.  
FCC NOTE  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equipment may cause harmful  
interference to radio communications, if it is not installed and used in accordance with the  
instructions. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and on, the user is encouraged to try to  
correct the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
Informação sobre a eliminação de pilhas  
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao  
revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.  
A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos  
naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
CALIFORNIA, USA ONLY  
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special  

Samsung Clx 6220fx User Manual
Philips Scb1225nb User Manual
NEC NP PA722X 02 User Manual
MAKITA HR002G User Manual
LG 24TQ510S User Manual
LEXMARK X1150 User Manual
Lanier 5635 User Manual
CRAFTSMAN 358.341151 User Manual
CRAFTSMAN 315.SS630 User Manual
BLACK DECKER LEDUC9 5WK User Manual