000 000
Gazebo II Plus
52 in Ceiling Fan
Owner’s Manual
Gazebo II Plus
Ventilador de Techo de 1,32 m
Manual del Propietario
®
Gazebo II Plus by Hampton Bay
Thank you for purchasing our ceiling fan. This product has been
manufactured with the highest standards of safety and quality.
The finish of this fan is weather resistant, but over time will
naturally weather and fade.
52” Gazebo II Plus
Ceiling Fan by Hampton Bay
Date Purchased
Table of Contents
Safety Rules . . . . . . . . . . . . . . . . . . . . 1
Unpacking Your Fan . . . . . . . . . . . . . . 2
Installing Your Fan . . . . . . . . . . . . . . . 3
Installing the Light Kit . . . . . . . . . 11
Operating Your Fan . . . . . . . . . . . . . . 12
Care of Your Fan . . . . . . . . . . . . . . . . 13
Troubleshooting . . . . . . . . . . . . . . . . . 13
Specifications . . . . . . . . . . . . . . . . . . 14
Warranty Information . . . . . . . . . . . . 15
Store Purchased
000-000
UL Model No.
Serial No.
11289
Vendor No.
792145353669
UPC
Unpacking Your Fan
Unpack your fan and check the contents. You should have the following items:
A
B
2
6
9
3
1
7
8
4
C
10
11
5
Set of blades (5)
Light fixture
Glass shade
Blade attachment hardware
1.
2.
3.
4.
5.
6.
7.
A.
B.
C.
(16 screws with rubber washers)
Canopy assembly
Ball/downrod assembly
Coupling cover
Fan motor assembly
Set of blades arms (5)
8.
Pull chains and fobs (2)
9.
Electrical hardware
(3 plastic wire nuts)
13 Watt compact fluorescent bulbs (2)
Extra plastic plug
10.
11.
Balance kit
WARNING
DO NOT INSTALL OR USE FAN IF ANY
PART IS DAMAGED OR MISSING.
CALL TOLL FREE 1-877-898-1881.
2
Provide Strong
Support
Installing Your Fan
Figures 1~3 are examples of different ways to
mount the outlet box.
Tools Required
Phillips screwdriver, straight slot screwdriver, step
ladder and wire cutters.
Recessed
Outlet Box
Ceiling
Mounting
Plate
Figure 3
Mounting Options
Outlet Box
Note: You may need a longer downrod to
maintain proper blade clearance when installing
on a steep, sloped ceiling. The maximum angle
If there isn't an existing UL listed mounting box,
then read the following instructions. Disconnect
the power by removing fuses or turning off circuit
breakers.
°
allowable is 20 . If the canopy touches downrod,
remove the decorative canopy bottom cover and
Figure 1
°
turn the canopy 180 before attaching the canopy
Secure the outlet box directly to the building
structure. Use appropriate fasteners and building
materials. The outlet box and its support must be
able to fully support the moving weight of the fan
(at least 35 lbs). Do not use plastic outlet boxes.
to the mounting plate.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT FAN
ONLY TO AN OULET BOX MARKED ACCEPT-
ABLE FOR FAN SUPPORT AND USE THE
MOUNTING SCREWS PROVIDED WITH THE
OULET BOX. OUTLET BOX COMMONLY USED
FOR THE SUPPORT OF LIGHTING FIXTURE
MAY NOT BE ACCEPTABLE FOR FAN SUPPORT
AND MAY NEED TO BE REPLACED. CONSULT A
QUALIFIED ELECTRICIAN IF IN DOUBT.
Outlet Box
Figure 4
Outlet Box
To hang your fan where there is an existing fixture
but no ceiling joist, you may need an installation
hanger bar as shown in Figure 4 (available at any
Home Depot retailer).
Figure 2
3
Motor Wires
Remove the
Pin in Locked
Positioon
Hanging the Fan
Canopy Ring
Ball/Downrod
Assembly
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly.
Ceiling Canopy
Canopy Ring
NOTE: This ceiling fan is supplied with two types
of hanging assemblies; the standard ceiling
installation using the downrod with ball and socket
mounting, and the "close-to-ceiling" mounting.
The "close-to-ceiling" mounting is recommended
in rooms with less than 8-foot ceilings or in areas
where additional space is desired from the floor to
the fan blades.
Coupling Cover
Clevis Pin
Cotter Pin
Figure 5
Remove the mounting bracket from the canopy
by loosening the four screws on the top of the
canopy. Remove the two non-slotted screws
and loosen the slotted screws (Figure 6).
2.
Motor Collar
Tighten Screw
Firmly
When using the standard downrod installation, the
distance from the ceiling to the bottom of the fan
blades will be approximately 12 inches. The
"close-to-ceiling" installation reduces the distance
from the ceiling to the bottom of the fan blades to
approximately 9 inches.
Figure 7
Loosen but
Remove
Align the holes at the bottom of the downrod
with the holes in the coupling on top of the
motor housing (Figure 7). Carefully insert the
clevis pin through the holes in the collar and
downrod. Be careful not to jam the clevis pin
against the wiring inside the downrod. Insert
the cotter pin through the hole near the end of
the clevis pin until it snaps into its locked
position, as noted in the circle inset of Fig. 7.
5.
6.
do not Remove
Once you have decided which ceiling installation
you will use, proceed with the following
instructions. Where necessary, each section of the
instructions will note the different procedures to
follow for the two types of installation.
Figure 6
Route wires exiting from the top of the fan motor
through the coupling cover and canopy ring.
Make sure the slot openings are on top. Route the
wires through the canopy and then through the
ball/downrod assembly (Figure. 7).
3.
4.
Tighten two set screws on top of the fan motor
firmly. (Figure 7)
Option 1:
WARNING
FAILURE TO PROPERLY INSTALL COTTER
PIN AS NOTED IN STEP 5 COULD RESULT IN
FAN LOOSENING AND POSSIBLY FALLING.
Standard Ceiling Mounting
Remove the canopy ring from the canopy.
(Figure 5).
1.
Loosen, but do not remove the 2 set screws on
the collar on top of the motor housing.
4
NOTE: If a longer downrod is needed, take out
the screw located in the hanger ball, lower the
hanger ball and remove the pin, remove all 3
pieces from the downrod and assemble them onto
the new longer downrod before proceeding step 3.
(The longer downrod is available at any Home
Depot store)
Remove the decorative canopy bottom cover
from the canopy by turning the canopy bottom
cover counterclockwise (Figure 8).
Motor
Collar
3.
4.
Screw and Lock Washer
(3 of 6 Places)
Remove three of the six screws and lock
washers (every other one) from the collar of
top motor. (Figure 9).
Route the wires exiting the top of the fan motor
through the canopy ring (make sure the slot
openings are on top), then proceed to place the
ceiling canopy over the collar at the top of the
motor. (Figure 10)
5.
Option 2:
Close-to-Ceiling Mounting
Figure 9
Remove the canopy ring from the canopy.
(Figure 5).
1.
Screw and
Lock Washer
(3 Places)
Collar
Align the mounting holes with the holes in the
motor and fasten using the screws and lock
washers removed in step 4 (Fig. 10).
6.
7.
Remove the mounting bracket from the canopy
by loosening the four screws on the top of the
canopy. Remove the two non-slotted screws
and loosen the slotted screws (Figure 6).
2.
Ceiling
Canopy
Tighten the mounting screws security.
Canopy Ring
WARNING
FAILURE TO COMPLETELY TIGHTEN THE
THREE SCREWS IN STEP 7 COULD RESULT IN
FAN LOOSENING AND POSSIBLY FALLING.
Figure 10
Canopy
Bottom
Cover
Remove
Figure 8
5
UL Listed Outlet Box
Installing Fan to
the Electrical Box
WARNING
Tab
120V
Wires
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR OTHER PERSONAL INJURY.
MOUNT FAN ONLY TO AN OUTLET BOX OR
SUPPORTING SYSTEM MARKED ACCEPTABLE
FOR FAN SUPPORT AND USE THE MOUNTING
SCREWS PROVIDED WITH THE OUTLET BOX.
Groove
Ceiling Mounting
Bracket
Tab
Pass the 120-volt supply wires through the
center hole in the ceiling mounting bracket as
shown in Figure 11.
1.
Mounting
Standard Mounting Close-to-Ceiling Mounting
Screws (Supplied
with Outlet Box)
Figure 12
Figure 11
Install the ceiling mounting bracket on the
outlet box with the screws and washers
provided with your outlet box (Figure 11).
When using “close-to-ceiling” mounting, it is
important that the mounting bracket be level. If
necessary, use leveling washers (not included)
between the mounting bracket and the outlet
box. Note that the flat side of the mounting
bracket is toward the outlet box. (Figure 11)
2.
WARNING
Carefully lift the fan assembly up to the ceiling
mounting bracket and hang the fan on the tab
provided by utilizing one of the holes at the
outer rim of the ceiling canopy (Figure 12). If
use standard mounting, seat the hanger ball in
the mounting bracket socket. Make sure the tab
on the mounting bracket socket is properly
seated in the groove in the hanger ball (Figure
12).
4.
THE TAB AS SHOWN IN FIGURE 12 IS ONLY TO
BALANCE THE FAN WHILE ATTACHING
WIRING. FAILURE TO HANG AS SHOWN IN
FIGURE 12 MAY RESULT IN TAB BREAKING
CAUSING THE FAN TO FALL. TAB MUST PASS
FROM INSIDE TO OUTSIDE OF CANOPY.
Security tighten the two mounting screws.
3.
WARNING
WHEN USING THE STANDARD BALL/ DOWN-
ROD MOUNTING. THE TAB IN THE RING MUST
REST IN THE GROOVE OF THE HANGER BALL.
FAILURE TO PROPERLY SEAT THE TAB IN
THE GROOVE COULD CAUSE DAMAGE TO
WIRING.
6
Connect the fan motor black wire to the supply
black (hot) wire using a wire nut (Figure 13).
3.
4.
5.
SUPPLY CIRCUIT
Making the Electrical
Connections
Connect the blue wire for light kit to the black
household supply wire.
Ground
Conductor
REMEMBER to disconnect the power.
Turn wire nut connections upward, spreading
them apart so the green (ground) will be on one
side of the outlet box and the white, black and
blue wire will be on the other side, and push
carefully up into the outlet box.
If you feel you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
Outlet Box
Green
Ground
Lead
Follow the steps below to connect the fan to your
household wiring. Use the wire nuts supplied with
your fan. Secure the wire nuts with electrical tape.
Make sure there are no loose strands or
connections.
WARNING
Ground to
Downrod
CHECK TO SEE THAT ALL CONNECTIONS ARE
TIGHT, INCLUDING GROUND, AND THAT NO
BARE WIRE IS VISIBLE AT THE WIRE NUTS.
EXCEPT FOR THE GROUND WIRE.
Connect the ground cnductor of the 120V
supply (this may be a bare wire or a wire with
green colored insulation) to the green ground
lead(s) of the fan (Figure 13). When using
standard ceiling mounting, there are two green
grounding leads; one from the ceiling mount-
ing bracket and one from the ball/downrod
assembly. When using “Close-to-Ceiling”
mounting, there is only one green ground lead
from the ceiling mounting bracket since the
ball/downrod assembly is not used.
1.
WARNING
ELECTRICAL DIAGRAMS ARE FOR REFER-
ENCE ONLY. OPTIONAL USE OF ANY LIGHT
KIT SHALL BE UL LISTED AND MARKED
SUITABLE FOR USE WITH THIS FAN.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK. DO NOT USE THIS FAN WITH ANY
SOLID-STATE SPEED CONTROL DEVICE.
Connect the fan motor white wire to the supply
white (neutral) wire using a wire nut. (Figure
13)
2.
Figure 13
7
Close-to-Ceiling Mounting
Finishing the Fan
Installation
Outlet Box
Remove the fan from the tab on the hanger
bracket. Secure the canopy to the hanger bracket
with four screws included with your fan. (Fig. 15)
Raise up canopy ring and line up the 4 tabs with
the 4 grooves on the canopy. Once lined up, slide
the canopy ring and secure it to the canopy until
snug.
Standard Ceiling Mounting
WARNING
Hanger
Bracket
Screws
Canopy
LOCKING SLOTS OF CEILING CANOPY ARE
PROVIDED ONLY AS AN AID TO MOUNTING.
DO NOT LEAVE FAN ASSEMBLY UNATTENDED
UNTIL ALL FOUR CANOPY SCREWS ARE
ENGAGED AND FIRMLY TIGHTENED.
Canopy
Ring
Outlet Box
Hanger
Slide canopy up to the ceiling as shown in Figure
14. Make sure you place the wires safely into the
outlet box. Secure the canopy to the hanger
bracket with the four screws with your fan. Raise
up canopy ring and line up the 4 tabs with the 4
grooves on the canopy. Once lined up, slide the
canopy ring and secure it to the canopy until snug.
Screws
Bracket
Figure 15
Groove
Canopy
WARNING
Canopy
Ring
Tab
MAKE SURE THE TAB ON THE HANGER
BRACKET PROPERLY SITS IN THE GROOVE IN
THE HANGER BALL BEFORE ATTACHING THE
CANOPY TO THE BRACKET BY TURNING THE
HOUSING UNTIL IT DROPS INTO PLACE.
Figure 14
8
Attaching the Fan Blades
Motor
Tab
NOTE
MOTOR IS SHIPPED WITH RUBBER MOTOR STOPS
TO PREVENT MOVEMENT DURING TRANSPORTA-
TION. REMOVE MOTOR STOPS PRIOR TO ATTACH-
ING BLADE BRACKETS. (FIG. 16)
Blade arm
Slot
Step 1. Attach blades to blade arms using three
screws with rubber washers. (Fig. 17) Start a
screw into the blade arm, do not tighten. Repeat
for the 2 remaining screws and washers.
Rubber packing mounts
Screws
Figure 16
Step 2. Tighten each screw securely starting with
the center screw. Make sure the blade is straight.
Repeat steps for the remaining blades.
Screws with
Rubber Washers
Figure 18
Step 3. Fasten the blade assemblies to the motor
housing by lining up the slots of the blade arms
with the tabs on the motor housing, then tighten
the two screws and washers already installed in the
blade arms. (Fig. 18)
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY,
DO NOT BEND THE BLADE ARMS WHILE
INSTALLING, BALANCING THE BLADES, OR
CLEANING THE FAN. DO NO INSERT FOREIGN
OBJECTS BETWEEN ROTATING FAN BLADES.
Blade
Blade Arm
Figure 17
9
Blade Balancing
The following procedure should correct most fan wobble. Check after each
step.
Touching Ceiling
Check that all blade and blade arm screws are secure.
1.
2.
Most fan wobble problems are caused when blade levels are unequal.
Check this level by selecting a point on the ceiling above the tip of one of
the blades. Measure from a point on the center of each blade to the point
on the ceiling. Measure this distance as shown in Figure 19. Rotate the fan
until the next blade is positioned for measurement. Repeat for each blade.
Measurements deviation should be within 1/8˝. Run the fan for 10
Minutes.
Use the enclosed Blade Balancing Kit if the blade wobble is still
noticeable.
3.
Figure 19
10
NOTE
Fan without Light Kit
Installing the Light
LIGHT BULBS HAVE NO WARRANTY; CAN BE
PURCHASED AT ANY HOME DEPOT RETAILER.
(Optional)
Kit
Disassemble the switch housing cover from the
light kit, you can keep the light kit for future
use.
1.
NOTE
BEFORE STARTING INSTALLATION, DISCONNECT
THE POWER BY TURNING OFF THE CIRCUIT
BREAKER OR REMOVING THE FUSE AT FUSE
BOX. TURNING POWER OFF USING THE FAN
SWITCH IS NOT SUFFICIENT TO PREVENT
ELECTRIC SHOCK.
Attach the plastic plug to the switch housing.
(Fig. 21)
2.
3.
Install the switch housing cover to the switch
housing with screws provided.
While holding the light kit assembly under your
fan, locate two single white and blue wires in
the switch housing labeled FOR LIGHT. Make
the polarized plug connections:
- White to white
1.
2.
- Blue to black
Reverse
switch
Switch
Carefully push all wires back into the switch
housing. Attach the light kit fitter by aligning its
keyhole slots with the three screws holes and
reversing switch on the side of switch housing.
Tighten the three screws securely to prevent the
light kit from vibrating loose.(Fig. 20)
housing
Wire
Screws
connector
Pull chains
Pass the two pull chains on the switch housing
through the chain holders located on the light
fitter, install the fobs to the pull chains. (Fig. 20)
3.
4.
5.
6.
Bulbs
Chain holders
Switch
Install 2 x 13 watts compact fluorescent bulbs
(included) into the light kit sockets. NOTE:
CFL bulbs are NOT dimmable.
Housing
Screws
Switch
Housing
Cover
Raise glass shade up against the light kit and
secure it to fan by turning glass clockwise until
snug. DO NOT OVERTIGHTEN. (Fig. 20)
Glass shade
Figure 20
Plastic Plug
Restore power and your light kit is ready for
operation.
Figure1211
Operating Your Fan
WARNING
LOCKING SLOTS OF CEILING CANOPY ARE
Warm weather - (Counter Clockwise Direction)
PROVIDED ONLY AS AN AID TO MOUNTING.
DO NOT LEAVE FAN ASSEMBLY UNATTENDED
UNTIL ALL FOUR CANOPY SCREWS ARE
ENGAGED AND FIRMLY TIGHTENED.
A downward air flow creates a cooling effect as
shown in Figure 22. This allows you to set your air
conditioner on a higher setting without affecting
your comfort.
NOTE
WAIT FOR FAN TO STOP BEFORE REVERSING
THE DIRECTION OF THE BLADE ROTATION.
Turn on the power and check the operation of the
fan. The pull chain controls the fan speed as
Figure 22
follows:
1 pull - High
2 pulls - Medium
3 pulls - Low
4 pulls - Off.
Cool weather - (Clockwise Direction) An upward
air flow moves warm air off the ceiling are as
shown in Figure 23. This allows you to set your
heating unit on a lower setting without affecting
your comfort.
Light kit pull chain- it controls the light kit in
"ON" or "OFF".
Speed settings for warm or cool weather depend
on factors such as the room size, ceiling height,
number of fans, and so on.
The slide switch controls directions: forward
(switch down) or reverse (switch up).
Figure 23
12
Care of Your Fan Troubleshooting
Here are some suggestions to help you maintain
your fan.
PROBLEM
SOLUTION
Fan will not start
Check main and branch circuit fuses or breakers.
Check line wire connections to the fan and switch wire
connections in the switch housing.
1.
2.
Because of the fan's natural movement, some
1.
connections may become loose. Check the
support connections, brackets, and blade
attachments twice a year. Make sure they are
secure. (It is not necessary to remove fan from
ceiling.)
Fan sounds noisy
Make sure all motor housing screws are snug.
Make sure the screws that attach the fan blade bracket to the
motor hub is tight.
1.
2.
Clean your fan periodically to help maintain its
new appearance over the years. Do not use
water when cleaning. Use only a soft brush or
lint-free cloth to avoid scratching the finish.
The plating is sealed with a lacquer to
minimize discoloration or tarnishing. Do not
use water when cleaning. This could damage
the motor, or the wood, or possibly cause an
electrical shock.
2.
Make sure wire nut connections are not rattling against each
other or the interior wall of the switch housing.
3.
4.
5.
Allow
a
24-hour "breaking-in" period. Most noises
associated with a new fan disappear during this time.
If using the ceiling light kit, make sure the screws securing
the glassware are tight.
Check that the light bulb is also secure.
Make sure there is a short distance from the ceiling to the
canopy. It should not touch the ceiling.
Make sure your ceiling box is secure and rubber isolator
pads are used between mounting bracket and outlet box.
6.
7.
You can apply a light coat of furniture polish to
the wood blades for additional protection and
enhanced beauty. Cover small scratches with a
light application of shoe polish.
3.
4.
WARNING
MAKE SURE THE POWER IS OFF AT THE ELECTRICAL
PANEL BOX BEFORE YOU ATTEMPY ANY REPAIRS.
REFER TO THE SECTION, “MAKING ELECTRICAL
CONNECTIONS”.
There is no need to oil your fan. The motor has
permanently lubricated sealed ball bearings.
13
Specifications
FAN SIZE SPEED VOLTS AMPS WATTS RPM
CFM
N.W.
G.W.
C.F.
LOW
MED.
HIGH
0.21
0.38
0.53
11
32
66
64
1583
3587
5448
10.6 kgs
(23.4 lbs)
12.3 kgs
(27.1 lbs)
52”
120
2.27'
110
158
These are approximate measures. They do not include Amps and Wattage used by the light kit .
14
Lifetime Limited Warranty
(lifetime warranty on motor)
The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time
of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.
Hampton Bay also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from
defects in workmanship and material at the time of shipment from the factory for a period of one year after the
date of purchase by the original purchaser. We agree to correct such defects without charge or at our option
replace with a comparable or superior model if the product is returned to Hampton Bay. To obtain warranty
service, you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the
product are your responsibility. Damage to any part such as by accident or misuse or improper installation or
by affixing any accessories, is not covered by this warranty. Because of varying climatic conditions this
warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling.
Brass finishes of this type give their longest useful life when protected from varying weather conditions. A
certain amount of “wobble” is normal and should not be considered a defect. Servicing performed by
unauthorized persons shall render the warranty invalid. There is no other express warranty. Hampton Bay
hereby disclaims any and all warranties, including but not limited to. Those of merchantability and fitness for
a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be
disclaimed is limited to the time period as specified in the express warranty. Some states do not allow
limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The retailer
shall not be liable for incidental, consequential, or special damages arising out of or in connection with product
use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of
incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty
gives specific legal rights, and you may also have other rights which vary from state to state. This warranty
supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must
be paid by the customer.
You must present a copy of the original
purchase receipt to obtain warranty
service.
Ceiling Fan Parts & Service Department
16040 North 59th Avenue
Glendale, AZ 85306-2350
Attach receipt here for easy
location
15
|