R
HP DesignJet 700 Plotter
HP DesignJet 750C Plus Plotter
User’s Guide
Warranty Statement
Warranty Limitations
After the Warranty
Period
About This Edition
OneĆYear OnĆSite
Hardware Warranty
HP makes no other
warranty, either
expressed or implied,
with respect to this
product. HP specifically solving sections in this
Edition dates are as
follows:
If your hardware should
fail after the warranty
period, read the problem
Except when purchased
as part of
1st edition,
September 1996
a
system,
disclaims the implied
warranties of
guide, then contact an
Authorized HP Personal
Computer Dealer Repair
HewlettĆPackard warrants
your graphics peripheral
hardware product against
New editions are
merchantability and
complete revisions of the
particular Center or call an HP
manual. Change sheets,
fitness for
a
defects in materials and
workmanship for
purpose. Some states orSales and Support Office
a
period
which may be issued
between editions, contain
provinces do not allow for details of the services
of one year from receipt
limitations on the
by the end user (proof of
available. If you have an
additional information.
duration of an implied HP Maintenance
purchase required). If HP
The dates on the title
page change only when
new edition is published.
Minor corrections that do
not affect the function of
the product may be made
warranty, so the above Agreement, request
receives notice of such
defects during the
a
limitation or exclusion service under your
may not apply to you.agreement.
However, any implied
warranty period, HP will
either, at its option,
warranty of
repair or replace products
merchantability or fitness
is limited to the oneĆyear
duration of this written
warranty.
that prove to be
defective.
at reprint without
change to the print date.
a
Should HP be unable to
repair or replace the
Many product updates
and fixes do not require
changes to this User's
Guide and, conversely,
User's Guide
improvements may be
done without
accompanying product
changes. Therefore, do
This warranty gives you
specific legal rights, and
you may also have other
rights which may vary
product within
a
reasonable amount of
time, the customer's
alternative exclusive
from state to state, or
remedy shall be refund of
province to province.
the purchase price upon
return of the product.
Obtaining Service During
Warranty Period
If your hardware should
not expect
a
one to one
If this product was
ratio between product
updates and User's Guide
revisions.
purchased as part of an
fail during the warranty
period, read the
HP system in
coordinated shipment or
a
Troubleshooting"
as
a
system addĆon, it is
section in this guide, then
contact your local
warranted against defects
in material and
HewlettĆPackard Sales
workmanship during the
same period as the HP
system.
and Support Office or an
Authorized HP Personal
Computer Dealer Repair
Center and arrange for
Exclusions
onĆsite repair of the
The above warranty shall
product. Retain proof of
purchase in order to
obtain warranty service.
not apply to defects
resulting from: improper
or inadequate
maintenance by
customer;
If
a
prompted by the
service call is
customerĆsupplied
software or interfacing;
unauthorized
modification or misuse;
operation outside of the
environmental
"Maintenance advised"
message (see page 8Ć3), it
is not covered under this
warranty.
specifications for the
product; operation of
nonĆsupported media;
improper site preparation
and maintenance;
usage exceeding the
product warranty limits
(see page 8Ć3).
HP Customer
Support
in the
USA
Phone
(208) 323 2551
For support details, see the section “Getting help” in chapter 9.
HP DesignJet 700 / 750C Plus Plotter User’s Guide
C4705-90031 English
User’s Guide
HP DesignJet 700 Plotter
HP DesignJet 750C Plus Plotter
C4705A, C4706A, C4708A and C4709A
ii
Finding Information
This User’s Guide for the HP DesignJet 700 and 750C Plus plotters contains the
following types of information:
Set Up
Use
Maintenance
Troubleshooting
Reference Material.
To help find specific information, a comprehensive table of contents is provided at
the front and an alphabetical index is provided at the back.
You will notice the use of symbols in the left margin and shaded backgrounds to
the text. These are used to identify different types of information as follows:
Information specific only to the HP DesignJet 700 is shown like this.
Information specific only to the HP DesignJet 750C Plus is shown like this.
All other information is applicable to both plotters.
700
750C Plus
The Quick Reference Guide Contains:
Some information that you are most likely to need on a day-to-day basis, for
example, the front-panel menu structure and media-type selections. It is stored
in the pocket at the back of the plotter.
iii
Where To Find the Most Commonly Needed Information
To find how to ...
go to ...
Install the plotter
chapter 1
"
"
"
"
"
"
"
"
"
"
Connect the plotter
page 1-27
page 3-2
Choose media
Load media
page 3-10
page 3-26
pages 7-2 and 7-3
page 9-8
Replace the cartridges
See the plotter’s current configuration
Clear a media jam
Solve print quality problems
Interpret a front-panel message
Order accessories
page 9-16
page 10-2
page 11-13
To find any other information ...
" go to the index at the back
of this manual.
On page D-1 at the back of this manual, you will find a Documentation Map,
listing useful documents to help with
Setting Up and Using the Plotter
Using Application Software
Getting Support
Programmer’s References.
iv
Contents
Finding Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
1 Setting Up the Plotter
Fast Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Set Up Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Task 1: Check that You Have All the Items Required . . . . . . . . . . . . . . . . . . . . . 1-5
Task 2: Install Memory Expansion Modules (Optional) . . . . . . . . . . . . . . . . . . . 1-6
Task 3: Switch On and Change the Language From English (Optionally) . . . . . 1-9
Task 4: Load Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
Task 5: Load the Print Cartridge(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20
Task 6: Print a Demonstration Plot (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . 1-24
Task 7: Connect the Plotter To Your Computer . . . . . . . . . . . . . . . . . . . . . . . . . 1-27
Task 8: Configure the Serial Interface (Serial Interface Users Only) . . . . . . . . 1-29
Task 9: Set Up Your Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-35
Task 10: Print a Test Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-39
Extra Tips for UNIX Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-40
2 Learning How to Use the Front-Panel Display (Tutorial)
The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
The Display Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Printing the Menus Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Description of the Menus Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Entering the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Navigating the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Menu Graphics Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Other Types of Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
v
Contents
3 Working with Media and Cartridges
Choosing Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Five Important Points about Media Types . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Supported Media Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Physical Characteristics of Media Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Cost And Color Support of Media Types (DesignJet 750C Plus) . . . . . . . . . 3-5
Combinations of Media Type and Print Quality . . . . . . . . . . . . . . . . . . . . . . . 3-6
Typical Media Type Choices by Application . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Caring For Your Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Loading Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
To Change a Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
To Load a Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Compensating for Badly Cut Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
To Adjust Skew Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Unloading Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Drying Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
To Adjust Drying Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
To Unload a Sheet After Plotting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
To Remove an Unused Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
Replacing Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
When to Replace Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Before Replacing Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
To Replace a Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
vi
Contents
4 Controlling the Page Format
Page Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Do You Need to Adjust the Page Size in the Front Panel? . . . . . . . . . . . . . . . 4-3
To Adjust the Page Size from the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Page Size and Clipped Plots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Page Size and Nesting (Roll Media Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Adjusting the Margins (Roll Media Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Margins and Automatic Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Rotating a Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Rotating a Drawing from the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
To Rotate a Plot from the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Exactly What Is Rotated? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
The Rotate Feature and Clipped Plots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
How Does Rotate Interact with Your Software? . . . . . . . . . . . . . . . . . . . . . . . 4-9
Plotting a Mirror Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
5 Controlling a Plot’s Overall Appearance
Ways To Control the Plot’s Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Why Change the Appearance of the Plot Using the Front Panel Rather Than
from Your Software? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Changing Pen Widths and Colors/Shades Using the Plotter’s Internal Palettes . 5-3
To See the Current Palette Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
To See the Colors Available For a Palette (DesignJet 750C Plus) . . . . . . . . . 5-4
To Change the Palette Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
To Change the Selection of the Current Palette . . . . . . . . . . . . . . . . . . . . . . . 5-6
Changing the Treatment of Overlapping Lines (Merge Feature) . . . . . . . . . . . . 5-7
Changing the Overall Lightness/Darkness of a Plot . . . . . . . . . . . . . . . . . . . . . . 5-8
Printing Color Drawings in Monochrome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
To Switch between Color and Monochrome . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Choosing an Appropriate Print Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
To Change the Print Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Improving Line Quality and Graphics Detail (DesignJet 750C Plus) . . . . . 5-14
vii
Contents
6 Managing Your Plots
Managing Plots Currently Being Printed or Drying . . . . . . . . . . . . . . . . . . . . . . 6-2
To Cancel a Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
To Cut a Plot Before Drying Is Complete (Roll Media Only) . . . . . . . . . . . . 6-2
To Pause while Printing a Series of Plots . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Managing Plots Not Yet Printed (The Queue) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
To Start Printing a Plot That Is Waiting for a Timeout . . . . . . . . . . . . . . . . . . 6-4
What Is the Queue? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
To Identify a Page in the Queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
To See the Size of a Page in the Queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
To Prioritize a Page in the Queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
To Delete a Page from the Queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
To Make Copies of a Page in the Queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
To Replot an Image Using the Plotter’s Memory (DesignJet 700) . . . . . . . . . . . 6-9
Avoiding Media Waste by Nesting Pages (Roll Media Only) . . . . . . . . . . . . . . 6-10
What Is Nesting? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
When Does the Plotter Try to Nest Pages? . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Which Pages Qualify for Nesting? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Which Pages May be Rotated? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
To Turn Nesting On or Off and Choose the Nesting Method . . . . . . . . . . . . 6-12
What Happens to Nesting if You Turn Queueing Off? . . . . . . . . . . . . . . . . . 6-12
How Long Does the Plotter Wait for Another File? . . . . . . . . . . . . . . . . . . . 6-12
Getting the Best From Nesting (Nesting and Margins) . . . . . . . . . . . . . . . . 6-13
Nesting and the Rotate Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
viii
Contents
7 Reconfiguring the Plotter
To See the Current Overall Configuration of the Plotter . . . . . . . . . . . . . . . . . . . 7-2
To See the Current Configuration of the Front-Panel Settings . . . . . . . . . . . . . . 7-3
To Change the Front-Panel Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Recalibrating the Plotter for Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
When to Recalibrate the Plotter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
A Quick Guide to Whether Recalibration Is Necessary . . . . . . . . . . . . . . . . . 7-5
To Recalibrate the Plotter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
To Restore the Factory’s Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
Changing the Graphics Language Setting for a Different Application . . . . . . . . 7-7
To Change the Graphics Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
Graphics Language and Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Changing the Serial Interface Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
To Change the Serial-Interface Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
Change the I/O Timeout Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
To Upgrade Your Plotter with More Memory . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
File Size and Memory Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
To Upgrade Your Plotter with the Postscript Option . . . . . . . . . . . . . . . . . . . . . 7-11
To Upgrade Your Plotter with a Network Interface . . . . . . . . . . . . . . . . . . . . . . 7-12
HP JetDirect Print Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
8 Maintaining the Plotter
Replacing the Print Cartridge(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Cleaning the Plotter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
“Normal” Plotter Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
To Print the Service Configuration Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
ix
Contents
9 Troubleshooting
Using the Documentation to Help Solve Problems . . . . . . . . . . . . . . . . . . . . . . . 9-2
Locating the Source of the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Solving Media-Handling Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
If the Front Panel Keeps Telling you Media Is Misaligned or Incorrectly
positioned. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
If Media Crumples when you Load It . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
If Plots Do Not Feed Out Properly From the Plotter . . . . . . . . . . . . . . . . . . . 9-5
If The Automatic Cutter Does Not Cut Immediately When a Plot Has
ąFinished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
If The Automatic Cutter Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
If Plots Fall On the Floor After Being Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
If a Sheet Is Ejected When You Switch On the Plotter . . . . . . . . . . . . . . . . . 9-6
If Plots Do Not Stack Properly In the Bin . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
Solving Print Cartridge Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
If the Access Cartridge(s) Key Does Not Work . . . . . . . . . . . . . . . . . . . . . . . 9-7
If the Plotter Runs the Cartridge-alignment Routine Unexpectedly . . . . . . . . 9-7
If Brand New Cartridge(s) Have Problems . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Clearing a Media Jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Solving Communication Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
If There is a Problem Communicating between Your Computer
and the Plotter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Solving Problems with Plot Position or Content . . . . . . . . . . . . . . . . . . . . . . . . 9-10
If the Plot Is Completely Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
If the Output Contains Only a Partial Plot . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
If the Plot Is Clipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
If a Long-axis Plot Is Clipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
If the Entire Plot Is in One Quadrant of the Correct Plotting Area . . . . . . . 9-13
If the Plot Is Unexpectedly Rotated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
If the Plot Is a Mirror Image of Your Drawing . . . . . . . . . . . . . . . . . . . . . . . 9-13
If the Plot Is Inaccurate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
If the Plot Is Distorted or Unintelligible . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
If One Plot Overlays Another Plot On the Same Sheet . . . . . . . . . . . . . . . . 9-14
If Pen Settings Seem to Have No Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
x
Contents
If the Plotter Produces a Black and White Plot When You Expected a Color
ąPlot (DesignJet 750C Plus) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
If the Plotter Has Printed a Different Plot Than the One You Were
ąExpecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
If the Quality Of a Color Plot Is Not as Good as You Were Expecting
(DesignJet 750C Plus) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
Solving Print Quality Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
If the Color Is Not as Expected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
If there are White Streaks in Solid Fill Areas . . . . . . . . . . . . . . . . . . . . . . . . 9-16
If there are Other Gaps in Solid Areas or in Lines (DesignJet 750C Plus) . 9-17
If there are Jagged Vertical or Horizontal Lines . . . . . . . . . . . . . . . . . . . . . . 9-18
If there are Slightly Warped Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-18
If there are Color “Shadows” (DesignJet 750C Plus) . . . . . . . . . . . . . . . . . . 9-18
If One or More Cartridges are not Printing at All . . . . . . . . . . . . . . . . . . . . 9-18
If there are Blurred Lines (Ink “Bleeds” from Lines) . . . . . . . . . . . . . . . . . . 9-19
If there are Blotchy Areas (Uneven Fill Density) . . . . . . . . . . . . . . . . . . . . . 9-19
If the Plot Is Too Dark or the Color Too Saturated . . . . . . . . . . . . . . . . . . . . 9-19
If there Is Pronounced Banding In Area Fills . . . . . . . . . . . . . . . . . . . . . . . . 9-20
If Ink Smears After You Remove a Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20
Solving Front Panel Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
If the Access Cartridges Key Does Not Work . . . . . . . . . . . . . . . . . . . . . . . 9-21
If None of the Front Panel Keys Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
If Page Format/Rotate Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
If A Display Message Will Not Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
If A “System Error” Message Is Displayed . . . . . . . . . . . . . . . . . . . . . . . . . 9-22
If An “Out Of Memory/Data Was Lost” Message Is Displayed . . . . . . . . . . 9-22
Solving Miscellaneous Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
If the Plotter Does Not Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
If the Plotter Seems Too Slow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-23
If the Plotter Waits Too Long to Plot a Nest . . . . . . . . . . . . . . . . . . . . . . . . . 9-24
If the Plotter Performs the Cartridge Alignment Routine Unexpectedly . . . 9-24
If the Bail (Black Metal Bar) Does Not Lower All the Way . . . . . . . . . . . . 9-24
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
What to Do Before You Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
If a Repair Is Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
xi
Contents
10 Front-Panel Messages
Front Panel Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
11 Reference
Plotter Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
Interface Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10
To Obtain a Material Safety Data Sheet (MSDS) . . . . . . . . . . . . . . . . . . . . 11-10
Electromagnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10
Telecommunications Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
Ordering Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13
HP-GL/2 and HP RTL Programming Information . . . . . . . . . . . . . . . . . . . 11-16
How to Order Supplies and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16
12 Glossary
Index
Documentation Map
Please Give Us Your Feedback (Removable)
xii
Welcome
Welcome
An Introduction To Your Plotter’s Main Features
The HP DesignJet 700 and HP DesignJet 750C Plus are large-format inkjet plotters
that use HP disposable print cartridge technology.
700
The HP DesignJet 700 will print only in black. It uses a single cartridge,
containing black ink, two of which are supplied with your plotter.
The HP DesignJet 750C Plus will print in color or black. Your
plotter uses a set of four disposable print cartridges: yellow,
cyan, magenta and black. a set is supplied with your plotter (a
spare black cartridge is also included). From time to time, you
will need to replace them. All other supported colors are
generated using these four cartridges up to a total of over 16
million different colors for all your needs.
750C Plus
Product C4705A is the DesignJet 700 and Product C4708A is the DesignJet
750C Plus. Both Plotters are the D/A1-size model.
Product C4706A is the DesignJet 700 and Product C4709A is the DesignJet
750C Plus. Both Plotters are the E/A0-size model.
xiii
Welcome
Print Quality
In monochrome, the print resolution can be set to either true 300 or true 600 dots
per inch (dpi). In color, the print resolution can be set to true 300 or addressable
600 dpi. You can choose between three levels of print quality either from your
software or from the plotter’s front panel. These are:
Best
Normal
Fast.
Media
You can plot on rolls or sheets up to E/A0 size or D/A1 size, depending on the
plotter model you have bought.
A large variety of media types are supported:
Opaque bond (one roll is supplied with your plotter)
Translucent bond
700
Natural tracing paper
Vellum
750C Plus
Coated paper (one roll is supplied with your plotter)
Heavy coated paper
Matte and clear film.
In addition for the HP DesignJet 750C Plus:
High-gloss and semi-gloss photo paper
High-gloss film.
750C Plus
xiv
Welcome
User Interface
xxxxxxx
yyyyy
The plotter’s front panel includes an easy-to-use interface with a two-line display,
giving you access to a comprehensive set of plotter functions and to a number of
useful sample plots.
This manual includes a short tutorial to teach you how to navigate around the
menus. Wherever a front-panel feature is explained in this manual, a simple
graphic shows you how to access that feature from the front-panel menus.
Queueing & Nesting
Queue mgmt
Page ID
Software Applications and Drivers
To make sure that your plotter prints exactly what you were expecting – in terms of
size, position, orientation, color and quality – the key is to use the correct driver for
the combination of your application software and your plotter, and to be confident
that it is configured correctly.
Two types of HP drivers are supplied with your plotter:
One or more for AutoCAD users,
One for users of MicrosoftR Windows applications.
These drivers come with printed and on line documentation to help you install and
configure them correctly.
Generally, software applications include their own drivers too. With this plotter we
have provided free of charge a set of Software Application Notes for the most
popular applications. If you find your own application in these notes, we
recommend that you use the information they contain as an overall guide to
configuring the software for your plotter.
xv
Welcome
Memory and Upgrades
Your plotter comes with a standard memory of 5.5 MB (4 MB of main memory
and 1.5 MB of printing memory). In case you need to print particularly large
1
files , you can upgrade your plotter with up to two 32 MB memory expansion
modules, taking the maximum memory up to 69.5 MB (5.5 + (2 x 32)).
700
Your plotter comes with a standard memory of 11 MB (8 MB of main memory and
1
3 MB of printing memory). In case you need to print particularly large files , you
can upgrade your plotter with up to two 32 MB memory expansion modules,
taking the maximum memory up to 75 MB (11 + (2 x 32)).
750C Plus
Other upgrades available are:
A PostScriptr upgrade kit (including a ROM SIMM for the plotter and an
Adobe PostScript driver for your software).
A network interface card (the HP JetDirect Print Server).
1
Note that there is not a one-for-one relationship between the plotter’s memory and the maximum size
of file that it can plot.
xvi
Welcome
Front View
Window
Print Cartridge(s)
(Inside)
Front Panel Display
Front Panel
Media Lever
Media-Entry Slot
ON/OFF Switch
Roll Cover
Media Bin
1835
xvii
Welcome
Rear View
Parallel-Interface
Serial-Interface
Slot For Optional Network Interface
Socket For
Power Cord
Pocket For
Quick Reference Guide
And Media Knife
Slots For Memory Expansion
Modules and Upgrades
(Behind Cover Plate)
1844
xviii
1
Fast Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Set Up Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Task 1: Check That You Have All the Items Required . . . . . . 1-5
Task 2: Install Memory Expansion Modules (Optional) . . . . 1-6
Task 3: Switch On and
Change the Language From English (Optional) . . . . 1-9
Task 4: Load Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
Task 5: Load the Print Cartridge(s) . . . . . . . . . . . . . . . . . . . 1-20
Task 6: Print a Demonstration Plot (Optional) . . . . . . . . . . . 1-24
Task 7: Connect the Plotter to Your Computer . . . . . . . . . . . 1-27
Task 8: Configure the Interface (Serial interface users only) 1-29
Task 9: Set Up Your Software . . . . . . . . . . . . . . . . . . . . . . . 1-35
Task 10: Print a Test Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-39
Extra Tips For UNIX Users . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-40
Setting Up Your Plotter
Installation, Connection,
and Configuration
1-1
Setting Up the Plotter
Fast Track
Fast Track
If You Meet All the Following Requirements:
You want English as the language of the front-panel display and of the plotter’s
internal plots.
You are experienced at installing printers or plotters.
You don’t want to add extra memory.
For the HP DesignJet 700:
700
You are going to use roll media.
For the HP DesignJet 750C Plus:
750C Plus
You are going to use roll media and print in color.
You know whether to connect the plotter directly to your computer or to a
network and whether to use the parallel or serial interface, and you already have
the right cable.
(Serial interface users) Your computer’s RS-232-C settings are 9600 baud, no
parity, 8 data bits and 1 stop bit.
... Just Do the Following Six Steps and Skip the Rest of This Chapter.
1 Connect the power cord and switch on.
2 Load the roll of media supplied, following the instructions on the label inside
the plotter’s roll cover. Watch the front-panel display for further instructions.
3 Press Access Cartridge(s) and open the plotter window.
For the HP DesignJet 700:
700
Load the black print-cartridge into the carriage on the left side of the plotter.
Don’t forget to remove the tape from the cartridge.
For the HP DesignJet 750C Plus:
750C Plus
Load the four color print-cartridges into the carriage on the left side of the
plotter. Don’t forget to remove the tape from the cartridges.
Continued...
1-2
Setting Up the Plotter
Fast Track
4 Close the plotter’s window and let the plotter run its automatic
cartridge-alignment procedure.
5 Switch off the plotter and your computer, connect the interface cable, and
then switch them on again.
6 Choose your driver disk(s), read the instructions on the label, and follow
any printed instructions accompanying the disks. For AutoCAD or
Microsoft Windows applications, the driver is shipped with the plotter.
For other applications, see page 1-38 for advice, and, if necessary, contact
your software vendor.
1-3
Setting Up the Plotter
Set Up Checklist
Set Up Checklist
You should already have unpacked and assembled the plotter, following the
Assembly Instructions in the box. Now you can set up the plotter, using the
checklist below as you complete each task explained in this chapter.
Task
1
Done? (n)
Check that you have all the items required.
Install memory expansion modules (Optional).
Switch on and change the language from English (Optional).
Load media.
2
3
4
Load the print-cartridge(s).
5
Print the demonstration plot (Optional).
Connect the plotter to your computer.
Configure the interface (Serial interface users only).
Set up your software.
6
7
8
9
Print a test plot.
10
1-4
Setting Up the Plotter
Task 1: Check That You Have All the Items Required
Task 1: Check That You Have All the Items Required
Supplied
1 You need the following items, which were supplied with the plotter.
Power cord
The power cord supplied with your plotter should meet the plug requirements for
your area. However, different power cords (international options) are available. If
necessary, contact your dealer or HP Sales and Support Office.
A roll of HP Opaque Bond Paper (for the HP DesignJet 700)
A roll of HP Coated Paper (for the HP DesignJet 750C Plus)
Print cartridge(s):
For the HP DesignJet 700:
– Two black
700
For the HP DesignJet 750C Plus:
– One yellow
– One cyan
750C Plus
– One magenta
– Two black
2 Inspect the plotter itself and the above accessories. If you received any item in a
damaged condition, notify the dealer or HP Sales and Support Office where you
purchased the plotter, and file a claim with the carrier.
Not supplied
Optional
3 You will also need the following items, which were not supplied with the plotter.
Interface cable
For details of suitable cables, see page 11-8.
4 If you have purchased extra memory, you will need your
Memory expansion module
For details of the memory expansion modules available, see page 11-14.
1-5
Setting Up the Plotter
Task 2: (Optional) Install Memory Expansion Modules
Task 2: Install Memory Expansion Modules (Optional)
Your plotter comes with 5.5 MB of standard memory.
700
Your plotter comes with 11 MB of standard memory.
750C Plus
You can expand this by adding one or two memory expansion modules, in any
combination. Supported sizes are 4 MB, 8 MB, 16 MB and 32 MB. So the
maximum standard memory for your plotter is:
5.5 + 32 + 32 = 69.5 MB
11 + 32 + 32 = 75 MB
700
750C Plus
For HP part numbers, see page 11-14.
1
Make sure that the plotter is switched OFF and that neither the power cord
nor an interface cable is connected.
X
X
1847
1-6
Setting Up The Plotter
Task 2: (Optional) Install Memory Expansion Modules
2
Using a flat-blade screwdriver, unscrew the cover plate at the back of the
plotter, and remove it. Unscrew only the four screws on the cover plate.
Cover plate
The two slots on the right are for memory expansion modules. Use slot 3
first, and then slot 4.
Slot for first memory module installed
Slot for second memory module installed
1 2 3 4
If your plotter has only one memory module, it must be in slot number 3.
1845a
1-7
Setting Up the Plotter
Task 2: (Optional) Install Memory Expansion Module
Before handling a memory module, either put on a grounding wrist strap and
attach the end to the metal chassis of the plotter, or touch the outer metal
surface of the plotter with your hand. Otherwise, static electricity from your
body could damage the memory module.
C A U T I O N
3 Take the memory module out of its bag, holding the module only by the edges.
4
a Hold the module by its
edges with the
Grounding
Wrist Strap
nonmetallic edge toward
you and the small notch
at the bottom.
b With the nonmetallic
edge angled to the right,
firmly push the module
into the slot. Gradually
straighten the angle and
push it in until it clicks
into place.
1846
5
Using a flat-blade screwdriver, replace the cover plate and its four screws.
1845b
1-8
Setting Up the Plotter
Task 3: Switch On and (Optional) Change the Language From English
Task 3: Switch On and Change the Language From
English (Optional)
The plotter’s front-panel menus and all the plotter’s sample plots are available in
1
the following languages : English, French, German, Italian, Japanese, Portuguese,
and Spanish. By default, the language is English.
Be sure that the power cord supplied with your plotter matches your ac power
connection requirements. Use only three-wire (earth-grounded) power cords
with this plotter.
W A R N I N G
1 Make sure that the power switch on the front of the plotter is OFF.
2
Plug the power cord into the socket at
the back of the plotter, and then into
your power outlet.
1848
If English OK
or if you have
already
3
Switch on the plotter by pushing the power switch. Then go to Step 4.
changed the
language
on
If there is no sound, nor any light on the front panel, you have a power problem.
1843
1
The physical front-panel overlay is also available in Chinese, Korean and Taiwanese.
1-9
Setting Up the Plotter
Setup Task 3: Switch On and (Optional) Change the language From English
If English not OK
or if you want
to change the
language
4
Hold down the Enter key on the front panel and then switch on the plotter by
pushing the power switch.
Enter
1 Press and hold
2 Switch on
Release the Enter key when “STATUS / Initializing” appears on the front-panel
screen. If there is no sound, nor any light on the front panel, you have a power
problem.
1843a
5
When the word “English” appears on the front-panel screen, press the ↑ or
↓ key until your language appears. Then press Enter.
↑
LANGUAGE
English
↓
Enter
0014
1-10
Setting Up the Plotter
Task 4: Load Media
Task 4: Load Media
For advice on the availability and use of different media types, see the section
starting on page 3-2.
IMPORTANT
Because the next task is to load the cartridge(s) and carry out the automatic
cartridge alignment procedure, you must load opaque media at this stage – for
example, opaque bond (plotter paper) for the DesignJet 700 or coated paper for the
DesignJet 750C Plus, as this necessary for the alignment procedure. A roll of
suitable HP Media is supplied with your plotter.
To load roll media, start with step 1 below.
To load sheet media, go to page 1-18.
To Load a Roll
1 Make sure the plotter wheels are locked (the brake levers pressed down) to prevent
the plotter from moving.
2
Open the roll cover and remove the empty spindle by pulling firmly on each
end. The two ends are different: end A has a media stop and end B a smaller
end cap, as shown on the next page.
B
Roll cover
A
Place the spindle vertically on the floor, with the media stop at the bottom,
ready for the new roll.
1865
1-11
Setting Up the Plotter
Task 4: Load Media
3
Remove the new roll from its wrapping. Remove the end cap from the top
of the spindle, and slide the new roll onto the spindle. The leading edge of
the media must wind clockwise.
End cap removed.
If the media stop falls off, push it back
in until it snaps into position.
A
0015
4
Push the end cap back in, making sure that the tabs are flush against the ends of
the roll. Push it far enough to be firm, but do not use excessive force as this
may break the tabs.
B
0016
1-12
Setting Up the Plotter
Task 4: Load Media
5
Insert the spindle so that the large media stop (A) is to the right and the
small end cap (B) to the left. Push in firmly on both ends. Be sure the
media remains flush against the media stop.
B
A
A
Media path
0017
The relationship of the media to the roller must be as shown in the
diagram above.
1837
6 Check the leading edge as it unwinds from the spool. If it is uneven, trim it as
explained in step 7. Otherwise go to step 8.
1-13
Setting Up the Plotter
Task 4: Load Media
The media cutting knife used in the next step is sharp. Make sure the plotter’s
wheels are locked. Keep fingers clear of the cutting path. Keep media cutting
knife away from children.
W A R N I N G
7
Trim the leading edge of the media roll:
a Pull the media over the top of the machine and lay it over the cutting track.
b Use the media cutting knife in the pocket located at the back of the plotter
to cut off the first few inches of the media.
c Retract the blade and return the media cutting knife to its pocket.
1838
1-14
Setting Up the Plotter
Task 4: Load Media
8
a Pull the media towards you and, holding it from the sides, align its right
edge with the perforated line on the entry platen.
b Insert the leading edge into the plotter, until the page buckles slightly.
c Let go of the media when the plotter begins to pull it in.
1839
9
Press the ↓ key next to the front-panel display to indicate you are loading a roll.
↑
Sheet load
Roll load
––––––––>
––––––––>
↓
0014
1-15
Setting Up the Plotter
Task 4: Load Media
10 Press the ↑ or ↓ key until the display shows the type of media you are loading and
then press the Enter key.
↑
SELECT MEDIA
Opaque bond
↓
Enter
700
(if you are using the roll supplied with the plotter,
scroll to Opaque bond)
0014
↑
SELECT MEDIA
Coated paper
↓
Enter
750C Plus
(if you are using the roll supplied with the plotter,
scroll to Coated paper)
0014
1-16
Setting Up the Plotter
Task 4: Load Media
11
a When the front panel instructs you, lift the media lever.
b Take hold of the edges of the media now extending from the exit slot and pull
the media toward you until taut. Then align the left and right edges of the
media so that they are flush with the edges of the roll.
A
B
c When the front panel instructs you, lower the media lever.
0018
12 a When the plotter instructs you to close the roll cover, rewind the media stop
in the direction shown by the large arrow below, to take up any slack in the
roll. Make sure that the leading edge of the media is outside the roll cover,
and then close the cover.
b Press the ↓ key to continue. The plotter automatically trims off the first few
inches of media.
c The roll media is now loaded and ready for plotting.
1840
1-17
Setting Up the Plotter
Task 4: Load Media
To Load a Sheet
You can load a sheet in either portrait or landscape orientation. (Your choice of
orientation is significant when sending a plot from your software, but for the
moment it doesn’t matter.)
or
Printing will be on the underside. So, if loading Coated paper, load with
the coated side down. For advice on other media types, see page 3-18.
1 Make sure the media lever is down and the roll cover is closed.
2
a Holding the media from the sides, align the right edge with the perforated
line on the entry platen.
b Insert the media until it buckles slightly, that is, push all the way to the
media stops. Let go of the media when the plotter begins to pull it in.
1841
1-18
Setting Up the Plotter
Task 4: Load Media
3
Press the ↑ key next to the front-panel display to indicate you are loading a
sheet.
↑
↓
Sheet load
Roll load
––––––––>
––––––––>
0014
4
Press the ↑ or ↓ key until the display shows the type of media you are loading
(if you are using regular plotter paper, scroll to Opaque bond; if coated paper,
scroll to Coated paper), and then press the Enter key.
↑
SELECT MEDIA
Opaque bond
↓
Enter
0014
5 The plotter moves the sheet in and out to check its size and alignment, and then
advances it to the start of the page. When sheet loading is complete, STATUS /
Ready is displayed.
If you have persistent difficulty loading media, this may indicate poorly cut media
– see page 3-21 for advice.
1-19
Setting Up Your Plotter
Task 5: Load the Print Cartridge(s)
Task 5: Load the Print Cartridge(s)
Cartridge types
IMPORTANT Your plotter is designed to operate only with the cartridges whose
part numbers are listed on page 11-15, and samples of which are supplied with the
plotter.
The HP DesignJet 700 is supplied with two black cartridges (one is a spare cartridge).
700
The HP DesignJet 750C Plus is supplied with five cartridges:
750C Plus
– yellow
– cyan
– magenta
– black (plus one spare black cartridge)
For the 750C Plus, each stall in the carriage has a dot indicating the color of the
cartridge that should be installed. You must put the correct cartridge in the correct
stall otherwise not only will your colors be wrong, but also print quality may be
impaired. The sequence of the colors is, from left to right, yellow, cyan, magenta
and black.
Yellow
Cyan
Magenta
Black
00019
For users with color-vision deficiencies. You can identify the colors of the
cartridges by the part numbers on the boxes – see page 11-15.
Note. Except on glossy media types, the plotter will operate successfully in
monochrome with just the black cartridge loaded, but these instructions assume
that you are loading all four cartridges.
1-20
Setting Up Your Plotter
Task 5: Load the Print Cartridge(s)
Do not touch the stainless steel strip that runs the length of the plotter behind
the cartridge carriage; its edge is very sharp. Keep hair, jewelry, clothing,
and foreign objects away from the plotter mechanisms.
W A R N I N G
a Press the Access Cartridge(s) key and wait for the cartridge carriage
1
to come to a complete stop next to the front panel.
b When the carriage stops, open the window.
750C Plus
700
1849
It is essential to load the cartridge(s) with the plotter switched ON, otherwise
you will get poor print quality, and the reliability of your cartridge(s) will be
impaired.
C A U T I O N
Keep new and used print cartridge(s) out of the reach of children.
W A R N I N G
1-21
Setting Up Your Plotter
Task 5: Load the Print Cartridge(s)
2
For each cartridge in the set:
a Take the cartridge out of its box.
b Remove the colored protective tape and tab
from the cartridge’s nozzles.
1754
For the 750C Plus, match the color of the cartridge’s label
with the color of the dot above the stall.
750C Plus
c Make sure that the plotter is still switched ON (Never install cartridges
with the plotter switched OFF).
d Insert the cartridge in the stall. Press down lightly and push the cartridge
away from you until it snaps into place. If the front-panel display says
Reseat cartridge(s), then remove the cartridge and insert it again. Do so
until the message disappears.
Yellow
Cyan
Magenta
Black
2
1
0019
2
750C Plus
1
r004
700
1-22
Setting Up Your Plotter
Task 5: Load the Print Cartridge(s)
3 When the cartridges are successfully installed, the plotter automatically runs the
cartridge alignment procedure. When the front-panel displays STATUS / Ready,
the procedure is complete. You can throw away the small print produced during
the cartridge alignment procedure.
To make your cartridges last as long as possible, you should not remove them once
they are installed, except to replace them.
Now that the cartridge(s) are loaded, never turn the plotter upside down, or
ink will spill.
C A U T I O N
1-23
Setting Up the Plotter
Task 6: (Optional) Print a Demonstration Plot
Task 6: Print a Demonstration Plot (Optional)
Before you connect your plotter to a computer, it is a good idea to print one of the
internal sample plots. This ensures that the plotter itself is operating properly.
1 If media is not already loaded, load a roll or a sheet, as explained earlier in task 4.
For advice on the availability and use of different media types, see the section
starting on page 3-2.
1-24
Setting Up the Plotter
Task 6: (Optional) Print a Demonstration Plot
2
On the front-panel display, go to Demos, as shown below.
STATUS
Ready
Press Enter
SHORT MENUS
Queueing & Nesting ³
Press ↓
SHORT MENUS
Demos ³
Press Enter
DEMOS
Palette
750C Plus
Press Enter to choose this or ↓ to get to the next option
DEMOS
Samples
Press Enter to choose this or ↓ to get to the next option
DEMOS
Menu
Press Enter
Palette prints the Palette Demo, which is explained on page 5-4.
750C Plus
Samples accesses a list of sample demonstration plots stored in the plotter’s
firmware. If only one is available, it starts processing as soon as you press
Enter.
Menu prints a menu tree of the entire front-panel menu structure.
1-25
Setting Up the Plotter
Task 6: (Optional) Print a Demonstration Plot
3 The Receiving light flashes while the plot is being processed, and then the plotter
starts printing. After it has finished:
On roll media, the plotter waits for the ink to dry, if necessary, and drops the
plot into the media bin.
On sheet media, wait until the ink is dry, if necessary (see the front-panel
display for an ink-drying message), and then gently pull the sheet out from the
plotter. On HP Coated Paper you don’t need to wait at all.
4 Examine the plot, with the following questions particularly in mind:
Are the lines clean and complete?
Are the area fills smooth?
Are the black and white areas correctly defined?
Is the color of good quality?
700
750C Plus
Unless you changed it, the print-quality setting on the front panel was Best. If you
have any concerns about the print quality of the sample plot, use the
troubleshooting advice starting on page 9-16.
1-26
Setting Up the Plotter
Task 7: Connect the Plotter to Your Computer
Task 7: Connect the Plotter to Your Computer
For UNIX systems, see also the tips starting on page 1-40.
If You Are Connecting the Plotter Directly to a Network
You can connect your plotter directly to a Local Area Network using an optional
network interface card such as the HP JetDirect Print Server. Depending on
your needs, you may want to use the network interface instead of, or in addition to,
the parallel and serial interfaces.
The slot for a network interface card is situated at the back of the plotter,
alongside the parallel and serial ports. Using a flat-head screwdriver, unscrew
only the two screws on its cover plate.
Slot for Network Interface Card
For installation and configuration of the HP JetDirect Print Server, see the
documentation supplied with that product.
1845c
1-27
Setting Up the Plotter
Task 7: Connect the Plotter to Your Computer
If You Are Connecting the Plotter Directly to Your Computer
1 Decide whether to use the parallel or serial interface.
If your computer and your application software support it, use the parallel
interface, as it is faster. You can connect both the parallel and the serial interface
simultaneously if you wish: the plotter uses the interface that first receives data.
2 Choose an interface cable.
A list of recommended HP cables for various computers starts on page 11-8.
IMPORTANT
To achieve the best performance from your plotter, we recommend you only use
genuine Hewlett-Packard interface cables, whose reliability and performance have
been thoroughly tested to give trouble-free performance.
3 Switch OFF the plotter and then the computer.
4
Connect one end of the cable to the appropriate port on the back of the plotter.
Port for parallel-interface
cable (plotter end of cable:
36-pin male)
Port for serial-interface cable
(plotter end of cable:
25-pin male)
1844
5 Connect the other end of the cable to your computer. For help on choosing the
correct port on the computer, refer to your computer documentation.
6 Switch ON the computer and then the plotter.
1-28
Setting Up the Plotter
Task 8: (Serial Interface Users Only) Configure the Interface
Task 8: Configure the Interface (Serial Interface Users
Only)
The following table shows the settings available for the plotter’s serial interface
parameters, the factory defaults and the most likely requirements for different
computers.
Serial (RS-232-C) Settings
Likely requirement for ...
Available
settings
PC
Macintosh
Unix
Parameter
Baud rate
1200
2400
4800
9600
19200
38400
9600
None
9600
None
(2)
(2)
(1)
Parity
None
Even
Odd
Italics = factory default
(1)
Parity of None = 8 data bits, 1 stop bit
Parity of Even or Odd = 7 data bits, 1 stop bit
(2)
Consult your software documentation.
The settings on the plotter must match those of the computer and software sending
the data. Use their documentation to find the requirements. If in doubt, try with
the above suggestions. If the plotter’s defaults already match the requirements,
then you can skip the rest of this task.
1-29
Setting Up the Plotter
Task 8: (Serial Interface Users Only) Configure the Interface
To Change the Plotter’s Serial Interface Settings
Through the front-panel display, you can create and save two sets of configurations
for the serial interface, called Configurations A and B. By default they are set to
the factory defaults shown in the table on page 1-29. The factory default
configuration is always available as well, giving you up to three stored
configurations to choose from.
The instructions that follow explain how to specify and apply Configuration A.
Configuration B can be specified in the same way. To restore the factory default
configuration see page 7-6
1-30
Setting Up the Plotter
Task 8: (Serial Interface Users Only) Configure the Interface
1
On the front-panel display, change the Menu mode from Short to Full.
STATUS
Ready
Press Enter
SHORT MENUS
If FULL MENUS is displayed instead
of SHORT MENUS, you can skip this
step and go to step 2.
Queueing & Nesting ³
Press ↓
SHORT MENUS
Demos ³
Press ↓
UTILITIES
Menu mode=Short ³
Press Enter
MENU MODE
Short*
Press ↓
MENU MODE
Full
Press Enter
UTILITIES
Menu mode=Full ³
Press Previous
FULL MENUS
Utilities ³
1-31
Setting Up the Plotter
Task 8: (Serial Interface Users Only) Configure the Interface
2
Get to the routine for defining a new serial configuration.
FULL MENUS
Utilities ³
Press ↓
FULL MENUS
I/O setup ³
Press Enter
I/O SETUP
Modular ³
Press ↓
I/O SETUP
RS–232–C ³
Press Enter
RS–232–C
Config=Factory ³
Press ↓
RS–232–C SETUP
Define config
Press Enter
DEFINE CONFIG
Config A ³
Press Enter
CONFIG A
Baudrate=9600
1-32
Setting Up the Plotter
Task 8: (Serial Interface Users Only) Configure the Interface
3
Configure the serial interface to match your software configuration.
This example changes the configuration
CONFIG A
to 19200 Baud and Even parity.
Baudrate=9600 ³
Press Enter
BAUDRATE
9600*
Press ↑
BAUDRATE
19200
Press Enter
CONFIG A
Baudrate=19200 ³
Press ↓
CONFIG A
parity=None(0) ³
Press Enter
PARITY
none(0)*
Press ↓
PARITY
Even
Press Enter
CONFIG A
RS–232–C
Parity=Even ³
Config=Factory ³
Press Previous until you return to ...
1-33
Setting Up the Plotter
Task 8: (Serial Interface Users Only) Configure the Interface
4
Switch to the new configuration.
RS–232–C
Config=Factory ³
Press Enter
CONFIG
Factory*
Press ↓
CONFIG
Config A
Press Enter
RS–232–C
Config=A ³
STATUS
Press Previous until you return to ...
Ready
1-34
Setting Up the Plotter
Task 9: Set Up Your Software
Task 9: Set Up Your Software
This section gives a simple overview of the software-configuration tasks you need
to perform and is designed for those users unfamiliar with this type of task. It also
points to documents containing detailed, application-specific advice.
More experienced users may prefer to go straight to those documents.
For UNIX systems, see also the tips starting on page 1-40.
Basic Terminology
Application software
Application software means the software from which you intend to send plots to
your plotter – for example, a CAD system, a graphics package, a desktop
publishing system etc.
Drivers
Your application software needs to know to which type of plotter it is sending
information. This knowledge, and other configuration information, is held in a
“driver.” The driver is a piece of software that handles communications between
your application software and your plotter.
To make sure that your plotter prints exactly what you expect – in terms of size,
position, orientation and quality – use the correct driver for the combination of
your application software and your plotter.
1-35
Setting Up the Plotter
Task 9: Set Up Your Software
Typical Checklist of Tasks to Set Up Your Software
1 Identify which driver you need.
Some are supplied with this plotter, as listed in the table on page 1-37. Others are
supplied with your application software.
2 If necessary, install the driver on your computer, see the table on page 1-37.
3 Add this plotter to the device list in the software.
This list may be accessed, for example, through CONFIG / Add a Plotter (in
AutoCAD), Printer setup (in Microsoft Windows applications) or Printer type (in
Macintosh applications). In most cases, you don’t need to add the plotter for each
individual software application, but, for example, just once for all Microsoft
Windows applications.
4 Configure the driver.
This usually involves a series of dialog boxes where you can specify such items as
default media type, print quality etc.
IMPORTANT
In most cases these settings will override any settings you make on the front panel
of the plotter.
1-36
Setting Up the Plotter
Task 9: Set Up Your Software
Software and Accessories Supplied with this Plotter, or Available
as an Option
Use the information in the table below to decide if you need to install and set up
any of the software supplied with this plotter. If you don’t know whether your
application sends PostScript files to the plotter (and therefore whether the plotter
may require the PostScript Upgrade Kit), consult your application software and its
documentation.
Item
For use
on
Supplied
or optional
Installation
Drivers for AutoCAD
PC
Supplied
Install the software on your
computer.
Driver for Microsoft
Windows 95 and 3.1
Applications
PC
Supplied
Install the software on your
computer.
1
PostScript
Upgrade Kit
PC
Optional
Optional
Install the firmware in your
plotter.
Macintosh
Install the software on your
computer.
HP JetDirect
Print Server
PC
Install the hardware in your
plotter.
Macintosh
Unix
Install the software on your
computer.
1
These items are updated from time to time. For details of which software
versions are supported, see the documentation included with them.
1-37
Setting Up the Plotter
Task 9: Set Up Your Software
Other Applications
If you are going to use applications other than AutoCAD or Microsoft Windows
applications, first check any Software Application Notes supplied with this plotter,
to see if the application is covered there. If not, here is some general advice:
The device list in your software may not be up to date with the latest plotters
available. If the HP DesignJet 700 or HP DesignJet 750C Plus is not quoted by
name in your application’s device list, select an alternative plotter as follows:
Preference Device
Comments
1
2
3
HP DesignJet 750C or
HP DesignJet 755CM
HP DesignJet 350C or
HP DesignJet 330
HP DesignJet 250C or
HP DesignJet 230
4
5
HP DesignJet 220
HP DesignJet 650C
With a preference for
C2858B/C2859B rather than
C2958A/C2859A
6
7
HP DesignJet 200
HP DesignJet 600 or
HP DesignJet
8
9
HP-GL/2 Device
or a similar option including a
reference to HP-GL/2
HP 7600
10 HP 7595B DraftMaster SX or
HP 7596B DraftMaster RX or
HP 7599A DraftMaster MX or
HP 7595C DraftMaster SX Plus or
HP 7596C DraftMaster RX Plus or
HP 7599B DraftMaster MX Plus
11 HP 7586B
If you choose these devices
you may not be able to use
your plotter’s parallel
connection – depending on
the application software.
12 HP 7580 or
HP 7585
The devices in the gray boxes support only HP-GL. The others support HP-GL/2
and HP-GL.
1-38
Setting Up the Plotter
Task 10: Print a Test Plot
Task 10: Print a Test Plot
The sample plots explained in task 6 simply verify the operation of the plotter
itself. Having connected the plotter to your computer and configured the drivers or
other software for your requirements, you should now be in a position to send a
test plot using one of your own files.
Among the points you should be looking out for are:
Did the Receiving light on the front panel come on?
Do you see any error message on the front-panel display?
Does the image appear in the size, orientation and position on the sheet that you
expected?
Is any of the image clipped?
Are the lines of the correct width?
Are the colors an exact representation of what you expected?
750C Plus
If you find any problem at all, start by consulting chapter 9 of this manual,
“Troubleshooting.” There you will find advice on many different types of
problems, from obtaining no plot at all, to tracking down the reason for a specific
print-quality issue. In case you do not solve your problem with the information
supplied there, chapter 9 also contains advice on where else to turn for help.
1-39
Setting Up the Plotter
Extra Tips For UNIX Users
Extra Tips for UNIX Users
Which Interface?
You can connect the plotter to your workstation in one of two ways:
Via the UNIX print-spooling system, using any of the interfaces: network,
parallel or serial
Directly using the serial interface
Recommendations
The print-spooling system is recommended, so that printing takes place in the
background while you continue using your application. A Print Server is also
recommended, as it will give you not only more flexibility in locating the plotter,
but also the possibility of network integration and centralized plotter
configurations using BOOTP (Bootstrap Protocol) and TFTP (Trivial File Transfer
Protocol).
If you choose the parallel interface, you may need a parallel interface card for your
workstation. Contact your workstation supplier for details.
1-40
Setting Up the Plotter
Extra Tips For UNIX Users
Print Spooler Configuration Examples
Example 1: Configuring the SunOS 4.1.3 Print Spooler for Sun SPARCstations
(parallel interface)
In order to perform the following steps you must be a superuser.
1 Create a directory for print spooling. All application users need read and write
permission for this directory. For example, from the command line of a shell, type
mkdir /usr/spool/cad
chmod 777 /usr/spool/cad
2 Edit the /etc/printcap file to set up the plotter configuration. You must assign a
name to each printer or plotter managed by the print spooler. Refer to the example
below if you need help completing this step.
Add these lines to your /etc/printcap file if:
your plotter is named djet,
the device name of your parallel port is /dev/bpp0, and
your spool directory is called /usr/spool/cad.
# Entry for an HP plotter on a parallel port
djet:\
:mx#0:sf:sh:\
:lp=/dev/bpp0:\
:sd=/usr/spool/cad:\
:lf=/usr/adm/lpd–errs:
1-41
Setting Up the Plotter
Extra Tips For UNIX Users
Example 2: Configuring the SunOS 4.1.3 Print Spooler for Sun SPARCstations
(serial interface)
In order to perform the following steps you must be a superuser.
1 Create a directory for print spooling. All application users need read and write
permission for this directory. For example, from the command line of a shell, type
mkdir /usr/spool/cad
chmod 777 /usr/spool/cad
2 Edit the /etc/printcap file to set up the plotter configuration. You must assign a
name to each printer or plotter managed by the print spooler. Refer to the example
below if you need help completing this step.
3 Add these lines to your /etc/printcap file if:
your plotter is named djet, and
your plotter is connected to the device named /dev/ttya (usually the first serial
port on the workstation), and
the spooling directory you created in step 1 is called /usr/spool/cad.
# Entry for an HP plotter on a serial port
djet:\
:lp=/dev/ttya:sd=/usr/spool/cad:br#9600:\
:lf=/usr/adm/lpd–errs:\
:sf:sh:mx#0:xc#0177777:xs#040040:fc#050:\
:ms=–evenp:
4 Make sure the plotter’s baud rate is 9600 and parity is even.
Example 3: Configuring the SunOS 4.1.3 print spooler for Sun SPARCstations
(HP JetDirect Print Server)
See the Configuration Guide shipped with the HP JetDirect Print Server.
1-42
Setting Up the Plotter
Extra Tips For UNIX Users
Example 4: Configuring the Solaris 2.x Print Spooler for Sun SPARCstations
In order to perform the following steps you must be a superuser or belong to the
special sysadmin (GID=14) group. If you are using the NIS+ name service, you
may need NIS+ permission to modify the printer table. Refer to your Sun
documentation for details.
1 Create a directory for print spooling. All application users need read and write
permission for this directory, so you must be a superuser to perform this step. For
example, from the command line of a shell, type:
mkdir /usr/spool/cad
chmod 777 /usr/spool/cad
2 Start the Administration Tool utility (from OpenWindowst).
% /bin/admintool
3 Load the Printer Manager window, and, from the Add Printer edit menu, select Add
Local Printer.
4 In the Add Local Printer dialog box:
Item
Select
Printer Name:
For example,HP DesignJet 700 or
HP DesignJet 750C Plus, depending on the plotter you have
purchased
Printer Type:
File Contents:
Banner:
Other, and set it to Unknown
Any
Not required
For full details on how to use the Printer Manager option of admintool, consult your
Sun documentation.
5 Exit admintool.
6 For serial connections:
a Make sure the plotter’s baud rate is 9600 and parity is even.
b From the command line of a shell, as superuser, enter the following:
lpadmin –p pname –o ”stty=’9600 evenp –cstopb ixon ixoff’”
where pname is the same as Printer Name in step 4. It is assumed that /usr/sbin
is in the superuser’s path.
1-43
1-44
2
The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
The Display Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Printing the Menus Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Description of the Menus Plot . . . . . . . . . . . . . . . . . . . . . . 2-5
Entering the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Navigating the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Menu Graphics Used in This Manual . . . . . . . . . . . . . . . . 2-9
Other Types of Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Example 1: Changing Margins . . . . . . . . . . . . . . . . . . . . . 2-11
Example 2: Changing the Drying Time . . . . . . . . . . . . . . 2-12
Learning How To Use the Front Panel
Display
Tutorial
2-1
Learning How To Use the Front-Panel Display
The Front Panel
The Front Panel
The front panel of the HP DesignJet 700 and 750C Plus plotters is shown below:
Display section
700
Status lights
Plotting mode keys
Action keys
Display section
750C Plus
Status lights
Plotting mode keys
Action keys
2-2
Learning How To Use the Front-Panel Display
The Front Panel
The purpose of this tutorial is to explain the use of the display section. The other
sections and their use are described later in this manual.
The display section is used primarily for setting the plotter’s configuration, so,
before the tutorial, print the current configuration. You can then return to this
afterwards.
1 Make sure that media is loaded. See page 3-10 for loading information.
2 Print the Current Configuration plot, by pressing the ° and ± keys
simultaneously.
Previous
STATUS
Press these two
simultaneously
Ready
Enter
Keep the plot for later reference.
The Display Section
The display section of the front panel consists of the display itself and the four
display keys to its right (Previous, ↑, ↓ and Enter).
Previous
STATUS
Display keys
Ready
Enter
2-3
Learning How To Use the Front-Panel Display
The Front Panel
The display can show two lines of text and is used for displaying:
S Menus, for example
Menu title
UTILITIES
Menu mode=short³
Menu option
In this case, you can use the display keys to navigate the menu system
and select menu options.
S Messages, for example
Load error
Remove media
These messages may concern machine status, actions required or
errors.
In this case, you can use the display keys to respond to messages.
See chapter 10, “Front panel messages” for more information.
2-4
Learning How To Use the Front-Panel Display
Printing the Menus Plot
Printing the Menus Plot
You can see the complete menu structure available on the plotter by printing the
Front Panel Menus plot. To help you understand the menu structure and how to
navigate it, print it now
1 Check that media is loaded. See page 3-10 for loading information.
2 Select the Menu option from the DEMO PLOTS menu, as described in chapter 1,
task 6. The Front-Panel Menus plot will be printed.
Description of the Menus Plot
Look at the Front-Panel Menus plot . It shows the full menu structure. Here is a
sample section of it (concerned with pen settings):
1
2
3
4
5
6
There are six columns:
1 contains the highest level
menu options.
6 contains the lowest level
menu options.
A
Row associated with
first level menu A
(Pen settings).
Area expanded for use in
the navigation example
on page 2-8.
2-5
Learning How To Use the Front-Panel Display
Entering the Menu System
Entering the Menu System
With a STATUS screen displayed, for instance:
STATUS
Ready
press the Enter key.
Either the SHORT MENUS screen:
SHORT MENUS
Queueing & Nesting
Only menus shaded yellow in Front
Panel Menus plot accessible (Shaded
gray if printing in black only).
or the FULL MENUS screen:
FULL MENUS
Queueing & Nesting
All menus accessible.
1
is displayed, with the Queueing & Nesting option shown.
Change to full menu mode, if necessary. See page 1-31.
You are now in the first level menu, shown in the first column of the Front
Panel Menus plot.
1
You may not be able to access the menu system immediately, if the current task overrides
it. If this happens, wait until the task is completed and try again.
2-6
Learning How To Use the Front-Panel Display
Navigating the Menu System
Navigating the Menu System
Once in the first-level menu, you navigate the system using the display keys.
Press Previous to display the previous menu level, without
changing any menu selections (equivalent to moving left [²]
1
one column in the Front-Panel Menus plot).
Press ° to scroll up, or ± to scroll down
through the options in a menu (equivalent
to moving up [°] or down [±] a column in
the Front-Panel Menus plot).
The option list is continuous, allowing you
to move from the bottom to the top by
pressing ± or from the top to the bottom
by pressing °.
Press Enter to:
a select an option and move to the next menu level, when in
the menu system (equivalent to moving one column to the
right [³] in the Front-Panel Menus plot).
b add to the configuration, your displayed choice from the options
available in the lowest level menu [¼].
1
The colored arrows °±²³¼, shown in square brackets above, are used to represent
pressing the relevant keys once, in the following navigation example.
2-7
Learning How To Use the Front-Panel Display
Navigating the Menu System
Use this example to practice navigating the menu system. It assumes that
you have entered the menu system from the STATUS screen and wish to
change the Merge setting in Pen settings. The colored arrows on the
excerpt of the Front-Panel Menus plot below correspond to the numbered
instructions.
1 Press the ± key five times to display the Pen settings option.
2 Press the Enter key to select the option and move to the Pen settings
second-level menu. The Palette option is displayed.
3 Press the ± key once to display the Merge option.
4 Press the Enter key to select the option and move to the Merge
third-level menu. The option currently selected is displayed with a *.
5 Change the displayed option by pressing the ± or the ° key.
6 Press the Enter key to set Merge equal to the new displayed value. You
will be returned to the Merge second-level menu.
7 To exit the menu system, press the Previous key twice.
If you now re–enter the menu system and repeat steps 1 to 4, you will see
the option that you selected displayed with a *.
±
1
±
Software*
Palette A
Palette B
Factory
±
Palette=³
±
±
±3
Off*
±°
5
Merge=³
Pen settings³
¼
6
³
2
On
³
4
²
7
²
Palette A³
Palette B³
Factory³
7
Define palette³
Note: A ³ character in a menu option box indicates that another level of
menu is available.
2-8
Learning How To Use the Front-Panel Display
Navigating the Menu System
Menu Graphics Used in this Manual
At the end of this chapter, there are some examples of navigating the menu system,
showing all the menu displays available. In the rest of this manual, when you need
to use the menu system, a simple menu graphic will appear in the left margin
giving a concise explanation of how to navigate to the exact place.
The graphics look similar to this, but further levels may be shown:
First column selection
Second column selection
Represents pressing Enter
Full menu mode
Default: 0
Affects next plot sent
Stays after power off
Menu mode required, and other useful
information for item
2-9
Learning How To Use the Front-Panel Display
Other Types of Screen
Other Types of Screens
Other screen, such as those displayed for selecting media type during media
loading:
SELECT MEDIA
Opaque bond
or for changing the language:
LANGUAGE
English
are in fact further examples of selection menus which are not part of the
main menu system. These behave in the same way as other menus, in that
you can scroll through the options using the ± and ° keys and select a
displayed option using the Enter key.
2-10
Learning How To Use the Front-Panel Display
Examples
Examples
Example 1: Changing Margins
In the section of this manual that describes how to adjust the page margins, the
icon on the left is shown, indicating that you should go to the MARGINS menu as
follows.
Page format
Margins
Full menu mode
Default: Normal
Affects next plot
With the STATUS screen displayed:
STATUS
Ready
1 Enter the menu system by pressing the Enter key.
Either the SHORT MENUS screen or the FULL MENUS screen is
displayed with the Queueing & Nesting option. If necessary, see page
1-31 and change to full menu mode.
FULL MENUS
Queueing & Nesting
2 Press the ° key once, or the ± key 6 times, to display the required option.
FULL MENUS
Page format³
3 Press the Enter key.
PAGE FORMAT
Size=ISO³
Continued...
2-11
Learning How To Use the Front-Panel Display
Examples
4 Press the ± key twice, or the ° key twice, to display the required option.
PAGE FORMAT
Margins=Normal
5 Press the Enter key to display the MARGINS menu.
MARGINS
Normal
6 Use the ↑ and ↓ keys to display the available options and, when the one
required is displayed, press the Enter key to select it as the value for
Margins.
Example 2: Changing the Drying Time
The section on adjusting the drying time, to suit different environmental
conditions, contains the icon shown on the left, indicating that you should go to the
DRYING TIME menu. This example assumes that the display is in full menu mode
following example 1, but can be used in short menu mode.
Device setup
Drying time
Both menu modes
Default: Normal
With the STATUS screen displayed
STATUS
Ready
1 Enter the menu system by pressing the Enter key.
The FULL MENUS screen is displayed with the Queueing & Nesting
option.
FULL MENUS
Queueing & Nesting
Continued...
2-12
Learning How To Use the Front-Panel Display
Examples
2 Press the ° key 3 times, or the ± key 4 times, to display the required option.
FULL MENUS
Device setup³
3 Press the Enter key. (If the display is in short menu mode, you will
notice that the screen shown after instruction 4 below is displayed at
this point, so go to instruction 5.)
DEVICE SETUP
Lang=7586, HP–GL/2³
4 Press the ° key once, or the ± key 4 times, to display the required option.
DEVICE SETUP
Drying time=Normal³
5 Press the Enter key to display the DRYING TIME menu.
DRYING TIME
Normal*
6 Use the ↑ and ↓ keys to display the available options and, when the one
required is displayed, press the Enter key to select it as the value for
Drying time.
2-13
2-14
3
Choosing Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Caring For Your Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Loading Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Unloading Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Replacing Cartridge(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Working With Media and Cartridge(s)
3-1
Working With Media and Cartridge(s)
Choosing Media
Choosing Media
Your plotter supports many types of paper and other media types. Choosing the
best media type for your requirements is the first (and most important) step in
ensuring good print quality. It is recommended you only use genuine
Hewlett-Packard media, whose reliability and performance have been developed
and thoroughly tested to give trouble-free performance and optimal print quality.
For details of Hewlett-Packard media, see page 3-3 and the HP DesignJet Papers
and Films catalog supplied with the plotter.
Five Important Points about Media Types
When selecting different opaque paper types, be aware that you will use
significantly less ink printing on coated types than on normal opaque bond.
Most media types are supported , However the quality of some plots may not be as
good if you do not use HP media. For media details, see the table on page 3-5.
Whenever you load a roll or a sheet, the plotter’s front-panel display prompts
you to specify which media type you are loading. It is absolutely essential for
good print quality to specify this correctly. The table on page 3-3 gives you all
the information you need. If media is already loaded and you are unsure which
media type was specified, go to Utilities / Statistics in the front panel, as
explained on page 7-2.
You should also be aware of which print quality setting (best, normal or fast)
you are using. You can set this either from your software or from the plotter’s
front panel (the software driver setting will override any print quality setting
made on the front panel). The combination of media type and print quality
settings automatically tells the plotter how to place the ink on the media – for
example, in terms of ink density and number of passes of the cartridge(s). For
more details, see the tables on page(s) 3-6 and 3-7. There are print quality
improvements which can be made using Sharp lines on the front panel menu or
in the Windows, this is described on page 5-14.
Included with this plotter is a HP DesignJet Papers and Films catalog which
gives ordering details for Hewlett-Packard media supplies. To get the latest
version of this document, contact your local HP Sales and Support office.
3-2
Working With Media and Cartridge(s)
Choosing Media
Supported Media Types
Media Type on the
Front-Panel Display
1
Also Known As
Commercial Name of HP Media
Opaque bond
Plotter paper
HP Opaque Bond
Translucent bond
Natural tracing paper
HP Translucent Bond
HP Natural Tracing Paper
Natural tracing paper
Tracing paper
Extra translucent bond
Vellum
HP Vellum
Coated paper
Special paper
HP Coated Paper
Special inkjet paper
Color inkjet paper
Matte paper
Note: HP Special Inkjet Paper is not
supported on the HP DesignJet 700
plotter.
Presentation
700
Heavy coated paper
Heavyweight coated paper
Heavyweight special paper
Heavyweight inkjet paper
Heavyweight color inkjet paper
Heavyweight matte paper
HP Coated Heavyweight Paper
Note: HP Heavyweight Special
Inkjet Paper is not supported on the
HP DesignJet 700 plotter.
700
Matte film
Matte polyester
Poly matte film
Mylar
HP Matte Film
Clear film
Translucent film
HP Clear Film
Clear polyester
High-gloss photo
High-gloss photo paper
High-gloss paper
HP High-Gloss Photo Paper
HP Semi-Gloss Photo Paper
HP High-Gloss White Film
750C Plus
Semi-gloss photo
Semi-gloss photo paper
Semi-gloss paper
High-gloss white film
750C Plus
High-gloss film
750C Plus
1
From time to time, new media types may become available. For up-to-date information, please contact
your HP dealer or local HP Sales and Support Office.
3-3
Working With Media and Cartridge(s)
Choosing Media
Physical Characteristics of Media Types
Physical Characteristics
Media Type on the
Front-panel Display
Opacity
Matte or
Glossy
Special coated
side for plotting?
Opaque bond
Translucent bond
Natural tracing paper
Vellum
Opaque
Matte
No
No
No
No
Semi-opaque Matte
Semi-opaque Matte
Semi-opaque Matte
1
Coated paper
Heavy coated paper
Matte film
Opaque
Opaque
Matte
Matte
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Semi-opaque Matte
Clear film
Clear
–
High-gloss photo
Semi-gloss photo
High-gloss film
1
Opaque
Opaque
Opaque
Glossy
Glossy
Glossy
750C Plus
When loading coated paper into the plotter, ensure the coated side is facing
downwards.
3-4
Working With Media and Cartridge(s)
Choosing Media
Cost and Color Support of Media Types
750C Plus
Media Type on the
Front-panel Display
Cost (Relative to
Each Other)
Recommended for
Color?
1
Opaque bond
Translucent bond
Natural tracing paper
Vellum
Low
CAD drawings only
No
Low
1
Moderate
Moderate
Low / moderate
Moderate
High
CAD drawings only
HP media only
Coated paper
Heavy coated paper
Matte film
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Clear film
High
High-gloss photo
Semi-gloss photo
High-gloss film
1
High
High
High
The limitations using non-coated media for color depends on:
the amount of filled area in your drawing (the more there is, the less likely that
the print quality on opaque bond will be satisfactory),
the quality of the media.
3-5
Working With Media and Cartridge(s)
Choosing Media
Combinations of Media Type and Print Quality
The table below shows that some combinations of media type and print quality are
not recommended.
Media Type on the
Front Panel Display
Print Quality
(Set Either on the Front Panel or In the Software)
Fast
OK
Normal
OK
Best
OK
Opaque bond
Translucent bond
OK
OK
OK
700
Translucent bond
OK
OK
OK
in monochrome
in monochrome
in monochrome
750C Plus
only
only
only
Natural tracing paper OK
OK
OK
OK
OK
Vellum
OK
OK
Coated paper
OK
OK
OK
OK
Heavy coated paper
Matte film
OK
OK
OK
OK
OK
Clear film
OK
OK
High-gloss photo
Not
OK
OK
OK
OK
750C Plus
750C Plus
recommended
Semi-gloss photo
High-gloss film
Not
OK
OK
recommended
Not
750C Plus
recommended
IMPORTANT
If you are using an add-on a third-party Raster Image Processor (RIP), in order to
create additional print modes on your plotter, then the above table may not apply.
In this case, consult your RIP vendor for advice on the best settings for your re-
quirements. A clue as to whether you are using a RIP or not is the message on the
plotter’s front panel while it is printing. If the message “STATUS / Printing (spe-
cial)” appears, then you are using a RIP. If the message “STATUS / Printing”
appears, then you are probably not using a RIP.
3-6
Working With Media and Cartridge(s)
Choosing Media
Typical Media Type Choices by Application
2
Application
Use
Typical Choice of Media
Probable Choice of
Print Quality
3
1
CAD
Drafts
Opaque bond
Translucent bond
Natural tracing paper
Vellum
Fast or Normal
Fast or Normal
Fast or Normal
Fast or Normal
Final versions
Archives
Opaque bond
Matte film
Clear film
Normal or Best
Normal or Best
Normal or Best
700
Vellum
Matte film
Clear film
Best
Best
Best
Diazo reproductions
Translucent bond
Natural tracing paper
Vellum
Normal or Best
Normal or Best
Normal or Best
Normal or Best
Matte film
1
2
CAD = Computer-Aided Design
Using the generic media types on the front-panel display
Set either on the front panel or in the software
3
3-7
Working With Media and Cartridge(s)
Choosing Media
2
Application
Use
Typical Choice of Media
Probable Choice
of Print Quality
3
1
Drafts
Opaque bond
Translucent bond
Natural tracing paper
Vellum
Opaque bond
Matte film
Fast or Normal
Fast or Normal
Fast or Normal
Fast or Normal
Normal or Best
Normal or Best
Normal or Best
Best
CAD
monochrome
Final versions
Archives
Clear film
Vellum
Matte film
750C Plus
Best
Clear film
Best
Diazo reproductions Translucent bond
Normal or Best
Normal or Best
Normal or Best
Normal or Best
Fast or Normal
Fast or Normal
Fast or Normal
Fast or Normal
Normal or Best
Normal or Best
Normal or Best
Fast or Normal
Natural tracing paper
Vellum
Matte film
1
1
Drafts
Opaque bond
Natural tracing paper
Vellum
CAD and GIS
color
Coated paper
Coated paper
Final versions
Heavy coated paper (for
durability)
Matte film
750C Plus
Clear film
Archives
Matte film
Best
Clear film
Normal
Overlays
Matte
Clear film
Fast or Normal
Imaging and graphics
package(s)
color
Opaque bond (for drafts)
Coated paper
Heavy coated paper (for
durability)
Fast, Normal or
Best
Fast, Normal or
Best
Normal or Best
Gloss
High-gloss photo
Semi-gloss photo
High-gloss film
Normal or Best
Normal or Best
Normal or Best
750C Plus
Clear film
Clear film
Best
1
2
CAD = Computer-Aided Design
Using the generic media types on the front-panel display
Set either on the front panel or in the software
3
GIS = Geographical Information or Mapping Systems
3-8
Working With Media and Cartridge(s)
Caring For Your Media
Caring For Your Media
Handle film and glossy media by the edge(s) or wear cotton gloves. Skin oils
can interact with ink and cause your plot to smear.
Make sure the media bin is installed between the plotter’s legs. When the
plotter finishes each plot on roll media, it automatically cuts the plot and drops
it into the bin. Note that mixing plot sizes can cause shorter plots to curl and
shuffle in the bin.
Colors may eventually fade or change when exposed to office light or sunlight
over a period of time. Therefore:
– avoid exposing your plots longer than necessary to direct sunlight.
750C Plus
– ideally, when not using your plots, store them away from any light, for
example, in a drawer.
3-9
Working With Media and Cartridge(s)
Loading Media
Loading Media
To Change a Roll
1 Make sure the plotter wheels are locked (the brake lever pressed down) to prevent
the plotter from moving.
2
If the old roll is not used up, then to remove the media from the media path:
a Raise the media lever to release the media.
b Open the roll cover and turn the media stop to wind the media out of the
plotter and onto the roll.
Raise the lever
Wind the roll
c Lower the media lever.
1840a
3-10
Working With Media and Cartridge(s)
Loading Media
3
Remove the old roll of media by pulling firmly on each end of the spindle.
B
A
1837a
4
a Rest the old roll upright on the floor so that the media stop (A) is on top.
b Pull out the media stop and the spindle and set it aside.
A
0021
3-11
Working With Media and Cartridge(s)
Loading Media
5
From the other end of the old media roll, pull out the endcap (B).
B
0022
6 If you are not immediately loading another roll of media into the plotter, replace
the endcap on the spindle and place the spindle back in the plotter. You can skip
the rest of these steps.
7
a Remove the new roll from its wrapping.
b Turn the spindle upside down, that is, with the media stop at the bottom (and
the end cap still removed)
c Place the new roll on the spindle, so that the leading edge winds clockwise.
Endcap removed
If the media stop falls off, push it back
in until it snaps into position.
A
0015
3-12
Working With Media and Cartridge(s)
Loading Media
8
Push the endcap back in, making sure that the tabs are flush against the ends of
the roll. Push it far enough to be firm, but do not use excessive force as this
may result in broken tabs.
B
0016
9
Insert the spindle so that the media stop (A) is to the right and the endcap (B)
to the left. Push in firmly on both ends. Make sure the media remains flush
against the media stop.
B
A
A
Media path
0017
The media should wind up from behind the roll.
1837
10 Check the leading edge as it unwinds from the spool. If it is uneven, trim it as
explained in step 11. Otherwise go to step 12.
3-13
Working With Media and Cartridge(s)
Loading Media
The media cutting knife used in the next step is sharp. Make sure the plotter’s
wheels are locked. Keep fingers clear of the cutting path. Keep media cutting
knife away from children.
W A R N I N G
11
To trim the leading edge of the media roll:
a Pull the media over the top of the plotter and lay it over the cutting track.
b Use the media cutting knife in the pocket located at the back of the
plotter to cut off the first few inches of the media.
c Retract the blade and return the media cutting knife to its pocket.
1838
3-14
Working With Media and Cartridge(s)
Loading Media
12
a Pull the media up and, holding it from the sides, align its right edge with
the perforated line on the entry platen.
b Insert the leading edge into the plotter, until the page buckles slightly.
c Release the media when the plotter begins to pull it in.
1839
13
Press the ↓ key next to the front-panel display to indicate you are loading roll
media.
↑
Sheet load
Roll load
––––––––>
––––––––>
↓
0014
3-15
Working With Media and Cartridge(s)
Loading Media
14
Use the ↑ and ↓ keys until the display shows the type of media you are
1
loading , and then press the Enter key.
↑
SELECT MEDIA
Coated paper
↓
Enter
If you are using software that offers a “special print mode” for this plotter, then
simply press Enter on the first media type displayed (whatever it is), as in this
case it is the software that controls the print mode, not the plotter. For more
details on special print modes, see page 3-6.
0014
15
a When the front panel instructs you, lift the media lever.
b Take hold of the edge(s) of the media, now extending from the exit slot,
and pull the media toward you until taut. Then align the left and right
edge(s) of the media, so that they are flush with the edge(s) of the roll.
A
B
c When the front panel instructs you, lower the media lever.
0018
1
For advice on media types, see page 3-2.
3-16
Working With Media and Cartridge(s)
Loading Media
16
a When the plotter instructs you to close the roll cover, rewind the media stop
in the direction shown by the large arrow below, to take up any slack in the
roll. Make sure the leading edge of the media is outside the roll cover, and
then close the cover.
b Press ↓ to continue. The plotter trims off the first few inches of media.
1840
3-17
Working With Media and Cartridge(s)
Loading Media
To Load a Sheet
Which way round?
You can load a sheet in either portrait or landscape orientation. Unless using
the Rotate option (see page 4-7), load the sheet in the same orientation as you
have specified in your software.
or
Which way up?
As you load the sheet, it is the under side on which the plotter will print. With
most media types, the two sides are different and so it is important to load the sheet
correctly. Refer to the table below.
Media Type
Media-Loading Tips
Opaque bond
Both sides are the same. If the sheet is curled,
load with the curve (hollow) side towards you.
Translucent bond
Natural tracing paper
Vellum
Coated paper
Load with the coated side down.
Heavy coated paper
On HP Coated Paper and Heavyweight Coated
Paper, look for the small notch in the corner:
When loading in a portrait orientation, make
sure the notch is on the right side of the leading
edge.
When loading in a landscape orientation, make
sure the notch is on the left side of the leading
edge.
Matte film
Clear film
Load with the matte side down.
Load with the rougher side down.
Load with the glossy side down.
High-gloss photo paper
Semi-gloss photo paper
High-gloss film
750C Plus
3-18
Working With Media and Cartridge(s)
Loading Media
1 If you need to, unload any roll media, see page 3-10.
2 Make sure the media lever is down and the roll cover is closed.
3
a Holding the media from the sides, align the right edge with the
perforated line on the entry platen.
b Insert the media until it buckles slightly. That is, push all the way to
the media stops. Let go of the media when the plotter begins to pull it
in.
1841
4
Press ↑ next to the front-panel display to indicate you are loading a sheet.
↑
Sheet load
Roll load
––––––––>
––––––––>
↓
0014
3-19
Working With Media and Cartridge(s)
Loading Media
Scroll until the display shows the type of media you are loading*, and then
5
press the Enter key.
↑
SELECT MEDIA
Opaque bond
↓
Enter
*For advice on media types, see page 3-2.
0014
6 The plotter moves the sheet in and out to check its size and alignment, then
advances it to the start of the page. When sheet loading is complete, the “STATUS /
Ready” message is displayed.
3-20
Working With Media and Cartridge(s)
Loading Media
Compensating for Badly Cut Media
You can only use this feature when sheet media is selected on the front panel.
If the media is persistently difficult to load, it could be an indication that it has
been badly cut. That is, it has been cut unevenly with the media width on the
leading edge different to the width of the trailing edge. A front-panel option called
Skew tolerance helps you compensate for the shape of some poorly cut media.
When you properly load the leading edge of badly cut media along the perforated
line on the platen, you may notice the trailing edge is displaced from the line by a
small distance and the plotter will not accept the media. The plotter can accept
poorly cut media that is displaced 1.0 cm or less from the perforated line.
Media that is cut properly should not need the help of the skew tolerance feature.
In fact, using this feature for properly cut media increases the risk of skewing your
plot on the page.
To Adjust Skew Tolerance
Skew Tolerance
In Front Panel
Maximum Acceptable Skew of Loaded Sheet
Device setup
Skew tolerance
Off
On
0.4 cm
1.0 cm
Full menu mode
Default: Off
Resets after power off
3-21
Working With Media and Cartridge(s)
Unloading Media
Unloading Media
Drying Time
On some media types the ink needs to dry before the plot is unloaded. For roll
media the plotter automatically allows the appropriate drying time before cutting
the plot and dropping it into the media bin. For sheet media you should wait for
the times shown in the table below before unloading the plot.
Typical Drying Times (minutes)
Print Quality
Media Type on the
Front Panel Display
Fast
Normal
or Best
Opaque bond
Translucent bond
Natural Tracing paper
Vellum
0.5
0.5
0.5
1.0
0
1.0
1.0
1.0
2.0
0.25
0.25
2.0
2.0
4.0
4.0
4.0
Coated paper
Coated heavy paper
Matte film
0
Not
recommended
Clear film
High-gloss photo
Semi-gloss photo
High-gloss film
Not
750C Plus
recommended
In the table above you will see that some media types can be unloaded
immediately.
3-22
Working With Media and Cartridge(s)
Unloading Media
To Adjust Drying Time
You can make a global adjustment to the plotter’s automatic drying times through
the front-panel menus.
Drying Time Selected
in Front Panel
Result
Device setup
Drying time
None*
Less
The plotter cuts plot without delay.
Adjusted for the driest expected environmental
conditions.
All menu modes
Default: Normal
Normal
More
As described in the table on page 3-22
Adjusted for the most humid expected environmental
conditions.
* Not recommended if you are using roll media and leaving the plotter unattended, as the ink
may smear when the plots are dropped into the media bin.
If you are operating your plotter in an extremely dry environment, select Less in
the front panel menu. In an extremely humid environment, select More. For
environmental specifications, see page 11-4.
IMPORTANT
Adjusting drying times purely to speed up the plotter is not recommended as the
quality of your plot can be impaired.
3-23
Working With Media and Cartridge(s)
Unloading Media
To Unload a Sheet After Plotting
1 Wait until the appropriate drying time has passed (see table on previous page – no
drying time is necessary for some media types).
2
Gently pull the sheet out from the plotter.
1842
3-24
Working With Media and Cartridge(s)
Unloading Media
To Remove an Unused Sheet
Either ...
1 Press Form Feed and Cut.
2 When the plotter has finished feeding it out, pull out the sheet.
Form Feed
and Cut
1842a
or ...
1 Lift the media lever.
2 Pull out the sheet.
3 Lower the media lever.
1842b
3-25
Working With Media and Cartridge(s)
Replacing Cartridge(s)
Replacing Cartridge(s)
When to Replace Cartridge(s)
Note that your HP DesignJet 700 contains only one black cartridge.
700
Note that your HP DesignJet 750C Plus has three color and one black cartridge(s).
Replace the cartridge(s) in the following three circumstances.
750C Plus
1 When the plotter prompts you to replace one or more cartridge(s)
(by displaying Service cartridge(s) on the front panel).
The plotter automatically checks before and after every plot that the cartridge(s)
are seated correctly and that the nozzles are working, this is called automatic
checking. You can switch off the automatic checking using the front panel
menus.
Device setup
Cartridge check
Full menu mode
Default: On
Note that automatic checking does not check the ink levels.
2 When either poor print quality or the ink-level indicator on the cartridge indicates
that the cartridge is out of ink.
To check a cartridge’s ink level:
Green = full
A considerable portion of ink has been used.
Cartridge is close to empty.*
Black = empty
* It is recommended to have a replacement cartridge ready by this time.
Note: The ink-level indicator is not an exact gauge of the specific quantity
of ink available over the life of the cartridge.
0002
3 When you are troubleshooting print quality problems. See chapter 9, page 9-16.
3-26
Working With Media and Cartridge(s)
Replacing Cartridge(s)
Before Replacing Cartridge(s)
Four important points:
1 Your plotter is designed to operate only with the black cartridge whose specific part
700
number is listed on page 11-15.
Your plotter is designed to operate only with the four cartridge types whose
specific part numbers are listed on page 11-15. Except on glossy media types, the
plotter will operate successfully in monochrome with just the black cartridge
loaded, although the Best print quality may not be as good as if all cartridges were
loaded. Otherwise, all four must be loaded.
750C Plus
2 Every time you replace, or even adjust, a cartridge, the plotter afterwards runs an
automatic alignment procedure, for which it needs an opaque media type, for
example opaque bond (regular plotter paper) or coated paper. So make sure that
either a roll or a sheet of the appropriate media is loaded before you replace a
cartridge. If the automatic cartridge alignment procedure is not run on a suitable
media type, print quality will be affected.
3 Once the cartridge(s) have been installed they should not be removed, except to
replace them. This will ensure the best lifetime for your cartridge(s).
4 Make sure you are aware of the general warning and cautions below.
Don’t touch the stainless steel strip that runs the length of the plotter behind
the cartridge carriage; its edge is very sharp. Keep hair, jewelry, clothing,
and foreign objects away from the plotter mechanisms. Keep new and used
print cartridge(s) out of the reach of children.
W A R N I N G
Only touch the plastic parts of the cartridge. Do not touch, wipe, or attempt to
clean the cartridge nozzles or contacts as they can become clogged or
scratched and are easily damaged.
C A U T I O N
C A U T I O N
Each time you access the cartridge(s) to load or reseat them, the nozzles are
exposed to air. If the nozzles are exposed to air (except during plotting) for
more than a few minutes at a time, they are susceptible to clogging and
drying.
C A U T I O N
With the HP DesignJet 750C Plus plotter, it is absolutely essential to load the
cartridge(s) in the correct stalls, or your colors will be wrong and print quality
may be impacted.
750C Plus
3-27
Working With Media and Cartridge(s)
Replacing Cartridge(s)
To Replace a Cartridge
If you are responding to a Service cartridge(s) request, go straight to step 4.
1 Start with the plotter switched ON.
2 Make sure the front-panel display reads STATUS / Ready (not STATUS / Ready for
media).
a Press the Access Cartridge(s) key and wait for the cartridge carriage to
3
come to a complete stop next to the front panel.
700
750C Plus
Continued...
1849a
3-28
Working With Media and Cartridge(s)
Replacing Cartridge(s)
4
a When the carriage stops, open the window.
b Press down lightly on the cartridge you are replacing and pull it toward
you. Remove the cartridge from its stall and discard it.
Black
700
Yellow
Cyan
Magenta
Black
750C Plus
Notice that each stall in the carriage has a dot indicating the color: when
loading the new cartridge you must put the correct cartridge in the correct
stall.
For users with color-vision deficiencies: You can identify the colors of the
cartridges by the part numbers on the boxes – see page 11-15. The sequence
of the stalls is, from left to right, yellow, cyan, magenta and black.
Continued...
0019
3-29
Working With Media and Cartridge(s)
Replacing Cartridge(s)
1754
5
For each cartridge in the set that needs to be replaced:
a Take the new cartridge out of its box.
b Remove the colored protective tape and tab from the cartridge’s nozzles.
For the HP DesignJet 750C Plus, match the color of the
cartridge’s label with the color of the dot above the stall.
750C Plus
c Insert the cartridge in the correct stall. Press down lightly and push the
cartridge away from you until it snaps into place.
700
Yellow
Cyan
Magenta
Black
750C Plus
If the front-panel display says Reseat cartridge(s), then remove the cartridge
indicated in the display and insert it again. Do so until the message disappears.
0019
6 When you have finished installing the cartridge(s), the plotter runs the automatic
alignment procedure. When the front panel displays STATUS / Ready, the
procedure is complete. You can throw away the small print produced during the
alignment procedure.
3-30
4
Page Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Adjusting the Margins (Roll Media Only) . . . . . . . . . . . . . . . . . 4-6
Rotating a Plot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Plotting a Mirror Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Controlling the Page Format
Page Size, Margins and Other Controls
4-1
Controlling the Page Format
Page Size
Page Size
This chapter explains how to make sure that the plotter prints your plot in the page
size you want.
Terminology
Media
Page size
Margin
Plotting area
Inked area
0023
Page size
This can be specified from the front panel or in the software, where it may be
called ‘‘Page Size”, ‘‘Media Size”, ‘‘Paper Size” etc., and where the options
include, for example, ISO A3, ANSI Letter, Architectural E and Custom. If the
drivers setting is ‘‘default”, the front panel setting is used. Any other software
setting overrides the front panel setting, unless the latter is Inked area and you are
sending a PostScript file: in this case the front panel setting takes precedence.
When using the AutoCAD driver the “User Size” is the plotting area.
Margins
These are specific to the plotter and are normally 17 mm on the leading and trailing
edges and 5 mm on the sides. The 17 mm can be adjusted for roll media, as
explained on page 11-3.
Plotting area
This is the page size minus the margins. For a table showing the plotting areas for
standard media sizes, see page 11-6.
This is the smallest rectangle that contains the entire drawing, while maintaining its
relative dimensions.
4-2
Controlling the Page Format
Page Size
To save wasting media you can plot a page size equal to the inked area plus the
margins. This setting may be available in your driver, it can also be selected by
changing the front panel menu to “Inked area”.
Do You Need to Adjust the Page Size in the Front Panel?
Depending on the driver you are using, you may not need to change the page size
in the front panel. The default setting of the plotter looks to your software for the
page size settings: if it is there, the plotter uses it.
However, some of the circumstances in which you may want to change the default
setting are:
If you want to print the inked area only, but the driver you are using does not
specify “Inked area”.
In this case, set Page format / Size to Inked area.
Note: If you can select Inked area from your driver, any selection you have made
in the front panel menu will be overridden by the settings in the driver.
When the plots you are creating need to be of a specific standard (for example,
ISO or ANSI), but the actual size within that standard is not important. For
example, your page size may need to conform to a standard ISO page size, but it
does not matter whether the final page size is ISO A4 or ISO A3.
In this case, set Page format / Size to ISO > Best... or ANSI > Best ... etc. The
plotter uses the smallest standard size into which the inked area will fit.
4-3
Controlling the Page Format
Page Size
To Adjust the Page Size from the Front Panel
Size
In Front Panel
Comments
Page format
Size
Software
The plotter looks to the plot you have sent for
a page size instruction. If it is present the
plotter uses this. If not, the plotted page size
is the inked area plus margins.
All menu modes
Default: Software
Inked area
The plotted page size is the inked area plus
margins. For a definition of “inked area”, see
page 4-2.
ISO
Best ISO A
“Best ...” options
The plotter chooses the smallest page size
(from the A-series: A4, A3 etc.) that will hold
the inked area of the plot. For example, if the
inked area of the plot is between A3 and A4,
the plotter chooses A3 as the page size.
ISO A0/1/2/3/4
Best ANSI
ANSI
JIS
ANSI E/D/C/B/A
Best JIS B
Discrete options
ISO
ANSI
JIS
A0/1/2/3/4
E/D/C/B/A
B1/2/3/4
JIS B1/2/3/4
ARCH E1/E/D/C/B/A
Over A1/2
ARCH
Best ARCH
ARCH E1/E/D/C/B/A
The plotted page size is exactly the size you
specify. The largest discrete page size you
can specify depends whether your plotter is
an E-size or D-size model.
Oversize (No “Best” option)
Over A1/2
If you need to adjust the page size from the front panel, do so before sending the
plot file from your computer, as the plotter determines the size of a plot at the time
it is received from your application.
4-4
Controlling the Page Format
Page Size
Page Size and Clipped Plots
If you specify in your software a page size that is larger than the media size loaded
in the plotter, the plotter will still print what it can, but may clip your plot.
A2 media in the plotter
Clippedarea
A1 page size in software or front panel
Page Size and Nesting (Roll Media Only)
Nesting means placing two or more plots side-by-side on a roll to save media.
There are certain cases when your plots will not be nested, for a complete
explanation of nesting see page 6-10.
If you have queueing and nesting switched on, the plotter will use the page size to
determine which plots are nested and whether the plots can be automatically
rotated when nesting.
4-5
Controlling the Page Format
Adjusting the Margins (Roll Media Only)
Adjusting the Margins (Roll Media Only)
Besides nesting and setting the page size, you can also change the margin settings
and expand the plotting area of the page, therefore reducing the amount of media
waste. The two side margins are 5.0 mm. The automatic setting of the plotter’s
margins is 17 mm on the leading and trailing edges of the media. By reducing the
margins to 10 mm on the leading and trailing edges of the media, you can use
14 mm more plotting area along that axis. The adjustment is available in the front
panel.
Page format
Margins
Normal Margins
Smaller Margins
Trailing edge
Full menu mode
Default: Normal
Affects next plot
10 mm
17.0 mm
5.0 mm
5.0 mm
5.0 mm
17.0 mm
10 mm
Leading edge
5 mm = 0.2 in
10 mm = 0.4 in
17 mm = 0.67 in
0024
Margins and Automatic Cutting
IMPORTANT
When Margins is set to Smaller, the plotter waits for the plot to dry and the next
plot to begin plotting before cutting the plot from the roll. If you press Form Feed
and Cut, the plotter immediately cuts off the current plot. When the next plot
begins, the plotter cuts again to give this plot the narrow margin.
4-6
Controlling the Page Format
Rotating a Plot
Rotating a Plot
Rotating a Drawing from the Front Panel
Your Drawing can only be rotated from the Page format / Rotate option in the front
panel if:
Queueing and Nesting are off (see page 6-10), and
the file contains no raster data.
If you are using the Microsoft Windows driver supplied with this plotter, your files
do contain raster data and therefore you cannot use this Rotate option. The normal
line drawings of most CAD software do not contain raster data, and can use this
Rotate option.
To Rotate a Plot from the Front Panel
Except in the circumstances stated above, you can rotate a plot from the plotter’s
front panel, without changing the drawing in your software. The options are 90,
180 or 270 degrees relative to the drawing’s orientation in your software. The
rotation is counterclockwise, as shown below.
Page format
Rotate
0
90
180
270
Full menu mode
Default: 0
Affects next plot sent
Stays after power off
4-7
Controlling the page format
Rotating a plot
Exactly What Is Rotated?
With roll media, both the drawing and the page orientation are rotated.
0
90
180
270
A
A
Notice that the narrow margins are always at the side, regardless of the
orientation.
0025
With sheet media, the drawing is rotated, but the page orientation specified
in your software is retained. (You should always load sheet media in the
same orientation as you have specified in the software.)
0
90
180
270
A
A
0026
The Rotate Feature and Clipped Plots
With either roll or sheet media, if you rotate to landscape a plot whose original
orientation was portrait, it is possible that the media is not wide enough for the
drawing, and so it may be clipped. For example, rotating by 90 a portrait
D/A1–size plot on D/A1-size media will probably result in a clipped plot.
4-8
Controlling the Page Format
Rotating a Plot
How Does Rotate Interact with Your Software?
The plotter adds the rotation setting to any rotation angle you specify in your
software. For example:
For software applications which, like the plotter, rotate counter-clockwise (for
example, CorelDRAW!) the result is the sum. For example, if your software has
specified a rotation of 180 degrees, and you set Rotate in the front panel to 90,
your plot’s final rotation will be 270 degrees.
For software applications which rotate clockwise (for example, AutoCAD) the
result is the difference. For example, if your software has specified a rotation of
90 degrees, and you set Rotate in the front panel to 90, there will be no rotation.
For further information on the Rotate feature see page 9-21 in the Troubleshooting
chapter which details some of the most common problems.
4-9
Controlling the Page Format
Plotting a Mirror Image
Plotting a Mirror Image
You can plot a mirror image of the plot from the plotter’s front panel, without
changing the drawing in your software.
Page format
Mirroring
Mirror off
Mirror on
Full menu mode
Default: Off
Affects current plot
Resets after power off
Do not change the setting during a plot, as the change becomes effective
immediately; if you change the setting in the middle of the current plot, the
remaining data is plotted in the mirrored orientation.
4-10
5
Ways to Control the Plot’s Appearance . . . . . . . . . . . . . . . . . . . 5-2
Changing Pen Widths and Colors Using the Plotter’s Internal
Palettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Changing the Treatment of Overlapping Lines
(Merge Features) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Changing the Overall Lightness/Darkness of a Plot . . . . . . . . . 5-8
Printing Color Drawings in Monochrome . . . . . . . . . . . . . . . . . 5-9
Choosing an Appropriate Print Quality . . . . . . . . . . . . . . . . . . 5-11
Controlling a Plot’s Overall Appearance
5-1
Controlling a Plot’s Overall Appearance
Ways To Control the Plot’s Appearance
Ways to Control the Plots’ Appearance
Note. The “pens” discussed throughout this chapter are the “conceptual” pens in a
software palette, rather than the plotter’s physical print cartridges.
This chapter discusses the ways you can control the overall appearance of your
plots from the front panel in terms of:
pen width
pen shade
700
pen color
750C Plus
the treatment of overlapping lines
overall lightness/darkness
rendering color drawings in monochrome
overall print quality and resolution.
750C Plus
Some of these front-panel items take effect only on the next file you send from
your computer, that is, they do not affect any pages already in the plotter’s queue.
If this is the case, it is stated in the relevant part of this chapter.
Some of the controls are available using the front-panel menus (pen width,
overlapping lines and lightness). Print quality is controlled from the front-panel
keys. This chapter explains them in the sequence of the list at the top of this page.
For the HP DesignJet 750C Plus the pen color can be controlled using the
front-panel menus. Color/monochrome plot option is available using the
front-panel keys.
750C Plus
Why Change the Appearance of the Plot Using the Front Panel
Rather Than from Your Software?
By default, the plotter looks to your software to provide information on all the
above attributes. However, you may want to experiment with various effects, or
try a temporary change, without the need to change your drawing or your driver
settings.
5-2
Controlling a Plot’s Overall Appearance
Changing Pen Widths and Colors Using the Plotter’s Internal Palettes
Changing Pen Widths and Colors Using the Plotter’s
Internal Palettes
The plotter has three pen palettes. The factory palette cannot be changed. You
can, however, change the line width and color settings for each pen in the
remaining two palettes (called palette A and palette B). Initially, all three palettes
1
are identical. Each palette has 16 pens which can include pens of different widths
and for the:
HP DesignJet 700 any of the plotter’s 11 pen shades.
HP DesignJet 750C Plus, any combination of the plotter’s internal 256 colors
700
750C Plus
To See the Current Palette Settings
1 Make sure either a roll or a sheet of media is loaded.
2 Make sure that the front panel Color/Mono switch is set to Color.
750C Plus
3
Print the Current Configuration Plot, by pressing the ↑ and ↓ keys
simultaneously..
STATUS
↑
Press these two
simultaneously
Ready
↓
0014
Notice on the Current Configuration Plot that the 16 pens are numbered 0
through 15.
The 256 colors are numbered 0 through 255. These colors are specified in the
Palette Plot, as explained on page 5-4.
750C Plus
1
We are discussing “conceptual” pens here.
5-3
Controlling a Plot’s Overall Appearance
Changing Pen Widths and Colors Using the Plotter’s Internal Palettes
To See the Colors Available for a Palette
750C Plus
1 Make sure that the front-panel Color/Mono switch is set to Color.
2 To print the Palette Demo, go to the Demos menu and choose Palette.
Demos
In the Palette Demo, you will see 256 squares, numbered 0 through 255,
each showing one of the 256 colors available for selection in the plotter’s
internal palettes. The example below is color 6 (magenta), which happens to
be assigned to pen 6 in the factory’s default palette.
Palette
All menu modes
6
Pen number in factory default palette, and initially
therefore in all three palettes. 0 through 15.
6
255,0,255
Color number. 0 through 255.
RGB composition, scaled to 255 = 100%. In this example, it is
100% red + 0% green + 100% blue, which is magenta.
Notice that RGB and CMYK, – plus white – are assigned by default to pens 0
through 7, and that eight grayscales are included in the 256 colors.
The 256 colors shown in the Palette Demo are not the only colors you can print
with your plotter! Using your software, you can create many more colors and, as
long as you are using the correct driver, the plotter will reproduce these colors by
an appropriate mix of inks from its CMYK cartridges. The Palette Demo merely
shows the 256 colors available for use in the plotter’s internal palettes, should you
choose to use them.
5-4
Controlling a Plot’s Overall Appearance
Changing Pen Widths and Colors Using the Plotter’s Internal Palettes
To Change the Palette Settings
There are three palettes: Factory, Palette A and Palette B. You cannot change the
Factory palette, but you can define Palettes A and B to be whatever you choose.
Pen settings
Define palette
Item
Available Options
Factory, A, B.
Palettes
Pens
Full menu mode
Defaults:
Palette: Factory
Width: 0.35 mm
Color: (see
Palette Plot)
0 through 15.
Widths (mm)
0.13, 0.18, 0.25, 0.35, 0.50, 0.65, 0.70, 0.80, 0.90, 1.00,
1.40, 2.00, 3.00, 5.00, 8.00, 12.00.
Note that 0.13 mm is a one-pixel line width and renders
some colors as a dot pattern.
Shades
Colors
0%, 10%, 20%, 30%, 40%, 50%, 60%, 70%, 80%, 90%, 100%
700
0 through 255.
As specified on the Palette Plot.
750C Plus
The steps below explain how to define Palette A.
1 In the front-panel display, go to the Define Palette routine and choose Palette A.
2 Scroll to the pen number you want to change and press Enter.
3 The current width assigned to this pen is displayed, for example Width=0.35mm. If
you want to change it, press Enter, scroll to the width you want and then press
Enter again.
If you wish to change the color for the pen scroll to Color.
4 The current color assigned to the pen is displayed, for example Color=110. If you
want to change it, press Enter, scroll to the color you want and then press Enter
again.
750C Plus
5 When both width and color are correct, press Previous.
6 Scroll to the next pen number you want to change, press Enter and do steps 3
through 5 again.
7 When all pen definitions are correct, press Previous until you have exited the
menus.
IMPORTANT. The palette you have just defined will take effect only when you
select it to be the current palette, as explained next.
5-5
Controlling a Plot’s Overall Appearance
Changing Pen Widths and Colors Using the Plotter’s Internal Palettes
To Change the Selection of the Current Palette
Palette
Comments
Pen settings
Palette
Software
The plotter looks to your software for pen settings and
ignores all three internal palettes.
Palette A
Palette B
Factory
The plotter assigns the attributes defined in Palette A to the
pens defined in your software as 0 through 15.
All menu modes
Default: Software
The plotter assigns the attributes defined in Palette B to the
pens defined in your software as 0 through 15.
The plotter assigns the attributes defined in the Factory
Palette to the pens defined in your software as 0 through 15.
5-6
Controlling a Plot’s Overall Appearance
Changing the Treatment of Overlapping Lines (Merge Feature)
Changing the Treatment of Overlapping Lines
(Merge Feature)
There are two alternative settings for controlling overlapping lines. The feature is
called Merge.
You can set this feature from your software in some applications, for example in
AutoCAD.
Pen settings
Merge
Merge off.
Merge on.
Overlapping lines and area
fills are merged.
Full menu mode
Default: Off
A subsequent line hides a
previous line where they
overlap.
700
Merge off.
Merge on.
Overlapping lines and area
fills are merged.
A subsequent line hides a
previous line where they
overlap.
750C Plus
5-7
Controlling a Plot’s Overall Appearance
Changing the Overall Lightness/Darkness of a Plot
Changing the Overall Lightness/Darkness of a Plot
You can change the overall lightness/darkness of a plot by adjusting the amount of
ink used in your plots.
The feature is called Lightness and affects both grayscales and colors.
Device setup
Lightness
Dark
Normal
Light
Full menu mode
Default: Normal
The effect is exaggerated in these drawings.
As this is a simple way to change the appearance of your plot, you can achieve
better results if you use your software for different effects. However, some
examples of situations where you may find the feature useful are:
Where a tracing paper produces better print quality when the plotter uses a
smaller volume of ink.
Where a small variation in the amount of ink used produces a significant change
in the apparent darkness or color saturation of an image.
Where you want to reduce the drying time required: for example, for glossy
media in extremely humid conditions. (If you need to make a global change to
drying times for extreme environmental conditions, refer to page 3-23.)
5-8
Controlling a Plot’s Overall Appearance
Printing Color Drawings in Monochrome
Printing Color Drawings in Monochrome
A
A
Examples of why you may want to print a color drawing in monochrome are:
Because you want a draft where color is not important, for example to check
that the plot is not going to be clipped.
Because you want a version for photocopying in black and white.
750C Plus
Three important points:
The monochrome plot will render colors as grayscales rather than all as black.
If you want all colors to be printed as black, then you should set all your colors
to black in your software. This is most easily achieved in CAD software by
using a pen number that is 100% black. Alternatively, you could make one of
the plotter’s internal palettes (A or B) all black, and then select this as the
current palette (see earlier in this chapter for an explanation of palettes).
With monochrome plotting, you have the option to choose between true 300 and
true 600 dpi resolution (see page 5-11). This option does not apply to glossy
media types, on which the resolution is always true 300 dpi.
You cannot change the color/monochrome setting for plots already in the
plotter’s queue.
5-9
Controlling a Plot’s Overall Appearance
Printing Color Drawings in Monochrome
To Switch between Color and Monochrome
Affects next plot sent
1
Use the front-panel key shown below to toggle between color and
monochrome.
Color
Mono
750C Plus
If you are using one of the software drivers supplied with the plotter, you
can also make this setting (or an equivalent) within the driver. In this case,
the driver setting will override the front-panel setting. The front-panel
setting will, however, remain available as the default value, and the
front-panel light displayed will not change.
If you use the supplied AutoCAD driver, you can force a color plot to
monochrome by additionally setting the current palette to something other
than Software (see page 5-6).
0027
2 Send the plot from your computer.
The setting also impacts the plotter’s internal sample plots.
5-10
Controlling a Plot’s Overall Appearance
Choosing an Appropriate Print Quality
Affects next plot sent
Choosing an Appropriate Print Quality
You can set the overall print quality from the front panel. The main effects of your
print quality setting are shown in the table below.
Print Quality
Fast
Normal
Best
Setting
Speed
Ink Used
General tips
By choosing Fast, you will get draft-quality output in the shortest time. By
choosing Normal, and a suitable media type, you will get high-quality output in a
reasonable time. By choosing Best, you will get the highest possible quality for
the media type, but the printing time will be longer.
However, your plotter’s output speed, quality and particularly its resolution, also
varies according to:
Whether Sharp lines is set to Auto, On or Off (see page 5-14) on the front panel
or in your software.
750C Plus
The specification option when you loaded the media (see page 3-3).
5-11
Controlling a Plot’s Overall Appearance
Choosing an Appropriate Print Quality
The resolution at which your plot will be printed is summarized in the table below.
Resolution in dpi
Print Quality
DesignJet 750C Plus
DesignJet 700
Monochrome
300 x 300
Setting
Monochrome
Color
Fast
Normal
Best
300 x 300
600 x 600
600 x 600
300 x 300
300 x 300
600 x 600
1
1
1
600 x 600
2
1
600 x 600
1
Or 300 x 300, depending on your driver resolution setting or the software
application you have used.
2
Addressable dpi with Sharp lines set to Auto or On, using opaque bond, coated
paper and matte film only. This resolution depends on the type of image created
in your software application.
Recommended combinations of print quality and media type are given in the table
on page 3-6.
To get the very best print quality for images and drawings from graphics packages
(other than CAD drawings or other line drawings):
When loading the paper, specify “Heavy coated paper” on the front panel, rather
than “Coated paper”.
Set Print Quality to “Best”.
5-12
Controlling a Plot’s Overall Appearance
Choosing an Appropriate Print Quality
To Change the Print Quality
Affects next plot sent.
Software setting
takes priority.
1
Use the front-panel Print Quality key to toggle between the three print quality
settings.
Best
Normal
Fast
Print Quality
STATUS
Ready to plot
If you are using one of the software drivers supplied with the plotter, you can
also make this setting (or an equivalent) within the driver. In this case, the
driver setting will override the front-panel setting. The front-panel setting will,
however, remain available as the default value, and the front-panel light
displayed will not change.
0027
2 Send the plot from your computer.
The setting also impacts the plotter’s internal sample plots.
You cannot change the print quality setting for plots already in the plotter’s queue.
5-13
Controlling a Plot’s Overall Appearance
Choosing an Appropriate Print Quality
Improving Line Quality and Graphics Detail
Device setup
Sharp lines
The Sharp lines option refines the print quality of line drawings by smoothing the
fine gradations along the angles and curves of the printed image. This
enhancement produces:
Full menu mode
Default: Auto
Crisper lines.
Finer detail.
Line drawings with a ‘sharp’ appearance.
Only plots that have color content are affected by the Sharp lines option to produce
addressable 600 dpi resolution. Monochrome images are not affected by the Sharp
lines option as these are produced in true 300 or 600 dpi resolution, depending on
the print quality that you have selected.
750C Plus
The Sharp lines option has has three settings, Auto, Off and On, and can be set
either through the front-panel menu or HP supported Windows drivers. The
factory default setting is Auto.
With Sharp lines set to Auto you will always get best quality color plots, except
when you send the following files:
Mixed lines and scanned color images.
Mixed lines and color photographs.
CorelDRAW! (with color images).
For these files it is recommended that the Sharp lines default setting is changed,
depending on your preference for image or line quality:
Select On if you have a file which contains line and color images and you want
the lines to be plotted in Best quality, even if there is possible degradation to the
quality of the color image.
Select Off if you have a file which contains line and color images and you want
to optimize the quality of the color images.
Select Off if the plot is a complex vector file, such as a CorelDRAW! The plot
quality will be optimized for these circumstances.
Select Off if the output speed of the plotter is more important than Best quality.
5-14
Controlling a Plot’s Overall Appearance
Choosing an Appropriate Print Quality
For further information on Sharp lines see Troubleshooting, page 9-15.
750C Plus
With the Sharp lines set to Auto or On in the front-panel menu, the plotter
may not always produce an addressable 600 dpi plot. This may be because:
You have not selected Best on the front-panel Print Quality key, refer to
page 5-13.
You are using media other than Coated paper, Opaque bond or Matte
film.
Your application-software driver is overriding the front–panel selection.
You are plotting a color raster image or a line drawing combined with a
color raster image.
5-15
5-16
6
Managing Plots Being Printed or Drying . . . . . . . . . . . . . . . . . . 6-2
Managing Plots Not Yet Printed (The Queue) . . . . . . . . . . . . . . 6-4
To Replot an Image Using the Plotter’s Memory . . . . . . . . . . . 6-9
Avoiding Media Waste by Nesting Pages (Roll Media Only) . 6-10
Managing Your Plots
6-1
Managing Your Plots
Managing Plots Currently Being Printed or Drying
Managing Plots Currently Being Printed or Drying
To Cancel a Plot
X
Press Cancel on the front panel.
Cancel
The plotter advances the media as though the plot were finished.
0027
If queueing is on and there are no more plots in the queue, the cancelled plot is
placed in the queue and you can replot it as explained on page 6-8. If, in addition
to cancelling the plot, you want to delete it from the queue, see page 6-7.
To Cut a Plot Before Drying Is Complete (Roll Media Only)
Press Form Feed and Cut on the front panel.
Form Feed
and Cut
The plotter ignores the drying time and immediately drops the page into the
media bin.
0027
6-2
Managing Your Plots
Managing Plots Currently Being Printed or Drying
To Pause while Printing a Series of Plots
You can pause between two plots already sent from your computer, for example to
change the media type or replace the cartridges.
1
Press Pause on the front panel.
Pause
The plotter finishes the current plot and pauses (indicated by the Pause light
being on) until your press Pause again.
While the plotter is paused, you can use the front-panel as normal, for example
to change a front-panel menu setting or to load and specify a new media type.
0027
2 To resume printing, press Pause again.
6-3
Managing Your Plots
Managing Plots Not Yet Printed (The Queue)
Managing Plots Not Yet Printed (The Queue)
The normal sequence of events is:
1 You send a plot from your computer (or choose one of the internal sample plots
from the Demos menu).
2 The plotter’s Receiving light flashes while it receives and processes the data.
3 The plotter starts printing or, if queueing is on, places it in the queue until its turn
comes round.
To Start Printing a Plot That is Waiting for a Timeout
If all is in order (media loaded, cartridges loaded, no file error), there are still two
reasons why a plot you have sent from your computer may not start printing when
expected:
The plot file may lack a proper file terminator and the plotter is therefore
waiting for the specified I/O timeout period before assuming it is complete. See
page 7-9.
Nesting may be on and the plotter is waiting for the specified Nest wait timeout
period before calculating the appropriate nests. See page 6-12.
In either case, if you want to override the timeout period and start printing
Press Form Feed and Cut on the front panel.
Form Feed
and Cut
0027
6-4
Managing Your Plots
Managing Plots Not Yet Printed (The Queue)
What is the Queue?
Your plotter can store plots in a queue at the same time as plotting the current file.
It stores them by page, though if you send only single-page files, you can regard
these as plots. The size of the queue is limited by the number of pages (maximum
32) and the total memory occupied by the queue;
700
maximum standard memory 7 MB through 71 MB
maximum standard memory 11 MB through 75 MB
750C Plus
depending on which memory expansion modules you have installed. Remember
that file size and memory usage are not the same thing, as explained on page 7-10.
However, it is clear that the larger your files are, the fewer you can store in the
queue.
With queueing turned ON
Queueing & Nesting
Queue
You can send one or more plots to the plotter without waiting for the current
page to finish.
You can manipulate the pages in the queue, for example prioritizing them and
replotting them.
Full menu mode
Default: On
You can use nesting, the plotter’s media-saving feature (see page 6-10).
With queueing turned OFF
The plotter will not accept a file sent from the computer until the current page
has finished plotting and the plotter is ready.
You cannot use nesting (see page 6-10).
If you turn queueing off while pages are still in the queue, they will be plotted and
– if nesting is on – nested, until the queue is empty.
6-5
Managing Your Plots
Managing Plots Not Yet Printed (The Queue)
To Identify a Page in the Queue
Queueing & Nesting
Queue mgmt
In Queueing & Nesting, you can scroll through the pages in the queue.
Each has an identifier, comprising:
Page ID
All menu modes
<position in queue> : <plot name>
Position in queue
The page currently being plotted is in position 0. The next page to be plotted is in
position 1, the one after in position 2, etc. The previous page plotted is
position –1, the one before that in position –2, etc.
3
pages yet to be plotted
2
1
up to
32 pages
current page
0
–1
–2
pages already plotted
–3
Plot name
Some applications let you give your plot a descriptive name which it then conveys
to the plotter – for example “Building 2 Exterior”. If your software supports this
feature, this plot name is applied to each page and displayed after its queue
position:
1:Building 2 Exterior
Position in queue
If your software does not support this feature, your plotter will assign names to the
pages in its queue. The plotter-assigned name indicates how many thousands of
vectors make up the page:
1:92K Vectors
Position in queue
Note that this is not an indication of the amount of memory the page requires. For
that, see page 6-7.
6-6
Managing Your Plots
Managing Plots Not Yet Printed (The Queue)
To See the Size of a Page in the Queue
Statistic
Width
Comments
Page ID
The shorter side of the page, in millimeters.
The longer side of the page, in millimeters.
Statistics
Length
All menu modes
To Prioritize a Page in the Queue
To make any page in the queue the next one to be plotted, select it and choose
Page ID
Move to top.
Move to top
If nesting is turned on (see page 6-10), the prioritized page may still be nested with
others. If you really want this page to be printed next and on its own on the roll,
then first turn nesting off and then use Move to top to move it to the top of the
queue.
All menu modes
To Delete a Page from the Queue
Under normal circumstances, there is no need to delete a page from the queue after
plotting it, as it will just “fall off the end” of the queue as more files are sent.
However, if you have sent a file in error and want to avoid any chance of it being
replotted, you can simply delete it, by selecting it and choosing Delete page.
Page ID
Delete page
All menu modes
To remove a page that has not yet been plotted, simply identify it by it’s position in
the queue (see page 6-6) and delete it, by choosing Delete page.
If the page is currently being plotted (its queue position is 0), and you want both to
cancel the page and to delete it, first press Cancel and then delete it from the
queue.
6-7
Managing Your Plots
Managing Plots Not Yet Printed (The Queue)
To Make Copies of a Page in the Queue
Has The Page Do You Want
Already Been
Printed?
One Copy Or
Several?
What To Do
Yes
No
One
Use Move to top (see page 6-7).
Several
Use Copies (see below) and then use Move
to top (see page 6-7).
One
Use Copies (see below).
Several
In all cases, the page must be still in the queue.
Having selected the page and chosen Copies, use the scrolling keys to specify the
number of copies required, and press Enter. The number you enter is the actual
number of pages to be printed; for example, choosing 2 for a page not yet plotted
means you will get the one original and one copy. The maximum is 99.
Page ID
Copies
All menu modes
Default: 1
The setting you specify in this option overrides any value set by your software.
Note that, if Rotate (see page 4-7) was on when you sent the plot, every copy will
be rotated too.
6-8
Managing Your Plots
Replot an Image Using the Plotters Memory
Replot an Image Using the Plotter’s Memory
A
A
If you have sent an image from your computer, the plotter will retain this image in
its memory until another image is sent from your computer. The current image can
be plotted again using Replot on the front panel.
1
Press Replot on the front panel.
700
The Replot light flashes briefly while the plotter prints the current
image again.
Replot does not work if:
• another file has already been sent to the plotter (including internal
sample plots, for example the Setup Sheet)
• you have switched the plotter off and on again since first sending
the plot
• some files that contain Raster data may not replot because the entire
file may not still be held in the plotters memory.
6-9
Managing Your Plots
Avoiding Media Waste by Nesting Pages (Roll Media Only)
Avoiding Media Waste by Nesting Pages
(Roll Media Only)
What is Nesting?
Nesting means placing pages side-by-side on the media (rather than one after the
other), to avoid wasting media.
direction of
roll
paper flow
media saved
nesting off
nesting on
0028
The plotter may automatically rotate a page in nesting (see page 6-11). It may do
this even with a single page.
direction of
paper flow
nesting off
media saved
nesting on
0029
6-10
Managing Your Plots
Avoiding Media Waste by Nesting Pages (Roll Media Only)
When Does the Plotter Try to Nest Pages?
When all the following are true:
The plotter is loaded with roll media rather than sheet media.
In the front-panel menus, Queue is ON (the default). See page 6-5.
In the front-panel menus, Nest is ON (that is, set to either Optimal or In order).
See page 6-12.
Which Pages Qualify for Nesting?
In order to be in the same nest, the individual pages must be compatible on both
the following criteria:
Color or monochrome
Either all are color or all are monochrome. Remember that monochrome may
include a color plot rendered in grayscales by use of the front-panel Color/Mono
key – see page 5-9.
750C Plus
Print resolution
Either all are 300 dpi or all are 600 dpi – see page 5-11.
Which Pages May be Rotated?
Apart from obvious physical limitations on the roll, any page containing raster data
will not be rotated.
If you are using the Microsoft Windows driver supplied with this plotter, your files
do contain raster data and therefore the pages will not be rotated in nesting. The
normal line drawings of most CAD software do not contain raster data, and
therefore may be rotated in nesting.
6-11
Managing Your Plots
Avoiding Media Waste by Nesting Pages (Roll Media Only)
To Turn Nesting On or Off and Choose the Nesting Method
Nest Setting
Selected
Plotter’s Response
Queueing & Nesting
Nest
Off
The plotter will not nest pages.
Optimal
Choose this if you want to use the least amount of media.
All menu modes
Default: Off
The plotter will search all through the queue for suitable pages.
It will nest the pages according to an algorithm that, for most
combinations of page sizes, saves the most media. The
resulting nesting pattern may still vary, depending on the size of
the first page.
In order
Choose this if the speed with which you receive your plots is
most important.
The plotter will try to nest pages in their queue sequence. If it
comes across an incompatible page, it will stop searching and
print any nest it has already created.
What Happens to Nesting if you Turn Queueing Off?
Turning queueing off does not turn nesting off for pages already in the queue. The
plotter prints all the pages in the queue before accepting any more files. As soon as
you turn queueing off, the nesting setting also changes to off. When queueing is
turned on again, the plotter restores nesting to its previous setting.
How Long Does the Plotter Wait for Another File?
So that the plotter can make the best nest possible, it waits after a file has been
received to check if a subsequent page will nest with it or with pages already in the
queue. This waiting period is the nest wait time. The factory default nest wait time
is two minutes. This means that the plotter waits for up to two minutes after the last
file is received before plotting the final nest. You can change this waiting time
using the front panel menu (as shown opposite). The available range is 1 minute
through to 99 minutes.
Queueing & Nesting
Nest
Optimal
In order
Nest wait
All menu modes
Default: 2 minutes
6-12
Managing Your Plots
Avoiding Media Waste by Nesting Pages (Roll Media Only)
Getting the Best from Nesting (Nesting and Margins)
In order to “squeeze in” one more page, the plotter may reduce the right margin of
the right-most page by up to 3 mm (0.08 in). This is done only if:
What the plotter
may do
your Page format / Size is set either to a Best option or to a discrete standard
size, and if
the roll of media loaded is slightly narrower than a standard size.
You can reduce the side margins too, for every page, as explained on page 4-6. In
order to give the plotter the best chance of nesting the most pages, we recommend
that you set Page format / Margins to Smaller.
What you can do
Nesting and the Rotate Feature
Since nesting may automatically rotate pages, the front panel’s Page format /
Rotate setting is ignored as long as nesting is on.
6-13
6-14
7
To See the Current Overall Configuration of the Plotter . . . . . . 7-2
To See the Current Configuration of the Front-Panel Settings . 7-3
To Change the Front-Panel Settings . . . . . . . . . . . . . . . . . . . . . . 7-4
Recalibrating the Plotter for Accuracy . . . . . . . . . . . . . . . . . . . . 7-5
Changing the Graphics Language Setting for a Different
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
Changing the Serial Interface Settings . . . . . . . . . . . . . . . . . . . . 7-9
Changing the I/O Timeout Setting . . . . . . . . . . . . . . . . . . . . . . . 7-9
To Upgrade Your Plotter with More Memory . . . . . . . . . . . . . 7-10
To Upgrade Your Plotter with the Postscript Option . . . . . . . . 7-11
To Upgrade Your Plotter with a Network Interface . . . . . . . . . 7-12
Reconfiguring Your Plotter
Reconfiguration, Recalibration and Upgrades
7-1
Reconfiguring Your Plotter
To See the Current Overall Configuration of the Plotter
To See the Current Overall Configuration of the Plotter
Item
Comments
Utilities
Max X
Max Y
These two figures, in millimeters, give the size of the current
plotting area, that is, the area in which the plotter will print the
next plot unless it is changed. Normally each plot file received
sets these dimensions with its Page Size command. You can
impact it by:
Statistics
Full menu mode only
the current front-panel setting for Page format / Size.
the media size currently loaded.
Remember:
Plotting area = page size minus margins.
X represents the vertical (paper path) axis.
Y represents the horizontal (carriage path) axis.
This is the revision number of the plotter’s internal code.
Code rev
RAM present
This is the size, in megabytes, of the plotter’s main standard
memory, plus the amount of memory reserved for printing.
This does not correspond directly to the size of your files on
the computer, as explained on page 7-10.
This is the total RAM, not the RAM currently free.
Media
This is the media type which the plotter thinks is currently
loaded (or was last loaded), on the basis of what you specified
when you loaded it. For an explanation of media types, see
page 3-3.
In this display, the following abbreviations are used:
Translucent = Translucent bond.
High-gl photo = High-gloss photo paper.
Semi-gl photo = Semi-gloss photo paper.
750C Plus
High-gl film
Nat. tracing
= High-gloss film.
= Natural tracing paper.
ROM SIMM
This tells you if an optional ROM SIMM is installed in the
plotter, for example PostScript.
7-2
Reconfiguring Your Plotter
To See the Current Configuration of the Front-Panel Settings
To See the Current Configuration of the Front-Panel
Settings
1 Make sure either a roll or a sheet of media is loaded.
2
Print the Current Configuration Plot, by pressing the up-arrow and down-arrow
keys simultaneously.
STATUS
↑
Press these two
simultaneously
Ready
↓
0014
The Current Configuration Plot lists, in an easy-to-read format, all the items
available in the front-panel menus, together with their current settings (in red
italics, for the HP DesignJet 750C Plus). Note that some of the items do not
appear in the front-panel display unless you have set Utilities / Menu mode to Full
(the default is Short, so that they do not appear). See the legend at the bottom of
the plot for details.
NOTE. Do not confuse the Current Configuration Plot with the Service
Configuration Plot, which you can print by selecting Utilities / Service config.
Apart from its use in calibrating the plotter, as explained on page 7-5, the Service
Configuration Plot is likely to be needed only by a service engineer.
7-3
Reconfiguring Your Plotter
To Change the Front-Panel Settings
To Change the Front-Panel Settings
Chapter 2 of this manual explains how to use the front-panel display, including
how to change any of the settings. It also explains the small menu graphics that
appear in the left margins of this manual whenever a particular menu item is
explained.
These graphics
are explained in
chapter 2.
The meanings of all the items in the front-panel menus are explained at the
relevant point in this manual. Refer to the index at the back of the manual for the
item you want to change.
7-4
Reconfiguring Your Plotter
Recalibrating the Plotter for Accuracy
Recalibrating the Plotter for Accuracy
When to Recalibrate the Plotter
Your plotter was calibrated at the factory using HP Matte Film, with a thickness of
0.12 mm (0.0048 in);
at 23 C (73 F),
with 50-60% relative humidity.
It will operate with greatest accuracy in similar environmental conditions. If you
are operating under significantly different conditions, you should recalibrate the
plotter as explained here. The plotter’s environmental specifications are given on
page 11-4. Also, if you are using a non-standard media type, you should first
recalibrate the plotter for that media type. For supported media types, see
page 3-3. You may also need to recalibrate the plotter if you have banding
problems, see page 9-20.
A Quick Guide to Whether Recalibration is Necessary
1 Make sure E/A0-size or D/A1-size media is loaded.
Utilities
2 Print the Service Configuration plot, by choosing the option shown in the menu
Service config
graphic on the left.
Full menu mode
3
Near the top of this plot are a pair of Xs. With a ruler measure the distance
between them. It should be 500 mm. If significantly different you will need to
recalibrate the plotter as described on the following page
X
500mm
X
7-5
Reconfiguring Your Plotter
Recalibrating the Plotter for Accuracy
To Recalibrate the Plotter
1 Choose your media type (sheet or roll). If recalibrating for a non-standard media
Utilities
type, use that type. Otherwise, HP Matte Film will give greatest accuracy.
Accuracy
2 Choose your media size. Sheet media must be either E/A0 or D/A1.
3 Go to Recalibrate in the front-panel menus, as shown above left.
Recalibrate
4 Choose Create pattern. The message Calibrating is displayed. If sheet media is
Full menu mode
only
loaded, this will be ejected. If roll media is loaded, you are asked to remove it.
5 When prompted, load your media, using the normal procedure. If using sheet
media, load it in portrait orientation, unless you chose D/A1-size media for an
E/A0-size plotter, in which case load it in landscape orientation.
6 When the calibration plot is finished, remove it.
7 Unload any unplotted media.
8
Rotate the calibration plot 90 counterclockwise and reload it printed side
down, so that the black arrows go into the plotter first. NOTE: Even if you
selected roll media in step 5, this time you must select sheet media.
1
2
3
0030
9 Go to Recalibrate again and, this time, choose Measure pattern.
10 When the plotter has finished measuring and has ejected the sheet, STATUS/Ready
is displayed. The recalibration routine is finished.
To Restore the Factory’s Calibration
From the Accuracy menu, choose Restore factory. That’s all.
Utilities
Accuracy
Restore factory
Full menu mode only
7-6
Reconfiguring Your Plotter
Changing the Graphics Language Setting for a Different Application
Changing the Graphics Language Setting for a
Different Application
Your software application communicates with the plotter by a graphics language.
The plotter supports HP industry standard CAD language
HP-GL/2 (7856)
HP-GL (7586B)
HP RTL
The plotter’s default setting is designed to work successfully with most
applications, and is called 7586, HP-GL/2. However, it’s possible that with some
older or less common applications, you may need to change this setting to
HP-GL/2, as explained in the table below.
To Change the Graphics Language Setting
Graphics
Language
Comments
Device setup
Lang
7586, HP-GL/2 This should work successfully for most software applications.
With this graphics language setting another parameter is
available: Terminator. Try changing this setting from Normal
(the default) to Special:
Full menu mode
Default: 7586,
HP-GL/2
if you are using an obsolete HP 7586 (pen plotter) driver,
and your plots are incomplete.
HP-GL/2
Try this setting:
if you have experienced plot position problems.
if you have experienced timing problems.
However, if you choose this setting, you don’t have access to
the Terminator option.
7-7
Reconfiguring Your Plotter
Changing the Graphics Language Setting for a Different Application
Graphics Language and Networks
Note for system administrator. If you are using the plotter with a network
spooler, consider modifying the spooler to automatically insert the PJL
language-switching commands at the beginning and end of each file. This allows
the plotter to switch automatically into the correct graphics language for your
current plot and returns the plotter to the front panel graphics language setting for
subsequent plots. For PJL reference information, see page 11-13.
7-8
Reconfiguring Your Plotter
Changing the Interface Settings and I/O Timeout Setting
Changing the Interface Settings
Network
With a network interface (such as HP JetDirect Print Server), refer to your network
interface documentation for advice on any front-panel configuration.
Parallel
Serial
With a parallel interface, no front-panel configuration is necessary.
With a serial interface, you should have configured it when installing the plotter, as
explained on page 1-29. However, you may need to reconfigure it:
When you connect a new computer to the plotter.
When you output to the plotter from a new application.
If you experience problems with distorted or unintelligible plots.
To Change the Serial Interface Settings
I/O Setup
This task is explained in detail on page 1-29, including a note of the defaults and
likely requirements.
RS-232-C
Full menu mode
To Change the I/O Timeout Setting
Some software may not write a proper file terminator at the end of the file. In this
case, the plotter will not know that the file is complete and will wait for more data
until the end of the “I/O Timeout” period. By default, this period is 30 minutes,
but you can change it in the menu (indicated on the left) to as little as 30 seconds.
I/O Setup
I/O Timeout
Full menu mode
7-9
Reconfiguring Your Plotter
To Upgrade Your Plotter with More Memory
To Upgrade Your Plotter with More Memory
Your plotter comes with 7 MB of standard memory (4 MB of main memory and 3
MB of printing memory). You can expand this up to a maximum of 71 MB of
standard memory by adding one or two memory expansion modules.
700
Your plotter comes with 11 MB of standard memory (8 MB of main memory and 3
MB of printing memory). You can expand this up to a maximum of 75 MB of
standard memory by adding one or two memory expansion modules.
750C Plus
For HP part numbers, see page 11-14.
For installation details, see the task starting on page 1-6.
File Size and Memory Usage
There is no direct relationship between file size on your computer and memory
used in the plotter to print that file. In fact, because of file compression (and
general complexity) it is often impossible to estimate how much memory will be
used. In general, thicker lines ( 0.5 mm), complex objects (such as polylines)
and fills will all use significantly more memory.
This also means that size of the largest file you can store in the plotter’s queue is
not the same thing as the amount of memory installed in your plotter.
7-10
Reconfiguring Your Plotter
To Upgrade Your Plotter with the Postscript Option
To Upgrade Your Plotter with the Postscript Option
To use your plotter with Macintosh applications that output files in the Adobe
PostScript language, you need to order the PostScript Upgrade Kit. For the HP
part number, see page 11-14. Such applications include, for example:
Adobe Illustrator
Adobe Photoshop
Aldus Freehand
Aldus PageMaker
QuarkXpress.
Many Microsoft Windows applications (for example CorelDRAW!), can also
output PostScript files, but in most cases all you need is the Microsoft Windows
driver supplied with your plotter.
As well as a PostScript driver for your software, the PostScript Upgrade Kit
includes a ROM SIMM, which you install in the back of your plotter.
The upgrade kit comes with its own detailed installation instructions. When
removing the cover plate, as instructed, use a flat-head screwdriver and
remove only the four screws on the cover plate.
Note that you must install the PostScript ROM SIMM in the second slot from
the left.
Slot for PostScript Option
(Back of Plotter)
1 2 3 4
7-11
Reconfiguring Your Plotter
To Upgrade Your Plotter with a Network Interface
To Upgrade Your Plotter with a Network Interface
You can connect your plotter directly to a LAN using an optional network interface
card such as the HP JetDirect Print Server. Depending on your needs, you may
want to use the network interface instead of or in addition to the parallel and serial
interfaces.
The slot for a network interface card is situated at the back of the plotter,
alongside the parallel and serial ports. Using a flat-head screwdriver,
unscrew only the two screws on the cover plate.
Slot for network interface card
For installation and configuration of the HP JetDirect Print Server, see the
documentation supplied with that product.
1845d
HP JetDirect Print Server
For part numbers of the HP JetDirect Print Server, see page 11-15. This interface
supports most common network environments and the specification of this product
is updated regularly. For details of the latest version available, please contact your
HP dealer or HP Sales and Support office.
7-12
8
Replacing the Print Cartridge(s) . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Cleaning the Plotter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
“Normal” Plotter Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
Maintaining Your Plotter
Cleaning and Service
8-1
Maintaining Your Plotter
Replacing the Print Cartridge(s) and Cleaning the Plotter
Replacing the Print Cartridge(s)
Replaceable print cartridge(s) have been used in your plotter, greatly reducing its
user maintenance requirements, as these are the components that experience the
greatest wear and tear.
Under normal use, you will probably find that you have to replace the black
cartridge more often than the color cartridges.
750C Plus
For instructions on when and how to replace cartridge(s), see the section starting
on page 3-26.
Cleaning the Plotter
Cleaning is limited to the outside of the machine. Use a damp sponge or a soft
cloth and household cleaner.
To avoid an electric shock, make sure that the plotter is switched OFF and
unplugged before you clean it. Do not let water get inside the plotter.
W A R N I N G
C A U T I O N
Do not use abrasive cleaners on the plotter.
Any maintenance or repairs beyond this should be done by a qualified service
technician.
8-2
Maintaining Your Plotter
“Normal” Plotter Use
“Normal” Plotter Use
“Normal” plotter use means less than
20 pages per day (if medium-density E/A0 CAD plots), or
12 pages per day (if medium-density E/A0 image prints).
If your drawings are smaller than E/A0, the number of pages per day can be higher.
If you use the plotter less than this, it is unlikely you will need to get it serviced. If
you use the plotter more than this, it is possible that, after a period of time, it will
need to be serviced. The plotter itself keeps an internal count of total pages printed
and total passes of the cartridge carriage. If the front panel periodically displays
STATUS
Maintenance advised
this means that your use of the plotter has exceeded one of the following
warranty limits:
either 20,000 pages printed
or 4,500,000 passes of the cartridge carriage.
Contact your local HP dealer or HP service engineer to arrange a service. After
the service the message will disappear. If you choose not to have the service, you
may continue to use the plotter as normal, but may encounter a number of
operational or print-quality problems.
You can check your current count of pages printed and passes of cartridge carriage
by printing the Service Configuration Plot.
8-3
Maintaining Your Plotter
“Normal” Plotter Use
To Print the Service Configuration Plot
1 Make sure media is loaded.
Utilities
2 In the front-panel menus choose the option shown on the left.
Service config
Full menu mode
8-4
9
Using the Documentation to Help Solve Problems . . . . . . . . . . 9-2
Locating the Source of Problem . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Solving Media-Handling Problems . . . . . . . . . . . . . . . . . . . . . . 9-4
Solving Print Cartridge Problems . . . . . . . . . . . . . . . . . . . . . . . 9-7
Clearing a Media Jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Solving Communication Problems . . . . . . . . . . . . . . . . . . . . . . 9-9
Solving Problems with Plot Position or Content . . . . . . . . . . . 9-10
Solving Print Quality Problems . . . . . . . . . . . . . . . . . . . . . . . . 9-16
Solving Front-Panel Problems . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
Solving Miscellaneous Problems . . . . . . . . . . . . . . . . . . . . . . . 9-23
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
Troubleshooting
9-1
Troubleshooting
Using the Documentation to Help Solve Problems
Using the Documentation to Help Solve Problems
If you are looking for the meaning of an error message, see chapter 10.
If you know the problem is related to a certain task, first check the relevant
section in this manual, for the step-by-step procedures. Use this manual’s index
to find the section. For example, if you are having difficulty with your page
format, refer to chapter 4, titled: Controlling the Page Format.
If the problem persists, refer to the appropriate section in this chapter. The
sections are
– Solving media-handling problems
– Clearing a media jam
– Solving problems with plot position or content
– Solving print quality problems
– Solving miscellaneous problems.
If the problem could be related to your software driver, and you are using an
HP driver, refer to the drivers’ troubleshooting documentation and the
‘On-Line-Help’ in your application software.
If the problem has no obvious cause, read “Locating the source of the problem”
on the next page.
If you still cannot solve the problem, refer to “Getting help” on page 9-25.
9-2
Troubleshooting
Locating the Source of Problem
Locating the Source of the Problem
1 Look at the front-panel display for any error message. For an explanation, see
chapter 10.
2 Test the plotter.
Switch the plotter off. Ensure that the power cord is firmly inserted in the
plotter and plugged in to an outlet that you know works.
Switch the plotter on. Print a sample plot (see page 1-24). If the plotter plots
this correctly, the problem is probably not with the plotter.
3 Test your computer hardware and interface.
Ensure that you have the correct interface cable between the computer and the
plotter and that it is firmly connected to the correct ports (see the sections
starting on page 1-27).
Check that your plotter’s graphics language setting (in Device setup / Lang)
matches the requirements of your software.
Serial interface users only. Check that your plotter’s serial interface settings
(in I/O Setup / RS-232-C) match the requirements of your computer hardware
and application software. See page 1-29 for details. Also, if you have changed
your interface, switch the plotter off and then on again before trying to plot.
9-3
Troubleshooting
Solving Media-Handling Problems
Solving Media-Handling Problems
If the Front Panel Keeps Indicating that Media Is Misaligned or
Incorrectly Positioned.
Roll media:
Have you:
Loaded the roll the wrong way. The media should load over the roll toward
you.
Loaded the media at an angle. The right-hand edge must be parallel to the
perforated line on the plotter.
Sheet media
Have you:
Loaded the media at the wrong side of the entry slot. It must be loaded with the
right-hand edge against the perforated line on the plotter.
Loaded the media at an angle. The right-hand edge must be parallel to the
perforated line on the plotter.
Pushed or held the media back as it is loading. You must hold the media only
by the edges and immediately release it when the plotter is loading.
It is also possible that the media itself is crumpled or warped or has irregular
edges.
If you are using hand-cut media, perhaps the edges do not form a right-angle or
they are rough. It is not recommended to use media that you have cut yourself;
use only purchased sheet media.
If you cannot make your media’s leading edge straight, you can turn on the
skew tolerance feature (Device setup / Skew tolerance). See page 3-21, but
remember that this feature can skew your plot on the page.
9-4
Troubleshooting
Solving Media-Handling Problems
If Media Crumples When You Load it
Clear any obstructions in the media path.
Be sure the leading edge is straight and free of tears. Cut a straight edge with
the knife if necessary.
If your media is curled, and if both sides are the same, load it with the curved
(hollow) side towards you (Certain media types – for example coated paper –
have a plotting side and a non-plotting side and these must be loaded plotting
side down.)
When loading media, hold each edge and push the media into the plotter evenly
against the stops until a slight buckle develops evenly across the media. Let go
as soon as it starts to feed into the plotter.
If you have just moved the plotter or your media from an environment with a
different humidity level, let the media stabilize for at least 15 minutes before
loading it.
Roll media only. Open the roll cover and raise the lever. Unload the leading
edge of the roll. Push the media all the way to the right so that it is flush against
the media stop on the roll core. Then reload the media.
If Plots Do Not Feed Out Properly From the Plotter
Make sure the roll cover is completely closed before you plot.
If The Automatic Cutter Does Not Cut Immediately When a Plot
Has Finished
Check the Page format / Margins setting. When this is set to Smaller, the plotter
waits until the next plot begins plotting so it can create a 10 mm margin
between both plots or nesting sets.
Press the Form Feed and Cut key if you need to cut the media before the
ink-drying time has passed or before the next plot begins plotting. Use caution
to avoid smearing the ink.
Check the ink-drying time and change if necessary (Device setup / Drying time).
9-5
Troubleshooting
Solving Media-Handling Problems
If the Automatic Cutter Does Not Work
The automatic cutter is activated only when roll media is loaded.
Your software application may have disabled the automatic cutter. Refer to your
software documentation or contact your software vendor for more information.
If Plots Fall on the Floor After Being Cut
Do not let more than twenty plots accumulate in the bin.
Make sure you have loaded roll media properly. If loaded incorrectly, the
natural curl of the media may cause it to miss the bin and fall to the floor.
If a Sheet Is Ejected When You Switch On the Plotter
The plotter is undertaking an automatic calibration check. Simply wait for the
STATUS / Ready message and then reload the sheet.
If Plots Do Not Stack Properly in the Bin
You may be too close to the end of the roll. The natural curl near the end of the
roll can cause stacking problems. Load a new roll or remove plots manually as
they are completed.
If plotted media is sagging or wrinkling between the bin wires after it is cut and
fed out, try placing a sheet of scrap paper in the bin shelf that is at least the size
of the plot.
If you are mixing plots or nesting sets of several different sizes, you are more
likely to have stacking problems because of the different sizes of media in the
bin.
9-6
Troubleshooting
Solving Print-Cartridge Problems
Solving Print-Cartridge Problems
!
If the Access Cartridge(s) Key Does Not Work
Make sure the window is closed before you press Access Cartridge(s).
If the Plotter Runs the Cartridge-Alignment Routine
Unexpectedly
The plotter runs the automatic cartridge alignment procedure every time you
load, replace or even reseat a cartridge, whether it is a new cartridge or not. Do
not remove the cartridge(s) unnecessarily.
You can stop the alignment by pressing Cancel, but the plotter will restart the
alignment procedure the next time you switch it on.
If Brand New Cartridge(s) Have Problems
Check the cartridge(s) to be sure you have removed the protective nozzle tape.
Try reseating the cartridge(s).
Don’t forget that, after you remove or reseat a cartridge, the plotter will run its
automatic cartridge alignment procedure – see page 3-27.
For troubleshooting other problems with the print cartridge(s), see the section
starting on page 9-16.
9-7
Troubleshooting
Clearing a Media Jam
Clearing a Media Jam
1
Switch OFF the plotter, open the window and raise the media lever.
OFF
1867
Don’t touch the stainless steel strip that runs the length of the plotter behind
the cartridge carriage; its edge is very sharp. Keep hair, jewelry, clothing,
and foreign objects away from the plotter mechanisms.
W A R N I N G
When moving the cartridge carriage, touch only the black plastic parts.
2 Carefully move the cartridge carriage out of the way – if possible all the way to the
enclosed area on the left or the right. Which way you are able to move it depends
on where the media is jammed. If the plotter was in the process of cutting media at
the time of the jam, the cutter carriage will be attached to the cartridge carriage and
will move with it.
3 Carefully remove any of the jammed media which you can easily lift up and out
from the top of the plotter.
4 Carefully pull the rest of the roll or sheet down and out of the media entry slot.
5 Lower the window and the lever and switch on the plotter. Press the Form Feed
and Cut key to eject any pieces of media that are still in the media path.
6 Reload the media as normal – see page 3-10. Remember that, if it’s a roll, you
may need to trim the edge.
9-8
Troubleshooting
Solving Communication Problems
Solving Communication Problems
?
If There is a Problem Communicating between Your Computer
and the Plotter
Some symptoms of a communication problem are:
– The front-panel Receiving light does not come on.
– The front-panel display does not show STATUS / Receiving.
– Your computer displays an error message when you are trying to print.
– Your computer or plotter “hangs” (stays idle) while communication is taking
place.
– Your plotted output shows random or inexplicable errors (misplaced lines,
partial drawings etc.).
Items to start checking are:
Have you selected the correct interface port in your software?
Does the plotter work correctly when receiving files from other software?
If the plotter is connected to a network, try using it when connected directly to
your computer.
If your plotter is connected to your computer via any other intermediate devices,
such as switch boxes, buffer boxes, cable adapters, cable converters etc., try
using it when connected directly to your computer.
Try another interface cable. For details of supported cables, see page 11-8.
9-9
Troubleshooting
Solving Problems with Plot Position or Content
Solving Problems with Plot Position or Content
If you don’t find the solution to the problem here, other sources of help are:
The documentation supplied with the driver that you are using to manage the
output from your software application to the plotter. For example, the online
and printed documentation included in the following two drivers supplied with
your plotter:
– HP plotter drivers for AutoCAD
– HP plotter driver for Microsoft Windows applications
The documentation supplied with your application software, for example the
AutoCAD Reference Manual.
If the Plot Is Completely Blank
Check the print cartridge(s) to be sure you have removed the protective nozzle
tape from all of them. Do not forget that, after you remove or reseat a cartridge,
the plotter will run its automatic cartridge alignment procedure – see page 3-27.
Cartridge(s) may be out of ink. For an explanation of how to check if a
cartridge is out of ink, see page 3-26.
9-10
Troubleshooting
Solving Problems with Plot Position or Content
If the Output Contains Only a Partial Plot
Did you press Form Feed and Cut before all the data was received by the
plotter? If so, you have ended the data transmission and will have to print the
plot again. (You normally don’t need to press Form Feed and Cut to unload
the plot.)
The I/O Setup / I/O Timeout setting may be too short. Increase the setting and
plot again. See page 7-9.
The file may be too big for the plotter’s memory. For information on memory
expansion modules, see page 11-14.
There may be a communications problem between your computer and the
plotter. Make sure interface cable is connected properly.
Check to make sure that your software settings are correct for your current plot
size (e.g., long-axis plots).
If you are using network software, make sure it has not timed out.
See also under “If the plot is clipped” on page 9-12.
9-11
Troubleshooting
Solving Problems with Plot Position or Content
If the Plot Is Clipped
This normally indicates a discrepancy between the actual plotting area on the
loaded media and the plotting area as understood by your software. For general
advice on plotting areas and page size, see chapter 4.
Check the actual plotting area for the media size you have loaded. Plotting area
= media size minus margins. For media size and margins, see page 11-2. For
actual plotting areas, see page 11-6.
Check what your software understands to be the plotting area (which it may call
“printable area” or “imageable area”). For example, AutoCAD assumes
standard plotting areas that are larger than those used in this plotter.
Check that the orientation of the media is the same as that assumed by your
software. The front–panel Page format / Rotate option changes the orientation
of a drawing and, on roll media, the orientation of the page. It is possible that a
rotated plot on roll media may be slightly clipped in order to retain the correct
page size, as explained on page 4-8.
You may have asked to rotate the plot from portrait to landscape on media that
is not wide enough, for example a D/A1-size plot rotated on a D/A1-size roll.
If necessary, change the plotting area in your software. For example, in
AutoCAD, specify User Sizes (see AutoCAD documentation).
The file may be too big for the plotter’s memory. This is the case if the front
panel displays “Out of memory – data was lost”. For information on memory
expansion modules, see page 11-14.
If a Long-Axis Plot Is Clipped
Does your software support long-axis plots?
Have you specified an appropriate media size in your software?
Make sure that the plotter’s Page format / Size is set to Inked area.
9-12
Troubleshooting
Solving Problems with Plot Position or Content
If the Entire Plot Is in One Quadrant of the Correct Plotting
Area
Is the page size configured in the software too small?
Are you sure that your software does not believe the drawing to be in one
quadrant of the page?
Otherwise, this indicates an incompatibility between the software and the plotter:
Is your software configured for this plotter? For general advice, see page 1-35.
For advice specific to your software, see either the documentation supplied with
the driver or any Software Application Notes supplied with your plotter.
If you still have not found the solution, try changing the plotter’s Graphics
Language setting on the front panel (Device setup / Lang).
If the Plot Is Unexpectedly Rotated
Check the front-panel Page format / Rotate setting. See page 4-7.
If Queueing and Nesting are both ON, plots may be automatically rotated to
save media. See page 6-11.
If the Plot Is a Mirror Image of Your Drawing
Check the front-panel Page format / Mirror setting.
If the Plot Is Inaccurate
If you notice problems with accuracy, print the Service Config plot, as
explained on page 7-5, to see if the plotter needs to be recalibrated.
9-13
Troubleshooting
Solving Problems with Plot Position or Content
If the Plot Is Distorted or Unintelligible
The interface cable between your computer and the plotter could be faulty. Try
another cable to see if the problem is corrected.
If you are using a serial interface between the plotter and your computer, make
sure the plotter’s serial interface settings match the settings and requirements of
your software and hardware. See page 1-29.
If One Plot Overlays Another Plot on the Same Sheet
The I/O Setup / I/O Timeout setting may be too long. Decrease the setting and
plot again. See page 7-9.
If Device setup / Lang is set to 7586,HP–GL/2 (the default), try changing the
Terminator setting and send the files again.
If Pen Settings Seem To Have No Effect
Either you have changed them in Pen settings / Define palette but forgotten to
select that palette in Pen settings / Palette,
!
or you expected the software-driven pen settings but the front panel Pen
settings / Palette is not set to Software.
See page 5-6.
If the Plotter Produces a Black and White Plot When You
Expected a Color Plot
Check the front panel Color/Mono setting, and the equivalent setting in your
software.
750C Plus
9-14
Troubleshooting
Solving Problems with Plot Position or Content
If the Plotter Has Printed a Different Plot Than the One You
Were Expecting
?!
One possibility is that you have accidentally initiated one of the plotter’s internal
plots:
The Cartridge Alignment Plot. (A small pattern of lines without text.) This is
printed automatically every time you replace, or reseat a cartridge.
The Current Configuration Plot. (A graphic and text plot with the current
configuration details) This is plotted by simultaneously pressing the two arrow
keys on the front-panel.
The Sample Plot. (A graphic plot with product information) This is plotted
from the front-panel menu Demos / Samples.
The Front-Panel Menu Plot. (A text plot showing the complete menu
structure) This is plotted from the front-panel menu Demos / Menu.
The Service Configuration Plot. (A text plot with service information) This is
plotted from the front-panel menu Utilities / Service Config.
The Palette Demo Plot. (A plot with 256 colored squares) This is plotted
from the front-panel menu Demos / Palette.
750C Plus
750C Plus
If the Quality Of A Color Plot Is Not as Good as You Were
Expecting
Select Best on the front-panel Print Quality key and plot again.
Did you specify the correct media type when loading? The highest line quality
is only produced using Opaque Bond, Coated Paper or Matte Film. For details
of media types, see page 3-3. To find out the plotters’ current media type
setting, see page 7-2.
Your application-software driver may be overriding the Sharp lines selection on
the front–panel menu.
Are you plotting something other than a line drawing, for example a
CorelDRAW! file? If so, you may want to experiment to improve the output
quality by setting Sharp lines to Off on the front-panel menu, and plot again.
Are you plotting a CAD drawing with small raster images? Try setting Sharp
lines to On, and plot again.
When loading the paper, specify “Heavy coated paper” on the front panel, rather
than “Coated paper”.
9-15
Troubleshooting
Solving Print-Quality Problems
Solving Print-Quality Problems
To achieve the best performance from your plotter, we recommend you only use
genuine HP accessories and supplies, whose reliability and performance have been
thoroughly tested to give trouble-free performance and best-quality plots. For
details of HP media, see page 3-3 and the Supplies Source catalog supplied with
the plotter.
If the Color Is Not as Expected
The means of accurately managing the colors printed by your plotter vary with the
software application and driver being used. Refer to the following documentation:
The Software Application Note for your application, in the specific package
shipped with this plotter.
750C Plus
Online documentation in the Microsoft Windows driver shipped with your
plotter, particularly in the Color Options dialog box.
Additionally, remember that your plotter may be configured to use one of its
internal pen palettes instead of your software’s palette (which is the default). See
the section starting on page 5-3.
If There Are White Streaks in Solid Fill Areas
This may mean that a cartridge nozzle is blocked. Unless you have switched
cartridge check off (see page 3-26), the plotter normally detects this problem and
tries to clear the nozzle automatically. However, some nozzles may still remain
blocked, and in this case, the plotter will display Service cartridge(s) on the front
panel. This means you should replace the problem cartridge, as explained from
page 3-26. If you are unsure which cartridge has the problem, refer to the next
page.
9-16
Troubleshooting
Solving Print-Quality Problems
If There are Other Gaps in Solid Areas or in Lines
1 One or more of your cartridges may be out of ink. For an explanation of how to
check, see page 3-26.
2 If the ink levels are OK, try to assess which cartridge has the problem. Look at
your plot; If the problem occurs only in one of the following colors – yellow, cyan,
magenta, red, green, blue or black – then you can eliminate one or more of the
cartridges. Remember that the plotter’s cartridges are yellow, cyan, magenta and
black, and that “pure” red, green and blue are made up as follows:
750C Plus
=
=
=
+
+
+
red
yellow
cyan
magenta
yellow
cyan
green
blue
magenta
3 If you know which cartridge has the problem, then try reseating it to ensure good
electrical connections. While it is out of the carriage, check the print nozzles to
make sure the protective tape has been removed. Don’t forget that, after you
remove or reseat a cartridge, the plotter will run its automatic cartridge alignment
procedure – see page 3-27.
4 If you don’t know which cartridge has the problem, then print the Service
Configuration Plot, by choosing Utilities / Service Config on the front panel. This
plot contains a pattern for each of the four cartridge colors (yellow, cyan, magenta
and black) which you can examine for gaps or streaks. If you can identify a
problem cartridge, try the checks described in 3 above.
5 If the problems persist, try running the recalibration routine. See page 7-5.
6 If the problems still persist, replace the cartridge(s). See page 3-26.
9-17
Troubleshooting
Solving Print-Quality Problems
If There are Jagged Vertical or Horizontal Lines
Did you specify the right media type when loading the media? For details of
front-panel media types, see page 3-3. To find out the plotter’s current type of
media setting, see page 7-2.
Force the automatic cartridge alignment procedure by reseating a print
cartridge.
If the problem persists, replace the print cartridge(s). See page 3-26.
If There are Slightly Warped Lines
The media itself may be warped. This can happen if it has been used or stored
in an extreme environment. For all environmental specifications, see page 11-4.
If There are Color “Shadows”
750C Plus
Force the automatic cartridge alignment procedure by reseating any one of the
print cartridges.
If One or More Cartridges are not Printing at All
Look to see if the cartridge is out of ink. See 3-26.
If it is still not printing, remove the faulty cartridge(s) and check the print
nozzles to make sure the protective tape has been removed. Do not forget that,
after you remove or reseat a cartridge, the plotter will run its automatic cartridge
alignment procedure – see page 3-27.
9-18
Troubleshooting
Solving Print-Quality Problems
If There are Blurred Lines (Ink “Bleeds” from Lines)
Perhaps you are not using HP media. For details of HP media, see page 3-3 and
the Supplies Source catalog supplied with the plotter.
The plotter may be operating in an area where the temperature and humidity are
too high. For environmental specifications, see page 11-4. To allow for
extremely dry or humid environments within the specification, see page 3-22.
Did you adjust the drying time in the front-panel menu purely to speed up the
plotters output? For details of drying time adjustments see page 3-23.
If There are Blotchy Areas (Uneven Fill Density)
Perhaps you are not using HP media. For details of HP media, see page 3-3 and
the Supplies Source catalog supplied with the plotter.
Did you specify the right media type when loading the media? For details of
front-panel media types, see page 3-3. To find out the plotter’s current type of
media setting, see page 7-2.
Note that some media types are not recommended for color plots with large area
fills. See page 3-5.
If the Plot Is Too Dark or the Color Too Saturated
You can make a global adjustment to the amount of black ink used (which
affects most colors too) by adjusting the Lightness setting. See page 5-8.
9-19
Troubleshooting
Solving Print-Quality Problems
If There Is Pronounced Banding in Area Fills
Some banding is normal, especially in dark or dense area fills. If the banding is
unacceptable, try the following:
Make sure you are using HP media.
Try changing the Print Quality setting.
If the banding is in a black or gray area, then try reducing the percentage of
black in grayscales, either in your software or in the plotter’s palette. For
details of how to do this using the plotter’s palette, see page 5-3.
Force the automatic cartridge alignment procedure by reseating a print
cartridge.
Try accuracy calibration.
Adjust the drying time, see page 3-22.
If the problem persists, replace the print cartridge(s). See page 3-26.
If Ink Smears After You Remove a Plot
Use HP media for best quality.
A
This can be caused by extreme environmental conditions. For environmental
specifications, see page 11-4.
With roll media, the plotter automatically allows a suitable ink-drying time
before cutting the roll and dropping the plot in the media bin. To allow for
extremely dry or humid environments within the specification, see page 3-22.
With sheet media, you need to allow for ink-drying time before removing the
sheet. For recommended ink-drying times, see page 3-22. For example, with a
best-quality monochrome plot on opaque bond, you should wait about 90
seconds before unloading the sheet.
Handle media by the edges. If possible, wear gloves when you handle film. Skin
oils can interact with ink and cause it to smear.
9-20
Troubleshooting
Solving Front-Panel Problems
Solving Front-Panel Problems
!
If the Access Cartridge(s) Key Does Not Work
Make sure the plotters’ window is closed before you press Access
Cartridge(s).
If None of the Front-Panel Keys Work
Turn the plotter off and then on again. If the problem persists, have your plotter
serviced.
If Page Format/Rotate Does Not Work
Your plot file may be too big for the plotter’s buffer, and you may need to
consider obtaining a memory expansion module. For information on memory
expansion modules, see page 11-14.
The plotter cannot rotate raster images. If your plots contain raster data
(typically, images with heavy area fill and shading that you have scanned into
your software) you will not be able to rotate the plot.
The plotter cannot rotate any file sent using the Microsoft Windows driver
supplied with the plotter, as they contain raster images.
If a Display Message Will Not Clear
Look up the message in chapter 10. The message description may help you
understand and resolve the problem.
If looking up the message did not help, press Enter. If that does not work, turn
the power off, then on again. If the message still displays, have the plotter
serviced. If the message says “System Error” and has an alphanumeric code,
refer to the next explanation.
9-21
Troubleshooting
Solving Front-Panel Problems
If a “System Error” Message Is Displayed
Press Enter. If the message does not clear, turn the plotter off, then on again to
try to clear the system error. If media appears to be jammed, clear it. If the
message is still displayed, record the alphanumeric code and have the plotter
serviced. Report the code to the service technician; knowing the code number
will help the technician resolve the problem.
If an “Out Of Memory/Data Was Lost” Message Is Displayed
The current plot is too large for the plotter’s buffer. To print this plot you will
have to install additional memory. For information on memory expansion
modules and memory usage, see page 7-10.
9-22
Troubleshooting
Solving miscellaneous problems
Solving Miscellaneous Problems
?
If the Plotter Does not Plot
You may have a power problem. If there is no activity at all from the plotter,
and no lights on the front panel, check that the power cable is connected
correctly and that there is power available at the socket.
You may have a problem with your application driver. Is your software
configured for this plotter? For general advice, see page 1-35. For advice
specific to your software, see either the documentation supplied with the driver
or a relevant Software Application Note supplied with your plotter.
The file may be too big for the plotter’s memory.
– Look on your computer screen for any error message: some drivers, for
example the Microsoft Windows driver supplied with your plotter, allow you
to choose a different printing mode and try to send the file again.
– If no other printing mode is available, or if your file still does not print, you
may need to consider obtaining a memory expansion module. For informa-
tion on memory expansion modules, see page 11-14.
If you continue to have problems, see “Getting help” on page 9-25.
If the Plotter Seems Too Slow
Did you specify Best Print Quality on the front panel? Best quality plots are
produced more slowly. See page 5-11.
Did you specify the right media type when loading the media? For details of
front-panel media types, see page 3-3. To find out the plotter’s current type of
media setting, see page 7-2.
If you are using the Microsoft Windows driver shipped with the plotter, check
the settings in the “Print Setup / Options” dialog box, where some of the
settings impact printing speed. If in doubt, use the on-screen help system.
Is Sharp lines set to Auto on the front panel or in your driver? If so, setting it to
Off will speed up your plotter but may reduce the quality of your plot. See
page 5-14
750C Plus
9-23
Troubleshooting
Solving Miscellaneous Problems
If the Plotter Waits Too Long to Plot a Nest
Change the Nest wait setting. See page 6-12.
If the Plotter Performs the Cartridge Alignment Routine
Unexpectedly
This is a normal plotter operation. The plotter will align the cartridge(s) every
time you replace, or even reseat, a cartridge, whether or not it is new.
If the Bail (Black Metal Bar) Does Not Lower All the Way
If the the bail (the black metal bar just inside the plotter’s window) will not
lower all the way, check for obstructions underneath it.
Make sure the cutting carriage is pushed all the way to the right.
9-24
Troubleshooting
Getting Help
Getting Help
Hewlett-Packard has support services available to help you in case you have a
problem with your plotter.
For a list of the support services available, refer to the Hewlett-Packard
Support Services booklet shipped with this plotter.
What to Do Before You Call
1 Review the troubleshooting suggestions:
in this chapter,
in the relevant driver documentation supplied with this plotter (for users of
AutoCAD and Microsoft Windows applications),
in any relevant Software Application Note supplied with this plotter.
2 Plot the sample plot as explained on page 1-24. If the sample plot works and does
not display the problems you have found with your own plots, then the problem is
probably not with your plotter.
3 If the problem appears to be related to your software application, first contact your
software vendor.
4 If you still have difficulty, refer to the HP Support Services booklet shipped with
this plotter. This document contains a comprehensive list of various support
services available to help solve plotter problems.
5 If you do call one of the Hewlett-Packard offices, please have the following
information available to help us answer your questions more quickly:
The plotter you are using.
The computer you are using.
Any special equipment or software you are using (for example, spoolers,
networks, switch-boxes, modems, or special software drivers).
The cable you are using (by part number) and where you purchased it.
The type of interface used on your plotter (RS-232-C, parallel, or modular).
The software name and version you are currently using.
If a Repair Is Needed
Contact the Hewlett-Packard dealer or HP Sales and Support Office nearest to you
for complete service information.
9-25
9-26
10
Front-Panel Messages
10-1
Front-Panel Messages
Front-Panel Messages
This is a list of all possible messages in the front-panel display. If you need to do
something, it is shown in italics in the Explanation and Action column.
The messages are listed in alphabetical order.
Message
Explanation and Action
Alignment error
Continue
The alignment procedure has failed. Check that an opaque media is loaded.
Press ↓ to continue and force the automatic alignment procedure again by
reseating any of the print cartridges. Do not lift the window while cartridge
alignment is being performed.
!
Calibrate error
Continue
The calibration plot was loaded incorrectly and it could not be measured. Press ↓
to continue, then reload the plot for measurement. Follow front panel instructions.
!
!
Calibration done
Continue
Accuracy calibration is complete. Press ↓ to continue.
Close roll cover
Continue
Rewind the media to take up any slack in the roll, close the roll cover, then press
↓ to continue.
!
!
Press ↑ to create the pattern for automatic calibration.
Press ↓ to start the automatic calibration.
Create pattern
Measure pattern !
Edge not found
Reload media
The plotter could not find edge of media during loading procedure. Check the
leading edge of the media for unevenness or tears; cut a straight edge, if
necessary, and reload. Be sure to position the right edge along the perforated line
on the entry platen when loading.
Lift lever
Lift the lever at the right of the plotter.
Load arrow edge
print side down
Remove calibration plot, turn it so that the edge with arrows printed on it is print
side down, then load that edge into the plotter.
Load cancelled
Remove media
You pressed the Cancel button while media loading was in progress. Remove
media.
Load error
Remove media
You inserted media with the media lever raised. Lower the lever and reload the
media.
Load media
Load media to proceed with cartridge alignment.
to align cartridges
Lower lever
after aligning
When you have finished aligning the roll media as instructed, lower the lever at
the right of the plotter.
10-2
Front-Panel Messages
Message
Explanation and Action
Lower lever
to continue
You lifted the media lever while the processor was busy. Lower the lever to
continue.
Lower window
to continue
You opened the window while the processor was busy. Close the window to
continue.
Media too small
The media you loaded for accuracy calibration or cartridge alignment is too small.
Reload appropriate media. See page 7-5.
Mispositioned
Reload roll
The roll is mispositioned. Reload media.
Mispositioned
Reload sheet
The sheet is mispositioned. Remove it and reload it with the right edge no more
than 0.2 inches (0.5 cm) from either side of the perforated line on the entry platen.
MIO data error
The modular interface is incorrectly configured. Press Enter to clear the message
from the front panel display. Recheck the MIO configuration settings.
MIO error
Communication
Break
The flow of data from the computer to the plotter was prematurely stopped (e.g.,
by turning off the computer before all data is sent). Press Enter to clear the
message from the front panel display.
Open window to
Lift the window to access the cartridge(s).
access cartridge(s)
Out of memory
Data was lost
The current plot is too large for the plotter’s buffer. Install additional memory to
plot this drawing.
Grasp the left and right free edges of the roll media and pull toward you until the
media is taut. At the same time, align the left and right edges of the media so that
they are flush with the left and right edges of the roll.
Pull # / Align $
edges to roll
Remove media
The ink is dry. Remove the calibration plot the plotter just produced. Press ↓ to
continue with accuracy calibration.
Remove media
Lower lever
You have attempted to load media while the lever at the right of the plotter was
raised. Remove the media, lower the lever, and reload media with the lever down.
Replace cartridge(s)
JJJJ
The cartridge indicated has a clogged nozzle. Replace it to continue.
The cartridge indicated is badly seated. Reseat it to continue.
Roll media is misaligned (skewed). Reload media.
Reseat cartridge(s)
JJJJ
Roll misaligned
Reload roll
RS-232 error
Baud, parity
The RS-232-C interface is configured incorrectly. Press Enter to clear the
message from the front panel display. Check the baud rate and parity settings in
the front panel, in the hardware configuration, and in your software to be sure they
are all compatible.
10-3
Front-Panel Messages
Message
Explanation and Action
Service cartridge(s)
Cartridge Check is on and an error has been detected. Press ↑ if you want to
service the cartridge(s) (replace or reseat). Press ↓ if you want to continue without
servicing the cartridge(s).
Continue
!
Press ↑ to load sheet media.
Press ↓ to load roll media.
Sheet load
Roll load
!
!
Sheet misaligned
Reload sheet
Sheet media is misaligned (skewed). Remove it and reload it so that the left and
right edges being loaded into the plotter are square. The leading edge must also
be straight.
Sheet / Roll?
Reload media
D Either: You have chosen Sheet mode while loading roll media. Reload media.
D Or: You have loaded a sheet more than 51 inches (130 cm) long. Trim sheet
and reload.
STATUS
Accessing
cartridge(s)
You have pressed the Access cartridge(s) button. The cartridge carriage is moving
to the service cartridge(s) position so you can access it.
STATUS
The plotter is aligning the cartridge(s).
Aligning cartridge(s)
STATUS
Cancelling
You have pressed the Cancel button and the plotter is in the process of cancelling
the procedure. Continue when this message is no longer displayed.
STATUS
Checking media
The plotter is checking to see if media is properly positioned with respect to the
perforated line of the entry platen.
STATUS
The plotter is performing calibration.
Calibrating
STATUS
The ink on your plot is drying. Wait before removing the plot. If you remove it
Ink drying (xx m xx s) before the indicated time has passed, avoid smearing the ink.
STATUS
The plotter is loading roll media.
Loading roll
STATUS
The plotter is loading sheet media.
Loading sheet
STATUS
You are using the plotter more intensively than the recommended duty cycle and
Maintenance advised should contact your local HP dealer or HP service engineer to arrange a service.
For the duty cycle specification, see page 11-4. If you choose to not to call for
service, you may continue to use the plotter as normal, but may encounter
operational or print-quality problems.
STATUS
The plotter is measuring the calibration plot you just loaded.
Measuring
10-4
Front-Panel Messages
Message
Explanation and Action
STATUS
The cartridge carriage is returning to its station at the left of the plotter.
Returning cartridge(s)
STATUS
The plotter is trimming the edge of roll media.
Roll feed edge trim
STATUS
Initializing
The plotter is doing an internal check during power-up.
The plotter has received a file, is ready to print, but has no media loaded.
The plotter is printing.
STATUS
Out of media
STATUS
Printing
STATUS
Printing (Special)
The plotter is printing with a special print mode controlled by your software rather
than by the plotter.
STATUS
The plotter is ready for you to load media.
Ready for media
STATUS
Ready
The plotter is ready to print.
STATUS
The plotter is receiving or has received plot data.
Receiving
STATUS
Testing cartridge(s)
The plotter is testing the cartridge(s) for problems, i.e., clogged cartridge or bad
electrical connection (improper seating).
Switch power off
Turn off the plotter. The cartridge carriage cannot move. The plotter may be
Check cartridge path jammed with media. Check the media path and clear it if necessary. Then turn on
the plotter.
Switch power off
Check paper path
Turn off the plotter. The drive roller cannot move or the roll feed spindle cannot
freely rotate. The plotter may be jammed with media. Check the media path and
clear it if necessary. Then turn on the plotter.
System error
XXXXXX
An internal error has occurred and a system error number is displayed. Press
Enter; this may clear the error and allow you to continue. If you cannot continue,
turn off the plotter, then turn it on again. If you still see the system error message,
record the system error number and have the plotter serviced. For support
details, see page 9-25.
Wrong cartridge type You have loaded one or more incompatible cartridges. Replace the cartridges with
those appropriate for this plotter.
10-5
10-6
11
Plotter Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
Interface Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10
Ordering Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13
Reference
11-1
Reference
Plotter Specifications
Plotter Specifications
C4705A and C4708A = D/A1-size plotter.
C4706A and C4709A = E/A0-size plotter.
Functional Specifications
Cartridges
HP DesignJet 700, one black. For part number, see page 11-15.
700
HP DesignJet 750C Plus. yellow, cyan, magenta and black. For part numbers, see
page 11-15.
750C Plus
Media sizes
Width (carriage axis)
Minimum
Length (paper axis)
Minimum
Maximum
Maximum
E/A0-size plotter
Maximum length
of long axis plot
on roll media:
15.2 m (50 ft)
917 mm (36.1 in)
190 mm (7.5 in)
210 mm (8.3 in)
Color
625 mm (24.6 in)
1.32 m (52 in)
sheet media
D/A1-size plotter
Media types
Monochrome
See also Supplies
Source catalog and (in
Europe and USA)
Media Reference
Guide
Opaque bond
Translucent bond
Natural tracing paper
Vellum
Opaque bond (CAD drawings only)
1
Natural tracing paper
1
Vellum
For alternative names,
HP commercial names
and physical
characteristics of
these media types,
see chapter 3.
Coated paper
Matte film
Coated paper
Matte film
Clear film
Clear film
Heavy coated paper
High-gloss photo paper
Heavy coated paper
High-gloss photo paper
Semi-gloss photo paper
High-gloss film
2
2
750C Plus Semi-gloss photo paper
2
High-gloss film
1
CAD drawings only and HP media only.
2
Monochrome drawings can be plotted on glossy media providing the color cartridges are
loaded.
Note. From time to time, new media types may become available. For up-to-date information,
please contact your HP dealer or local HP Sales and Support Office.
11-2
Reference
Plotter Specifications
Functional Specifications
Margins
Normal
Smaller (roll media only)
For plotting area
(media size minus
margins), see
page 11-6
Leading edge:
Trailing edge:
Sides:
17 mm (0.67 in)
17 mm (0.67 in)
5 mm (0.2 in)
10 mm (0.39 in)
10 mm (0.39 in)
5 mm (0.2 in)
All measurements ꢀ 2 mm (0.08 in).
Print Quality
Resolution
Resolution
Fast print quality:
300 x 300 dpi.
600 x 600 dpi.
600 x 600 dpi.
Color/Mono set to: Color
700
Normal print quality:
Best print quality:
Color/Mono set to: Mono
Fast print quality:
Normal print quality:
Best print quality:
300 x 300 dpi.
600 x 600 dpi.
600 x 600 dpi.
Fast print quality:
300 x 300 dpi.
1
1
750C Plus
Normal print quality: 300 x 300 dpi.
Best print quality:
600 x 600 dpi.2
Accuracy
ꢀ 0.38 mm (0.015 in) or ꢀ 0.2% of the specified vector length, whichever is greater,
(Maximum
at 23_C (73_F), 50–60% relative humidity, on HP Matte Film.
accumulated error)
Programming
languages
HP-GL (7586B), HP-GL/2, HP RTL, PJL
supported
1
Except for glossy media types, on which the resolution is always 300 dpi.
2
Addressable dpi (depending on the type of image your application software has created).
Only on coated paper, matte film and opaque bond media.
Physical Specifications
Weight
Length
(unpacked)
Depth
(unpacked)
Height
(unpacked)
(packed)
With stand
E/A0-size plotter
D/A1-size plotter
Without stand
E/A0-size plotter
D/A1-size plotter
60 kg (132 lb)
49 kg (108 lb)
1370 mm (54.0 in) 675 mm (26.6 in)
1072 mm (42.2 in) 675 mm (26.6 in)
1200 mm (47.3 in)
1200 mm (47.3 in)
42 kg (93 lb)
32 kg (71 lb)
11-3
Reference
Plotter Specifications
Environmental Specifications
Operational
Mechanical and electrical:
0 to 55_C (32 to 131_F)
@ 5-95% relative humidity
With cartridges and media:
15 to 35_C (59 to 95_F)
@ 20-80% relative humidity
For optimal print quality and media
handling:
15 to 30_C (59 to 86_F)
@ 20-80% relative humidity
Storage
Plotter and media:
–40 to 70_C (–40 to 158_F)
@ 20-80% relative humidity
Cartridges:
–40 to 60_C (–40 to 140F_)
@ 20-90% relative humidity
Power Specifications
Source
100–240V ac ꢀ 10%. Autoranging.
50–60 Hz
Frequency
Consumption
140 W max. (2.0 A max.)
Energy Star rating Maximum power in idle state: 45 watts
(USA)
Acoustic Specifications
Operating sound pressure
Idle sound pressure
42 dB(A)
(From a one-meter bystander position and
with Print Quality set to Best.)
<20 dB(A)
Duty Cycle
Recommended
maximum number
of plots per day
Medium density E/A0 CAD plots:
Medium density E/A0 image plots:
20
12
11-4
Reference
Plotter Specifications
EMC (Electromagnetic Compatibility) Specifications
Canada
Canadian Department of Communications, Radio Interference Regulations
Class B compliant.
European Union
89/336/EEC EMC Directive compliant.
B
Meets EN 55022 Class
emission limits, prEN 55024Ć2
ESD, prEN55024Ć3 Radiated Immunity, prEN 55024Ć4
Fast Transients.
Japan
Registered VCCI Class 2.
RRL certified
Korea
South Africa
USA
SABS licensed
Federal Communications Commission certified.
Class
B
CFR 47 Part 15
computing device.
Safety Specifications
Information Technology Equipment (ITE),
Movable,
Class I,
Plugable Type A,
Installation CategorIyI,
Pollution Degree 2.
For indoor controlled office environments use.
Canada
Canadian Standards Association Certified" ITE, CSA C22.2 No.950
European Union
Mexico
73/23/EEC Low Voltage Directive compliant.
Meets EN 60950
DGN, NOM019-SCFI-1993 certified
Norway
NEMKO approved,
EN 60950, EMKO TSE(74)DK207/94
USA
Underwriters' Laboratories
Listed" ITE, UL 1950
11-5
Reference
Plotter Specifications
Plotting Area (= Media Size Minus Margins).
Media size (and
orientation of
media)
Plotting area (width x height)
by orientation of drawing
inches
landscape
9.66 x 8.1
millimeters
portrait
landscape
portrait
ANSI media
A
A
B
B
C
C
D
D
E
A
A
B
B
C
C
D
D
(portrait)
8.1 x 9.66
245 x 205
269 x 182
397 x 269
421 x 245
524 x 421
549 x 398
829 x 548
854 x 525
205 x 245
(landscape)
(portrait)
10.6 x 7.16 7.16 x 10.6
15.7 x 10.6 10.6 x 15.7
16.6 x 9.66 9.66 x 16.6
20.7 x 16.6 16.6 x 20.7
20.6 x 15.7 15.7 x 20.6
32.7 x 21.6 21.6 x 32.7
33.6 x 20.7 20.7 x 33.6
42.7 x 33.6 33.6 x 42.7
182 x 269
269 x 397
245 x 421
421 x 524
398 x 549
548 x 829
525 x 854
(landscape)
(portrait)
(landscape)
(portrait)
(landscape)
(portrait)
1084 x 854 854 x 1084
Architectural media
(portrait)
10.7 x 8.60
8.6 x 10.7
271 x 219
295 x 195
423 x 295
447 x 271
576 x 447
600 x 423
880 x 600
904 x 576
219 x 271
195 x 295
295 x 423
271 x 447
447 x 576
423 x 600
600 x 880
576 x 904
(landscape)
(portrait)
11.6 x 7.66 7.66 x 11.6
16.7 x 11.6 11.6 x 16.7
17.6 x 10.7 10.7 x 17.6
22.7 x 17.6 17.6 x 22.7
23.6 x 16.7 16.7 x 23.6
34.7 x 23.6 23.6 x 34.7
35.6 x 22.7 22.7 x 35.6
40.7 x 29.6 29.6 x 40.7
46.7 x 35.6 35.6 x 46.7
10.3 x 7.87 7.87 x 10.3
11.3 x 6.93 6.93 x 11.3
15.2 x 11.3 11.3 x 15.2
16.1 x 10.3 10.3 x 16.1
22.0 x 16.1 16.1 x 22.0
23.0 x 15.2 15.2 x 23.0
31.8 x 23.0 23.0 x 31.8
32.7 x 22.0 22.0 x 32.7
45.5 x 32.7 32.7 x 45.5
(landscape)
(portrait)
(landscape)
(portrait)
(landscape)
E1 (portrait)
(portrait)
1033 x 752 752 x 1033
1185 x 904 904 x 1185
E
ISO media
A4 (portrait)
263 x 200
287 x 176
386 x 287
410 x 263
560 x 410
584 x 386
807 x 584
831 x 560
200 x 263
176 x 287
287 x 386
263 x 410
410 x 560
386 x 584
584 x 807
560 x 831
A4 (landscape)
A3 (portrait)
A3 (landscape)
A2 (portrait)
A2 (landscape)
A1 (portrait)
A1 (landscape)
A0 (portrait)
1155 x 831 831 x 1155
For margins, see page 11-3. This table is calculated with normal margins.
11-6
Reference
Interface Specifications
Interface Specifications
Below are the parallel and serial interface specifications.
Pin Wire/Signal Name
Strobe
Source
computer
both
Parallel (Bi-Tronics/Centronics)
Interface
1
The connector on the plotter is
36-pin female.
2 ... 9 D0 ... D7 (data lines)
10 Ack
plotter
Most existing parallel cables support
Bi-Tronics communication, but for
use with this plotter, the cable must
meet the specification in this table.
11 Busy
plotter
12 PError
plotter
13 Select (SelectOut)
14 AutoFd
plotter
computer
16 GND
19 ... 30 GND
31 Init
computer
plotter
32 Fault
36 SelectIn
computer
Serial (RS-232-C) Interface
Pin Wire/Signal Name
Source
1
2
3
4
6
7
Protective Ground
Transmitted Data
Received Data
Request to Send
Data Set Ready
Signal Ground
The connector on the plotter is 25-pin
female.
DTE
DCE
DTE
DCE
The plotter is configured as DTE (data
terminal equipment).
Data is transmitted on Pin 2 and
received on Pin 3.
20 Data Terminal Ready
DTE
11-7
Reference
Interface Cables
Interface Cables
Cables for PCs
Interface type
HP part
number
Cable length
Connector type at
computer end of cable
Computer
Parallel (Bi-Tronics/Centronics) Interface
All
C2951A
C2950A
3.0 m (9.8 ft)
2.1 m (6.9 ft)
25-pin male
25-pin male
Serial (RS-232-C) Interface
HP Vectra or HP 24541A/B serial-interface
24542G
3.0 m (9.8 ft)
9-pin female
card (9-pin connector)
IBM AT and compatibles using 9-pin serial
connectors
HP Vectra PC with HP 24541A/B dual serial- 13242G
5.0 m (16.4 ft)
25-pin male
interface card using the 25-pin connector
IBM PC, PC/XT, PC/AT, PS/1, PS/2 and
compatibles
C2913A
17255D
1.2 m (3.9 ft)
1.2 m (3.9 ft)
25-pin female
25-pin female
Cables for Macintoshes
Interface type
HP part
number
Cable length
Connector type at
computer end of cable
Computer
Serial (RS-232-C) Interface
Apple Macintosh Plus, SE, II Series, Classic, 17302A
LC family, Quadra family, PowerBook,
PowerMac
1.5 m (4.9 ft)
8-pin male mini-DIN
11-8
Reference
Interface Cables
Cables for Unix systems
Interface type
HP part
number
Cable length
Connector type at
computer end of cable
Computer
Parallel (Bi-Tronics/Centronics) Interface
All
C2951A
C2950A
3.0 m (9.8 ft)
2.1 m (6.9 ft)
25-pin male
25-pin male
Serial (RS-232-C) Interface
HP 9000 workstations using 9-pin
connectors.
24542G
13242G
3.0 m (9.8 ft)
5.0 m (16.4 ft)
9-pin female
HP Apollo workstation using an SPE
(Serial/Parallel Expansion) option and
supplied adapter cable
25-pin male
Sun workstation
13242G
5.0 m (16.4 ft)
25-pin male
Note: You may need a Sun serial adapter
cable to convert the DIN connector found on
certain Sun SPARC stations to the 25-pin
connector on the HP cable. Contact your
Sun dealer for part numbers.
11-9
Reference
Regulatory Notices
Regulatory Notices
To Obtain a Material Safety Data Sheet (MSDS)
You can obtain current Material Safety Data Sheets for the print cartridges used in
the plotter (HP Part numbers 51644C [cyan], 51644M [magenta], 51644Y [yellow]
and 51645A [black]) by mailing a request to this address:
Hewlett-Packard Customer Information Center, 19310 Pruneridge Avenue,
Dept. MSDS, Cupertino, CA 95014, U.S.A.
Electromagnetic Compatibility (EMC)
FCC Statement
(U.S.A.)
The U.S. Federal Communications Commission (in 47 cfr 15.105) has specified
that the following notice be brought to the attention of users of this product.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try and correct the
interferences by one or more of the following measures:
Reorient the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
The user may find useful the following booklet prepared by the FCC: “How to
Identify and Resolve Radio,TV Interference Problems”. This booklet is available
from the US Government Printing Office, Washington, DC 20402, Stock No.
004,""",""' (),(
Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to this
equipment not expressly approved by the Hewlett-Packard Company, may cause
harmful interference and void the FCC authorization to operate this equipment.
C A U T I O N
11-10
Reference
Regulatory Notices
DOC statement
(Canada)
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la classe B prescrites dans le
Règlement sur le Brouillage Radioélectrique édicté par le ministère des
Communications du Canada.
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
VCCI-2 (Japan)
Korean EMI
statement
Geräuschemission
(Germany)
LpA < 70 dB
am Arbeitsplatz
im Normalbetrieb
nach DIN 45635 T. 19
Telecommunications Statement
Tele-
The HP DesignJet 700 and the HP DesignJet 750C Plus plotters, models C4705A,
C4706A, C4708A and C4709A are approved under Approval Number
NS/G/1234/5/100003 for indirect connection to public telecommunication systems
within the United Kingdom.
communications
General Approval
(UK)
11-11
Reference
Regulatory Notices
DECLARATION OF CONFORMITY
according to ISO/IEC Guide 22 and EN 45014
Manufacturer’s Name:
Hewlett-Packard Española S.A.
Manufacturer’s Address:
Hewlett-Packard Española S.A.
BARCELONA DIVISION
Avda. Graells, 501
08190 Sant Cugat del Vallès
Barcelona, Spain
declares that the product
Product Name:
InkJet Plotter
Model Numbers:
Product Accessory:
HP C4705A, HP C4706A, C4708A, C4709A
HP JetDirect network interface card (2)
conforms to the following Product Specifications:
Safety:
IEC 950: 1991 + A1, A2 / EN 60950 (1992) + A1, A2
CSA C22.2 No. 950 (1993)
UL 1950 (1993)
EMKO-TSE(74)DK207/94
NOM-019-SCFI-1993
EMC:
CISPR 22: 1993 / EN 55022 (1994): Class B(1)
EN 50082-1 (1992)
IEC 801–2: 1991 / prEN 55024–2 (1992): 4KV CD
8KV AD
IEC 801–3: 1984 / prEN 55024–3 (1991): 3 V/m
IEC 801–4: 1988 / prEN 55024–4 (1992): 1KV Power Lines
0.5KV Signal Lines
FCC Part 15 – Class B / DOC–B / VCCI–2 / RRL–A
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the
EMC Directive 89/336/EEC, and carries the CE marking accordingly.
(1)
The product was tested with a Hewlett-Packard system,
consisting of: a Vectra 486/33M personal computer, VGA monit
keyboard, mouse, and a Printer DeskJet 550C as the second peri
(2)
Product options with interface cards exhibit Class A operatio
Sant Cugat del Vallès (Barcelona), September 1st, 1996
Quality Engineering Manager
European Contact:
Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department ZQ/Standards
Europe, Herrenberger Strasse 130, D-71034 Boeblingen, Germany (fax: (+49) 7031 143143).
11-12
Reference
Ordering Accessories
Ordering Accessories
HP Part
Number
Cables
See page 11-8
Documentation
User’s Guide and Quick Reference Guide
Chinese
C4705-60030
C4705-60021
C4705-60025
C4705-60024
C4705-60027
C4705-60028
C4705-60022
English
French
German
Italian
Japanese
Korean
Portuguese C4705-60029
Spanish C4705-60026
Taiwanese C4705-60023
Software Application Notes
English
Multi
C4705-90006
(1)
Hewlett-Packard Support Services
(2)
HP-GL/2 and RTL Programmer’s Reference Guide English
5959-9733
(2)
The Product Comparison Guide for HP-GL/2 and English
HP RTL Peripherals
5959-9734
PJL Technical Reference Manual
English
5961-0938
1
This item is updated regularly. For details of the latest version available, please contact your HP
dealer or sales representative.
2
See note on page 11-16.
11-13
Reference
Ordering Accessories
To achieve the best performance from your plotter, we recommend you only use
genuine Hewlett-Packard accessories and supplies, whose reliability and
performance have been thoroughly tested to give trouble-free performance. For
Example:
HP drivers are developed to support all the latest features and to optimize print
quality and your plotters performance.
HP memory expansion modules are thoroughly tested to give you maximum
performance.
HP ink cartridges and media supplies are developed for optimal print quality.
Drivers
HP Part
Number
Latest versions of the following were shipped with
this plotter:
(1)
(1)
HP plotter drivers for AutoCAD for DOS and
AutoCAD for Windows
HP plotter driver for Microsoft Windows
Available as options are:
C4707A
PostScript Upgrade Kit
(ROM SIMM and driver)
Media Supplies
(1)
(1)
Supplies Source Catalog
(The latest edition was shipped with this plotter)
Media Reference Guide
(The latest edition was shipped with this plotter in
Europe and USA only.)
Memory Expansion Modules
All SIMMs on the right are 72-pin, 36-bit.
4/8 MB: 80 nanoseconds.
16/32 MB: 70 nanoseconds
4 MB
8 MB
16 MB
C3132A
C3133A
D2297A or
C3146A
For up-to-date details of any memory expansion
modules other than those listed here, contact your
local authorized HP dealer.
32 MB
D3578A
1
This item is updated regularly. For details of the latest version available, please contact your HP
dealer or sales representative, or, for drivers, use one of the support resources for your area listed in
the Hewlett-Packard Support Services Booklet shipped with your plotter.
11-14
Reference
Ordering Accessories
HP Part
Number
Network Interface
Hewlett-Packard supply a variety of internal or external, single or multi port
Network Interfaces which are constantly being upgraded. Contact your
Dealer or Hewlett-Packard support services for current HP part numbers
suitable for your application.
Print Cartridges
Yellow
Cyan
51644Y
51644C
51644M
51645A
Although other cartridges may appear to fit in the
stalls, use only these part numbers.
Magenta
Black
Spindle Assembly
E/A0-size
C3173A
C3172A
D/A1-size
11-15
Reference
Ordering Accessories
HP-GL/2 and HP RTL Programming Information
The HP-GL/2 and HP RTL Reference Guide provides complete explanations and
examples of the HP-GL/2 and HP RTL graphic and interface instructions. If you
are writing an HP-GL/2 or RTL driver for your plotter, you will find this guide an
invaluable source of general instruction information. It is published by
Addison-Wesley Publishing Company and you can can order it through most book
stores (ISBN 0-201-63325-6).
For specific parameter information, refer to The Product Comparison Guide for
HP-GL/2 and HP RTL Peripherals, which you can order through your HP Sales
office.
How to Order Supplies and Accessories
You can order supplies and accessories in any of the following ways:
Call your local authorized HP dealer.
Contact your local HP Sales and Support office.
Refer to the Hewlett-Packard Support Services booklet that was supplied with
your plotter. In the United States, the Direct Ordering number
is (800) 538 8787.
11-16
12
Glossary
12-1
Glossary
ac Alternating current.
CMYK Cyan, magenta, yellow and black. The
colors of the plotter’s four inks, and also a standard
addressable dpi A resolution higher than nominal color model.
value of the cartridges, giving a finer grid on which
the plotter can selectively position dots and improve coated paper Good quality paper coated on one
print quality.
side for inkjet printing.
ANSI size An American standard paper size; e.g.
dc Direct current.
D, E, etc.
default A value or condition that is assumed if no
application The software you use.
other value or condition is specified.
bail The black metal bar inside the plotter, which
holds the media in place.
device An external item connected to the
computer: printer, plotter, tape drive etc. Your
HP DesignJet is a device.
baud rate The data transmission rate in a serial
interface between a computer and a device, in bits
per second.
dpi Dots per inch, a measure of print resolution.
driver The software that controls the
communication between a computer and a device.
Bi-tronics A standard for the parallel interface
between computer and device, compatible with
Centronics.
front panel The control panel on the front of the
plotter.
CAD Computer-aided design.
front-panel menus The options in the front-panel
display.
cartridge Print cartridge, containing ink.
GIS Geographical information system (mapping
software).
Centronics A standard for the parallel interface
between computer and device. Compatible with
Bi-tronics.
graphics language A programming language
telling a print device how to output graphic data.
clear film See-through, polyester media type.
grayscale Shades of gray to represent colors.
clipping Losing part of a drawing at the edges.
high-gloss film A glossy, opaque, polyester media
type.
12–2
Glossary
high-gloss photo A glossy, opaque photographic
media The material, usually paper, onto which the
paper.
plotter prints.
HP-GL One of Hewlett-Packard’s standard
graphics languages for plotters and printers.
Produces vector data. Forerunner to HP-GL/2.
media bin The media catcher situated below the
plotter.
MIO Modular input/output. Refers to the
HP-GL/2 One of Hewlett-Packard’s standard
graphics languages for plotters and printers.
Produces vector data. Newer than HP-GL.
plotter’s network interface.
nesting Placing two or more plots side-by-side on
the media to avoid waste.
I/O Input/output. The transmission of data
between a computer and a device.
opaque bond A matte paper media.
inked area The smallest rectangle that contains
palette A set of logical pens defined by color and
all the content of the drawing, while maintaining the width.
drawings relative dimensions.
PJL Printer job language. A programming
ISO size An international standard paper size; e.g. language that controls jobs going to a printer or
A1, A2, etc.
plotter.
JIS size A Japanese standard paper size.
LAN Local area network.
PML Printer management language.
parallel interface A type of interface between
computer and device. Generally faster than a serial
interface.
long-axis plotting Plotting a page whose X-axis
(the axis vertical to the plotter as you look at it from
the front) is longer than a standard page size.
pen Even though the plotter has no physical pens,
the lines it draws match the attributes of a pen.
margin The space around the page added by the
plotter to separate one page from another and to
avoid printing right to the edge of the media.
platen The exterior part of the plotter on which
the media rests before going into the media-entry
slot.
matte Not glossy.
plotting area Page size minus margins.
matte film Opaque, polyester media type (not
glossy).
12–3
Glossary
PostScript A standard page markup language,
commonly used by graphics and desktop publishing
software applications.
tracing paper A semi-opaque matte paper type.
translucent bond A semi-opaque matte paper
type.
queueing Placing each page of each file received
by the device in chronological order of receipt
(unless changed by prioritizing), before and after
printing.
vector A line. A method for defining an image,
in terms of lines rather than dots. Vector data
typically needs less memory than raster data.
parity An error-checking method in a serial
vellum Cotton-fiber-based, semi-opaque matte
interface between a computer and a device.
media type.
raster A method for defining an image, in terms
X-axis The vertical axis, as you look at the plotter
of dots rather than lines. Raster data typically needs from the front.
more memory than vector data.
Y-axis The horizontal axis, as you look at the
plotter from the front.
RGB Red, green and blue. A standard color
model.
RS-232-C A serial interface standard.
RTL One of Hewlett-Packard’s standard graphics
languages for plotters and printers. Produces raster
data.
ROM SIMM A physical module containing
read-only data, to provide plotter upgrades. They
are installed in the back of the plotter.
semi-gloss photo A semi glossy, opaque
photographic paper.
serial interface A type of interface between
computer and device. Generally slower than a
parallel interface.
spindle The rod which holds the roll of media.
12–4
Index
A
environmental specifications, 11-4
ink level, 3-26
loading, 1-20–1-23
ordering, 11-15
part numbers, 11-15
problems, 9-18
current configuration plot, 2-3
cutting
and margins, 4-6
immediately after plotting, 6-2
problems with, 9-5–9-6
Access Cartridge(s) key, 1-21, 3-28
problems, 9-7
accessories, 1-5–1-6
list, 11-13
ordering, 11-16
accuracy, specification, 11-3
acoustic specifications, 11-4
action keys, 2-2
addressable 600 dpi, Sharp lines, 5-15
addressable dpi, 5-14
Apollo, cables to connect, 11-9
Apple, cables to connect, 11-8
archiving plots, 3-9
area fill problems, 9-19
AutoCAD, drivers, 11-14
automatic cutter, problems with,
9-5–9-6
problems with, 9-7
removing tab, 1-22, 3-30
replacing, 3-26–3-31
supplied, 1-5
choosing media, 3-2–3-7
cleaning the plotter, 8-2
clearing the media path, 3-25
clipped plot, 9-12
clipping
and page size, 4-5
and Rotate, 4-8
CMYK, 5-4
D
darkness of plot, adjusting, 5-8
Declaration of Conformity (EC),
11-12
default page margins, 4-6
Define palette, 5-5
Delete page, 6-7
demonstration plot, 1-24–1-26
Demos, 1-25
device lists, 1-38
dimensions of plotter, 11-3
display, front panel, 2-3
display keys, 2-3, 2-7
documentation, 11-13, 11-16
map, D-1
down arrow key, 2-7
drivers, 1-35, 1-37, 11-14
drying time, 3-22–3-23
adjusting, 3-23
color plotting, media type for, 11-2,
11-3
B
color problems, 9-16–9-21
color-vision deficiencies, advice for
users with, 1-20, 3-29
Color/Mono key, 5-10
color/monochrome switching, 5-10
colors
banding problems, 9-20
Bi-Tronics interface, 11-7
black cartridge only, operating with,
1-20
blank plot, 9-10
bleeding lines, 9-19
blurred lines, 9-19
BOOTP, 1-40
CMYK, 5-4
RGB, 5-4
E
electrical specifications, 11-4
electrostatic precautions, 1-8
EMC (electromagnetic compatibility),
11-5, 11-10
communications, problems, 9-9
compensating for poorly cut media,
3-21
components of plotter, xvii–xix
computer, connection to, 1-27–1-30
configuration
changing, 1-30–1-34
current front–panel, 7-3
current overall, 7-2
plot, current, 2-3
setting parameter values, 2-8
connector
parallel, 1-28
serial, 1-28
Copies, 6-8
CorelDRAW!, 5-15, 9-15
Create pattern, 7-6
buttons. See keys
C
cables
ordering, 11-8–11-9
power, 1-5
problems, 9-9
supplied/not supplied, 1-5
calibration. See recalibration
Cancel key, 6-2
cancelling a plot, 6-2
cartridge alignment procedure, 3-30
Cartridge check, 3-26
cartridge stalls, 1-20–1-21, 3-29–3-31
cartridges
Enter key, 2-7
F
file size and memory usage, 6-6
filled area problems, 9-19
film, 11-2, 11-3
firmware, supplied, 1-37
Form Feed and Cut key, 3-25, 6-2,
6-4
to clear the media path, 9-8
front panel, 2-2
action keys, 2-2
before replacing, 3-27
black only, 1-20
colors, 1-5, 1-20–1-21, 3-29–3-31
display section, 2-3
messages, 10-2–10-6
plotting mode keys, 2-2
curl, on media, 9-5
Current Configuration Plot, 5-3, 7-3
I-1
Index
problems with, 9-21–9-22
status lights, 2-2
Front Panel Menus plot, printing, 2-5
Access Cartridge(s), 1-21, 3-28
action, 2-2
Cancel, 6-2
Color/Mono, 5-10
display, 2-3, 2-7
down arrow, 2-7
Enter, 2-7
Form Feed and Cut, 3-25, 6-2, 6-4
Pause, 6-3
plotting mode, 2-2
Previous, 2-7
Print Quality, 5-13
Replot, 6-9
margins (plotting areas), 11-6
maximum media sizes, 11-2
Measure pattern, 7-6
media
adjusting drying time, 3-23
and print quality, 3-6
care of, 3-9
cost and color support, 3-5
curled, 9-5
drying time, 3-22
environmental specifications, 11-4
guidelines for loading, 3-9
handling, 3-9
handling problems, 9-4
important points, 3-2
leading edge, 9-5
loading problems, 9-4
loading roll, 3-10–3-17
loading sheet, 3-18–3-21
physical characteristics, 3-4
poorly cut, 3-21
G
gaps in lines, 9-16, 9-17
gaps in solid fill areas, 9-16
getting help, 9-25
graphics languages, 11-3
and networks, 7-8
changing, 7-7
H
up arrow, 2-7
heavyweight media, 11-2, 11-3
help, 9-25–9-27
HP DesignJets, other, 1-38
HP JetDirect, 1-27
HP JetDirect Print Server, 7-12
HP RTL, 7-7
documentation, 11-13, 11-16
HP Special Inkjet paper, 11-2, 11-3
HP-GL (7586B), 7-7
HP-GL/2, 7-7
L
LAN, 1-27
Lang, 7-7
languages (graphics), 11-3
and networks, 7-8
changing, 7-7
documentation, 11-16
languages (human)
changing, 1-9
manuals available in, 11-13
lever, for media jam, 9-8–9-9
light, effect of, 3-9
Lightness (of plot), adjusting, 5-8
line quality problems, 9-16–9-21
loading media
roll. See roll media
selecting, 3-2–3-7, 3-15–3-16,
3-19–3-20
sheet orientation, 3-18
sizes and plotting areas, 11-6
sizes supported, 11-2
skew tolerance, 3-21
supplies, 11-14
documentation, 11-13, 11-16
humidity, 11-4
I
I/O Setup, 7-9
I/O timeout, changing, 7-9
ink problems, 9-16–9-21
installation. See setting up
interface
parallel specifications, 11-7
problems, 9-9
trimming roll, 3-14
type for application, 3-7
types supported, 3-3, 11-2
unloading, 3-22–3-25
media bin, 3-9
stacking problems, 9-6
Media bypass. See skew tolerance
media jam, 9-8–9-9
Media Reference Guide, 11-14
media types supported, 11-3
memory, xvi, 11-14
expansion modules, 11-14
replot function, 6-9
roll, 3-10–3-17
sheet, 3-18–3-21
Local Area Network, 1-27
logical pens, settings, 5-2–5-5
long–axis plots, 9-12
serial, 9-3
serial specifications, 11-7
specifications, 11-7–11-8
with application software, 9-3
M
Macintosh, cables to connect, 11-8
Maintenance advised, 8-3
managing plots
before printing, 6-4
during printing or drying, 6-2
manuals, 11-13, 11-16, D-1
margins, 4-6, 11-3
J
jagged lines, 9-18
jammed media, 9-8–9-9
memory expansion modules, 1-5
installing, 1-6–1-9
memory usage and file size, 6-6
menu graphics, 2-9
K
and cutting, 4-6
and nesting, 6-13
keys
Menu mode, changing, 1-31
I-2
Index
menu plot, printing, 2-5
menu system
entering, 2-6
navigating, 2-7–2-9
navigation examples, 2-11–2-13
printing, 2-5
roll media, 4-8
sheet media, 4-8
overlapping lines, treatment of, 5-7
overlay of one plot on another, 9-14
clipped, 9-12
content problems, 9-10–9-16
distorted, 9-14
management before printing, 6-4
management during printing, 6-2
position problems, 9-10–9-16
unexpected, 9-15
plot appearance, controlling, 5-2
plot color, quality (DesignJet 750C
Plus), 9-15
P
Merge, 5-7
page
messages, front panel, 10-2–10-6
Microsoft Windows, driver, 11-14
minimum media sizes, 11-2
Mirroring an image, 4-10
monochrome, printing color in, 5-9
Monochrome plotting, media types
for, 11-3
monochrome/color switching, 5-10
Move to top, 6-7
MSDS (Material Safety Data Sheet),
11-10
copying in a queue, 6-8
deleting from a queue, 6-7
identifying in a queue, 6-6
prioritizing in a queue, 6-7
Page format, Rotate. See solving
problems
Page ID, 6-6
page information, 6-7
page margins, 4-6
page size, 4-2–4-5
adjusting, 4-3–4-4
and clipping, 4-5
and nesting, 4-5, 6-13
Palette, 5-4, 5-5, 5-6
palette
changing current selection, 5-6
changing settings, 5-5
palette plot, 5-4, 5-5
paper, clearing jammed. See media
parameter values, setting, 2-8
part numbers, 11-13
Pause key, 6-3
pausing between plots, 6-3
PCs, cables to connect, 11-8
pen, settings, seem to have no effect,
9-14
plotter
components, xvii–xix
views of, xvii–xix
plotting area, 11-6
plotting mode keys, 2-2
polyester film, 11-2, 11-3
ports
on computer, 1-28
on plotter, 1-28
PostScript option, 7-11
power
cord, 1-5, 1-9
socket, 1-9
supply, 1-9
switch, 1-10
power specifications, 11-4
Previous key, 2-7
print cartridges. See cartridges
Print quality, Sharp lines, 5-14
print quality
N
Nest, 6-12
Nest wait, 6-12
nesting
algorithms, 6-12
and margins, 6-13
and page size, 6-13
and Rotate, 6-13
interaction with queue, 6-12
optimizing, 6-13
order, 6-12
overview, 6-10
requirements, 6-11
sets, 6-12
changing, 5-13
choosing, 5-11
Print Quality key, 5-13
print quality problems, 9-16–9-21
print spooler, UNIX, 1-40
problem-solving. See troubleshooting
programming documentation, 11-16
programming languages, 11-3
network
pens, limiting exposure, 3-27
pens (logical)
colors, 5-4
current palette settings, 5-3
settings, 5-2–5-5
pens (physical). See cartridges
physical specifications, 11-3
pin-outs, 11-7–11-10
PJL, 7-8
connections, 1-27
interface, ordering, 11-15
no plot?, 9-23
Normal usage, 8-3
nozzle blockages, 9-16
Q
quality problems, 9-16–9-21
Queue, 6-5
copy page in, 6-8
deleting a page from, 6-7
identifying a page in, 6-6
management, 6-5
O
options
See also accessories
memory, 1-5
ordering accessories, 11-13
orientation
PJL documentation, 11-13
plot
blank, 9-10
cancelling, 6-2
I-3
Index
page information, 6-7
prioritizing a page, 6-7
Service config, 7-5, 8-4
plot, 8-4
support, 9-25–9-27
support services, 11-13
queue, interaction with nesting, 6-12
queueing, 6-5
setting up
checklist, 1-4
T
fast track (quick setup), 1-2
full instructions, 1-4–1-44
items required, 1-5
shading, monochrome, 5-5
shadows of color, 9-18
Sharp lines, 5-14
troubleshooting, 9-15
with CorelDRAW!, 5-15, 9-15
sheet media
loading, 3-18–3-21
orientation, 3-18
sheet sizes supported, 11-2
side-by-side plots. See nesting
signal specifications, 11-7
Size, 4-4
temperature, 11-4
test plot, 1-39
testing the plotter, 9-3
TFTP, 1-40
timeout, overriding, 6-4
translucent, 11-2, 11-3
trimming roll media, 3-14
troubleshooting, 9-1
automatic cutter, 9-5–9-6
lightfastness, 3-9
R
Recalibrate, 7-6
recalibration
for accuracy, 7-5–7-7
restoring factory settings, 7-6
Receiving light, 1-26
regulations
Declaration of Conformity (EC),
11-12
EMC, 11-5
notices, 11-10–11-13
safety, 11-5
regulatory notices, 11-10–11-13
replacing cartridges, 3-26
Replot, 6-9
Restore factory, 7-6
RGB, 5-4
roll media
handling, 3-9
media bin, 9-6
media handling, 9-4
media jam, 9-8–9-9
media loading, 9-4
miscellaneous problems, 9-23–9-25
plot content, 9-10–9-16
plot position, 9-10–9-16
print quality problems, 9-16–9-21
procedure, 9-2–9-3
Rotate, 9-21
size, plotter, 11-3
sizes of media supported, 11-2
skew tolerance, 3-21
slow plotting, 9-23
smears, 9-20
software
setting up, 1-35–1-38
supplied, 1-37
Software Application Notes, 11-13
sound levels, 11-4
special inkjet paper, 11-2, 11-3
specifications, 11-2–11-7
acoustic, 11-4
electromagnetic, 11-5
EMC, 11-5
environmental, 11-4
functional, 11-2
interface, 11-7–11-8
physical, 11-3
loading, 3-10–3-17
stacking problems, 9-6
trimming, 3-14
stacking media in bin, 9-6
U
Rotate
UNIX systems, cables to connect, 11-9
UNIX tips, 1-40
and clipping, 4-8
and nesting, 6-13
interaction with software, 4-9
problems with, 9-21
Rotating a plot, 4-7–4-9
RS-232-C specifications, 11-7
RS–232–C, 7-9
unloading media, 3-22–3-25
unused sheet, removing, 3-25
up arrow key, 2-7
Upgrade, PostScript, 7-11
upgrade, with a network interface, 7-12
RTL documentation, 11-13, 11-16
V
vellum, 11-2, 11-3
S
power, 11-4
safety, 11-5
speed problems, 9-23
Statistics, 6-7, 7-2
status lights, 2-2
safety, MSDS, 11-10
safety specifications, 11-5
Samples, 1-25
selecting media, 3-15–3-16,
3-19–3-20
W
warped lines, 9-18
weights, 11-3
Windows applications, driver, 11-14
workstation, cables to connect, 11-9
storing plots, 3-9
serial interface
Sun, cables to connect, 11-9
supplies. See accessories
Supplies Source Catalog, 11-14
changing settings, 7-9
configuring, 1-29–1-34
I-4
Documentation Map
Printed Documentation for Users of the HP DesignJet 700 plotter and
the HP DesignJet 750C Plus Plotter
Setting Up and Using the Plotter
User’s Guide
(C4705-90031)
(Part of kit
Quick Reference
Guide
(C4705-90041)
(Part of kit
Assembly
Instructions
C4705-60021)
C4705-60021)
Using Application Software
HP CAD Plotters:
Software/Hardware
Guide
Microsoft Windows
Driver for
HP Plotters:
Software
Application Notes
(C4705-90006)
AutoCAD Drivers for
HP Plotters:
(various
Installer’s Guide
documentation)
Getting Support
HP Support
Services
Programmer’s References
HP-GL/2 and RTL
Programmer’s
Reference Guide
(5959-9733)
The Product
PJL Technical
Reference Manual
(5961-0938)
Comparison Guide
for HP-Languages
on HP Plotters and
Large-Format
Printers (5959-9734)
These documents are supplied with this plotter.
These documents can be ordered separately. For details, see page 11-13.
These documents are supplied with this plotter and can be ordered separately.
This manual.
D-1
Notes
D-2
Notes
D-3
Notes
D-4
Notes
D-5
Notes
D-6
If mailing to the address
in the USA (see over), fill
out this sheet.
Please Give Us Your Feedback
on the Quality of This Documentation
If mailing to the address in
Spain, fill out the other
sheet.
Name:
Job Title:
Organization:
Address:
Alternatively, you can fax this
form to:
USA (1) 619 655 6640,
Attn: HP DesignJet Marketing
Dept. or
Spain (34) 3 582 1400,
Attn: Learning Products Dept.
Phone:
Circle the appropriate score
Poor
"
"
"
Excellent
Overall ease of use of this User’s Guide
Overall ease of use of the Quick Reference Guide
Use of language in both documents
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
Use of graphics in both documents
Please explain any low score:
Any other comments on any of the documentation accompanying the plotter:
Thank you
C4705-90031
A
A
A Any comments?
B Fold here and then staple or tape the ends together B
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL
FIRST CLASS MAIL PERMIT NO. 24343 SAN DIEGO, CA
POSTAGE WILL BE PAID BY ADDRESSEE
R
HP DesignJet Marketing Center
Hewlett-Packard Company
Building #7
16399 West Bernardo Drive
San Diego, CA 92127
U.S.A.
If mailing to the address
in Spain (see over), fill out
this sheet.
Please Give Us Your Feedback
on the Quality of This Documentation
If mailing to the address in
the USA, fill out the other
sheet.
Name:
Job Title:
Organization:
Address:
Alternatively, you can fax this
form to:
USA (1) 619 655 6640,
Attn: HP DesignJet Marketing
Dept. or
Spain (34) 3 582 1400,
Attn: Learning Products Dept.
Phone:
Circle the appropriate score
Poor
"
"
"
Excellent
Overall ease of use of this User’s Guide
Overall ease of use of the Quick Reference Guide
Use of language in both documents
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
Use of graphics in both documents
Please explain any low score:
Any other comments on any of the documentation accompanying the plotter:
Thank you
C4705-90031
A
A
A Any comments?
B Fold here and then staple or tape the ends together B
R
Hewlett-Packard Company
Barcelona Division
Attn: Learning Products Dept.
Avda. Graells, 501
08190 Sant Cugat del Vallès
Spain
R
Customer re-order number: C4705-60021
Manual Part Number: C4705-90031
Edition 1, September 1996
English
Printed in U.S.A.
This manual has been printed on chlorine-free bleached paper
R
Customer re-order number: C4705-60021
Manual Part Number: C4705-90031
Edition 1, September 1996
English
Printed in Europe
This manual has been printed on chlorine-free bleached paper
|