HP 2512 User Manual

Revision 1.3ꢀ

July 2001ꢀ

Contents

INTRODUCTION ...............................................................................................................................................1ꢀ

1.1 CONVENTIONS ...................................................................................................................................................1ꢀ

1.2 ARGUMENT TYPES.............................................................................................................................................1ꢀ

1.3 PRIVILEGE AND CONTEXT LEVELS.....................................................................................................................2ꢀ

1.4 THE COMMAND LINE INTERFACE......................................................................................................................3ꢀ

1.5 SYSTEM HELP ....................................................................................................................................................3ꢀ

1.6 COMMAND LINE EDITING..................................................................................................................................4ꢀ

COMMAND SUMMARY...................................................................................................................................5ꢀ

2.1 USER EXEC COMMANDS ..................................................................................................................................5ꢀ

2.2 DIAGNOSTIC COMMANDS ..................................................................................................................................6ꢀ

2.3 SYSTEM CONFIGURATION................................................................................................................................11ꢀ

2.3.1

2.3.2

System commands - EXEC level............................................................................................................11ꢀ

System Configuration commands..........................................................................................................14ꢀ

2.4 AUTHENTICATION .....................................................................................................................................16ꢀ

2.4.1 AUTHENTICATION commands - Configuration level.........................................................................16ꢀ

2.5 TACACS.........................................................................................................................................................17ꢀ

2.5.1

2.5.2

TACACS commands - EXEC level ........................................................................................................17ꢀ

TACACS commands - Configuration level ...........................................................................................17ꢀ

2.6 CDP.................................................................................................................................................................17ꢀ

2.6.1

2.6.2

CDP commands - EXEC level...............................................................................................................17ꢀ

CDP commands - Configuration level..................................................................................................17ꢀ

2.7 IP STACKING ...................................................................................................................................................18ꢀ

2.7.1

2.7.2

IP Stacking commands - EXEC level ....................................................................................................18ꢀ

IP Stacking commands - Configuration level .......................................................................................18ꢀ

2.8 PORT SETTINGS ...............................................................................................................................................20ꢀ

2.8.1

2.8.2

Port commands - EXEC level................................................................................................................20ꢀ

Ethernet Interface Configuration Commands.......................................................................................22ꢀ

2.9 TRUNK CONFIGURATION .................................................................................................................................23ꢀ

2.9.1

2.9.2

2.10

Trunk commands - EXEC level .............................................................................................................23ꢀ

Trunk commands - Configuration level ................................................................................................24ꢀ

SPANNING TREE..........................................................................................................................................25ꢀ

2.10.1 Spanning Tree commands - EXEC level ...............................................................................................25ꢀ

2.10.2 Spanning Tree commands - Configuration level ..................................................................................26ꢀ

2.11

IP ................................................................................................................................................................28ꢀ

2.11.1 IP commands - EXEC level...................................................................................................................28ꢀ

2.11.2 IP commands - Configuration level ......................................................................................................31ꢀ

2.11.3 IP commands - VLAN Interface level....................................................................................................33ꢀ

2.12

SNMP.........................................................................................................................................................34ꢀ

2.12.1 SNMP commands - EXEC level ............................................................................................................34ꢀ

2.12.2 SNMP commands – Configuration Level..............................................................................................35ꢀ

2.13

VLAN CONFIGURATION.............................................................................................................................36ꢀ

2.13.1 VLAN commands - EXEC level.............................................................................................................36ꢀ

2.13.2 VLAN commands – Configuration Level ..............................................................................................36ꢀ

2.13.3 VLAN Interface commands ...................................................................................................................37ꢀ

2.14

GVRP.........................................................................................................................................................38ꢀ

2.14.1 GVRP commands - EXEC level.............................................................................................................38ꢀ

2.14.2 GVRP commands – Configuration level...............................................................................................38ꢀ

2.14.3 Ethernet Interface Configuration commands........................................................................................38ꢀ

2.15

IGMP..........................................................................................................................................................39ꢀ

2.15.1 IGMP Commands – EXEC Level.........................................................................................................39ꢀ

2.15.2 IGMP Configuration commands – Vlan Interface level .......................................................................40ꢀ

2.16

PORT MONITORING.....................................................................................................................................41ꢀ

2.16.1 Port Monitoring commands - EXEC level ............................................................................................41ꢀ

2.16.2 Port Monitoring commands - Configuration level................................................................................41ꢀ

2.16.3 Port Monitoring commands - VLAN Interface level............................................................................42ꢀ

2.16.4 Port Monitoring commands - Ethernet Interface level........................................................................42ꢀ

2.17

PORT SECURITY ..........................................................................................................................................42ꢀ

2.17.1 Port Security commands - EXEC level .................................................................................................42ꢀ

2.17.2 Port Security commands - Configuration level.....................................................................................43ꢀ

CONSOLE MENU.............................................................................................................................................45ꢀ

3.1 STATUS AND COUNTERS..................................................................................................................................45ꢀ

3.1.1

3.1.2

3.1.3

3.1.4

3.1.5

General System Information .................................................................................................................46ꢀ

Management Address Information........................................................................................................46ꢀ

Module Information ..............................................................................................................................47ꢀ

Port Status.............................................................................................................................................47ꢀ

Port Counters........................................................................................................................................48ꢀ

3.1.5.1 Port Counters Details.........................................................................................................................................48ꢀ

3.1.6

Address Table........................................................................................................................................49ꢀ

Port Address Table................................................................................................................................49ꢀ

Spanning Tree Information ...................................................................................................................50ꢀ

3.1.7

3.1.8

3.1.8.1 Spanning Tree Port Information........................................................................................................................50ꢀ

3.2 CONFIGURATION MENU...................................................................................................................................51ꢀ

3.2.1

3.2.2

3.2.3

3.2.4

3.2.5

3.2.6

3.2.7

3.2.8

System Information................................................................................................................................52ꢀ

Port/Trunk Settings ...............................................................................................................................52ꢀ

Network Monitoring Port......................................................................................................................53ꢀ

Spanning Tree Operation......................................................................................................................53ꢀ

IP Configuration ...................................................................................................................................54ꢀ

SNMP Communities ..............................................................................................................................55ꢀ

Authorized Managers............................................................................................................................55ꢀ

VLAN Menu...........................................................................................................................................56ꢀ

3.2.8.1 VLAN Support ..................................................................................................................................................56ꢀ

3.2.8.2 VLAN Names....................................................................................................................................................57ꢀ

3.2.8.3 VLAN Port Assignment....................................................................................................................................57ꢀ

3.3 PASSWORD MENU............................................................................................................................................58ꢀ

3.4 EVENT LOG......................................................................................................................................................58ꢀ

3.5 DOWNLOAD SCREEN .......................................................................................................................................59ꢀ

3.6 RUN SETUP ......................................................................................................................................................59ꢀ

Introduction

This document provides a summary of the commands supported on the HP ProCurve 2524,

2512, and 4108gl switches. It is divided into sections that correspond to different modules or

features of the HP switches. Not all sections will apply to all HP switches since each switch

may only support a subset of the total feature set that is described in this document.

1.1 Conventions

Command descriptions use the following conventions:

ꢀ Vertical bars “|” separate alternative, mutually exclusive elements.

ꢀ Square brackets “[ ]” indicate optional elements.

ꢀ Braces “<>” indicate a required choice.

ꢀ Braces within square brackets “[<>]” indicate a required choice within an optional

element.

ꢀ Boldface indicates commands and keywords that are entered literally as shown.

ꢀ Italics indicates arguments for which you must supply a value.

ꢀ If the no form of a command has exactly the same keywords and arguments as the

command, then no appears in square brackets at the beginning of the command.

Otherwise, the no form of the command is described separately.

ꢀ If the no form of a command is not explicitly described, then it simply negates the

command. For example, if the command enables a feature, then the no form of the

command would disable it. Also, if the a command was used to add a configuration item,

then the no form of the command would remove it.

1.2 Argument Types

The following argument types are recognized by the CLI and are used in the command

syntax throughout this document:

ꢀ mac-addr – For example, 0060b0-885a80 or 0060b0:885a80.

ꢀ ip-addr - IP address in dotted decimal notation. For example, 10.0.16.80

ꢀ ip-mask - This is syntactically expressed the same way as ip-addr.

ꢀ port-number - Devices with fixed port configurations accept port numbers

specified as integers. Modular devices accept port numbers specified with slot

and port number identifiers. For instance, port "A1" indicates Port 1 in Slot A.

1ꢀ

There are three "special" port designations in the switch. You may specify the

monitoring port by using "mp"; you may specify a trunk port by using "trkX",

where X identifies the numerical trunk group.

ꢀ port-list - A port list specifies a group of ports for which the operation being

performed should be applied. A port list consists of individual port identifiers or

ranges of ports separated by commas (e.g., A1-B8, C4, D1). This list includes the

"special" port designations described under port-number.

ꢀ vlan-id - The 802.1Q VLAN identifier.

1.3 Privilege and Context levels

The new CLI will support two privilege levels (operator and manager) and several context

levels. As each context level is entered, the context information is displayed as part of the

command prompt. When a context specific command is executed, the context information

is applied to the particular command. For instance, when you attempt to enter the interface

context level, you must specify a port number (see interface ethernet). Subsequent

commands that affect port behavior (e.g., flow-control) will be applied to the port number

specified when entering the level, so the specified port need not be re-specified on the

command line.

EXEC level

HP 4108GL>

Global configuration level

HP 4108GL(config)

interface config level

HP 4108GL(if-A1)

vlan config level

HP 4108GL(vlan-1)

Figure 1: Command and context levels

When you log onto the switch, you will be placed at the operator EXEC level and the

system will display the following prompt:

HP 4108GL>ꢀ

2ꢀ

If an operator password has been set (see password in the global configuration section),

then the system would have displayed the following prompt before entering the operator

EXEC level:

Password:ꢀ

You can enter the manager EXEC level from the operator EXEC level by using the enable

command. If a manager level password has been configured, then you will be prompted for

the manager password after executing the enable command.

1.4 The Command Line Interface

The new CLI will not be case sensitive. As a short cut, you can abbreviate commands and

keywords as long they contain enough letters to be distinguished from any other currently

available commands or keywords.

When the command text exceeds the length of the command line, the current command line

will scroll upwards, yet the cursor will shift to the first character on the last line on the

screen. This is opposed to shifting the command line horizontally each time the command

exceeds the number of characters that can be displayed at one time on the screen.

1.5 System Help

You can enter help or ? at a particular command level to see the commands available at that

level. You can enter a command followed by help or ? in order to get the system to display

the command description for that particular command. The command description would be

similar to what is presented for each command in the Command Reference section of this

document.

In order to see the list of possible word completions or to complete the current word, you

may use the Tab key immediately after the last letter of the last keyword on the command

line. For example, if the system was currently in the global configuration level and you typed

tab immediately after the t in step (1), the system would display the options seen in section

(2) and the system would return to the configuration level prompt with the partially

completed command line seen in (3):

(1) HP 4108GL(config) tꢀ

(2) trunkꢀ

trapꢀ

trap-send-authenticationꢀ

telnet-serverꢀ

(3) HP 4108GL(config)tꢀ

3ꢀ

If you had already typed in trap- on line (1) and then pressed the tab character, the system

would complete the keyword trap-send-authentication, for it is the only possible

completion for trap-, and display the completed command line as shown below:

1. HP 4108GL(config) trap-

2. HP 4108GL(config) trap-send-authentication

1.6 Command Line Editing

Before you press return, the current command line can be edited using special keys

including arrows and control characters. The following table describes the supported

command editing keys and their function:

Keystroke

Function

Jumps to the first character of the command line.

Moves the cursor back one character.

Ctrl-A

Ctrl-B; left arrow

Ctrl-C

Escapes and terminates prompts and lengthy tasks.

Deletes the character at the cursor.

Ctrl-D

Ctrl-E

Jumps to the end of the current command line.

Moves the cursor forward one character.

Deletes from the cursor to the end of the command line.

Repeats current command line on a new line.

Enters next command line in the history buffer.

Enters previous command line in the history buffer.

Deletes from the cursor to the beginning of the command line.

Deletes last word typed.

Ctrl-F; right arrow

Ctrl-K

Ctrl-L; Ctrl-R

Ctrl-N; down arrow

Ctrl-P; up arrow

Ctrl-U; Ctrl-X

Ctrl-W

Esc B

Moves the cursor backward one word.

Esc D

Deletes from the cursor to the end of the word.

Moves the cursor forward one word.

Esc F

Erases mistake when entering a command; reenter command after using this

key.

Delete; Backspace

4ꢀ

Command Summary

2.1 User EXEC Commands

enable

Enters the manager EXEC level. If a manager password is set, the system will first

prompt for the password. Echoing is disabled while you enter the password. Initially

there are no passwords for the two levels of users in the system: manager and

operator. When you first connect to the console or telnet into the system, you will be

placed into the Operator EXEC level. At that time, you can enter the above enable

command without a password in order to be granted manager access to the switch

and to be placed into the manager EXEC level. Passwords are set and changed

through the password command at the global configuration level.

configure [terminal]

Used to enter the global configuration level.

end

This command sets the current command or context level to the manager EXEC

level.

exit

This command sets the current command level to the previous command level. At

the operator EXEC level, this command acts the same as logout.

interface [ethernet] <port-list>

Enters the Ethernet interface configuration context for the port-list.

logout

Terminates this console/telnet session.

Used to enter the menu system. For more information, see the Console Menu

section of this document.

setup

Used to setup initial switch configuration.

5ꢀ

[no] page

Toggles the paging mode for display commands so that the “—more –“ will appear

or not appear.

repeat

Repeatedly executes the previous command until a key is pressed.

vlan <vlan-name | vlan-id>

Enters the VLAN interface configuration context for the VLAN.

2.2 Diagnostic Commands

boot [system [flash <primary|secondary>]]

Performs cold reboot of switch.

write terminal

This command displays the running configuration.

write memory

This command saves the running configuration to Flash.

erase startup-config

Deletes the configuration stored in flash so that the switch will reverted to it’s

default configuration upon reboot.

erase flash <primary|secondary>

Deletes the configuration stored in flash so that the switch will reverted to it’s

default configuration upon reboot.

copy tftp <startup-config|flash> <ip-addr> <remote-file>

[primary|secondary]

Retrieves a configuration or OS file on the remote host, and overwrites the switch's

corresponding file with the remote file.

6ꢀ

tftp <ip-addr> <remote-file>

This command writes the switch's configuration file, crashrec, eventlog or the output

from a command specified by Command to the remote file on the remote host.

show startup-config

Displays the configuration stored in flash.

show running-config

Displays the configuration stored in flash.

show boot-history

Displays the switch shutdown history.

kill

This command kills all other active sessions.

show logging [-a] [<search-text>]

Displays the switch's event log. If -a is specified then entire internal switch log is

displayed. If search-text is specified then only events that contain that text are

displayed.

print <command>

Used to execute a command and captures its output using a terminal emulator. This

command will display “Press RETURN when ready…” to allow the terminal

emulator to be set up to for the capture and “Press RETURN when done…” once

the output is complete.

show history

Displays the current command history.

reload

Performs a warm reboot.

clear arp

To clear the arp cache of all non-permanent entries.

7ꢀ

clear intrusion-log

To clear the intrusion log.

clear statistics [ethernet] <port-list>

To reset counters displayed by the console. If a new console session is initiated, the

counters will revert back to the values maintained by the switch hardware.

telnet <ip-addr>

To initiate a telnet session with another network device.

telnet <0..15>

To initiate a telnet session to a member switch in the stack.

Parameters:ꢀ

ꢀ <0..15> specifies the number of the switch to be contacted.ꢀ

getmib <object-name> [<object-name> …]

Retrieves and displays the MIB object defined by object-name.

walkmib <object-name>

This command shows a group of managed object values.

8ꢀ

setmib <object-name> <type> <value> [<object-name> <type> <value> …]

This command sets the MIB object defined by object-name. The options for the type

parameter are case sensitive as shown below:

-i

Integer

-o

-d

-a

Octet string

Object identifier

IP address (nnn.nnn.nnn.nnn)

Counter

-c

-g

-t

Gauge

Time tick

-u

-D

-N

Unsigned integer

Display string (“value”)

Null

show version

Displays software version information.

show flash

Displays software version information for images in flash.

show tech

Displays switch information needed by HP support for diagnostics.

copy xmodem < startup-config |flash [primary|secondary]>

Retrieves a configuration file using the Xmodem protocol and then writes the

retrieved file to the switch's flash.

xmodem [ pc | unix ]

Writes either the configuration file, crashrec, eventlog, or the output from a

command specified by command using the Xmodem protocol.

9ꢀ

link-test <mac-addr> [vlan <vlan-id>] [repetitions <1..999>] [timeout <1..256>]

Tests the connection to a MAC station on the LAN by sending a 802.2 test packet to

a specific target node on a network directly attached to a port in that LAN. The

target node must be able to respond to this test packet with an 802.2 Test Response

packet in order for the test to work. The switch produces the following output if the

link test succeeds:

link-test passedꢀ

otherwise, the following is displayed:

link-test failedꢀ

Parameters:

ꢀ <mac-addr> - MAC address of the station to send link test to.

ꢀ vlan <vlan-id> - Expected VLAN on which the station is expected to be present.

If this argument is not present then the VLAN used is 1.

ꢀ repetitions <1..9999> - Number of test packets to send; the default value is 1.

ꢀ timeout <1..256> - Seconds within which a response is required before the test

is considered as failed; the default value is 5.

ping <ip-addr> [repetitions <1..999>] [timeout <1..256>]

Issues an IP Ping requests to an IP device on the network and the system displays

the following output at the CLI if a response is received from the specified IP

address:

192.32.36.75 is alive, time = 10 msꢀ

If no response is received the system displays the following:

Target did not respondꢀ

Parameters:

ꢀ <ip-addr> - Network IP address of station to send IP Ping to.

ꢀ repetitions <1..999>- Number of times to send IP Ping; the default value is 1.

ꢀ timeout <1..256> - Seconds within which a response is required before the test

is considered as failed; the default value is 5.

10ꢀ

2.3 System Configuration

2.3.1 System commands - EXEC level

show console

Displays the console parameters.

Output Format:

Switch Configuration - Console/Serial Linkꢀ

Inbound Telnet Enabled [Yes] : Yesꢀ

Web Agent Enabled [Yes] : Yesꢀ

Terminal Type [VT100] : VT100ꢀ

Screen Refresh Interval (sec) [3] : 3ꢀ

Displayed Events [All] : Allꢀ

Baud Rate [Speed Sense] : Speed Senseꢀ

Flow Control [XON/XOFF] : XON/XOFFꢀ

Connection Inactivity Time (min) [0] : 0ꢀ

show mac-address [vlan <vlan-id>]

Displays the MAC addresses that the switch has learned from the network devices

attached to the switch, and the port on which each address was learned. If no vlan is

specified, then all MAC addresses that are know to the switch are shown.

Output Format:

Status and Counters - Address Tableꢀ

MAC Address Located on Portꢀ

-------------ꢀ ---------------

00105a-8abed4 1ꢀ

00105a-cac0e8 1ꢀ

0060b0-881c00 1ꢀ

009004-8e3178 1ꢀ

00c0f0-1c65ee 1ꢀ

00c0f0-30d74a 1ꢀ

080009-3515f9 1ꢀ

080009-782368 1ꢀ

080009-7b8cc4 1ꢀ

080009-919b30 1ꢀ

080009-959e2c 1ꢀ

11ꢀ

show mac-address <port-list>

Displays the MAC addresses that the switch has learned from the network devices

attached to the specified switch port.

Output Format:

Status and Counters - Port Address Table - Port 1ꢀ

MAC Addressꢀ

-------------ꢀ

00105a-8abed4ꢀ

00105a-cac0e8ꢀ

009004-8e3178ꢀ

00c0f0-1c65eeꢀ

00c0f0-1c66eaꢀ

00c0f0-30d74aꢀ

080009-3515f9ꢀ

080009-782368ꢀ

080009-7b8cc4ꢀ

080009-919b30ꢀ

080009-959e2cꢀ

show management

Displays configured addresses that are used to manage the switch.

Output Format:

Status and Counters - Management Address Informationꢀ

Time Server Address :ꢀ

MAC Address

IP Address

: 0060b0-885a80ꢀ

: 192.32.36.96ꢀ

IPX Network Number :ꢀ

12ꢀ

show modules

Displays the modules that are present on the switch.

Output Format:

Status and Counters - Module Informationꢀ

Module Type Module Descriptionꢀ

Slot

----ꢀ --------------- --------------------------------------------

Slot Availableꢀ

show system-information

Displays the status of and current configuration of all the switch internal resources.

Output Format:

System Informationꢀ

..System Name

System Contact

System Location

:ꢀ

Address Age Interval (min) [5] : 5ꢀ

Time Zone [0] : 0ꢀ

Daylight Time Rule [None] : User definedꢀ

Beginning month [April] : April ꢀ

Beginning day [1] : 1ꢀ

Ending month [October] : October ꢀ

Ending day [1]

: 1ꢀ

Firmware revision : C.08.XX ꢀ

Base MAC Addr

Serial Number

: 0060b0-885a80ꢀ

: +ꢀ

ROM Version

: C.05.X1 ꢀ

Up Time

: 17 hours ꢀ

Memory - Total : 7,669,088ꢀ

CPU Util (%)

: 2 ꢀ

Free : 4,871,840ꢀ

IP Mgmt - Pkts Rx : 14,496 ꢀ

Packet - Total : 462ꢀ

Buffers ꢀ Free : 296ꢀ

Lowest : 237ꢀ

Pkts Tx : 9463 ꢀ

Missed : 0ꢀ

13ꢀ

2.3.2 System Configuration commands

mac-age-time <1..100000>

Sets the number of seconds a MAC address stays in the switch address table before

being aged out. Aging out occurs if traffic isn't received from that MAC station

within the age interval. The default value is 300.

console [terminal <vt100 | ansi> [screen-refresh <value>] [events <none | all | non-

info | critical | debug>] [baud-rate <value>] [flow-control <xon/xoff | none>]

[inactivity <value>]

Sets the console parameters.

Parameters:

ꢀ terminal <vt100 | ansi> - Type of terminal being used (default is vt100).

ꢀ screen-refresh <1|3|5|10|20|30|45|60> - Sets the number of seconds before a

refresh is done on the “Status and Counters” screens (default is 3).

ꢀ events <none | all | non-info | critical | debug>] – The level of Switch events

displayed in Events Log. all - display all; none - display no events; not-info - display

all events except informational-only; critical - display only critical-level events;

debug (reserved for Internal use only).

ꢀ baud-rate <speed-sense | 1200 | 2400 | 4800 | 9600 | 19200 | 38400 | 57600

| 115200>] - Sets the data transmission speed for switch connect sessions initiated

through the Console port. Default is speed-sense.

ꢀ flow-control <xon/xoff | none> - Flow Control Method; default is xon-xoff.

ꢀ inactivity-timer <0 | 1 | 5 | 10 | 15 | 20 | 30 | 60 | 120> - Sets the number of

minutes of inactivity allowed by the switch before the switch will terminate the

communication session. 0 means never terminate the session; default is 0 .

[no] auto-tftp <ip-addr filename>

Enables/disables automatic OS image download via TFTP.

14ꢀ

time [mm/dd/yy] [hh:mm:ss] [timezone <value>] [daylight-time-rule <value>] [begin-date

<mm/dd> end-date <mm/dd>]

This command display switch's date & time or optionally sets it.

Parameters:

ꢀ timezone <-1440..1440> - Sets the number of minutes your location is to the

West(+) or East(-) of GMT (default is 0).

ꢀ daylight-time-rule <alaska | none | continental-us-canada | middle-europe-

and-portugal | southern-hemisphere | western-europe | user-defined> -

Sets the daylight savings time rule for your location. None (default) means that no

time adjustment will be made.

ꢀ begin-date <mm/dd> end-date <mm/dd > - begin-date and end-date are only

valid if the daylight time rule is set to user-defined.

snmp-server [contact <sys-contact>] [location sys-location>]

Sets the switch contact and location for administrative purposes.

Parameters:

ꢀ contact <sys-contact> - Up to 48 characters. Name of the switch administrator.

ꢀ location <sys-location> - Up to 48 characters. Description of the switch location.

hostname <name-string>

Sets the switch name for administrative purposes.

15ꢀ

[no] telnet-server

Enables remote telnet access to the switch.

[no] web-management

Enables the web browser to interact with the web agent on the switch.

[no] password <operator | manager>

Sets passwords for different classes of users. This command causes the switch to

prompt for a password twice, once for the new password and once to verify it was

typed correctly, and disables echoing while you type the password.

Parameters:

ꢀ <operator | manager> - Class of user.

2.4 AUTHENTICATION

2.4.1 AUTHENTICATION commands - Configuration level

aaa authentication console <enable|login>

<primary-method> [<backup-method>]

Configures authentication mechanism used to control access to the switch.

aaa authentication telnet <enable|login>

<primary-method> [<backup-method>]

Configures authentication mechanism used to control access to the switch.

16ꢀ

2.5 TACACSꢀ

2.5.1 TACACS commands - EXEC levelꢀ

show tacacsꢀ

Displays TACACS configuration.

2.5.2 TACACS commands - Configuration level

[no] tacacs-server host <ip-addr> [key <key-string>]

Configures a TACACS server.

tacacs-server timeout <1-255>

Sets up the TACACS timeout interval in seconds.

2.6 CDP

2.6.1 CDP commands - EXEC level

show cdp [neighbor [port-num] [detail]]

Displays CDP configuration and neigbors discovered.

2.6.2 CDP commands - Configuration level

[no] cdp

Enables/disables CDP on the switch.

cdp timer <5-254>

Sets the CDP transimit interval in seconds.

cdp holdtime <10-255>

Sets the CDP holdtime in seconds.

cdp enable [ethernet] <port-list>

Enables/disables CDP on a particular port.

17ꢀ

2.7 IP Stacking

2.7.1 IP Stacking commands - EXEC level

show stack [candidates | all]

Displays status information for the stacking feature. ‘show stack’ with no arguments

displays the status of this switch’s stack. If the keyword candidates is supplied then

this command displays a list of candidates on the local network segment. If the

keyword all is supplied then this command displays all the member switches of all

stacks on the local network segment and all candidate switches.

2.7.2 IP Stacking commands - Configuration level

[no] stack

Enables/disables the stacking feature. If the stacking features is disabled, then the

switch will reject a join request originating from a command switch.

[no] stack commander <commander-name>

Creates a command switch, and the no form of the command disperses the member

switches from this command switch’s stack, making them available to join another

stack.

[no] stack member <switch-num> mac-address <mac-addr> [password <password-str>]

Configures the candidate switch identified by the MAC address to be a member for

this switch’s stack. The no form of the command removes the switch identified by

switch-num from the stack

Parameters:

ꢀ <switch-num> - A number between 1 and 15 to uniquely identify each switch; a

switch-num of zero always belongs to the command switch.

ꢀ password <password-str> - is the manager password configured on the candidate

switch. If the candidate switch does not have a manager password then none

should be supplied.

[no] stack join <mac-addr>

Causes a candidate switch to join the stack whose command switch is identified by

mac-addr. The no form of the command causes the member switch to leave its

current stack.

18ꢀ

[no] stack auto-join

Causes the switch to advertise, via the discovery protocol, that it wants to

automatically join any stack operating on the local LAN segment. Switches with

passwords will not auto-join.

[no] stack auto-grab

Enables/disables auto-grab mode for stacking on the command switch. If enabled,

the command switch will attempt to grab new candidate switches and make them

members of the stack.

stack transmission-interval <n>

Sets the transmission interval for stacking.

19ꢀ

2.8 Port Settingsꢀ

2.8.1 Port commands - EXEC levelꢀ

show interfaces configꢀ

Displays the basic configuration of the switch ports.

Output Format:

Switch Configuration - Port Settingsꢀ

Port ꢀ Type

Enabled

Mode

Flow Ctrl Bcast Limit

----ꢀ -------- + ------- ------------ --------- -----------

1 ꢀ

2 ꢀ

3 ꢀ

4 ꢀ

5 ꢀ

6 ꢀ

7 ꢀ

8 ꢀ

9 ꢀ

10/100TX | Yes

Auto

Disable

10 ꢀ 10/100TX | Yes

11 ꢀ 10/100TX | Yes

show statistics

Displays a summary of the network traffic handled by the switch.

Output Format:

Status and Counters - Port Countersꢀ

Port Total Bytes Total Frames

Errors Rx

Drops Tx

---- ------------- ------------- ------------- -------------

83,612,741

446,524

15,080

20ꢀ

show statistics <port-number>

Displays the network traffic statistics for the specified port.

Output Format:

Status and Counters - Port Counters - Port 1ꢀ

Link Status

: Upꢀ

Bytes Rx

Unicast Rx

: 83,290,873

: 395,490

Bytes Tx

Unicast Tx

: 1,234,430ꢀ

: 14,995ꢀ

Bcast/Mcast Rx : 40,161

Bcast/Mcast Tx : 180ꢀ

FCS Rx

: 3

: 1

: 0

Drops Tx : 0ꢀ

Alignment Rx

Runts Rx

Giants Rx

Collisions Tx : 25ꢀ

Late Colln Tx : 0ꢀ

Excessive Colln : 0ꢀ

Total Rx Errors : 4

Deferred Tx

: 17ꢀ

21ꢀ

show interfaces

Displays the status and current configuration of all the switch ports.

Output Format:

Status and Counters - Port Statusꢀ

Intrusion

Alert

Flow

Ctrl

Bcastꢀ

Limitꢀ

Port

Type

Enabled Status

Mode

----ꢀ -------- --------- ------- ------ ---------- --------- ------

10/100TX No

Yes

0ꢀ

Down

2.8.2 Ethernet Interface Configuration Commands

To enter the Ethernet Interface Configuration level, use the Interface command described

above. Note that a port-list may be used to configure these options on more than one port

and that any of the following commands can be appended to the Interface command to

simply change the configuration. For example:

HP 4108GL(config)# interface ethernet A1,A3 disableꢀ

broadcast-limit <0..99>

Sets the theoretical maximum of network bandwidth in percentage that can be used

for broadcast traffic. Any broadcast traffic exceeding that limit will dropped. 0 means

the feature is disabled.

disable

Disables the port.

enable

Enables the port.

22ꢀ

[no] flow-control

Enables or disables flow control on the port.

Note: Full-duplex ports only.

Sets the mode of operation for the port.

[no] lacp [active|passive]

enables or disables LACP on the port.

2.9 Trunk Configuration

2.9.1 Trunk commands - EXEC level

show trunks [<port-list>]

Displays trunks that are configured on the system. This does not include dynamic

trunks that have been formed by LACP.

Output Format:

Switch Configuration - Trunksꢀ

Port ꢀ Type

Group

Type

| Port

Type

Group

Typeꢀ

----ꢀ -------- + ----- -------- | ---- -------- + ----- --------

10/100TX |

| 9

10/100TX |

10/100TX | Trk1 FEC

10/100TX |

10/100TX | Trk2 Trunk

10/100TX |

| 10

| 11

| 12

| 13

| 14

| 15

| 16

10/100TX |

23ꢀ

show lacp

Displays LACP status information.

Output Format:

LACPꢀ

P0RT LACP

TRUNK

PORT

LACP

LACPꢀ

NUMB ENABLED GROUP

STATUS PARTNER

STATUSꢀ

----ꢀ -------- ----- -------- --------- ---------

Active

Passive

Active

Dyn1 Up

Trk1 Down

Blocked No

Disabledꢀ

Dyn1 Up

Yes

Successꢀ

Failureꢀ

Yes

Successꢀ

Standbyꢀ

Upꢀ

2.9.2 Trunk commands - Configuration level

[no] trunk <trk1..trk24 > [trunk | fec | lacp] <port list>

This command configures each port in the switch to either be a Trunked, SA Only

Trunked, FEC Trunked port, or a regular singular port.

For Trunks: All ports in a Trunked group, 1 to 4 ports maximum, must have the same

port type.

General Considerations: (1) To avoid broadcast storms, or loops in your network

while configuring trunks, first disable or disconnect all the ports you wish to add or

remove from both sides of the trunk. Once done configuring the trunk, enable or re-

connect the ports. (2) If you have multiple groups of the same or different types and/or

singular connections between two switches, you have created a loop in the network. You

must enable Spanning Tree on both switches to avoid a broadcast storm or other

network problems. See the Switch Management and Configuration Guide for more

information.

Parameters:

ꢀ <trk1..trk24 |none> - Determines the group that a port is configured to be a

member of: trkX indicates a general group of trunked ports; none indicates that the

associated port is a singular independent port (i.e., not part of a trunk).

24ꢀ

ꢀ [type <trunk | fec | lacp>] - Determines the method by which the switch

distributes the traffic load across the multiple links in the trunk group: trunk - uses

source and destination MAC addresses for load distribution (select this to connect to

devices such as the HP Switch 2000 or the Sun Trunk Server); fec - uses an

automatic protocol for load distribution (select this to connect to devices that

support Cisco's Fast EtherChannel trunking).

2.10 Spanning Treeꢀ

2.10.1 Spanning Tree commands - EXEC levelꢀ

show spanning-tree configꢀ

Displays spanning tree configuration information.

Output Format:

Switch Configuration - Spanning Tree Operationꢀ

Spanning Tree Enabled [No] : Noꢀ

STP Priority [32768] : 32768

Hello Time [2] : 2ꢀ

Max Age [20] : 20 ꢀ

Forward Delay [15] : 15ꢀ

Port ꢀ Type

Cost Pri Mode | Port

Type

Cost Pri Mode

----ꢀ -------- + ----- --- ---- | ---- -------- + ----- --- ----

10/100TX | 10

128 Norm | 9

128 Norm | 10

128 Norm | 11

128 Norm | 12

128 Norm | 13

128 Norm | 14

128 Norm | 15

10/100TX | 10

128 Norm

25ꢀ

show spanning-tree

Displays bridge-level spanning tree information.

Output Format:

Status and Counters - Spanning Tree Informationꢀ

STP Enabled

Switch Priority

Hello Time

Max Age

: Yesꢀ

: 32,768ꢀ

: 2ꢀ

: 20ꢀ

Forward Delay

: 15ꢀ

Topology Change Count : 1ꢀ

Time Since Last Change : 4 minsꢀ

Root MAC Address

Root Path Cost

Root Port

: 0060b0-885a80ꢀ

: 0ꢀ

: This switch is rootꢀ

Root Priority

: 32768ꢀ

Port

Type

Cost Priority

State

Designated Bridgeꢀ

----ꢀ -------- ----- -------- ---------- -----------------

10/100TX

128 Forwarding 0060b0-885a80ꢀ

128 Disabledꢀ

2.10.2 Spanning Tree commands - Configuration level

[no] spanning-tree

Enables or disables spanning tree on the device.

26ꢀ

spanning-tree [forward-delay <seconds>]

[hello-time <seconds>]

[maximum-age <seconds>]

[priority <0..65535>]

spanning-tree <[ethernet] port-list> [path-cost <1..65535>]

[priority <0..255>]

[mode <norm|fast>]

This command configures the parameters for operation of the switch in a spanning

tree topology. Note - the default spanning tree configuration complies with the

IEEE 802.1D standard recommended values and should not be changed without

thorough knowledge of spanning tree operation. Note: As per IEEE 802.1Q

Standard, this switch implements a single instance of Spanning Tree operating over

all VLANs.

Parameters:

ꢀ path-cost <port-list><1..65535> - Individual port cost used to determine which

ports are forwarding ports. The defaults is 100 for 10 Mbps ports, 10 for

10/100TX and 100FX ports, and 5 for 100/1000TX and 1Gbps ports.

ꢀ priority <port-list><0..255> - Another value used by spanning tree to the

forwarding ports. The port with the lowest number has the highest priority. The

default is 128.

ꢀ mode <port-list> [norm | fast] (default: norm) - norm (for normal) mode causes

the port to operate according to the standard Spanning Tree Protocol - when

connected, the port progresses through the Listening, Learning, and either

Blocking or Forwarding states. fast mode causes the port to immediately

operate in the Forwarding State when a device is connected to it. Use this setting

only on ports that are connected to end nodes (for example: PCs, Workstation,

or printers). Caution: Changing the Mode to fast on ports connected to a hub or

switch may cause loops in your network that STP may not be able to detect, in

all cases.

ꢀ forward-delay <seconds> - Time the switch waits between transition from

listening to learning and from learning to forwarding states. The range is 4 to 30.

The default is 15.

ꢀ hello-time <seconds> - Time (in seconds) between messages transmitted when

the switch is root. The range is 1 to 10. The default is 2.

ꢀ maximum-age <seconds> - Maximum message age (in seconds) of received

STP information before it is discarded. The range is 6 to 40. The default is 20.

ꢀ priority <0..65535> - Switch (or bridge) priority used along with the switch

MAC address to determine which device is the root. The default is 32768.

27ꢀ

2.11 IP

2.11.1 IP commands - EXEC level

show ip

Displays the IP configuration on the switch.

Output Format

There are two different IP configuration screens. The first is displayed when no

vlans are configured on the switch; the second is displayed when vlans are

configured.

Switch Configuration - Internet (IP) Serviceꢀ

Default Gateway: 192.32.36.1ꢀ

TimeP Config [DHCP]: DHCP

TimeP Poll Interval (min) [720]: 720ꢀ

IP Config [DHCP/Bootp] : DHCP/Bootpꢀ

IP Address : 192.32.36.96

Subnet Mask : 255.255.255.192ꢀ

Switch Configuration - Internet (IP) Serviceꢀ

Default Gateway: 192.32.36.1ꢀ

TimeP Config [DHCP]: DHCP

TimeP Poll Interval (min) [720]: 720ꢀ

VLAN

------------ + ----------ꢀ --------------- ---------------

DEFAULT_VLAN | Manual 192.32.36.91 255.255.255.192ꢀ

vlan2 | DHCP/Bootpꢀ

IP Config

IP Address

Subnet Maskꢀ

28ꢀ

show ip authorized-managers

Displays the current configuration's IP managers access records.

Output Format:

Switch Configuration - IP Managersꢀ

Authorized Manager IP IP Mask

Access Levelꢀ

----------------------ꢀ -------------------- ---------------------

192.32.36.78

255.255.255.255

Managerꢀ

show arp

Displays the ARP cache of the switch.

Output Format

ARP Cacheꢀ

IP Address

--------------ꢀ ------------- -----------

192.32.36.78 080009-012345 orange-lanꢀ

MAC Address

VLANꢀ

show ip route

Displays active IP route entries used by the switch.

Output Format

IP Route Entriesꢀ

Network Addr Network Mask Gateway

Port Cost Typeꢀ

--------------ꢀ ------------- ----------- ---- ---- ----

192.32.36.0 255.255.255.0 192.32.36.1 A1 Rꢀ

29ꢀ

show timp

Displays active Timep configuration.

Output Format

Timep Configurationꢀ

Time Sync Mode: Timepꢀ

TimeP Mode [Disabled] : Manual

Server Address : 15.29.16.105ꢀ

Poll Interval (min) [720] : 600ꢀ

show sntp

Displays active SNTP configuration.

Output Format

SNTP Configurationꢀ

Time Sync Mode: Timepꢀ

SNTP Mode [Disabled] : Disabledꢀ

Poll Interval (min) [720] : 600ꢀ

30ꢀ

2.11.2 IP commands - Configuration level

[no] ip authorized-managers <ip-addr>

[mask <ip-mask>]

[operator | manager]

Sets the IP addresses you will allow to access the switch’s Web browser interface, to

telnet to the switch console, and to perform TFTP operations. A maximum of 10

addresses is supported.

Parameters:

ꢀ <ip-addr> - The IP address of an authorized manager.

ꢀ mask <ip-mask> - The default mask is 255.255.255.255. A mask that allows you

to define which portions of the listed IP address need to be matched by an

incoming request. For example, with an authorized address of 10.8.11.1 and a

mask of 255.255.255.255, only access from 10.8.11.1 is allowed. With a mask of

255.255.255.0, access from any IP address with 10.8.11.x is allowed.

ꢀ <operator | manager> - The default access level is manager. A designation of

the management capabilities that are accessible to the authorized manager.

manager allows full access to all web browser and the CLI for viewing and

setting the switch configuration, and for performing all other interface

operations, including all TFTP operations. operator allows view-only access

from the web browser and the CLI, but does not allow changing the switch

configuration or any TFTP operations.

[no] timesync <timep | sntp >

Configures the network time protocol to be used by the switch.

[no] timep <dhcp | manual <ip-addr>> [interval <1..9999>]

Configures Timep on the switch.

Parameters:

ꢀ <dhcp | manual> - The method the switch uses to acquire the Timep server

address: dhcp - from a DHCP server; manual - you manually enter the Timep

server address; disable - the switch will not attempt to get its time from a Timep

server.

ꢀ interval <1..9999> (default is 720) How often (in minutes) the switch tries to

get the current time.

ꢀ <ip-addr> - The IP address of the Timep server that the switch gets the current

time from.

31ꢀ

[no] sntp < server <ip-addr> [version]> [poll-interval <30-720>]

Configures SNTP on the switch.

ip default-gateway <ip-addr>

Assigns an IP address to be used as the default gateway when the switch is not in

routing mode.

ip route <<ip-addr>/<1..32> | <ip-addr> <ip-mask>> <ip-addr>

Used to configure a static IP route for the switch.

ip ttl <value>

Sets the maximum time that a packet will live on the network.

[no] arp <ip-addr> [mac-addr]

Used to modify the arp cache.

32ꢀ

2.11.3 IP commands - VLAN Interface level

[no] ip address <dhcp-bootp | <<ip-addr>/<1..32> |

<ip-addr> <ip-mask>] [secondary]>

This command configures the IP address for the switch. Note, by default this

command uses a VLAN identifier of one. Although this command is duplicated at

the VLAN context level, it is defined here for those customers who do not want to

be exposed to VLAN distinctions.

Parameters:

ꢀ dhcp-bootp - The method the switch uses to acquire its IP Service configuration:

dhcp-bootp - the switch attempts to get its IP configuration, or its complete

configuration, from a DHCP/Bootp server, depending on how the server is

configured. If the 'address' is specified at the command line then the interface uses

a 'manual' method in which the IP address and subnet mask are explicitly specified.

If the modal operation 'no' is specified for the interface then the interface becomes

disabled and all IP communication with the switch ceases. This includes SNMP,

management, Web browser access, and telnet access.

ꢀ <ip-addr>/<1..32> - IP address for the switch (or VLAN) IP interface. <1..32> is

the number of bits present in the subnet mask used by all devices in the IP subnet

being configured.

ꢀ <ip-addr> <ip-mask> - This is an alternative syntax for specifying the IP address

and subnet mask described above.

33ꢀ

2.12 SNMP

2.12.1 SNMP commands - EXEC level

show snmp-server

Displays the SNMP communities which may be used to access the switch along with

the network management stations configured to receive SNMP traps.

Output Format:

SNMP Serverꢀ

Community Name MIB View Write Accessꢀ

--------------ꢀ -------- -------------

public

Manager Unrestrictedꢀ

Send Authentication Traps [No] : Noꢀ

Address

----------------------ꢀ ---------------- -------------------

192.32.36.78 public Noneꢀ

Community

Events Sent in Trapꢀ

34ꢀ

2.12.2 SNMP commands – Configuration Level

[no] snmp-server community <community-name>

[manager | operator]

[restricted | unrestricted]

Used to configure a new SNMP community or to edit the configuration for an

existing one

Parameters:

ꢀ <community-name> - Enter (up to 16 characters) the SNMP community name.

ꢀ [manager | operator] - Manager - the community can access all MIB objects;

Operator - the community can access all except the CONFIG MIB.

ꢀ [restricted | unrestricted] - Unrestricted - any MIB variable that has read/write

access can be set; Restricted - MIB variables cannot be set, only read.

[no] snmp-server host <ip-addr> <community-name> [none | all | non-info | critical |

debug]

Configures which network management stations will receive SNMP event log

messages from the switch and the types of events for which the switch will send

these messages.

Parameters:

ꢀ <ip-addr> - Address of the network management station.

ꢀ <community-name> - The name of the SNMP community to which the network

management station belongs.

ꢀ [none | all | non-info | critical | debug] - The level of Switch events that will

generate a Trap to be sent: None - send no log message; All - send all log

messages; Not INFO - send each log message that is not informational-only;

Critical - send critical-level log messages; Debug (reserved for Internal use).

[no] snmp-server enable traps authentication

Enables authentication traps to be sent when a management station attempts an

unauthorized access.

35ꢀ

2.13 VLAN Configurationꢀ

2.13.1 VLAN commands - EXEC levelꢀ

show vlansꢀ

Displays the current VLANs.

Output Format:

Switch Configuration - VLAN Informationꢀ

VLAN Support [No] : Yesꢀ

Maximum VLANs to support [8] : 8ꢀ

Primary VLAN: DEFAULT_VALNꢀ

802.1Q VLAN ID Name ꢀ

Type

Statusꢀ

--------------ꢀ ------------ ------ ------

DEFAULT_VLAN ꢀ Static Upꢀ

show vlans <vlan-id>

Displays which ports are assigned to particular VLANs.

Output Format:

Switch Configuration - VLAN - VLAN Port Assignmentꢀ

Port DEFAULT_VLAN

vlan2

| Port DEFAULT_VLAN

vlan2ꢀ

---- + ------------ ------------ | ---- + ------------ꢀ ------------

| Untagged

| 9

| Untagged

Noꢀ

| 10 | Untagged

| 11 | Untagged

| 12 | Untagged

| 13 | Untagged

| 14 | Untagged

| 15 | Untagged

| 16 | Untagged

2.13.2 VLAN commands – Configuration Level

max-vlans <1..256>

Sets the maximum number of VLANs on the system. The default value is 8.

36ꢀ

primary-vlan <vlan-id>

Sets the primary VLAN used for network management.

[no] vlan <vlan-id>

Creates a new VLAN or changes the system context to the VLAN configuration

level. Note that vlan-name can be substituted for the vlan-id when using this command.

static-vlan <vlan-id>

Creates a new static VLAN from one which has been dynamically created by GVRP.

[no] vlan-support

Enables VLAN support on the switch.

2.13.3 VLAN Interface commands

To enter the VLAN Interface Configuration level, use the vlan command described above.

Note that any of the following commands can be appended to the vlan command to simply

change the configuration. For example:

HP 4108GL(config)# add vlan 2 name orange-lanꢀ

name <vlan-name>

Changes the current VLAN identifier’s name.

[no] tagged <port-list>

Assigns ports to current VLAN identifier as tagged.

[no] untagged <port-list>

Assigns ports to current VLAN identifier as untagged.

[no] forbid <port-list>

Forbids the ports from ever becoming a member of the current VLAN.

37ꢀ

auto <port-list>

Causes each port identified in the port-list to learn their VLAN membership using

the Group VLAN Registration Protocol (GVRP). This command is only valid when

GVRP is enabled.

2.14 GVRP

2.14.1 GVRP commands - EXEC level

show gvrp

Displays the current VLANs.

Output Format:

Switch Configuration - GVRP Informationꢀ

GVRP Enabled [No] : Yesꢀ

Port Type

| Unknown VLANꢀ

---- -------- + ------------ꢀ

10/100TX | Learnꢀ

2.14.2 GVRP commands – Configuration level

[no] gvrp

Enables the Group VLAN Registration Protocol (GVRP) on the switch.

2.14.3 Ethernet Interface Configuration commands

unknown-vlans <learn | block |disable>

Defines what the port will do when it encounters GVRP packet requested it to join a

VLAN. If learn is specified then the port will join the advertised VLAN and

propagate a VLAN join requests through all other forwarding ports that are

participating in GVRP. If block is specified then the port will not join the advertised

VLAN and will not propagate any VLAN joins for the advertised VLAN.

38ꢀ

2.15 IGMP

2.15.1 IGMP Commands – EXEC Level

show ip igmp [vlan-id] config

Displays IGMP configuration information.

Output Format:

Switch Configuration - IGMP Serviceꢀ

IGMP Enabled [No] : Noꢀ

Forward with High Priority [No] : Noꢀ

Port

Type

IP Mcast | Port

Type

IP Mcast

---- -------- + -------- | ---- -------- + --------

10/100TX | Auto

| 11

| 12

| 13

| 14

| 15

| 16

10/100TX | Auto

| Mesh Mesh

| Auto

show ip igmp [<vlan-id> | group <group-address>]

When IGMP is enabled, this command shows a summary of the IGMP status for all

the IP Multicast groups used by the selected VLAN. If the feature is not enabled,

then this command displays “IGMP not enabled”.

Output Format:

Status and Counters - IP Multicast (IGMP) Statusꢀ

Active Group Addresses Reports Queries Querier Access Portꢀ

----------------------ꢀ ------- ------- ----------------------

Active Group Address :ꢀ

Port

Type

Access ꢀ

Age timer Leave timerꢀ

----ꢀ -------- ----------- --------- -----------

Active Group Address :ꢀ

Port

Type

Access ꢀ

Age timer Leave timerꢀ

----ꢀ -------- ----------- --------- -----------

39ꢀ

2.15.2 IGMP Configuration commands – Vlan Interface level

[no] ip igmp

Enables the IP Multicast (IGMP) feature for IGMP communication between

Multicast Routers, Multicast Servers, and Multicast Clients connected to the switch

or selected VLAN.

[no] ip igmp high-priority-forward

Determines whether the switch forwards all IP Multicast traffic at high priority.

[no] ip igmp querier

Determines whether the switch is querier or not.

ip igmp <auto|block|forward> <port-list>

Instructs the switch's IGMP feature to control the action taken with an IGMP

frame.

40ꢀ

2.16 Port Monitoringꢀ

2.16.1 Port Monitoring commands - EXEC levelꢀ

show mirror-portꢀ

Displays the configuration of the monitoring port.

Output Format:

Switch Configuration - Network Monitoring Portꢀ

Monitoring Enabled [No] : Yesꢀ

Monitoring Port : 3ꢀ

Monitor : Portsꢀ

Port

Type

Action

| Port

Type

Action

---- -------- + ------- | ---- -------- + -------

10/100TX |

| 11

| 12

| 13

| 14

| 15

| 16

10/100TX |

| Mesh Mesh

2.16.2 Port Monitoring commands - Configuration level

[no] mirror-port [<port-num>]

This command defines the switch port that will be used as the Monitoring Port for

diagnostic purposes. The switch ports that will be monitored are defined through the

monitor command at the Ethernet Interface Configuration Level. All the network

traffic seen by the monitored ports is copied to the Monitoring Port to which a

network analyzer can be attached.

Note: When monitoring multiple ports in a busy network, some frames may not be

copied to the monitoring port.

Parameters:

ꢀ port-num - Port that will be acting as the monitoring port. A configured trunk port

cannot be used.

41ꢀ

2.16.3 Port Monitoring commands - VLAN Interface level

[no] monitor

Used to enable/disable monitoring of the VLAN.

2.16.4 Port Monitoring commands - Ethernet Interface level

[no] monitor

Used to enable/disable monitoring of the port.

2.17 Port Securityꢀ

2.17.1 Port Security commands - EXEC levelꢀ

show port-securityꢀ

Displays the per-port security configuration for the switch.

Output Format:

Switch Configuration - Port Securityꢀ

Port Learn Mode Action

------ ---------- --------------------

Continuous None

42ꢀ

show port-security [ethernet] <port-list>

Displays the port security configuration for an individual port.

Output Format:

Switch Configuration - Port Securityꢀ

Port : 3ꢀ

Learn Mode [Continuous] : Continuousꢀ

Action [None] : Noneꢀ

show port-security intrusion-log

Displays information on any port security intrusions that have occurred on the

switch.

Output Format:

Status and Counters – Intrusion Logꢀ

Port MAC Address

Date / Timeꢀ

----ꢀ ------------- --------------------------

2.17.2 Port Security commands - Configuration level

port-securityꢀ <port-list>

[learn-mode < continuous | static >]

[address-limit <1..8>]

[action <none | send-alarm | send-disable>]

[no] port-security <port-list>

[mac-address <mac-addr>]

This command configures port security on the switch.

Parameters:

ꢀ learn-mode - If continuous is selected, the switch learns any new address from

packets received on the port. If static is selected, up to the number of addresses

43ꢀ

defined by the "address-limit" parameter are learned or entered for the port.

These addresses are static; they are not aged out.

ꢀ addr-limit <1..8> - This parameter is valid only if static is selected for the

learn-mode. This parameter defines the number of network devices that are

authorized to communicate through the switch port. Up to 8 devices can be

authorized for any port.

ꢀ addr-list <mac-addr> - This parameter is valid only if static is selected for the

learn-mode. If you enter no authorized addresses, the switch will learn and

configure authorized addresses as it detects them on the port, up to the address-

limit number of addresses, and make these the static authorized addresses for the

port. If you enter fewer addresses than the Address Limit, the switch will learn

the additional addresses up to the address-limit. If you enter more addresses than

the address-limit, an error message is displayed when you attempt to Save the

configuration.

ꢀ action - Indicates the action the switch will take if an intruder is detected on the

port.

44ꢀ

Console Menu

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Main Menuꢀ

1. Status and Counters...ꢀ

2. Switch Configuration...ꢀ

3. Console Passwords…ꢀ

4. Event Logꢀ

5. Command Line (CLI)ꢀ

6. Reboot Switchꢀ

7. Download OSꢀ

8. Run Setupꢀ

0. Logoutꢀ

Provides the menu to display configuration, status, and counters.ꢀ

To select menu item, press item number, or highlight item and press <Enter>.ꢀ

3.1 Status and Counters

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters Menuꢀ

1. General System Informationꢀ

2. Switch Management Address Informationꢀ

3. Module Informationꢀ

4. Port Statusꢀ

5. Port Countersꢀ

6. Address Tableꢀ

7. Port Address Tableꢀ

8. Spanning Tree Informationꢀ

0. Return to Main Menu...ꢀ

Displays switch management information including software versions.ꢀ

To select menu item, press item number, or highlight item and press <Enter>.ꢀ

45ꢀ

3.1.1 General System Information

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters - General System Informationꢀ

System Contact

System Location

:ꢀ

Firmware revision : E.08.XX

Base MAC Addr

Serial Number

: 0060b0-882200ꢀ

:ꢀ

ROM Version

: E.05.X1

Up Time

CPU Util (%)

: 40 mins

: 1

Memory

- Total

Free

: 5,803,088ꢀ

: 2,230,032ꢀ

IP Mgmt - Pkts Rx : 11

Pkts Tx : 0

Packet

Buffers ꢀ Free

- Total

: 438ꢀ

: 272ꢀ

Lowest : 199ꢀ

Missed : 0ꢀ

Actions->

Back

Helpꢀ

Return to previous screen.ꢀ

Use arrow keys to change action selection and <Enter> to execute action.ꢀ

3.1.2 Management Address Information

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters - Management Address Informationꢀ

Time Server Address :ꢀ

MAC Address

IP Address

: 0060b0-882200ꢀ

: 10.0.8.105ꢀ

IPX Network Number :ꢀ

Actions->

Back

Helpꢀ

Return to previous screen.ꢀ

Use arrow keys to change action selection and <Enter> to execute action.ꢀ

46ꢀ

3.1.3 Module Information

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters - Module Informationꢀ

Slot

Module Type

Module Descriptionꢀ

----ꢀ --------------- ---------------------------------------------

Slot Availableꢀ

Actions->

Back

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

3.1.4 Port Status

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters - Port Statusꢀ

Intrusion

Alert

Flow

Ctrl

Bcastꢀ

Limitꢀ

Port

Type ꢀ

Enabled Status

Mode

----ꢀ -------- --------- ------- ------ ---------- --------- ------

10/100TX ꢀ No

Yes

100HDx

10HDx

off

0ꢀ

Down

Actions->

Back

Intrusion log

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

47ꢀ

3.1.5 Port Counters

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters - Port Countersꢀ

Port

Total Bytes

Total Frames

Errors Rx

Drops Txꢀ

----ꢀ ------------- ------------- ------------- -------------

16,448

217

0ꢀ

Actions->

Back

Show details

Reset

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

3.1.5.1 Port Counters Details

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters - Port Counters - Port 1ꢀ

Link Status

: Upꢀ

Bytes Rx

Unicast Rx

: 16,088

: 88

Bytes Tx

Unicast Tx

: 360ꢀ

: 4ꢀ

Bcast/Mcast Rx : 124

Bcast/Mcast Tx : 1ꢀ

FCS Rx

: 0

Drops Tx

Collisions Tx

Late Colln Tx

Excessive Colln : 0ꢀ

Deferred Tx : 0ꢀ

: 0ꢀ

Alignment Rx

Runts Rx

Giants Rx

Total Rx Errors : 0

Actions->

Back

Reset

Helpꢀ

Return to previous screen.ꢀ

Use arrow keys to change action selection and <Enter> to execute action.ꢀ

48ꢀ

3.1.6 Address Table

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters - Address Table – VLAN ID 23ꢀ

MAC Address

Located on Portꢀ

-------------ꢀ ---------------

0060b0-e26440 1ꢀ

080009-092851 1ꢀ

080009-76ac55 1ꢀ

080009-97aad2 1ꢀ

Actions->

Back

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

3.1.7 Port Address Table

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters - Port Address Table - Port A1ꢀ

MAC Addressꢀ

-------------ꢀ

0060b0-e26440ꢀ

080009-092851ꢀ

080009-76ac55ꢀ

080009-97aad2ꢀ

Actions->

Back

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

49ꢀ

3.1.8

Spanning Tree Information

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters - Spanning Tree Informationꢀ

STP Enabled

Switch Priority

Hello Time

: Yesꢀ

: 32,768ꢀ

: 2ꢀ

Max Age

: 20ꢀ

Forward Delay

: 15ꢀ

Topology Change Count : 1ꢀ

Time Since Last Change : 4 minsꢀ

Root MAC Address

Root Path Cost

Root Port

: 0060b0-885a80ꢀ

: 0ꢀ

: This switch is rootꢀ

Root Priority

: 32768ꢀ

Actions->

Back

Show ports

Helpꢀ

Return to previous screen.ꢀ

Use arrow keys to change action selection and <Enter> to execute action.ꢀ

3.1.8.1 Spanning Tree Port Information

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Status and Counters - Spanning Tree - Port Informationꢀ

Port

Type

Cost

Priority

State

Designated Bridge

---- ------------ ----- -------- ---------- -----------------

10/100TX

128 Forwarding 0060b0-885a80

128 Disabled

128 Disabledꢀ

Actions->

Back

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

50ꢀ

3.2 Configuration Menu

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration Menuꢀ

1. System Informationꢀ

2. Port/Trunk Settingsꢀ

3. Network Monitoring Portꢀ

4. Spanning Tree Operationꢀ

5. IP Configurationꢀ

6. SNMP Community Namesꢀ

7. Authorized Managersꢀ

8. VLAN Menu...ꢀ

0. Return to Main Menu...ꢀ

Configures system-level information including system identification.ꢀ

To select menu item, press item number, or highlight item and press <Enter>.ꢀ

51ꢀ

3.2.1 System Information

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration - System Informationꢀ

System Name : DEFAULT_CONFIGꢀ

System Contact :ꢀ

System Location :ꢀ

Inactivity Timeout (min) [0] : 0 ꢀ

Inbound Telnet Enabled [Yes] : Yes ꢀ

Address Age Interval (min) [5] : 5ꢀ

Web Agent Enabled [Yes] : Yesꢀ

Time Zone [0] : 0ꢀ

Daylight Time Rule [None] : Noneꢀ

Actions->

Cancel

Edit

Save ꢀ

Helpꢀ

Cancel changes and return to previous screen.ꢀ

Use arrow keys to change action selection and <Enter> to execute action.ꢀ

3.2.2 Port/Trunk Settings

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration – Port/Trunk Settingsꢀ

Port

Type

Enabled

Mode

Flow Ctrl

Group

Typeꢀ

---- -------- + -------ꢀ ---------- --------- ----------- ----------

A10

A11

10/100TX | Yes ꢀ

Auto

Disable

Dyn

Trk1

LACP

Trunk

Trk2

Dyn

Trk2

MESH

FEC

LACP

FEC

Actions->

Cancel

Edit

Save

Helpꢀ

Cancel changes and return to previous screen.ꢀ

Use arrow keys to change action selection and <Enter> to execute action.ꢀ

52ꢀ

3.2.3 Network Monitoring Port

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration – Network Monitoring Portꢀ

Monitoring Enabled [No] : Yesꢀ

Monitoring Port : A1ꢀ

Monitor : Portsꢀ

Port

Type

Action ꢀ

Port ꢀ Type

Actionꢀ

---- -------- + -------ꢀ

A7 ꢀ 10/100TX |ꢀ

A8 ꢀ 10/100TX |ꢀ

B1 ꢀ 10/100TX |ꢀ

B2 ꢀ 10/100TX |ꢀ

B3 ꢀ 10/100TX |ꢀ

B4 ꢀ 10/100TX |ꢀ

10/100TX | ꢀ

Actions->

Cancel

Edit

Save ꢀ

Helpꢀ

Cancel changes and return to previous screen.ꢀ

Use arrow keys to change action selection and <Enter> to execute action.ꢀ

3.2.4 Spanning Tree Operation

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration – Spanning Tree Operationꢀ

Spanning Tree Enabled [No] : Noꢀ

STP Priority [32768] : 32768 ꢀ

Hello Time [2] : 2ꢀ

Max Age [20] : 20 ꢀ

Forward Delay [15] : 15ꢀ

Port

Type

Cost ꢀ Pri Modeꢀ

---- -------- + -----ꢀ --- ----

10/100TX | 10 ꢀ

128 Normꢀ

Actions->

Cancel

Edit

Save

Helpꢀ

Cancel changes and return to previous screen.ꢀ

Use arrow keys to change action selection and <Enter> to execute action.ꢀ

53ꢀ

3.2.5 IP Configuration

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration - Internet (IP) Serviceꢀ

Default Gateway : 10.0.8.1ꢀ

Time Protocol Config [DHCP] : DHCPꢀ

TimeP Poll Interval (min) [720] : 720ꢀ

IP Config [DHCP/Bootp] : Manualꢀ

IP Address : 10.0.8.105ꢀ

Subnet Mask : 255.255.248.0ꢀ

Actions->

Cancel

Edit

Save

Helpꢀ

Cancel changes and return to previous screen.ꢀ

Use arrow keys to change action selection and <Enter> to execute action.ꢀ

With multiple Vlans configured:

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration - Internet (IP) Serviceꢀ

Default Gateway : 10.0.8.1ꢀ

Time Protocol Config [DHCP] : DHCPꢀ

TimeP Poll Interval (min) [720] : 720ꢀ

VLAN

IP Config

Ip Address

Subnet Maskꢀ

----------- + ---------ꢀ ------------ ---------------

Orange Lan | Manual

10.0.8.105

255.255.248.0ꢀ

Yellow Lan | Disabledꢀ

Actions->

Cancel

Edit

Save

Helpꢀ

Cancel changes and return to previous screen.ꢀ

Use arrow keys to change action selection and <Enter> to execute action.ꢀ

54ꢀ

3.2.6 SNMP Communities

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration - SNMP Communitiesꢀ

Community Name

MIB View Write Accessꢀ

----------------ꢀ -------- ------------

public

Manager

Unrestrictedꢀ

Actions->

Back

Add

Edit

Delete

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to change record selection, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

3.2.7 Authorized Managers

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration – Authorized Managersꢀ

Authorized Manager

--------------------ꢀ ---------------

15.29.16.80 255.255.255.255

IP Mask

Access Levelꢀ

------------

Managerꢀ

Actions->

Back

Add

Edit

Delete

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to change record selection, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

55ꢀ

3.2.8 VLAN Menu

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration - VLAN Menuꢀ

1. VLAN Supportꢀ

2. VLAN Namesꢀ

3. VLAN Port Assignmentꢀ

4. Return to Previous Menu...ꢀ

0. Return to Main Menu...ꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to change record selection, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

3.2.8.1 VLAN Support

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration - VLAN Supportꢀ

Activate VLANs [No] : Yesꢀ

Maximum Vlnas to support [8] : 8ꢀ

Primary VLAN : DEFAULT_VLANꢀ

GVRP Enabled [No] : Noꢀ

Actions->

Back

Add

Edit

Delete

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to change record selection, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

56ꢀ

3.2.8.2 VLAN Names

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration - VLAN Namesꢀ

Name

802.1Q VLAN IDꢀ

------------ꢀ --------------

DEFAULT_VLAN 1ꢀ

Actions->

Back

Add

Edit

Delete

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow keys to change record selection, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

3.2.8.3 VLAN Port Assignment

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Configuration - VLAN Port Assignmentꢀ

Port

DEFAULT_VLAN

| Port

| ---- + ------------ꢀ

DEFAULT_VLANꢀ

---- + ------------

| Tagged ꢀ

| E1

| E2

| E3

| E4

| E5

| E6

| E7

| E8

| E9

| Untaggedꢀ

A10 | Tagged ꢀ

A11 | Tagged ꢀ

A12 | Tagged ꢀ

| E10 | Untaggedꢀ

| E11 | Untaggedꢀ

| E12 | Untaggedꢀ

Actions->

Cancel

Edit

Save

Helpꢀ

Use arrow keys to change field selection, <Space> to toggle field choices,ꢀ

and <Enter> to go to Actions.ꢀ

57ꢀ

3.3 Password Menu

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Set Password Menuꢀ

1. Set Operator Passwordꢀ

2. Set Manager Passwordꢀ

3. Delete Password Protectionꢀ

4. Return to Previous Menu...ꢀ

0. Return to Main Menu...ꢀ

Prompts you to enter an Operator-level password.ꢀ

To select menu item, press item number, or highlight item and press <Enter>.ꢀ

3.4 Event Log

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

M 01/01/90 00:00:07 sys: 'System reboot due to Power Failure'ꢀ

I 01/01/90 00:00:07 system: --------------------------------------------------ꢀ

I 01/01/90 00:00:07 system: System went down without saving crash informationꢀ

I 01/01/90 00:00:29 timep: timep client enabledꢀ

I 01/01/90 00:00:29 garp: GARP Protocol enabledꢀ

I 01/01/90 00:00:31 tftp: Enable succeededꢀ

I 01/01/90 00:00:31 system: System Booted.ꢀ

I 01/01/90 00:00:37 ports: port 1 is now on-lineꢀ

I 01/01/90 00:00:37 ip: network enabled on 10.0.8.105ꢀ

I 01/01/90 00:39:55 mgr: SME CONSOLE Session - MANAGER Mode establishedꢀ

---- Log events stored in memory 1-13. Log events on screen 1-13.ꢀ

Actions->

Back

End

Helpꢀ

Return to previous screen.ꢀ

Use up/down arrow scroll log one line, left/right arrow keys toꢀ

change action selection, and <Enter> to execute action.ꢀ

58ꢀ

3.5 Download Screen

HP ProCurve Switch xxxxx ꢀ

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Download OSꢀ

Current Firmware revision : E.08.XXꢀ

Method [TFTP] : TFTPꢀ

TFTP Server :ꢀ

Remote File Name :ꢀ

Actions->

Cancel

Edit

eXecute

Helpꢀ

Select the file transfer method (TFTP and XMODEM are currently supported).ꢀ

Use arrow keys to change field selection, <Space> to toggle field choices,ꢀ

and <Enter> to go to Actions.ꢀ

3.6 Run Setup

HP ProCurve Switch xxxxx

01-Apr-2000ꢀ

==========================- CONSOLE - MANAGER MODE -============================ꢀ

Switch Setupꢀ

System Name : HP ProCurve Switch xxxxxꢀ

System Contact :ꢀ

Manager Password :

Confirm Password:ꢀ

Logon Default : Menu

Community Name : public

Time Zone [0] : 0ꢀ

Spanning Tree Enabled [No] : Noꢀ

Default Gateway : 10.0.8.1ꢀ

TimeP Config [DHCP] : DHCPꢀ

IP Config [DHCP/Bootp] : Manualꢀ

IP Address : 10.0.8.80

Subnet Mask : 255.255.248.0ꢀ

Actions->

Cancel

Edit

eXecute

Helpꢀ

Select the file transfer method (TFTP and XMODEM are currently supported).ꢀ

Use arrow keys to change field selection, <Space> to toggle field choices,ꢀ

and <Enter> to go to Actions.ꢀ

59ꢀ

Index

ip route ..............................................................32ꢀ

ip ttl ...................................................................32ꢀ

Aꢀ

aaa authentication console ................................16ꢀ

aaa authentication telnet....................................16ꢀ

arp......................................................................32ꢀ

auto....................................................................38ꢀ

auto-tftp.............................................................14ꢀ

Kꢀ

kill .......................................................................7ꢀ

Lꢀ

lacp....................................................................23ꢀ

link-test................................................................9ꢀ

logout ..................................................................5ꢀ

Bꢀ

boot......................................................................6ꢀ

broadcast-limit ..................................................22ꢀ

Mꢀ

Cꢀ

mac-age-time.....................................................14ꢀ

max-vlans..........................................................36ꢀ

menu....................................................................5ꢀ

mirror-port.........................................................41ꢀ

monitor..............................................................42ꢀ

cdp.....................................................................17ꢀ

cdp enable .........................................................17ꢀ

cdp holdtime......................................................17ꢀ

cdp timer ...........................................................17ꢀ

clear arp...............................................................7ꢀ

clear intrusion-log ...............................................8ꢀ

clear statistics......................................................8ꢀ

configure .............................................................5ꢀ

console ..............................................................14ꢀ

copy.................................................................6, 9ꢀ

Nꢀ

name..................................................................37ꢀ

Pꢀ

page .....................................................................6ꢀ

password............................................................16ꢀ

ping....................................................................10ꢀ

port-security ......................................................43ꢀ

primary-vlans ....................................................37ꢀ

print .....................................................................7ꢀ

Dꢀ

daylight-time-rule .............................................15ꢀ

disable ...............................................................22ꢀ

Eꢀ

Rꢀ

enable ............................................................5, 22ꢀ

end.......................................................................5ꢀ

erase flash............................................................6ꢀ

erase startup-config.............................................6ꢀ

exit.......................................................................5ꢀ

reload...................................................................7ꢀ

repeat...................................................................6ꢀ

Sꢀ

setmib..................................................................9ꢀ

setup ....................................................................5ꢀ

show arp ............................................................29ꢀ

show boot-history................................................7ꢀ

show cdp ...........................................................17ꢀ

show console.....................................................11ꢀ

show flash ...........................................................9ꢀ

show gvrp..........................................................38ꢀ

show history ........................................................7ꢀ

show interfaces..................................................22ꢀ

show interfaces config ......................................20ꢀ

show ip ..............................................................28ꢀ

show ip authorized-managers ...........................29ꢀ

show ip igmp.....................................................39ꢀ

show ip igmp config..........................................39ꢀ

show ip route.....................................................29ꢀ

show lacp...........................................................24ꢀ

show logging.......................................................7ꢀ

show mac-address ...................................... 11, 12ꢀ

Fꢀ

flow-control.......................................................23ꢀ

Gꢀ

getmib..................................................................8ꢀ

gvrp ...................................................................38ꢀ

Hꢀ

hostname ...........................................................15ꢀ

Iꢀ

interface...............................................................5ꢀ

ip 33ꢀ

ip authorized-managers.....................................31ꢀ

ip default-gateway.............................................32ꢀ

ip igmp ..............................................................40ꢀ

ip igmp high-priority-forward...........................40ꢀ

ip igmp querier..................................................40ꢀ

60ꢀ

show management.............................................12ꢀ

show mirror-port ...............................................41ꢀ

show modules....................................................13ꢀ

show port-security.......................................42, 43ꢀ

show port-security intrusion log .......................43ꢀ

show running-config ...........................................7ꢀ

show snmp-server community..........................34ꢀ

show sntp...........................................................30ꢀ

show spanning-tree ...........................................26ꢀ

show spanning-tree config ................................25ꢀ

show stack.........................................................18ꢀ

show startup-config.............................................7ꢀ

show statistics ...................................................20ꢀ

show system-information..................................13ꢀ

show tacacs .......................................................17ꢀ

show tech.............................................................9ꢀ

show timep ........................................................30ꢀ

show trunks .......................................................23ꢀ

show version .......................................................9ꢀ

show vlans.........................................................36ꢀ

snmp-server.......................................................15ꢀ

snmp-server community....................................35ꢀ

snmp-server enable traps...................................35ꢀ

snmp-server host ...............................................35ꢀ

sntp....................................................................32ꢀ

spanning-tree.....................................................26ꢀ

speed-duplex .....................................................23ꢀ

stack ..................................................................18ꢀ

stack auto-grab..................................................19ꢀ

stack auto-join...................................................19ꢀ

stack commander...............................................18ꢀ

stack join ...........................................................18ꢀ

stack member ....................................................18ꢀ

stack transmission-interval................................19ꢀ

static-vlan..........................................................37ꢀ

Wꢀ

walkmib...............................................................8ꢀ

web-management ..............................................16ꢀ

write memory ......................................................6ꢀ

write terminal ......................................................6ꢀ

Tꢀ

tacacs-server host..............................................17ꢀ

tacacs-server timeout ........................................17ꢀ

tagged................................................................37ꢀ

telnet....................................................................8ꢀ

telnet-server.......................................................16ꢀ

time....................................................................15ꢀ

timep..................................................................31ꢀ

timesync ............................................................31ꢀ

time-zone...........................................................15ꢀ

trunk ..................................................................24ꢀ

Uꢀ

unknown-vlans..................................................38ꢀ

untagged............................................................37ꢀ

Vꢀ

vlan................................................................6, 37ꢀ

vlan-support ......................................................37ꢀ

61ꢀ

Xerox Dc230lp User Manual
Xerox C424 User Manual
Whirlpool Air Cleaner Wp Ap510 User Manual
Spt Wa 1310e User Manual
Sharp Cv10nh User Manual
Sharp Af R120dx User Manual
Samsung Sf 560 User Manual
NEC MULTISYNC LCD1990SXI User Manual
Mitsubishi Electronics Pe 10myc User Manual
BLACK DECKER GCO1200 User Manual