Xerox Dc230lp User Manual

7+(ꢀ'2&80(17ꢀ&203$1<  
ꢀꢁꢂꢃꢀ  
DC230LP Windows NT® 4.0 TCP/IP Quick Install  
IP Address  
(current entry)  
Installation Requirements:  
>
2.  
Access the System Administration menus:  
d) Press [ ].  
displays.  
To install the DC230LP in a DHCP environment,  
exclude the addresses assigned to the  
DC230LP at the DHCP server.  
a) Press [Online] to take the printer off  
4.  
IP Address Setup (skip this step if using  
RARP):  
Printer Off Line  
line.  
displays.  
IP Address  
(current entry)  
=
*
Main Menu  
Before Installation:  
>
a) Press [ ].  
displays.  
b) Press [Menu].  
displays.  
Record the following information for use during  
setup at the DC230LP:  
Note: Use zeros to supplement each address  
segment if fewer than 3 digits are used; e.g.,  
13.252.25.08 = 013.252.025.008.  
c) Press [ ], then press [ ] or [ ] until  
System  
Administration  
>
TCP/IP Address:________________________  
Gateway Address: ______________________  
Subnet Mask: __________________________  
Broadcast Address: _____________________  
Host Name:____________________________  
displays.  
b) Use the [ ] or [ ] key to enter the  
Enter Password  
>
d) Press [ ].  
displays.  
first digit of the IP Address.  
c) Press [ ] to move to the next digit.  
Repeat this procedure to enter the  
entire IP Address.  
e) Use the [ ] and [ ] keys to enter  
[2222].  
Note: 2222 is the factory default password and  
may be changed to suit your needs. Refer to the  
DC230LP System Administration Guide,  
Network Installation and Troubleshooting.  
d) Press [Enter]. **SAVED**displays  
momentarily, followed by  
This installation procedure assumes that you  
know how to navigate through the menu system  
on the DC230LP Control Panel. Refer to the  
quick reference card, Using the Menu System,  
(701P96834) for assistance.  
IP Address  
(your entry)  
>
.
System Admin  
>
f) Press [Enter].  
displays.  
5.  
RARP Setup:  
Note: If you used a static IP Address, leave the  
3.  
Access the TCP/IP menus:  
RARP setting at Disabled.  
1.  
Connect the DC230LP to your network  
outlet or cable.  
Port Setup  
>
a) Press [ ].  
displays.  
a) To change the RARP setting, press  
[ ] until the current setting displays  
Network Setup  
>
b) Press [ ] until  
RARP  
>
.
(current entry)  
displays.  
TCP/IP  
>
c) Press [ ].  
displays.  
Over  
For assistance, contact your local Xerox Customer Support Center:  
USA: 1-800-821-2797 Canada: 1-800-939-3769  
Page 1 of 4  
7+(ꢀ'2&80(17ꢀ&203$1<  
ꢀꢁꢂꢃꢀ  
DC230LP Windows NT® 4.0 TCP/IP Quick Install  
f) Press [Enter]. **SAVED**displays  
d) Press [ ] repeatedly to delete the  
momentarily, followed by  
13.  
At the client, install print drivers and map  
the printer in the usual manner. Refer to  
the CentreWare® manual, Getting Started  
with Print and Fax Services, for additional  
information.  
current entry.  
Enablement  
>
.
Enabled  
e) Use the [ ] or [ ] key to select the  
Note: The next menu at this level, Port Setting,  
has a fixed setting for the LPD (515) and can not  
be changed.  
first character in the Printer Name.  
f) Press [ ] to move to the next charac-  
ter. Repeat this procedure to enter the  
entire Printer Name.  
14.  
TCP/IP protocol and TCP/IP print services  
must be installed on the NT Server and the  
printer name must be set to [lp] (lower  
case) when configuring the LPR port.  
Refer to the screen sample below.  
11.  
Save all settings:  
Reset Required  
g) Press [Enter]. **SAVED**displays  
a) Press [Online].  
Press ENTER key  
momentarily, followed by  
displays.  
Printer Name  
(your entry)  
>
Additional information on the Windows NT  
TCP/IP setup can be found in the DC230LP  
System Administration Guide, Network Installa-  
tion and Troubleshooting.  
.
Warming Up  
Please Wait . . .  
>
b) Press [Enter].  
10.  
Enable the Line Printer Daemon (LPD):  
displays. The DC230LP will reboot,  
save the settings entered, and print a  
Configuration Report in approximately  
3 minutes.  
a) Press [Escape] to move back a level  
in the menu system.  
TCP/IP-  
>
displays.  
12.  
Check the settings on the Configuration  
Report against those entered to be sure  
they are correct.  
Line Printer  
Daemon  
>
b) Press [ ] until  
displays.  
Enablement  
(current entry)  
>
c) Press [ ].  
displays.  
Enablement  
(current entry)  
=
*
d) Press [ ].  
displays.  
Enablement  
Enabled  
=
e) Press [ ] until  
displays.  
Page 3 of 4  
7+(ꢀ'2&80(17ꢀ&203$1<  
ꢀꢁꢂꢃꢀ  
DC230LP Windows NT® 4.0 TCP/IP Quick Install  
©1998 Xerox Corporation  
701P98454 Version 1.0, 5-98  
Page 4 of 4  

Sharp Ar Bc320 User Manual
Sanyo Uf 511 User Manual
Samsung Aq09a2md User Manual
Panasonic Panafax Uf 8000 User Manual
MIELE G 6105 User Manual
LG 65UH7J User Manual
LENOVO Z510 2 User Manual
LENOVO Z90A40 User Manual
CRAFTSMAN 917.271110 User Manual
CRAFTSMAN 315.108330 User Manual