Projector
CP-CX251N
User's Manual (concise)
Thank you for purchasing this projector.
Please read through this manual before using this product, in order to use safely
and utilize well the product.
WARNING ►Before using this product, be sure to read all manuals for this
product. See the “Using the CD manual” ( 17) to read the manuals in the CD.
After reading them, store them in a safe place for future reference.
►Heed all the warnings and cautions in the manuals or on the product.
►Follow all the instructions in the manuals or on the product.
NOTE • In this manual, unless any comments are accompanied, “the
manuals” means all the documents provided with this product, and “the product”
means this projector and all the accessories came with the projector.
Contents
First of all............................................ 2 Adjusting the projector's elevator ..... 10
Entries and graphical symbols explanation......2
Displaying the picture....................... 11
Turning off the power........................ 12
Important safety instruction ..............................2
Regulatory notices.............................. 3 Replacing the lamp........................... 13
About Electro-Magnetic Interference................
3
Cleaning and replacing the air filter.. 15
Replacing the internal clock battery.. 16
About Waste Electrical and Electronic Equipment...4
Contents of package........................... 4 Using the CD manual ....................... 17
Arrangement....................................... 5 Specifications ................................... 18
Connecting with your devices............. 6 Troubleshooting
Connecting power supply................... 7
Preparing for the remote control......... 8
Turning on the power.......................... 9
- Warranty and after-service........... 19
1
Regulatory notices
About Electro-Magnetic Interference
In CANADA
CAN ICES-3(B) / NMB-3(B).
In the US, and other places where the FCC regulations are applicable
Declaration of Conformity
Trade name
HITACHI
Model Number
CP-CX251N
Responsible Party Hitachi America, Ltd.
Address 2420 Fenton Street, Suite 200 Chula Vista, CA 91914
U.S.A.
Telephone Number +1 -800-448-2244
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INSTRUCTIONS TO USERS: This equipment complies with the requirements of
FCC (Federal Communication Commission) equipment provided that the following
conditions are met. Some cables have to be used with the core set. Use the
accessory cable or a designated-type cable for the connection. For cables that
have a core only at one end, connect the core to the projector.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
3
Regulatory notices (continued)
About Waste Electrical and Electronic Equipment
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries or accumulators included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a
heavy metal content of more than 0.0005% Mercury or more than, 0.002%
Cadmium, or more than 0.004% Lead.
Contents of package
VIDEO COMPUTER MY SOURCE/
DOC.CAMERA
(1)
ASPECT
MAGNIFY
AUTO SEARCH BLANK
FREEZE
(4)
Your projector should come with the items
shown below. Check that all the items are
included. Require of your dealer immediately if
any items are missing.
PAGE
UP
VOLUME
ON
＋
OFF
DOWN
ー
MY BUTTON
KEYSTONE
1
2
MUTE
POSITION
MENU
ENTER
ESC
RESET
(1) Remote control with the two AA batteries
(2) Power cord
(3) Computer cable
(4) Lens cover and Strap
(5) User’s manuals (Book x1, CD x1)
(6) Security label
(5)
(6)
(2)
(3)
WARNING ►Do not attempt to install the projector yourself. Have your
dealer or service center handle all installation work. Note that manufacturer will
accept no liability whatsoever for accidents or injuries resulting from an incorrect
installation or improper use.
NOTE • Keep the original packing materials for future reshipment. Be sure
to use the original packing materials when moving the projector. Use special
caution for the lens.
4
Arrangement
Refer to table T-1 and figures F-1 and F-2 at the end of this manual to determine the
screen size and projection distance.
The values shown in the table are calculated for a full size screen.
a
V Screen size (vertical) H Screen size (horizontal)
Projection distance (±8%)
b1
2
, b Screen height (±8%)
• For the case of installation in a special state such as ceiling mount, the specified
mounting accessories ( 18) and service may be required. Before installing the
projector, consult your dealer about your installation.
• The screen position may shift after installation if the projector is suspended from the
ceiling or other location due to the flexibility of the plastic projector body. If readjustment is
necessary, consult with your dealer or service personnel.
• The projected image position and/or focus may change during warm-up (approx. 30
minutes after the lamp is turned on) or when the ambient conditions change. Readjust
the image position and/or focus as necessary.
• Since the projector features a short throw, be aware that it is required to select a screen
carefully to have better performance.
- A soft screen such as a pull-down screen may cause serious distortion of a projected
image. A hard screen such as a board screen is recommended for use with this projector.
- A high-gain screen such as a bead screen that has narrow viewing angle is not suitable
for this projector. A low-gain screen (around 1.0) such as a matte screen that has wide
viewing angle is recommended for use with this projector.
-
A screen with a weave pattern may cause moiré on the projected image, which is not a failure
of the projector. A screen that has less moiré effects is recommended for use with this projector.
WARNING ►Install the projector in a stable horizontal position.
►Place the projector in a cool place, and ensure that there is sufficient ventilation.
Keep a space of 30 cm or more between the sides of the projector and other objects
such as walls. Do not place or attach anything that would block the lens or vent
holes. Do not place the projector where the air from an air conditioner or similar unit
will blow on it directly.
►Do not place the projector anyplace where it may get wet.
►
Use only the mounting accessories the manufacturer specified, and leave installing
and removing the projector with the mounting accessories to the service personnel.
►Read and keep the user's manual of the mounting accessories used.
CAUTION ►Avoid placing the projector in smoky, humid or dusty place.
►Position the projector to prevent light from directly hitting the projector’s remote sensor.
►If the projector is used at an altitude of about 1600 m or higher, set ALTITUDE of
the SERVICE item in the OPTION menu to HIGH. Otherwise, set it to NORMAL.
If the projector is used with a wrong setting, it may cause damage to the projector
itself or the parts inside.
•
The projector may make a rattling sound when tilted, moved or shaken,
NOTE
since a flap to control the air flow inside of the projector has moved. Be aware that
this is not a failure or malfunction.
5
Connecting with your devices
Be sure to read the manuals for devices before connecting them to the projector.
Make sure that all the devices are suitable to be connected with this product, and
prepare the cables required to connect. Refer to figures F-3 to F-5 at the back of
this manual.
For details, please see “User's Manual” - “Operating Guide” and “Network Guide”.
• When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in
COMPUTER IN of the INPUT menu, that port will accept component video signals.
• To use network functions of the projector, connect the LAN port with the
computer's LAN port, or with an access point that is connected to the computer
with wireless LAN, using a LAN cable.
WARNING ►Use only the appropriate accessories. Otherwise it could
cause a fire or damage to the device and the projector.
- Use only the accessories specified or recommended by the projector’s
manufacturer. Consult your dealer when the required accessory did not come
with the product or the accessory is damaged. It may be regulated under some
standard.
- For a cable with a core at only one end, connect the end with the core to the
projector. That may be required by EMI regulations.
- Neither disassemble nor modify the projector and the accessories.
- Do not use the damaged accessory. Be careful not to damage the
accessories. Route a cable so that it is neither stepped on nor pinched out.
CAUTION ►For a cable with a core at only one end, connect the end with
the core to the projector. That may be required by EMI regulations.
►Do not turn on or off the projector while connected to a device in operation,
unless that is directed in the manual of the device.
►Be careful not to mistakenly connect a connector to a wrong port.
►Before connecting the projector to a network, be sure to obtain the consent of
the administrator of the network.
►Do not connect the LAN port to any network that might have the excessive
voltage.
NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input
ports of the projector are recessed.
NOTE • The COMPUTER IN1/2 port can support a component signal also. The
specific adapter or the specific cable is required for a component video input to the
projector.
6
Connecting power supply
Put the connector of the power cord into
the AC (AC inlet) of the projector.
1.
Firmly plug the power cord’s plug into
2.
the outlet. In a couple of seconds
after the power supply connection, the
POWER indicator will light up in steady
orange.
AC
Power cord
Please remember that when the DIRECT POWER ON
function activated, the connection of the power supply make the projector turn on.
WARNING ►Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in fire and/or electrical shock.
• Do not touch the power cord with a wet hand.
• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one. Never modify the power cord.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.
• Do not distribute the power supply to multiple devices. Doing so may overload
the outlet and connectors, loosen the connection, or result in fire, electric shock
or other accidents.
NOTICE ►This product is also designed for IT power systems with a phase-
to-phase voltage of 220 to 240 V.
7
Preparing for the remote control
Please insert the batteries into the remote control before using it. If the remote
control starts to malfunction, try to replace the batteries. If you will not use the
remote control for long period, remove the batteries from the remote control and
store them in a safe place.
1. Remove the battery cover.
Align and insert the two AA batteries
2.
(HITACHI MAXELL, Part No.LR6 or R6P) according
to their plus and minus terminals as indicated in
the remote control.
3. Put the battery cover back to the former state.
Remote sensor
NOTE
• Try changing the batteries when the remote
control malfunctions.
• This remote control works with the remote
sensors on the projector using infrared light
(Class 1 LED). The active sensor senses
the remote control signal assigned within 60
degrees to right and left, and within 3 meters.
For details, see User's Manual - Operating
Guide.
30°
30°
3m
(approx.)
• Prevent the remote sensors from being hit by
a strong ray. It may cause malfunction of the
projector and remote control.
WARNING ►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage,
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.
•
Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
•
•
Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.
If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
•
Obey the local laws on disposing the battery.
8
Turning on the power
Make sure that the power cord is
firmly and correctly connected to the
projector and the outlet.
Make sure that the POWER indicator is
steady orange. Then, remove the lens
cover.
Press the button on the
projector or STANDBY/ON button on
the remote control.
.
STANDBY/ON button
1
POWER indicator
.
2
3
.
CE/
ERA
MY SOUR
DOC.CM
The projection lamp will light up
and the POWER indicator will begin
blinking in green. When the power is
completely on, the indicator will stop
blinking and light in steady green.
NK
BLA
M
E
SEARCH
＋
VOLUM
AUTO
PAGEUP
PECT
ー
FREEZE
MAGNIFY
ON
DOWN
MUTE
2
OFF
MY BUTTON
1
KEYSTONE
MENU
ON
POSITI
ENTER
RESET
ESC
WARNING ►A strong light is emitted when the projector’s power is on. Do
not look into the lens of the projector or look inside of the projector through any
of the projector’s openings, since the projection ray may cause a trouble on
your eyes.
NOTE • Please power on the projector prior to the connected devices.
The projector has the DIRECT POWER ON function, which can make the projector
•
automatically turn on. For details, please see User's Manual - Operating Guide.
9
Adjusting the projector's elevator
The projector has Front foot for inclinations and Rear foot for horizontals. A spacer
is installed on the Rear elevator foot at the time of shipment, and the projector
is ready for use. If necessary, detach the spacer, and the elevator feet can be
manually twisted to make more precise adjustments.
0~2°
Front foot
Rear foot
Front foot
-1~1°
Spacer
Spacer
Rear foot
WARNING ►Keep the spacer away from children and pets. Be careful not
to let them swallow the spacer. If swallowed consult a physician immediately for
emergency treatment.
NOTE • The Front foot can be adjusted within 0~2°, while the Rear foot can
be adjusted within -1~1°.
•
After the foot is adjusted, it is possible to return it to the state of the shipment with a spacer.
It is recommended to keep the spacer and reuse it when relocating the projector.
10
Displaying the picture
VIDEO COMPUTER MY SOURCE/
DOC.CAMERA
Activate your signal source. Turn the signal
1.
ASPECT
AUTO SEARCH
BLANK
VOLUME
MAGNIFY FREEZE
ON
PAGE
UP
source on, and make it send the signal to
the projector.
＋
VOLUME+ button
VOLUME- button
MUTE button
OFF
DOWN
ー
MY BUTTON
KEYSTONE
2
MUTE
1
Press the INPUT button on the projector.
2.
POSITION
MENU
Each time you press the button, the
ENTER
projector switches its input port in turn.
You can also use the remote control to
select an input signal.
ESC
RESET
Press the VIDEO button for selecting an
input signal from the HDMI, S-VIDEO or
VIDEO port, or the COMPUTER button
for selecting an input signal from the
COMPUTER IN1 or COMPUTER IN2 port.
Use the VOLUME + / VOLUME - buttons
to adjust the volume.
To have the projector silent, press the
INPUT
button
3.
VIDEO button
MUTE button on the remote control.
VIDEO COMPUTER MY SOURCE/
DOC.CAMERA
Press the ASPECT button on the remote
4.
ASPECT
AUTO SEARCH
BLANK
VOLUME
COMPUTER button
ASPECT button
MAGNIFY FREEZE
ON
PAGE
UP
＋
control. Each time you press the button,
the projector switches the mode for aspect
ratio in turn.
OFF
DOWN
ー
MY BUTTON
KEYSTONE
2
MUTE
1
POSITION
MENU
Use the FOCUS ring to focus the picture.
5.
ENTER
ESC
RESET
FOCUS ring
WARNING ►If you wish to have a blank screen while the projector's lamp
is on, use the BLANK function. (see User’s Manual - Operating Guide)
Taking any other action may cause the damage on the projector.
Blocking the beam by something causes high temperature and could result in
fire or smoke.
(continued on next page)
11
Displaying the picture (continued)
NOTE • The ASPECT button does not work when no proper signal is inputted.
• For the details of how to adjust the picture, please see User’s Manual -
Operating Guide.
• There may be some noise and/or the screen may flicker for a moment when
an operation is made. This is not a malfunction.
Turning off the power
STANDBY/ON button
Press STANDBY/ON button on the
1.
projector or on the remote control. The
message “Power off?” will appear on the
screen for about 5 seconds.
POWER indicator
Press the STANDBY/ON button again
while the message appears.
2.
The projector lamp will go off, and the
POWER indicator will begin blinking in
orange. Then the POWER indicator will
stop blinking and light in steady orange
when the lamp cooling is complete.
E/
AMERA
M
Y
S
O
U
R
C
DOC.C
NK
BLA
P
SEARCH
＋
VOLUME
AUTO
PAGEUP
PECT
ー
FREEZE
MAGNIFY
ON
DOWN
MUTE
2
OFF
MY BUTTON
1
KEYSTONE
MENU
ITION
POS
ENTER
RESET
ESC
Attach the lens cover, after the POWER
indicator turns in steady orange.
3.
Do not turn the projector on for about 10 minutes or more after turning it off.
Also, do not turn the projector off shortly after turning it on. Such operations might
cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.
WARNING ►Do not touch around the lamp cover and the exhaust vents
during use or just after use, since it is too hot.
►Remove the power cord for complete separation. The power outlet should be
close to the projector and easily accessible.
NOTE • Please power off the projector after any connected devices are
powered off.
• This projector has the AUTO POWER OFF function that can make the
projector turn off automatically. For details, see User’s Manual - Operating
Guide.
12
Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time could cause
the pictures darker or the color tone poor. Note that each lamp has a different
lifetime, and some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare
a new lamp, make contact with your dealer and tell the lamp type number.
Type number: DT01511
Lamp cover
Turn the projector off, and unplug the power cord.
1.
Allow the projector to cool for at least 45 minutes.
Prepare a new lamp. If the projector is mounted
2.
on a ceiling, or if the lamp has broken, also ask
the dealer to replace the lamp.
In case of replacement by yourself, follow the
following procedure.
Loosen the screw (marked by arrow) of the lamp
3.
cover and then slide and lift the lamp cover to the
side to remove it.
Loosen the 2 screws (marked by arrow) of the
4.
lamp, and slowly pick up the lamp by the handle.
Never loosen any other screws.
Insert the new lamp, and retighten firmly the
5.
2 screws of the lamp that are loosened in the
previous process to lock it in place.
While putting the interlocking parts of the lamp
6.
cover and the projector together, slide the lamp
cover back in place. Then firmly fasten the screw
of the lamp cover.
Turn the projector on and reset the lamp time
7.
using the LAMP TIME item in the SETUP menu.
(1) Press the MENU button to display a menu.
(2) Point at the ADVANCED MENU in the menu using
the ▼/▲ button, then press the ► button.
(3) Point at the SETUP in the left column of the menu
Handle
using the ▼/▲button, then press the ► button.
(4) Point at the LAMP TIME using the ▼/▲ button, then
press the ► button. A dialog will appear.
(5) Press the ► button to select “OK” on the dialog. It performs resetting the lamp
time.
CAUTION ►Do not touch any inner space of the projector, while the lamp
is taken out.
NOTE • Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
13
Replacing the lamp (continued)
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp
can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or
worn over time. Note that each lamp has a different lifetime, and some may burst or
burn out soon after you start using them. In addition, if the bulb bursts, it is possible
for shards of glass to fly into the lamp housing, and for gas containing mercury and
dust containing fine particles of glass to escape from the projector’s vent holes.
►About disposal of a lamp: This product contains a mercury lamp; do not put
it in a trash. Dispose of it in accordance with environmental laws.
• For lamp recycling, go to www.lamprecycle.org (in the US).
• For product disposal, consult your local government agency
For more information, ask your dealer.
• If the lamp should break (it will make a loud bang when it does),
unplug the power cord from the outlet, and make sure to request a
replacement lamp from your local dealer. Note that shards of glass
could damage the projector’s internals, or cause injury during handling,
so please do not try to clean the projector or replace the lamp yourself.
• If the lamp should break (it will make a loud bang when it does), ventilate the
room well, and make sure not to inhale the gas or fine particles that come out
from the projector's vent holes, and not to get them into your eyes or mouth.
Disconnect
the plug
from the
power
• Before replacing the lamp, turn the projector off and unplug the power
outlet
cord, then wait at least 45 minutes for the lamp to cool sufficiently.
Handling the lamp while hot can cause burns, as well as damaging the lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
•
Do not open the lamp cover while the projector is suspended from a ceiling.
This is dangerous, since if the lamp’s bulb has broken, the shards will fall out
when the cover is opened. In addition, working in high places is dangerous, so
ask your local dealer to have the lamp replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose
screws could result in damage or injury.
• Use only the lamp of the specified type. Use of a lamp that does not
meet the lamp specifications for this model could cause a fire, damage or
shorten the life of this product.
• If the lamp breaks soon after the first time it is used, it is possible
that there are electrical problems elsewhere besides the lamp. If this
happens, consult your local dealer or a service representative.
•
Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• Using the lamp for long periods of time, could cause it dark, not to light
up or to burst. When the pictures appear dark, or when the color tone
is poor, please replace the lamp as soon as possible. Do not use old
(used) lamps; this is a cause of breakage.
14
Cleaning and replacing the air filter
The air filter has two kinds of filters inside. Please check and clean the air filter periodically.
When the indicators or a message prompts you to clean the air filter, comply with it as soon
as possible. If the filters are damaged or heavily soiled, replace them with the new ones. To
prepare the new filters, make contact with your dealer and tell the following type number.
Type number : UX37191 (Filter set)
When you replace the lamp, please replace the air filter. An air filter of specified type will
come together with a replacement lamp for this projector.
3.
Turn the projector off, and unplug the power cord. Allow
the projector to sufficiently cool down.
1.
Use a vacuum cleaner on and around the filter cover.
2.
Slide the filter unit upward to take it off from the projector.
Use a vacuum cleaner for the filter vent of the projector.
Filter cover
3.
4.
5.
Take the fine meshed filter out while holding the filter
cover. It is recommended to leave the coarse meshed
filter in the filter cover as it is.
Intake vent
Filter unit
Use a vacuum cleaner on both sides of the fine meshed
filter while holding it so it will not be sucked in. Use a
vacuum cleaner for the inside of the filter cover to clean
up the coarse meshed filter. If the filters are damaged
or heavily soiled, replace them with new ones.
6.
Filter cover
7.
Put the fine meshed filter on the coarse meshed one,
turning its plastic band side up.
7.
Filter
(coarse meshed)
Filter (fine meshed)
Put the filter unit back into the projector.
8.
9.
Turn the projector on and reset the filter time using the
FILTER TIME item in the EASY MENU.
(1) Press the MENU button to display a menu.
(2) Point at the FILTER TIME using the ▼/▲ button, then
press the ► button. A dialog will appear.
Plastic
band
(3) Press the ► button to select “OK” on the dialog. It performs resetting the filter time.
WARNING ►Before taking care of the air filter, make sure the power cable
is not plugged in, then allow the projector to cool sufficiently.
►
Use only the air filter of the specified type. Do not use the projector without the
air filter or the filter cover. It could result in a fire or malfunction to the projector
Clean the air filter periodically. If the air filter becomes clogged by dust or the like,
.
►
internal temperatures rise and could cause a fire, a burn or malfunction to the projector.
NOTE • Please reset the filter time only when you have cleaned or replaced
the air filter, for a suitable indication about the air filter.
• The projector may display the message such as “CHECK THE AIR FLOW” or
turn off the projector, to prevent the internal heat level rising.
15
Replacing the internal clock battery
Installing the battery is required in some cases. ( Event Scheduling in the User's
Manual - Network Guide) A battery is not contained at the time of factory shipment.
Please replace a battery according to the following procedure.
Battery Cover
Turn the projector off, and unplug the power cord.
Allow the projector to cool sufficiently.
1.
After making sure that the projector has cooled
adequately, slowly turn over the projector, so that
the bottom is facing.
2.
Turn the battery cover fully in the direction indicated
“OPEN” using a coin or the like, and pick the cover
up to remove it..
3.
90°
N
CLOSE
Pry up the battery using a flathead screwdriver or
4. .the like to take it out. While prying it up, put a finger
lightly on the battery since it may pop out of the
holder.
OPEN
CLOSE
Replace the battery with a new HITACHI MAXELL,
Part No.CR2032 or CR2032H.
Slide the battery in under the plastic claw, and push
it into the holder until it clicks.
5.
6.
OPEN
CLOSE
.Replace the battery cover in place, then turn it
in the direction indicated “CLOSE” using such as
coins, to fix.
90°
WARNING
►Always handle the batteries with care and use them only as
directed. Battery may explode if mistreated. Do not recharge, disassemble or
dispose of in fire.
And also improper use may result in cracking or leakage, which could result in
fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified.
• Make sure the plus and minus terminals are correctly aligned when loading a
battery.
• Keep a battery away from children and pets. If swallowed consult a physician
immediately for emergency treatment.
• Do not short circuit or solder a battery.
• Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry
place.
• If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing a battery.
16
Using the CD manual
The other manuals for this product are written into the included CD-ROM titled
“User’s Manual (detailed)”. Before using the CD-ROM, please read the following
to ensure the proper use.
System requirements
The system for using the CD-ROM requires the following.
Windows®:
OS:Microsoft®
Windows® XP, Windows Vista® or later
Macintosh®:
OS:Mac OS® 10.2 or later
CD-ROM/DVD-ROM drive:
Applications:
Microsoft® Internet Explorer®6.0 or later
Adobe® Acrobat® Reader® 8.0 or later
How to use the CD
1. Insert CD into computer’s CD-ROM/DVD-ROM drive.
Windows®:
In a while, Web browser automatically starts. Start up
window comes up.
(1) Double-click on the “PROJECTORS” icon appeared on
the desktop screen.
Macintosh®:
(2) When “main.html” file is clicked, Web browser will start
and Initial window will appear.
2. Click the model name of your projector first, and then click language you want
from the displayed list. The User’s manual (detailed) will open.
CAUTION ►Only use the CD-ROM in a computer CD/DVD drive. The
CD-ROM is designed for computer use only. NEVER INSERT THE CD-ROM
INTO A NON-COMPUTER CD/DVD PLAYER! Inserting the CD-ROM into an
incompatible CD/DVD drive may produce a loud noise, which in turn MAY
RESULT IN EAR AND SPEAKER DAMAGE!
• After using CD-ROM, please put it into CD case and keep it. Please keep
the CD neither in direct sunlight nor in a high temperature and high humidity
environment.
NOTE • The information in the CD-ROM is subject to change without notice.
• No responsibility is taken for any obstacle and defect to hardware and software
of your computer as a result of the use of the CD-ROM.
• All or Any part of the information in the CD-ROM must not be copied,
reproduced or republished without notice to our company.
17
Specifications
Item
Specification
Product name
Liquid Crystal Panel
Lamp
Liquid crystal projector
786,432 pixels (1024 horizontal x 768 vertical)
225W UHP
Speaker
1W
Power supply
Power consumption
AC 100-120V/3.1A, AC 220-240V/1.5A
AC 100-120V: 300W, AC 220-240V:290W
0 ~ 40°C (Operating)
35 ~ 40°C (The brightness of the lamp is reduced automatically.)
Temperature range
345 (W) x 85 (H) x 303 (D) mm
Size
* Not including protruding parts.
Refer to figure F-6 at the back of this manual.
Weight (mass)
approx. 3.4 kg
Computer input port
HDMI input port
COMPUTER IN1
HDMI ................ HDMI connector ×1
....................... D-sub 15 pin mini x1 Audio input/output port
COMPUTER IN2/MONITOR OUT
AUDIO IN (R, L) ................... RCA x2
Ports
....................... D-sub 15 pin mini x1 AUDIO OUT (R, L) ............... RCA x2
Video input port
Others
S-VIDEO ..............mini DIN 4 pin x1 USB TYPE B .....................USB-Bx1
VIDEO.................................RCA x1 CONTROL................. D-sub 9 pin x1
LAN..................................... RJ45 x1
Lamp: DT01511
Filter set: UX37191
Mounting accessary: HAS-AW100 (Bracket for ceiling mount)
HAS-203L (Fixing adaptor for low ceilings)
HAS-P100 (Fixing adaptor for high ceilings)
* For more information, please consult your dealer.
Optional parts
18
Troubleshooting - Warranty and after-service
If an abnormal operation (such as smoke, strange odor or excessive sound)
should occur, stop using the projector immediately.
Otherwise if a problem occurs with the projector, first refer to “Troubleshooting” of
“Operating Guide” and “Network Guide”, and run through the suggested checks.
If this does not resolve the problem, please consult your dealer or service
company. They will tell you what warranty condition is applied.
Please check the following web address where you may find the latest information
for this projector.
Product
information and
Manuals :
Production
information :
Direct link to
manual download :
userguides.htm
NOTE • The information in this manual is subject to change without notice.
• The illustrations in this manual are for illustrative purposes. They may differ
slightly from your projector.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
Trademark acknowledgment
• Mac®, Macintosh® and Mac OS® are registered trademarks of Apple Inc.
• Adobe® and Acrobat®, Reader® are registered trademarks of Adobe Systems
Incorporated.
• Microsoft®, Internet explorer®, Windows®, and Windows Vista® are registered trademarks
of Microsoft Corporation in the U.S. and/or other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
• Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc Association.
All other trademarks are the properties of their respective owners.
End User License Agreement for the Projector Software
• Software in the projector consists of the plural number of independent software
modules and there exist our copyright or/and third party copyrights for each of
such software modules.
• Be sure to read “End User License Agreement for the Projector Software”
which is separated document. (in the CD)
19
20
|