PARTYBOX 200
PARTYBOX 300
OWNER’S MANUAL
co-channel mobile satellite systems; (ii) the maximum antenna
gain permitted for devices in the bands 5250-5350 MHz and
5470-5725 MHz shall comply with the e.i.r.p. Limit: and (iii)
The maximum antenna gain permitted for devices in the band
5725-5825 MHz shall comply with the e.i.r.p. Limits specified for
point-to-point and non-point-to-point operation as appropriate.
(iv) Users should also be advised that high-power radars are
allocated as primary users (i.e. priority users) of the bands 5250-
5350 MHz and 5650-5850 MHz and that these radars could
cause interference and/or damage to LE-LAN devices.
FOR ALL EU COUNTRIES
For products that include audio out
Prevention of hearing loss
Caution: Permanent hearing loss may occur
if earphones or headphones are used at high
volume for prolonged periods of time.
For France, the products have been tested to
comply with Sound Pressure Level requirement
laid down in the applicable NF EN 50332 L.5232-1.
Note:
Exposure of humans to RF fields (RSS-102)
–
To prevent possible hearing damage, do not listen to high volume
levels for long periods.
The computers employ low gain integral antennas that do not
emit RF field in excess of Health Canada limits for the general
population; consult Safety Code 6, obtainable from Health
The radiated energy from the antennas connected to the wireless
adapters conforms to the IC limit of the RF exposure requirement
regarding IC RSS-102, Issue 5 clause 4. SAR tests are conducted
using recommended operating positions accepted by the FCC/
RSS with the device transmitting at its highest away from the
body. Non-compliance with the above restrictions may result in
a violation of FCC RF exposure guidelines.
WEEE Notice
The Directive on Waste Electrical Equipment (WEEE), which
entered into force as European law on 14/02/2014, resulted in
a major change in the treatment of electrical equipment at end-
of-life.
The purpose of this Directive is, a first priority, the prevention of
WEEE, and in addition, to promote the reuse, recycling and other
forms of recovery of such wastes as so as to reduce disposal.
The WEEE logo on the product or on its box indicating collection
for electrical and electronic equipment consists of the crossed-
out wheeled bin, as shown below.
Use Restriction: Attention in France, the operation is limited to
indoor use within the band 5150-5350 Mhz.
For Products with Radio Receivers That Can
Use an External Antenna (USA ONLY)
This product must not be disposed of or dumped with
your other household waste. You are liable to dispose
of all your electronic or electrical waste equipment by
relocating over to the specified collection point for
recycling of such hazardous waste. Isolated collection
and proper recovery of your electronic and electrical waste
equipment at the time of disposal will allow us to help conserving
natural resources. Moreover, proper recycling, and collection
points, please contact your local city center, household waste
disposal service, shop from where you purchased the equipment,
or manufacturer of the equipment.
CATV (Cable TV) or Antenna Grounding
If an outside antenna or cable system is connected to this
product, be certain that it is grounded so as to provide some
protection against voltage surges and static charges. Section
810 of the National Electrical Code (NEC), ANSI/NFPA No. 700-
1984, provides information with respect to proper grounding of
the mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes
and requirements of the electrode.
RoHS Compliance
This product is in compliance with Directive 2011/65/EU of the
European Parliament and of the Council of 8 June 2011 on the
restriction of the use of certain hazardous substances in electrical
and electronic equipment.
Note to CATV System Installer
This reminder is provided to call the CATV(cable TV) system
installer’s attention to article 820-40 of the NEC, which provides
guidelines for proper grounding and, in particular, as close to the
point of cable entry as possible.
For Products that includes Batteries
Caution: This product uses a laser system. To prevent direct
exposure to the laser, do not open the cabinet enclosure or defeat
any of the safety mechanisms provided for your protection. Do
NOT START INTO THE LASER BEAM. To ensure proper use of
this product, please read the owner’s manual carefully and retain
it for future use. Should the unit require maintenance or repair,
please contact your local JBL service. Refer servicing to qualified
personnel only.
EU Batteries Directive 2013/56/EU
A new battery directive 2013/56/eu on Battery and Accumulator
replacing directive entered into force on the 01/07/2015. The
directive applies to all types of batteries and accumulator
(AA, AAA, button cells, rechargeable packs) including those
incorporated into appliances except for military, medical
and power tool applications. The directive sets out rules for
collection, treatment, recycling and disposal of batteries, and
aims to prohibit certain hazardous substances and to improve
environmental performance of batteries and all operators in the
supply chain.
3
www.jbl.com
Instructions for Users on Removal, Recycling and Disposal
of Batteries
EPILEPSY
WARNING
A few people may experience epileptic
seizures when viewing flashing lights.
The remove the batteries from your equipment or remote control,
reverse the procedure described in the owner’s manual for
inserting batteries. For products with a built-in battery that lasts
for the lifetime of the product, removal may not be possible for
the user. In this case, recycling or recovery, it becomes necessary
to replace such a battery, this procedure must be performed by
authorized services centers. In the European Union and other
locations, it is illegal to dispose of any battery with household
trash. All batteries must be disposed of in an environmentally
sound manner. Contact your local waste-management officials
for information regarding the environmentally sound collection,
recycling and disposal of used batteries.
WARNING: Danger of explosion if battery is incorrectly replaced.
To reduce risk of fire or burns, don’t disassemble, crush,
puncture, short external contact, expose to temperature above
60°C (140°F), or dispose of in fire or water. Replace only with
specified batteries. The symbol indicating ‘separate collection’
for all batteries and accumulators shall be crossed-out wheeled
bin shown below:
In case of batteries, accumulators and button cells containing
more than 0.0005 mercury, more than 0.002% cadmium or more
than 0.004% lead, shall be marked with the chemical symbol for
the metal concerned: Hg,Cd or Pb respectively. Please Refer to
the below symbol:
WARNING: DO NOT INGEST BATTERIES, CHEMICAL BURN
HAZARD [the remote supplied with] This product contains a coin/
button cell battery. If the coin/button cell battery is swallowed, it
can cause severe international burns in just 2 hours and can lead
to death. Keep new and used batteries away from children. If you
think batteries might have been swallowed or placed inside any
part of body, seek immediate medical attention.
For All Products Except Those with Wireless
Operation
HARMAN International hereby declares that this equipment is in
compliance with EMC 2014/30/EU Directive, LVD 2014/35/EU
Directive. The declaration of conformity may be consulted in the
For All Products with Wireless Operation
HARMAN International hereby declares that this equipment
is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU. The declaration of
conformity may be consulted in the support section of our Web
4
TABLE OF CONTENTS
7. USING YOUR PARTYBOX
9
IMPORTANT SAFETY INSTRUCTIONS
2
7.1 BLUETOOTH CONNECTION
9
FEDERAL COMMUNICATION COMMISSION
INTERFERENCE STATEMENT
2
2
3
7.2 USB CONNECTION
9
10
10
11
11
FOR PRODUCTS THAT TRANSMIT RF ENERGY
7.3 AUX CONNECTION
EXPOSURE OF HUMANS TO RF FIELDS (RSS-102)
7.4 INPUT CONNECTION
FOR PRODUCTS WITH RADIO RECEIVERS THAT CAN
USE AN EXTERNAL ANTENNA (USA ONLY)
7.5 MIX SOUND WITH A MICROPHONE OR GUITAR
7.6 CHARGING EXTERNAL USB DEVICES
3
3
3
FOR ALL EU COUNTRIES
FOR PRODUCTS THAT INCLUDES BATTERIES
FOR ALL PRODUCTS EXCEPT THOSE WITH WIRELESS
OPERATION
8. CARRYING YOUR PARTYBOX
12
4
4
FOR ALL PRODUCTS WITH WIRELESS OPERATION
9. SETTINGS
12
9.1 TWS MODE
12
1. INTRODUCTION
6
6
9.2 DEMO MODE
12
12
9.3 STANDBY MODE
2. WHAT’S IN THE BOX
10. SPECIFICATIONS
11. TROUBLESHOOTINGS
12. COMPLIANCE
13
13
14
14
3. PRODUCT OVERVIEW
7
7
3.1 TOP PANEL
3.2 BACK PANEL
7
4. PLACEMENT
5. POWER ON
8
8
13. TRADEMARK
6. CHARGING (PARTYBOX 300 ONLY)
9
6.1 CHARGE YOUR SPEAKER
9
6.2 CHECK THE BATTERY LEVEL
9
5
www.jbl.com
1. INTRODUCTION
2. WHAT’S IN THE BOX
Congratulations on your purchase! This manual includes
information about “PARTYBOX 200” and “PARTYBOX 300”
speakers. We encourage you to take a few minutes to read this
manual, which describes the product and includes step-by-step
instructions to help you to set up and get started. Read and
understand all the safety instructions before using your product.
If you have any questions about these products, their installation
or their operation, please contact your retailer or customer
2
3
1
1) Main unit
2) Power cord*
3) DC cable
*Power cord quantity and plug type vary by regions.
6
6)
7)
3. PRODUCT OVERVIEW
3.1 Top Panel
•
•
Turn the power on or off.
(PartyBox 300 only)
Battery level indicator.
PartyBox 300
Caution:
–
Do not look directly at the light-emitting parts when the speaker
lights are turned on.
LED behavior
White (Constant)
Power on
7
1
2
Amber (Constant) Standby
6
5
Off
Power off
Pairing
White (Fast flash)
White (Constant)
Off
3
Connected
Not connected
On
4
White (Constant)
Off
Off
Red (Fast flash)
Low battery
(for PartyBox
300 only)
White (Slow flash) Charging
PartyBox 200
White (Constant)
Charged
3.2 Back Panel
10
9
1
1
2
2
3
4
5
6
6
5
3
8
7
4
1) AUX
•
Connect to an external audio device through a 3.5mm
audio cable (not supplied).
1)
2)
3)
4)
/
2) USB
•
•
•
Increase or decrease the volume level.
Play, pause or resume.
•
•
Connect to a USB storage device.
Charge an external USB device.
3) DC
•
Connect to a car charger.
Press to enhance bass or restore.
4) AC
•
Connect to AC power supply.
•
•
•
Press to toggle between different light patterns.
Press to turn Off / On, all the lights.
Press and hold for 2 seconds to turn the strobe light on
or off.
5) INPUT
Connect to the analog audio output jacks of an analog
device through RCA (red/white) audio cable (not supplied).
•
6) OUTPUT
Connect to the analog audio input jacks of an analog
device through RCA (red/white) audio cable (not supplied).
5)
•
•
•
Press to enter Bluetooth pairing mode.
Press and hold for 2 seconds to enter True Wireless
Stereo (TWS).
7) MIC
•
Press and hold for 10 seconds to forget all paired devices.
•
Connect to a microphone.
8) GUITAR
•
Connect to the guitar.
7
www.jbl.com
4. PLACEMENT
5. POWER ON
Notes:
Cautions:
–
For best quality sound, ensure the two tweeters are placed on the
upper side of the speaker box.
–
–
Use only provided power cord.
For PartyBox 300, either AC/DC power or built-in battery can be
–
Do not sit on the speaker or push it. Otherwise, it may result in
malfunction and causing personal injury and /or property damage.
used as a power supply.
1. Plug one end of the AC power cord into the power connector
on the back of the speaker, then plug the other end to a wall
outlet.
Place the speaker on a flat, stable surface and make sure that the
rubber feet side is down. You can place the speaker vertically or
horizontally. It automatically optimizes sound to adapt to placing
orientation.
a
b
2. Connect the car charger to the DC power jack of the speaker,
and then to your vehicle’s car charger outlet.
Vertical
Horizontal
8
6. CHARGING (PartyBox 300 only)
7. USING YOUR PARTYBOX
PartyBox 300 is powered by a built-in rechargeable battery.
7.1 Bluetooth Connection
Notes:
You can use your PartyBox as an external speaker for your
Bluetooth enabled smartphone or tablet.
1. Press to enter Bluetooth pairing mode.
–
Fully charge the built-in battery before using for the first time, which
will prolong the battery lifespan.
–
Built-in battery charging works on AC power only.
2. Choose “PartyBox 200” or “PartyBox 300” to connect.
6.1 Charge your Speaker
1
Use the AC power to charge your PartyBox 300.
2
Bluetooth
Bluetooth
10m (30”)
DEVICES
JBL PartyBox 300
JBL PartyBox 200
3. Once successfully connected, audio will stream from your
Bluetooth device to this speaker.
Notes:
–
–
–
–
This speaker can memorize a maximum of 8 paired devices. The
ninth paired device will replace the first one.
The operational range between this speaker and a Bluetooth device
is approximately 10 meters (30 feet).
If a PIN code is requested while connecting a Bluetooth device,
enter “0000”.
Bluetooth performance can be affected by the distance between
this product and your Bluetooth device and the environment of
operation.
6.2 Check the Battery Level
The speaker is powered by the built-in rechargeable battery.
After power-on, the speaker shows the battery level immediately,
you can check the status of the PartyBox battery by pressing
on any button.
To terminate the Bluetooth-enabled device:
•
•
•
Turn off this speaker;
Disable Bluetooth on your device; or
Move this speaker beyond the Bluetooth operational range.
To reconnect the Bluetooth-enabled device:
•
When you turn on this speaker next time, it tries to reconnect
the last connected device automatically;
•
If not, manually select “JBL PartyBox 300” or “JBL PartyBox
200” on your Bluetooth device to start a connection.
Note:
–
To exit Bluetooth mode, insert a USB storage device.
9
www.jbl.com
2. Turn on your portable audio device and it starts playing.
7.2 USB Connection
With your PartyBox, you can enjoy music that is stored on a
USB storage device such as an MP3 player.
Plug your USB storage device into the USB port of your PartyBox.
The music will play automatically. If not, please check if the USB
device contains playable audio contents.
2
1
Note:
–
To exit AUX mod, choose Bluetooth or USB as a source first.
7.4 INPUT Connection
Audio formats
Note:
–
To play music on your analog device through this speaker, make
sure that no Bluetooth connection, USB device, or AUX connection
is available.
Extension Codec
Sample rate
Bitrate
WAVE
PCM
44.1KHz ~192KHz < 5Mbps
44.1KHz ~192KHz < 5Mbps
44.1KHz ~192KHz < 5Mbps
LPCM
Connect a pair of RCA audio cables (red/white, not supplied) to:
•
IMA_
ADPCM
the RCA audio output sockets (red/white) on the analog
device (TV, DVD player, etc);
MPEG
44.1KHz ~192KHz < 5Mbps
44.1KHz ~192KHz < 5Mbps
•
the INPUT (L/R) connectors on the rear of this speaker.
MULAW
MP3
MPEG1
layer1/2/3
32KHz ~48KHz
16KHz ~24KHz
8KHz ~12KHz
≤ 320Kbps
32Kbps ~
320Kbps
MPEG2
layer1/2/3
8Kbps ~
160Kbps
MPEG2.5
layer3
8Kbps ~
160Kbps
WMA
8Kbps ~
48Kbps
AUDIO OUT
L
R
7.3 AUX Connection
.
.
.
Notes:
–
When the USB source is not playing, Bluetooth can break in and
play music from the phone.
–
–
When USB is playing, Bluetooth cannot break in USB.
Priority goes to USB, Bluetooth and then Aux.
To play music on your portable audio device through this
speaker, make sure that no Bluetooth connection or USB device
is available.
1. Connect a 3.5mm audio cable (not supplied) to:
•
•
the headphone socket of your portable audio device;
the AUX connector of this speaker.
10
7.5 Mix Sound with a Microphone or Guitar
7.6 Charging External USB Devices
By using a microphone (not supplied) or an electric guitar (not
supplied), you can mix its sound with an audio source.
You can use this speaker as a battery charger for your
rechargeable USB devices.
1. Rotate counterclockwise the MIC/GUITAR volume knob to
Connect your USB device to the USB port on the rear of this
speaker.
turn down the volume.
2. Connect your microphone or guitar to the MIC/GUITAR jack
PartyBox 300
of this speaker.
3. Sing through the microphone or play guitar.
•
•
To adjust the volume of the audio source, press
To adjust the volume of the microphone or guitar, rotate
/
;
the MIC/GUITAR volume knob.
PartyBox 200
Caution:
–
When not using the microphone or guitar, decrease the MIC/
GUITAR volume to minimum and remove them from the jack.
11
www.jbl.com
8. CARRYING YOUR PARTYBOX
9. SETTINGS
Cautions:
9.1 TWS Mode
–
Before carrying the speaker, make sure that all the cords are
disconnected.
The two PartyBox speakers can connect to each other in TWS
mode.
–
To avoid personal injury and/or property damage, hold the product
firmly while carrying.
1. Press and hold on both speakers simultaneously for 5
seconds, TWS connection will be built up. By default, the
speaker which connected to your smartphone is the master
speaker (L channel), the other one is the slave speaker (R
channel).
2. Press L/R button on one speaker to toggle between L
channel / R channel / Stereo, another speaker will change
the setting automatically.
3. In TWS mode, press and hold for 5 seconds on either
speaker or power off the speaker to exit the TWS mode.
10m (30”)
9.2 Demo Mode
Cautions:
–
If you plugged out the AC power (PartyBox 300 only), then you
plugged it in, the Demo Mode will be resumed automatically.
–
Ensure PartyBox is powered by AC to go into Demo Mode.
To enter or to exit demo mode, press and hold
simultaneously for 5 seconds.
and
In demo mode, all the input sources are disabled, all buttons but
/
/
/
are disabled.
Note:
–
The PartyBox built-in with 3 x 30 seconds music tracks.
Playback
•
•
Press once to start, pause or resume play.
Press once after the pause, to play the next track.
9.3 Standby Mode
The product will enter into sleep mode after 20 minutes without
operation.
•
If the“PartyBox” powered by the battery, it will auto power off
if no action for 20 minutes.
•
If the “PartyBox” powered by AC or DC power source, the
product will enter standby mode if no action for 20 minutes.
Press (power) or Bluetooth stream break-in in standby mode,
the speaker will enter normal mode.
12
10. SPECIFICATIONS
11. TROUBLESHOOTINGS
Product name
PartyBox 300
PartyBox 200
Caution:
–
Never try to repair the product by yourself. If you have any
problems while using this product, check the following points
before you request service.
AC power input
DC power input
Built-in battery
Power consumption
100-240V ~ 50/60Hz
12V 8A
Li-ion 10.4Ah, 7.2V N/A
60W
System
The unit will not turn on.
Standby power
consumption
<2W with BT connecting; <0.5W
without BT connecting
•
Check if the power cord is plugged into the outlet and to the
PartyBox.
USB output
5V 2.1A
•
For “PartyBox 300” make sure the speaker is fully charged,
Speaker drivers
Speaker impedance
Total output power
2 woofer + 3 tweeter
4 ohm
if not use the power cord to turn on your speaker.
Sound
120 W RMS
No sound from the PartyBox.
Signal-to-noise (S/N)
ratio
•
•
•
Make sure that the PartyBox is powered on.
Make sure that volume level is turned to an audible level.
Make sure that it is connected to a music source.
65 dBA
Frequency response
Bluetooth version
Bluetooth profile
45 Hz - 18 KHz (-6dB)
4.2
Bluetooth
A2DP, AVRCP
A device cannot connect with the PartyBox.
Bluetooth transmitter
frequency range
•
•
Check if you enable the Bluetooth function of the device.
2402 - 2480 MHz
The PartyBox is already connected to another Bluetooth
device. Press and hold on Bluetooth to disconnect and pair
with a new device.
Bluetooth maximum
transmitter power
8dBm (EIRP)
Poor audio quality from a connected Bluetooth device.
Bluetooth transmitter
modulation
•
The Bluetooth reception is poor. Move the device closer to
the PartyBox, or remove any obstacle between the device
and the PartyBox.
GFSK, π/4 DQPSK, 8DPSK
Approx. 10 m (33 feet)
FAT16, FAT32
Bluetooth range
USB format
USB file format
Input sensitivity
.mp3, .wma, .wav
•
AUX in: 500mV rms (RCA
connector); 250 mV rms
(3.5mm connector).
•
Digital input:
Bluetooth/USB -12dBFS
Dimension (W x H x D) 330 x 688 x 323 mm /
13 x 27 x 12.7 in
Net weight
15.84 kg
15.32 kg
13
www.jbl.com
12. COMPLIANCE
13. TRADEMARK
The product is in compliance with the European Union energy
legislation.
Bluetooth connection mode
The product is intended to be used for streaming music via
Bluetooth connection. A consumer can stream Bluetooth
audio to the speaker. When the product is connected through
Bluetooth, the Bluetooth connection must remain active at all
times to ensure proper operation.
The product will enter into sleep mode (networked standby),
after 20 minutes without operation, the power consumption @
sleep is less than 2.0 Watts, after which it can be re-activated
via Bluetooth connection.
Este equipamento não tem direito à proteção contra interferência
prejudicial e não pode causar interferência em sistemas
devidamente autorizados.
Este produto está homologado pela ANATEL, de acordo com
os procedimentos regulamentados pela Resolução 242/2000, e
atende aos requisitos técnicos aplicados.
Para maiores informações, consulte o site da ANATEL – www.
anatel.gov.br
Bluetooth disconnection mode
The product will enter into standby mode, after 20 minutes
without operation, the power consumption @ standby is less
than 0.5 Watts.
The Bluetooth® word mark and logos are registered trademarks
owned by the Bluetooth SIG, Inc. and any use of such marks by
HARMAN International Industries, Incorporated is under license.
Other trademarks and trade names are those of their respective
owners.
14
Торговая марка
Назначение товара
Изготовитель
:
:
:
JBL
Активная акустическая система
Харман Интернешнл Индастриз Инкорпорейтед, США, 06901 Коннектикут, г.Стэмфорд, Атлантик
Стрит 400, офис 1500
Страна происхождения
Импортер в Россию
Гарантийный период
:
:
:
Китай
OOO “ХАРМАН РУС СиАйЭс“, Россия, 127018, г.Москва, ул. Двинцев, д.12, к 1
1 год
Срок службы
:
5 лет
Товар сертифицирован
Дата производства
:
Дата изготовления устройства определяется по двум буквенным обозначениям из второй группы
символов серийного номера изделия, следующих после разделительного знака «-». Кодировка
соответствует порядку букв латинского алфавита, начиная с января 2010 года: 000000-MY0000000,
где «M» - месяц производства (А - январь, B - февраль, C - март и т.д.) и «Y» - год производства (A -
2010, B - 2011, C - 2012 и т.д.).
© 2018 HARMAN International Industries, Incorporated. All rights reserved. JBL is a trademark
of HARMAN International Industries, Incorporated, registered in the United States and/or other
countries. Features, specifications and appearance are subject to change without notice. The
Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and
any use of such marks by HARMAN International Industries, Incorporated is under license.
Other trademarks and trade names are those of their respective owners. The terms HDMI, the
HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks
of HDMI Licensing LLC in the United States and other countries. Manufactured under
license from Dolby Laboratories. Dolby, Dolby Audio, Pro Logic and the double-D symbol are
trademarks of Dolby Laboratories.
HARMAN International Industries,
Incorporated 8500 Balboa
Boulevard, Northridge, CA 91329
USA
|