MODEL #750
SANI-VAC
WARNING!
FOR YOUR SAFETY PLEASE READ INSTRUCTIONS
BEFORE OPERATING TOOL. & WEAR EYE PROTECTION
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
WARNING: The manufacturer cannot accept responsibility for damage caused when the
appliance is not used according to the instructions, or for uses other than those for which
it was intended.
To reduce the risk of fire, electric shock or injury:
·
Do not leave appliance when plugged in. Unplug from outlet when not in use and
before servicing.
·
·
WARNING! Electric shock could occur if used outdoors or on wet surfaces.
Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
·
·
Use only as described in this manual. Use only manufacturer’s recommended
attachments.
Do not use with damaged cord or plug. If appliance is not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, return it to your
retailer for service.
·
Do not pull or carry by cord, use cord as a handle, close a door on the cord, or pull
cord around sharp edges or corners. Do not run appliance over cord. Keep cord
away from heated surfaces.
·
·
·
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Do not handle plug or appliance with wet hands.
Do not put any object into openings. Do not use with any opening blocked; keep
free of dust, lint, hair and anything that may reduce air flow.
Keep hair, loose clothing, fingers and all parts of the body away from openings
and moving parts.
·
·
Do not pick up anything that is burning or smoking, such as cigarettes, matches or
hot ashes.
·
·
·
·
Do not use without vacuum bag and/or filters in place.
Turn off all controls before unplugging.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible liquids such as gasoline or use in
areas where they may be present.
·
Do not attempt to service the unit while appliance is plugged in.
SAVE THESE INSTRUCTIONS
Handlermfg.com | 750 SaniVac Instruction Manual | 2012
Replacing the filters
It is recommended the vacuum bag is changed when the full bag indicator changes color
or the suction power of the canister becomes weak.
1. Turn off the canister
2. Remove the hose and unplug it from the canister body.
3. Open the dust cover.
4. Remove the entire bag holder. DO NOT THROW IT AWAY (See Fig. 1)
5. Discard the full bag.
6. Insert a new bag by aligning the notch on the bag collar with the base of the bag
holder. (See Fig. 2)
7. Lock the bag into place under the bag holder tab.
8. Insert the bag holder by sliding the 2 prongs back into the canister body.
(See Fig. 1).
9. Replacement Filter bag 12/Set Order 750F-FB
10. Close the dust cover.
Fig. 1
Handlermfg.com | 750 SaniVac Instruction Manual | 2012
1. Replacing the secondary filter
Turn off the canister and remove the
hose. Open the dust cover. Remove the
filter from behind the bag.
(See Fig. 3)
Either shake the dust out of the filter or
wash it by hand. (Make sure the filter is
completely dry before reinstalling.)
Reinsert the filter and close the dust
cover.
Replacement Filter: Order 750PF
2. Replacing the HEPA filter
Turn off the canister and power nozzle.
Remove the hose and unplug it from the
canister body. Open the dust cover.
Remove the filter from the top of the
canister by pulling the tab on the filter
toward you. (See Fig. 4)
Discard the old filter.
Reinsert a new filter by sliding it back
into the holder. Close the dust cover.
Replacement Filter:
Order 750F-FB (Set of 12)
ONLY WHEN NECESSARY
To tighten stainless steel Sani-Vac hose, grasp the hose (not by the end fittings). Twist
firmly with right hand in this direction
, counter clockwise while twisting left in the
opposite direction clockwise . Any part, or all of the hose may be adjusted. Insert cuff
firmly into Sani-Vac opening.
DO NOT OVERWIND!
Handlermfg.com | 750 SaniVac Instruction Manual | 2012
Troubleshooting Guide
Problem
Check Point
Solution
Suction power is weak.
Vacuum bag
If bag is full, replace it.
Wand or hose
If clogged or blocked
remove the object
Vacuum does not work
Is the hose adapter inserted Insert it completely
into the vacuum
completely?
When the vacuum bag is
Unplug the vacuum and
full or if the wand or hose is check the bag, wand and
blocked, the motor thermal hose and remove any
protection is activated.
blockages. The vacuum can
be turned on again after
approximately 20 minutes
Pull the power cord out a
little and press the cord
rewind button again
Power cord does not rewind Power cord
Power cord won’t pull out
of the vacuum
Power cord
Do not pull the cord by
force. Rewind it a little by
pressing the cord rewind
button and try pulling it out
again.
Polarization Instruction
QuickTime™ and a
decompressor
are needed t o see t his pict ure.
Power Cord, 2-Wire Polarized Cord
Household model FB-SSCAN
To reduce the risk of electric shock this product is equipped with a polarized alternating
current line plug (a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact a
qualified electrician to replace the obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
Handlermfg.com | 750 SaniVac Instruction Manual | 2012
IMPORTANT NOTICE
WHAT SHOULD YOU DO TO RETURN GOODS
1. Our terms of sale are F.O.B. our plant. Handler makes every effort to insure the
proper delivery of goods, but we cannot guarantee the carrier's performance. Each
product is tested and inspected for proper performance prior to leaving our
facility. The responsibility for damage in transit is the carrier's, whether it is
visible damage or concealed damage.
2. Inspect this shipment IMMEDIATELY. Insist that visible damage or possible
damage be written on the Delivery Receipt by the receiver.
3. Inspect the contents of your shipment within 24 hours of receipt. Using your copy
of our packing list, check for piece count and accuracy immediately to insure
proper billing.
4. If damage is discovered, save all crates, cartons and packaging material until an
inspection has bee made by an agent of the carrier.
5. Incase of damage, notify the delivering carrier IMMEDIATELY requesting that
an inspection be made. Retain a copy of the inspection request for claim purposes.
Failure to notify the freight carrier immediately will result in the loss of your
rights to claim damage.
6. We have taken every precaution to insure safe arrival of your products. We cannot
be responsible for negligence by another party.
7. The receiver of the goods must make claims for incorrectly shipped goods to the
shipper within 15days of receipt of delivery.
RETURNING GOODS
1. DO NOT return merchandise without our authorization. You must call first for a
return authorization number.
2. We will not accept returned merchandise from the carrier unless our authorization
NUMBER has been issued, and is clearly marked on the outside of the carton.
3. We will not accept goods (i.e. dust collectors) that are not cleaned and free of dust
and debris. The merchandise will be shipped back.
HANDLER MFG.
612 NORTH AVENUE EAST, WESTFIELD, NEW JERSEY 07090
Handlermfg.com | 750 SaniVac Instruction Manual | 2012
WARRANTY
This HANDLER product is warranted to be free from defects in material and workmanship,
when used under the conditions recommended by the manufacturer, and/or the purpose for
which the product was intended, for a period of 12 months from the date of shipment from
factory to job site of original owner. Products purchased from distributor warehouse stock
are warranted for a period of 18 months from date of shipment from the manufacturer’s
warehouse.
In all cases, the full name and address of the distributor must be supplied, along with the
name of the customer, product name and number, and serial number. A copy of the original
invoice, showing date of purchase must accompany the warranty repair request.
This warranty will apply to equipment installed, operated and maintained in accordance
with HANDLER procedures and recommendations.
During the life of this warranty, HANDLER will repair or replace (At HANDLER’s option)
free of charge. F.O.B. its plant, any defective part or assembly, if such defect occurred in
normal service and was not due to apparent misuse, abuse, or accident.
Any warranty service performed in the field must be authorized by HANDLER MFG.
Unauthorized service voids the warranty and any resulting charge will not be paid by
HANDLER MFG.
HANDLER MFG. makes no other warranties or guarantees, expressed or implied.
The merchantability of the components is expressly excluded. The manufacturer assumes
no liability for indirect or consequential damages.
Detach or copy and mail back to the address below.
WARRANTY FORM
Customer Name:
Address:
City:
State:
Zip Code:
Description of Product
Model Number:
Distributor:
Distributor’s Address:
HANDLER MFG.
612 NORTH AVENUE EAST, PO BOX 520
WESTFIELD, NEW JERSEY 07090-0520
|