R/Flash function button, see para-
graph 4.6
flashes during an incoming call;
remains lit during a phone conver-
sation
3
INSTALLATION
2. insert the supplied batteries into the bat-
tery compartment according to the mark-
ings.
FX-5500
FX-5520
3.1 Base station:
Intercom button (only functional with
multiple handsets)
Telephone connection:
3. Slide the battery cover back onto the
handset and place the handset on the
base/charger station.
4. Leave the handset continuously during
15 hours on the base station, to cradle/
charge the batteries properly.
illuminates when the speaker functi-
on is enabled
USER MANUAL
1. insert the small plug of the telephone cable
into the TEL.LINE input at the rear of the
base (depress the plug until you hear a
click)
2. Plug the phone connector into the phone
socket.
1 OVERVIEW HANDSETBUTTONS
Redial button
Keypad
illuminates when the ringtone of the
handset is disabled
OK / MENU button
to open the menu and to confirm a
selection
flashes when you’ve received a new
voicemail message
4
CALLING
4.1Answering calls:
Press the key phone-on to accept a call
Power supply:
Correction button, to delete the last
input;
2 DISPLAY OVERVIEW
1. insert the adaptor plug into the DC 6V
input at the bottom of the base
2. plug the adaptor into a 230 Volts wall
socket
battery indication:
remains lit when within range from
the base; is off when out of range
from the base
: battery is full
press the Call button again to enable
the speaker function
: battery still 2/3 full
: battery only 1/3 full, recharging
is recommended
: battery almost empty, the
handset may switch off at any mo-
ment
: to open the Caller-ID memory
: to open the phonebook memory
4.2 End the call:
flashes when you’ve received new
calls; disappears when the Caller-ID
memory of the concerned handset
has been fully checked
keep in mind that when using the
FX-5520, each handset must be
checked separately
/
: buttons: to scroll settings
3.2 Cradle/charger:
press the key phone-off to end a call
To end a call, you can also place the
handset back on the base station or the
cradle/charger.
and memories
If your phone has been delivered with multi-
ple handsets, 2 batteries and a cradle/char-
ger with adapter will be included for every
handset. Plug the adapter of these chargers
in a 230 Volt mains socket.
Call button: to answer incoming calls
press the Call button again to ena-
ble the speaker function
illuminates when using the
/
buttons to show additional options or
memories in the display
4.3 Dialing numbers:
Direct dialing:
Press the phone-on key and enter
End button: briefly press to end a
call; press and hold to switch off the
handset
3.3 Handset:
illuminates while reading the Cal-
ler-ID memory
illuminates when the number is too
long to be shown in the display,
press the # button to view the rest of
the number
1. Open the battery compartment of the
handset, by sliding the battery cover
down.
the phone number through the key-
board; this number will be dialed
directly.
illuminates when reading the last
dialled number memory
Block dialing:
Enter the phone number through the key-
board.
• press and hold the # button for at least 2
seconds to insert a dialing pause
4.6 Handset search function:
to switch off:
copy to the phonebook memory / deleting
press the Redial button and
6.2 Programming:
1. press the MENU button and then the OK
In case you’ve misplaced the handset, you
can easily find it again as follows:
briefly press the button at the bottom of the
base.
pick up the handset from the base or charger
and press and hold the End button for 2 sec-
onds to completely switch off the handset
button
search for the desired number 2. press the OK button and enter the name
using the keypad
• press the
input
button to delete any incorrect
The handset will start ringing for 30 seconds
while the text ‘PAGING’ appears in the display. press and hold the End button for 2 seconds
The handset will stop ringing after 30 seconds
or after pressing a random button (handset)
or when pressing the button (base) again to
manually stop the signal earlier.
to switch on:
press the MENU button and select:
3. press the OK button and use the keypad
to enter the phone number
press and hold the # button for 2 sec-
onds to insert a dialing pause
4. press the OK button
•
SAVE NUMBER to save the selected
number
to switch the handset on again
The handset also switches on when replac-
ing it onto the base or charger.
press the phone-on key; the number
will be dialed
•
•
•
EDIT ENTRY to edit the selected number
DELETE to delete the selected number
DELETE ALL to delete all last dialed
numbers
dialing from the phonebook memory:
press the Phonebook button
and search for the desired
contact
4.9 Call duration:
6.3 Dialing memory contacts:
press the honebook button
and search for the desired
contact
4.7 Voicemail notification: ( )(*)
In case the carrier left a Voicemail message for
you, a notification symbol flashes in the display
of the handset.
This symbol goes off as soon as you have
listened to this message. This symbol also
disappears after resetting the phone (see
paragraph 11.2).
During the phone call, the elapsed call dura-
tion is displayed on the handset display.
10 seconds after disconnecting the call, the
call duration timer will disappear from the
display.
press the OK button and follow the on-screen
instructions
6
PHONEBOOK
press the phone-on key; the number
will be dialed
6.1 Introduction:
press the phone-on key; the number
will be dialed
The handset is provided with a phonebook
memory with a capacity of 50 contacts, each
with a phonenumber of up to 24 digits and a
name of up to 14 characters.
The phonebook memory in the handset is
connected to the function Caller Identifica-
5 REDIALLING
4.4 Speaker volume:
Each handset memorizes the 10 last num-
bers you’ve dialed with the handset. You can
redial these numbers as follows:
press the Redial button,
6.4 Correcting:
You can only adjust the speaker
volume during a call. You can choose
from 5 levels. Use the
*: This function is only available on the FSK
system and when this is supported by the
carrier.
1. press the MENU button
2. press the OK button and select EDIT
ENTRY
/
but-
tons to increase or decrease the volume.
search for the desired re- tion. When you are called by somebody,
cently dialed number and whose name and number you have pro-
3. press the OK button and search for the
desired contact
4.8 To switch off the handset:
4.5 R/Flash:
You can completely switch off the handset to
press the phone-on
key; the number will be dialed
grammed in the memory, the name of this
person is also displayed beside the number
on the display of your handset.
4. press the OK button and press the
button to delete the name
5. use the keypad to enter the new name
and press the OK button
6. repeat this for the number and press the
OK button
During the call, shortly press the key save battery power or in case you don’t want
R to give a FLASH pulse.
The interruption time of the FLASH pulse is
adjustable; for this, see in paragraph 11.2.
to be disturbed:
|