FUTABA R7008SB User Manual

FASSTest-2.4GHz Bidirectional Communication System  
S.BUS2 / S.BUS Port and 8 Channels for Conventional System Receiver  
R7008SB  
1M23N17454  
Thank you for purchasing a Futaba R7008SB FASSTest-2.4GHz compatible receiver. The R7008SB receiver features bi-directional communication  
with a FASSTest Futaba transmitter using the S.Bus2 port. Using the S.Bus2 port an impressive array of telemetry sensors may be utilized. It also  
includes both standard PWM output ports and S.Bus output ports.  
Applicable systems: Futaba FASSTest-2.4GHz system transmitter  
Do not bend the coaxial cable. It causes damage.  
Usage precaution  
• Analog servos cannot be used with the R7008SB in the FASSTest  
12CH mode.  
The antennas must be mounted in such a way to assure  
they are strain relieved.  
• The R7008SB receiver can only be used with FASSTest capable  
transmitters.  
Keep the antenna as far away from the motor, ESC and  
other noise sources as you possibly can.  
• Don't connect to Extra Voltage before turning on a receiver.  
WARNING  
Be sure that the two antennas are placed at 90 degrees to  
each other.  
• The R7008SB has two antennas. In order to maximize signal reception  
and promote safe modeling Futaba has adopted a diversity antenna  
system. This allows the receiver to obtain RF signals on both antennas  
and fly problem-free.  
Changes or modification not expressly approved by the  
party responsible for compliance could void the user’s  
authority to operate the equipment.  
The R7008SB receiver should be protected from vibration  
by foam rubber, Velcro or similar mounting methods.  
Antenna installation for carbon fuselage  
Protect from moisture.  
WARNING  
Keep away from conductive materials to avoid short cir-  
cuits.  
You must leave 30mm at the tip of the antenna fully ex-  
posed. The exposed antenna should be secured so that it  
cannot move around or back inside of your aircraft.  
Antenna installation precaution  
Do not cut or bundle the receiver antenna wire.  
(Antenna installation)  
(Typical installation)  
Extra Voltage  
Port  
90˚  
It connects with the  
battery for power, etc.  
External voltage input  
cable of an option is  
used. The voltage of  
the battery can be  
displayed with a  
S.BUS Servo  
Servo for conventional  
S.BUS Gyro  
system  
transmitter.  
Channel1 output  
Channel8 output  
HUB  
LED  
Link/Mode switch  
(It is not used for a link.)  
S.BUS port (8/SB)  
Temperature  
Sensor  
S.BUS2  
Voltage  
Antenna  
Please refer the table below for LED status vs  
receiver's condition.  
port  
Sensor  
R7008SB  
(S.BUS2)  
HUB  
Voltage  
Sensor  
LED Indication  
Battery to 7/B  
Green  
Off  
Red  
Solid  
Off  
Status  
Terminal box  
RPM  
No signal reception  
Receiving signals  
Sensor  
Solid  
Altitude  
Sensor  
Alternate blink  
Unrecoverable error (EEPROM, etc.)  
HUB  
HUB  
Altitude  
Sensor  
Compliance Information Statement  
(for U.S.A.)  
S.BUS2 Tool  
This device, trade name Futaba Corporation of America, model number  
R7008SB, complies with part15 of the FCC Rules. Operation is subject to the  
following two conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received, including interference  
that may cause undesired operation.  
R7008SB Specifications  
FASSTest-2.4GHz system(18CH/12CH mode)/S.BUS2 and S.BUS port  
and 8 channels for conventional system receiver  
(3) This module meets the requirements for a mobile device that may be used  
at separation distances of more than 20cm from human body.  
To meet the RF exposure requirements of the FCC this device shall not be co-  
located with another transmitting device.  
The responsible party of this device compliance is:  
Futaba Service Center  
• Dual antenna diversity  
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)  
• Weight: 0.38 oz. (10.9g)  
• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)  
• Battery F/S Voltage: It sets up with a transmitter  
• Extra Voltage port: 0 70V DC  
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.  
TEL (217)398-8970 or E-mail: [email protected] (Support)  
* Be sure that when using ESCs regulated output the capacity of the ESC must  
meet your usage condition.  

White Rodgers Acm1400 User Manual
Sanyo Nbl414r User Manual
Ricoh Aficio 3260c User Manual 2
Panasonic Kx F155ba User Manual
Netcomm 3100 User Manual
HITACHI 32LD9000TA User Manual
EMERSON VILTER User Manual
DELL 1815DN User Manual
CRAFTSMAN 315.218050 User Manual
ACER EMACHINES E732G User Manual