FUTABA R6203SB User Manual

FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) System  
S.BUS Port and 3 Channels for Conventional System  
High-speed Receiver  
R6203SB  
Thank you for purchasing a Futaba R6203SB FASST-2.4GHz  
Usage condition for conventional system  
output (Ch1-3) on "High Speed mode"  
compatible receiver.  
The R6203SB has an S.BUS system output port and a  
conventional system channel outputs. It can also be used with  
conventional system servos, etc. in addition to S.BUS system  
compatible servos and gyros, etc.  
CAUTION  
The "High Speed mode" accept the digital  
servos only or most type of peripherals.  
When the linking procedure is performed, R6203SB  
recognizes the signal mode (FASST-2.4GHz 7ch mode or  
8ch/10ch/Multi-ch mode) automatically.  
• If any analog servos connected to these output as it  
will cause malfunction. Please check the peripherals if  
there's any malfunction with whole stick lever throw. If any  
malfunction occur please change the operation mode to  
"Normal mode."  
In addition, the operating mode (high-speed mode/normal  
mode) can be selected.  
Applicable systems: FASST-2.4GHz 7ch or 8ch/10ch/Multi-ch system  
Antenna installation precaution  
Usage precautions about the power source  
We do not recommend to use the power source of less than  
4.0V but if to use the lower voltage source please keep in  
mind the condition shown below.  
WARNING  
Be sure that the two antennas are placed at 90  
degrees to each other.  
• Fail Safe function MUST be in "off" since the battery f/s will  
disturb the normal operation.  
• Futaba's dual antenna diversity, or DAD, then seamlessly  
selects the best signal reception between these antennas to  
ensure that there is no loss of signal.  
• Please make sure that the full loaded condition of the ESC  
and the servos won't disturb the receiver operation before  
start flight.  
Antenna installation for carbon fuse  
This is very important since the receiver will stop operation  
when the supply voltage drops to less than 3.5V.  
WARNING  
The antenna portion of 30mm tip must be fully  
• Please be sure that the ESC or servos can keep flawless  
operation till such a lower voltage.  
exposed.  
The power source voltage must not exceed the servo's  
rating.  
• Please make sure that the exposed portion won't be slided  
back in the fuse by the wind pressure or other force during  
the flight session.  
Link/Mode switch  
(Connectors)  
(Antenna installation)  
LED  
• Channel 2 output for conventional  
90˚  
system (2)  
• Channel 1 output for conventional  
system (1)  
• Channel 3 output for conventional  
system (3)/Battery terminal (B)  
S.BUS Port (S.BUS)  
R6203SB  
R6203SB Specifications  
FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system/S.BUS port  
and 3 channels for conventional system/high-speed receiver  
• Dual antenna diversity  
• Size: 0.89 x 1.47 x 0.37 in. (22.5 x 37.4 x 9.3 mm)  
• Weight: 0.25 oz. (7.2g)  
• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)  
*Be sure that when using ESC's regulated output the capacity of the ESC  
must meet your usage condition.  
Compliance Information Statement  
(for U.S.A.)  
This device, trade name Futaba Corporation of America, model  
number R6203SB, complies with part15 of the FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received, including  
interference that may cause undesiredoperation.  
*The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S  
function doesn't work properly when other type battery is used.  
*The fail safe function can be set for each channel when on "Multi-ch" mode,  
however, it differs according to the transmitter. When on "7ch" mode, the  
fail safe function can be set for 3-channel only.  
The responsible party of this device compliance is:  
Futaba Service Center  
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.  
TEL (217)398-8970 or E-mail: [email protected] (Support)  
*S.BUS port: R6203SB can be used up to 7 channels or less on the "7ch"  
mode and 16 channels + DG1/2 or less on the "8ch/10ch/Multi-ch" mode,  
however, it differs according to the transmitter.  

Whisperkool 081310 User Manual
Sears 53ds900078 User Manual
Schumacher Se 1252ma User Manual
Panasonic Cs Xe9eke User Manual
Milwaukee 48 59 0255 User Manual
GE AJK08 User Manual
CRAFTSMAN 917.387210 User Manual
BLACK DECKER VEC1093DBD User Manual
BLACK DECKER RO410 User Manual
ACER EMACHINES E520 User Manual