FUJITSU FI 7240 User Manual

P3PC-5742-03EN  
fi 7140/fi 7240 Image Scanner  
- -  
Getting Started  
Thank you for purchasing the fi-7140/fi-7240 color image scanner. This manual describes the preparation  
required to use this product. Follow the procedures in this manual. Make sure to read the attached "Safety  
Precautions" manual before using the scanner. For details about scanner functions and features, basic  
operation, daily care, consumable replacement and troubleshooting, refer to the Operator's Guide (PDF).  
The Operator's Guide is included in the Setup DVD-ROM.  
Microsoft product screenshots in this manual are reprinted with permission from Microsoft Corporation.  
ISIS is a trademark of Open Text.  
Intel, Pentium, and Intel Core are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other  
countries.  
ABBYY™ FineReader™ Engine © ABBYY. OCR by ABBYY  
ABBYY and FineReader are trademarks of ABBYY Software, Ltd. which may be registered in some  
jurisdictions.  
ScanSnap and PaperStream are registered trademarks or trademarks of PFU Limited in Japan.  
Other company names and product names are the registered trademarks or trademarks of the respective  
companies.  
December 2019  
© PFU Limited 2015-2019  
Checking the Components  
Make sure that all items shown below are included in the package. If any other packaging is provided, make  
sure to keep it as well. The components must be handled with care.  
The box and packaging materials are required for storage and transportation of the scanner. Do not throw  
them away. If anything is missing or damaged, contact your FUJITSU scanner dealer or an authorized  
FUJITSU scanner service provider.  
[fi-7140]  
[fi-7240]  
ADF Paper Chute (Feeder) (×1)  
Scanner (×1)  
USB Cable (×1)  
AC Adapter (×1)  
AC Cable (×1)  
Setup DVD-ROM (×1)  
Safety Precautions (×1)  
Note: The contents may vary depending on the country.  
1
Manual  
Hard Disk 5,400 rpm or more  
Drive (Recommended: 7,200 rpm or more)  
Includes Safety Precautions, Getting Started,  
Operator's Guide, and fi-718PR Imprinter  
Operator's Guide.  
1 GB or more  
Memory  
(Recommended: 4 GB or more)  
Scanner Central Admin Agent  
Used to centralize the management of multiple  
scanners, by allowing you to apply firmware  
updates simultaneously, monitor the operating  
status, and check the scanner information.  
Note that required applications will differ  
depending on the form of operation.  
For details, refer to the Scanner Central Admin  
User’s Guide.  
Display 1024 × 768 pixels or more,  
Resolution65,536 colors or more  
Hard Disk 11 GB or more of free hard disk space  
Space (*2)  
DVD Drive  
Required for installing the software  
Interface USB 2.0/1.1  
*1: The software operates as a desktop  
application.  
fi Series Online Update  
*2: Required disk space varies according to the  
file size of the scanned images.  
An application that is used to check the latest  
update program of the software and firmware  
related to the fi series and update them. For  
details, refer to the fi Series Online Update  
Help.  
ATTENTION  
If the system requirements above are not  
satisfied, the scanner may not operate.  
Scanning speed will slow down in the following  
cases:  
- The CPU or the memory does not meet the  
required specifications  
System Requirements  
The system requirements are as follows.  
- The version of the USB port or the USB hub  
is USB 1.1  
®
Windows Server 2008 R2 Standard  
(64-bit)  
®
Windows 7 Home Premium  
HINT  
(32-bit/64-bit)  
The screenshots used in this manual are of  
Windows® 7. The actual windows and  
operations may differ depending on the  
operating system.  
Where there is no distinction between the  
different versions of the operating system  
shown in the table of system requirements, the  
general term Windows® is used.  
®
Windows 7 Professional  
(32-bit/64-bit)  
Windows® 7 Enterprise (32-bit/64-bit)  
®
Windows 7 Ultimate (32-bit/64-bit)  
®
Windows Server 2012 Standard  
(64-bit) (*1)  
Windows Server 2012 R2 Standard  
®
(64-bit) (*1)  
®
Operating  
System  
Windows 8.1 (32-bit/64-bit) (*1)  
®
Windows 8.1 Pro (32-bit/64-bit) (*1)  
®
Windows 8.1 Enterprise (*1)  
®
Windows 10 Home (32-bit/64-bit)  
(*1)  
®
Windows 10 Pro (32-bit/64-bit) (*1)  
Windows 10 Enterprise  
®
(32-bit/64-bit) (*1)  
®
Windows 10 Education  
(32-bit/64-bit) (*1)  
®
Windows Server 2016 Standard  
(64-bit) (*1)  
Windows Server 2019 Standard  
®
(64-bit) (*1)  
®
®
Intel Pentium 4 1.8 GHz or higher  
(Recommended:  
CPU  
®
Intel Core™ i5 2.5 GHz or higher,  
except mobile device processors)  
3
5. Follow the instructions on the screen to  
Installing the Bundled Software  
Install the bundled software from the Setup DVD-  
ROM in the following procedure.  
Note that there are two ways to install the bundled  
software: select [Installation (Recommended)] to  
install all the software required to operate the  
scanner, or [Installation (Custom)] to select and  
install the software as needed.  
proceed with the installation.  
1.InPsertfaolrlmatisotenp(sC1u. stoto3m. in) "Installation  
(Recommended) (page 4)".  
2. Click the [Installation (Custom)] button.  
ATTENTION  
If an old version of the software is installed  
already, uninstall it first.  
For details about the uninstallation procedures,  
refer to "A.5 Uninstalling the Software" in the  
Operator's Guide.  
3. Select the check box for the software to  
Installation (Recommended)  
The following software are installed:  
PaperStream IP (TWAIN)  
PaperStream IP (TWAIN x64)  
Software Operation Panel  
Error Recovery Guide  
PaperStream Capture  
Manual  
Scanner Central Admin Agent  
fi Series Online Update  
install and click the [Next] button.  
4. Follow the instructions on the screen to  
proceed with the installation.  
Installing the Scanner  
Install the scanner in the following procedure.  
1. Place the scanner at its installation site.  
ATTENTION  
Carry the scanner by supporting it from the  
bottom.  
1. Turn on the computer and log onto  
Windows® as a user with Administrator  
privileges.  
fi-7140  
Outer Dimensions  
Installation Space  
2. Insert the Setup DVD-ROM into the DVD  
drive.  
The [fi Series Setup] screen appears.  
380  
(1348.906)  
HINT  
If the [fi Series Setup] screen does not  
appear, double-click "Setup.exe" in the  
Setup DVD-ROM via Windows Explorer or  
[Computer].  
163  
(6.42)  
(6.69)  
170  
700(27.56)  
3. Click the scanner model name to be used  
(if the window for selecting a model name  
is displayed).  
300  
(11.81)  
400  
(15.75)  
Unit: mm (in.)  
4. Click the [Installation (Recommended)]  
button.  
4
     
fi-7240  
Outer Dimensions  
Connecting the Cables  
Connect each cable in the following procedure.  
AC Cable  
Installation Space  
450  
(17.72)  
234  
(9.21)  
Power Connector  
4
4
AC Adapter  
300  
(11.81)  
400  
(15.75)  
577(22.72)  
800(31.50)  
2
3
Unit: mm (in.)  
USB Connector  
2. Unlock the transport lock switch.  
1
2
For fi-7240, there is a carrier unit inside the  
flatbed which is fixed in place to prevent  
damage during transportation.  
USB Cable  
Slide the transport lock switch on the front.  
CAUTION  
Only use the supplied AC adapter. Not doing  
so may cause the scanner to malfunction.  
Furthermore, do not use the supplied AC  
adaptor for other products.  
Locked  
Unlocked  
1. Confirm that the computer is turned off.  
2. Connect the USB cable to the USB  
connector of the scanner and USB port of  
the computer.  
Transport Lock Switch  
ATTENTION  
3. Attach the ADF paper chute (Feeder).  
Use the supplied USB cable.  
If you connect the scanner with USB 2.0,  
it is required that the USB port and the  
hub be compliant with USB 2.0. The  
scanning speed slows down when you  
connect the scanner with USB 1.1.  
Connect it with  
Insert the tabs into the slots on the back of  
the scanner in the direction indicated by the  
1
arrow  
, and tilt the ADF paper chute  
backwards in the direction indicated by the  
2
arrow  
until it locks in place.  
Tab  
ADF Paper Chute  
(Feeder)  
the USB mark  
facing up.  
Side Guides  
USB Mark  
ATTENTION  
Insert the ADF paper chute (Feeder) firmly  
so that there is no space between the  
scanner.  
5
3. Connect the AC cable to the AC adapter  
2. Turn on the computer.  
(hereinafter called the "power cable").  
The scanner is automatically detected.  
ATTENTION  
WARNING  
If the [Found New Hardware] dialog box  
appears, select [Locate and install driver  
software (recommended)], and follow the  
instructions on the screen to install the  
driver.  
Only use the supplied power cable.  
To prevent electrical shock or scanner  
malfunction, do not perform the following:  
Use a different power cable  
Use the supplied power cable for other  
devices  
3. Load a document in the scanner.  
1. Pull out the chute extensions according to the  
4. Connect the power cable to the power  
connector of the scanner and the power  
outlet.  
length of the document.  
2. Pull the stacker out, slide stacker extension 1  
and stacker extension 2 toward you  
according to the length of the document, and  
lift the stopper up.  
HINT  
When you plug the cable into the outlet, the  
[Power] button on the scanner’s operator  
panel will flash once. Note that this is an  
initial diagnosis and not a malfunction.  
3. Load the document face-down in the ADF  
paper chute (Feeder).  
4. Adjust the side guides to the width of the  
document.  
fi-7140  
Test-Scan  
Side Guides  
Chute  
Extension 2  
Follow the procedure described below to check  
that documents can be scanned correctly by using  
PaperStream Capture and PaperStream IP  
(TWAIN).  
Chute  
Extension 1  
Stacker  
Extension 1  
1. Press the [Power] button on the operator  
panel.  
ADF Paper  
Chute (Feeder)  
LED Indicator  
Stacker  
Stacker Extension 2  
Check  
Function  
Function  
Number Display  
Stopper  
Send to  
Scan  
/Stop  
fi-7240  
Power  
Chute Extension 2  
[Power] Button  
Chute Extension 1  
The scanner is turned on, and the [Power]  
button lights in green.  
During initialization, the Function Number  
Display changes as follows: "8" "P"   
"0" "1". The scanner is ready when "1" is  
displayed.  
Side Guides  
ATTENTION  
If "1" is not displayed on the Function  
Number Display, refer to "Chapter 7  
Troubleshooting" in the Operator's Guide.  
ADF Paper  
Chute (Feeder)  
Stacker  
HINT  
Stopper  
When you press the [Power] button, the  
LED indicator will flash once. Note that this  
is an initial diagnosis and not a malfunction.  
6
4. Start up PaperStream Capture.  
ATTENTION  
Windows Server® 2008 R2/Windows®  
7
When an error occurs with the scanner, the  
indication on the Function Number Display  
changes as follows:  
Select the [Start] menu [All Programs]   
[PaperStream Capture] [PaperStream  
Capture].  
For temporarry errors  
The letter "J" or "U" and an "error code" appear  
alternately.  
Windows Server® 2012  
Right-click the Start screen, select [All apps]  
on the app bar, and then select  
[PaperStream Capture] under [PaperStream  
Capture].  
For device errors  
The letter "E", "F", "C", "H", "A" or "L" and an  
"alarm number" appear alternately.  
In that case, refer to "Chapter 7  
Troubleshooting" in the Operator's Guide.  
Windows Server® 2012 R2/Windows® 8.1  
Click [] on the lower left side of the Start  
screen, and then select [PaperStream  
Capture] under [PaperStream Capture].  
To display [], move the mouse cursor.  
For details about other scanning features, refer to  
"Chapter 4 Various Ways to Scan" in the  
Operator's Guide.  
Windows® 10/Windows Server® 2016/  
Windows Server® 2019  
Select the [Start] menu [PaperStream  
Capture] [PaperStream Capture].  
5. Click the [Scan] button in the Menu Area.  
6. Click one of the three types of document  
profiles that are prepared beforehand.  
Below is an example of when the document  
profile [Black and White] is clicked.  
The document is scanned, and the  
scanned image is displayed.  
7
Contact for Purchasing Consumables  
or Cleaning Materials  
Contact for Inquiries  
Refer to the contact list on the last page of the  
Safety Precautions manual.  
contact.html  
ABBYY FineReader for ScanSnap™  
Windows Server® 2008 R2/Windows®  
7
Select the [Start] menu [All Programs]   
[ABBYY FineReader for ScanSnap(TM)]   
[User’s Guide] [Technical Support].  
Windows Server® 2012  
Right-click the Start screen, select [All apps]  
on the app bar, and then select [User’s  
Guide] under [ABBYY FineReader for  
ScanSnap(TM)] [Technical Support].  
Windows Server® 2012 R2/Windows® 8.1  
Click [] on the lower left side of the Start  
screen, and then select [User’s Guide] under  
[ABBYY FineReader for ScanSnap(TM)]   
[Technical Support].  
To display [], move the mouse cursor.  
Windows® 10/Windows Server® 2016/  
Windows Server® 2019  
Select the [Start] menu [ABBYY  
FineReader for ScanSnap(TM)] [User’s  
Guide] [Technical Support].  
Color Image Scanner fi Series  
For other inquiries regarding the scanner,  
refer to the following web page:  
If the solution to your problem cannot be  
found on the above web page, refer to the  
contact information for your Fujitsu office on  
the following web page:  
Notice  
Copying of the contents of this document in whole  
or in part and copying of the scanner application is  
prohibited under the copyright law.  
The contents of this document are subject to  
change without notice.  
Regulatory Model P3670A/P3670C  
8

York Eco Hfc 410a User Manual
Tanaka Tc 355 User Manual
Sanyo 09kls71 User Manual
Samsung Sf 330 User Manual
Omega Speaker Systems 41100 User Manual
NEC NP UM383WL User Manual
LG CMS2460F 02 User Manual
Lexmark All In One Printer Pro4000c User Manual
GE CSWONBLPWF1NN User Manual
ACER ASPIRE E1 E1 430PG User Manual