Safety Information
Product Description
Installation Instructions
Item #110-527
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
¨
Mount the receiver on a wall near a grounded electrical outlet. The nail
or screw head must extend at least 3/16 in. out from the wall. Hang the
receiver from the slot on the back of the unit onto a nail or screw. Plug
the power supply cord of the receiver into the outlet.
NOTE: This product is suitable for outdoor use and use in damp
locations.
1. Power indicator light:
The power indicator light
indicates that the receiver is on.
USE AND CARE GUIDE
¨
¨
Plug the device cord into the receptacle at the bottom of the
receiver.
Install the battery into the transmitter.
2. Outlet:
3-PACK WIRELESS INDOOR/OUTDOOR
REMOTE CONTROL SWITCH
1
The outlet located on the
bottom of the receiver allows
the user to plug an array of
devices into it. Plug the light or
Operating Instructions
¨Reorient or relocate the receiving antenna.
device to be controlled by the
remote into the outlet.
CH
Using the remote control
¨Increase the separation between the equipment and the receiver.
¨Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
¨Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
1
¨
To set up the three receivers (outlets) with various devices, locate
channel 1, 2, 3, on the remote control and the 1, 2, 3, on each receiver
and select ON/OFF function with the same channel (CH , CH , CH .)
respectively.
3. Remote control:
¨
Channel
:
To control various devices
with three different
channels.
Operation is subject to the following two conditions:
2
3
¨
¨
To activate the receiver, press the “I” button of the remote control.
The red LED of the remote control will illuminate momentarily and the
LED of the receiver will remain illuminated.
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation of the device.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
¨
¨
I : When the “I” button is
pressed, it will override the
program to on function.
O : When the “O” button is
pressed, it will override the
program to off function.
CH
To turn the receiver OFF, press the “O” button of the remote control.
The LED on the receiver will shut off.
I
I
I
O
O
O
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
Store indoors when not in use.
Questions, problems, missing parts? Before returning to the store,
8 a.m. - 6 p.m., EST, Monday - Friday
1-866-308-3976
RATINGS
Installation Instructions
125 VAC, 60 Hz
HOMEDEPOT.COM
10 A General Purpose
10 A Resistive
WARNING: The device must be mounted in a vertical position
with the receptacle facing downward and with the receptacle at
least 2 ft. above the ground level to prevent water immersion.
I
I
I
THANK YOU
O
O
O
We appreciate the trust and confidence you have placed in
Defiant through the purchase of this outdoor wireless remote control.
Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Defiant!
1000 W Tungsten
1/3 HP Motor
Maintenance
Replacing the battery
2
WARNING: Do not mutilate or place the battery in a fire. The
battery may burst or release toxic materials. Do not short circuit
or reverse polarity as this may cause burns.
¨
¨
Remove the battery compartment cover from the back of the remote
control by sliding the cover in the direction that its threads curve.
Remove the old battery and place a new DC 12V Type A23 battery into
the battery compartment, correctly observing the polarity indications (+/−)
inside the battery compartment.
¨
¨
Replace the battery compartment cover.
Dispose or recycle spent/discharged batteries in compliance with all
applicable laws. For detailed information, contact your local solid waste
authority.
Questions, problems, missing parts? Before returning to the store,
Troubleshooting
8 a.m. - 6 p.m., EST, Monday - Friday
1-866-308-3976
Problem
Solution
The lights do not turn on and
off via remote control.
Confirm remote operation after replacing
batteries.
HOMEDEPOT.COM
The lights do not turn on, even
Ensure the lights are functional by
when the power indicator light plugging them directly into the outlet.
indicates that the receiver is on.
Be sure that the lights are in the “ON”
position if they have their own switch.
Be sure that the outlet that the receiver
is plugged into is active.
Made in China
SAVE THESE INSTRUCTIONS!
|