M32-KPDA612-XQ Rev. 18/04-00
DOOR DRILLING FOR NEW INSTALLATION
3
NOTE: If your door already has holes, skip to step
4
A. Using the template, mark the door and drill the holes, and chisel out a mortise.
FOR
1-1/2” (38mm)
1”
Centerline
OR
25 mm
1-1/2” (38mm)
2-1/8"(54 mm)
1/8”
3 mm
I
OR
1"
2-1/8"(54 mm)
(25 mm)
2-1/8"
a. Outline
(54 mm)
O
b. Chisel 1/8” (3mm) deep
Questions, problems, missing parts? Before returning to the store,
call Deꢀant Customer Service
Backset
SCAN FOR
INSTALLATION
TOLL FREE HELP LINE 1-877-ONE-LOCK
HOMEDEPOT.COM
B. PREPARE DOOR JAMB
a.
f
Door jamb hole dimension
a. 1-3/16" (30 mm)
b. 1-9/64" (29 mm)
c. 7/8" (22 mm)
08:30 a.m.-05:30 p.m., EST, Monday - Friday
c
1”
25 mm
b
https://goo.gl/mcceCM
e
J
d. 5/32" (4 mm)
e. 2-1/4" (57 mm)
f. 1" (25 mm)
a
d
f
Door jamb hole dimension
a. 1-/2" (13 mm)
WARRANTY
c
b. 1-1/16" (27 mm)
c. 1/8" (19 mm)
d. 1/16" (1.5 mm)
e. 2-5/16" (58 mm)
f. 1-7/16" (36 mm)
P
LIMITED LIFETIME MECHANICAL AND 1 YEAR ELECTRONIC WARRANTY
b
b. Outline
e
The retailer of this product, hereby warrants, subject to the conditions set forth below, that it will either repair or replace, at its option, this product if it
proves to be defective by reason of improper workmanship or materials within the original purchaser's limited time. In order to obtain repairs or
replacement under this limited warranty you must bring this product to the retailer's store in which you bought it.
c. Chisel 1/8” (3mm) deep
d
a
Original purchaser: This limited warranty is limited to the original purchaser at retail of this product from retailer.
Except to the extent prohibited by applicable law, no other warranties, whether express or implied, including the warranties of merchantability and ꢀtness
for a particular purpose, shall apply to this product. Under no circumstances shall retailer be liable for consequential or incidental damages in connection
with this product. To the extent retailer is prohibited by applicable law from excluding implied warranties, the duration of such implied warranties which
are not excludable shall be the original purchaser's lifetime. Some states do not allow the limitation on how long an implied warranty lasts, so the above
limitation on the duration of implied warranties which are not excludable, if any, may not apply to you. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion of incidental or consequential damages may not apply to you.
Retailer neither assumes not authorizes any representative or other person to assume for it any obligation or liability other than such as is expressly set
forth herein. This limited warranty gives you speciꢀc legal rights, and you may also have other rights which vary from state to state.
Choose Faceplate
4
1
Safety Information
OR
Read the precautions and instructions in this manual before installing and using this lock. Save this manual for future reference.
CAUTION:
Please use four alkaline batteries for the best performance.
A. Do not attempt to disassemble any internal components of the lockset. Doing so will void the limited warranty.
B. Do not drop or hit the lockset. Too much shock may result in permanent damage.
C. Do not use pins or sharp objects to press the keypad.
D. Always create a backup of information you wish to keep (Master Code, User Codes,etc.) Please use the last page of this booklet as a reference.
E. Promptly change the Master Code before operating this lockset
5
Set the Latch Backset
5
6
2-3/8’’
(60 mm)
2-3/4’’
(70 mm)
CARE and MAINTENANCE:
The following instructions should be followed to properly protect and maintain your lockset:
180º
OR
A. Remove locks, or do not install locks, prior to painting your door.
B. Periodically clean with mild soap and a soft cloth only.
C. Do not use any abrasives or chemical products containing alcohol, benzene, acids, and avoid using sharp or abrasive objects to clean this lockset.
D. Do not allow any water or liquids into the lockset during installation.
6
Pre-installation – Tools Required / Hardware Included
2
Installation
A. INSTALL LATCH
B. INSTALL STRIKE PLATE IN DOOR JAMB
Tap Latch Flush
K
Optional
Optional
Optional
Optional
Optional
Optional
CC
WARNING:
If the door needs to be drilled, please be familiar with how to use a drill safely and understand all of the door preparation steps before proceeding.
OR
CC
NOTE: If required, bend the
Backset
adjustable tang on the strike to
eliminate a loose fit between the
door and the door stop.
P
Wood Block (not included)
PACKAGE CONTENTS LIST
Hardware Used
CC
Hardware Used
CC
Actual Size
G
BB
Actual Size
Part
Description
A
B
C
D
E
F
G
H
I
Key
Exterior Assembly
Power Cable
C. INSTALL LEVER
SWITCH HANDLES
(IF DESIRED)
NOTE: Levers installed in reverse
will not affect the product’s
performance.
F
INSIDE
OUTSIDE
Torque blade
Exterior Gasket
Mounting Plate
Interior Assembly
Battery Cover
Latch
Hardware Used
DD
H
J
K
L
Strike Plate
Dust Box
Drive-in Collar (Optional)
Pull
B
DD
Insert pick-up pin into catch hole and pull lever off. Repeat the same on the inside to
remove inside lever.
Actual Size
AA
2-3/8” (60 mm)
2-3/4” (70 mm)
J
OR
A
K
I
CC
L
E
Swap levers. Align the hole on the lever with the catch hole, and insert the
lever until secure.
D
C
D. INSTALL ELECTRONIC DEADBOLT
Thread the cable through
the hole and under the latch.
ᕡ
DD
Part
Description
M
N
O
P
Outside Lever Assembly
Inside Lever Assembly
Latch
Adapter collar
Strike Plate
For installation into 1-1/2”(38mm) bore hole,
simply pry the adapter collar off with a
screwdriver.
O
Q
Drive-in Collar (Optional)
The latch bolt should be
in retracted position.
M
N
Install the lock assemblies
ᕢ
Remove the Battery Cover
Slide the cable through the
notch in mounting plate.
CC
P
Q
Press
AA
HARDWARE CONTENTS (Actual Size)
The bulged part of the mounting plate
must face towards the door.
Hardware Used
AA
AA
BB
1-13/16" (46 mm) Mounting Bolt
Qty. 2
Actual Size
13/16" (20 mm) Screw
Qty. 2
The cable must be arranged as shown in the diagram.
Insert screws
and tighten.
Connect the cable
ꢀrmly into
connector port .
BB
CC
DD
3/4 in. (19 mm) Wood screws
Qty. 8
1-23/64 in. (34mm) mounting screws
Qty. 2
Hardware Used
BB
Note : The metal connector
side should face outward.
Actual Size
BEFORE PROCEEDING
Check Dimensions
CAUTION :
1.Please use four alkaline batteries for better performance. Be sure to insert them correctly by matching the + and – polarity
markings. Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline batteries.
2.Install and test lock with door OPENED to avoid being locked out.
1-1/2” (38mm)
OR
2-1/8” (54mm)
2-1/8” (54mm)
1” (25mm)
1-3/8” - 1-3/4”
(35mm - 45mm)
Enter default Master Code (123456)
2-3/8” (60mm)
OR
2-3/4” (70mm)
and the lock will set up bolt
Install batteries
Install battery cover
direction to complete installation.
|