Item #470-906
Model #49815
UPC #043180498151
Use and Care Guide
INDOOR DIGITAL TIMER
Before You Begin
Product Features
Product Specifications
□
Set one or more multiple ON/OFF settings for each day of the week, daily cycles, or weekday - weekend
cycles
□
□
Single pole, no neutral wire is needed
Replaces a standard wall switch or older spring wound timers
□
□
Stores up to 4 individual programs
A Random feature which turns the lights off and on between 30 minutes before and after the programmed
time, giving the appearance that somebody is currently home
RATINGS
120 VAC,
60 Hz
5A/ 600W
Tungsten
5A/ 600W
Resistive
40o C Max
Temp
Pre-Installation Requirements
Hardware Included
□
This timer will only operate with incandescent, halogen, or xenon bulbs. Do not use this timer with CFL or
LED bulbs.
□
This timer can only be installed in a single pole installation. Do not install on a 3-way switch.
Safety Information
AA - Wire Nut x3
BB - Screw x2
RISK OF ELECTRIC SHOCK:
Shut off the power at the fuse box or circuit breaker
before installation
Do not use in wet locations
Use indoors only
Suggested Tools
RISK OF ELECTRIC FIRE:
Do not use to control appliances that contain heating
elements such as cooking appliances, heaters, and irons
Do not exceed electrical ratings
WARNING
Do not use to control receptacles
Use only copper wire with this device
Not for use with CFL or fluorescent bulbs. Use with incandescent, xenon, or halogen bulbs.
The safety ground must be connected for proper operation.
Phillips screwdriver
Wire stripper
If you are unsure or unclear about this installation, contact a qualified licensed electrician.
This timer is equipped with memory back up that will protect the settings for up to 60 minutes. You never have to
replace batteries. The internal backup requires about 12 hours to fully charge.
Installation Terms and Options
BASIC WIRING TERMINOLOGY
To better familiarize yourself with the wiring terminology and concepts referenced in this manual, please review the following information before you begin wiring this timer to your switch box.
If at any time during the wiring process you become uncertain, please contact a certified electrician.
□ Line: This is the 120 volt feed wire (line in).
□ Load: This is the wire that controls the fixture (load out).
□ Single-Pole Switch: A single-pole switch only controls a fixture from a single location. A typical example of where you would find a single-pole switch is your bedroom or bathroom light
switch.
Programming Instructional Video
To view an instructional video on how to program this product:
corner of this instruction sheet in the search field.
2. Click on your product from the list of search results and click on the video link in the Product
Overview section.
Single Pole Installation
INSTALLING THE TIMER
1
Black
a. Turn OFF the main power at the circuit breaker or fuse box.
Line
b. Remove the existing switch.
c. Connect the wires of the timer to the wall box as shown in Figure 1, using the wire nuts provided.
Blue
Load
□ Connect the line wire to the black wire from the timer.
□ Connect the load wire to the blue wire from the timer.
□ Connect the ground wire to the green wire from the timer. Timer will not operate without a ground.
Green
Ground
d. Ensure that all wire nuts are secure, and tuck the wires into the wall box, leaving room for the timer.
e. Using the screws provided, mount the timer to the wall box, being careful not to crush any wires.
f. Turn the main power ON at the circuit breaker or fuse box.
Figure 1
g. Place power switch (1) in ON position.
Initial Setup
PRODUCT DESCRIPTION
S
M
T
W
T
F
S
Part Description
2
3
5
POWER switch: Slide the switch to the left to disrupt power to the timer/ fixture. Slide switch
1
to the right to restore power to the timer/ fixture.
2
3
4
SETUP/PGM button: Press to enter/exit programming mode.
“+” button: Press to scroll upward.
7
8
9
1
SETUP
PGM
AUTO
RANDOM
ENTER
ON/OFF
“–“ button: Press to scroll downward.
+
-
6
4
RESET
5
ON/OFF button: Turns the timer ON/OFF.
POWER
OFF ON
6
7
8
9
RESET button: Press and hold for three seconds to reset the system.
AUTO button: Press once to activate auto mode.
RANDOM button: Press once to activate the random feature.
ENTER button: Press to confirm indicated settings.
CONTINUE TO PAGE 2 TO COMPLETE SETUP AND PROGRAMMING
IP08292014
HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
|