ElEctric StOVE HEatEr
i N S t r U c t i O N M a N U a l
QC212-MBKP
attENtiON:
1. Find a location for the stove heater
that is protected from direct sunlight.
2. Do not plug the unit into the power
outlet before reading all instructions.
S a F E t Y i N S t r U c t i O N S / O P E r at i O N
iMPOrtaNt
lEG aSSEMBlY
Please note: when you open the carton
carefully check the unit and make sure there
is no damage. If you have any problems with
the unit, with how the various functions
work, or damaged or missing parts please
call 1-800-459-4409 (8:30 am to 5:00 pm,
EST) immediately for service.
Before using your unit please install the legs
as shown in diagram below.
NOTE: DO NOT RETURN UNIT TO
THE STORE BEFORE CALLING THE
TOLL FREE NUMBER.
Do not dispose of your cartons until you
are completely satisfied with your new
stove heater.
NOtE: light bulbs may become loose
during shipping. if the flame effect is dim
or does not work, please check that light
bulb or bulbs are finger tight in socket.
See instructions for replacing bulb or bulbs.
Please do not return the sample to the store
before checking light bulbs.
after completely reading instructions,
confirm that all controls on stove are in the
OFF position. Plug the unit into a 15 amp,
120 volt outlet.
OPEratiON
NOtE: the stove may emit a slight harmless
odor when first turned on. this is caused by
activating the internal heater components for
the first time and should not occur again.
controls and switches are located on front
panel inside the glass door.
a 15 aMP circuit is required to operate this
heater. if the breaker trips when the heater
is used then you may need to move the heater
to another location or unplug other appliances
that are on the same circuit. if you require
an extension cord, use one that is rated at
1875 watts.
i/O: Press this button into the “i” position for
main power and flame effect. the indicator
light will turn on.
HEatiNG: For heat function, press this
switch while the O/i switch is in the “i”
position for heat. the indicator light will
turn on.
3
O P E r at i O N
tHErMOStat: to adjust the temperature
WarNiNG
to your individual requirements, turn the
thermostat dial to the right (clockwise) to
increase the temperature and to the left to
decrease the temperature. this thermostat
control dial can only be used while the
i/O switch and heating switch are in the
“i” position. When the heater reaches
the desired temperature, the heater and
heating indicator light will turn off, but the
fan will continue to operate. adjust this
knob to restart the heater.NOtE: When
the FlaME switch is turned to the OFF
position, all other heater functions will stop
even though the switches may be in the “i”
position.
Disconnect power and unplug the power
cord before attempting any maintenance or
cleaning to reduce the risk of fire, electric
shock or personal injury. the bulbs in your
unit can become extremely hot. allow at least
10 minutes between turning off the unit and
removing the light bulbs to avoid accidental
burning of the skin.
FlaME EFFEct
the fire effect is created with the use of a
40 watt B-10 candelabra light bulb with an
E-12 (small) socket base. the light bulb will
have to be replaced from time to time when
they burn out.
tHErMOStat cONtrOl
the heat output is controlled by the
thermostat, according to the room
temperature. Set the thermostat dial fully
clockwise to the maximum position initially.
During normal operation, the stove heater will
always give you simulated flame function. if
the intensity of flame suddenly increases, it
means that the light bulb is going to burn out.
When the room is warm enough, reduce the
setting by slowly turning the thermostat dial
anti-clockwise until the heater just clicks OFF.
this will then maintain the room temperature
at the desired level.
replace the light bulb immediately, according
to the instruction. Do not operate the stove
heater when the light bulb burns out or without
the light bulb.
cHaNGiNG tHE
liGHt BUlB
caUtiON:
if you use this heater in conjunction with a
thermal control, a program controller, a timer
or any other device that switches the heater on
automatically, remember to observe all safety
warnings at all times.
StEP 1: Open the door of unit with the handle.
StEP 2: loosen the 2 screws at the front of
the log set inside the stove. carefully
lift the logset up far enough to access
the light bulbs. You will find 1 x 40 W
type B-10 candelabra light bulb with
E-12 socket base at the bottom.
the stove heater has safety overheat
protection. if the overheat protection trips,
switch off all switch buttons and wait
approximately 5 -10 minutes. it should reset
automatically once the unit cools down.
StEP 3: replace the burned out light
4
M a i N t E N a N c E
bulb using a new 40 W type B-10
candelabra light bulb.
StEP 4: reinstall the logset.
StEP 5: Plug in the unit.
clEaNiNG
to clean unit, first turn off the controls on the
unit and unplug the unit from power source.
to clean glass door; remove dust with clean
dry cloth or to remove finger prints and other
marks clean glass with clean damp cloth. Do
not use abrasive cleaners or spray liquids on
the glass door surface.
Metal and metal painted parts should be
cleaned with damp cloth. Do not use abrasive
cleaners or spray liquids on these surfaces.
StOraGE
When the heater is not in use, the heater
should be stored in a dry location, away from
possible damage. the power cord should be
stored properly to avoid contact with hot or
sharp objects.
5
W a r r a N t Y
WarraNtY claiM PrOcEDUrE
WarraNtY
if a claimable defect occurs, please fill out
a claim form through our website at: www.
qualitycraft.com or contact our customer
service department at 1-800-459-4409
(8:30am to 5:00pm, ESt).
Every electric stove is tested before it leaves
the factory and it is guaranteed for one year.
if the unit should fail to operate correctly
within one year from the date of purchase,
call customer service at 1-800-459-4409
(8:30am to 5:00pm, ESt). We will, at our
discretion either repair or replace the unit.
it will have to be returned to us freight prepaid
and we will return the repaired or replaced unit
to you freight prepaid. the company’s
sole obligation is to repair or replace the unit.
this warranty is void if in the opinion of Quality
craft the unit has been tampered with, altered,
misused, damaged, abused or used with
the wrong power source. light bulbs are not
covered by this warranty. the warranty is for
homeowner use only and does not cover units
used in commercial situations.
Before you make your claim call, please make
sure you have:
1. the description of the electric stove
2. Proof of sale
3. Details regarding the defect
4. Name and address of the owner
and installer
claims must be filled out in writing and
returned within six (6) months of appearance
of defect. Failure to comply with this stipulation
will make the warranty null and void. We
reserve the right to a thirty-day (30) delay
following receipt of claim in which to inspect
the product. We assume no responsibility for
labor costs, removing/replacing a previously
installed product, transportation or return of a
product.
iMPOrtED BY
Quality craft
laval, Quebec, canada H7c 0a5
1-800-459-4409
Made in china
6
|