Dell Wyse 5060 Thin Client
User Guide
Regulatory Model: N07D
Regulatory Type: N07D001
1
Welcome to Dell Wyse 5060 thin client
Dell Wyse 5060 thin client is a mid-range thin client. These mid-range thin clients have a x86 processor, which allows you to run Dell Wyse
ThinOS, Dell Wyse ThinLinux, Windows Embedded Standard 7P (WES7P), and Windows 10 IoT Enterprise (WIE10). The platform is used as
a thin client by connecting to any monitor and allows you to use a remote access client for Virtual Desktop Infrastructure (VDI) or cloud-
based computing.
Topics:
•
•
About this guide
This guide helps to install, use and maintain Wyse 5060 thin clients which run Wyse ThinOS, Wyse ThinLinux, Windows Embedded
Standard 7P, and Windows 10 IoT Enterprise. It provides hardware specifications and OS specific configurations to help you work with
Wyse 5060 thin clients.
Dell Wyse external references
This section provides links to Dell support sites for Dell Wyse thin clients.
•
•
•
•
Dell Service and Support — Latest software images
Dell and the Environment — Information about Dell compliance with RoHS and with the Waste Electrical and Electronic Equipment
(WEEE)
•
•
Dell and e-Recycling — Information about recycling and reuse of Dell products
Dell Warranty Registration* — Register your product
Welcome to Dell Wyse 5060 thin client
3
2
Hardware setup
This section discusses the following topics:
•
•
Dell Wyse 5060 thin client hardware setup
Accessing thin client BIOS settings
Topics:
•
•
Dell Wyse 5060 thin client hardware installation
For more information on the hardware installation, see Dell Wyse 5060 thin client Quick Start Guide.
Accessing thin client BIOS settings
1
Start the thin client.
The Dell logo is displayed.
2
During the start-up, press the Delete key.
The BIOS Settings dialog box is displayed.
Enter the default password Fireport.
Make the required changes in the BIOS Settings.
3
4
4
Hardware setup
3
Logging in to the Dell Wyse 5060 thin client
This section includes the following topics:
Topics:
•
•
•
•
Logging in to the Wyse 5060 thin client running
WES7P
For security reasons, automatic logon to a user desktop is enabled on the thin client by default.
To log in as a different user or administrator:
1
Click Start > Log off, to log out from the current desktop and hold the Shift key until the logon window is displayed.
2
Log in by using one of the following options:
•
•
Administrators — The default name is Administrator and the default password is DellCCCvdi.
Users — The default name is User and the default password is DellCCCvdi.
IMPORTANT: Passwords are case-sensitive.
NOTE: To log in as an administrator, configure your thin client by using Auto
Logon.
3
If automatic logon is not enabled, the logon window is displayed when you start the thin client. You can log in using the options
mentioned in step 2.
We recommend you change the default passwords of your thin client. To change a password:
WARNING: Disable the File Based Write Filter before you change a password, and then enable it after your change. If you use
thin client with the write filter turned OFF (except for image upgrades, applying security patches, registry changes and
application installation) the thin client may damage the Flash/SSD storage and will invalidate the product warranty.
1
Log in as an Administrator.
2
3
Press CTRL+ALT+DEL. The Windows Security window is displayed.
Click Change a Password, and then in the Change a Password dialog box, enter the old and new passwords as applicable.
Logging in to the Dell Wyse 5060 thin client running
Dell Wyse ThinOS
What you see after logging on to the server depends on the administrator configurations.
Logging in to the Dell Wyse 5060 thin client
5
•
•
Users of Classic Desktop - See the classic ThinOS desktop with full taskbar, and Connect Manager familiar to ThinOS users. This is
the default option and is recommended for terminal server environments with published applications and for backward compatibility
with ThinOS 6.x versions.
Users of Zero Desktop - See the Zero Desktop with the Zero Toolbar showing the assigned list of connections. This option is
recommended for VDI and full-screen-only connections.
However, in both the cases, you can select the desktop option you want (Classic Desktop or Zero Desktop) and create the connections you
need by using the Visual Experience tab in the Remote Connections dialog box.
To open the Remote Connections dialog box, perform the following task:
•
Classic Desktop — Click User Name, and then select System Setup > Remote Connections.
NOTE: User Name is the user who is logged-on and is located at the lower-left pane of the taskbar
•
Zero Desktop — Click the System Settings icon on the Zero Toolbar, and then select Remote Connections.
Logging in to the Dell Wyse 5060 thin client running
Dell Wyse ThinLinux
On initial configuration, Dell recommends that you connect by using a wired connection by plugging in the network connected Ethernet
cable to your thin client.
After you start your thin client, you are automatically logged in to the local thinuser account. By default, the password of the thinuser
account is set to thinuser.
NOTE: In cases where a GDM login is needed (for example, AD/Domain login, PNAgent login and so on), the auto-login option
can be turned off through the GUI or by using the INI.
By using the Admin mode, you can perform system administration tasks such as adding or removing connections and making specific
device settings.
To enter the Admin mode:
1
Click the Switch to Admin button from Setting application screen.
2
Enter the default root password in the Password Needed window. The default root password is admin.
Logging on to the Wyse 5060 thin client running
WIE10
Whatever we view during the turn on or during the reboot of thin client device depends on the administrators configuration. After creating
user account, an administrator can configure a user account to log on automatically or require manual logon with user credentials.
WARNING:
•
Be sure to disable the Unified Write Filter (UWF) before you change a password on the thin client, and then enable the UWF after
your change. If you use thin client with the write filter turned OFF (except for image upgrades, applying security patches, registry
changes and application installation) the thin client may damage the Flash/SSD storage and will invalidate the product warranty.
•
To change the password, hold CTRL+ALT+DEL key combination, and then click Change a password. However, this feature is not
applicable for the User accounts.
6
Logging in to the Dell Wyse 5060 thin client
4
Displays
This section provides information about the multiple monitor configurations.
Topics:
•
•
•
•
Dual Monitor Display in WES7P
You can configure dual monitor display in Wyse 5060 thin client running WES7P that are dual-monitor- capable.
To configure the dual monitor settings in Wyse 5060 thin client running WES7P,go to Start > Control Panel > Display > Change Display
Settings.
TIP: While configuring Dual-Monitor settings, set the same screen resolution for both the
monitors.
Configuring the dual head display settings in Dell
Wyse ThinOS
To configure the dual head display settings in Wyse ThinOS:
1
From the desktop menu, click System Setup, and then click Display.
The Display dialog box is displayed.
2
Click the Dual Head tab, and use the following guidelines:
Displays
7
This feature is applicable for supported dual-monitor-capable thin clients only.
a
b
c
Dual Head—Select Mirror Mode to have the two monitors work in a matching state, or Span Mode to have the two monitors
work individually.
Main Screen—Select which of the two monitors you want to be the main screen (Screen1 or Screen2). The other screen is
extended from the main screen.
Layout—Select how you want the two monitors to be oriented to each other.
Horizontal — where you move between the monitors from the left and right of the screens.
Vertical— where you move between the monitors from the top and bottom of the screens.
d
e
Alignment— Select how you want the monitors to be aligned Bottom, Center, or Top.
Bottom means screens are bottom-aligned in a horizontal orientation; Center means screens are center-aligned; Top means
screens are top-aligned in a horizontal orientation.
Taskbar (Classic Desktop Only)—Select under which screen you want the taskbar to appear Whole Screen or Main Screen
Gamma Supported Monitors Only— Use the Gamma Setup tab to adjust the saturation values for Red, Green and Blue on
VGA connected monitors supporting gamma settings, if you feel the default settings are too light. Be aware that the Gamma
Setup tab will be disabled once you click Save+Exit. You can enable it again by setting rgamma={1-100} ggamma={1-100}
bgamma={1-100} in the Resolution INI parameter. For more information, see Dell Wyse ThinOS INI Guide.
8
Displays
For Swap dual screens, when you set Main Screen to Screen2, an additional check box is displayed at the bottom of the tab that
allows you to swap dual screens. If you clear the check box, the Screen1 is usually the left one or the top one in dual display.
When you set Main Screen to Screen2, the main screen is changed to the right screen or bottom screen. If you select the Swap
dual screens check box, you are able to set Main Screen to Screen2, but still have it at the left side or the top side, which is
considered more user friendly.
Configuring your display on Dell Wyse ThinLinux
By default, the Customize your display screen is available in both User mode and Admin mode. Any changes to display preferences made
through this screen is saved and available for the built-in thinuser. In a Dual-monitor configuration, if both monitors are connected, then by
default, the monitors are in extended mode. The primary monitor is on the left (monitor 1) and the secondary monitor is on the right
(monitor 2). The resolutions of the monitors are auto detected by the system by analyzing the monitor’s capabilities.
1
Click the Display tab.
The Customize Your Display page is displayed.
Displays
9
Figure 1. Display Settings
2
3
Select the preferred Resolution from the drop-down list.
Select the Rotation type from the drop-down list.
•
•
•
•
Normal
Right
Left
Upside-down
4
5
6
Click the ON/OFF button to switch between dual display and mirror mode in a dual monitor configuration.
Click the ON/OFF button to enable the Set as primary option. This option allows you to set the selected monitor as primary.
Click the ON/OFF button to enable the Monitor On/Off option. This option allows you to switch off and switch on the preferred
monitor in a dual monitor configuration.
Configuring dual monitor display on WIE10
You can use the Screen Resolution window to configure dual monitor settings on your dual-monitor capable thin client device.
To open the Screen Resolution window:
1
Log in as an Admin.
2
On the Start menu, click Control Panel > Display > Change Display Settings.
The Screen Resolution window is displayed. For detailed instructions on how to configure the screen resolution, go to
10
Displays
5
Networks
This section describes about the network configurations of Wyse 5060 thin client.
Topics:
•
•
•
•
Configuring network settings on WES7P
If Dell Wyse supported WLAN hardware modules are installed on the thin client, clicking the Network and Sharing Center icon in the
Control Panel allows you to:
1
Manage Wireless Networks (click the Manage Wireless Networks link):
•
Add —Click Add to open and use the wizard to add a wireless network to edit an existing wireless network, right-click it, and then
select Properties to open and use the Network Properties dialog box.
•
•
•
Adapter Properties —Click Adapter Properties to open and use the properties dialog box for the wireless adapter.
Profile Types —Click Profile Types to open and use a dialog box to the enable or disable the ability to create Per User Profiles.
Network and Sharing Center - Click Network Sharing Center to return to the Network and Sharing Center dialog box provides
network settings, and gives access to network settings.
2
3
Change Adapter Settings click the Change Adapter Settings link:
•
•
Click Organize to open the list of options you can use to organize your network connections.
Select a connection to display the list of command buttons you can use to view the status, connect to, enable, disable, diagnose,
rename, and change the settings of the connection.
Change Advanced Sharing Settings (click the Change Advanced Sharing Settings link): Select the network profile settings you want
for each of your networks.
Configuring the network settings on Dell Wyse
ThinOS
To configure the network settings use the following options:
•
•
•
•
Networks
11
Configuring the General settings
To configure the general network settings:
1
From the desktop menu, click System Setup, and then click Network Setup.
The Network Setup dialog box is displayed.
2
Click the General tab, and use the following guidelines:
a
To set the default gateway, select the type of network interface from the available options.
1
Single Network support — Either wireless or wired network is connected.
•
•
•
ENET — Click this option, if you want set up the Ethernet Wired Network Connection.
WLAN — Click this option, if you want to set up the Wireless Network Connection.
If you use wireless network after selecting ENET connection or wired network after selecting WLAN connection, then
the system log "WLAN: set default gate way xxx.xxx.xxx.xxx" for first case and "ENET: set default gate way
xxx.xxx.xxx.xxx" for second case are printed to ensure that the UI setting reflects the actual usage.
NOTE: The User Interface (UI) will not be changed automatically.
2
Dual Network support — Both wireless and wired networks are connected. The default gateway is determined by the UI
settings.
b
Enter the URL address of the DNS domain in the DNS Domain box.
12
Networks
c
Enter the IP address of the DNS server in the DNS Server box.
Use of DNS is optional. DNS allows you to specify remote systems by their host names rather than IP addresses. If a specific IP
address (instead of a name) is entered for a connection, it is used to make the connection. Enter the DNS domain and the
network address of an available DNS server. The function of the DNS domain entry is to provide a default suffix to be used in
name resolution. The values for these two boxes may be supplied by a DHCP server. If the DHCP server supplies these values,
they replace any locally configured values. If the DHCP server does not supply these values, the locally configured values will be
used.
NOTE: You can enter up to 16 DNS server addresses, separated by a semicolon, comma, or space. The first
address is for the primary DNS server and the rest are secondary DNS servers or backup DNS servers .
Enter the IP address of the WINS server in the WINS Server box.
d
Use of WINS is optional. Enter the network address of an available WINS name server. WINS allows you to specify remote
systems by their host names rather than IP addresses. If a specific IP address (instead of a name) is entered for a connection, it
is used to make the connection. These entries can be supplied through DHCP, if DHCP is used. DNS and WINS provide
essentially the same function, name resolution. If both DNS and WINS are available, the thin client attempts to resolve the name
using DNS first and then WINS.
You can enter two WINS server addresses (primary and secondary), separated by a semicolon, comma, or space.
e
Enter the digit multiplier of 30 seconds in the TCP Timeout box to set the time-out value of a TCP connection. The value must
be 1 or 2 which means the connection time-out value is from 1x30= 30 seconds to 2x30= 60 seconds. If the data for connecting
to the server is not acknowledged and the connection is timed out, setting the time-out period retransmits the sent data and
again tries to connect to the server till the connection is established.
3
Click OK to save the settings.
Configuring the DHCP Options Settings
To configure the options settings:
1
From the desktop menu, click System Setup, and then click Network Setup.
The Network Setup dialog box is displayed.
2
Click the Options tab, and use the following guidelines:
Networks
13
a
b
c
d
DHCP Option IDs — Enter the supported DHCP options. Each value can only be used once and must be between 128 and 254.
Interpret DHCP Vendor-Specific Info — Select this check box for automatic interpretation of the vendor information.
DHCP Vendor ID — Shows the DHCP Vendor ID when the dynamically allocated over DHCP/BOOTP option is selected.
DHCP UserClass ID — Shows the DHCP UserClass ID when the dynamically allocated over DHCP/BOOTP option is selected.
3
Click OK to save the settings.
Configuring the ENET Settings
To configure the ENET settings:
1
From the desktop menu, click System Setup, and then click Network Setup.
The Network Setup dialog box is displayed.
2
Click the ENET tab, and use the following guidelines:
14
Networks
a
Ethernet Speed — Normally the default (Auto-Detect) should be selected, but another selection can be made if automatic
negotiation is not supported by your network equipment. Selections include Auto-Detect, 10 MB Half-Duplex, 10 MB Full-
Duplex, 100 MB Half-Duplex, 100 MB Full-Duplex, and 1 GB Full-Duplex.
The 10 MB Full-Duplex option can be selected locally at the device, however, this mode may need to be negotiated through
AutoDetect.
b
The IPV4 check box is selected by default. Click Properties to set various options supported by IPV4.
•
Dynamically allocated over DHCP/BOOTP — Selecting this option enables your thin client to automatically receive
information from the DHCP server. The network administrator must configure the DHCP server using DHCP options to
provide information. Any value provided by the DHCP server replaces any value entered locally on the Options tab, however,
locally entered values are used if the DHCP server fails to provide replacement values.
•
Statically specified IP Address — Select this option to manual enter the IP Address, Subnet Mask and Default Gateway:
•
•
IP Address — Must be a valid network address in the server environment. The network administrator must provide this
information.
Subnet Mask — Enter the value of the subnet mask. A subnet mask is used to gain access to machines on other
subnets. The subnet mask is used to differentiate the location of other IP addresses with two choices: same subnet or
other subnet. If the location is other subnet, messages sent to that address must be sent through the Default Gateway,
whether specified through local configuration or through DHCP. The network administrator must provide this value.
•
Default Gateway — Use of gateways is optional. Gateways are used to interconnect multiple networks (routing or
delivering IP packets between them). The default gateway is used for accessing the internet or an intranet with multiple
subnets. If no gateway is specified, the thin client can only address other systems on the same subnet. Enter the address
of the router that connects the thin client to the internet. The address must exist on the same subnet as the thin client
as defined by the IP address and the subnet mask. If DHCP is used, the address can be supplied through DHCP.
c
d
Select the IPV6 check box, and then click Advanced to select various IPV6 supported setting options from the available check
boxes.
Click properties and use the following guidelines:
•
•
Wait DHCP — Selecting this option enables your thin client to wait for IPV6 DHCP before the sign-in, if not selected the
system will only wait for IPV4 DHCP if enabled.
Dynamically allocated over DHCP/BOOTP — Selecting this option enables your thin client to automatically receive
information from the DHCP server. The network administrator must configure the DHCP server (using DHCP options) to
Networks
15
provide information. Any value provided by the DHCP server replaces any value entered locally on the Optionstab, however,
locally entered values are used if the DHCP server fails to provide replacement values.
•
Statically specified IP Address — Select this option to manually enter the IP Address, Subnet Mask and Default Gateway.
•
•
•
IP Address — Must be a valid network address in the server environment. The network administrator must provide this
information.
Subnet Mask — Enter the value of the subnet mask. For more information, see various options supported by IPV4 in
this section.
Default Gateway — Use of gateways is optional. For more information, see various options supported by IPV4 in this
section.
•
DNS Servers — Use of DNS is optional. DNS allows you to specify remote systems by their host names rather than IP
addresses. If a specific IP address (instead of a name) is entered for a connection, it is rather than DNS is used to make the
connection. Enter the network address of an available DNS server. The value for this box may be supplied by a DHCP server.
If the DHCP server supplies this value, it replaces any locally configured value. If the DHCP server does not supply this value,
the locally configured value is used.
e
Select the check box to enable IEEE802.1x Authentication.
•
EAP Type — If you have enabled the Enable IEEEE 802.1x authentication check box, select the EAP Type option you want
(TLS, LEAP or PEAP).
•
TLS — If you select the TLS option, click Properties to open and configure the Authentication Properties dialog box.
•
Select the Validate Server Certificate check box because it is mandatory to validate your server certificate.
NOTE:
The CA certificate must be installed on the thin client. Also note that the server certificate text
field supports a maximum of approximately 127 characters, and supports multiple server names.
•
•
If you select the Connect to these servers check box, the box is enabled where you can enter the IP address of server.
Click Browse to find and select the Client Certificate file and Private Key file you want.
The following kinds of server names are supported — all examples are based on Cert common name company.dell.com
NOTE:
Using only the FQDN, that is company.wyse.com does not work. You must use one of the options (note that
*.dell.com is the most common option as multiple authentication servers may exist): servername.dell.com
*.dell.com
*dell.com
*.com
f
LEAP — If you select the LEAP option, click Properties to open and configure the Authentication Properties dialog box. Be
sure to use the correct username and password for authentication. The maximum length for the username or the password is 64
characters.
g
PEAP — If you select the PEAP option, click Properties to open and configure the Authentication Properties dialog box. Be
sure to select either EAP_GTC or EAP_MSCHAPv2, and then use the correct username, password and domain. Validate Server
Certificate is optional.
NOTE:
The server certificate text box for LEAP and PEAP supports a maximum of approximately 127 characters, and
supports multiple server names.
h
To configure EAP-GTC, enter the username only. The password or PIN is required when authenticating.
To configure EAP-MSCHAPv2, enter the username, password and domain.
IMPORTANT: The domain/username in the username box is supported, but you must leave the domain box
blank.
16
Networks
The CA certificate must be installed on the thin client and the server certificate is forced to be validated. When EAP-
MSCCHAPV2 is selected in EAP type in the Authentication Properties dialog box (for PEEP IEEE802.1x authentication), an
option to hide the domain is available for selection. Username and Password boxes are available for use, but the Domain text box
is disabled.
3
Click OK to save the settings.
Configuring the WLAN Settings
1
From the desktop menu, click System Setup, and then click Network Setup.
The Network Setup dialog box is displayed.
2
Click the WLAN tab, and use the following guidelines:
a
Add— Use this option to add and configure a new SSID connection.
You can configure the SSID connection from the available security type options.
Networks
17
b
c
d
After you configure the SSID connection, the added SSID connection is listed on the page of the WLAN tab.
Remove — Use this option, if you want to remove a SSID connection by selecting the SSID connection from the list.
Properties — Use this option to view and configure the authentication properties of a SSID connection that is displayed in the
list.
e
Select the Disable Wireless Device check box, if you want to disable a wireless device.
3
Click OK to save the settings.
Configuring the network settings on Dell
WyseThinLinux
On the System Settings page, click the Network tab to view the Network Settings page.
1
Click the Network icon.
Figure 2. Network Settings
2
The Network settings page is displayed. In the left-pane, the following tabs are available for you to configure.
18
Networks
•
•
•
Wi-Fi
Wired
Network proxy
Figure 3. Network Settings page
Configuring the wi-fi settings
To configure the Wi-Fi settings, perform the following steps:
1
In the left-pane, click Wi-Fi tab.
2
Click the ON/OFF button to enable or disable the Wi-Fi option. The list of wireless SSID is displayed if broadcast is enabled.
Figure 4. Wi-Fi Settings
3
4
5
To connect to Wi-Fi connection, select the preferred wireless SSID from the list displayed.
Click the ON/OFF button to enable or disable the Airplane Mode option after you log in to the session.
Click the Connect to Hidden Wi-Fi Network button. The Connect to Hidden Wi-Fi Network window is displayed.
Networks
19
Figure 5. Hidden Wi-Fi Network
6
Enter the name and security details of the hidden network that you want to connect to.
Table 1. Hidden network
Parameter
Description
Connection
From the drop-down list, select the type of connection.
Network name
Wi-Fi security
Enter the preferred network name.
From the drop-down list, select the security type.
7
On the Network page, click the History button to view the previous Wi-Fi connections and details.
Configuring wired network connection settings
To configure the wired connection settings, perform the following steps:
1
Click the Wired tab. The following attributes are displayed if the network cable is connected to your thin client and wired connection is
established.
•
•
•
•
IP Address
Hardware Address
Default Route
DNS
NOTE: After the network is disconnected, only hardware address and last used information are displayed.
On the lower-right corner of the page, click the Settings icon to configure the Wired Network connections.
In the Details tab, the following attributes are displayed.
2
a
•
•
•
•
•
IP Address
Link Speed
Hardware Address
Default Route
DNS
3
Click the Security tab to configure the 802.1x security settings.
a
Click the ON button to enable the 802.1x Security for your network connection.
b
From the Authentication drop-down list, select the type of authentication you want to set for your network connection. The
available options are:
•
•
•
MDS
TLS
FAST
20
Networks
•
•
Tunneled TLS
Protected EAP (PEAP)
c
If the authentication type is selected as MD5, you must configure the following options:
Table 2. MD5 configuration
Parameter
Description
Username
Enter the Username for the network connection.
Password
Enter the password you want to set for the connection.
Ask for this password every time
If this check box is selected, you will be prompted to enter the
password every time when you connect to the network.
Show Password
Select this check box if you want to allow the user to view the
hidden password.
d
If the authentication type is selected as TLS, you must configure the following options.
Table 3. TLS
Parameter
Description
Identity
Enter your Identity.
User certificate
Select the User certificate from the list or upload your
personal certificate stored locally.
To upload your personal certificate, click the Folder icon, and
then browse to the location where you have stored the
certificate.
CA Certificate
Select the CA certificate from the list or upload your CA
certificate stored locally.
To upload your CA certificate, click the Folder icon, and then
browse to the location where you have stored the certificate.
Private key
Select the private key from the list or upload your private key
stored locally.
To upload your private key, click the Folder icon, and then
browse to the location where you have stored the certificate.
Private key password
Show Password
Enter the password that you want to set for the private key.
Select this check box if you want to allow the user to view the
hidden password.
e
If the authentication type is selected as FAST, you must configure the following options.
Table 4. FAST
Parameter
Description
Anonymous identity
Enter the username you want to set for Anonymous
Authentication Identity.
PAC provisioning
Select this check box to enable the PAC provisioning
authentication. From the drop-down list, select any of the
following PAC provisioning options:
Networks
21
Parameter
Description
Anonymous – Select this option to establish a secure
anonymous TLS communication with the client and provide it
with a PAC.
Authenticated – Select this option to enable a secure server-
side authentication and provide the client with a proxy auto-
config (PAC) file.
Both – Select this option if you want to allow both
Anonymous and Authenticated PAC provisioning.
PAC file
Select the PAC file from the list or upload your CA certificate
stored locally.
To upload your PAC file, click the Folder icon, and then
choose the certificate from the location where you have
stored the certificate.
Inner authentication
From the drop-down list, select the inner authentication
method you want to set. The available options are GTC and
MSCHAPv2.
Username
Enter the Username for the network connection.
Password
Enter the password you want to set for the connection.
Ask for this password every time
If this check box is selected, you will be prompted to enter the
password every time when you connect to the network.
Show Password
Select this check box if you want to allow the user to view the
hidden password.
f
If the authentication type is selected as Tunneled TLS, you must configure the following options.
Table 5. Tunneled TLS
Parameter
Description
Anonymous identity
Enter the username that you want to set for Anonymous
Authentication Identity.
CA certificate
Select the CA certificate from the list or upload your CA
certificate stored locally.
To upload your CA certificate, click the Folder icon, and then
browse to the location where you have stored the certificate.
Inner authentication
From the drop-down list, select the inner authentication
method that you want to set. The available options are GTC
and MSCHAPv2.
Username
Enter the Username for the network connection.
Password
Enter the password that you want to set for the connection.
Ask for this password every time
If this check box is selected, you will be prompted to enter the
password every time when you connect to the network.
22
Networks
Parameter
Description
Show Password
Select this check box if you want to allow the user to view the
hidden password.
g
If the Authentication type is selected as Protected EAP (PEAP), you must configure the following options.
Table 6. Protected EAP (PEAP)
Parameter
Description
Anonymous identity
Enter the username you want to set for Anonymous
Authentication Identity.
CA certificate
Select the CA certificate from the list or upload your CA
certificate stored locally.
To upload your CA certificate, click the Folder icon, and then
browse to the location where you have stored the certificate.
PEAP version
Select the PEAP version type you want to use for EAP
authentication. The available options are:
•
•
•
Automatic
Version 0
Version 1
Inner authentication
From the drop-down list, select the inner authentication
method that you want to set. The available options are GTC
and MSCHAPv2.
Username
Enter the Username for the network connection.
Password
Enter the password that you want to set for the connection.
Ask for this password every time
If this check box is selected, you will be prompted to enter the
password every time when you connect to the network.
Show Password
Select this check box if you want to allow the user to view the
hidden password.
4
Click the Identity tab and configure the following settings:
NOTE: Only Administrators are allowed to authenticate these settings by entering the admin password in the root
privilege authentication dialog box after a particular setting is changed or configured.
a
Name— Specifies the default name of the wired connection. If you want to set your preferred name for the connection, enter
the name and then click Apply.
b
c
d
MAC Address— Specifies the MAC address of the network connection.
Cloned Address— Specifies the IP address that is cloned by the router.
Maximum transmission unit (MTU)— Specifies the size (in bytes) of the largest protocol data unit that the protocol layer can
pass onwards.
e
f
Connect automatically— Select this check box to automatically connect to the network after you plug-in the network wire.
Make available to other users— Select this check box if you want to allow other users to configure these settings.
5
Click the IPv4 tab and do the following:
a
Enable the IPv4 button to configure the IPv4 settings.
b
From the Addresses drop-down menu, select the type of IPv4 configuration. The available options are:
•
•
Automatic (DHCP)
Manual
Networks
23
•
Link-Local Only
c
If Automatic (DHCP) option is selected, you must configure the following options.
Table 7. Automatic (DHCP)
Parameter
Description
DNS
Enable the Automatic button, if you want the thin client to
automatically fetch the DNS Server.
Server
Routes
Specifies the IP address of the DNS Server.
Click the + icon to add a new DNS server to the list.
Enable the Automatic button to turn on the automatic IPv4
routing.
Address
Specifies the Router IP address.
Netmask
Specifies the Netmask. Netmask is used to divide an IP
address into subnets and specify the network's available
hosts.
Gateway
Specifies the IP address of the default Gateway.
Metric
Specifies the Metric value for the network connection.
Use this connection only for resources on its network
Select this check box, if you want to allow the wired
connection only for resources on its network.
d
e
If Manual option is selected, you must specify the IP address, Netmask IP and Gateway IP along with the parameters mentioned
in Table 1: Automatic (DHCP).
If Link-Local Only option is selected, the DNS and Routes options are disabled. This is applicable only for communications within
the host link or the host domain.
6
Click the IPv6 tab and do the following:
a
Enable the IPv6 button to configure the IPv6 settings.
b
From the Addresses drop-down menu, select the type of IPv6 configuration. The available options are:
•
•
•
•
Automatic
Automatic, DHCP only
Manual
Link-Local Only
The IPv6 configuration is similar to configuring the IPv4 Settings. For IPv4 configuration, see the IPv4 settings in this section.
Click the Reset tab and do the following:
7
a
Click Reset to reset the settings for your network connection, including passwords. However, the previous network is displayed
as a preferred network.
b
Click Forget to remove all details relating to this network that you do not want to automatically connect to.
8
Click Apply to save your configured settings.
NOTE: Click the Add Profile tab to add a new network profile. On the right pane, you must configure the following
options:
•
•
•
•
Security
Identity
IPv4
IPv6
The configuration of all these tabs are similar to Wired Network connections configurations described in this section.
24
Networks
Configuring the network proxy settings
To configure the Network proxy settings, complete the following task:
1
Click the Network proxy tab.
2
From the Proxy drop-down menu, select the type of Proxy method you want to deploy. The available Proxy methods are:
•
•
•
None
Manual
Automatic
3
4
If Manual proxy method is selected, you must configure the following options:
a
b
c
d
e
Enter the HTTP Proxy port details for your network connection.
Enter the HTTPS Proxy port details for your network connection.
Enter the FTP Proxy port details for your network connection.
Enter the SOCKS host port details for your network connection.
Use the Ignore Hosts option to set up proxy to ignore all local addresses.
If Automatic proxy method is selected, you must type the configuration URL address in the field.
NOTE: Web Proxy Autodiscovery is used when a Configuration URL is not provided. Dell does not recommend this
option for untrusted public networks.
Adding a network connection
NOTE: Adding additional wired Ethernet connections is allowed but the added interface is not used in any of the ThinLinux
features.
To add a new network connection, complete the following tasks:
1
On the lower-left corner of the page, click the + icon.
The Add Network Connection dialog box is displayed. The following options are listed for you to configure.
•
•
•
•
VPN
Bond
Bridge
VLAN
2
3
Click VPN to add a VPN network connection. You must import a file from the stored location to configure the VPN settings.
Click Bond to add and configure the Bond network connection for your thin client.
a
Click the General tab to select or deselect the following check boxes.
•
•
•
Automatically connect to this network when it is available.
All users may connect to this network.
Automatically connect to VPN when using this connection.
b
Click the Bond tab, and configure the following options:
1
Type a name for your network interface.
2
The number of bonded connections that are set up are listed here. To add a new bond connection, click the Add button
and select the type of connection you want to create. The available options are Ethernet and InfiniBand.
3
Select the type of Network Mode from the drop-down list. The available options are:
•
•
•
Round-robin
Active Backup
XOR
Networks
25
•
•
•
•
Broadcast
802.3ad
Adaptive transmit load balancing
Adaptive load balancing
4
Link Monitoring — Select the type of link monitoring from the drop-down list. The available options are:
•
•
MII (recommended)
ARP
5
6
Enter the time in ms for the link up delay duration.
Enter the time in ms for the link down delay duration.
c
Click the IPv4 Settings tab, and do the following:
From the drop-down list select the following method for IPv4 authentication.
1
•
If Automatic (DHCP) method is selected, you must configure the following options:
1
Additional DNS Servers — Type the IP addresses of domain name users that are used to resolve host names. Use
commas to separate multiple domain name server addresses.
2
Additional Search Domains — Type the IP addresses of domains used when resolving host names. Use commas to
separate multiple domains.
3
4
5
DHCP client ID — Enter the ID for the DHCP client. This client identifier allows the network administrator to
customize your computer’s configuration.
Require IPv4 addressing for this connection to complete — The IPv4 address is required to complete the
connection. If the IPv4 address is not available, then the connection is not configured.
Click the Routes button to edit IPv4 routes for Bond connection.
a
Click Add to add an IP address. After an IP is added, Netmask, Gateway and Metric specific to that IP are
displayed.
b
c
Select the check box if you want to ignore the automatically obtained routes.
Select this check box if you want to use your connection only for resources on that particular network.
•
If Automatic (DHCP) addresses only method is selected, you must configure the following options:
1
DNS Servers — Type the IP addresses of domain name users that are used to resolve host names. Use commas
to separate multiple domain name server addresses.
2
Search domains — Type the IP addresses of domains that are used when resolving host names. Use commas to
separate multiple domains.
3
DHCP client ID — Enter the ID for the DHCP client. This client identifier allows you to customize your computer’s
configuration.
NOTE: The other settings remain same as described in automatic (DHCP) method for IPv4
authentication.
•
If Manual method is selected, you must configure the following options:
1
Click Add to add an IP address. After an IP is added, Netmask, Gateway specific to that IP are displayed.
2
DNS Servers — Type the IP addresses of domain name users that are used to resolve host names. Use commas
to separate multiple domain name server addresses.
3
Search domains — Type the IP addresses of domains used when resolving host names. Use commas to separate
multiple domains.
NOTE: The DHCP client ID option and Ignore automatically obtained routes check boxes
are disabled.
The other settings remains the same as described in automatic (DHCP) method for IPv4
authentication.
•
If Link-Local Only method is selected, the DNS Servers, Search domains, DHCP client ID, and Routes options are
disabled. You can select the Require IPv4 addressing for this connection to complete check box to allow the
26
Networks
connection to complete. The IPv4 address is required to complete the connection. If the IPv4 address is not available,
then the connection is not configured.
•
If Shared to other computers method is selected, the DNS Servers, Search domains, DHCP client ID, and Routes
options are disabled. You can select the Require IPv4 addressing for this connection to complete check box to allow
the connection to complete. The IPv4 address is required to complete the connection. If the IPv4 address is not
available, then the connection is not configured.
d
Click the IPv6 Settings tab. From the drop-down list, select the following method type for IPv4 authentication. The available
options are:
•
•
•
•
•
Ignore
Automatic
Automatic, addresses only
Manual
Link-Local Only
NOTE: The settings are same as configuring the IPv4 settings tab described in this section.
Add and configure the Bridge network connection for your thin client.
4
a
Click the Bridge tab, and configure the following options:
1
Interface name — Type the name for your network interface.
2
Bridged connections — The number of bonded connections that are set up are listed here. To add a new bond connection,
click the Add button and select the type of connection you want to create. The available options are Ethernet, Wi-Fi, and
VLAN.
3
4
5
6
7
8
Aging time — Enter the Aging time duration in seconds.
Enable STP — Select this check box to enable the Spanning Tree Protocol (STP) for your connection.
Priority — Enter the priority value.
Forward delay — Enter the forward delay duration in seconds.
Hello time — Enter the hello time duration in seconds.
Max age — Enter the value for the maximum age.
b
To configure the General tab, IPv4 Settings tab, and IPv6 Settings tab for Bridge connection, see the configuration details for
Bond connection in this section.
5
Configure the VLAN network connection for your thin client.
a
Click the VLAN tab, and configure the following options:
1
Parent interface — Type the name for your parent interface.
2
3
4
5
VLAN id — Enter the value for the VLAN id.
VLAN interface name — Type the name for your VLAN interface.
Cloned MAC address — Type the cloned MAC address.
MTU —Specifies the size (in bytes) of the largest protocol data unit that the protocol layer can pass onwards.
b
To configure the General tab, IPv4 Settings tab, and IPv6 Settings tab for VLAN connection, see the configuration details for
Bond connection in this section.
6
Click Save to save your settings.
Configuring network settings on WIE10
Network services provided to thin clients can include DHCP, FTP file services, and DNS. Configuring your network services depends on the
availability in your environment, designing and managing it.
You can configure your network services using:
Networks
27
Using Dynamic Host Configuration Protocol (DHCP)
A thin client is initially configured to obtain its IP address and network configurations from a DHCP server. A DHCP server provides the IP
address or DNS name of the FTP server and the FTP root-path location of software in Microsoft.msi form for access through the DHCP
upgrade process.
DHCP is recommended to configure and upgrade thin clients as it saves time and efforts needed to complete these processes locally on
multiple thin clients. If a DHCP server is not available, fixed IP addresses can be assigned and must be entered locally for each device.
A DHCP server can also provide the IP address of the WDM server. For more information, Wyse Device Manager (WDM) software for
Using Domain Name System (DNS)
Thin client devices accept valid DNS names registered on a DNS server available to the enterprise intranet. The thin client device sends a
query to DNS server on the network for name to IP resolution. DNS allows hosts to be access by their registered DNS names rather than
their IP address.
Every Windows DNS server in Windows 2000 and later includes Dynamic DNS (DDNS) and every server registers dynamically with the
DNS server. For DHCP entry of DNS domain and server location information, see Using Dynamic Host Configuration Protocol (DHCP)
28
Networks
6
Peripherals
This section provides the information about using and configuring the peripherals on Wyse 5060 thin client.
Topics:
•
•
•
•
Configuring and using Peripherals on WES7P
The thin client has USB ports available on it.
•
•
•
2*USB 2.0 (front)
2*USB 2.0 (rear)
2*USB 3.0 (rear)
To provide the services through the ports, install the appropriate software for the thin client.
NOTE:
•
You can install other services and add-ins that are available from the Dell website for free or for a licensing fee.
For more information, see the Dell Wyse Support Site.
•
You can configure the thin client device to use Bluetooth- enabled Peripherals. For more information, see Bluetooth connections on
Device Manger: Bluetooth Connections
You can access Bluetooth- enabled devices in your thin-client device, if your thin-client has optional Wireless Bluetooth capability.
1
To manage an existing Bluetooth device :
a
b
c
Go to Start > Control Panel > Device Manager
Click Bluetooth Radios.
To manage an existing Bluetooth device, double-click on the Bluetooth icon
You can update drivers using the Driver tab
2
To add Bluetooth- enabled device:
a
Go to Start > Control Panel > Devices and Printers
Devices and Printers window is displayed
b
c
d
Click Add a Device.
Turn on the Bluetooth — enabled devcie and ensure that the device is discoverable.
When the device is discoverable by the thin-client device, click Next and follow the wizard.
Peripherals
29
Configuring peripherals settings on Wyse ThinOS
The Peripherals dialog box enables you to configure the settings for the keyboard, mouse, camera, and printer.
•
•
•
•
Configuring keyboard settings
To configure the Keyboard settings:
1
From the desktop menu, click System Setup, and then click Peripherals.
The Peripherals dialog box is displayed.
2
Click the Keyboard tab and set the Character Set, Keyboard Layout, Delay Before Repeat and Repeat Rate parameters. The following
table explains the parameters present on the Peripherals dialog box.
Parameter
Description
Character Set
Specifies the character set. Each character is represented by a
number. The ASCII character set, for example, uses the numbers
0 through 127 to represent all English characters and special
control characters. European ISO character sets are similar to
ASCII, but they contain additional characters for European
languages.
Keyboard Layout
Presently the keyboard languages listed in the Keyboard layout
drop-down list are supported. The default value is English
(United States).
Delay Before Repeat
Specifies the repeat parameters for held-down key. Select the
Delay before repeat value as either 1/5 second, 1/4 second, 1/3
30
Peripherals
second, 1/2 second, 3/4 second, 1 second, 2 seconds, or No
Repeat. The default is 1/3 second.
Repeat Rate
Select Slow, Medium, or Fast. The default value is Medium.
3
Click OK to save the settings.
Configuring mouse settings
To configure the mouse settings:
1
From the desktop menu, click System Setup, and then click Peripherals.
The Peripherals dialog box is displayed.
2
Click the Mouse tab to select the mouse speed and mouse orientation.
3
4
Select the Swap left and right mouse buttons check box to swap mouse buttons for left-handed operations.
Click OK to save the settings.
Configuring camera settings
Use the Camera tab to interface with cameras that are locally connected to the thin client (USB) and supported by a UVC driver. When
using the HDX RealTime webcam feature of XenDesktop 5 or XenApp 6, you can control options such as maximum resolution and frames
per second (10 FPS is recommended).
By default, the format of USB camera is set to RAW.
Peripherals
31
NOTE:
You can optimize performance and modify the frame rate per second, if the Optimize for CPU check box is selected—supported
values include 1/1, 1/2, 1/3, 1/4, 1/5, and 1/6– directly from the thin client (if the webcam supports Universal Video Driver).
This feature is experimental and does not currently support central configuration (INI parameters). Also, this feature is CPU intensive
and is recommended for high performance products such as the Wyse 5010 thin client with ThinOS (D10D), Wyse 3030 LT thin client
with ThinOS and Wyse 3030 LT thin client with PCoIP.
Configuring printer settings
Use the Printer Setup dialog box to configure network printers and local printers that are connected to the thin client. Through its USB
ports, a thin client can support multiple printers. If more than one printer is to be used and another port is not available on your thin client
and the port that is to be used must be shared with a USB modem converter, connect a USB hub to the port.
Configuring peripherals settings on Wyse ThinLinux
On the System Settings page, click the Peripherals icon. The following tabs are displayed on the left pane of the System Settings page.
•
•
•
•
Keyboard
Mouse
Printers
Sound
Setting the keyboard preferences
The Keyboard setting page enables you to set the Keyboard preferences and make the Keyboard layout.
32
Peripherals
NOTE: By default, the Keyboard screen is available in both User mode and Admin mode. Any changes made through Keyboard
preferences screen is saved and continued for the built-in thinuser
Figure 6. Keyboard Preferences
1
Click the ON/OFF button to disable or enable the Key presses repeat when held down option after you log in to the session.
2
Move the slider to the left to decrease the repeated delay time of the pointer or move the slider to the right to increase the repeated
delay time of the pointer.
3
4
5
Move the slider to the left to decrease the repeat rate of the pointer or move the slider to the right to increase the repeat rate of the
pointer.
In the keyboard layout box, select the layout you want to use and click Add to include the preferred layout in the currently added
layouts list.
Select the preferred keyboard layout from the currently added layouts list, and click Set as Default Layout button to set the default
layout.
NOTE: The default keyboard layout is listed on the top of the currently added layout list.
6
Click Save to save your changes.
Setting the mouse preferences
By default, the Mouse screen is available in both User mode and Admin mode. Any changes made through the Mouse preferences screen is
saved and continued for the built-in thinuser.
Peripherals
33
Figure 7. Mouse Preferences
The Mouse setting page enables you to set the Mouse preferences.
1
Click Right or Left to set the primary button of the mouse.
2
Move the slider to the left to increase the speed of the pointer when double-clicked or move the slider to the right to decrease the
length of double-clicked.
3
4
Move the slider to the left to increase the speed of the mouse pointer or move the slider to the right to decrease the speed of the
mouse pointer.
Click Save to save your changes.
Configuring the printer settings
By default, the Printers screen is available only in Admin mode. On the Printer setting page, click the printer icon to start the gnome-
control-center printer.
34
Peripherals
Figure 8. Printer Settings
Figure 9. Add New Printer
1
Click the printer icon.
The gnome-control-center printer dialog box is displayed.
Click Add New Printer button to include the new printer in the printers list available on the left pane.
The Add a new printer window is displayed.
2
3
Enter the address of the printer or the text to filter results.
NOTE: If a USB printer is connected, then it is displayed by default. The printer is not found if wrong address is provided
or the USB is not attached.
4
Click the Add option. Click Print Test Page to test the printer and click (- )icon to remove the printer.
Peripherals
35
Configuring the sound settings
By default, the Sound screen is available in both User mode and Admin mode. Any changes made through Sound screen is saved and
retained for the built-in thinuser.
1
Click the Output tab to configure the audio output settings.
Figure 10. Sound Settings
a
Move the Output volume slider to adjust the output or speaker volume. Click the Output volume button to enable or disable the
output volume.
b
c
Select the device for sound output from the listed output devices. The default audio output is the Analog Output.
Based on the channels available for the selected output device and profile, you can adjust the Balance and Fade values by
moving Balance and Fade sliders respectively.
d
e
Select the audio profile from the drop-down list.
Click the Test Speakers option. A dialog box is displayed. You can perform the speaker testing by playing sample wave files.
2
Click the Input tab to configure the audio input settings.
36
Peripherals
Figure 11. Sound Settings
a
Move the Output volume slider to adjust the output or speaker volume. Click the Output volume option to enable or disable the
output volume.
b
c
Select the device for sound input from the listed input devices. The default audio input is the Analog input.
Move the Input Volume slider to adjust the input or Mic volume. Click the Input volume option to enable or disable the input
volume.
d
The Input level meter bar shows the input volume peak level.
Configuring and using peripherals on WIE10
The thin client device has many ports available on it such as:
•
•
USB Port— 6
DisplayPort — 2
To provide the services through the ports, install the appropriate software for the thin client device.
NOTE:
1
You can install other services and add-ins that are available from the Dell website for free or for a licensing fee.
2
You can configure the thin client device to use Bluetooth- enabled Peripherals. For more information, see Configuring Bluetooth
Configuring Bluetooth connections
You can use your thin client device with other Bluetooth enabled devices, if it has Bluetooth capability.
NOTE:
To retain your settings, disable the Unified Write Filter (UWF) and configure
NetXClean.
Peripherals
37
To configure your thin client for Bluetooth Connections:
1
Log in as an Admin.
2
Click Start Menu > Control Panel > Device Manager.
The Device Manager window is displayed.
3
Expand Bluetooth Radios and double-click any Bluetooth icon. For example, double-click Generic Bluetooth Radio to manage the
existing Bluetooth device. You can also update the drivers in the Update tab.
To add another Bluetooth-enabled device to the thin client device, use the Add a Device wizard.
a
To open the Devices and Printers window, click the Devices and Printers icon in Control Panel.
b
Click Add a Device.
The Add a Device wizard is displayed.
4
Refer to the device documentation and follow the instructions to turn on Bluetooth on the Bluetooth-enabled device. When the device
is discovered by the thin client device, select the device. Click Next and follow the wizard.
38
Peripherals
7
Power state
Wyse 5060 thin client running WES7P.
You can change the power state options of the thin client device by following the steps mentioned here:
1
On the task bar, click the Start button.
From the Start menu, point to the arrow next to the log off button, and then click any one of the following:
2
•
•
Restart— To restart your thin client.
Sleep— This mode enables the power-saving state and allows the thin client to quickly resume full power operations when you
want to start working again.
•
Shut down– Preferred for orderly closing of the operating system.
3
You can also log off the thin client by any of the following ways:
•
•
•
From the Start menu, click log off if you want to log off your thin client.
Press CTRL+ALT+DEL and then click log off.
Press ALT+F4 to log off from the session.
NOTE: If automatic logon is enabled, the thin client will immediately logs on to the default user desktop. We recommend
you use Shut down button to turn off your thin client.
Wyse 5060 thin client running Wyse ThinOS.
Use the Shutdown dialog box to select the available option you want:
•
•
Classic Desktop — Click Shutdown in the Connect Manager or Desktop Menu.
Zero Desktop — Click the Shutdown icon on the Zero Toolbar.
Wyse 5060 thin client running Wyse ThinLinux
On your initial configuration, Dell recommends that you connect by using a wired connection by plugging in the network connected
Ethernet cable to your thin client.
After you turn on your thin client, you are automatically logged in to the thinuser account. By default, the password of the thinuser account
is set to thinuser.
NOTE: In cases where a GDM login is needed (for example, AD/Domain login, PNAgent login and so on), the auto-login option
can be turned off through the GUI or by using the INI.
Admin mode enables you to perform system administration tasks such as adding or removing connections and setting up specific device
settings. To enter into the Admin mode, click the Switch to Admin button from Setting application screen to admin mode and then enter
the default root password in the Password Needed window. The default root password is admin.
Wyse 5060 thin client running WIE10
You can change the power state options of the thin client device by following the steps mentioned here:
1
On the taskbar, click the Start Menu button.
2
Click Power on the start menu, and select any of the options:
•
•
Sleep– This mode uses little power, your thin client device starts up faster.
Shut down– Preferred for orderly closing of the operating system.
Power state
39
•
Restart–The thin client device is turned off and turned on instantly.
You can also use the power state options by pressing the ALT+F4 key combination, and then selecting your preferred option from the drop-
down list.
NOTE:
If automatic logon is enabled, the thin client will immediately log on to the default user desktop.
40
Power state
8
Software
This section describes about establishing and configuring the virtual broker connections for Wyse 5060 thin client.
Topics:
•
•
•
•
Configuring Connections locally on WES7P
When you log in to your thin client as a User, the Windows desktop displays certain notable features.
You can perform the following activities:
•
•
•
Using the Citrix Receiver on WES7P
Citrix Receiver is a server-based computing technology that separates the logic of an application from its user interface. The Citrix
Receiver client software installed on the thin client device allows the user to interact with the application GUI, while all of the application
processes are executed on the server.
Citrix Receiver session services can be made available on the network using either Windows 2008/2012 Server with Terminal Services and
one of the following installed:
•
•
•
•
XenDesktop 7.5
XenDesktop 7.6
XenDesktop 7.8
XenDesktop 7.9
NOTE: If you use a Windows 2003/2008 Server or Citrix XenApp 5.0 with Windows Server 2008, a Terminal Services Client
Access License (TSCAL) server must also be accessible on the network. The server grants a temporary license, which expires
after 120 days. After the temporary license expires, purchase and install the TSCALs on the server. You cannot make a
connection without a temporary or permanent license.
To access the Citrix Receiver session:
•
•
On the thin client Administrator desktop, double-click the Citrix Receiver icon.
Click the Start button on the taskbar, click All Programs, and then click Citrix Receiver on the Programs Menu.
For information about configuring the Citrix receiver, go to www.citrix.com, and then refer to Citrix Documentation.
Software
41
Configuring a remote desktop connection session services on
WES7P
Remote Desktop Connection is a network protocol that provides a graphical interface to connect to another computer over a network
connection.
Use the Remote Desktop Connection dialog box to establish and manage connections to remote applications.
To configure a Remote Desktop Connection:
1
Log in as user or administrator.
2
3
On the taskbar, click the start button, and then click All Programs.
Click Remote Desktop Connection on the Programs menu, and then click Remote Desktop Connection.
The Remote Desktop Connection dialog box is displayed.
You can also double-click the Remote Desktop Connection icon on the desktop to open the Remote Desktop Connection dialog box.
In the Computer box, enter the computer or the domain name. For advanced configuration options, click Show Options.
4
a
In the General tab, you can enter the logon credentials, open an existing RDP connection, or save a new RDP connection file.
b
In the Display tab, manage the display and the color quality of your remote desktop.
•
Move the slider to increase or decrease the size of your remote desktop. To use full screen, move the slider all the way to the
right.
•
•
Select the color quality of your preference for your remote desktop from the drop-down list.
Select or clear the Display the connection bar when I use the full screen check box to display or hide the connection bar in
full screen mode.
c
In the Local Resources tab configure audio, keyboard, or local devices and resources for your remote desktop.
•
•
In the Remote audio section, click Settings for advanced audio settings options.
In the Keyboard section, from the drop-down list select the desired environment you want to apply the keyboard
combinations.
•
In the Local devices and resources section, select devices and resources that you want to use in your remote session. Click
More for more options.
d
e
In the Programs tab, to start a default program with the remote session, select the Start the following program on connection
check box and specify the details.
In the Experience tab optimize the performance of your remote session based on the connection quality.
NOTE: If you find that the File Based Write Filter cache is filling up, you can disable Bitmap caching in the
Experience tab after clicking Show Options in the window.
f
In the Advanced tab, in the Server Authentication section, from the drop-down list, select the action you want the thin client to
perform when the server authentication fails.
In the Connect from anywhere section, click Settings to configure the connection settings such as Remote Desktop Gateway
server settings and logon settings when you are working remotely.
5
6
Click Connect.
Enter the login credentials for connecting to the remote session in the Security dialog box.
NOTE: The standard version (default) is used for a single monitor display, while the Span version can be used when extending a
single session to two monitors for dual-monitor capable thin clients. The Span version can be used when extending a single
session to two monitors for dual-monitor.
42
Software
Configuring a vWorkspace Connection on WES7P
vWorkspace is a concept in which the desktop environment of a computer is separated from the physical computer and hosted as a virtual
workspace on multiple environments, such as a virtual desktop infrastructure (VDI), terminal servers, and/or blade PCs running in a data
center.
Workspace virtualization helps group and deliver a list of applications or desktops together as a single complete virtual workspace. It
isolates and centralizes an entire computing workspace. vWorkspace provides flexible, location and platform independent access by
delivering virtual workspace from multiple virtualization platforms.
To configure a vWorkspace connection:
1
Log in as a user or administrator.
2
On the taskbar, click Start > All Programs > Dell Wyse vWorkspace, or double-click the vWorkspace icon on the desktop.
The vWorkspace window is displayed.
3
4
5
In the vWorkspace window, enter the vWorkspace Server IP, or your registered email address or website address, and then press
Enter.
To retrieve your connector configuration from vWorkspace server, provide the Username, Password, and Domain credentials. Select
the Save Credentials (encrypted) check box if you want to save your login credentials.
Select your preferred vWorkspace Farm location from the following options:
•
•
Inside Office
Outside Office
6
7
Click Connect.
In the Login Credentials dialog box, enter the following credentials to connect to the vWorkspace Farm:
•
•
•
Username
Password
Domain
The vWorkspace Farm screen is displayed.
For more information about managing your vWorkspace connection, go to documents.software.dell.com/vworkspace.
Using VMware Horizon Client on WES7P
VMware Horizon client is a locally installed software application that communicates between View Connection Server and Thin Client OS. It
provides access to centrally hosted virtual desktops from your thin clients. VMware session services can be made available on the network
after you install the VMware Horizon 6. It provides virtualized or hosted desktops and applications through a single platform to end users.
Use the VMware Horizon Client window to connect to a virtual desktop . To open the VMware Horizon Client window, perform either of
the ways mentioned here:
•
•
On the taskbar, click Start > All Programs > VMware > VMware Horizon Client.
Double-click the VMware Horizon Client icon on the desktop.
To use the VMware Horizon Client, follow the guidelines mentioned here:
1
To add a new server, click the New Server button or double-click the Add Server icon in the upper-left corner of the VMware
Horizon Client window.
The VMware Horizon Client dialog box is displayed.
2
In the VMware Horizon Client dialog box, enter the host name or IP address of a View Connection Server in the Connection Server
box, and then click Connect.
3
4
Enter your credentials, and then click Login.
Select a desktop from the list, and then click Connect. VMware Horizon Client connects to the selected desktop. After connection is
established, you can view the client window.
Software
43
For more information, go to www.vmware.com, and refer to the VMware Horizon View Client documentation.
NOTE:
For additional options, click the options icon in the upper-right corner of the VMware Horizon Client window. The available options are
Help, Support information, About VMware Horizon Client, Configure SSL, and Hide the selector after launching an item.
Using Ericom PowerTerm WebConnect
Ericom PowerTerm WebConnect maximizes the value of Terminal Servers (RDS), Virtual desktops (VDI), Web applications, cloud services,
and legacy host systems. For IT departments of all sizes, PowerTerm WebConnect streamlines the management and utilization of IT
resources, while protecting past IT investments and significantly improving the end user-experience.
You can access the Ericom Power Term WebConnect either as a stand-alone application or on a network.
1
Accessing Ericom Power Term WebConnect as a stand-alone:
a
Log in as a user or administrator.
b
Double-click PtStart icon on the desktop.
The Ericom PowerTerm WebConnect window is displayed.
c
d
Enter IP Address in the Server Address field, and click OK.
When you start accessing it for the first time PtStart.exe file is generated and then Power Term WebConnect Login window is
displayed. Else, Power Term WebConnect Login window is displayed.
PtStart.exe file provides the details regarding the server IP address, the folder in which it is installed and the path to reach the
folder.
In the Power Term WebConnect Login window, enter your credentials, and click Login.
Password: ******
DELL – Ericom Application Zone window is displayed.
e
In the DELL – Ericom Application Zone window, published applications such as Blaze demo server, RDP demo server, Ericom
server and Paint are displayed.
Double-click any of these to access them.
You can also add your own applications from the server site.
f
To create a shortcut on your desktop, click Options > Create a shortcut on Desktop in the DELL – Ericom Application Zone
window.
g
To log out, click File > Logout in DELL- Ericom Application Zone window.
2
Accessing Ericom Power Term WebConnect through Web Browser :
a
b
c
Click Internet Explorer icon in the taskbar on Thin Client Administrator desktop.
Internet Explorer web page is displayed.
Enter the URL http://serverIP/FQDNWebConnect6.0/AppPortal/Index.asp to access the Ericom Power Term Emulation.
PowerTerm WebConnect Application Portal page is displayed.
In the PowerTerm WebConnect Application Portal page, enter the credentials and also specify the domain name, then click
Login
For example: Username: administrator
Password: *****
Domain Name
d
e
After you Log in, Published Desktops and Applications such as Blaze demo server, RDP demo server and Paint are displayed.
Double-click any of these to access them on a new Web page.
You can also add your own applications from the server site.
Click Logout on the left side of PowerTerm WebConnect Application Portal page to end the Ericom Power Term WebConnect
session.
44
Software
For more information about Ericom Power Term WebConnect, see www.ericom.com/ericom-connect/enterprise/ and
Configuring the broker setup on Dell Wyse ThinOS
To configure the Broker setup:
1
From the desktop menu, click System Setup, and then click Remote Connections.
The Remote Connections dialog box is displayed.
2
Select Broker type from the drop-down list.
a
If you select None from the list, click either of the following connection protocols:
b
If you select the Citrix Xen, use the following guidelines:
•
•
•
Select the check box to enable the StoreFront style.
Broker Server— Enter the IP address of the Broker Server.
Select the check box to enable automatic reconnection at logon.
NOTE:
If you enable the automatic reconnection, you are able to select from the reconnection options. Click
either of the options where you can connect to the disconnected sessions only or connect to both active
and disconnected sessions.
•
Select the check box to enable automatic reconnection from the button menu.
NOTE: If you enable the automatic reconnection, you are able to select from the reconnection
options. Click either of the options where you can connect to the disconnected sessions only or
connect to both active and disconnected sessions.
Software
45
•
•
•
Account Self-service Server— Enter the IP address of the account self-service server.
XenApp — Use this option, if you want to set default settings to XenApp.
XenDesktop— Use this option, if you want to set default settings to XenDesktop.
c
If you select the VMware View, use the following guidelines:
•
•
Broker Server— Enter the IP address of the Broker server.
Security Mode
— Use this option to select the Security Mode. The available options are Warn on View default, Full security, and No
security.
d
e
If you select the Microsoft, enter the IP address of the broker server in the Broker Server box, and then click OK to save the
settings.
If you select Dell vWorkspace, use the following guidelines:
•
•
•
Broker Server— Enter the IP address of the Broker Server.
Select the check box to enable vWorkspace Gateway.
vWorkspace Gateway— Enter the IP address of the vWorkspace gateway.
f
If you select Other, you must enter the IP address of the broker server in the Broker Server box.
3
Click OK to save the settings.
Configuring connections locally on Dell Wyse
ThinLinux
On the System Settings page, click the Connections icon. The Connections page contains the following tabs:
•
•
Citrix
VMware
NOTE: The description names for all the connections can not be edited once you create the connection.
Configuring and managing Citrix connections
The Citrix Connections page enables you to create and manage the Citrix connections both locally and globally.
46
Software
Figure 12. Citrix connection settings
To configure the local Citrix settings:
1
Click the + icon to add a new Citrix Connection.
The Citrix Connections page is displayed.
2
3
Enter the name of the Citrix connection for which you specify the Server URL address.
From the Connection Type drop-down list, select any of the following connection types:
•
•
•
Server
Published Application
Storefront
4
Click Save to save the changes.
Configuring and managing VMware connections
The VMware connections page enables you to create and manage the View client 3.5 connections.
To configure the VMware Settings, complete the following task:
1
Click the + icon to add a new VMware Connection.
The VMware Connections page is displayed.
Software
47
Figure 13. VMware connections settings
2
3
Enter the name of the VMware connection.
Configure the following options in the Login tab:
Figure 14. VMware login settings
Parameter
Description
Host
Enter the host name or IP address or FQDN of the Horizon of
the VMware View Server.
Port
Enter the port number of the host.
48
Software
Parameter
Description
Protocol
From the drop-down list, select the specific protocol.
Username
Enter the User ID that is used to log in to the remote Horizon
server.
Password
Enter the password that is used to log in to the remote Horizon
server.
Published Application
Click the ON/OFF button to enable or disable this option.
If enabled, specify the Published Application name.
If disabled, specify the Published desktop name.
Enable interactive mode
Click the ON/OFF button to enable or disable this option.
If enabled, then after a successful connection to the server, it
displays all the published application and desktop icons. You can
start the applications or desktop sessions based on your choice.
If disabled, then the Published Applications option is enabled in
the Login tab.
Selecting that option enables you to directly start the application
or desktop that you specify.
Ping before connect
Enable NLA
Click the ON/OFF button to enable or disable this option. If
enabled, it pings the connection is checked in server IP/FQDN
before connecting to a session.
Click the ON/OFF button to enable or disable this option. Enable
the Network Level Authentication (NLA), if NLA is enabled on
your remote computer. Your remote computer requires NLA user
authentication before you establish a full Remote Desktop
connection and the login screen is displayed.
Secure connection
Click the Secure Preferences tab and select any of the options
that determine how the client should proceed when it cannot
verify that your connection to the server is secure.
Domain
Enter the Domain name. It is used to log in the remote Horizon
server.
Desktop
Application
If interactive mode is disabled, you can specify Published desktop
name.
If interactive mode is disabled, you can specify the Published
application name.
4
The following options must be configured in the Experience tab:
Software
49
Figure 15. VMware experience settings
Parameter
Description
Windows resolution
Select the Windows resolution that you want to get the best
display on your monitor. The available resolutions are:
Use All Monitors
Full Screen
Large Screen
Small Screen
1024X768
800X600
640X480
Auto-Reconnect after disconnect.
Click the ON/OFF button to enable or disable this option. If
enabled, the connection is automatically re-established after you
disconnect from the session.
Delay (seconds) before reconnect.
Enable fullscreen
Select the amount of time in seconds to delay the reconnection
attempt after a disconnection occurs.
Click the ON/OFF button to enable or disable this option. Select
this option to view the remote session in full screen mode in all
the monitors.
Disable fullscreen drop-down menu bar
Click the ON/OFF button to enable or disable this option.
50
Software
Parameter
Description
Select this option to disable the drop-down menu bar in the full
screen mode.
Disable exit on the disconnect
Click the ON/OFF button to enable or disable this option.
Select this option if you do not want the Horizon server to retry
connecting if there is a connection error. You can typically select
this option if you use kiosk mode.
Auto-connect after login.
Click the ON/OFF button to enable or disable this option.
Select this option to reconnect automatically after a
disconnection occurs.
Lock server URL/Host field
Click the ON/OFF button to enable or disable this option.
5
Click Save to save the settings.
Configuring connections locally on WIE10
When you log in to your thin client as a User, the Windows desktop displays certain notable features.
You can perform the following activities:
Configuring Citrix Receiver session services on WIE10
Citrix Receiver is a server-based computing technology that separates the logic of an application from its user interface. The Citrix
Receiver client software installed on the thin client device allows the user to interact with the application GUI, while all of the application
processes are executed on the server.
Citrix Receiver session services can be made available on the network using Windows 2008/2012 Server with Terminal Services and one of
the following installed:
•
•
•
•
•
XenDesktop 7.5
XenDesktop 7.6
XenDesktop 7.8
XenDesktop 7.9
XenDesktop 7.11
To install the software, use the instructions accompanying them. Make sessions and applications available to the thin client devices sharing
the server environment.
NOTE:
If you use a Windows 2003/2008 Server or Citrix XenApp 5.0 with Windows Server 2008, a Terminal Services Client Access License
(TSCAL) server must also be accessible on the network. The server grants a temporary license, which expires after 120 days. After the
temporary license expires, purchase and install the TSCALs on the server. You cannot make a connection without a temporary or
permanent license.
To configure a Citrix Receiver session:
1
Log in as an admin.
2
Access the Citrix Server using one of the following options:
•
•
From the Start Menu, click Citrix Receiver.
Double-click the Citrix Receiver icon on the desktop.
After you log in to the Citrix Server, the Add Account window is displayed.
Software
51
3
In the Add Account window, enter the Server IP address and then click Next.
•
•
For secure connections, enter Fully Qualified Domain Name (FQDN).
For non-secure connections, enter the IP address.
4
5
6
7
Enter the user credentials and then click Log on.
You can add an account by providing the IP address and you can view the details of the Citrix Receiver.
Click Yes and then click Next.
The Virtual desktop of the Citrix Receiver is displayed.
In the Virtual desktop window, click Add Apps (+) > All Applications.
You can select or clear the application check -boxes. The selected applications are displayed on the virtual desktop.
On the virtual desktop, click Settings to:
•
•
•
Refresh
Add or Delete Server account
Log-off
Configuring the Remote Desktop Connection session services
on WIE10
Remote Desktop Connection is a network protocol that provides a graphical interface to connect to another computer over a network
connection.
To install the software, use the instructions accompanying them. Make sessions and applications available to the thin client devices sharing
the server environment.
NOTE: If you use a Windows 2003/2008 Server or with Windows Server 2008, a Terminal Services Client Access License
(TSCAL) server must also be accessible on the network. The server grants a temporary license, which expires after 120 days.
After the temporary license expires, purchase and install the TSCALs on the server. You cannot make a connection without a
temporary or permanent license.
To configure a Remote Desktop Connection:
1
Log in as a user or administrator.
2
From the Start menu, click Remote Desktop Connection, or double-click the Remote Desktop Connection icon on the desktop.
The Remote Desktop Connection window is displayed.
3
In the Computer box, enter the computer or the domain name.
For advanced configuration options, click Show Options.
a
In the General tab, you can enter the logon credentials, edit or open an existing RDP connection, or save a new RDP connection
file.
b
In the Display tab, manage the display and the color quality of your remote desktop.
•
Move the slider to increase or decrease the size of your remote desktop. To use full screen, move the slider all the way to the
right.
•
•
Select the color quality of your preference for your remote desktop from the drop-down list.
Select or clear the Display the connection bar when I use the full screen check box to display or hide the connection bar in
full screen mode.
c
d
In the Local Resources tab configure audio, keyboard, or local devices and resources for your remote desktop.
•
•
•
In the Remote audio section, click Settings for advanced audio settings options.
In the Keyboard section, choose when and where to apply keyboard combinations.
In the Local devices and resources section, select devices and resources that you want to use in your remote session. Click
More for more options.
In the Experience tab optimize the performance of your remote session based on the connection quality.
52
Software
NOTE:
If you find that the Unified Write Filter cache is filling up, you can disable Bitmap caching in the Experience tab
after clicking Show Options in the window.
e
In the Advanced tab, select the action to be taken when the server authentication fails and configure settings for connection
through Remote Gateway.
4
5
Click Connect.
Enter the login credentials for connecting to the remote session in the Security dialog box.
The remote desktop is displayed with the connection bar on the top if you select the Display the connection bar option in step 3 b.
Configuring vWorkspace connection on WIE10
vWorkspace is a concept in which the desktop environment of a computer is separated from the physical computer and hosted as a virtual
workspace on multiple environments, such as a virtual desktop infrastructure (VDI), terminal servers, and/or blade PCs running in a data
center.
Workspace virtualization helps group and deliver a list of applications or desktops together as a single complete virtual workspace. It
isolates and centralizes an entire computing workspace. vWorkspace provides flexible, location and platform independent access by
delivering virtual workspace from multiple virtualization platforms.
To configure a vWorkspace connection:
1
Log in as a user or administrator.
2
On the Start Menu, click Dell Wyse vWorkspace, or double-click the vWorkspace icon on the desktop.
The vWorkspace window is displayed.
3
4
5
In the vWorkspace window, enter the vWorkspace Server IP, or your registered email address or website address, and then press
Enter.
To retrieve your connector configuration from vWorkspace server, provide the Username, Password, and Domain credentials. Select
the Save Credentials (encrypted) check box if you want to save your login credentials.
Select your preferred vWorkspace Farm location from the following options:
•
•
Inside Office
Outside Office
6
7
Click Connect.
In the Login Credentials dialog box, enter the following credentials to connect to the vWorkspace Farm:
•
•
•
Username
Password
Domain
The vWorkspace Farm screen is displayed.
For more information about managing your vWorkspace connection, go to documents.software.dell.com/vworkspace.
Using VMware Horizon Client on WIE10
VMware Horizon Client is a locally installed software application that communicates between View Connection Server and thin client OS. It
provides access to centrally hosted virtual desktops from your thin clients.
VMware session services can be made available on the network after you install the VMware Horizon 6. It provides virtualized or hosted
desktops and applications through a single platform to end users.
To connect to a virtual desktop, use the VMware Horizon Client window.
To open and use the VMware Horizon client window:
1
Log in as a user or administrator.
2
Access the VMware Horizon client window using one of the following options:
Software
53
•
•
From the Start Menu, click VMware > VMware Horizon Client.
Double-click the VMware Horizon client icon on the desktop.
The VMware Horizon client window is displayed.
3
In the VMware Horizon client window, use the following guidelines:
a
To add a new server connection, either click the New Server option or double-click the Add Server icon in the VMware Horizon
client window.
The VMware Horizon client dialog box is displayed.
b
In the VMware Horizon Client dialog box, type a host name or an IP address of a VMware Horizon Connection Server in the
connection server box.
c
d
e
f
Click Connect.
In the Login dialog box, enter the user name and login password in the respective boxes.
From the Domain drop-down list, select the domain where the server is located.
Click Login.
The VMware Horizon Client connects to the selected desktop. After connection is established, the list of published desktop is
displayed.
g
Right-click the particular application or desktop icon, and then click Launch to connect to that application or desktop.
NOTE:
Certificate checking mode— Certificate checking mode determines how the client proceeds when the client cannot verify
that your connection to the server is secure. We recommend that you do not change this setting unless instructed to do so
by your system administrator.
To access the certificate checking mode, click the icon on the upper-right corner of the window, and then click Configure
SSL from the drop-down list. In the VMware Horizon client SSL configuration dialog box, select from any of the following
options based on your requirements:
•
•
•
Never connect to untrusted servers
Warn before connecting to untrusted servers
Do not verify server identify certificates
Using Ericom Connect-WebConnect client on WIE10
You can access the Ericom Connect-WebConnect client either as a stand-alone application or on a network.
1
Accessing Ericom Connect-WebConnect Client as a stand-alone:
a
Log in as a user or administrator.
b
From the Start Menu, click Ericom Connect-WebConnect client > Ericom Connect-WebConnect client or double-click the
Ericom Connect-WebConnect client icon on the desktop.
The Ericom AccessPad login window is displayed.
c
In the Ericom AccessPad Login window, enter your credentials, and click Login.
Password: ******
DELL – Ericom Application Zone window is displayed.
NOTE: By default, the Ericom AccessPad login window is displayed in English (US) language. To set the UI
to your preferred language, click the Globe icon in the lower-right corner of the window, and select your
preferred language from the drop-down list.
d
In the DELL – Ericom Application Zone window, published applications such as Blaze demo server, RDP demo server, Ericom
server and Paint are displayed.
Double-click any of these to access them.
54
Software
You can also add your own applications from the server site.
e
f
To create a shortcut on your desktop, click Options > Create a shortcut on Desktop in the DELL – Ericom Application Zone
window.
To log out, click File > Logout in DELL- Ericom Application Zone window.
2
Accessing the Ericom Connect-WebConnect client through Web Browser:
a
b
c
Double-click the Internet Explorer icon.
The Internet Explorer web page is displayed.
Enter the URL http://serverIP/FQDNWebConnect6.0/AppPortal/Index.asp to access the Ericom Power Term Emulation.
The PowerTerm WebConnect Application Portal page is displayed.
In the PowerTerm WebConnect Application Portal page, enter the credentials and also specify the domain name, then click
Login.
For example: Username: administrator
Password: *****
Domain Name
d
e
After you Log in, Published Desktops and Applications such as Blaze demo server, RDP demo server and Paint are displayed.
Double-click any of these to access them on a new web page.
You can also add your own applications from the server site.
Click Logout on the left side of PowerTerm WebConnect Application Portal page to end the Ericom Power Term WebConnect
session.
Software
55
9
Management interface of Dell Wyse 5060 thin
client
This section describes about the management interface of Dell Wyse 5060 thin client.
Topics:
•
•
•
•
Wyse Device Manager (WDM) software for remote
administration
WDM servers provide network management services to the thin client complete user-desktop control—with features such as remote
shadow, reboot, shutdown, boot, rename, automatic device check-in support, Wake-On-LAN, change device properties, and so on. With
WDM you can manage all of your network devices from one simple-to-use console.
Configuring WDA settings on WES7P/WIE10
Wyse Device Agent allows you to configure/register the client to connect to WDM /CCM server and performs auto discovery for searching
the available management server in the order of WDM and CCM.
The following are three types of registrations in WDA:
•
•
•
Auto Discovery
WDM Registration
CCM Registration
Auto Discovery
If you selects Auto Discovery option from the following WDA UI, it allows the WDA to search for all the available management servers and
register the thin client on the respective server in the order of WDM and CCM.
56
Management interface of Dell Wyse 5060 thin client
Figure 16. Auto discovery
It searches in the order of WDM and CCM and gets connected to the management server which is available.
Configuring WDM using WDA
Wyse Device Agent allows you to configure/register to WDM server.
In the below WDA UI, complete the following task:
Figure 17. Device registration
1
Enter the IP address or FQDN of WDM server.
Management interface of Dell Wyse 5060 thin client
57
2
3
Click the On/Off button to enable or disable preferred type of server.
Enter the WDM server port number in the HTTPS port field. The default value is 443.
NOTE: Whenever Client is registered to a WDM server, all the details that are configured for discovery is taken from
the server.
4
To connect with WDA Management Server, WDA supports the following types of discoveries:
•
•
•
•
DNS Hostname discovery
DNS SRV discovery
DHCP Option Tags
Manual discover from WDM
The WDA Agent works with the WDM services on the WDM server to perform the required actions.
The WDM Agent understands the commands sent by the WDM server and makes the necessary changes.
The WDM Agent provides status updates about the device.
Configuring CCM using WDA
WDA allows you to get registered to CCM server if you select the CCM option from the drop-down list.
Figure 18. Device registration
1
Enter the IP address of the CCM management server.
Enter the CCM server port number in the provided field.
Enter the MQTT server details in the provided field.
Enter the Group Token details in the provided field.
2
3
4
NOTE: WDA supports only the DHCP discovery for CCM server.
Configuring the WDA settings on Dell Wyse ThinOS
Use this tab to configure the WDM and CCM settings.
58
Management interface of Dell Wyse 5060 thin client
To configure the WDA settings, do the following:
1
From the desktop menu, click System Setup, and then click Central Configuration.
The Central Configuration dialog box is displayed.
2
Click WDA, and use the following guidelines.
WDM is selected by default. WDA service automatically runs after the client starts up.
If the first discovery, for example, the WDM service is not successful, then it seeks for the next priority, for example, CCM service.
This continues till a discovery is successful. If all discoveries fail, then it is started again automatically after a fixed time (24 hours).
a
WDM Servers — Enter the IP addresses or host names, if WDM is used. Locations can also be supplied through user profiles, if
user INI profiles are used.
b
DNS Name Record — (Dynamic Discovery) Allows devices to use the DNS host name lookup method to discover a WDM
server.
c
d
DHCP Inform — (Dynamic Discovery) Allows devices to use DHCP inform to discover a WDM Server.
Enable Automatic Discovery After Missed Check-ins — Select the number of missed check-ins after which you want the auto
discovery options enabled.
3
Click OK to save the settings.
Service checked in status is displayed in System Information.
Management interface of Dell Wyse 5060 thin client
59
The following is the INI parameter for this feature:
WDAService={yes(default),no}Priority ={WDM(default),CCM,“WDM;CCM”,“CCM;WDM”}
To configure the CCM settings, do the following:
1
Click CCM, and use the following guidelines.
a
Enable Cloud Client Manager (CCM) — Select the check box to enable the Cloud Client Manager(CCM).
60
Management interface of Dell Wyse 5060 thin client
b
Group Registration Key — Enter the Group Registration Key as configured by your cloud Client Manager administrator for the
desired group.
NOTE: If you enable the Cloud Client Manager (CCM ), make sure that you have entered the Group Registration Key
and enabled the CCM Advanced Settings.
2
Click OK to save the settings.
Configuring the WDA settings on Dell Wyse ThinLinux
The Wyse Device Agent (WDA) on the ThinLinux device supports only the features of Cloud Client Manager (CCM) device management
solution. Wyse Device Agent is for configuring the CCM (Cloud Client Manager) client settings and registering a ThinLinux device into CCM
and it is available only for admin user.
Management interface of Dell Wyse 5060 thin client
61
Figure 19. Wyse Device Agent (CCM)
If the device is not registered to a CCM server, the Wyse Device Agent screen shows the registration status as Not Registered.
1
In the CCM Server input box, enter the URL of CCM server you want to connect to.
2
3
In the MQTT Server input box, enter the IP address or hostname of Message Queue Telemetry Transport (MQTT) server.
In the Group Token input boxes, enter your group registration key to manage your ThinLinux device. This is a unique key for registering
your thin client device. Thin clients can be directly registered to Groups directly and must have a Group Registration Key enabled to
perform this action.
4
Do one of the following options:
•
Click Register to register your thin client on CCM server. When your thin client is successfully registered, the status is shown as
Registered with green color icon next to the Registration Status label, and caption of Register button changes to Unregister.
•
Click Unregister, if you want to remove your thin client from the CCM management system. If Unregister fails, a dialog box for
Force Unregister confirmation is displayed. Click Yes to forcefully unregister your device which is managed by CCM. When you
perform Register or Unregister or Force Unregister from Agent screen, the applet should not be closed until Registration Status.
After successful registration, you can access the CCM management server screen where you can view and manage Device Asset
Details, Real-Time commands, and Troubleshooting information of your registered thin client.
Directing the Thin Client to CCM Server:
•
To direct your thin client to CCM server, you must provide CCM/MQTT server details and Group registration Key. These details is
discovered by Wyse Device Agent using any of the following ways:
•
•
•
DHCP Scope options
Using INI parameter
Using the Wyse Device Agent screen
•
Directing the thin client to CCM Server using DHCP Scope options. The CCM/MQTT server details and Group Registration Key
that are required for CCM registration can be obtained by querying the DHCP server with following option tags:
•
•
•
199 – Scope option for Group Token (type = String, value = CCM-group-key).
165 – Scope option for CCM server.
166 – Scope option for MQTT server.
•
Directing the thin client to CCM Server using INI parameters, INI syntax for CCM configuration:
•
CCMEnable={yes,no} CCMServer=<CCM Server URL> GroupRegistrationKey=<tenant code-group code>
MQTTServer=<MQTT server>[:<MQTT port>]
62
Management interface of Dell Wyse 5060 thin client
NOTE:
When INI discovery method is used for registering the device, if you want to unregister the device, you must delete the INI
parameters and restart the device first and then unregister the device. Else you have to perform the unregister process twice. For
more information, see ThinLinux INI Guide .
Management interface of Dell Wyse 5060 thin client
63
10
System specifications
Table 8. Brand/Sub-brand/Model Number/Chassis description/Series Level/Category Type
Features
Specification
Ambient operation
0 to 35 degree Celsius (32 to 95 degree F)
-40 to 65 degree Celsius (-40 to 149 degree Fahrenheit)
20% to 80% (non condensing)
-15.2 to 3048m (-50 to 10,000 ft)
Yes
Non-operation temperature
Humidity
Max Altitude
OEM Ready
Table 9. Processor/chipset
Features
Specification
SOC-AMD
Steppe Eagle
CPU core
AMD steppe Eagle GX-424 (2.4 GHz Quad Core) (TDP @ 15W
adjusted by BIOS)
Graphics
TPM
AMD integrated graphics Radeon R5E
Version 1.2 0r 2.0 (option; FW configurable).
Table 10. Memory
Features
Description
System memory
•
•
4 GB/ 8 GB DDR3 1600MHz(2*SO-DIMM)
8 GB (WES7P and WIE10)
storage
8GB/64GB SATA3 flash module only.
Network
WLAN+BT Combo Module: Intel 7265 M.22230(PCIe/USB
interface)
Table 11. I/O (front)
Features
Specification
LEDs
•
•
1*Power button (blue color)
1*Power button (bi-color)
USB 2.0
Audio
2*USB 2.0
1*Audio combo jack
64
System specifications
Table 12. I/O (rear)
Features
Specification
Antenna
2*Antenna (2T2R) option
USB 2.0
2*USB 2.0 (stacked)
USB 3.0
2*USB 3.0 (stacked)
Display Port
2*DP
Physical security
RJ 45 Ethernet
SFP interface RTL8211FS
1*Kensington Lock Slot
1 * RJ-45 (10/100 /1000 Base-T Ethernet)
Realtek RTL8111HN+8211FS
Table 13. Form factor
Features
Specification
Chassis leveraged
Dell Wyse 5020 (Oberon)
Chassis access
Sealed chassis, accessible with tools
Optional mounting
Height(Z)mm
Wall mount / vesa mount
40
Width(x)mm
185
Depth(Y)mm
170
Weight (pounds / kilograms)
Total no of HDDs/SDDs supported
0.93kg (2.05 lb)
0
Table 14. Power requirement
Features
Specification
AC input voltage range (comply with L.P.S)
19V 65W
Table 15. BIOS
Features
Specification
Standard BIOS, UEFI as implemented using Phoenix UEFI
Y
Support Wake-On-LAN
Y
Table 16. Operating system
Features
Specification
OS and system software
•
•
•
•
ThinLinux
ThinOS
WES7P
Windows 10 IoT Enterprise(downgraded to WES7P)
System specifications
65
66
System specifications
11
Troubleshooting your system
You can troubleshoot your system using indicators like diagnostic lights, and error messages during the operation of the device.
Topics:
•
•
Power states and LED behavior
Table 17. Power states and LED behavior
States
Behavior
Indicators
•
•
•
Power LED: Blue
Activity LED: Bi-color, Green/Amber
Power state:
•
•
•
S0–On: Power LED Blue, Activity LED green
S3 – Standby/Sleep: Power LED off, Activity LED blinking.
S5 – Off: All LED off
•
Operation State:
•
•
Boot: Power LED on, Activity LED.
In O/S: Power LED on, Activity LED green
Power button control
•
•
On/Off-state detection: Push power button is < 4s
Force Off-state: Push and hold power button is >= 4s
Diagnostic power LED codes
Table 18. Diagnostic power LED codes
Power LED light status
Possible cause
Troubleshooting steps
Both power LED and activity LED come up
briefly and then turn off.
At first power apply :No LED light up briefly
•
Check AC power, call your utility
company
•
•
Check AC power cord is plug-in
Check DC plug is plug into the unit
At first power apply : Both LED stay ON
Both power LED and activity LED come up
briefly and then turn off
•
•
•
Logic board defect
BIOS malfunctioning
Abnormal power source
Push power button the LED does not turn
•
Power LED should come up in steady
BLUE
•
•
Logic board defect
Power button defect
Troubleshooting your system
67
Power LED light status
Possible cause
Troubleshooting steps
•
Activity LED should turn on in steady
AMBER
•
Mechanical assembly misalign cause
miss actuation
68
Troubleshooting your system
|