CopyCentre C20
WorkCentre M20/M20i
User Guide
604E07110
Table of Contents
Safety.......................................................................................................... 1-6
Regulations - Canada.............................................................................. 1-17
Installing Software................................................................................... 2-23
Using Interrupt......................................................................................... 3-14
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page i
Setting the Paper Size............................................................................... 4-8
Dialing Methods......................................................................................... 6-6
Basic Fax Features.................................................................................... 6-8
Special Fax Features............................................................................... 6-10
Fax Setup Options................................................................................... 6-19
Printer Settings.......................................................................................... 7-3
Page ii
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Clear Memory........................................................................................... 9-24
Fault Clearance........................................................................................ 11-3
General Specifications............................................................................ 12-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page iii
Page iv
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
1 Welcome
Thank you for choosing the Xerox CopyCentre C20,
WorkCentre M20 or WorkCentre M20i. These products have
been designed for ease of use, but to use your machine to its
fullest potential take some time to read the User Guide.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 1-1
Introduction
The Xerox CopyCentre C20, WorkCentre M20 or WorkCentre M20i are a family of digital
devices capable of being used for copying, printing, faxing, scanning and e-mail. The features
and functions available on your machine depend on the model purchased:
Xerox CopyCentre C20
This model is a digital copier and copies at 21 pages per minute. It comes with a Document
Feeder, Paper Tray and Bypass Tray as standard and also provides 2 Sided copying.
An additional Paper Tray, Foreign Interface, Cabinet and Stand are available as options.
Xerox WorkCentre M20
This model provides digital copying, direct printing and direct scanning. It copies and prints at
21 pages per minute. A Document Feeder, Paper Tray and Bypass Tray are also provided
and 2 Sided copying and printing is supported.
An additional Paper Tray, a Foreign Interface, a Cabinet and Stand and Network Printing are
available as options.
Xerox WorkCentre M20i
This model has digital copying, direct scanning, and faxing capabilities. It also provides
networked printing and e-mail.
A Document Feeder and a single Paper Tray are supplied as standard, and 2 Sided capability
is also supported. An additional Paper Tray, a Foreign Interface, and a Cabinet and Stand are
available as options.
Documentation and software is provided to support the networked capability and an additional
32MB memory is supplied with the e-mail function.
z For instructions
on unpacking and
setting up the
machinereadyfor
use the Quick
Install Sheets, or
Page 1-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
About This Guide
Throughout this User Guide some terms are used interchangeably:
¾ Paper is synonymous with media.
¾ Document is synonymous with original.
¾ Xerox CopyCentre C20, WorkCentre M20 or WorkCentre M20i is synonymous with the
machine.
The following table offers further information about the conventions used within this Guide.
CONVENTION
Italic Typeface
DESCRIPTION
EXAMPLE
Xerox CopyCentre C20, WorkCentre
M20 or WorkCentre M20i.
Used to emphasise a word or phrase.
In addition, references to other
publications are displayed in Italic
typeface.
Bracket Text Typeface
Notes
Used to emphasise the selection of a ¾ Select the paper supply source
feature mode or key.
required by pressing [Paper
Supply].
z For instructions on loading media, refer
Located in the margins and used to
provide additional or useful
information about a function or
feature.
Specification Note
Caution
Provides more in-depth specification
information relating to the machine.
L
For full media specifications refer to
Cautions are statements that suggest
mechanical damage as a result of an
action.
CAUTION: DO NOT use organic or
strong chemical solvents or
aerosol cleaners or pour fluids
directly onto any area.
Warning
Used to alert users to the possibility of
personal injury.
WARNING: This product must be
connected to a protective earthing
circuit.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 1-3
Related Information Sources
Information available for the products consists of:
- This User Guide
- The Quick Start Guide
- The Quick Install Sheets
- The System Administration Guide
- The Xerox website http://www.xerox.com
Page 1-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Customer Support
If you need assistance during or after product installation, please visit the Xerox website for
online solutions and support:
http://www.xerox.com
If you require further assistance, call our experts at the Xerox Welcome Center, or contact your
local representative. When telephoning please quote the machine serial number. Use the
space below to make a note of the machine serial number:
# ____________________________________________
To access the serial number open the side cover using the release latch and then open the
front door. The serial number is located on the panel above the Toner Cartridge.
The Xerox Welcome Center or local representative telephone number is provided when the
machine is installed. For convenience and future reference, please record the telephone
number in the space below:
Xerox Welcome Center or local representative telephone number:
# ____________________________________________
Xerox US Welcome Center:1-800-821-2797
Xerox Canada Welcome Center:1-800-93-XEROX (1-800-939-3769)
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 1-5
Safety
Your Xerox product and supplies have been designed and tested to meet strict safety
requirements. These include Safety Agency approval, and compliance to established
environmental standards. Please read the following instructions carefully before operating the
product and refer to them as needed to ensure the continued safe operation of your product.
The safety testing and performance of this product have been verified using XEROX materials
only.
Follow all warnings and instructions marked on, or supplied with the product.
This WARNING Mark alerts users to the possibility of personal injury.
This WARNING Mark alerts users to heated surfaces.
WARNING: This product must be connected to a protective earthing circuit.
This product is equipped with a 3-wire type plug, provided with a protective earthing pin. This
plug will fit only into an earthed power outlet. This is a safety feature. To avoid risk of electric
shock, contact your electrician to replace the receptacle if you are unable to insert the plug
into the outlet. Never use an earthed adapter plug to connect the product to a power source
receptacle that lacks an earth connection terminal.
This product should be operated from the type of power source indicated on the marking
label. If you are not sure of the type of power available, consult your local power company.
Do not allow anything to rest on the power cord. Do not locate the product where persons will
step or trip on the cord.
Use of an extension cord with this product is not recommended or authorized. Users
should check building codes and insurance requirements if a properly earthed extension cord
is to be used. Ensure that the total ampere ratings of the products plugged into the extension
cord do not exceed the extension cord ampere rating. Also, ensure that the total amperage of
all products plugged into the wall outlets does not exceed the outlet rating.
Disconnect Device for this product is the power cord. To remove all electrical power to the
product, disconnect the power cord from the power receptacle.
Your equipment is equipped with an energy saving device to conserve power when the
machine is not in use. The machine may be left on continuously.
Unplug this product from the wall outlet before cleaning. Always use materials specifically
designated for this product. Use of other materials may result in poor performance and could
create a hazardous situation.
Page 1-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Do not use aerosol cleaners. Follow the instructions in this User Guide for proper cleaning
methods.
Never use supplies or cleaning materials for purposes other than those for which they were
intended. Keep all supplies and materials out of reach of children.
Do not use this product near water, wet locations, or outdoors.
Do not place this product on an unstable cart, stand or table. The product may fall, causing
personal injury or serious damage to the product
Slots and Openings in the cabinet and in the back and sides of the product are provided for
ventilation. To ensure reliable operation of the product and to protect it from overheating, these
openings must not be blocked or covered. The product should never be located near or over
a radiator or heat register. This product should not be placed in a built-in installation unless
proper ventilation is provided.
Never push objects of any kind into the slots of the product as they may touch dangerous
voltage points or short out parts which could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Never remove covers or guards that require a tool for removal, unless directed to do so in a
Xerox approved maintenance kit.
Never defeat interlock switches. Machines are designed to restrict operator access to unsafe
areas. Covers, guards and interlock switches are provided to ensure that the machine will
not operate with covers opened.
Do not put your hands into the fuser area, located just inside the exit tray area, as you may
be burned.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instruction.
Quality Standards: The product is manufactured under a registered ISO9002 Quality system.
If you need additional safety information concerning this XEROX product or XEROX supplied
materials you may call the following number:
EUROPE +44 (0) 1707 353434
USA/CANADA 1 800 828 6571
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 1-7
Safety Standards
EUROPE This XEROX product is certified by the following Agency using the Safety Standards listed.
Agency: TUV Rheinland
Standard: IEC60950 3rd Edition Amendments A1, A2, A3, A4 and A11.
USA/CANADA This XEROX product is certified by the following Agency using the Safety Standards listed.
Agency: UNDERWRITERS LABORATORIES
Standard: UL 60950 3rd Edition. Certification is based on reciprocity agreements, which
include requirements for Canada.
Page 1-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Regulatory Information
The CE marking applied to this product symbolizes Xerox Limited Declaration of Conformity
with the following applicable Directives of the European Union as of the dates indicated:
January 1, 1995: Council Directive 73/23/EEC amended by Council Directive 93/68/EEC, approximation of the
laws of the member states related to low voltage equipment.
January 1, 1996: Council Directive 89/336/EEC, approximation of the laws of the member states related to
electromagnetic compatibility.
March 9, 1999 Council Directive 99/5/EC, on radio equipment and telecommunications terminal equipment
and the mutual recognition of their conformity.
A full declaration, defining the relevant directives and referenced standards can be obtained
from your Xerox representative or by contacting:
Environment, Health and Safety
Xerox Limited
Bessemer Road
Welwyn Garden City
Hertfordshire
AL7 1HE
England
Telephone Number: +44 (0) 1707 353434
WARNING: This is a Class A product. In a domestic environment this product may
cause radio frequency interference, in which case the user may be required to take
adequate measures.
WARNING: This product is certified manufactured and tested in compliance with strict
safety and radio frequency interference regulations. Any unauthorized alteration
which includes the addition of new functions or the connection of external devices
may impact this certification. Please contact your local XEROX Limited representative
for a list of approved accessories.
WARNING: In order to allow this equipment to operate in proximity to Industrial,
Scientific and Medical (ISM) equipment, the external radiation from the ISM equipment
may have limited or special mitigation measures taken.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 1-9
WARNING: Shielded cables must be used with this equipment to maintain compliance
with Council Directive 89/336/EEC.
FCC Part 15 This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the product is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Reference CFR Changes or modifications to this equipment not specifically approved by the XEROX
47 Part 15
Corporation may void the user's authority to operate this equipment.
Section 15.21
Shielded cables must be used with this equipment to maintain compliance with FCC
regulations.
Laser Safety
WARNING: Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
With specific regard to lasers, the equipment complies with laser product performance
standards set by governmental, national and international agencies as a Class 1 Laser
Product. It does not emit hazardous radiation as the beam is totally enclosed during all phases
of customer operation and maintenance.
Page 1-10
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
The Electricity at Work Regulations - UK ONLY
The Electricity at Work Regulation 1989 came into force in England and Wales on 1 April 1990.
This 1989 Regulation places a duty on all employers and self-employed persons to ensure the
electrical system in their premises is constructed, maintained and operated in such a manner
as to prevent, so far as reasonably practical, danger. This includes ensuring all electrical
equipment connected to such electrical systems safely constructed, maintained and operated.
All Xerox equipment has been designed to exacting safety standards and has undergone a
variety of stringent safety tests including earth bond, insulation resistance and electrical
strength tests. Xerox Limited manufacturing plants have been awarded ISO 9000 quality
certification and are subject to regular audits by the British Standards Institution or equivalent
national standards body.
Xerox equipment which has been properly and regularly serviced and maintained should not
have to undergo additional specific safety tests pursuant to the 1989 Regulation. Customers
advice prior to any test implementation.
XEROX equipment should, however, be properly and regularly serviced and maintained at all
times.
QUESTION:
ANSWER:
What is the Electricity at Work Regulation?
The Electricity at Work Regulation 1989 came into force in England and
Wales on 1 April 1990. This 1989 Regulation places a duty on all employers and self-
employed persons to ensure the electrical systems in their premises are constructed,
maintained and operated in such a manner as to prevent, so far as reasonably practicable,
danger. This includes ensuring that all electrical products connected to such electrical systems
are safely constructed, maintained and operated.
QUESTION:
ANSWER:
Does XEROX Limited comply with the Electricity at Work Regulation?
The regulation places a duty on all employers and self-employed persons
to ensure the electrical systems in their premises are, effectively safe.
The regulation does not impose on, amongst others, manufacturers or suppliers of such
electrical systems. However, rest assured that all XEROX equipment which XEROX Limited
and its authorized distributors supplies to customers, conforms with all the relevant safety
legislation and standards.
QUESTION:
ANSWER:
Is XEROX equipment safe?
All XEROX equipment supplied by XEROX Limited and their authorized
distributors conforms to all relevant safety legislation and standards.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 1-11
QUESTION:
ANSWER:
Is the XEROX equipment in my premises safe?
All XEROX equipment supplied by XEROX Limited and their authorized
distributors conforms to all relevant safety legislation and standards. However, like all
electrical equipment, they have to be regularly serviced and maintained by competent
persons.
XEROX Limited Customer Service Engineers ensure XEROX equipment is serviced and
maintained to exacting XEROX safety standards. If you would like your XEROX equipment to
be serviced and maintained to such high standards, please contact your local XEROX Limited
Customer Service Organization. They will be pleased to assist you.
QUESTION:
Does the XEROX equipment in my premises comply with the Electricity
at Work Regulations?
ANSWER:
All employers and self-employed persons must ensure that the electrical
systems in their premises are safe. This will include ensuring XEROX equipment in such
premises is safe.
XEROX Limited’s Product Safety function has prepared a guide which contains a list of tests
which may be completed by your XEROX Limited Customer Service Organization.
THESE TESTS MUST BE CARRIED OUT ONLY BY PERSONS WHO POSSESS THE
RELEVANT SKILL, KNOWLEDGE AND EXPERIENCE TO CARRY OUT SUCH TESTS.
Please contact the XEROX Limited Customer Service Organization for further information.
THE USE OF INAPPROPRIATE TEST PROCEDURES AND TEST EQUIPMENT MAY
PROVIDE MISLEADING RESULTS AND MAY CAUSE DEATH, PERSONAL INJURY AND/
OR DAMAGE TO PROPERTY.
QUESTION:
I would like to carry out my own safety tests on the XEROX equipment
in my premises.
ANSWER:
You may, of course, request such tests as you deem necessary to satisfy
yourself that your XEROX equipment is safe. Your XEROX Limited Customer Support will be
pleased to advise you on such testing.
QUESTION:
ANSWER:
I require records of all tests.
After safety testing, your XEROX Limited Customer Service Engineer will
provide you with a certificate which details the results of all tests completed.
Page 1-12
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
In the event of any defect being noted, the XEROX equipment will be switched off and
disconnected from the supply until the defect has been corrected. You will be advised of such
action to enable such defects to be corrected.
PLEASE NOTE: YOU MUST ENSURE THAT YOUR XEROX EQUIPMENT IS SAFE AT ALL
TIMES.
Please contact us if you have any queries regarding the information provided in this document.
Environment, Health and Safety
XEROX Limited
Bessemer Road
Welwyn Garden City
Hertfordshire
AL7 1HE
England
Telephone Number: +44 (0) 1707 353434
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 1-13
Regulations - Europe
Certification to 1999/5/EC Radio Equipment & Telecommunications
Terminal Equipment Directive
This Xerox product has been self-certified by Xerox for pan-European single terminal
connection to the analogue public switched telephone network (PSTN) in accordance with
Directive 1999/5/EC.
The product has been designed to work with the national PSTNs and compatible PBXs of the
following countries:
Austria
Belgium
Denmark
France
Italy
GermanyLuxembourg
GreeceNetherlands
IcelandNorway
IrelandPortugal
Spain
Sweden
Switzerland
United Kingdom
Finland
In the event of problems, you should contact your local Xerox representative in the first
instance.
This product has been tested to and is compliant with TBR21, a technical specification for
terminal equipment for use on analogue-switched telephone networks in the European
Economic Area.
The product may be configured to be compatible with other country networks. Please contact
your Xerox representative if it needs to be reconnected to another country's network. There
are no user-adjustable settings in the product.
NOTE: Although this product can use either loop disconnect (pulse) or DTMF (tone) signaling it is
recommended that it is set to use DTMF signaling. DTMF signaling provides reliable and faster call set-
up.
Modification, connection to external control software or to external control apparatus not
authorized by Xerox, will invalidate its certification.
Page 1-14
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Regulations - USA
Fax Send Header Requirements
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a
computer or other electronic device, including Fax machines, to send any message unless
such message clearly contains in a margin at the top or bottom of each transmitted page or
on the first page of the transmission, the date and time it is sent and an identification of the
business or other entity, or other individual sending the message and the telephone number
of the sending machine or such business, other entity, or individual. (The telephone number
provided may not be a 900 number or any other number for which charges exceed local or
long-distance transmission charges.)
In order to program this information into your Fax machine refer to “Machine Setup” on page
2-19 and follow the steps provided.
Data Coupler Information
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
Administrative Council for Terminal Attachments (ACTA). On the rear of this equipment is a
label that contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must be provided to the Telephone Company.
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA.
A compliant telephone cord and modular plug is provided with this product. It is designed to
be connected to a compatible modular jack that is also compliant.
WARNING: Ask your local Telephone Company for the modular jack type installed on
your line. Connecting this machine to an unauthorized jack can damage Telephone
Company equipment. You, not Xerox, assume all responsibility and/or liability for any
damage caused by the connection of this machine to an unauthorized jack.
You may safely connect the machine to the following standard modular jack: USOC RJ-11C
using the compliant telephone line cord (with modular plugs) provided with the installation kit.
See installation instructions for details.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 1-15
The Ringer Equivalence Number (or REN) is used to determine the number of devices that
may be connected to a telephone line. Excessive RENs on a telephone line may result in the
devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of devices that may be connected to
a line, as determined by the total RENs, contact the local Telephone Company. For products
approved after July 23, 2001, the REN for this product is part of the product identifier that has
the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal
point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
If this Xerox equipment causes harm to the telephone network, the Telephone Company will
notify you in advance that temporary discontinuance of service may be required. But if
advance notice isn't practical, the Telephone Company will notify the customer as soon as
possible. Also, you will be advised of your right to file a complaint with the FCC if you believe
it is necessary.
The Telephone Company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens the Telephone
Company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
If trouble is experienced with this Xerox equipment, for repair or warranty information, please
contact the appropriate service center; details of which are displayed either on the machine or
contained within the user guide. If the equipment is causing harm to the telephone network,
the Telephone Company may request that you disconnect the equipment until the problem is
resolved.
Repairs to the machine should be made only by a Xerox representative or an authorized Xerox
service agency. This applies at any time during or after the service warranty period. If
unauthorized repair is performed, the remainder of the warranty period is null and void.
This equipment must not be used on party lines. Connection to party line service is subject to
state tariffs. Contact the state public utility commission, public service commission or
corporation commission for information.
If your office has specially wired alarm equipment connected to the telephone line, ensure the
installation of this Xerox equipment does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult your Telephone Company or a
qualified installer.
Page 1-16
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Regulations - Canada
This product meets the applicable Industry Canada technical specifications.
'The Ringer Equivalence Number (REN) is an indication of the maximum number of devices
allowed to be connected to a telephone interface. The termination on an interface may consist
of any combination of devices subject only to the requirement that the sum of the RENs of all
the devices does not exceed five.
The REN value may be found on the label located on the rear of the equipment.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection the electrical ground connections of the power
utility, telephone lines and internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority or electrician, as
appropriate.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 1-17
Environmental Compliance
Energy Star®
XEROX Corporation designed this product to comply with the guidelines of the ENERGY
®
®
STAR program of the Environmental Protection Agency. As an ENERGY STAR Partner,
®
XEROX has determined that this product meets the ENERGY STAR guidelines for energy
efficiency.
Page 1-18
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Unpacking
¾ Remove the shipping tape from
1
the front, back and sides of the
machine.
Tape
LCD
2
z To scan or copy a
document, the
switch must be in
the unlock
¾ Remove the label completely
from the scanner module by
pulling it straight out, away from
the unit.
position. If the
machine is not
being used for a
long period of
time, or being
moved, push the
switch to the lock
Scanner
Module
The scan unlock switch
automatically moves to the unlock
position (
).
position (
).
¾ Pull open the paper tray and
remove the packing material from
the tray.
3
Page 2-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
4
z The appearance
of the power cord
andthetelephone
line cord may
¾ Ensure the following components
are available:
vary according to
Country.
User
AC Power Cord
Documentation
Drum Cartridge
Starter Toner Cartridge
WorkCentre M20 and M20i only:
USB Cable
Telephone Line Cord
Software
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-3
Machine Overview
Models and Options
CopyCentre C20
WorkCentre M20
WorkCentre M20i
Standard
Standard
Standard
Standard
Standard
Standard
Document Feeder
Paper Tray 1 & Bypass
Tray
Standard
Standard
Standard
Option
Standard
-
Standard
Standard
Standard
Standard
Standard
Standard
Option
Digital Copying
Direct Printing
Network Printing
Direct Scanning
Fax
-
-
-
-
-
Option
Option
Option
Option
E-mail
Option
Option
Option
Paper Tray 2
Cabinet and Stand
Foreign Interface
Option
Option
Page 2-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Component Location
Front View:
Document
Guides
Document Input
Document Feeder
Tray
Document
Output Tray
Paper Guides
Control Panel
Bypass Tray
Side Cover
Scanner
Module
Paper
Tray 1
Release lever
Front Cover
Paper Tray 2
NOTE: The components on each model vary, this picture represents the WorkCentre M20i with the
optional Paper Tray 2.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-5
Rear View:
Document Feeder
Document Feeder
Connector
Document Glass
Telephone Connections
Paper Tray
AC Power Cord
Connector
Paper Exit Extension
Power Switch
Parallel Connector
USB Connector
NOTE: The components on each model vary, this picture represents the WorkCentre M20i, standard
configuration.
Page 2-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Control Panel Overview
Navigation keys
Status keys
Display
Clear / Clear All (AC)
Interrupt
Menu/Exit
Copy, Fax and Email keys
1
2
3
5
4
6
7
Alphabet
Keyboard
Start
Stop
Feature
keys (1 - 7)
Enter
Numeric
Keypad
Status Map
Fax
Functions
Paper Supply
ITEM
Alphabet Keyboard
DESCRIPTION
Use to enter alpha and symbol characters for the E-mail and Fax functions.
Use to adjust the contrast level to improve output quality.
1
2
Lighten/Darken
Reduce/Enlarge Use to adjust copy size from 25% to 400% when using the Document
Glass, and 25% to 100% using the Document Feeder.
3
4
5
6
7
2 Sided
Use to scan 2 Sided originals and produce 2 Sided output.
Use to produce collated output.
Collated
Original Type
Color Original
Resolution
Copy
Used to select the type of original being scanned.
Use this option when scanning a color original.
Use to adjust the scan resolution.
Select to activate the Copy mode. The Copy key illuminates when selected.
Fax
Select to activate the Fax mode. The Fax key illuminates when selected.
(WorkCentre M20i only.)
E-mail
Menu/Exit
Enter
Select to activate the E-mail mode. The E-mail key illuminates when
selected.
Use to access the menu functions and also to move up through the menu
levels.
Use to confirm the selection on the display.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-7
Navigation Keys
Paper Supply
Use to scroll through the menu items and the options available for each
menu item.
Use to select a paper type and source. Each press of the Paper Supply key
changes the selection. The Status Map indicates the selected tray.
NOTE: Paper Tray 2 is available as an option.
Status Map
The Status Map identifies which paper tray is selected, when a paper tray is
Document
Feeder Error
empty and when an error occurs.
Bypass
The Status Map has a light for each paper tray. A paper tray can be
selected using the Paper Supply key. Each time the key is pressed, a
different tray is selected and a green light displays to indicate the selected
tray. When two tray lights display together, the Auto Tray Switching feature
is active. This enables the machine to switch to a different tray if the current
tray runs out of paper.
Paper
Jam
Tray 1
Tray 2
If a paper tray is empty, the light will flash and if enabled, an error tone will
sound.
If an error occurs, a red light displays indicating the location of the error,
and a message appears on the display providing further information.
For a detailed description of the error messages, refer to “LCD Error
Messages” on page 11-11.
Display
Job Status
Displays the current status and the menu prompts and selections.
Use to view the current job status, add pages to jobs in memory and to
delete jobs.
Machine Status
Manual Group
Use to access setup menus and customise the machine.
Use to manually enter multiple destinations for a fax job. (WorkCentre M20i
only.)
Manual Dial
Speed Dial
Use to dial a fax number manually. (WorkCentre M20i only.)
Use to dial fax numbers and send faxes by entering a Speed Dial number
which has been set up previously and stored in the machine’s Dial
Directory. (WorkCentre M20i only.)
Pause/Redial
Use to redial the last phone number called or to add a pause when storing a
number in the dial directory. (WorkCentre M20i only.)
Numeric Keypad
Use to enter alphanumeric characters.
Page 2-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Interrupt
Start
Use to interrupt the current copy job to run a more urgent job.
Use to activate a job.
Stop
Use to stop an operation at any time.
Clear/Clear All (AC)
Press once to clear a current entry e.g. an incorrect number or character
entry. Press twice to clear all programmed settings, the display requests
confirmation.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-9
Installing Drum and Toner Cartridges
¾ Pull the release latch to open the
1
side cover.
CAUTION: Ensure the side cover
is always open before opening
the front cover.
¾ Open the front cover.
2
¾ If the cartridge locking lever is in
3
the lower position, turn the lever
upward until it locks into place.
Page 2-10
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
¾ Remove the drum cartridge from
its bag and slide it into the
machine firmly until it locks into
place.
4
5
CAUTION: Do not expose the
green drum to light for an
extended period. Never expose
the drum to direct sunlight or
touch the drum surface. Damage
or poor image quality may result.
z Xerox
¾ Remove the starter toner
has included a
Starter Toner
Cartridge.
cartridge from its bag.
¾ Gently shake the cartridge to
Purchased
loosen the toner.
replacement
toner cartridges
will yield
approximately
two times the
number of copies.
Shaking the cartridge will ensure
maximum copies per cartridge.
¾ Slide the toner cartridge into the
machine, aligning the cartridge to
the left of the slot, until it locks
into place.
6
7
z Whenthe drumor
toner cartridge
need to be
¾ Turn the toner locking lever
downwards until it locks in place.
replaced a
message
displays.
¾ Close the front cover and the side
cover.
The product returns to Standby
mode.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-11
Making Connections
Document Feeder
1
¾ Connect the Document Feeder
cord to the port shown and fasten
the side screws.
Telephone Line (WorkCentre M20i only)
2
z You should use
the telephone line
cord which is
¾ Connect the supplied telephone
line to the LINE jack and the other
end to the wall jack.
suppliedwithyour
machine. If you
are replacing it
with another
If you want to use your machine
for receiving both faxes and voice
calls, you will need to connect a
telephone and/or answering
machine.
vendor’s, it
should be AWG
#26 or larger tele-
communication
line cord.
¾ If required, plug the cord of your
extension phone into the EXT
jack.
Page 2-12
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
USB or Parallel Port Cable
(WorkCentre M20 and M20i only)
3
CAUTION: Shut down the
computer before connecting the
cable.
¾ Connect the USB Cable which
came with your machine.
OR
¾ If you want to use a parallel print
cable, only use an IEEE-1284
compliant cable and connect it to
the parallel connector on your
machine.
Only connect one of the above cables. If you are using a USB cable, you must be running
)
Windows 98, Me, 2000 or XP. When using the USB connection, your machine provides two USB
modes; Fast and Slow. Fast is the default mode. Some PC User’s may experience poor
functionality in the default mode. If this occurs, select the Slow mode. For information about
changing the USB mode, refer to “Machine Setup” on page 2-19.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-13
Powering On the Machine
¾ Connect the AC Power Cord to
1
the machine and a power outlet.
The power cord must be plugged
into a grounded power socket.
¾ Press the ON/OFF switch to the
2
ON ( I ) position.
The machine displays ’Warming
Up Please Wait...’.
Page 2-14
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Loading Paper
1
z An additional
¾ Pull open the Paper Tray.
Paper Tray is
available as an
option. The
instructions for
loading both
paper trays are
the same.
¾ Push down on the pressure plate
2
3
until it locks into position.
¾ Adjust the rear paper guide to the
required paper length.
It is preset to A4 or Letter size
depending on country.
¾ To load another size, lift the rear
guide out of the current position
and into the required position.
Rear
Guide
L
The Paper Trays can hold a
maximum of 550 sheets of 80 g/m2
(20 lb) plain paper. You can use
A4, Letter or Legal size paper only.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-15
4
z If you experience
problems with
¾ Fan the paper and insert it into
the tray.
paper feed, turn
the paper around
and if the problem
continues, use
If loading Letterhead, ensure the
design is face-up and the top
edge of the sheet is placed at the
right side.
the Bypass Tray.
¾ Ensure that the paper is
5
positioned under the snubbers.
Corner
snubbers
¾ Do not fill above the Maximum Fill
Line.
Max Fill
Line
Page 2-16
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
6
z When printing
¾ Position the side guide by
squeezing the lever and sliding it
toward the stack of paper, until it
gently touches the side of the
stack.
from your PC,
ensure you select
the Paper Source
and the correct
paper size from
your software
application.
Do not allow the guide to press
against the edge of the paper
tightly.
¾ Close the Paper Tray.
)
For more detailed information about Paper Supply, refer to the Chapter “Paper and Other Media”
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-17
Help List
The Help List contains information about the features and settings available on your machine.
It is helpful to print the list to use as a reference tool when performing Machine Setup tasks.
Use the following instructions to print the Help List.
¾ Press the [Menu/Exit] key.
1
Menu/Exit
Enter
¾ Using the Navigation Keys select
2
3
the [Help List] and press [Enter].
E-Mail Feature
Æ Help List
Help List Printing... displays.
The Help List is printed.
¾ Press [Menu/Exit] to exit each menu level and return to standby mode.
Page 2-18
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Machine Setup
Use the following instructions to customize your machine to meet your individual
requirements.
¾ Press the [Machine Status] key.
1
Enter Machine
Status
¾ Using the Navigation Keys select
[Machine Setup] and press
[Enter].
2
3
Æ Machine Setup
Fax Setup
¾ Using the Navigation Keys select
the required setup option and
press [Enter].
Machine Setup
[Tray 1 Size]
¾ Using the “Machine Setup
Options:” starting on page 2-20
customize the settings to meet
your requirements.
¾ Press [Enter] to save your
selections.
¾ Press [Menu/Exit] to exit each menu level and return to standby mode.
4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-19
Machine Setup Options:
OPTION
Tray 1 Size
SETTINGS
DESCRIPTION
LTR / A4 / LGL / Folio Use to set the default paper size
for Tray 1. Paper Size options are
Letter, A4, Legal (216 x 356 mm /
8.5 x 14 inch) or Folio.
Tray 2 Size
LTR / A4 / LGL / Folio Use to set the default paper size
for Tray 2. Paper Size options are
Letter, A4, Legal (216 x 356 mm /
8.5 x 14 inch) or Folio.
Bypass Size
LTR / A4 / LGL / Folio / Use to set the default paper size
A5 / Statement
for the Bypass tray. Paper Size
options are Letter, A4, Legal (216 x
356 mm / 8.5 x 14 inch), Folio, A5
or Statement.
L
If feeding media smaller than A4/
Letter through the bypass tray,
the setting can remain set at A4,
Letter or Legal size.
When copying onto a paper size
smaller than A4/Letter, the
printed image may be offset and
not reproduce correctly, even
when Auto Fit is selected.
Power Save
On
Off
Use to enable the Power Save
feature. If On is selected, set the
period of time the machine waits
before Power Save is activated.
Choose between 5, 10, 15, 30 or
45 minutes.
Time Out
15 / 30 / 60 / 180
Seconds
Sets the number of seconds the
machine remains idle before
switching to Power Save mode.
The period set here starts after the
last print job.
OFF
Page 2-20
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
OPTION
SETTINGS
ON
DESCRIPTION
Stamp RX Name
Set to ON to enable the page
number and date and time of
reception to be printed on each
page of each received
OFF
transmission.
Alarm Sound
ON
Set to ON to enable an alarm
sound when an error occurs or a
fax communication ends.
OFF
Key Sound
ON
Set to ON to enable a key sound
when any key is pressed.
OFF
ON
Speaker Control
The speaker can be set to ON,
OFF or COM. With this option set
to COM, the speaker is on until the
remote machine answers.
OFF
COM
Language
English, French,
The LCD displays in the language
Spanish, Portuguese, selected.
German, Italian, Dutch,
Danish, Swedish,
Finnish, Norwegian,
Swedish, Russian
Localization
Select Country
Inch
MM
FAST is the default mode. Some
PC users may experience poor
USB implementation in the default
mode. If this occurs, select the
SLOW mode in order to achieve
successful results.
-
Setting the COUNTRY option sets
the correct fax communication
settings for the PSTN system
pertaining to each country.
NOTE: The Country option is not
applicable to North America and
Canada.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-21
OPTION
USB Mode
SETTINGS
Fast
DESCRIPTION
Use to set the USB speed. Fast is
the default mode. Some PC users
may experience poor USB
Slow
implementation in the default
mode. If this occurs, select the
SLOW mode in order to achieve
successful results.
Device Name
Date & Time
Fax
ID
Use to enter the fax number and
name of the machine.
Enter the current date and time
using the numeric keypad. Use
Clock Mode to set whether the
machine uses a 12 or 24 hour
clock.
Clock Mode
12 hour
24 hour
The machine can be configured to
display time using either a 12-hour
or 24-hour format.
Toner Save
ON
OFF
Use to set the machine to use less
toner and print lower quality output.
Discard Size
[00 - 30]
If the Fax Setup option Auto
Reduction is turned OFF or fails,
and the received document is as
long or longer than the paper
selected, the machine will discard
any excess image at the bottom of
the page.
z When receiving a
document as long as or
longer than the paper in
the machine, the fax
machine can be set to
discard any excess at the
bottom of the page.
If the received page is outside the
discard margin set, it will print on
two sheets of paper at the actual
size.
Margins can be set between 0 -
30mm (1.2")
Page 2-22
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Installing Software
There are four drivers provided:
-
-
-
-
PCL5
PostScript
Twain
ControlCentre
The installation procedure is the same for all of them. You can install all of the drivers at the
same time or as many as you require.
These instructions are for installing direct printing and scanning via the parallel or USB. For
)
Xerox WorkCentre M20i network connections, it is recommended that you contact your System
Administrator or refer to the System Administration Guide.
The Xerox WorkCentre M20 and M20i can be connected directly to the USB or Parallel Port
of a host Workstation. A document file can be sent or received from the host Workstation via
the appropriate port to the Xerox WorkCentre M20 or M20i.
Prior to installing the drivers, ensure the USB or Parallel Port connection has been made
between the Xerox WorkCentre M20 or M20i and the Workstation.
For USB or Parallel Port connection instructions, refer to “Making Connections” starting on page
2-12.
There are three stages required to installing the machine on a port on a local workstation:
¾ Install the driver.
This requires the appropriate printer driver to be installed on the workstation.
¾ Workstation Setup
This requires the workstation to be configured to print to the WorkCentre M20i.
¾ Test Print or Scan
A print job should be submitted to ensure the WorkCentre M20i has been installed and
configured correctly.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-23
Driver Installation
Before direct printing, direct scanning or using ControlCentre through the Parallel Port or the
USB port, you will need to install a driver.
The procedure will install the driver and configure it for the local port.
To install the driver on the workstation.
¾ Insert the Driver CD into the CD drive.
1
Within a few seconds, the CD should start automatically and present you with the opening
screen. If this does not happen, go to the Start menu, select [Run] and browse to the CD
drive. Select [Setup] and click [OK]. Click [OK] to start the installation procedure.
¾ Select the language for the installation and select [Continue].
2
3
The driver screen is displayed.
¾ Check the boxes for the drivers required, PostScript, PCL, PC Scan and ControlCentre.
¾ Select [Continue].
You can choose to install as many drivers as you require by checking the appropriate boxes.
)
Page 2-24
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
The selection will be confirmed.
¾ Select [Continue] to confirm your choice and install the driver.
4
The installation will continue by transferring a number of files.
If you chose to install multiple drivers, the installation process will be repeated for each driver.
)
¾ Select [Finish] to complete the installation.
5
6
¾ Switch the printer Off and then On.
For instructions for powering the machine on and off, refer to “Powering On the Machine”
starting on page 2-14.
¾ Reboot the Workstation.
7
Windows will automatically detect new hardware and install the appropriate driver.
installation.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-25
Workstation Setup
You will need to configure the printer drivers.
¾ At the Workstation, select [Printers and Faxes] from the Control Panel option.
1
The location of this window will vary according to the operating system: from the Start>Settings
menu or directly from the Start menu.
)
The Printers and Faxes window will be displayed.
This window will have a different appearance according to the operating system of the
)
workstation. The window displayed is for a Windows XP operating system.
¾ Click on the Printer and select [Properties] from the File menu or the right mouse menu.
2
A properties window will be displayed.
Page 2-26
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
This window will have a different appearance according to the operating system of the
workstation and the type of driver installed. The window displayed is for a Windows XP operating
system.
)
¾ Click on the [Ports] tab.
3
The Ports tab will be displayed.
¾ Check the box appropriate to the connection.
4
5
For a parallel connection, check LPT1, LPT2 or LPT3 depending on the configuration of
the workstation. This is usually LPT1.
For a USB connection, check the USB box.
¾ Click [OK].
installation.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 2-27
Test Print or Scan
To ensure the Xerox WorkCentre M20 or M20i has been installed correctly a test print or scan
should be submitted from the Workstation.
Test Print
Perform the following steps:
¾ Open a document on the Workstation.
1
2
3
¾ Select the Xerox WC M20 Series as the printer to which the document will be sent.
¾ Print the selected document on the device and verify that it prints correctly.
The installation process is now complete.
Test Scan
¾ Open the Twain compliant application being used to scan documents.
1
2
verify that it scans correctly.
The installation process is now complete.
Page 2-28
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Copying Procedure
Select Copy Mode
1
¾ Ensure Ready to Copy displays.
Ready To Copy
100%
001
Current Reduction /
Number of Copies
Enlarge Setting
Copy Key
¾ If necessary, press the [Copy]
key to change to Copy mode.
The Copy key remains
illuminated when selected.
Select the Paper Supply
2
z For instructions
on loading media,
¾ To select a paper tray, press the
[Paper Supply] key until the
required tray is lit on the Status
Map.
For full media
specifications
Tray 1 and the Bypass Tray are
available as standard, Tray 2 is
optional.
If two tray lights display together,
the Auto Tray Switching feature is
active. When one tray runs out of
paper, the machine will switch to
the other selected tray.
Status Map
Paper Supply
Page 3-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
When copying onto a paper size smaller than A4/Letter, the printed image may be offset and not
reproduce correctly, even when Auto Fit is selected.
)
¾ If the Bypass Tray is selected the
Paper Type option displays. Use
the Navigation Keys to select the
Paper Type being loaded and
press [Enter].
If using the Bypass, remember to
load the required stock.
Navigation Keys
Enter
Load the Originals
3
Document Feeder:
¾ Remove all staples and paper
clips prior to loading.
¾ Adjust the sliding document
Document
Guides
guides to the size required.
¾ Insert the originals neatly into the
Document Feeder, face up.
The first page should be on top
with the headings towards the
back or left of the machine.
¾ Align the stack with the left and
rear edges of the tray. Adjust the
guides to just touch the edges of
the originals.
L
Up to 50 sheets of 80 g/m2 (20lb bond) paper can be loaded. Weight ranges from 45 - 105 g/m2
(12.5 - 28lb). Sizes range from B5 to Legal (7” x 10” to 8.5” x 14” ). Refer to “Scanner and Copier
Specifications” on page 12-5 for full Document Feeder specifications.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 3-3
Document Glass:
z When using the
Document Glass,
ensure there are
no documents in
the Document
Feeder.
¾ Raise the Document Feeder and
position the original face down on
the Document Glass.
Align with the registration arrow in
the rear left corner.
Leaving the
Document
¾ Lower the Document Feeder.
Feeder open
while scanning
will affect the
image quality and
toner
consumption.
Select the Copy Features
4
z Only those
features relevant
to the machine
configuration will
be available.
¾ Press the Copy feature key
Lighten/Darken
Original Type
required on the Control Panel.
Basic features available for Copy
jobs are Lighten/Darken, Reduce/
Enlarge, 2 Sided, Collated,
Reduce/
Original Type and Color Original.
Enlarge
2 Sided
Collated
For information about all the
)
available Copy features, refer to
Color Original
¾ Using the Navigation Keys, select
the setting required for the
feature and press [Enter].
Page 3-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Enter the Quantity
5
z The maximum
¾ Use the Numeric Keypad to enter
copy quantity is
999.
the number of copies required.
¾ If necessary, press [Clear/Clear
All] to clear the current quantity
and enter a new quantity.
Numeric Keypad
Clear/Clear All
6
z You can cancel a
copy job while it is
copying by
pressing the
[Stop] key twice.
Press Start
¾ Press [Start] to begin the copy
job.
¾ If Collated is On, when the
document is fed from the
Document Glass, the display
shows [Scan Another?].
Navigation Keys
Start
¾ To scan another original, load the
next original and using the
Navigation Keys select [Yes] and
press [Enter].
Continue the procedure until all
the originals have been scanned.
¾ Select [No] when all the originals
have been scanned, and press
[Enter].
Printing commences and copies
are delivered to the Output Tray.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 3-5
Basic Copy Features
There are seven basic Copy features available. These features can be selected using the
feature keys located on the Control Panel.
Lighten/Darken
Original Type
Reduce/
Enlarge
2 Sided
Collated
Color Original
Feature Description
FEATURE
OPTIONS
INSTRUCTIONS
Lighten/Darken 5 Contrast Settings
¾ Press [Copy].
¾ Press [Lighten/Darken].
z Use toadjustthe
contrast for a
document
¾ Using the Navigation Keys select a contrast
containing faint
or dark images.
setting.
Each time the key is pressed the selection block
on the display moves to the left or right. As the
selection block moves to the right the contrast
becomes darker.
¾ Press [Enter] to save the selection.
Reduce/Enlarge 25 - 400% Reduce/Enlarge from 25 - ¾ Press [Copy].
400% using the
Document Glass, and
from 25 - 100% using the ¾ Enter the percentage required using the Numeric
Document Feeder.
¾ Press [Reduce/Enlarge].
z Use to reduce or
enlarge an
image from 25%
to 400%,
depending on
the input area
used.
Keypad. The selected number appears on the
display.
¾ Press [Enter] to save the selection.
Page 3-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Clone
Use to print multiple
images on a single sheet
of paper. The number of
images produced is
determined automatically
based on the original
image size.
¾ Press [Copy].
¾ Press [Reduce/Enlarge].
¾ Using the Navigation Keys, select [Clone] and
press [Enter].
Clone appears on the display.
z Only available using the
Document Glass, ensure
the Document Feeder is
empty.
Auto Fit Use to reduce or enlarge ¾ Press [Copy].
the image to fit the paper
size automatically.
¾ Press [Reduce/Enlarge].
¾ Using the Navigation Keys, select [Auto Fit] and
z Only available using the
Document Glass, ensure
the Document Feeder is
empty.
press [Enter].
Auto Fit appears on the display.
2 Sided
1-1 Sided Use when originals are
printed on 1 side and 1-
¾ Press [Copy].
¾ Press [2 Sided].
z Use to produce
1 or 2 sided copy
output from 1 or
2 sided originals.
sided copies are required.
¾ Use the Navigation Keys to select the option
1-2 Sided Use when originals are
required and press [Enter] to save the selection.
Long
printed on 1 side only and
2 Sided copies, with the
conventional "head to
¾ If necessary, use the [Scan Side 2] option to scan
side 2. Position side 2 on the Document Glass
and select [Yes] then [Enter] to scan side 2.
head" layout are required.
Continue the procedure until all the originals have
been scanned.
1-2 Sided Use when originals are
Short
printed on 1 side only and
2 Sided copies, with the
"head to toe" layout are
required.
¾ Select [No] when all the originals have been
scanned, and press [Enter].
2-1 Sided Use when originals are
Long
printed on both sides, with
the conventional "head to
head" layout, and 1 sided
copies required.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 3-7
2-1 Sided Use when originals are
¾
Short
printed on both sides in
the "head to toe" layout,
and 1 sided copies are
required.
2-2 Sided Use for originals that are
printed on 2 sides and 2
Sided copies are
required.
Collated
On
Use to produce collated
output e.g. 2 copies of a 3
page job will print one
complete document,
¾ Press [Copy].
¾ Press [Collated].
z Use to produce
collated copy
sets.
¾ Use the Navigation Keys to select [On] and press
followed by the second
complete document.
[Enter].
Original Type
Text
Use for documents
¾ Press [Copy].
containing mostly text.
¾ Press [Original Type].
z Use to select the
type of
document being
scanned.
Mixed
Use for documents with
mixed text and graphics.
¾ Use the Navigation Keys to select the option
required and press [Enter].
Photo
On
Use for photographs.
Color Original
Use when scanning color ¾ Press [Copy].
originals.
¾ Press [Color Original].
z Use when
scanning a color
original.
¾ Use the Navigation Keys to select [On] and press
[Enter].
Page 3-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Paper Supply
Status
Map
The Status Map identifies ¾ Press [Copy].
which paper tray is
selected, when a paper
tray is empty and when an
¾ To select a paper tray, press the [Paper Supply]
z Use to select the
paper source.
key until the required tray is lit on the Status Map.
error occurs.
Document
Feeder Error
The Status Map identifies which paper tray is
selected, when a paper tray is empty and when an
error occurs. The Status Map has a light for each
paper tray.
Bypass
Paper
Jam
Each time the [Paper Supply] key is pressed, a
different tray is selected and a green light displays
to indicate the selected tray. When two tray lights
display together, the Auto Tray Switching feature
is active. This enables the machine to switch to a
different tray if the current tray runs out of paper.
Tray 1
Tray 2
If a paper tray is empty, the light will flash and if
enabled, an error tone will sound.
Bypass Use to notify the machine ¾ If the Bypass Tray is selected the Paper Type
the type of paper loaded
in the Bypass Tray.
option displays. Use the Navigation Keys to
select the Paper Type being loaded and press
[Enter].
If using the Bypass, remember to load the
required stock.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 3-9
Special Copy Features
The special Copy features available can be accessed by pressing the Menu/Exit key and then
selecting Copy Features on the display.
Menu/Exit
Enter
Navigation Keys
Feature Description
FEATURE
OPTIONS
TO SELECT
ID Card Copy
-
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [Copy Features]
z Useto copy both
sides of an ID
document e.g. a
drivers license,
onto one side of
paper.
and press [Enter].
¾ Use the Navigation Keys to select [ID Card Copy]
and press [Enter].
¾ [Press Start S.1] displays. Load Side 1 of the
original on the Document Glass and press [Start].
¾ Repeat for Side 2 when [Press Start S.2] displays.
The machine prints both sides of the ID document
on one side of paper.
Page 3-10
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Edge Erase
Off
Use to de-activate the
feature.
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [Copy Features]
z Use to ’clean up’
the edges of an
original e.g. if it
is frayed or has
hole punch or
and press [Enter].
Small Orig Use to erase 6 mm (0.25")
Edges
from the edge of the
document.
¾ Use the Navigation Keys to select [Edge Erase]
and press [Enter].
staple marks.
Binder Use to erase 24 mm (1.0")
¾ Select the required Edge Erase option and press
Holes
from the left edge of the
document.
[Enter] to save the selection.
Book
Use to erase 6 mm (0.25")
Center & from the left and right
Edges edge of the document.
Border Use to create a border
Surround around all edges of the
document.
Margin Shift
Off
Use to de-activate the
feature.
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [Copy Features]
z Use to create a
binding edge for
the document.
and press [Enter].
Auto
Use to center the image
Center on the paper.
¾ Use the Navigation Keys to select [Margin Shift]
and press [Enter].
Left
Use to enter a shift
Margin amount for the left margin.
¾ Select the required Margin Shift option and press
[Enter].
Right
Use to enter a shift
Margin amount for the right
¾ If required, enter a shift amount using the Numeric
margin.
Keypad and press [Enter].
Top
Use to enter a shift
Margin amount for the top
margin.
Bottom Use to enter a shift
Margin amount for the bottom
margin.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 3-11
Book Copy
Off
Use to de-activate the
feature.
¾ Use the Document Glass when copying bound
documents.
z Use when
copying bound
documents. If
the document is
too thick, lift the
cover until its
hinges are
caught by the
stopperandthen
close the cover.
¾ Press [Menu/Exit].
Left Page Use to scan and copy the
left page of a bound
¾ Using the Navigation Keys select [Copy Features]
document.
and press [Enter].
Right
Page
Use to scan and copy the
right page of a bound
document.
¾ Use the Navigation Keys to select [Book Copy]
and press [Enter].
¾ Select the required Book Copy option and press
Both
Pages
Use to scan and copy
both pages of a bound
document.
[Enter].
Auto Suppress
On
Off
Use to activate the ’Auto ¾ Press [Menu/Exit].
Suppress’ feature.
¾ Using the Navigation Keys select [Copy Features]
z Use when
copyingoriginals
which require
the background
removing.
and press [Enter].
Use to de-activate the
feature.
¾ Use the Navigation Keys to select [Auto
Suppress] and press [Enter].
¾ Select [On] and press [Enter].
Covers
Off
Use to de-activate the
feature.
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [Copy Features]
z Use to
automatically
add covers to
your copied set
using stock
taken from
and press [Enter].
Front
Use to add a blank or
printed front cover to the
copies.
¾ Use the Navigation Keys to select [Covers] and
press [Enter].
Back
Use to add a blank or
printed back cover to the
copies.
another tray.
¾ Select the required Covers option and press
[Enter].
¾ Select the Paper Tray containing the covers stock
Front & Use to add a blank or
and press [Enter].
Back
printed front and back
cover to the copies.
¾ Select [Blank] or [Printed] depending on your
requirement, and press [Enter].
Page 3-12
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Transparencies
Off
Use to de-activate the
feature.
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [Copy Features]
z Use to create a
single set of
transparencies
with blank or
printed
and press [Enter].
Bypass Use to create a single set
of transparencies with a
blank or printed divider
between each
¾ Use the Navigation Keys to select
[Transparencies] and press [Enter].
separators.
¾ Use the Navigation Keys to select [Bypass] and
transparency.
press [Enter].
¾ Use the Navigation Keys to select [Off], [Printed]
or [Blank] for the separators and press [Enter].
¾ Select a Paper Tray for the separators and press
[Enter].
Create Booklet
On
Off
Use to activate the
’Create Booklet’ feature.
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [Copy Features]
z Use to copy a
document as a 2
Sided job and
arrange the
pages to
and press [Enter].
Use to de-activate the
feature.
¾ Use the Navigation Keys to select [Create
Booklet] and press [Enter].
produce a
booklet when
folded.
¾ Select [On] and press [Enter].
N Up
Off
Use to de-activate the
feature.
¾ Press [Menu/Exit].
¾ Using the Navigation Keys to select [Copy
z Use to print 2 or
4 original
images reduced
on to one page.
Features] and press [Enter].
2 Up
Use to print the images
from 2 originals on to one
page.
¾ Use the Navigation Keys to select [N Up] and
press [Enter].
4 Up
Use to print the images
from 4 originals on to one
page.
¾ Select the required N Up option and press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 3-13
Using Interrupt
The Interrupt button is used to temporarily pause the job which is currently being copied in
order to run a more urgent job. This feature is useful if the machine is printing a large job as it
still provides access to Copy mode for running small, quick jobs.
Select Copy Mode
1
2
Copy Key
¾ Interrupt is only available in Copy
mode. Press the [Copy] key to
activate Copy mode.
Select Interrupt
¾ To interrupt the current Copy job,
press the [Interrupt] key.
¾ The machine activates the
Interrupt feature and the Interrupt
key remains illuminated.
The job pauses after the current
sheet has been printed or the
current original has been
scanned.
Interrupt
If the current job cannot be
)
interrupted, a message displays.
Page 3-14
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
.
Load the Originals
3
4
¾ Remove all staples and paper
clips prior to loading.
¾ Load the originals for the Interrupt
job into the Document Feeder or
load a single original on the
Document Glass.
For full instructions on loading
)
originals refer to “Load the
Select the Interrupt Job Features
z Only those
features relevant
to the machine
configuration will
be available.
¾ Basic features available for Copy
Lighten/Darken
Original Type
jobs are Lighten/Darken, Reduce/
Enlarge, 2 Sided, Collated,
Original Type and Color Original.
Reduce/
Enlarge
For information about all the
)
available Copy features, refer to
2 Sided
Collated
Color Original
¾ Press the feature key required
and using the Navigation Keys,
select the setting required for the
feature. Press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 3-15
Enter the Quantity
5
z The maximum
¾ Use the Numeric Keypad to enter
copy quantity is
999.
the number of copies required.
Numeric Keypad
Press Start
6
7
¾ Press [Start] to begin the Interrupt
job.
¾ If using the Document Glass and
[Scan Another?] displays, select
[Yes] to scan another original, or
[No] if all originals have been
scanned; press [Enter].
Navigation Keys
Start
The Interrupt job is printed.
If another urgent job is required
repeat the procedure.
Resume Current Job
¾ To resume the interrupted job,
Interrupt
press the [Interrupt] button.
The Interrupt feature is
deactivated.
¾ If required, reorder and reload the
originals as instructed and press
[Start].
The interrupted job resumes.
Start
Page 3-16
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Compatible Features
The following table indicates which features are compatible with other features. It also shows
which input area can be used for a feature e.g. the Document Feeder or Document Glass.
Document
Feeder or Glass
ID Copy Book Create N Up
Copy Booklet
Edge Erase
Margin
Shift Suppress
Auto
Covers
Trans-
parencies
COPY
FEATURE
ID Copy
Glass
Glass
Book Copy
Create Booklet
X
Document Feeder
X
X
X
X
2 Up
Glass / Document
Feeder
N Up
O
4 Up
Document Feeder
Glass
X
X
X
X
X
X
Small Orig
Edges
Edge
Erase
X
O
X
O
X
X
X
X
X
O
X
Binder Holes Glass / Document
X
X
X
X
X
X
X
X
X
X
X
O
X
X
X
O
X
X
X
X
X
O
X
Feeder
Book Center
& Edges
Glass
Border
Surround
Glass / Document
Feeder
Auto Center
Glass
Margin
Shift
X
O
Small Orig Only
Left
Glass / Document
Feeder
O
O
O
O
O
O
O
Not Book Center & Edges
Right
Glass / Document
Feeder
O
Not Book Center & Edges
Top
Glass / Document
Feeder
O
Not Book Center & Edges
Bottom
Glass / Document
Feeder
O
Not Book Center & Edges
Glass / Document
Feeder
Auto Suppress
Covers
O
O
Glass / Document
Feeder
O
O
O
O
O
Not Book Center & Edges Not Auto
Center
Glass / Document
Feeder
Transparencies
X
X
O
O
X
X
X
X
O
O
X
Not Auto
Center
%
Glass / Document
Feeder
R/E
O
X
O
O
Binder Holes & Border
Surround Only
AutoFit
Clone
Glass
Glass
X
X
X
X
O
X
X
X
X
X
X
X
O
X
X
O
O
O
O
X
X
O
O
O
X
Small Orig Only
O
Small Orig Only
Glass / Document
Feeder
Collate
O
Not Book Center & Edges
Key:
O
X
=
=
Compatible
Incompatible
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 3-17
Page 3-18
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Loading Paper
Preparing Paper for Loading
Before loading paper into the Paper Trays, fan the edges. This procedure separates any
sheets of paper that are stuck together and reduces the possibility of paper jams.
To avoid unnecessary paper jams and misfeeds do not remove paper from its packaging until
)
required.
Using the Paper Trays
Loading the Paper Trays
Using the instructions provided, load paper into the machine. Up to two Paper Trays are
available, depending on your machine configuration. The Paper Trays can hold a maximum
2
of 550 sheets of 80 g/m (20 lb) plain paper.
¾ To load paper, pull open the
1
2
Paper Tray.
¾ Push down on the pressure plate
until it locks into position.
Page 4-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
¾ Adjust the rear paper guide to the
3
4
required paper length.
It is preset to A4 or Letter size
depending on country.
¾ To load another size, lift the rear
guide out of the current position
and into the required position.
Rear
Guide
L
The Paper Trays can hold a
maximum of 550 sheets of 80 g/m2
(20 lb) plain paper. You can use
A4, Letter or Legal size paper only.
z If you experience
problems with
¾ Fan the paper and insert it into
the tray.
paper feed, turn
the paper around
and if the problem
continues, use
If loading Letterhead, ensure the
design is face-up and the top
edge of the sheet is placed at the
right side.
the Bypass Tray.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 4-3
¾ Ensure that the paper is
5
positioned under the snubbers.
Corner
snubbers
¾ Do not fill above the Maximum Fill
Line.
Max Fill
Line
6
z When printing
¾ Position the side guide by
squeezing the lever and sliding it
toward the stack of paper, until it
gently touches the side of the
stack.
from your PC,
ensure you select
the Paper Source
and the correct
paper size from
your software
application.
Do not allow the guide to press
against the edge of the paper
tightly.
¾ Close the Paper Tray.
Tray.
)
Page 4-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
¾ To select a paper tray, press the
[Paper Supply] key until the
required tray is lit on the Status
Map.
7
Tray 1 and the Bypass Tray are
available as standard, Tray 2 is
optional.
If two tray lights display together,
the Auto Tray Switching feature is
active. When one tray runs out of
paper, the machine will switch to
the other selected tray.
Status Map
Enter
Paper Supply
Using the Bypass Tray
The Bypass Tray is located on the right side of your machine. It can be closed when not in
use, making the product more compact. Use the Bypass Tray to print transparencies, labels,
envelopes or postcards in addition to making quick runs of paper types or sizes that are not
currently loaded in the paper tray.
Acceptable print media is plain paper with sizes ranging from 98 x 148 mm (3.86 x 5.83 inch),
2
2
to Legal size (216 x 356 mm / 8.5 x 14 inch) and weighing between 60 g/m and 160 g/m (16
lb and 43 lb).
The following table summarizes the print media allowed and the maximum stacking height for
each paper type.
PAPER TYPE
MAXIMUM STACKING HEIGHT
100 sheets or 9 mm (0.35 inch)
Plain/Bond/Colored and Pre-
printed Paper
Envelope
Transparency
Label
10 envelopes or 9 mm (035 inch)
30 sheets or 9 mm (0.35 inch)
10 sheets or 9 mm (0.35 inch)
10 sheets or 9 mm (0.35 inch)
Cardstock
L
The height is measured with the stack of sheets laid on a flat surface.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 4-5
Loading the Bypass Tray
1
z Remove any curl
on postcards,
envelopes, and
labels before
¾ Lower the Bypass Tray, located
on the right side of the product.
¾ Unfold the Paper Support
loading them into
the Bypass Tray.
extension.
Paper
Support
Bypass Tray
¾ Prepare a stack of paper or
envelopes for loading by flexing
or fanning them back and forth.
Straighten the edges on a level
surface.
2
3
z Hold
¾ Load the print material with the
print side facing down and
transparenciesby
the edges and
avoid touching
the print side.
against the right edge of the tray.
¾ Adjust the paper guide to the
width of the stack of print
material.
34
Ensure you have not loaded too
much print media. The stack
should be under the Max. Fill
Line.
Page 4-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
¾ To select the Bypass Tray, press
the [Paper Supply] key until the
Bypass tray is lit on the Status
Map.
5
¾ When the Bypass Tray is
selected the Paper Type option
displays. Use the Navigation
Keys to select the Paper Type
being loaded and press [Enter].
Status Map
Enter
Paper Supply
Tray.
)
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 4-7
Setting the Paper Size
After loading paper in the Paper Trays, you will need to set the default Paper Size. Use the
following instructions to set the default Paper Size for each tray.
¾ Press the [Machine Status] key on the Control Panel.
1
2
¾ Select [Machine Setup] using the Navigation Keys and press [Enter].
The display shows [Tray 1 Size] on the bottom line.
¾ Press [Enter].
¾ Use the Navigation Keys to select the Paper Size required and press [Enter] to save the
13
4
selection.
¾ Repeat the procedure for [Tray 2 Size] if available, and [Bypass Size].
¾ Press [Menu/Exit] to exit each menu level and return to Standby mode.
Page 4-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Media Specifications
Media Sizes and Types
The table below identifies the media sizes which can be used in the Paper Tray and Bypass
Tray, and the capacities which can be loaded.
a
MEDIA SIZE
INPUT SOURCE CAPACITY
Paper Tray Bypass Tray
Plain paper
Letter (8.5 x 11 inch)
550
100
YES
YES
YES
NO
YES
YES
YES
YES
YES
YES
YES
Folio (8.5 x 13 inch)
Legal (8.5 x 14 inch)
Executive (7.25 x 10.5 inch)
A4 (210 x 297 mm)
B5 (182 x 257 mm)
A5 (148 x 210 mm)
550
550
0
100
100
100
100
100
100
550
0
YES
NO
0
NO
Envelopes
No. 10 (8.5 x 14 inch)
C5 (6.38 x 9.37 inch)
DL (110 x 220 mm)
0
0
0
0
0
10
10
10
10
10
NO
NO
NO
NO
NO
YES
YES
YES
YES
YES
Monarch (3.87 x 7.5 inch)
B5 (176 x 250 mm)
b
Labels
0
0
10
10
NO
NO
YES
YES
Letter (8.5 x 11 inch)
A4 (210 x 297 mm)
b
Transparency films
Letter (8.5 x 11 inch)
0
0
30
30
NO
NO
YES
YES
A4 (210 x 297 mm)
b
Card stocks
0
0
0
10
10
10
NO
NO
NO
YES
YES
YES
A6 (105 x 148.5)
Post Card (4 x 6 inch)
Hagaki (5.83 x 8.27 inch)
L
a.
b.
Depending on paper thickness, maximum capacity may be reduced.
Feed one sheet at a time through the Bypass Tray if jams occur.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 4-9
Media Guidelines
When selecting or loading paper, envelopes, or other special media please adhere to these
guidelines:
¾ Attempting to print on damp, curled, wrinkled, or torn paper can cause paper jams and
poor print quality.
¾ Use only high quality copier grade paper. Avoid paper with embossed lettering,
perforations, or texture that is too smooth or too rough.
¾ Store paper in its ream wrapper until ready to use. Place cartons on pallets or shelves, not
on the floor. Do not place heavy objects on top of the paper, whether it is packaged or
unpackaged. Keep it away from moisture, or other conditions that can cause it to wrinkle or
curl.
¾ During storage, moisture-proof wrap (any plastic container or bag) should be used to
prevent dust and moisture from contaminating your paper.
¾ Always use paper and other media that conform with the specifications detailed in
¾ Use only well-constructed envelopes with sharp, well creased folds:
-
-
DO NOT use envelopes with clasps and snaps.
DO NOT use envelopes with windows, coated lining, self-adhesive seals, or other
synthetic materials.
-
DO NOT use damaged or poorly made envelopes.
¾ It is recommended that you feed special paper types one sheet at a time.
¾ Only use the special media recommended for use in laser printers.
¾ To prevent special media such as transparencies and label sheets from sticking together,
remove them from the exit tray as they are printed.
¾ Place transparencies on a flat surface after removing them from the machine.
¾ Do not leave the film in the paper tray for long periods of time. Dust and dirt may
accumulate on them resulting in spotty printing.
¾ To avoid smudging caused by fingerprints, handle transparencies and coated paper
carefully.
¾ To avoid fading, do not expose the printed transparencies to prolonged sunlight.
o
o
o
o
¾ Store unused media at temperatures between 59 F and 86 F (15 C to 30 C). The relative
humidity should be between 10% and 70%.
¾ Do not load more than 10 sheets of special media into the Bypass Tray at a time.
Page 4-10
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
o
o
¾ Verify that your labels’ adhesive material can tolerate fusing temperature of 200 C (392 F)
for 0.1 second.
¾ Ensure that there is no exposed adhesive material between labels. Exposed areas can
cause labels to peel off during printing, which can cause paper jams. Exposed adhesive
can also cause damage to machine components.
¾ Do not feed a sheet of labels through the machine more than once. The adhesive backing
is designed for one pass through the machine.
¾ Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or
otherwise damaged.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 4-11
Page 4-12
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Sending an E-mail
The E-mail function allows you to send your documents as an E-mail message without going
to a PC. The document is sent to the recipient’s E-mail box as an attachment.
The document you want to send is scanned and then attached to the E-mail as an image file.
You can enter E-mail addresses by using the Alphabet Keyboard on the front of your machine,
or by retrieving them from the local address book using the Address Book key.
To use this function, the network and E-mail settings must be configured. A System
)
Administration Guide is provided with setup instructions for the E-mail. For more information
contact your System Administrator.
Document Feeder:
1
¾ Remove all staples and paper
clips prior to loading.
¾ Adjust the sliding document
Document
Guides
guides to the size required.
¾ Insert the originals neatly into the
Document Feeder, face up.
The first page should be on top
with the headings towards the
back or left of the machine.
¾ Align the stack with the left and
rear edges of the tray. Adjust the
guides to just touch the edges of
the originals.
L
Up to 50 sheets of 80 g/m2 (20lb bond) paper can be loaded. Weight ranges from 45 - 105 g/m2
(12.5 - 28lb). Sizes range from B5 to Legal (7” x 10” to 8.5” x 14” ). Refer to “Scanner and Copier
Specifications” on page 12-5 for full Document Feeder specifications.
Page 5-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Document Glass:
z When using the
Document Glass,
ensure there are
no documents in
the Document
Feeder.
¾ Raise the Document Feeder and
position the original face down on
the Document Glass.
Align with the registration arrow in
the rear left corner.
Leaving the
Document
Feeder open
while scanning
will affect the
image quality.
¾ Lower the Document Feeder.
Select the E-Mail Key and Features
2
z Only those
features relevant
to the machine
configuration will
be available.
¾ Press the [E-mail] key on the
Control Panel.
Original Type
E-mail key
¾ Press the E-mail feature key
required on the Control Panel.
¾ Basic features available for E-
mail jobs are 2 Sided, Original
Type, Color Original and
2 Sided
Color
Resolution.
Original
For information about all the
Resolution
)
available E-mail features, refer
¾ Using the Navigation Keys, select
the setting required for the
feature and press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 5-3
Enter the Sender’s Name
3
4
¾ The E-mail screen displays From
or My Login Name, depending on
the authentication setting.
From:
Enter the sender’s name using
the Alphabet Keyboard, and then
press the [Enter] key.
¾ If authentication has been set-up,
enter your Login Name and
Password.
For information about
)
authentication setup, contact
your System Administrator.
z The Global
Address Book
displays
Enter the Recipient’s E-mail Address
addresses
¾ The To screen displays. Enter the
recipient’s E-mail address and
then press the [Enter] key.
retrieved from the
system server.
For more
information about
the Global
You can directly enter an E-mail
address using the Alphabet
Keyboard. You can include
numbers in the E-mail address by
using the Numeric Keypad.
Address Book,
refer to “Using the
Book” on page 5-
Alphabet Keyboard
Enter Key
You can also
access the local
Address book by
pressing the
¾ If you have chosen to use a Local
or Global Address Book, type in
the beginning of the E-mail
[Address Book]
key. Select
address and press [Enter].
[Local] and press
[Enter].
The closest matching addresses
stored in the Address Book
display.
¾ Use the Navigation Keys to select
the required address and press
[Enter].
Page 5-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Entering Multiple Recipients
5
After entering the first recipient,
Another Address? displays.
¾ Select [Add] to add another
Another Address?
[Done]
address or [Done] to continue.
The maximum number of
addresses you can enter is 10.
¾ Press [Enter].
¾ Repeat the procedure until all
addresses have been entered.
Send to Myself
6
7
Send to Myself? displays.
¾ Select [Yes] to send a copy of the
E-mail to your own mail account.
Send to Myself?
[Yes]
¾ Select [No] if a copy is note
required.
¾ Press [Enter].
Review Addresses
Review Addresses? displays.
¾ Select [Yes] to review the
addresses you have entered, and
if necessary make changes.
Review Addresses?
[No]
¾ If a review is not required, select
[No].
¾ Press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 5-5
Enter a Mail Subject
8
9
Mail Subject displays.
¾ Enter a subject for the mailnote
using the Alphabet Keyboard.
Mail Subject:
¾ Press [Enter].
Select a File Type
Select File Type displays. Use
this option to select the type of file
you want to send.
Select File Type
[PDF]
¾ Select [PDF] for Portable
document Format, or [TIFF] for
Tagged Image Format.
¾ Press [Enter].
Press Start
10
¾ Press [Start] to send the E-mail.
¾ If the display shows [Scan
Another?], load the next original
on the Document Glass and
using the Navigation Keys select
[Yes]. Then press [Enter].
Navigation Keys
Start
Continue the procedure until all
the originals have been scanned.
¾ Select [No] when all the originals
have been scanned, and press
[Enter].
The E-mail is sent.
Page 5-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Basic E-mail Features
There are four basic E-mail features available. These features can be selected using the
feature keys located on the Control Panel.
Original Type
2 Sided
Color Original
Resolution
Feature Description
FEATURE
2 Sided
OPTIONS
INSTRUCTIONS
Yes
No
Select if your original is 2 ¾ Press [E-mail].
Sided.
¾ Press [2 Sided].
z Select if your
originals are2
Sided.
Select if your original is 1-
Sided.
¾ Use the Navigation Keys to select the option
required and press [Enter] to save the selection.
Original Type
Text
Use for documents
¾ Press [E-mail].
containing mostly text.
¾ Press [Original Type].
z Use to select the
type of
document being
scanned.
Mixed
Use for documents with
mixed text and graphics.
¾ Use the Navigation Keys to select the option
required and press [Enter].
Photo
On
Use for photographs.
Color Original
Use to scan a color
original and send to the
recipient.
¾ Press [E-mail].
¾ Press [Color Original].
z Use to scan and
send a color
original.
¾ Use the Navigation Keys to select [On] and press
z The remote recipient must
have the capability to
[Enter].
receive a color e-mail.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 5-7
Resolution
100 dpi Scans using a resolution ¾ Press [E-mail].
of 100 x 100 dots per inch
¾ Press [Resolution].
(dpi). Produces a lower
quality image which can ¾ Use the Navigation Keys to select the option
z Use to increase
sharpness and
clarity.
be processed quickly.
required and press [Enter].
200 dpi Scans using a resolution
of 200 x 200 dots per inch
(dpi). The default setting
which produces a good
quality image from most
text originals.
300 dpi Scans using a resolution
of 300 x 300 dots per inch
(dpi). Use this setting to
produce a higher quality
image if more definition is
required.
400 dpi Scans using a resolution
of 400 x 400 dots per inch
(dpi). Produces high
quality output ideal for
graphics and photos. May
take longer to process.
Page 5-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Special E-mail Features
The special E-mail features available can be accessed by pressing the Menu/Exit key and
then selecting E-mail Features on the display.
Menu/Exit
Enter
Navigation Keys
Feature Description
FEATURE
OPTIONS
TO SELECT
Group Mail
New
Use to create a new
¾ Press [Menu/Exit]. Select [E-mail Features] and
Group.
press [Enter].
z You can store
several E-mail
address in a
¾ Select [Group Mail] and press [Enter].
specific Group.
¾ Select [New] and press [Enter].
¾ Enter a Group Name using the Alphabet
Keyboard and press [Enter].
If a Group Name is not entered, a Group Number
displays.
¾ Enter an E-mail address to be included in the
Group using the Alphabet Keyboard and press
[Enter]. You can include numbers in the e-mail
address by using the Numeric Keypad. Press
[Enter].
¾ When the display shows [Another Address?],
select [Add] and press [Enter].
¾ Continue to add addresses until all the recipients
have been added to the Group, and select [Done]
and press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 5-9
Edit
Use to edit an existing
Group.
¾ Press [Menu/Exit]. Select [E-mail Features] and
press [Enter].
¾ Select [Group Mail] and press [Enter].
Delete
Use to delete an existing
Group.
¾ Select [Edit] or [Delete] and press [Enter].
¾ Enter a Group Number or Name and press
[Enter].
¾ If editing, change the Group Name, Add or Delete
addresses, and change the File Type as required.
Press [Enter].
¾ If deleting, a confirmation window appears. Select
[Yes] and press [Enter].
Send
Use to send E-mails to a ¾ Load the originals and press the [E-mail] key.
Group.
¾ Press [Menu/Exit]. Select [E-mail Features] and
press [Enter].
¾ Select [Group Mail] and press [Enter].
¾ Select [Send] and press [Enter].
¾ Enter the Group Number and press [Enter].
¾ Enter the Sender’s name and select other
features as required.
¾ Press [Start] to activate the job.
Page 5-10
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Local Address
Book
New
Edit
Use to add entries to the ¾ Press [Menu/Exit]. Select [E-mail Features] and
Local Address book.
press [Enter].
¾ Select [Local Address Book] and press [Enter].
¾ Select [New], [Edit] or [Delete] and press [Enter].
Use to edit entries
contained in the Local
Address book.
z You can store
frequently used
E-mail
addresses in the
machine’s
memory, in the
Local Address
Book.
¾ For new entries, enter the name using the
Alphabet Keyboard and press [Enter]. Then enter
the E-mail address and press [Enter]
Delete
Use to delete entries from
the Local Address Book.
¾ To edit or delete an entry, scroll to the required e-
mail address and press [Enter].
If the selected address is one of the authorized
)
users registered by the system administrator or an
address from Group mail, “Entry Not Editable”
displays.
¾ To add. edit or delete another e-mail address,
repeat the procedure.
Send
Use to send to E-mail
addresses stored in the
Local Address book.
¾ Load the originals and press the [E-mail] key.
¾ Press [Menu/Exit]. Select [E-mail Features] and
press [Enter].
¾ Select [Local Address Book] and press [Enter].
¾ Select [Send] and press [Enter].
¾ Type the first few letters of the E-mail address
required and press [Enter]. The closest matches
display. Select the required address using the
Navigation Keys and press [Enter].
¾ Select another address if required. [Press Enter].
¾ Enter the Sender’s name and select other
features as required.
¾ Press [Start] to activate the job.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 5-11
Print Address
Book
Individual Use to print a list of
Address individual E-mail
addresses.
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [E-mail
Features] and press [Enter].
z Use this feature
to print a list of
individual, group
or all E-mails
stored in the
Local Address
book.
Group
Use to print a list of the E-
¾ Select [Print Address Book] and press [Enter].
¾ Select the required option and press [Enter].
The selected list prints.
Address mail Groups.
All
Use to print both the
Individual and Group E-
mail address lists.
Page 5-12
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Using the Global Address Book
The Global Address Book has to be set up to retrieve E-mail address from a LDAP. The Global
Address Book works in a similar way to the Local Address Book, except you cannot add, edit
or delete users.
¾ Load the originals and press the [E-mail] key.
1
2
3
¾ To access the Global Address Book press the [Address Book] key and select [Global].
¾ Begin to enter the E-mail address in the To: field.
¾ when a few characters have been entered, press [Enter]. The machine will search for E-
mail addresses on the LDAP server which match the characters entered.
If you have not entered enough characters, a message displays requesting more
characters.
A list of E-mail addresses which match the characters entered displays.
¾ Using the Navigation Keys, scroll through the list of addresses and find the correct
address. Then press [Enter].
¾ Use [Add] to enter another address if required, the maximum number of addresses you
4
5
can enter is 10.
¾ After entering all the addresses, select [Done] and press [Enter].
¾ Enter the Sender’s name and select other features as required.
¾ Press [Start] to activate the job.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 5-13
Page 5-14
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Faxing Procedure
Load the Originals
1
Document Feeder:
¾ Remove all staples and paper
clips prior to loading.
¾ Adjust the sliding document
Document
Guides
guides to the size required.
¾ Insert the originals neatly into the
Document Feeder, face up.
The first page should be on top
with the headings towards the
back or left of the machine.
¾ Align the stack with the left and
rear edges of the tray. Adjust the
guides to just touch the edges of
the originals.
L
Up to 50 sheets of 80 g/m2 (20lb bond) paper can be loaded. Weight ranges from 45 - 105 g/m2
(12.5 - 28lb). Sizes range from B5 to Legal (7” x 10” to 8.5” x 14” ). Refer to “Scanner and Copier
Specifications” on page 12-5 for full Document Feeder specifications.
Page 6-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Document Glass:
z Ensure no
documents are
loaded in the
Document
¾ Raise the Document Feeder and
position the original face down on
the Document Glass.
Feeder when
using the
Document Glass.
Align with the registration arrow in
the rear left corner.
Leaving the
Document
¾ Lower the Document Feeder.
Feeder open
while scanning
will affect the
image quality and
toner
consumption.
z On completion of
the job, ensure
the Document
Feeder is closed.
Select the Fax key
2
Fax Key
¾ Press the [Fax] key to activate
Fax mode.
The Fax key remains illuminated
when selected.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-3
Select the Fax Features
3
z For more
information about
the available Fax
features, refer to
“Basic Fax
Features” on
page 6-8, and
“Special Fax
Features” on
¾ Press the Fax feature key
Lighten/Darken
Original Type
required on the Control Panel.
Basic features available for Fax
jobs are Lighten/Darken, 2 Sided,
Original Type, Color Original and
Resolution.
2 Sided
For information about all the
available Fax features, refer to
Color
Original
)
Resolution
¾ Using the Navigation Keys, select
the setting required for the
feature and press [Enter].
Enter the Fax Number
4
z There are several
methods
¾ Use the Numeric Keypad to enter
the telephone number of the
remote fax machine.
available for
entering the
remote fax
number, for more
information refer
¾ If an incorrect number is entered,
use the Navigation Keys to select
the incorrect number and then
press the correct number.
Numeric Keypad
Clear/Clear All
Pressing the [Clear/Clear All] key
will delete the entire fax number
entered.
Page 6-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Press Start
5
6
¾ Press [Start] to begin the Fax job.
¾ If the display shows [Scan
Another?] and another original
requires scanning, load the next
original and select [Yes]. Press
[Enter].
Navigation Keys
Start
Continue the procedure until all
the originals have been scanned.
¾ Select [No] when all the originals
have been scanned, and press
[Enter].
The Fax is scanned and sent.
Job Status
¾ To view the status of a job, press
the [Job Status] key.
Job Status
¾ A list of current jobs and the job
details displays.
¾ To add a page to a job, select the
required job using the Navigation
Keys and press [Enter]. Load the
original and select [Add Page?]
and press [Enter].
Enter
¾ To delete a job, select the
required job and press [Enter].
Select [Cancel Job?] and press
[Enter]. A confirmation message
displays, select [1:Yes] and press
[Enter].
Navigation Keys
¾ Press [Menu/Exit] to exit Job
Status.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-5
Dialing Methods
There are several methods which can be used to enter a fax number or a group of fax number.
The following table identifies and explains all the dialing methods available.
DIALING METHOD
Keypad Dialing
INSTRUCTIONS
¾ Load the originals and select the [Fax] key.
¾ Use the Numeric Keypad to enter the telephone number of the
z Use when entering the remote fax
number using the Numeric Keypad.
remote fax machine.
¾ Press [Start] to send the fax.
Speed Dialing
¾ Load the originals and select the [Fax] key.
¾ Program the features required for the job.
¾ Press [Speed Dial] and enter the Speed Dial number (1-200).
z Use to access a fax number which
has previously been stored in the
machine’s memory.
The name appears and the original is scanned into memory
ready for sending.
¾ If the original is loaded on the Document Glass, the display
asks if you want to send another page. Select [Yes] to add more
originals, or [No] to begin transmission. Press [Enter].
The fax number stored in the speed dial location will be dialed
automatically and the fax is sent.
Group Dialing
¾ Load the originals and select the [Fax] key.
¾ Program the features required for the job.
z Use to access a group of numbers
which have previously been stored in
the machine’s memory.
¾ Press [Group Dial] and enter the Group Dial number (1-200).
¾ When the required number displays, press [Enter].
The original is scanned into memory.
¾ If the original is loaded on the Document Glass, the display
asks if you want to send another page. Select [Yes] to add more
originals, or [No] to begin transmission. Press [Enter].
The machine automatically sends the fax to each of the
numbers in the Group.
Page 6-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Manual group dialing
¾ Load the originals and select [Fax].
¾ Press [Manual Group].
z Use to manually program a broadcast
send to multiple destinations.
The display requests a destination fax number.
¾ Enter the first fax number and press [Enter].
¾ ’Another No.?’ displays. Select [Yes] to add another number
and press [Enter].
¾ Repeat the procedure until all numbers have been entered.
Then select [No] and press [Enter].
The originals are scanned and faxed to the destinations
entered.
Manual Dialing
¾ Load the originals and select [Fax].
¾ Press [Manual Dial].
z Use to dial the fax number with the
telephone line open.
The dial tone is audible and the LCD displays ’Phone’.
¾ Dial the fax number. When the fax tone is heard, press [Start] to
begin faxing.
Redial
¾ Load the originals and select [Fax].
¾ Press [Pause/Redial].
z Numbers which have already been
entered recently can be quickly
The last number is automatically dialled and the originals are
scanned and faxed.
accessed using the Redial function.
¾ Load the originals and select [Fax].
¾ Press [Pause/Redial] for approximately 2 seconds.
The Redial Memory in the machine retains the last 10 numbers
dialled.
¾ Using the Navigation Keys, select the number required and
press [Enter].
¾ Press [Start] to dial the number. The fax is automatically
scanned and sent.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-7
Basic Fax Features
There are five basic Fax features available. These features can be selected using the feature
keys located on the Control Panel.
Original Type
Lighten / Darken
2 Sided
Color Original
Resolution
Feature Description
FEATURE
OPTIONS
INSTRUCTIONS
Lighten/Darken 5 Contrast Settings
¾ Press [Fax].
¾ Press [Lighten/Darken].
z Useto adjust the
contrast for a
document
¾ Using the Navigation Keys select a contrast
containing faint
or dark images.
setting.
Each time the key is pressed the selection block
on the display moves to the left or right. As the
selection block moves to the right the contrast
becomes darker.
¾ Press [Enter] to save the selection.
2 Sided
Yes
No
Select if your original is 2 ¾ Press [Fax].
Sided.
¾ Press [2 Sided].
z Select if your
originals are2
Sided.
Select if your original is 1-
Sided.
¾ Using the Navigation Keys, select the option
required and press [Enter].
Page 6-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Original Type
Text
Use for documents
¾ Press [Fax].
containing mostly text.
¾ Press [Original Type].
z Use to select the
type of
document being
scanned.
Mixed
Use for documents with
mixed text and graphics.
¾ Using the Navigation Keys, select the option
required and press [Enter].
Photo
On
Use for photographs.
Color Original
Use to scan a color
original and send to the
remote fax.
¾ Press [Fax].
¾ Press [Color Original].
z Use to scan and
send a color
original.
¾ Using the Navigation Keys, select the [On] and
z The remote fax must have
the capability to receive a
color fax to use this
feature.
press [Enter].
Resolution
Standard Use for documents with
¾ Press [Fax].
normal sized characters.
¾ Press [Resolution].
z Use to increase
sharpness and
clarity.
Fine
Use for documents
containing small
characters or thin lines.
Also used when sending a
color fax.
¾ Using the Navigation Keys, select the option
required and press [Enter].
Super Fine Use for documents
containing extremely fine
detail. This is available
only if the remote
machine also supports
Super Fine resolution.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-9
Special Fax Features
The special Fax features available can be accessed by pressing the Menu/Exit key and then
selecting Fax Features on the display.
Menu/Exit
Enter
Navigation Keys
Feature Description
FEATURE
Toll Save
OPTIONS
INSTRUCTIONS
Off
On
Use to de-activate the
feature.
¾ Press [Menu/Exit].
¾ Using the Navigation keys select [Fax Features]
z Use to set a low
rate period for
sending faxes.
and press [Enter].
Use to enable the feature.
¾ Select [Toll Save] and press [Enter].
¾ Select [On] and press [Enter].
¾ Select [Start Time] and enter a date and time to
start the Toll Save period. Press [Enter].
¾ Select [End Time] and enter a date and time to
end the Toll Save period. Press [Enter].
Page 6-10
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Memory Fax
No.
Used to enter the fax
phone number for the
remote machine.
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [Fax Features]
z Use to send a
fax from
memory.
and press [Enter].
¾ Select [Memory Fax] and press [Enter].
¾ Enter the fax number for the remote machine.
Press [Enter].
¾ Another No? displays, if required enter another
number and press [Enter].
¾ When all the numbers have been entered the
originals are scanned and stored in memory. The
fax is then sent from memory.
Delay Fax
-
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [Fax Features]
z Use to set a
specific time for
sending your
fax.
and press [Enter].
¾ Select [Delay Fax] and press [Enter].
¾ Enter the fax number using the Numeric Keypad
or Speed Dial, and press [Enter]. Enter another
number if required. When all numbers have been
entered select [No] and press [Enter].
¾ Enter a name for the job and press [Enter].
¾ The displays shows the current time, enter a time
for the delay fax and press [Enter].
If you set a time earlier than the current time, the
job will be sent at that time the following day.
The originals are scanned into memory ready for
sending.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-11
Priority Fax
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [Fax Features]
z Use this option
to send your fax
ahead of
and press [Enter].
reserved
operations.
¾ Select [Priority Fax] and press [Enter].
¾ Enter the fax number using the Numeric Keypad
or Speed Dial, and press [Enter]. Enter another
number if required. When all numbers have been
entered select [No] and press [Enter].
¾ Enter a name for the job and press [Enter].
The originals are scanned into memory ready for
sending.
Polling
TX Poll Use to store a document ¾ Press [Menu/Exit].
on the machine ready to
be polled by a remote fax
machine.
¾ Using the Navigation Keys select [Fax Features]
z Polling is used
to retrieve
documents from
remote fax
and press [Enter].
¾ Select [Polling] and press [Enter].
¾ Select [TX Poll] and press [Enter].
¾ Enter a 4 digit Poll Code and press [Enter].
machines.
Remote fax
machines can
also poll your
machine.
¾ To store the originals in the Bulletin Board select
[On]. If the Bulletin Board is not required, select
[Off].
¾ Press [Start]. The originals are scanned into
memory ready to be polled.
Page 6-12
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Delay RX Use to retrieve a
¾ Press [Menu/Exit].
Poll
document from a remote
fax machine at a specified
time.
¾ Using the Navigation Keys select [Fax Features]
and press [Enter].
¾ Select [Polling] and press [Enter].
¾ Select [Delay RX Poll] and press [Enter].
¾ Enter the fax number using the Numeric Keypad
or Speed Dial, and press [Enter].
¾ The display shows the current time, enter a start
time for the remote fax machine to be polled.
Press [Enter] when the correct time displays.
If you set a time earlier than the current time, the
job will be sent at that time the following day.
¾ Enter a 4 digit Poll Code and press [Enter].
The machine will poll the remote machine at the
specified time.
Batch TX
On
Off
Activates the Batch TX
feature.
¾ Press [Menu/Exit].
¾ Using the Navigation Keys select [Fax Features]
z Use to send
faxes that are
going to the
samelocation,in
one batch.
and press [Enter].
Deactivates the Batch TX
feature.
¾ Use the Navigation Keys to select [Batch TX] and
press [Enter].
¾ Select [On] and press [Enter]. Enter a Batch
Interval between 0 - 99 and press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-13
Mailbox
This feature allows you to store a document in a mailbox, delete a document from a mailbox,
print a document from a mailbox and to poll a mailbox. Mailboxes are setup by the System
Administrator.
Instructions for setting up Mailboxes are located in the System Administration Guide provided
)
with your Xerox WorkCentre M20i.
Storing Documents in a Mailbox
¾ Load the originals you want to
1
store in the mailbox.
¾ Press the [Menu/Exit] key.
Menu/Exit
Enter
¾ Using the Navigation Keys select
2
[Mailbox] and press [Enter].
Fax Features
Æ Mailbox
¾ Select [Store] and press [Enter].
¾ Enter the box number for the
3
mailbox and press [Enter].
Mailbox No:
The originals are scanned and
stored in the mailbox. The display
shows the number of pages
stored.
Page 6-14
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Printing Mailbox Contents
¾ Press the [Menu/Exit] key.
1
¾ Using the Navigation Keys select
[Mailbox] and press [Enter].
Menu/Exit
Enter
¾ Select [Print] and press [Enter]
2
Mailbox
[Print]
¾ Enter the box number for the
3
mailbox and press [Enter].
Mailbox No:
¾ Enter the passcode for the
mailbox and press [Enter].
The contents of the mailbox are
printed and deleted.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-15
Deleting Mailbox Contents
¾ Press the [Menu/Exit] key.
1
¾ Using the Navigation Keys select
[Mailbox] and press [Enter].
Menu/Exit
Enter
¾ Select [Delete] and press [Enter]
2
Mailbox
[Delete]
¾ Enter the box number for the
3
mailbox and press [Enter].
Mailbox No:
¾ Enter the passcode for the
mailbox and press [Enter].
The contents of the mailbox are
deleted.
Page 6-16
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Polling from a Mailbox
¾ Press the [Menu/Exit] key.
1
¾ Using the Navigation Keys select
[Mailbox] and press [Enter].
Menu/Exit
Enter
¾ Select [Poll From] and press
2
3
4
[Enter]
Mailbox
[Poll From]
¾ Enter the box number to be polled
and press [Enter].
Mailbox No:
¾ Enter the passcode for the
mailbox and press [Enter].
¾ Enter a remote fax number and press [Enter].
¾ The display shows the current time. Enter a start time for the mailbox to be polled and
press [Enter].
If you set a time earlier than the current time, the originals will be retrieved at that time
the following day.
The mailbox will be polled at the specified time.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-17
Sending to a Mailbox
¾ Press the [Menu/Exit] key.
1
¾ Using the Navigation Keys select
[Mailbox] and press [Enter].
Menu/Exit
Enter
¾ Select [Send] and press [Enter]
2
3
4
Mailbox
[Send]
¾ Enter the box number for where
the originals are to be sent, and
press [Enter].
Mailbox No:
¾ Enter the passcode for the
mailbox and press [Enter].
¾ Enter a remote fax number and press [Enter].
¾ The display shows the current time. Enter a start time for the originals to be sent and
press [Enter].
If you set a time earlier than the current time, the job will be sent at that time the
following day.
The originals will be sent to the mailbox at the specified time.
Page 6-18
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Fax Setup Options
Changing the Fax Setup Options
¾ Press the [Machine Status] key.
1
Enter Machine
Status
¾ Using the Navigation Keys select
2
[Fax Setup] and press [Enter].
Machine Setup
Æ Fax Setup
¾ Using the Navigation Keys select
3
the required setup option and
press [Enter].
Fax Setup
[Lighten/Darken]
starting on page 6-20 customize
the settings to meet your
requirements.
¾ Press [Enter] to save your
selections.
¾ Press [Menu/Exit] to exit each menu level and return to standby mode.
4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-19
Fax Setup Options
The following table lists all the Fax Setup options available and provides a instructions for
customizing each setting. Instructions for accessing the Fax Setup options are provided on
OPTION
Lighten/Darken
Resolution
SETTINGS
5 Contrast Settings
Standard
DESCRIPTION
Use to set the default Lighten/Darken setting.
Use to set the default resolution for fax jobs.
Fine
Super Fine
Tel
Receive Mode
Use to operate in manual mode. When a call is
received pick up the external phone handset or
press [Manual Dial]. If a fax tone can be heard,
press [Start] and replace the handset.
Fax
The machine answers the incoming call and
immediately switches to fax receive mode.
Ans/Fax
Use if attaching an answering machine to the
machine. If the machine detects a fax tone, it
switches to fax mode automatically.
Fax Duplex
Off
Use to de-activate Fax Duplex.
Long Edge
Use to set fax jobs to print 2 sided, with the
binding edge on the long edge.
Short Edge
Use to set fax jobs to print 2 sided, with the
binding edge on the short edge.
Page 6-20
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Speed Dials
New
¾ Enter a speed dial number using the Numeric
Keypad and then press [Enter].
If a number is already stored in the location a
message displays. Enter a different Speed
Dial number.
¾ Enter the fax number you want to store using
the Numeric Keypad and press [Enter].
To insert a pause press the [Pause/Redial]
key and a ’P’ appears on the display.
¾ To assign a name, enter the required name
using the Numeric Keypad. If you do not
require a name leave empty and press
[Enter].
To store more Speed Dial numbers repeat
the procedure.
Edit
¾ If you want to delete a specific Speed Dial
number from the group, press the [Speed
Dial] key and enter the number. The display
shows [Delete].
Delete
To add a new number, press the [Speed Dial]
key and enter the number, the display shows
[Add].
¾ Press [Enter]. Repeat the procedure until all
the editing has been completed.
¾ Press the [Menu/Exit] key when you have
finished editing. The name appears in the
upper line of the display. Change the name
if required and press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-21
Group Dials
New
¾ Enter a Group number between 1 and 200
using the Numeric Keypad and then press
[Enter].
If a number is already stored in the location a
message displays.
¾ The display asks you to enter a Speed Dial
number to add to the Group. Enter the
number and then press [Enter].
¾ Continue entering Speed Dial numbers until
all the group members have been added.
Press the [Menu/Exit] key when you have
finished entering numbers.
¾ To assign a name to the Group, enter the
required name. If a name is not required.
Press [Enter].
¾ To assign another Group, repeat the
procedure.
Edit
¾ If you want to delete a specific Speed Dial
number from the Group, press the [Speed
Dial] key. The display shows [Delete].
Delete
To add a new number, press the [Speed Dial]
key, the display shows [Add].
¾ Press [Enter]. Repeat the procedure until all
the editing has been completed.
¾ Press the [Menu/Exit] key when you have
finished editing. The name appears in the
upper line of the display. Change the name
if required and press [Enter].
MSG Confirm
On
Sets the machine to print a transmission report
for every fax transmission.
Off
De-activates printing a transmission report.
On-Err
Sets the machine to print a transmission report
only if an error has occurred.
Page 6-22
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Auto Reduction
On
Off
Use to activate the machine performing an
automatic reduction for over-sized fax jobs.
Use to de-activate the automatic reduction.
Over-sized jobs are printed on two pages.
Prefix Dial
Up to 5 digits
The number entered will be added to the
beginning of each fax sent.
Auto Report
On
Off
On
Use to enable a report listing details about the
previous 50 communication operations.
ECM Mode
Use to switch on ECM for all transmissions.
Transmission time may be increased when
ECM is enabled.
Off
Use to switch off ECM.
Redials
[0 - 13]
[1 - 7]
Use to set the number of redial attempts.
Ring to Answer
Use to set the number of rings before
answering.
Redial Term
Ringer
[1 - 15]
Use to set the number of minutes between
redial attempts.
Off
Low
Med
High
On
Use to set the ringer volume.
Junk Fax Setup
Secure Receive
Use to restrict receipt of junk mail by only
allowing faxes to be received from remote
machines registered on your machine.
Off
On
Off
Use to set the default option for receiving
secure faxes.
Print
Fax Auto Tray
Tray 1
Tray 1 & Tray 2
All
Selects the default paper tray for fax jobs.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 6-23
Dial Mode
Tone
Selects the default dial mode.
Pulse
Page 6-24
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
7 Print
Direct Printing using a USB or Parallel Port connection is
available as standard on the Xerox WorkCentre M20 and as an
option on the Xerox WorkCentre M20i. Networked Printing is
available as standard on the Xerox WorkCentre M20i and is
optional on the Xerox WorkCentre M20.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 7-1
Printing a Document
The Xerox WorkCentre M20 and M20i supports printing from these operating systems:
Windows XP
Windows 2000
-
-
-
-
Windows NT V4.0
Windows 98/Millennium Edition
Your Workstation and the Xerox WorkCentre M20 or M20i must be connected and configured
for printing from these environments.
There are two printer drivers supplied, a PostScript driver and a PCL driver.
Instructions for loading drivers and connecting the machine via USB or Parallel port are provided
)
in the Getting Started chapter. For network connections, refer to the System Administration
Guide supplied with your Xerox WorkCentre M20i, or contact your System Administrator.
Prior to printing, ensure all relevant connections have been made, the machine is powered on
and there is paper in the paper tray.
¾ Start the program you are using to create the document and create or open the document
1
2
requiring printing.
¾ Select [Print] or [Print Setup] from the File menu.
Ensure that Xerox WC M20 Series is selected as your default printer.
¾ Select [Properties] if you want to make any programming selections for your print job.
3
4
¾ Select [OK] to close the Properties dialog box.
¾ Select [OK] to process and send the print job.
The job will automatically be printed on your machine.
Page 7-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Printer Settings
Most Windows software applications allow you to make changes to the printer settings. This
includes settings that determine how a print job looks such as paper size, paper orientation,
and margins.
Settings made in the application to create the document will usually override settings made in
the printer driver.
You do not need to use any of the control panel keys to use the machine as a printer. For
)
example, if you want to adjust the printing contrast you select the settings in the printer driver,
not the Lighten/Darken feature on the machine’s control panel.
Accessing Printer Settings
You can access printer settings by using either of these methods.
Windows 98/Me
¾ Select File > Print > Properties or File > Print Setup from within any Windows application.
OR
¾ Select Xerox WC M20 Series printer from the Printers folder, then select File > Properties
(or select the printer icon in the Printers folder, and click the right mouse button).
Windows NT 4.0
¾ Select File > Print > Properties or File > Print Setup from within any Windows application.
OR
¾ Select Xerox WC M20 Series printer from the Printers folder, click the right mouse button,
then select Document Defaults from the drop-down list.
Windows 2000
¾ Select File > Print from within any Windows application.
OR
¾ Select Xerox WC M20 Series printer from the Printers folder, click the right mouse button,
then select Properties and Printing Preferences from the drop-down list.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 7-3
Windows XP
¾ Select File > Print > Properties from within any Windows application.
¾ Select Xerox WC M20 Series printer from the Printers and Faxes folder, click the right
mouse button, then select Printing Preferences from the drop-down list.
Page 7-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
PCL Driver
When the Printer Properties are displayed, the print job settings can be reviewed and
changed. The Properties window consists of six tabs:
-
-
-
-
-
-
Layout
Paper
Image Options
Output Options
Watermark
About
If the Printer Properties are accessed through the Printers folder, additional Windows-based
tabs are available.
For information on the Windows-based tabs, refer to documentation provided with Windows.
)
For detailed information about the printer settings available on each tab, please refer to the
printer driver on-line Help.
If you access Printer Properties through the Printers folder, any settings made will become the
)
default settings for the printer. Settings made when Printer Properties are accessed through an
application File menu and Print or Print Setup will remain active until the application you are
printing from is closed.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 7-5
Layout Tab
Portrait
Landscape
Use to print across the width
of the page, letter style.
Use to print across the length
of the page, spreadsheet
style.
Rotate 180 Degrees
Favorites
Use to rotate the images 180
degrees.
Use this option to store
your selections for a
particular job. After making
selections, enter a job title
in the window and select
[Save].
Long Edge
Use this option when you require 2
sided output in a Book orientation.
Help
Short Edge
Use to access the
Help system which
provides detailed
information about all
the Print Driver
features.
Use this option when you require 2
sided output in a Calendar
orientation.
OK
Cancel
More Layout Options
Apply
Use to accept
the selections
made and
close the
dialog.
Closes the dialog and
returns all settings to the
values in place before the
dialog was opened.
Provides access to additional layout
Saves all the selections
made without closing the
dialog.
features such as multiple pages per side,
poster, booklet printing, fit to page and
reduce/enlarge.
Page 7-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Paper Tab
Size
Print Quantity
Use to select the size of paper
required from the drop down
menu.
Use to select the number of
prints required.
Custom
Use to enter a
customized paper size.
Type
Use to select the type of
paper required.
Cover Page
Source
Use to select the required
paper source for a cover
page.
Use to select the required
paper source for the job.
Banner Page
Use to select whether a banner
page is required.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 7-7
Image Options Tab
Print Quality Mode
Use to select the print resolution. 1200
dpi produces the highest quality output,
300 dpi is the lowest.
Image Quality
Use to select the Image
Quality setting to apply to
the job. The options
available depend on the
resolution selected.
Toner Save Mode
Use to activate Toner
Save mode. Produces a
lower quality output and
uses less toner.
Graphic Options
Provides access to additional options which allow you to
select to print your output as graphics or bitmaps. You can
also select to print all text in black.
Page 7-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Output Options Tab
Print Order
Use to select a sequence for your print
job. Select whether to reverse all pages,
print odd pages or print even pages.
Use Print Fonts
If this option is selected
the fonts which are
resident on the printer will
be used for the job.
Collate
Select to produce
collated output
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 7-9
Watermark Tab
Current Watermarks
Watermarks are background images which print on each page.
They are useful for adding information such as Draft or
Confidential, or the name of your company. Select the Watermark
required from the list shown, or create a new Watermark.
Add, Update and Delete
Use these options to create
new Watermarks, edit
Watermarks or Delete a
Watermark.
Font Attributes
Watermark Message
Select the font type, style,
size and greyscale to use
for your Watermark.
Use this window to enter
the text you would like to
add as a Watermark.
First Page Only
Select this option if you
want the Watermark to print
on the first page only, and
not the rest of the
Message Angle
document.
Select to print the
Watermark horizontally,
vertically or a specified
angle.
Page 7-10
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
About Tab
The About Tab provides information about the printer driver. It provides the program version
number and copyright information relating to the printer driver. Clicking on this page will
connect you to the Xerox website, provided you have access to the Internet
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 7-11
PostScript Driver
When the Printer Properties are displayed, the print job settings can be reviewed and
changed. The Properties window consists of two tabs:
-
-
Layout
Paper/Quality
If the Printer Properties are accessed through the Printers folder, additional Windows-based
tabs are available.
For information on the Windows-based tabs, refer to documentation provided with Windows.
)
For details on the printer settings available on each tab, please refer to the printer driver on-
line Help.
If you access Printer Properties through the Printers folder, any settings made will become the
)
default settings for the printer. Settings made when Printer Properties are accessed through an
application File menu and Print or Print Setup will remain active until the application you are
printing from is closed.
Page 7-12
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Layout Tab
Landscape
Portrait
Use to print across the length
of the page, spreadsheet
style.
Use to print across the width
of the page, letter style.
Rotated Landscape
Pages Per Sheet
Use if the image requires
rotating to landscape format.
Use to select to print
multiple images on one
sheet or to select Booklet
mode.
Flip on Long Edge
Use this option when you require 2
sided output in a Book orientation.
Advanced
Flip on Short Edge
Provides access to
additional features.
Use this option when you require 2
sided output in a Calendar
orientation.
Cancel
Page Order
OK
Apply
Closes the dialog and
returns all settings to
the values in place
before the dialog was
opened.
Use to print in forward or reverse Use to accept the
Saves all the selections
made without closing the
dialog.
order.
selections made
and close the
dialog.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 7-13
Paper / Quality Tab
Paper Source
Use to select the paper source for
the print job from the drop down
menu.
Page 7-14
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
TWAIN Scanner Program
The Xerox WorkCentre M20 and M20i TWAIN Scanner program is used to scan images,
graphics, photographs, and printed text. Documents can be fed from the Document Feeder or
placed on the Document Glass.
The TWAIN driver is a program for PC printing that supports Windows 98, Windows NT4.0,
Windows 2000, Windows ME and Windows XP environments. Using an independent protocol
and the USB or parallel port, the TWAIN driver converts the scanned image into a standard
format that you can edit.
Page 8-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Scanning Procedure
Open the Image Editing Application
1
z For instructions
on loading media,
¾ Open your image editing
application and acquire the
WorkCentre M20 TWAIN
Scanner.
For full media
specifications
This feature allows you to convert
hard copy images into electronic
images that you can use in other
documents.
Load the Originals
32
Document Feeder:
¾ Remove all staples and paper
clips prior to loading.
¾ Adjust the sliding document
Document
Guides
guides to the size required.
¾ Insert the originals neatly into the
Document Feeder, face up.
The first page should be on top
with the headings towards the
back or left of the machine.
¾ Align the stack with the left and
rear edges of the tray. Adjust the
guides to just touch the edges of
the originals.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 8-3
z When using the
Document Glass,
ensure there are
no documents in
the Document
Feeder.
L
Up to 50 sheets of 80 g/m2 (20lb bond) paper can be loaded. Weight ranges from 45 - 105 g/m2
(12.5 - 28lb). Sizes range from B5 to Legal (7” x 10” to 8.5” x 14” ). Refer to “Scanner and Copier
Specifications” on page 12-5 for full Document Feeder specifications.
Document Glass:
Leaving the
Document
Feeder open
while scanning
will affect the
image quality.
¾ Raise the Document Feeder and
position the original face down on
the Document Glass.
Align with the registration arrow in
the rear left corner.
¾ Lower the Document Feeder.
Select the Scan Features
3
z For Scanner
specifications
refer to “Scanner
and Copier
¾ Select [New Scan] in your
application to access the TWAIN
driver options.
¾ Customize the settings available
on the TWAIN driver for the job,
for example Image Input,
Resolution, and Reduce/Enlarge.
Page 8-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Select Preview
4
¾ Select the Preview option on the
TWAIN driver window.
The image appears on the
screen. This gives you the
opportunity to select the specific
area you wish to scan.
¾ If necessary, drag the selection
tool to the area requiring
scanning.
Preview
Select Scan
5
6
¾ Select the Scan option on the
TWAIN driver window.
The specified image displays on
the screen.
Scan
Save the Image
¾ Select [File] and [Save].
The image is saved and can now
be used in another document if
required.
¾ Remove your original from the
Document Glass or Document
Feeder.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 8-5
Page 8-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Machine Setup
Use the following instructions to customize your machine to meet your individual
requirements.
¾ Press the [Machine Status] key.
1
Enter Machine
Status
¾ Using the Navigation Keys select
[Machine Setup] and press
[Enter].
2
3
Æ Machine Setup
Fax Setup
¾ Using the Navigation Keys select
the required setup option and
press [Enter].
Machine Setup
[Tray 1 Size]
customize the settings to meet
your requirements.
¾ Press [Enter] to save your
selections.
¾ Press [Menu/Exit] to exit each menu level and return to standby mode.
4
Page 9-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Machine Setup Options
OPTION
SETTINGS
DESCRIPTION
Tray 1 Size
LTR / A4 / LGL / Folio Use to set the default paper size for Tray 1.
Paper Size options are Letter, A4, Legal (216 x
356 mm / 8.5 x 14 inch) or Folio.
Tray 2 Size
LTR / A4 / LGL / Folio Use to set the default paper size for Tray 2.
Paper Size options are Letter, A4, Legal (216 x
356 mm / 8.5 x 14 inch) or Folio.
Bypass Size
LTR / A4 / LGL / Folio / Use to set the default paper size for the Bypass
A5 / Statement
tray. Paper Size options are Letter, A4, Legal
(216 x 356 mm / 8.5 x 14 inch), Folio, A5 or
Statement.
L
If feeding media smaller than A4/Letter through
the bypass tray, the setting can remain set at
A4, Letter or Legal size.
When copying onto a paper size smaller than
A4/Letter, the printed image may be offset and
not reproduce correctly, even when Auto Fit is
selected.
Power Save
Time Out
On
Off
Use to enable the Power Save feature. If On is
selected, set the period of time the machine
waits before Power Save is activated. Choose
between 5, 10, 15, 30 or 45 minutes.
15 / 30 / 60 / 180
Seconds
Sets the number of seconds the machine
remains idle before the current job settings are
reset back to the default settings. Use Off to
deactivate the option.
Off
Stamp RX Name
On
Off
Set to On to enable sender information, the
machine ID, the page number, the date and time
of reception and the reduction rate of the image
to be printed on each page of each received
transmission. The information is printed on the
bottom edge of each page.
Alarm Sound
On
Off
Set to On to enable an alarm sound when an
error occurs or a fax communication ends.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-3
OPTION
Key Sound
SETTINGS
On
DESCRIPTION
Set to On to enable a sound when any key is
pressed.
Off
Speaker Control
Language
On
The speaker can be set to On, Off or Comm.
Comm allows the speaker to remain on until the
remote machine answers.
Off
Comm
English, French,
German, Italian,
The display uses the language selected.
Spanish, Portuguese,
Dutch, Danish, Swedish,
Finnish, Norwegian,
Russian
Localization
Inch
MM
Use to set whether measurements are
displayed and entered in inches or millimeters.
UK, Greece, Turkey, Ukraine,
Slovenia, Russia, Yugoslavia,
Australia, HongKong,
Select Country
Setting the Country option sets the correct fax
communication settings for each country.
NewZealand, SouthAfrica,
Israel, Korea, K.Xerox, China,
India, Asia_STD, Malaysia,
Singapore, USA/Canada,
Brazil, Chile, Columbia,
Mexico, Argentina, Peru,
Germany, France, Austria,
Switzerland, Italy, Spain,
Portugal, Norway, Finland,
Sweden, Netherlands,
Denmark, Belgium, Hungary,
Poland, Czech, Romania,
Bulgaria, Ireland
USB Mode
Fast
Use to set the USB speed. Fast is the default
mode. Some PC users may experience poor
USB implementation in the default mode. If this
occurs, select Slow.
Slow
Machine ID
Date & Time
Fax
Use to enter the fax number and name of the
machine.
Name
Enter the current date and time using the
Numeric Keypad. Use Clock Mode to set
whether the machine uses a 12 or 24 hour
clock.
Page 9-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
OPTION
Clock Mode
SETTINGS
12 hour
24 hour
On
DESCRIPTION
The machine can be configured to display time
using either a 12-hour or 24-hour format.
Toner Save
If On, the machine produces a lower quality
output to reduce toner consumption. Useful if
your machine is used for internal documents
only.
Off
Discard Size
[00 - 30]
If the Fax Setup option Auto Reduction is set to
Off, and the received document is as long or
longer than the paper selected, the machine will
discard any excess image from the bottom of
the page that is longer than the selected length.
If the received page is outside the discard
margin set, it will print on two sheets of paper at
the actual size. Margins can be set between 0 -
30mm (1.2").
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-5
Reports
Various Reports are available to assist in confirming and monitoring machine activity. Reports
can be set up to include specific information, or to print automatically.
Reports Available
REPORT
DESCRIPTION
Fax Phonebook
This list contains all the numbers currently stored in the machine’s
fax phonebook as Speed Dial and Group Dial numbers.
Fax TX
This report contains information about recent transmission
activities.
Fax RX
This report contains information about recent reception activities.
System Data
This report shows the status of the user-selectable options. After
settings are changed, print this list to confirm your changes.
Scheduled Jobs
This list identifies the documents currently stored for Delay Send,
Priority Send, Group Dial and TX Poll operations. This list shows
the starting time and type of operation.
Fax TX Confirm
E-mail TX Report
Help List
This list shows a list of confirmed fax transmissions.
This report shows the status of E-mail transmissions.
This list shows the machine’s basic functions and commands to
use as a quick reference guide.
Junk Fax List
This list shows the fax numbers defined as junk fax numbers by
using the Junk Fax Setup menu.
Billing Counters
Connect Page
User Auth List
Print All Reports
This report lists the billing counters and their current amounts.
Provides connection information for the E-mail function.
Provides User Authentication information for the E-mail function.
Use this option to print all the available reports.
Page 9-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Printing Reports
Use the following instructions to print a report.
¾ Press the [Machine Status] key.
1
Enter Machine
Status
¾ Using the Navigation Keys select
2
3
[Reports] and press [Enter].
System Admin Tools
Æ Reports
¾ Using the Navigation Keys select
the required report and press
[Enter].
Reports
[Fax Phonebook]
The report is processed and
printed.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-7
ControlCentre
ControlCentre is software available for the WorkCentre M20i which enables Fax options and
features to be setup and viewed remotely using a PC.
After setting up Fax options or creating phonebooks, simply click [Apply] on the ControlCentre
screen to download the new settings to the machine.
Installing ControlCentre
When Xerox WorkCentre M20i software is installed the ControlCentre utility is installed
automatically.
For information on installing refer to “Maintenance Tools” on page 9-25.
)
Running ControlCentre
Use the following instructions to run ControlCentre:
¾ Start the Windows software.
1
12
¾ From Programs select [Xerox WC M20 Series], then [ControlCentre].
The ControlCentre screen displays.
Page 9-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Using ControlCentre
The ControlCentre software provides five tabs:
Settings
Advanced
-
-
-
-
-
-
-
-
-
Phonebook
Information
Firmware Update
Printer
PCL
Flash Font and Macro
PostScript
To exit ControlCentre, click the [Exit] key in the bottom of each tab screen.
For further details, click the [Help] key in the bottom of each tab screen.
When the settings on ControlCentre are changed, or when ControlCentre is run, the settings on
)
the machine and on ControlCentre will be automatically updated to the latest settings made
either on the machine or on ControlCentre.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-9
Settings Tab
Click on the [Settings] tab to configure Fax settings.
Reads the current
settings in the
WorkCentre M20i then
refreshes
ControlCentre with the
machine’s current
settings.
Downloads the
settings made in
ControlCentre to the
WorkCentre M20i.
Advanced Tab
Click on the [Advanced] tab to change the Machine Setup options applicable to Fax.
Page 9-10
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Phonebook Tab
Click on the [Phonebook] tab to create and edit phonebook entries for use with Fax.
Retrieves the
phonebook
entries from the
Xerox
WorkCentre M20i
to ControlCentre
Phonebook entries
Allows the
phonebook
entries to be
Allows a selected
phonebook entry to
be edited in a
downloaded from
ControlCentre to
the Xerox
separate Edit dialog
box
WorkCentre M20i
Deletes a selected
phonebook entry
Deletes all phonebook
entries
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-11
Information Tab
Click on the [Information] tab to view the software version information and various counters.
The counters show how many scans and prints have been made, and how many jams have
occurred on the machine.
Number of scans
using the
Document Feeder
Number of prints
performed by the
machine
Number of scans
from the
Document Glass
Number of jams in the
Document Feeder
Number of jams
during printing
Number of replaced
toner cartridges
Firmware Update Tab
Click on the [Firmware Update] tab to update the firmware of the machine.
z This feature
should be used
by System
Administrator
only. For further
information,
pleaserefertothe
System
Administration
Guide.
Page 9-12
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Printer Tab
Click on the [Printer] tab to set default print options.
PCL Tab
Click on the [PCL] tab to set options for PCL printing.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-13
Flash Font and Macro Tab
Flash PCL fonts and macros may be supplied on a CD or downloaded from the internet. Use
this tab to install flash PCL fonts and macros on the Xerox WorkCentre M20 or M20i. You can
also delete individual fonts and macros, delete all of the fonts and macros and print a font
listing.
PostScript Tab
Click on the [PostScript] tab to install and manage PostScript fonts on the Xerox WorkCentre
M20 and M20i.
Page 9-14
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Department Codes
Department Codes allow the Administrator to restrict usage and record usage data for
specified departments.
Creating Departments
¾ Press the [Machine Status] key.
1
Enter Machine
Status
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
2
3
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [Department] using the
Navigation Keys and press
[Enter].
System Admin Tools
[Department]
¾ Enter the Master Access Code.
The first time you access
)
Department, you will be
prompted to enter a master
access code then re-enter it to
confirm the code.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-15
¾ Select [Set] using the Navigation
4
Keys and press [Enter].
Department
[Set]
¾ Enter a number to identify the
department and press [Enter].
¾ Enter a name to identify the
department and press [Enter].
¾ Enter the passcode for that
department and press [Enter].
¾ Continue to add departments as
required.
Printing Department Data
This setting is used to print two reports, a Department Code report and a Department Journal.
¾ Press the [Machine Status] key.
1
2
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
Page 9-16
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
¾ Select [Department] using the
Navigation Keys and press
[Enter].
3
4
System Admin Tools
[Department]
¾ Enter the Master Access Code.
The first time that you access
)
Department, you will be
prompted to enter a master
access code then re-enter it to
confirm the code.
¾ Select [Print] using the Navigation
Keys and press [Enter].
Department
[Print]
¾ Select the required report and
press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-17
Managing Departments
This setting is used to enable or disable Department Mode and to clear Department data and
codes.
¾ Press the [Machine Status] key.
1
2
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [Department] using the
Navigation Keys is displayed and
press [Enter].
3
4
System Admin Tools
[Department]
¾ Enter the Master Access Code.
The first time that you access
)
Department, you will be
prompted to enter a master
access code then re-enter it to
confirm the code.
¾ Select [Management] using the
Navigation Keys and press
[Enter].
Department
[Management]
Page 9-18
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
¾ Select [Department Mode] using
the Navigation Keys and press
[Enter].
5
6
Management
[Department Mode]
¾ To enable Department Mode,
select [On] and press [Enter].
¾ Select [Clear Department] using
the Navigation Keys and press
[Enter].
Management
[Clear Department]
¾ To clear the Journal, select
[Journal] and press [Enter].
¾ To remove a Department Code,
select [Code] and press [Enter].
To remove all Department Codes
select [All] and press [Enter].
To remove individual Department
Codes, select [Each], press
[Enter], enter the Department
Number and confirm the removal.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-19
Changing the Master Code
¾ Press the [Machine Status] key.
1
2
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [Department] using the
Navigation Keys and press
[Enter].
3
4
System Admin Tools
[Department]
¾ Enter the Master Access Code.
The first time that you access
)
departments, you will be
prompted to enter a master
access code then re-enter it to
confirm the code.
¾ Select [Change M. Code] and
press [Enter].
Department
[Change M Code]
Page 9-20
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
¾ To change the Master Code,
select [Change] and press
[Enter].
5
Change M Code
[Change]
Enter the new Master Code.
¾ To remove the Master Code,
select [Delete] and press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-21
Passcode Protection
System Administration functions can be restricted to individual users by requiring that a
passcode be entered before access to the functions can be granted.
Enable Passcode Protection
¾ Press the [Machine Status] key.
1
2
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [Passcode Protect] using
the Navigation Keys and press
[Enter].
3
4
Passcode Protect
[Yes]
¾ To enable Passcode Protection,
select [Yes] and press [Enter].
Otherwise select [No] and press
[Enter] to disable Passcode
Protection.
When the machine is first installed, the passcode is blank. When you choose Yes, you will be
asked to enter the passcode. Simply press [Enter] when requested to enter the passcode.
)
to enter the new passcode.
Page 9-22
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Change the Passcode
This procedure is used to change an existing passcode or to enter a passcode after Passcode
Protect has been enabled.
¾ Press the [Machine Status] key.
1
2
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [Change Passcode] using
the Navigation Keys and press
[Enter].
3
4
System Admin Tools
[Change Passcode]
¾ Enter the existing passcode and
press [Enter].
This will be blank if you have just
)
enabled Passcode Protection
¾ Enter the new passcode and
press [Enter].
Enter Passcode:
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-23
Clear Memory
This tool is provided to let you clear the data from selected areas of memory. For Fax, you can
clear the phonebook and both receive and transmit history data; for E-mail, you can clear the
address book and transmit data; and you can clear the system data.
Clearing the Memory
¾ Press the [Machine Status] key.
1
2
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [Clear Memory] using the
Navigation Keys and press
[Enter].
3
Clear Memory
[Fax Phone Book]
¾ Select the option required and
press [Enter].
The choices are:
Fax Phone Book
Fax RX History
Fax TX History
System Data
Email TX History
Email Address Book
Page 9-24
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Maintenance Tools
A number of maintenance tools are provided in System Admin Tools:
Serial Number
Notify Toner Low
-
-
-
-
-
New Drum
Clean Drum
Billing Counters
These tools can also be accessed using Xerox CentreWare, refer to the System Administration
Guide for more information.
)
Check the Serial Number
¾ Press the [Machine Status] key.
1
2
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-25
¾ Select [Maintenance] and press
3
[Enter].
Maintenance
¾ Select [Serial Number] and press
[Serial Number]
[Enter].
The serial number of the Xerox
WorkCentre M20 or M20i is
displayed.
¾ Press [Menu/Exit] to exit this
function.
Page 9-26
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Notify Toner Low
If the Notify Toner option is set to On, when the toner cartridge needs to be replaced, the
machine automatically sends a fax to the service company or the dealer to notify them that the
machine requires a new toner cartridge. This feature will be activated only when the phone
number of the service company or the dealer is stored in the machine’s memory.
¾ Press the [Machine Status] key.
1
2
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [Notify Toner Low] and
3
4
press [Enter].
Maintenance
[Notify Toner Low]
¾ Select [On] and press [Enter].
¾ When prompted, enter:
Notify Toner Low
[On]
Your Customer Number
Your Customer Name
The Supplier’s Fax Number
The Suppliers Name
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-27
New Drum
This function is used to reset the drum counter after the drum has been replaced.
¾ Press the [Machine Status] key.
1
2
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [New Drum] and press
3
[Enter].
New Drum
[On]
¾ To set the drum counter to zero,
select [On] and press [Enter].
Otherwise, select [Off] and press
[Enter] to exit the selection.
Page 9-28
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Clean Drum
If streaks or spots appear on the prints, the drum cartridge may require cleaning. Ensure that
paper is loaded prior to selecting this option.
¾ Press the [Machine Status]
1
2
button.
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [Clean Drum] and press
3
[Enter].
System Admin Tools
[Clean Drum]
The Xerox WorkCentre M20 or
M20i will print a special cleaning
page.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-29
Billing Counters
Billing can display the contents of a number of counters used in the WorkCentre M20i. These
counters are:
-
-
-
-
-
-
-
Total Impressions - the total number of prints produced by the machine.
Toner Impressions - the number of prints produced by the toner.
Drum Impressions - the number of prints produced by the drum.
DADF Scan Page - the number of originals scanned from the Document Feeder.
Platen Scan Page - the number of originals scanned from the Document Glass.
Replaced Toner - the number of prints since the toner was last replaced.
Replaced Drum - the number of prints since the drum was last replaced.
¾ Press the [Machine Status] key.
1
2
¾ Using the Navigation Keys select
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [Billing] and press [Enter].
3
¾ Select the required Counter and
System Admin Tools
[Billing]
press [Enter].
Page 9-30
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Enabling or Disabling Auxiliary Access
Auxiliary Access allows a foreign interface board to be recognized. Use these instructions to
enable or disable Auxiliary Access:
¾ Press the [Machine Status] key.
1
Enter Machine
Status
¾ Using the Navigation Keys select
2
[System Admin Tools] and press
[Enter].
System Admin Tools
[Passcode Protect]
¾ If the System Admin Tools have
already been passcode
protected, type in the password
and press [Enter].
¾ Select [Auxiliary Access] and
3
press [Enter].
System Admin Tools
[Auxiliary Access]
¾ To enable Auxiliary Access,
select [On] is displayed and press
[Enter]. Otherwise, select [Off]
and press [Enter].
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 9-31
Page 9-32
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Cleaning
Cleaning the Document Glass and Constant Velocity Transport
(CVT) Glass
Keeping the Document Glass clean helps ensure the best possible output. It is recommended
that the Document Glass is cleaned at the start of each day and during the day as needed.
The Constant Velocity Transport (CVT) glass is the strip of glass located to the left of the
Document Glass and is used to scan originals fed through the Document Feeder. The CVT
glass also requires cleaning.
CAUTION: DO NOT use organic or strong chemical solvents or aerosol cleaners or
pour fluids directly onto any area. Use supplies and cleaning materials only as
directed in this documentation. Keep all cleaning materials out of the reach of
children.
WARNING: DO NOT remove the covers or guards that are fastened with screws or
attempt any maintenance procedure that is not specifically described in this
documentation.
¾ Slightly dampen a soft lint-free
cloth or paper towel with water.
¾ Open the Document Feeder.
CVT Glass
¾ Wipe the surface of the
Document Glass and CVT Glass
until they are clean and dry.
¾ Wipe the underside of the
Document Feeder until it is clean
and dry.
¾ Close the Document Feeder.
Page 10-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Control Panel and LCD
Regular cleaning keeps the Control Panel and LCD free from dust and dirt. To remove finger
prints and smudges, clean the Control Panel and LCD screen with a soft, lint-free cloth, lightly
dampened with water.
Outside Areas of the Machine
Use a cloth moistened with water to clean the outside areas of the machine.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 10-3
Ordering Supplies
The Toner Cartridge and the Drum Cartridge are available as customer replaceable units.
The customer replaceable unit part numbers are listed below:
CUSTOMER
PART NUMBER
REPLACEABLE UNIT
Europe
USA and Canada
Toner Cartridge
Drum Cartridge
106R01048
106R01047
113R00671
To obtain supplies, contact your local Xerox representative, giving the company name, the
product number and the machine serial number.
Use the space below to keep a record of the telephone number.
Supplies Telephone Number:
# ____________________________________________
Page 10-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Customer Replaceable Units
Toner Cartridge
Expected Cartridge Life
The life of the toner cartridge depends on the amount of toner used in each printed job. For
instance, when printing a typical business letter with about 5% page coverage, expect a toner
cartridge life of approximately 8,000 pages (4,000 pages only for the toner cartridge shipped
with the machine). The actual number may vary according to the print density of the pages
being printed. If printing a lot of graphics the cartridge may require changing more often.
Toner Save Mode
The life of the toner cartridge can be extended by using Toner Save mode. The Toner Save
mode uses less toner than normal printing. The printed image is much lighter, and is adequate
for printing drafts or proofs.
)
Replacing the Toner Cartridge
When the toner cartridge is near the end of its life, white streaks or hue change will occur. The
LCD displays a warning message ‘Toner Low’.
When the ‘Toner Low’ message appears, remove the toner cartridge and gently shake it to
temporarily re-establish the print quality. Shaking the cartridge re-distributes the remaining
toner in the cartridge. This procedure can only be performed once prior to changing the Toner
Cartridge.
¾ Pull the release latch to open the
side cover.
1
CAUTION: Ensure the side cover
is always open before opening
the front cover.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 10-5
¾ Open the front cover.
2
¾ Turn the cartridge locking lever
upwards to release the toner
cartridge.
3
4
z If the
toner gets on
To Re-distribute the Toner:
clothing, wipe it
off with a dry cloth
andwashclothing
in cold water. Hot
water sets toner
into fabric.
¾ Pull out the toner cartridge and
gently shake the cartridge to
distribute the toner evenly inside
the cartridge.
¾ Reinstall the toner cartridge, then
lock the lever.
¾ Close the front cover and the side
cover.
¾ The display shows [New Toner?],
select [No] and press [Enter].
The machine returns to standby.
Page 10-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Replacing the Toner
Cartridge:
5
¾ Shake the new toner cartridge
horizontally four or five times.
¾ Slide the new toner cartridge in
until it locks in place.
¾ Turn the toner locking lever
downwards until it locks in place.
¾ Close the front cover and the side
cover.
¾ The display shows [New Toner?],
select [Yes] and press [Enter].
The machine returns to standby.
Setting the Product to Send Toner Low Information
If the Notify Toner menu option is set to On, when the toner cartridge needs to be replaced,
the machine automatically sends a fax to the service company or the dealer to notify them that
the machine requires a new toner cartridge. This feature will be activated only when the phone
number of the service company or the dealer is stored in the machine’s memory.
on page 9-25.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 10-7
Drum Cartridge
The Drum Cartridge requires replacement when the drum life warning is displayed, after
approximately 18,000 copies.
If streaks or spots are being experienced on the prints there is an option for cleaning the
drum.
)
CAUTION: Do not expose the green drum to light for an extended period. Never
expose the drum to direct sunlight or touch the drum surface. Damage or poor image
quality may result.
Replacing the Drum Cartridge
The useful life of the drum cartridge is approximately 20,000 copies/prints. A high rate of 2
Sided copying/printing reduces the overall life of a drum. The machine displays ‘Drum
Warning’ when the drum is near the end of life. Approximately 1,000 more copies/prints can
be made, but a replacement cartridge should be available. Replace the drum cartridge when
copy/print quality becomes degraded.
¾ Pull the release latch to open the
side cover.
1
2
CAUTION: Ensure the side cover
is always open before opening
the front cover.
¾ Open the front cover.
Page 10-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
3
z The toner
cartridge must be
removed to
¾ Turn the cartridge locking lever
upwards to release the toner
cartridge.
replace the drum
cartridge.
¾ Pull out the used drum cartridge.
4
5
¾ Unpack the new drum cartridge
and slide it in place, making sure
not to touch the surface of the
drum.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 10-9
¾ Reinstall the toner cartridge, then
lock the lever.
6
¾ Close the front cover and the side
cover.
¾ The display shows [New Drum
Unit?]. Select [Yes] and press
[Enter].
The machine returns to Standby
mode.
If the counter is not reset, ‘Drum Warning’ may appear before the new drum reaches its
)
maximum life. To reset the counter manually refer to the “Maintenance Tools” on page 9-25.
Page 10-10
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
General
A variety of situations can affect the quality of the output. For optimal performance, ensure the
following guidelines are followed:
¾ Do not position the machine in direct sunlight or near a heat source such as a radiator.
¾ Avoid sudden changes in the environment surrounding the machine. When a change
occurs, allow the machine at least two hours to adjust to its new environment, depending
on the extent of the change.
¾ Follow routine maintenance schedules for cleaning areas such as the Document Glass
and Control Panel.
¾ Always set the guides in the Paper Trays to the size of the media in the tray.
¾ Ensure paper clips and paper debris do not contaminate the machine.
Page 11-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Fault Clearance
When a fault occurs, check the Status Map on the Control Panel. A red flashing LED identifies
the problem area:-
Status Map
Document
Jams
Bypass
Paper
Jam
Tray 1
Tray 2
Document Jams
If a document jams while it is feeding through the Document Feeder, ‘Document Jam’ appears
on the display and the Document Jam LED on the Status Map will flash.
Details for clearing the three areas of the Document Feeder are given below.
Input Misfeed
¾ Open the Document Feeder top
cover.
1
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 11-3
¾ Pull the document gently to the
right and out of the Document
Feeder.
2
¾ Close the Document Feeder top
cover.
¾ Feed the documents back into
the Document Feeder.
Exit Misfeed
¾ Open the Document Feeder and
turn the roller knob to remove the
misfed documents from the exit
area.
1
2
If the jammed document
cannot be easily removed,
skip to Roller Misfeed.
¾ Close the Document Feeder and
reload the documents.
Page 11-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Roller Misfeed
¾ Open the Document Feeder.
1
2
¾ Turn the release knob to enable
easy removal of the misfed
document from the exit area.
Carefully pull the document to the
right using both hands.
¾ Close the Document Feeder and
reload the documents.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 11-5
Paper Jams
If paper jams occur, ‘Paper Jam’ appears on the display and the Paper Jam or Paper Tray LED
on the Status Map will flash to indicate the problem area. Follow the steps below to clear the
jam. To avoid tearing paper, pull the jammed paper out gently and slowly.
Paper Feed Area
If the paper jams in the feed area ’Paper Jam 0’ appears on the display.
¾ Pull out the Paper Tray.
1
¾ When the tray is fully out, lift the
front part of the tray slightly to
release the tray from the
machine.
¾ Remove the jammed paper by
gently pulling it straight out.
2
¾ Once you remove the jammed
paper, open the side cover and
close it to clear the ’Paper Jam 0’
message from the display.
¾ If there is any resistance and the
paper does not move immediately
when pulled, pull the release
lever to open the side cover.
3
¾ Carefully remove the misfed
paper in the direction shown.
Page 11-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
¾ Close the cover.
4
¾ Insert the paper tray. Lower the
rear part of the tray to align the
rear edge with the corresponding
slot in the machine, then insert it
completely.
Paper Exit Area
If the paper is jammed in the exit area, ’Paper Jam 2’ appears on the display.
¾ Press the Release Lever to open
the side cover.
1
CAUTION: Ensure the side cover
is always open before opening
the front cover.
¾ Open the front cover.
¾ Pull down on the Fuser Lever.
This will release pressure on the
paper.
2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 11-7
¾ Turn the Jam Remove Lever in
the direction of the arrow to move
the paper to the exit area.
3
4
5
¾ Gently pull the paper out through
the exit area.
¾ Push the Fuser Lever up.
¾ Turn the Jam Remove Lever
back to the original position.
¾ Close the front cover and side
cover.
Page 11-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
2 Sided Jam
If a paper jam occurs in the 2 Sided module, ’Duplex Jam’ appears on the display and the
Paper Jam LED on the Status Map will flash.
¾ Press the Release Lever to open
the side cover.
1
¾ Remove the jammed paper.
¾ Close the side cover.
2
Bypass Tray Jam
If you try to print using the Bypass Tray and the machine does not detect paper due to no paper
or improper paper loading, ’Bypass Jam’ appears on the display and the Bypass Tray LED on
the Status Map will flash.
’Bypass Jam’ may also occur when the paper has not fed correctly in the machine.
¾ Open the Bypass Tray and pull
the paper out of the machine.
1
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 11-9
Customer Support
If a fault cannot be resolved by following the LCD instructions, check the troubleshooting
tables in the next section - they may help to solve the problem quickly.
If you need further assistance or information, please visit the Xerox website for online
solutions and support:
http://www.xerox.com
If the problem persists, contact the Xerox Welcome Center or your local Xerox representative.
The serial number of the machine will be required, together with any relevant error codes.
For information on locating the serial number, please refer to “Customer Support” on page 1-5.
)
# ____________________________________________
To access the serial number open the side cover using the release latch and then open the
front door. The serial number is located on the panel above the Toner Cartridge.
The Xerox Welcome Center or local representative telephone number is provided when the
machine is installed. For convenience and future reference, please record the telephone
number in the space below:
Xerox Welcome Center or local representative telephone number:
# ____________________________________________
Xerox US Welcome Center:1-800-821-2797
Xerox Canada Welcome Center:1-800-93-XEROX (1-800-939-3769)
Page 11-10
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
LCD Error Messages
If an abnormal condition arises in the machine or an incorrect operation is performed, a
message indicating the nature of the error is displayed. If this happens, take the corrective
action listed in the following table.
DISPLAY
Bypass Jam
MEANING
SOLUTION
The machine detects non Open the side cover and remove any jammed
feeding from the bypass paper.
tray.
Load paper in the bypass tray.
Comm. Err
The machine has a
problem in
Try resending the fax.
communication.
Document Jam
Feeder.
Door Open
The side cover is not
securely latched.
Close the side cover until it locks into place.
Drum Warning
The drum cartridge is
near the end of life.
Ensure a replacement cartridge is in stock.
Replace the Drum cartridge when copy/print
quality is degraded. This may show up as dark
marks on the edge of the page. Refer to “Drum
Duplex Jam
Drum Empty
The drum cartridge is
empty
Replace the drum cartridge. Refer to “Drum
Fuser Error, Open Heat There is a problem in the Unplug the power cord and plug it back in. If the
Error, Heating Error and
Overheat
fuser unit.
problem still persists, please call for service.
Group Not Available
You have tried to select a Try again. Check location for a group.
group.
Incompatible
Remote party did not
have the requested
feature such as polling.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 11-11
DISPLAY
MEANING
SOLUTION
Non-Xerox Toner Cart
You have used an
unauthorized toner
cartridge.
You must use a Xerox approved cartridge.
Operation Not Assigned The machine has no job
to handle.
Line Busy
Line Error
The remote fax did not
answer.
Try again. Contact recipient to ensure remote
machine is functioning correctly.
Your machine cannot
Try again. If the problem persists, wait an hour
connect with the remote or so for the line to clear, then try again.
machine, or has lost
Or, turn the ECM mode on. Refer to “Fax Setup
contact because of a
Options” on page 6-19 for more information.
problem with the phone
line.
LSU Error
Unit).
problem still persists, please call for service.
Memory Full
The memory is full
Either delete unnecessary documents,
retransmit after more memory becomes
available, or split the transmission into more
than one operation.
No Answer
The remote fax machine Try again. Contact recipient to ensure remote
has not answered after
several redial attempts.
machine is functioning correctly.
Poll Code Err.
Polling Error
You have used an
incorrect poll code.
The remote fax machine The remote operator should know in advance
you want to poll is not that you are polling and have the fax machine
ready to respond to your loaded with the original document.
poll.
Enter the correct poll code.
Or, when setting up to poll
another fax machine, you
have used an incorrect
poll code.
Page 11-12
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
DISPLAY
MEANING
SOLUTION
No. Not Assigned
The speed dial location
has no number assigned.
No Paper
The recording paper in
the paper tray has run
out.
Load the recording paper in the paper tray.
Remove paper.
RX Tray Full
Paper Jam 0
Paper Jam 1
Paper Jam 2
Power Failure
Toner Empty
Paper is overstacked in
the output bin.
paper exit area.
The machine’s memory
has not been backed up.
The toner cartridge has
run out. The machine
stops.
Replace with a new toner cartridge. Refer to
Toner Low
The toner is almost
empty.
Take out the toner cartridge and gently shake it.
By doing this printing operations can be
temporarily resumed.
Retry Redial?
Function Full
The machine is waiting for Press [Start] to immediately redial, or [Stop] to
the programmed interval cancel the redial operation.
to automatically redial.
The memory has become Either delete unnecessary documents, or
full.
retransmit after more memory becomes
available. The transmission can also be split
into more than one operation if it is a large job.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 11-13
Problem and Solutions Charts
The following chart lists some conditions that may occur and the recommended solutions.
Follow the suggested solutions until the problem is corrected. If the problem persists, please
call for service.
Copying Problems
CONDITION
The LCD does not turn on
SUGGESTED SOLUTION
Check that the product is plugged into an electrical receptacle and
ensure that there is power to the receptacle.
Ensure the ON/OFF switch is in the ON position.
Copies are too light or too dark If the original is light, use the Lighten/Darken key to darken the
image.
If the original is dark, use the Lighten/Darken key to lighten the
image.
Smears, lines, marks, or spots
on copies
If defects are on the original, press the Lighten/Darken key to
adjust the image.
If no defects are on the original, clean the Document Glass and
underside of the Document Feeder.
If a line is present when using the Document Feeder and not when
using the Document Glass, clean the CVT glass. For stubborn
spots use a crumpled up piece of paper or a credit card. Refer to
If the problem still persists, clean the Drum Cartridge. Refer to
“Maintenance Tools” on page 9-25 for instructions.
Copy image is skewed
Ensure that original is positioned correctly on the Document
Glass.
Check that copy paper is loaded correctly.
Blank copies
Ensure that the original is face down on the Document Glass or
face up in the Document Feeder.
Image rubs off the copy easily
Replace the paper in the tray with paper from a new package.
In high humidity areas do not leave paper in the product for
extended periods of time.
Page 11-14
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
CONDITION
SUGGESTED SOLUTION
Frequent copy paper jams
Fan the stack of paper, then turn it over in the tray. Replace paper
in paper tray with a fresh supply. Check/adjust paper guides.
Ensure that the paper is the proper paper weight 80 g/m2 (20 lb)
bond paper is recommended.
Check for copy paper or pieces of copy paper remaining in the
product after a paper jam has been cleared.
Toner yield is lower than
expected and TONER LOW
message appears in the LCD
Toner may be lodged in the cartridge. Remove the toner cartridge.
Shake the toner cartridge and tap along the top of the toner
cartridge over a waste receptacle. Take care not to touch the
exposed toner on the left side of the cartridge.
Fewer copies from the Toner
Cartridge than expected
Originals contain pictures, solids, or heavy lines. Originals are
forms, newsletters, books etc. The product is being powered on
and off frequently. The Document Feeder is being left open while
copies are being made.
Printing Problems
PROBLEM
PROBABLE CAUSE
SUGGESTED SOLUTION
Check the cable connection.
The product does not
print
The IEEE-1284 parallel
cable or USB cable is not
connected properly.
The IEEE-1284 parallel
cable or USB cable is
defective.
Check the cable with a computer and printer
that work. If printing is still not possible, replace
the cable.
The port setting is
incorrect.
Check the printer settings in the Windows
Control Panel to ensure that the print job is
being sent to the correct port. (For Example:
LPT1.)
The toner and drum
cartridges are not
installed properly.
Check that the toner and drum cartridges are
installed properly.
The printer driver may not Reinstall the software.
be installed properly.
The parallel port cable
specifications may not be
correct.
Use an IEEE-1284 compliant parallel port cable.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 11-15
PROBLEM
PROBABLE CAUSE
SUGGESTED SOLUTION
Half of the page is blank The page layout is too
Reduce the resolution setting from 600 dpi to
300 dpi. Install more RAM in the computer.
complex.
The page orientation may Change the page orientation in the printer setup
be incorrect.
dialog.
Printing is too slow
The computer parallel
port may not be set for
high speed
If the computer is equipped with an ECP parallel
port, enable this mode of operation. Refer to the
Enabling High Speed Printer Communications
section of the PC’s user guide.
communications.
Computer may not have Install more RAM in the computer.
enough memory (RAM).
Print job is too large
Reduce resolution from 600 dpi to 300 dpi.
Irregular faded patches There is a paper quality
Use only paper that meets the specifications
required by the product.
of print
problem.
Toner may be unevenly
distributed.
Remove the toner cartridge and shake it gently
to distribute the toner evenly. Then reinstall the
toner cartridge.
Black staining
There is a paper quality
problem.
Use only paper that meets the specifications
required by the product.
Character voids
Background scatter
The paper may be too
dry.
Try printing with a different batch of paper.
The paper may be too
damp.
Try printing with a different batch of paper. Do
not open packages of paper until necessary so
that the paper does not absorb too much
moisture from the air.
Printing over uneven
surfaces.
If printing onto envelopes, change the printing
layout to avoid printing over areas that have
overlapping seams on the reverse side.
Missing characters
The paper may be too
damp.
Try printing with a different batch of paper. Do
not open packages of paper until necessary so
that the paper does not absorb too much
moisture from the air.
Back of printout is dirty The transfer roller may be Print a few blank pages to clean the transfer
dirty.
roller.
Incorrect fonts
TrueType fonts may be
disabled.
Use the fonts dialog box in the Control Panel to
enable TrueType fonts.
Page 11-16
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
PROBLEM
PROBABLE CAUSE
SUGGESTED SOLUTION
Faded graphics
Toner may be low.
Remove the toner cartridge and shake it gently
to distribute the toner evenly. Then reinstall the
toner cartridge.
Ensure that a spare toner cartridge is available.
E-mail Problems
PROBLEM
PROBABLE CAUSE
SUGGESTED SOLUTION
Not Assigned
The Group Mail you tried Type the address manually.
to use has no E-mail
assigned to it.
Send Error (SMTP)
Your machine cannot
Try again. If the problem persist, try again once
connect with the server or the network fault is resolved.
has lost contact due to a
network problem.
Recipient Address
Failure
The recipient address
could not be contacted or
is invalid.
Ensure correct address is entered.
Try again.
Connection Failure
Any type of
communication or
network failure during E-
mail operations.
Authentication Failure Invalid Account or
Password
Ensure correct account and password are used.
Authentication
Required
Authentication is disabled Ensure Authentication is enabled. Refer to the
and the mail server
requires it.
System Administrator.
SMTP Server CONN.
Failure
SMTP server connection
failure.
Invalid Server or Port
No.
Wrong SMTP server or
port number.
SMTP DNS CONN.
Failure.
DNS connection failure.
SMTP DNS Domain
Error
Error in the SMTP DNS
Domain.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 11-17
PROBLEM
PROBABLE CAUSE
SUGGESTED SOLUTION
E-mail Associated
Cannot Delete
Displayed when an entry Remove the group mail association before
associated with group
mail is deleted from the
Address book
deleting the entry.
Mail Too Large
Displayed when the
machine is unable to split
the mail and send it. For
example, if the mail size is
configured to 1.0MB and
a single page is larger
than 1.0MB
Empty Address Book
Displayed when an
attempt is made to
retrieve an address from
an empty Address book.
Address Book Full
Group Empty
Displayed when Address
book is full with the
maximum entries.
Displayed when attempt
is made to delete an entry
from an empty Group.
Group is Full
Displayed when an
attempt is made to add an
entry to a Group that is full
with maximum entries.
Entry Already Exists
Invalid Email ID
Enter Again
Displayed when entering
an entry which already
exists in the Address
book.
Displayed when the E-
mail ID is invalid
Ensure the E-mail address does not have any
spaces in between and that it does not start with
special characters such as + or @ and that the
ID only contains one @ symbol.
Displayed when an
attempt is made to enter
an invalid Group number.
Page 11-18
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
PROBLEM
PROBABLE CAUSE
SUGGESTED SOLUTION
Configured Already
Displayed when an
attempt is made to
configure and already
configured Group.
Invalid Login
Displayed when Login
and/or password are
invalid or do not
Ensure the login information and password are
valid and entered accurately.
correspond.
Faxing Problems Solution Chart
PROBLEM
SUGGESTED SOLUTION
Originals are fed diagonally
(skewed)
Ensure the Document Guides are adjusted to the width of the
original being fed.
Check the original meets the conditions established for use with
this device.
The original is not being printed Ensure the originals were placed face-up in the Document Feeder
on the paper of the remote Fax
even though it is being sent
or face-down on the Document Glass.
Originals are not sent even if
operations are carried out
normally
Check that the remote Fax is compatible with the machine. This
machine supports G3 communications but not G4
communications.
Originals cannot be received
even if [Start] is pressed
Ensure the bell rings before picking up the handset.
Ensure the handset is not replaced before pressing [Start]. When
answering a call using the handset and a Fax is being received, do
not replace the handset until [Start] is pressed and the phone line
switches to the machine.
Check the telephone cord has not been disconnected.
Check the power plug has not been unplugged from the power
outlet.
Check with the party trying to send the original that there are no
problems with the remote fax.
Paper is not collated
Ensure the machine has paper loaded.
Check if a paper jam has occurred.
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 11-19
PROBLEM
SUGGESTED SOLUTION
The received original is printed Check with the party sending the original that the original is a
dark and is illegible or black
stripes are printed on the
original
clean copy.
Check with the party sending the original that the problem is not
due to a fault or operator error at the remote Fax. For example,
dirty scan glass or dirty scan lamp.
If the same problem occurs even when copies are made on the
machine, clean the drum. Refer to “Maintenance Tools” on page 9-
25 for instructions.
Paper is collated but not printed. Ensure there enough toner.
Check with the party sending the fax that the original was placed
correctly when scanned at the remote Fax.
Page 11-20
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Introduction
The Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i adhere to strict
specifications, approvals and certifications. These specifications are designed to provide for
the safety of users and to ensure that the machine operates in a fully functional state. Use the
specifications listed in this chapter to quickly identify the capabilities of the machine.
z If further
specification
information is
required please
refer to
www.xerox.com.
Page 12-2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Printer Specifications
ITEM
DESCRIPTION
Emulation
PCL6
Resolution
True 600 x 600 dpi, 1200 dpi class
21 ppm for A4 / 22 ppm for Letter
Printing speed
Effective printing width
208 mm (8.2 inches) for letter / legal (216 x 356 mm / 8.5 x 14 inch)
202 mm (8 inches) for A4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 12-3
Fax Specifications
ITEM
DESCRIPTION
Applicable line
G3 PSTN (Public Switched Telephone Network)
ITU G3, Super G3
Communication Standard
Resolutions
Standard
203 x 98 dpi
203 x 196 dpi
300 x 300 dpi
203 x 392 dpi
406 x 394 dpi
Fine
Super Fine (Fine Photo)
Super Fine
Super Fine
Halftone (Error Diffusion)
Receiving Resolutions
Data coding
203 x 98 dpi, 203 x 196 dpi, 300 x 300 dpi, 203 x 392 dpi, 406 x 394 dpi
MH/MR/MMR/JBIG/JPEG (Color Transmission)
33.6 kbps
Maximum modem speed
Transmission speed
Fax Memory
<3 seconds (Standard resolution, MMR, 33.6 kbps)
16 MB
Printing speed
21 ppm (for A4) 22 ppm (letter size)
208 mm (8.2 inches)
Effective scanning width
Effective printing width
208 mm (8.2 inches) for letter / legal (216 x 356 mm / 8.5 x 14)
202 mm (8 inches) for A4
Document width and weight
Document Feeder:
176 ~ 216 mm (7 ~ 8.5 inches)
2
45 ~ 105 g/m (12.5 ~ 28 lb)
Platen:
Maximum Legal (216 x 356 mm / 8.5 x 14 inch)
2
Input paper tray capacity
Document Feeder
Tray 1 and Tray 2 (optional):
Bypass Tray:
550 sheets 80 g/m (20 lb)
2
100 sheets 80 g/m (20 lb)
2
Document Feeder:
Platen:
Up to 50 pages 80 g/m (20 lb)
1 page
Page 12-4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Scanner and Copier Specifications
ITEM
Scanning method
Copy speed
DESCRIPTION
CCD, Flat-bed
21 A4 / 22 Letter Copies Per Minute
2.5 msec/line MONO
Scan speed
Scan resolution
600 x 600 dpi, 1200 dpi class
True Color, 250 Gray, Black and white
Black and White
Scan mode
Copy mode
Effective scanning width
Maximum document width
Multi copy range
Reduction & Enlargement
208 mm (8.2 inches)
216 mm (8.5 inches)
1 ~ 999
25% ~ 400% in 1% increments (from Platen)
25% ~ 100% in 1% increments (from Document Feeder)
Top, Bottom, Each side 4 mm (0.16 inch)
Under 8 seconds (Normal - Ready)
33 seconds (from Power Saver)
Maximum print edge margin
First Copy Out Time
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 12-5
General Specifications
ITEM
DESCRIPTION
2
Input paper tray capacity
Tray 1 and Tray 2 (optional):
550 sheets 80 g/m (20 lb)
2
Bypass Tray:
100 sheets 80 g/m (20 lb)
2
Output tray capacity
250 sheets 80 g/m (20 lb), face down
Toner cartridge life
Drum life
8,000 pages (for Starter Cartridge 4,000 pages) at 5% coverage
20,000 pages (5% coverage)
Operating Environment
Temperature: 10 - 32° C / 50 - 90° F (20 ~ 80% RH)
Paper size and weight
Trays 1 & 2:
Bypass tray:
Duplex:
A4, Letter, Folio, Legal (216 x 356 mm / 8.5 x 14 inch
2
60 ~ 90 g/m (16 ~ 24 lb)
A6 ~ Legal (216 x 356 mm / 8.5 x 14 mm)
2
60 ~ 160 g/m (16 ~ 43 lb)
A4, Letter, Folio, Legal (216 x 356 mm / 8.5 x 14 inch)
2
80 ~ 90 g/m (20 ~ 24 lb)
Original document width and
weight
Document Feeder:
176 ~ 216 mm (7 ~ 8.5 inches)
2
45 ~ 105 g/m (12.5 lb ~ 28 lb)
Platen:
Maximum legal (216 x 356 mm / 8.5 x 14 inch)
2
Document Feeder capacity
Power rating
50 sheets 80 g/m (20 lb)
AC220 ~ 240V (Europe), 50/60 Hz 3.0A
AC110 ~ 127V (US, Canada), 50/60 Hz 6.0A
35 W in Power save mode
Power consumption
115 W in Standby mode
430 W / 420 W during operation
Weight
32 kg (Drum and Toner Cartridges included)
540 x 441 x 488 mm (21 x 17 x 19 inches) without Tray 2
540 x 441 x 619 mm (21 x 17 x 24.4 inches) with Tray 2
C20 = 32MB, M20 = 32MB, M20i = 80MB
Dimensions (WxDxH)
Memory Size
Page 12-6
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Media Specifications
ITEM
DESCRIPTION
Plain paper, OHP film, Label, Envelope, Card, Postcard
Paper types
available
Paper Type
W x L (mm)
215.9 x 279
W x L (Inch)
8.5 x 11
Letter
Legal
JIS B5
A4
215.9 x 355.6
182 x 257
8.5 X 14
7.17 x 10.12
8.27 x 11.69
7.25 x 10.5
5.85 x 8.27
4.13 x 5.85
4 x 6
210x 297
Executive
A5
184.2 x 266.7
148.5 x 210
105 x 148.5
101.6 x 152.4
100 x 148
Paper Sizes
A6 card
Post Card 4x6
HagaKi
3.94 x 5.83
3.88 x 7.5
4.12 x 9.5
4.33 x 8.66
6.38 x 9.02
Envelope 7-3/4
Envelope COM-10
Envelope DL
Envelope C5
Custom
98.4 x 190.5
105 x 241
110 x 220
162 x 229
98 x 148 ~
215.9 x 355.6
3.86 x 5.83 ~
8.5 x 14
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page 12-7
ITEM
DESCRIPTION
Input Source
Source
Media Types
Sizes
Thickness
2
Paper Tray
Plain Paper
A4, Letter, Legal,
Folio
60 ~ 90 g/m
(16lb ~ 24lb)
2
Bypass Tray
Plain Paper,
Envelope,
Transparency,
A4, Letter, Legal,
Folio, Executive, A5,
B5, A6, Monarch (7
60 ~ 160 g/m
(16lb ~ 43lb)
Label, Cardstock 3/4), COM10, #9,
C5, DL, Custom
2
Duplex
Plain Paper
A4, Letter, Folio,
Legal
80 ~ 90 g/m
(20lb ~ 24lb)
L
B5 means JIS and ISO
Transparency film thickness: 150 µm
Paper Label thickness: 140 µm
Page 12-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Index
Numerics
C
2 Sided
Calling for Service 1-5
Changing the Master Code 9-20
Clean Drum 9-29
Cleaning
copy 3-7
E-mail 5-7
fax 6-8
Control Panel and LCD Display 10-3
Outside Areas 10-3
Clear Memory 9-24
Clone
copy 3-7
Collated
A
About this guide 1-3
Adding Paper 2-15
Administration Tools
Clear Memory 9-24
Department Codes 9-15
Maintenance Tools 9-25
Passcode Protection 9-22
Advanced Tab 9-10
Auto Fit
copy 3-8
Color Original
copy 3-8
E-mail 5-7
Component Location 2-5
Connections 2-12
Control Panel Overview 2-7
ControlCentre 9-8
Advanced Tab 9-10
Firmware Update Tab 9-12
Information Tab 9-12
Installing 9-8
Phonebook Tab 9-11
Running ControlCentre 9-8
Settings Tab 9-10
Using ControlCentre 9-9
Conventions 1-3
Copier Problems Solution Chart 11-14
Copy 3-6
copy 3-7
Auto Suppress
copy 3-12
B
Basic Troubleshooting
Copier Problems Solution Chart 11-14
Faxing Problems Solution Chart 11-19
LCD Error Messages 11-11
Printing Problems Solution Chart 11-15
Solving Problems 11-14
Batch TX 6-13
Billing Counters 9-30
Book Copy
1-2 Sided 3-7
Auto Fit 3-7
Auto Suppress 3-12
Book Copy 3-12
copy 3-12
Bypass Tray 4-5
Clone 3-7
collated 3-8
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page Index - 1
Color Original 3-8
Covers 3-12
Drum Cartridge, installing 2-10
Drum Cleaning 9-29
Create Booklet 3-13
Edge Erase 3-11
ID Card Copy 3-10
Lighten/Darken 3-6
Margin Shift 3-11
Drum Replacement 9-28
E
Edge Erase
copy 3-11
N Up 3-13
Original Type 3-8
Paper Supply 3-9
Reduce/Enlarge 3-6
2 Sided 5-7
color original 5-7
Original Type 5-7
E-mail key 5-3
Transparencies 3-13
Copy Feature selection 3-4
Copy Features 3-6
Copying Procedure 3-2
Counters Information 9-12
Covers
E-mail, File Type 5-6
E-mail, Mail Subject 5-6
E-mail, Multiple Recipients 5-5
E-mail, Recipients name 5-4
E-mail, Send to Myself 5-5
E-mail, Sender’s Name 5-4
E-mail, sending an e-mail 5-2
E-mail, Start 5-6
copy 3-12
Create Booklet
Energy Star 1-18
Enter the Fax Number 6-4
Error Messages 11-11
Expected Toner Cartridge Life 10-5
External Connections 2-12
copy 3-13
Creating Departments 9-15
Customer Replaceable Units 10-5
Drum Cartridge 10-8
Toner Cartridge 10-5
Customer Support 1-5
F
Fault Clearance 11-3
Fax 6-9
D
Delay Fax 6-11
2 Sided 6-8
Department Codes 9-15
Changing the Master Code 9-20
Creating Departments 9-15
Managing Departments 9-18
Printing Department Data 9-16
Dialing Methods
Lighten/Darken 6-8
Original Type 6-9
start 6-5
Fax Features 6-8
Fax Number 6-4
Fax Setup Options 6-19
Fax Specification 12-4
Faxing Problems Solution Chart 11-19
Faxing Procedure 6-2
Features
Keypad Dialing 6-6
Manual Dialing 6-7
Manual Group Dialing 6-7
Redial 6-7
Drum Cartridge 10-8
Fax 6-8
File Type 5-6
Firmware Update Tab 9-12
Replacing the Drum Cartridge 10-8
Page Index - 2
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Workstation Setup 2-26
Location of Components 2-5
G
General Problems 11-2
General Specification 12-6
Getting Started
M
Machine Overview 2-4
Machine Setup 2-19
ControlCentre 9-8
Setup Overview 9-2
Mail Subject 5-6
Copying Procedure 3-2
Loading Paper 4-2
Scanning Procedure 8-3
Group Mail 5-9
I
Mailbox 6-14
ID Card Copy
Maintenance Tools
Billing Counters 9-30
Check Serial Number 9-25
Clean Drum 9-29
copy 3-10
Information Sources 1-4
Information Tab 9-12
Installing ControlCentre 9-8
Installing Drum and Toner Cartridges 2-10
Installing Software 2-23
Interrupt Job Features 3-15
Introduction 1-2
New Drum 9-28
Notify Toner Low 9-27
Making Connections 2-12
Managing Departments 9-18
Manual Dialing 6-7
Manual Group Dialing 6-7
Margin Shift
J
Job Status 6-5
copy 3-11
Memory Fax 6-11
K
Keypad Dialing 6-6
Meter Readings 9-12
Models and Options 2-4
Multiple recipients 5-5
L
Laser Safety 1-10
LCD Error Messages 11-11
Lighten/Darken
N
N Up
copy 3-6
copy 3-13
fax 6-8
O
Options 2-4
Bypass Tray 4-5
Paper Tray 4-2
Ordering Supplies 10-4
Original Type
copy 3-8
Preparation 4-2
E-mail 5-7
Stock Types 4-9
Local Connection
Driver Installation 2-24
Test Print 2-28
fax 6-9
Overview Control Panel 2-7
P
Test Scan 2-28
Paper Specification 12-7
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page Index - 3
Paper Supply
Regulatory Information 1-9
Related Information Sources 1-4
Replacing the Drum Cartridge 10-8
Bypass Tray 4-5
copy 3-9
Loading Paper 4-2
Paper Tray 4-2
E-mail 5-8
Preparation 4-2
Fax 6-9
Stock Types 4-9
Paper Supply selection 3-2
Paper Tray 4-2
Paper, loading 2-15
Change the Passcode 9-23
Enable 9-22
Resume Current Job 3-16
Running ControlCentre 9-8
S
Safety 1-6
Safety Standards 1-8
Scan 8-3
Phonebook Tab 9-11
Polling 6-12
Power Off 2-14
Power On 2-14
Preparing paper for loading 4-2
Print 7-2
Scanner and Copier Specification 12-5
Scanning Procedure 8-3
Selecting Copy Features 3-4
Selecting Interrupt 3-14
Selecting the E-mail Features 5-3
Selecting the Paper Supply 3-2
Send to Myself 5-5
Sender’s Name 5-4
Sending a Fax 6-2
Sending an E-mail 5-2
Serial Number 9-25
Serial number 1-5
Setting the Product to Send Toner Low Information
ControlCentre 9-8
Installing ControlCentre 5.0 9-8
Settings Tab 9-10
Setups
Print Address Book 5-12
Print Count 9-12
Printer Specification 12-3
Printing a Document 7-2
Printing Department Data 9-16
Printing Problems Solution Chart 11-15
Printing Procedure 7-2
Problem Solving 11-14
Problems
Fault Clearance 11-3
General 11-2
Q
R
Overview 9-2
Software Installation 2-23
Solutions, Copier Problems 11-14
Solutions, Faxing Problems 11-19
Solutions, Printing Problems 11-15
Solving Problems 11-14
Specifications
Recipients Name 5-4
Redial 6-7
Reduce/Enlarge
copy 3-6
Regulations - Canada 1-17
Regulations - Europe 1-14
Regulations - USA 1-15
Fax 12-4
General 12-6
Paper 12-7
Page Index - 4
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Printer 12-3
Copier Problems Solution Chart 11-14
Fault Clearance 11-3
Faxing Problems Solution Chart 11-19
General Problems 11-2
LCD Error Messages 11-11
Printing Problems Solution Chart 11-15
Solving Problems 11-14
Scanner and Copier 12-5
Specifications, Media 4-9
Status Map
Auto Tray Switching 2-8
Stock Types 4-9
Switching Off 2-14
Switching On 2-14
System Setup
U
Unpacking 2-2
User Interface 2-7
Installing ControlCentre 9-8
Using ControlCentre 9-9
T
Using the Document Feeder 3-3
Using the Document Glass 3-4
Using the Global Address Book 5-13
Toll Save 6-10
Toner Cartridge 10-5
Expected Cartridge Life 10-5
Setting the Product to Send Toner Low Infor-
mation 10-7
W
Toner Save Mode 10-5
Toner Cartridge, installing 2-10
Toner Low Information 10-7
Toner Low Notification 9-27
Toner Save Mode 10-5
Total Number of Prints 9-12
Transparencies
Welcome 1-2
Welcome Center 1-5
X
Xerox Website 1-5
Xerox Welcome Center 1-5
copy 3-13
Troubleshooting
Xerox CopyCentre C20, WorkCentre M20 and WorkCentre M20i User Guide
Page Index - 5
|
Zebra Technologies 11280100000 User Manual
Wtb Float100rlc User Manual
Schumacher 10 Amp User Manual
Samsung Mh026fpea User Manual
Ricoh Fax5600l User Manual
Mpc Atd Actuator 50 Atd 313186 User Manual
LG LG E435 User Manual
LG 60UH6150 02 User Manual
CRAFTSMAN 315.23743 User Manual
ACER ASPIRE R 14 R5 431T User Manual