Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
OperatOr’s Manual
CC 30 H
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-11325
(December 2, 2015)
Important Safe Operation Practices
2
WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
CALIFORNIA PROPOSITION 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and reproductive
harm. Wash hands after handling
DANGER! This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating hands and feet
and throwing objects. Failure to observe the following safety instructions could result in
serious injury or death.
6.
Thoroughly inspect the area where the equipment is to be
used. Remove all stones, sticks, wire, bones, toys, and other
foreign objects which could be picked up and thrown by
the blade(s). Thrown objects can cause serious personal
injury.
General Operation
1.
Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
7.
Plan your mowing pattern to avoid discharge of material
toward roads, sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or obstruction
which may cause discharged material to ricochet back
toward the operator.
2.
3.
Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.
8.
9.
Always wear safety glasses or safety goggles during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
Wear sturdy, rough-soled work shoes and close-fitting
slacks and shirts. Loose fitting clothes and jewelry can be
caught in movable parts. Never operate this machine in
bare feet or sandals.
4.
5.
Never allow adults to operate this machine without proper
instruction.
To help avoid blade contact or a thrown object injury,
keep bystanders, helpers, children and pets at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.
10. Be aware of the mower and attachment discharge direction
and do not point it at anyone. Do not operate the mower
without the discharge cover or entire grass catcher in its
proper place.
11. Do not put hands or feet near rotating parts or under the
cutting deck. Contact with the blade(s) can amputate
hands and feet.
3
12. A missing or damaged discharge cover can cause blade
contact or thrown object injuries.
Slope Operation
Slopes are a major factor related to loss of control and tip-over
accidents which can result in severe injury or death. All slopes
require extra caution. If you cannot back up the slope or if you
feel uneasy on it, do not mow it.
13. Stop the blade(s) when crossing gravel drives, walks, or
roads and while not cutting grass.
14. Watch for traffic when operating near or crossing
roadways. This machine is not intended for use on any
public roadway.
For your safety, use the slope gauge included as part of this
manual to measure slopes before operating this machine on
a sloped or hilly area. If the slope is greater than 12 degrees as
shown on the slope gauge, do not operate this machine on that
area or serious injury could result.
15. Do not operate the machine while under the influence of
alcohol or drugs.
16. Mow only in daylight or good artificial light.
17. Never carry passengers.
Do:
1.
Mow up and down slopes, not across. Exercise extreme
caution when changing direction on slopes.
18. Disengage blade(s) before shifting into reverse. Back up
slowly. Always look down and behind before and while
backing to avoid a back-over accident.
2.
Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.
19. Slow down before turning. Operate the machine smoothly.
Avoid erratic operation and excessive speed.
3.
Use slow speed. Choose a low enough speed setting so
that you will not have to stop or shift while on the slope.
Tires may lose traction on slopes even though the brakes
are functioning properly. Always keep machine in gear
when going down slopes to take advantage of engine
braking action.
20. Disengage blade(s), set parking brake, stop engine and wait
until the blade(s) come to a complete stop before removing
grass catcher, emptying grass, unclogging chute, removing
any grass or debris, or making any adjustments.
21. Never leave a running machine unattended. Always turn
off blade(s), set parking brake, stop engine and remove key
before dismounting.
4.
5.
6.
Follow the manufacturer’s recommendations for wheel
weights or counterweights to improve stability.
22. Use extra care when loading or unloading the machine into
a trailer or truck. This machine should not be driven up or
down ramp(s), because the machine could tip over, causing
serious personal injury. The machine must be pushed
manually on ramp(s) to load or unload properly.
Use extra care with grass catchers or other attachments.
These can change the stability of the machine.
Keep all movement on the slopes slow and gradual. Do
not make sudden changes in speed or direction. Rapid
engagement or braking could cause the front of the
machine to lift and rapidly flip over backwards which could
cause serious injury.
23. Muffler and engine become hot and can cause a burn. Do
not touch.
24. Check overhead clearances carefully before driving under
low hanging tree branches, wires, door openings etc.,
where the operator may be struck or pulled from the
machine, which could result in serious injury.
7.
Avoid starting or stopping on a slope. If tires lose traction,
disengage the blade(s) and proceed slowly straight down
the slope.
25. Disengage all attachment clutches and depress the brake
pedal completely before attempting to start engine.
Do Not:
1.
Do not turn on slopes unless necessary; then, turn slowly
26. Your machine is designed to cut normal residential grass of
a height no more than 10”. Do not attempt to mow through
unusually tall, dry grass (e.g., pasture) or piles of dry leaves.
Dry grass or leaves may contact the engine exhaust and/
or build up on the mower deck presenting a potential fire
hazard.
and gradually downhill, if possible.
2.
Do not mow near drop-offs, ditches or embankments. The
mower could suddenly turn over if a wheel is over the edge
of a cliff, ditch, or if an edge caves in.
3.
Do not try to stabilize the machine by putting your foot on
the ground.
27. Use only accessories and attachments approved for this
machine by the machine manufacturer. Read, understand
and follow all instructions provided with the approved
accessory or attachment.
4.
5.
Do not use a grass catcher on steep slopes.
Do not mow on wet grass. Reduced traction could cause
sliding.
28. Data indicates that operators, age 60 years and above, are
involved in a large percentage of riding mower-related
injuries. These operators should evaluate their ability
to operate the riding mower safely enough to protect
themselves and others from serious injury.
6.
7.
Do not coast downhill. Over-speeding may cause the
operator to lose control of the machine resulting in serious
injury or death.
Do not tow heavy pull behind attachments (e.g. loaded
dump cart, lawn roller, etc.) on slopes greater than 5
degrees. When going down hill, the extra weight tends
to push the tractor and may cause you to loose control
(e.g. tractor may speed up, braking and steering ability are
reduced, attachment may jack-knife and cause tractor to
overturn).
29. If situations occur which are not covered in this manual, use
care and good judgment. Contact your customer service
representative for assistance.
4
Section 2 — important Safe operation practiceS
Children
Service
1.
Tragic accidents can occur if the operator is not alert to the
Safe Handling of Gasoline:
presence of children. Children are often attracted to the
machine and the mowing activity. They do not understand
the dangers. Never assume that children will remain where
you last saw them.
1.
To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely
flammable and the vapors are explosive. Serious
personal injury can occur when gasoline is spilled on
yourself or your clothes which can ignite. Wash your skin
and change clothes immediately.
a. Keep children out of the mowing area and in
watchful care of a responsible adult other than the
operator.
a. Use only an approved gasoline container.
b. Be alert and turn machine off if a child enters the
area.
b. Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
c. Before and while backing, look behind and down for
small children.
d. Never carry children, even with the blade(s) shut off.
They may fall off and be seriously injured or interfere
with safe machine operation.
c. When practical, remove gas-powered equipment
from the truck or trailer and refuel it on the ground.
If this is not possible, then refuel such equipment on
a trailer with a portable container, rather than from a
gasoline dispenser nozzle.
e. Use extreme care when approaching blind corners,
doorways, shrubs, trees or other objects that may
block your vision of a child who may run into the
path of the machine.
d. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
f.
To avoid back-over accidents, always disengage
the cutting blade(s) before shifting into Reverse.
If equipped, the “Reverse Caution Mode” should
not be used when children or others are around.
e. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
f.
Never fuel machine indoors.
g. Keep children away from hot or running engines.
They can suffer burns from a hot muffler.
g. Never remove gas cap or add fuel while the engine
is hot or running. Allow engine to cool at least two
minutes before refueling.
h. Remove key when machine is unattended to
prevent unauthorized operation.
h. Never over fill fuel tank. Fill tank to no more than ½
inch below bottom of filler neck to allow space for
fuel expansion.
2.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.
i.
j.
Replace gasoline cap and tighten securely.
If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
Towing
1.
Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
k. To reduce fire hazards, keep machine free of grass,
leaves, or other debris build-up. Clean up oil or fuel
spillage and remove any fuel soaked debris.
2.
Follow the manufacturers recommendation for weight
limits for towed equipment and towing on slopes.
l.
Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
as on a water heater, space heater, furnace, clothes
dryer or other gas appliances.
3.
4.
Never allow children or others in or on towed equipment.
On slopes, the weight of the towed equipment may cause
loss of traction and loss of control.
m. Allow a machine to cool at least five minutes before
storing.
5.
Always use extra caution when towing with a machine
capable of making tight turns (e.g. “zero-turn” ride-on
mower). Make wide turns to avoid jack-knifing.
General Service
1.
Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless,
and deadly gas.
6.
7.
Travel slowly and allow extra distance to stop.
Do not coast downhill.
2.
Before cleaning, repairing, or inspecting, make certain the
blade(s) and all moving parts have stopped. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
Section 2 — important Safe operation practiceS
5
3.
Periodically check to make sure the blades come to
complete stop within approximately (5) five seconds after
operating the blade disengagement control. If the blades
do not stop within the this time frame, your machine
should be serviced professionally by an authorized MTD
Service Dealer.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
4.
5.
Check brake operation frequently as it is subjected to wear
during normal operation. Adjust and service as required.
Notice Regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM), Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
Check the blade(s) and engine mounting bolts at frequent
intervals for proper tightness. Also, visually inspect blade(s)
for damage (e.g., excessive wear, bent, cracked). Replace
the blade(s) with the original equipment manufacturer’s
(O.E.M.) blade(s) only, listed in this manual. “Use of parts
which do not meet the original equipment specifications
may lead to improper performance and compromise
safety!”
When required, models are equipped with low permeation fuel
lines and fuel tanks for evaporative emission control. California
models may also include a carbon canister. Please contact
Customer Support for information regarding the evaporative
emission control configuration for your model.
6.
7.
Mower blades are sharp. Wrap the blade or wear gloves,
and use extra caution when servicing them.
Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
Spark Arrestor
8.
9.
Never tamper with the safety interlock system or other
safety devices. Check their proper operation regularly.
WARNING! This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered,
brushcovered or grass-covered land unless the
engine’s exhaust system is equipped with a spark
arrestor meeting applicable local or state laws (if
any).
After striking a foreign object, stop the engine, disconnect
the spark plug wire(s) and ground against the engine.
Thoroughly inspect the machine for any damage. Repair
the damage before starting and operating.
10. Never attempt to make adjustments or repairs to the
machine while the engine is running.
If a spark arrestor is used, it should be maintained in effective
working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
A spark arrestor for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
11. Grass catcher components and the discharge cover are
subject to wear and damage which could expose moving
parts or allow objects to be thrown. For safety protection,
frequently check components and replace immediately
with original equipment manufacturer’s (O.E.M.) parts only,
listed in this manual. “Use of parts which do not meet the
original equipment specifications may lead to improper
performance and compromise safety!”
12. Do not change the engine governor settings or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
13. Maintain or replace safety and instruction labels, as
necessary.
14. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
15. According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years,
or 270 hours of operation. At the end of the Average Useful
Life have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety
systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
6
Section 2 — important Safe operation practiceS
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol
Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate.
DANGER— ROTATING BLADES
Never carry passengers. Never carry children, even with the blades OFF.
DANGER— ROTATING BLADES
To avoid a back-over accident, keep children away from the machine while it is in
operation. Mowing in reverse is not recommended.
WARNING— ROTATING BLADES
Do not put hands or feet near rotating parts or under the cutting deck. Contact with
the blade(s) can amputate hands and feet. Be sure blades and engine are stopped
before placing hands or feet near blades.
DANGER— ROTATING BLADES
Always look down and behind before and while backing to avoid a back-over
accident.
DANGER— BYSTANDERS
Keep bystanders, helpers, children and pets at least 75 feet from the machine while it
is in operation.
WARNING— THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious personal
injury.
WARNING—THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious personal
injury.
WARNING— SLOPE OPERATION
Go up and down slopes, not across.
WARNING— SLOPE OPERATION
Use extra caution on slopes. Do not mow slopes greater than 12°. If machine stops
going uphill, stop blades back down slowly.
DANGER— SLOPE OPERATION
Do not operate this machine where it could tip or slip. Avoid sudden turns. Use low
speed.
Section 2 — important Safe operation practiceS
7
Symbol
Description
DANGER— GUARDS, SHEILDS, SWITCHES, ETC.
Keep safety devices (Guards, Sheilds, Switches, Etc.) in place and working.
WARNING— MACHINE IS HOT
Allow the engine to cool at least two minutes before refueling or storing.
WARNING— THIS EQUIPMENT MAY CREATE SPARKS
Operation of this equipment may create sparks that can start fires around dry
vegetation. Do not drive through piles of dry leaves or tall dry grass (Max. 10”). Keep
the machine free of debris.
max10"
WARNING— HOT SURFACE
Engine parts, especially the muffler, become extremely hot during operation. Allow
engine and muffler to cool before touching.
DANGER — ROTATING BLADES
To reduce the risk of injury, keep hands and feet away. Do not operate unless
discharge cover or grass catcher is in its proper place. If damaged, replace
immediately.
WARNING— THIS EQUIPMENT MAY CREATE SPARKS
Operation Of This Equipment May Create Sparks That Can Start Fires Around Dry
Vegetation. A Spark Arrestor May Be Required. The Operator Should Contact Local
Fire Agencies For Laws Or Regulations Relating To Fire Prevention Requirements.
WARNING— CARBON MONOXIDE
Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains
carbon monoxide, an odorless and deadly gas.
DANGER— ROTATING BLADES
Do not step on the cutting deck.
8
Section 2 — important Safe operation practiceS
Section 2 — important Safe operation practiceS
9
Assembly & Set-Up
3
Contents of Crate
•
•
•
•
•
Riding Mower (1)
•
•
•
•
•
Seat Assembly (1)
•
•
•
•
Discharge Chute Assembly (1)
Mulch Plug (1)
Steering Wheel/Shaft Assembly (1)
Rear Hitch Plate (1)
Rear Engine Cover (1)
Oil Drain Sleeve (1)
Steering Pedestal Cap (1)
Hardware Pack (1)
Product Registration Card (1)
Front Bumper (1)
Rider Operator’s Manual (1)
Engine Operator’s Manual (1)
NOTE: If the tractor will not move or does not move freely
when pushing check if the bypass lever is fully open or the
brake is engaged.
Contents of Hardware Pack
Before beginning installation, remove all the contents from the
crate and all the hardware from the pack to make sure everything
is present. Hardware is listed below.
NOTE: The transmission will NOT engage when the hydrostatic
bypass rod is pulled out. Return the rod to its normal
position prior to operating the tractor. If the tractor will
not move when pushing on the forward/reverse pedals, or
moves slowly, check to see of the bypass valve is on.
•
•
Hitch Plate
Seat Mounting Bracket (with two shoulder bolts & lock nuts
installed)
CAUTION: Never tow your tractor. Towing the
tractor with the rear wheels on the ground may
cause severe damage to the transmission.
Recommended Tools for Assembly
•
•
•
•
•
3/8” Wrench (or Socket)
1/2” Wrench (or Socket)
Phillips Screw Driver
1/4” Drive Ratchet
9/16” Socket
2. Disengage the bypass rod by lifting up and allowing the rod
to move back in after moving the tractor. See Figure 3-1.
Installing the Steering Wheel Assembly
If the steering wheel assembly for your tractor did not come
already installed, follow the steps below:
•
7/16” Wrench
Manually Moving the Tractor
1. Engage the transmission bypass rod to move the tractor
manually without starting it. The transmission bypass rod is
located on the inside of the right tire near the rear of the tractor.
Engage the bypass rod by pulling out and down. See Figure 3-1.
1.
Slide the pedestal cap onto the steering shaft so that when
the steering shaft is installed on the tractor, the pedestal
cap will be upright as shown in Figure 3-2.
Figure 3-2
Figure 3-1
2.
Remove the shoulder bolt and lock nut from the steering
shaft and retain for later steps.
10
3.
4.
With the steering wheel assembly upright and positioned
over the lower steering shaft on the tractor, align the
steering wheel so that with the tractor wheels straight, the
large opening on the steering wheel is facing forward.
Attaching the Seat
If the seat for your tractor was not attached at the factory, follow
the applicable instructions below to attach it.
1.
Remove the shoulder bolts and lock nuts from the seat
mounting bracket included in your hardware pack. See
Figure 3-5.
Lower the steering wheel assembly onto the lower steering
shaft and secure with the shoulder bolt and lock nut
previously removed. See Figure 3-3.
1
Figure 3-5
2.
Remove the two self-tapping bolts factory installed on the
tractor. See Figure 3-6.
2
2
Figure 3-3
5.
6.
Tighten the shoulder bolt and lock nut using a 9/16”
wrench or socket and 7/16”wrench or socket.
Remove the pedestal cap mount screw factory installed
and located on the tractor’s steering console. Retain the
screw for later instructions.
7.
Slide the pedestal cap down onto the tractor and connect the
headlight as shown in the inset of Figure 3-4 (1) and slighty
rotate to the right to clip into place. Secure the pedestal with
the screw (2) previously removed. See Figure 3-4.
Figure 3-6
2
1
Figure 3-4
Section 3 — ASSembly & Set-Up
11
3.
4.
Align the seat bracket in place over the holes from where
the self-tapping bolts were removed, as shown in
Figure 3-7.
7.
To adjust the position of the seat, remove the adjustment
knob on the bottom of the seat. Slide the seat forward or
backward as desired. Retighten the adjustment bolt. Refer
to Figure 3-8.
Using a 1/4-inch drive ratchet with a 3/8” socket, secure the
seat bracket with the self-tapping bolts removed in step 2.
See Figure 3-7.
Installing the Deck Chute
WARNING! NEVER operate this tractor without
either the mulch plug or deck chute installed.
1.
2.
Remove the wing knobs installed on the mowing deck and
retain for later installation.
Install the deck chute into the deck discharge opening on
the deck. The studs on the deck surface will fit through the
holes on the upper portion of the deck chute. The small tab
on the deck lip area will fit through the square cutout on
the lower portion of the deck chute. See Figure 3-9.
NOTE: Make certain that the upper-rear portion of deck
chute is depressing the safety switch located on the deck
surface. The engine will not start without the deck chute
properly in place.
3.
Secure the deck chute by tightening the wing knobs
removed earlier. See Figure 3-9.
1
2
Figure 3-7
CAUTION: Do not use any type of power tool (e.g.
impact gun or electric drill with nut driver attached)
when tightening the self-tapping bolts to attach the
seat bracket.
5.
6.
Position the seat assembly over the seat mounting bracket,
aligning the holes provided.
Install the two shoulder bolts and lock nuts removed from
the seat mounting bracket in Step 1. See Figure 3-8.
Adjustment Knob
Figure 3-9
Installing the Mulch Plug
WARNING! NEVER operate this tractor without
either the mulch plug or deck chute installed.
1.
Remove the wing knobs installed on the mowing deck and
retain for later installation.
Figure 3-8
NOTE: Make sure that the bolt’s shoulder is completely
recessed into the seat bracket when securing the lock nut.
12
Section 3— ASSembly & Set-Up
2.
Install the mulch plug into the deck discharge opening on
the deck. The studs on the deck surface will fit through the
holes on the upper portion of the mulch plug. The small
tab on the deck lip area will fit through the square cutout
on the lower portion of the mulch plug. See Figure 3-10.
3.
Secure the cover with the two hex screws previously
removed. Do not over-tighten.
Installing the Hitch Plate
1.
Remove the factory installed hitch plate mounting
hardware located on the rear of the tractor. See Figure 3-12.
1
2
Figure 3-10
Figure 3-12
NOTE: Make certain that the upper-rear portion of mulch
plug is depressing the safety switch located on the deck
surface. The engine will not start without the mulch plug
properly in place.
2.
Position the hitch plate, packed with the loose parts, with
the flat side up as shown in Figure 3-12. Secure using the
two bolts and hex nuts previously removed.
Installing the Bumper
3.
Secure the mulch plug by tightening the wing knobs
removed earlier.
1.
Remove the two screws as shown in Figure 3-13.
Install the Rear Engine Cover
1.
Remove the two factory installed hex screws located on the
rear engine cover. Retain the screws for later instructions.
See Figure 3-11.
Figure 3-13
2.
Position the bumper over the mounting holes and secure
using the hardware removed in Step 1, as shown in
Figure 3-13.
Figure 3-11
2.
Install the rear engine cover by positioning it in place as
shown in Figure 3-11. Tip the engine cover forward to fit it
into the slots provided, then rotate it backwards to align
the mounting holes.
Section 3 — ASSembly & Set-Up
13
Connecting the Battery Cables
Tire Pressure
CALIFORNIA PROPOSITION 65 WARNING:
WARNING! Equal tire pressure should be
Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
maintained at all times. Never exceed the maximum
inflation pressure shown on the sidewall of the tire.
The recommended operating tire pressure is:
Approximately 10 psi for the rear tires
•
•
CAUTION: When attaching battery cables, always
connect the POSITIVE (Red) wire to its terminal first,
followed by the NEGATIVE (Black) wire.
Approximately 14 psi for the front tires
IMPORTANT: Refer to the tire sidewall for exact tire
manufacturer’s recommended or maximum psi. Do not
overinflate. Uneven tire pressure could cause the cutting deck to
mow unevenly.
For shipping reasons, both battery cables on your equipment
may have been left disconnected from the terminals at the
factory. To connect the battery cables, proceed as follows:
Gas and Oil Fill-up
The gasoline tank is located under the seat. Do not overfill.
NOTE: The positive battery terminal is marked Pos. (+). The
negative battery terminal is marked Neg. (–).
WARNING! Use extreme care when handling
gasoline. Gasoline is extremely flammable and the
vapors are explosive. Never fuel machine indoors or
while the engine is hot or running. Extinguish
cigarettes, cigars, pipes, and other sources of ignition.
1.
2.
Remove the factory installed hex bolts and sems nuts
located on the end of the wiring harness. Retain the
hardware for later instructions.
Remove the plastic cover, if present, from the positive
battery terminal and attach the red cable to the positive
battery terminal (+) with one of the bolts and hex nuts,
previously removed, using a 7/16 inch wrench and socket.
See Figure 3-14.
IMPORTANT: Your tractor is shipped with motor oil in the
engine. However, you MUST check the oil level before
operating. Be careful not to overfill.
Service and check the engine oil as instructed in the Engine
Owner’s Manual packed with your tractor. Read the instructions
carefully.
IMPORTANT: It is important to NOT top off your fuel tank
when filling with fuel. Leave an expansion area available
inside the fuel tank to allow for the fuel to expand and for
proper ventilation. Otherwise the unit may not run properly.
Fill the tank in accordance with Figure 3-15.
Figure 3-14
3.
4.
Remove the plastic cover, if present, from the negative
battery terminal and attach the black cable to the negative
battery terminal (–) with the remaining bolt and hex nut.
See Figure 3-14.
Position the red rubber boot over the positive battery
terminal to help protect it from corrosion.
NOTE: If the battery is put into service after the date shown
on top/side of battery, charge the battery as instructed in
the Service section prior to operating the tractor.
Figure 3-15
14
Section 3— ASSembly & Set-Up
Controls & Features
4
Forward Drive Pedal
Brake Pedal
Parking Brake Lever
Reverse Drive Pedal
Headlight
Fuel Level Indicator
Ignition Switch Module
Fuel Fill Cap
PTO Lever
Throttle/Choke Lever
Deck Lift Lever
Cup Holder
Oil Fill Cap
Figure 4-1
Lawn Tractor controls and features are illustrated in Figure 4-1 and described on the following pages.
WARNING! Read and follow all safety rules and instructions in this manual, including the entire Operation section,
before attempting to operate this machine. Failure to comply with all safety rules and instructions may result in personal
injury.
15
Throttle/Choke Control
The throttle control lever is located on the left
fender of the tractor seated in the operator’s
position; see Figure 4-1. This lever controls the speed
of the engine, as well as the choke when it is pushed
all the way forward. When set in a given position,
the throttle will maintain a uniform engine speed.
Forward Drive Pedal
The forward drive pedal is located on the right side of the machine,
along the running board. Press the forward drive pedal forward to
cause the tractor to travel forward. Ground speed is also controlled
with the forward drive pedal. The further forward the pedal is
pivoted, the faster the tractor will travel. The pedal will return to its
original/neutral position when it’s not pressed.
FAST
IMPORTANT: When operating the tractor with the
cutting deck engaged, be certain that the throttle
lever is always in the FAST (rabbit) position.
Reverse Drive Pedal
The reverse drive pedal is located on the right side of the tractor
along the running board. Ground speed is also controlled with
the reverse drive pedal. The further downward the pedal is
pivoted, the faster the tractor will travel. The pedal will return to
its original/neutral position when it’s not pressed.
Moving the throttle lever all the way forward
activates the engine’s choke control. Activating
the choke control closes the choke plate on the
carburetor and aids in starting the engine.
SLOW
Refer to Starting the Engine in the Operation section
of this manual for detailed starting instructions.
Brake Pedal
The brake pedal is located on the left side of the lawn tractor,
along the running board. Depress the pedal all the way down to
engage the disc brake and bring the tractor to a complete stop.
Ignition Switch Module
The ignition switch module is located on the left fender of the
tractor seated in the operator’s position, adjacent to the Throttle/
Choke Control. To start the engine, insert the key into the ignition
switch module and turn clockwise to the START position. Release
the key into the NORMAL MOWING MODE position once the
engine has fired.
NOTE: The brake pedal must be completely depressed to start
the engine. Refer to Safety Interlock Switches in the Operation
section of this manual.
Parking Brake
To set the parking brake, fully depress the brake pedal. Move the
parking brake lever all the way down and into the parking brake
position. Release the brake pedal to allow the parking brake to
engage.
To stop the engine, turn the ignition key counter-clockwise to the
STOP position. See Figure 4-2.
To release the parking brake, depress the brake pedal and move
the parking brake lever out of the parking brake position. Release
the brake pedal.
Reverse
Push
Button
Indicator
Light
NOTE: The parking brake must be set if the operator leaves the
seat with the engine running or the engine will automatically
shut OFF.
Reverse
Caution
Mode
Normal
Driving
Mode
Deck Lift Lever
Found on your tractor’s right fender, the deck lift lever is used to
change the height of the cutting deck. To use, move the lever to
the left, then place in the notch best suited for your application.
Position
Stop
position
Start
position
PTO Lever
Found on the tractor’s right fender, the PTO (blade engage)
lever is used to engage power to the cutting deck. To operate,
move the lever all the way forward. Moving the lever all the way
rearward into the PTO OFF position disengages power to the
cutting deck.
Figure 4-2
NOTE: The PTO (blade engage) lever must be in the disengaged
WARNING! Never leave a running machine
unattended. Always disengage PTO, set parking
brake, stop engine and remove key to prevent
unintended starting.
(PTO OFF) position when starting the engine.
IMPORTANT: Prior to operating the tractor, refer to both Safety
Interlock Switches and Starting the Engine in the Operation
section of this manual for detailed instructions regarding the
Ignition Switch Module and operating the tractor in REVERSE
CAUTION MODE.
16
Section 4— controlS & FeatureS
Fuel Lever Indicator
The Fuel Lever Indicator is located below the seat on the left
hand side from the operator’s position in the controls panel. Use
this window to identify the tractor’s fuel needs. See Figure 4-4.
Figure 4-3
Fuel Fill Cap
The Fuel Fill Cap is located below the seat. Refer to the Assembly
& Set-up section in this manual for instructions on fueling this
tractor.
Oil Fill Cap
The Oil Fill Cap is located below the seat. Refer to the Assembly
& Set-up section in this manual for instructions on checking and
adding oil to this tractor.
Headlight
The headlight is located on the center of the steering column and
is illuminated when the key is in the ON position.
Transmission Bypass Rod (Not Shown)
The transmission bypass rod is located inside the right tire on the
lower right section of the frame.
When engaged, the rod opens a bypass within the hydrostatic
transmissions, which allows the tractor to be pushed short
distances by hand. Refer to the Assembly & Set-Up section for
instructions on using the bypass feature.
Section 4 — controlS & FeatureS
17
Operation
5
Engaging the Parking Brake
WARNING
To engage the parking brake:
Avoid Serious Injury or Death
Know location and function of all controls.
Remove objects which could be thrown by the blades.
Go up and down slopes, not across.
•
•
•
•
1.
2.
3.
Fully depress the brake pedal and hold it down with your
foot.
Move the parking brake lever down into the parking brake
position.
Use extra caution on slopes. Do not mow slopes greater
than 12 degrees. Avoid sudden turns. Use low speed.
Do not operate machine where it could tip or slip.
If machine stops going uphill, stop blades and back down
slowly.
Release the brake pedal to allow the parking brake to
engage.
•
•
To release the parking brake:
1.
Depress the brake pedal and move the parking brake lever
out of the parking brake position.
•
•
•
Before leaving operator’s position, disengage blades,
engage parking brake, shut off and remove key.
Be sure blades and engine are stopped before placing
hands or feet near blades.
Steering Wheel Height Adjustment
This unit has a telescoping steering column. To adjust the height
of the steering wheel:
Keep safety devices (guards, shields, switches, etc.) in
place and working.
Keep bystanders away.
•
•
•
1.
Sit in the operator’s seat and place your hands on the
steering wheel.
Allow machine to cool before fueling or storing.
Keep machine free of debris.
2.
Push the button (a) on the steering column and raise or
lower the steering wheel (b) to the desired position. See
Figure 5-1.
Read Operator’s Manual
NOTE: Once the desired position is achieved, lift up and
down on the steering wheel to make sure it locks into
place and the button (a) on the steering column releases
into a locked position. Do not operate this unit unless the
steering column is in a locked position.
Safety Interlock Switches
This tractor is equipped with a safety interlock system for the
protection of the operator. If the interlock system should ever
malfunction, do not operate the tractor. Contact an authorized
service dealer.
•
The safety interlock system prevents the engine from
cranking or starting unless the parking brake is engaged,
and the PTO (Blade Engage) lever is in the disengaged (OFF)
position.
•
•
The engine will automatically shut OFF if the operator
leaves the seat before engaging the parking brake.
The engine will automatically shut OFF if the operator
leaves the tractor’s seat with the PTO (Blade Engage) lever
in the engaged (ON) position, regardless of whether the
parking brake is engaged.
b
•
•
With the ignition key in the NORMAL MOWING position,
the PTO (Blade Engage) clutch will automatically shut OFF
if the PTO (Blade Engage) lever is moved into the engaged
(ON) position with the shift lever in position for reverse
travel.
a
The engine will automatically shut OFF if the mulch plug,
deck chute or bagger chute is removed, regardless of
whether the parking brake is engaged or the PTO (Blade
Engage) lever is in the disengaged (OFF) position.
Figure 5-1
WARNING! Do not operate the tractor if the
interlock system is malfunctioning. This system was
designed for your safety and protection.
18
Setting the Cutting Height
Driving the Tractor
1.
Select the height position of the cutting deck by placing
the deck lift lever in any of the different cutting height
notches on the right side of the fender.
WARNING! Avoid sudden starts, excessive speed
and sudden stops.
WARNING! Do not leave the seat of the tractor
without first placing the PTO (Blade Engage) lever in
the disengaged (OFF) position, depressing the brake
pedal and engaging the parking brake. If leaving the
tractor unattended, also turn the ignition key OFF
and remove the key.
WARNING! Keep hands and feet away from the
discharge opening of the cutting deck.
Refer to Leveling the Deck in the Maintenance & Adjustments
section of this manual for more detailed instructions regarding
deck adjustment.
WARNING! Always look down and behind before
and while backing up to avoid a back-over accident.
Starting the Engine
1.
2.
Move the throttle lever into the FAST (rabbit) position.
To travel FORWARD, slowly engage the forward drive pedal
until the desired speed is reached.
WARNING! Do not operate the tractor if the
interlock system is malfunctioning. This system was
designed for your safety and protection.
3.
4.
To travel in REVERSE, slowly engage the reverse drive pedal
until the desired speed is reached.
NOTE: Refer to the Assembly & Set-Up section of this manual for
gasoline and oil fill-up instructions.
The lawn tractor is brought to a stop by depressing the
brake pedal.
1.
2.
Insert the tractor key into the ignition switch module.
WARNING! Before leaving the operator’s position
for any reason, disengage the blade, engage the
parking brake, shut engine OFF and remove the key.
Place the PTO (Blade Engage) lever in the disengaged (OFF)
position.
3.
4.
Engage the tractor’s parking brake.
IMPORTANT: When stopping the tractor for any
reason while on a grass surface, always:
Activate the choke control by moving the throttle/choke
control all the way forward into the choke position.
1.
Make sure the forward and reverse drive pedals are in
neutral.
5.
Turn the ignition key clockwise to the START position.
After the engine starts, release the key. It will return to the
NORMAL MOWING position.
2.
3.
Engage the parking brake.
Shut the engine OFF and remove the key. Doing so will
minimize the possibility of having your lawn ‘‘browned’’ by
hot exhaust from your tractor’s running engine.
CAUTION: Do NOT hold the key in the START
position for longer than ten seconds at a time. Doing
so may cause damage to your engine’s electric
starter.
Operating the Headlight
The headlight is ON whenever the ignition key is rotated out of
the STOP position. The headlight turns OFF when the ignition key
is moved to the STOP position.
6.
After the engine starts, deactivate the choke control by
placing the throttle control into the FAST position.
NOTE: Do NOT operate this unit with the Choke control
activated. Doing so will result in a “rich” fuel mixture and can
cause the engine to run poorly.
Stopping the Engine
WARNING! If you strike a foreign object, stop the
engine, disconnect the spark plug wire and ground
against the engine. Thoroughly inspect the machine
for any damage. Repair the damage before
restarting and operating.
1.
If the blade is engaged, place the PTO (Blade Engage) lever
in the disengaged (OFF) position.
2.
3.
Place the throttle/choke control near the SLOW position.
Turn the ignition key counter-clockwise to the STOP
position.
4.
Remove the key from the ignition switch to prevent
unintended starting.
Section 5 — operation
19
Reverse Caution Mode
The REVERSE CAUTION MODE position of the key switch module
allows the tractor to maneuver in reverse with the blade (PTO)
engaged.
Driving on Slopes
Refer to the SLOPE GAUGE in the Important Safe Operation
Practices section to help determine slopes where you may
operate the tractor safely.
NOTE: Mowing in reverse is not recommended.
WARNING! Do not mow on inclines with a slope in
excess of 12 degrees (a rise of approximately 2 feet for
every 10 feet). The tractor could overturn and cause
serious injury.
WARNING! Use extreme caution while operating
the tractor in the REVERSE CAUTION MODE. Always
look down and behind before and while backing. Do
not operate the tractor when children or others are
around. Stop the tractor immediately if someone
enters the area.
•
•
Mow up and down slopes, NEVER across.
Exercise extreme caution when changing direction on
slopes.
To use the REVERSE CAUTION MODE:
•
•
•
Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.
NOTE: The operator MUST be seated in the tractor seat.
1.
Start the engine as previously instructed on the previous
page.
Avoid turns when driving on a slope. If a turn must be
made, turn down the slope. Turning up a slope greatly
increases the chance of a roll over.
2.
Turn the key from the NORMAL MOWING (Green) position
to the REVERSE CAUTION MODE (Yellow) position of the
key switch module. See Figure 5-2.
Avoid stopping when driving up a slope. If it is necessary
to stop while driving up a slope, start up smoothly and
carefully to reduce the possibility of flipping the tractor
over backward.
Reverse
Push
Button
Indicator
Light
Engaging the PTO (Cutting Blade)
Engaging the PTO (Blade Engage) transfers power to the cutting
Reverse
Caution
Mode
deck. To engage the blade, proceed as follows:
Normal
Driving
Mode
1.
2.
Move the throttle control lever to the FAST (rabbit) position.
Position
Grasp the PTO (Blade Engage) lever and pivot it all the way
forward into the engaged (ON) position.
Stop
position
NOTE: Keep the throttle lever in the FAST (rabbit) position
for the most efficient use of the cutting deck.
Start
IMPORTANT: The PTO (Blade Engage) lever must be in the
disengaged (OFF) position when starting the engine, when
traveling in reverse, and if the operator leaves the seat. Refer to
Safety Interlock Switches in the Operation section of this manual.
position
Figure 5-2
Mulching
3.
Press the REVERSE PUSH BUTTON (Orange, Triangular
Button) at the top, right corner of the key switch module.
The red indicator light at the top, left corner of the key
switch module will be ON while activated. See Figure 5-2.
A mulch kit has been supplied with your unit. Mulching is a
process of recirculating grass clippings repeatedly beneath
the cutting deck. The ultra-fine clippings are then forced back
into the lawn where they act as a natural fertilizer. Refer to the
Assembly & Set-up section of this manual for instructions on how
to install the mulch kit.
4.
5.
Once activated (indicator light ON), the tractor can be
driven in reverse with the cutting blade (PTO) engaged.
Always look down and behind before and while backing to
make sure no children are around. After resuming forward
motion, return the key to the NORMAL MOWING position.
The REVERSE CAUTION MODE will remain activated until:
a. the key is placed in either the NORMAL MOWING
position or STOP position or,
b. the operator leaves the seat.
20
Section 5— operation
Using the Deck Lift Lever
To raise the cutting deck, move the deck lift lever to the left,
then place it in the notch best suited for your application. Refer
to Setting the Cutting Height in this section.
Mowing
WARNING! To help avoid blade contact or a
thrown object injury, keep bystanders, helpers,
children and pets at least 75 feet from the machine
while it is in operation. Stop machine if anyone
enters the area.
The following information will be helpful when using the
cutting deck with your tractor:
WARNING! Plan your mowing pattern to avoid
discharge of materials toward roads, sidewalks,
bystanders and the like. Also, avoid discharging
material against a wall or obstruction which may
cause discharged material to ricochet back toward
the operator.
•
•
Do not mow at high ground speed, especially if a mulch
kit or grass collector is installed.
For best results it is recommended that the first two laps
be cut with the discharge thrown towards the center.
After the first two laps, reverse the direction to throw the
discharge to the outside for the balance of cutting. This
will give a better appearance to the lawn.
•
•
•
•
Do not cut the grass too short. Short grass invites weed
growth and yellows quickly in dry weather.
Mowing should always be done with the engine at full
throttle.
Under heavier conditions it may be necessary to go back
over the cut area a second time to get a clean cut.
Do NOT attempt to mow heavy brush and weeds and
extremely tall grass. Your tractor is designed to mow
lawns, NOT clear brush.
•
Keep the blade sharp and replace the blade when worn.
Refer to Cutting Blade in the Service section of this manual
for proper blade sharpening instructions.
Section 5 — operation
21
Maintenance & Adjustments
6
Maintenance Schedule
Before
Every
Every
Every
Every
Prior
Each use
10 Hours
25 Hours
50 Hours
100 Hours
to Storing
Check Engine Oil Level
P P
P
Check Air Filter for Dirty, Loose or Damaged Parts
Clean and Re-oil Air Filter’s Foam Pre-cleaner
(if Equipped)
P
Replace Air Filter Element
P
Change Engine Oil and Replace Oil Filter
(if Equipped)
P
Clean Battery Terminals
Lube Front Axles and Rims
Clean Engine Cooling Fins
Check Spark Plug Condition & Gap
Replace Fuel Filter
P
P
P
P
P
P
P P
P
IMPORTANT: It is important to consult the specific Engine Operator’s Manual included with this machine for detailed engine
maintenance procedures and intervals.
2.
3.
Locate the oil drain valve on the right side of the engine
and the oil fill cap on the topside of the engine.
Maintenance
WARNING: Before performing any maintenance or
Unscrew the oil fill cap and remove the dipstick from the oil
fill tube.
repairs, disengage PTO, set parking brake, stop
engine and remove key to prevent unintended
starting.
Engine
Refer to the Engine Owner’s Manual for engine maintenance
instructions.
Check engine oil level before each use as instructed in the Engine
Owner’s Manual packed with your unit. Follow the instructions
carefully.
Changing Engine Oil
For draining oil from the engine’s crankcase, proceed as follows:
1.
Run the engine for a few minutes to allow the oil in the
crankcase to warm up. Warm oil will flow more freely and
carry away more of the engine sediment which may have
settled at the bottom of the crankcase. Use care to avoid
burns from hot oil.
22
4.
Snap the small end of oil drain sleeve onto the space
provided around the oil drain plug. See Figure 6-1.
Rear Wheels
The rear wheels should be removed from the axles once a
season. Lubricate the axles and the rims well with an all-purpose
grease before re-installing them.
Front Axles
Each end of the tractor’s front pivot bar may be equipped with a
grease fitting. Lubricate with a grease gun after every 25 hours of
tractor operation.
Steering Rack & Pinion
Once per season, or every 25 hours of operation, it will be
necessary to lubricate the steering rack and pinion gear located
under the front of the unit. Using standard automotive grease,
apply grease to the front side and rear side of the steering rack,
as indicated in Figure 6-2.
Figure 6-1
5.
6.
Remove the oil drain plug and drain the oil into a suitable
container with a capacity of no less than 64 oz.
Tip the tractor slightly in the direction of the suitable
container to aid in fully draining all of the oil from the
engine.
WARNING! Before tipping engine or equipment to
drain oil, drain fuel from tank by running engine
until fuel tank is empty.
7.
Replace the oil drain plug and tighten. Be careful not to
overtighten the oil drain plug.
Figure 6-2
Cleaning the Engine & Deck
8.
Refill the engine with new motor oil as instructed in the
Engine Owner’s Manual packed with your unit.
If the engine has been running, allow it to cool for at least half
an hour before cleaning. Periodically remove dirt build-up from
engine. Clean cooling fins every 25 hours. Clean with a brush or
compressed air.
IMPORTANT: Refer to the Engine Owner’s Manual packed with
your unit for information regarding the quantity and proper
viscosity of motor oil.
IMPORTANT: Do not spray engine with water to clean because
water could contaminate fuel. Using a garden hose or pressure
washing equipment can also force water into the air cleaner or
muffler opening. Water in the air cleaner will soak the paper
element, and water that passes through the element or muffler
can enter the cylinder, causing damage.
Lubrication
WARNING: Before lubricating, repairing, or
inspecting, always disengage PTO, set parking brake,
stop engine and remove key to prevent unintended
starting.
Any fuel or oil spilled on the machine should be wiped off
promptly. Do NOT allow debris to accumulate around the cooling
fins of the engine or on any other part of the machine.
Engine
Lubricate the engine with motor oil as instructed in the Engine
Owner Manual packed with your unit.
IMPORTANT: The use of a pressure washer to clean your
tractor is NOT recommended. It may cause damage to electrical
components, spindles, pulleys, bearings or the engine.
Pivot Points & Linkage
Lubricate all the pivot points on the drive system, parking brake
and lift linkage at least once a season with light oil.
WARNING! Accumulation of debris around muffler
could cause a fire. Inspect and clean before every
use.
Section 6 — Maintenance & adjuStMentS
23
4.
Attach the hose coupler to the water port on your deck’s
surface. See Figure 6-3.
Muffler
WARNING! Temperature of muffler and nearby
engine areas may exceed 150˚F (65˚C). Avoid contact
with these areas.
Inspect muffler periodically, and replace if necessary.
Replacement parts for the muffler must be the same and
installed in the same position as the original parts.
Battery
The battery is sealed and is maintenance-free. Acid levels cannot
be checked.
•
•
•
Always keep the battery cables and terminals clean and
free of corrosive build-up.
After cleaning the battery and terminals, apply a light coat
of petroleum jelly or grease to both terminals.
Always keep the rubber boot positioned over the positive
terminal to prevent shorting.
IMPORTANT: If removing the battery for any reason,
disconnect the NEGATIVE (Black) wire from it’s terminal first,
followed by the POSITIVE (Red) wire. When re-installing the
battery, always connect the POSITIVE (Red) wire its terminal
first, followed by the NEGATIVE (Black) wire. Be certain that the
wires are connected to the correct terminals; reversing them
could change the polarity and result in damage to your engine’s
alternating system.
Figure 6-3
5.
6.
Turn the water ON.
While sitting in the operator’s position on the tractor, start
the engine and place the throttle lever in the FAST (rabbit)
position.
Cleaning Battery
Clean the battery by removing it from the tractor and washing
with a baking soda and water solution. If necessary, scrape the
battery terminals with a wire brush to remove deposits. Coat
terminals and exposed wiring with grease or petroleum jelly to
prevent corrosion.
7.
Move the tractor’s PTO (Blade Engage) into the ON position.
8.
Remain in the operator’s position with the cutting deck
engaged for a minimum of two minutes, allowing the
underside of the cutting deck to thoroughly rinse.
9.
Move the tractor’s PTO (Blade Engage) into the OFF
position.
Cleaning the Tractor
Any fuel or oil spilled on the machine should be wiped off
promptly. Do NOT allow debris to accumulate around the cooling
fins of the engine, the transmission’s cooling fan or on any other
part of the machine, especially the belts and pulleys.
10. Turn the ignition key to the STOP position to turn the
tractor’s engine OFF.
11. Turn the water OFF and detach the hose coupler from the
water port on your deck’s surface.
Deck Wash System
Your tractor’s deck is equipped with a water port on its surface as
part of its deck wash system.
After cleaning your deck with the deck wash system, return to
the operator’s position and engage the PTO. Keep the cutting
deck running for a minimum of two minutes, allowing the
underside of the cutting deck to thoroughly dry.
Use the deck wash system to rinse grass clippings from the
deck’s underside and prevent the buildup of corrosive chemicals.
Complete the following steps AFTER EACH MOWING:
Adjustments
WARNING: Never attempt to make any
adjustments while the engine is running, except
where specified in the Operator’s Manual.
1.
Drive the tractor to a level, clear spot on your lawn, near
enough for your garden hose to reach.
CAUTION: Make certain the tractor’s discharge
chute is directed AWAY from your house, garage,
parked cars, etc.
Seat Adjustment
Refer to the Set-Up and Assembly section of this manual for seat
adjustment instructions.
2.
3.
Disengage the PTO (Blade Engage), set the parking brake
and stop the engine.
Thread the hose coupler (packaged with your tractor’s
Operator’s Manual) onto the end of your garden hose.
24
Section 6— Maintenance & adjuStMentS
Parking Brake Adjustment
Tires
WARNING: Never attempt to adjust the brakes
WARNING! Never exceed the maximum inflation
while the engine is running. Always disengage PTO,
stop engine and remove key to prevent unintended
starting.
pressure shown on the sidewall of the tire.
The recommended operating tire pressure is:
If the tractor does not come to a complete stop when the brake
pedal is completely depressed, or if the tractor’s rear wheels
can roll with the parking brake applied, the brake is in need of
adjustment. See an authorized service dealer to have your brakes
properly adjusted.
•
•
Approximately 10 psi for the rear tires
Approximately 14 psi for the front tires
IMPORTANT: Refer to the tire sidewall for exact tire
manufacturer’s recommended or maximum psi. Do not over-
inflate. Uneven tire pressure could cause the cutting deck to
mow unevenly.
Leveling the Deck
NOTE: Check the tractor’s tire pressure before performing any
deck leveling adjustments. Refer to Tires, later in this section of
this manual for more information regarding tire pressure.
Off Season Storage
WARNING! Never store lawn tractor with fuel in
tank indoors or in poorly ventilated areas where fuel
fumes may reach an open flame, spark, or pilot light
as on a furnace, water heater, clothes dryer, or gas
appliance.
Front To Rear
It is possible to adjust the pitch of the cutting deck. The front of
the deck should be between 0” (level) and 1⁄4” lower than the rear
of the deck. Adjust if necessary as follows:
1.
With the tractor parked on a firm, level surface, place the
lever for lifting the platform in the middle position and
rotate the blade so that it is aligned with the front and rear
of the tractor.
Preparing the Engine
IMPORTANT: Fuel left in the fuel tank during warm weather
deteriorates and will cause serious starting problems.
To prevent gum deposits from forming inside the engine’s
carburetor and causing possible malfunction of the engine, the
fuel system must be either completely emptied, or the gasoline
must be treated with a stabilizer to prevent deterioration.
2.
Measure the distance from the front of the blade tip to the
ground and the rear of the blade tip to the ground. The
first measurement taken should be between 0” (level) and
1⁄4” less than the second measurement. Determine the
approximate distance necessary for proper adjustment and
proceed, if necessary, to the next step.
1.
If using a fuel stabilizer:
•
•
•
Read the product manufacturer’s instructions and
recommendations.
3.
Locate the flange lock nut on the front end of the PTO Lift
Rod. See Figure 6-4.
Add to clean, fresh gasoline the correct amount of
stabilizer for the capacity of the fuel system.
Fill the fuel tank with treated fuel and run the
engine for 2-3 minutes to get stabilized fuel into the
carburetor.
2.
If emptying the fuel system:
•
•
Do not drain fuel when the engine is hot. Allow the
engine adequate time to cool. Drain fuel into an
approved container outdoors, away from open flame.
Drain any large volume of fuel from the tank by
disconnecting the fuel line from the in-line fuel filter
near the engine. See the complete instructions for
Draining the Fuel in this section.
WARNING! Gasoline is extremely flammable and
can be explosive under certain conditions. Drain
gasoline before storing the equipment for extended
periods. Drain fuel only into an approved container
outdoors, away from an open flame. Allow engine to
cool. Extinguish cigarettes, cigars, pipes, and other
sources of ignition prior to draining fuel. Store
gasoline in an approved container in safe location.
Figure 6-4
•
•
Tighten the flange lock nut to raise the front of the
deck;
•
Reconnect the fuel line and run the engine until it starts
to falter, then use the choke to keep the engine running
until all fuel in the carburetor has been exhausted.
Loosen the flange lock nut to lower the front of the
deck.
Section 6 — Maintenance & adjuStMentS
25
•
•
Disconnect the fuel line and drain any remaining
gasoline from the system.
WARNING! Gasoline is a toxic substance. Dispose
of gasoline properly. Contact your local authorities
for approved disposal methods.
Remove the spark plug and pour one ounce of engine
oil through the spark plug hole into the cylinder. Crank
the engine several times to distribute the oil. Replace
the spark plug.
Draining the Fuel
1.
Locate the fuel filter, which is located on the left side of the
engine, and may be attached to the engine with a tie strap.
2.
Cut the tie strap, if present, then pinch the in-line clamp
on the fuel filter with a pair of pliers, slide the clamp up the
fuel line.
3.
Pull the fuel line free from the filter and place the open end
of the line into an approved container to drain the fuel.
Preparing the Lawn Tractor
1.
2.
3.
Clean and lubricate tractor thoroughly as described in the
Lubrication instructions.
Do not use a pressure washer or garden hose to clean your
unit.
Store mower in a dry, clean area. Do not store next to
corrosive materials, such as fertilizer.
26
Section 6— Maintenance & adjuStMentS
Service
7
5.
Remove the remaining bow-tie cotter pins securing the
deck to the unit, as shown in Figure 7-3.
Cutting Deck Removal
To remove the cutting deck, proceed as follows:
1.
2.
3.
Place the PTO (Blade Engage) lever in the disengaged (OFF)
position and engage the parking brake.
Lower the deck by moving the deck lift lever into the
bottom notch on the right fender.
Remove the bow-tie cotter pin and flat washer from the
deck lift assembly, and retain for reinstallation later. See
Figure 7-1.
Figure 7-3
NOTE: The bow-tie clips should be re-installed from the top
down.
6.
7.
Unplug the wire pigtail from the deck switch.
Move the deck lift lever into the top notch on the right
fender to raise the deck lift arms up and out of the way.
8.
Carefully remove the PTO cable from the rear of the cutting
deck. Remove the spring from the deck idler bracket. See
Figure 7-4.
Figure 7-1
4.
Remove the belt from around the tractor’s PTO pulley. See
Figure 7-2.
Figure 7-4
9.
Gently slide the cutting deck (from the left side) out from
underneath the tractor.
Figure 7-2
27
6.
Remove the belt keeper by removing the hex bolt that
secures it. See Figure 7-6.
Changing the Deck Belt
NOTE: It is possible to change the deck belt with the cutting
deck still installed on the tractor; however it is much easier to
remove the deck first, change the deck belt, then reinstall the
cutting deck.
To change the cutting deck belt, proceed as follows:
1.
It is easiest to change the deck belt by first removing the
cutting deck as instructed earlier in this section first. Skip
this step if deciding to change the deck belt with the
mowing deck still installed on the unit. Otherwise, remove
the cutting deck now.
2.
3.
If changing the deck belt with the cutting deck still
installed on the unit, lower the deck to the lowest mowing
position.
Remove the deck belt from around the unit’s PTO drive
pulley as shown in Figure 7-2. Simply roll one side of the
belt OFF of the pulley and then work it OFF the pulley by
continuing around the pulley until the belt is OFF of the
pulley.
Belt Keeper Hex Bolt
4.
5.
Pull the belt towards the front of the unit, pulling it through
and out of the belt keeper rod.
Figure 7-6
Remove the deck belt cover by removing the three hex
bolts that secure it. See Figure 7-5.
7.
Change the belt then reinstall the all the components
removed in the reverse order beginning with the idler
pulley, and then belt cover.
8.
Feed the deck belt through the belt keeper rod and work it
around and onto the PTO drive pulley as shown in Figure 7-2.
Battery
CALIFORNIA PROPOSITION 65 WARNING!
Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
CAUTION: If removing the battery, disconnect the
NEGATIVE (Black) wire from it’s terminal first,
followed by the POSITIVE (Red) wire. When re-
installing the battery, always connect the POSITIVE
(Red) wire its terminal first, followed by the
NEGATIVE (Black) wire.
Battery Failures
Some common causes for battery failure are:
•
•
•
•
•
Incorrect initial activation
Overcharging
Figure 7-5
Freezing
Undercharging
Corroded connections
These failures are NOT covered by your tractor’s warranty.
28
Section 7— Service
Jump Starting
Cutting Blade
WARNING! Never jump start a damaged or frozen
WARNING! Shut the engine OFF and remove
battery. Be certain the vehicles do not touch, and
ignitions are off. Do not allow cable clamps to touch.
ignition key before removing the cutting blade(s) for
sharpening or replacement. Protect your hands by
using heavy gloves when grasping the blade.
1.
2.
3.
4.
Connect positive (+) cable to positive post (+) of your
tractor’s discharged battery.
WARNING! Periodically inspect the blade spindles
for cracks or damage, especially if you strike a
foreign object. Replace immediately if damaged.
Connect the other end of the cable to the (positive +) post
of the jumper battery.
Connect the second cable (negative –) to the other post of
the jumper battery.
The blades may be removed as follows.
NOTE: It may be easier to change the blade by first
removing the deck from beneath the tractor, (refer to
Cutting Deck Removal earlier in this section) then gently
flip the deck over to expose its underside. It is possible to
change the blade, however, with the deck still attached to
the tractor. If attempting to change the blade with the deck
still installed on the tractor, first move the deck lift lever to
its highest cutting position.
Make the final connection on the engine block of the
tractor, away from the battery. Attach to a unpainted part
to assure a good connection.
CAUTION: If the jumper battery is installed on a
vehicle (i.e. car, truck), do NOT start the vehicle’s
engine when jump starting your tractor.
5.
6.
Start the tractor as instructed in the Operation section of
this manual.
1.
2.
Remove the mulch plug, deck chute or bagging chute, if
equipped, exposing the deck chute opening.
Set the tractor’s parking brake before removing the jumper
cables, in reverse order of connection.
Using a block of wood or 2 x 4, insert it into the deck
opening and rotate the blade around until it wedges the
wood between the deck opening and the cutting blade, as
shown in Figure 7-7.
Charging
WARNING! Batteries give off an explosive gas
while charging. Charge the battery in a well
ventilated area and keep away from an open flame
or pilot light as on a water heater, space heater,
furnace, clothes dryer or other gas appliances.
CAUTION: When charging your tractor’s battery,
use only a charger designed for 12V lead-acid
batteries. Read your battery charger’s Owner’s
Manual prior to charging your tractor’s battery.
Always follow its instructions and heed its warnings.
If your tractor has not been put into use for an extended period
of time, charge the battery as follows:
1.
Set your battery charger to deliver a max of 10A.
If your battery charger is automatic, charge the battery until the
charger indicates that charging is complete. If the charger is not
automatic, charge for no fewer than eight hours.
Figure 7-7
Fuse
3.
Remove the hex flange nut that secures the blade to the
spindle assembly. See the Inset of Figure 7-7.
One 15A fuse is installed in your tractor’s wiring harness located
just above the battery, under the left fender, to protect the
tractor’s electrical system from damage caused by excessive
amperage.
NOTE: The deck spindle has a normal thread. To loosen,
rotate the flange lock nut counter-clockwise.
If the electrical system does not function, or your tractor’s engine
will not crank, first check to be certain that the fuse has not
blown. It can be found at the rear of the unit, underneath the
fender located by the battery.
WARNING! Always use a fuse with the same
amperage capacity for replacement.
Section 7 — Service
29
4.
To properly sharpen the cutting blades, remove equal
amounts of metal from both ends of the blades along the
cutting edges, parallel to the trailing edge, at a 25°- to 30°
angle. Always grind each cutting blade edge equally to
maintain proper blade balance. See Figure 7-8.
Changing the Transmission Drive Belt
NOTE: Several components must be removed and special tools
(i.e. air/impact wrench) in order to change the tractor’s drive belt.
See an authorized service dealer to have your drive belt replaced
or phone Customer Support to find a dealer near you.
See page 2 for details.
Figure 7-8
WARNING! If the cutting edge of the blade has
previously been sharpened, or if any metal
separation is present, replace the blades with new
ones.
WARNING! A poorly balanced blade will cause
excessive vibration, may cause damage to the
tractor and/or result in personal injury.
5.
Test the blade’s balance using a blade balancer. Grind
metal from the heavy side until it balances evenly.
NOTE: When replacing the blade, be sure to install the
blade with the side of the blade marked ‘‘Bottom’’ (or with
a part number stamped in it) facing the ground when the
mower is in the operating position.
CAUTION! Use a torque wrench to tighten the
blade spindle hex flange nut to between 70 lbs-ft
and 90 lbs-ft.
30
Section 7— Service
Troubleshooting
8
Problem
Cause
Remedy
1. Place blade engage lever in disengaged
(OFF) position.
Engine fails to start
1. PTO/Blade engaged.
2. Spark plug wire disconnected.
3. Fuel tank empty, or stale fuel.
2. Connect wire to spark plug.
3. Fill tank with clean, fresh (less than 30 days
old) gas.
4. Choke not activated.
5. Faulty spark plug.
6. Blown fuse.
4. Place the throttle control in CHOKE position.
5. Clean, adjust gap or replace plug.
6. Replace fuse(s)
7. Engine flooded.
7. Crank engine with throttle in FAST position.
8. Engage parking brake.
8. Parking brake not engaged.
9. Deck chute or mulch plug not poperly
installed.
9. Check the installation of the deck chute or
mulch plug.
Engine runs erratic
1. Unit running with CHOKE activated.
1. Move the throttle control out of the CHOKE
position.
2. Spark plug wire loose.
2. Connect and tighten spark plug wire.
3. Blocked fuel line or stale fuel.
3. Clean fuel line; fill tank with clean, fresh
gasoline and replace fuel filter
4. Vent in gas cap plugged.
5. Water or dirt in fuel system.
4. Clear vent or replace cap if damaged.
5. Drain fuel tank. Refill with clean, fresh
gasoline.
6. Dirty air cleaner.
6. Replace air cleaner paper element and clean
the foam pre-cleaner, if applicable.
Engine overheats
1. Engine oil level low.
1. Fill crankcase with proper amount and
weight of oil.
2. Air flow restricted.
2. Clean grass clippings and debris from around
the engine’s cooling fins and blower housing.
Engine hesitates at high
RPM
1. Spark plug gap too close.
1. Remove spark plug and reset the gap.
Engine idles rough
1. Spark plug fouled, faulty or gap too wide.
2. Dirty air cleaner.
1. Replace spark plug. Set plug gap.
2. Replace air cleaner paper element and clean
the foam pre-cleaner, if applicable.
Excessive vibration
1. Cutting blade loose or unbalanced.
1. Tighten blade and spindle. Balance blade.
2. Damaged or bent cutting blade.
1. Engine speed too low.
2. Replace blade.
Mower will not mulch grass
1. Place throttle in FAST (rabbit) position.
2. Wet grass.
2. Do not mulch when grass is wet.
3. Excessively high grass.
3. Mow once at a high cutting height, then
mow again at desired height or make a
narrower cutting swath.
4. Dull blade.
4. Sharpen or replace blade.
Uneven cut
1. Deck not leveled properly.
1. Perform the Leveling the Deck adjustment.
2. Dull blade.
2. Sharpen or replace blade.
3. Uneven tire pressure.
3. Check tire pressure in all four tires.
31
Replacement Parts
9
Component
Part Number and Description
954-05001
954-05130
Deck Belt
Drive Belt
918-04822B
942-04385
Deck Spindle
Blade
925-1707D
Battery
951-12179B
951-12426A
Fuel Tank Cap (49-State models)
Fuel Tank Cap (California models)
625-05000
Key
634-04726
734-04640
Complete Front Wheel, 13 x 5 x 6
Tire, 16.0 x 6.5 x 8.0
634-0139
734-04641
Complete Rear Wheel, 16.0 x 6.5 x 8.0
Tire, 16.0 x 6.5 x 8.0
946-04829A
Throttle Control/Cable
731-10267
Discharge Chute Assembly
951-10292
937-05065
Spark Plug
Air Filter
951-12690
951-3013
Oil Filter
Fuel Filter
Cub Cadet Genuine Parts can be ordered through your local authorized Cub Cadet dealer, online at cubcadet.com or by phone at
1-800-965-4CUB. To locate your nearest authorized Cub Cadet dealer, visit cubcadet.com or call 1-877-282-8684.
32
Attachments & Accessories
10
The following attachments and accessories are compatible for Mini-Rider Lawn Tractors. See the retailer from which you purchased your
tractor, an authorized MTD Service Dealer or phone (800) 800-7310 for information regarding price and availability.
CAUTION: The Mini-Rider Lawn Tractors are NOT designed for use with any type of ground-engaging attachments (e.g. tiller
or plow). Use of this type of equipment WILL void the tractor’s warranty.
Model Number
Description
Bagger
Mulch Kit
19A30014OEM
19A30013OEM
19A40026100
490-850-0008
490-290-0013
490-900-0045
490-850-0005
490-850-0018
Hauler
Siphon Pump
Tractor Cover
Oil Filter Wrench
Blade Removal Tool
Extended Spark Plug Wrench
33
FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
MTD Consumer Group Inc, the United States Environmental Protection Agency (EPA), and for those products certified for sale in the state of
California, the California Air Resources Board (CARB) are pleased to explain the evaporative emission control system (ECS) warranty on your
2015-2016 small off-road equipment (outdoor equipment). In California, new outdoor equipment must be designed, built and equipped to
meet the State’s stringent anti-smog standards (in other states, outdoor equipment must be designed, built, and equipped to meet the U.S. EPA
small off-road spark ignition engine regulations). MTD Consumer Group Inc must warrant the ECS on your outdoor equipment for the period of
time listed below, provided there has been no abuse, neglect, or improper maintenance of the outdoor equipment.
Your ECS may include parts such as fuel tanks, fuel lines, fuel caps, valves, canisters, filters, vapor hoses, clamps, connectors, and other
associated emission-related components.
Where a warrantable condition exists, MTD Consumer Group Inc will repair your outdoor equipment at no cost to you including diagnosis,
parts, and labor.
MANUFACTURER’S WARRANTY COVERAGE:
This emission control system is warranted for two years. If any emission-related part on your outdoor equipment is defective, the part will be
repaired or replaced by MTD Consumer Group Inc.
OWNER’S WARRANTY RESPONSIBILITIES:
As the outdoor equipment owner, you are responsible for performance of the required maintenance listed in your owner’s manual. MTD
Consumer Group Inc recommends that you retain all receipts covering maintenance on your outdoor equipment, but MTD Consumer Group Inc
cannot deny warranty solely for the lack of receipts.
As the outdoor equipment owner, you should however be aware that MTD Consumer Group Inc may deny you warranty coverage if your
outdoor equipment or a part has failed due to abuse, neglect, improper maintenance, or unapproved modifications.
You are responsible for presenting your outdoor equipment to MTD Consumer Group Inc’s distribution center or service center as soon as
the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question
regarding your warranty coverage, you should contact the MTD Consumer Group Inc Service Department at 1-800-800-7310 or at
GENERAL EMISSIONS WARRANTY COVERAGE:
MTD Consumer Group Inc warrants to the ultimate purchaser and each subsequent purchaser that the outdoor equipment is: (1) designed,
built, and equipped so as to conform with all applicable regulations; and (2) free from defects in materials and workmanship that cause the
failure of a warranted part for a period of two years.
The warranty period begins on the date the outdoor equipment is delivered to an ultimate purchaser or first placed into service.
Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:
1.
Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied is warranted for
the warranty period stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by MTD
Consumer Group Inc according to subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the
remainder of the period.
2.
3.
Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period
stated above. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.
Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the
period of time before the first scheduled replacement date for that part. If the part fails before the first scheduled replacement, the part
will be repaired or replaced by MTD Consumer Group Inc according to subsection (4) below. Any such part repaired or replaced under
warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part.
4.
5.
6.
7.
Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no charge
to the owner.
Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers that are franchised to
service the subject engines or equipment.
The outdoor equipment owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective, emission-
related warranted part, provided that such diagnostic work is performed at a warranty station.
MTD Consumer Group Inc is liable for damages to other engine or equipment components proximately caused by a failure under
warranty of any warranted part.
8.
9.
Throughout the off-road engine and equipment warranty period stated above, MTD Consumer Group Inc will maintain a supply of
warranted parts sufficient to meet the expected demand for such parts.
Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to
the owner. Such use will not reduce the warranty obligations of MTD Consumer Group Inc.
10. Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or
modified parts by the ultimate purchaser will be grounds for disallowing a warranty claim. MTD Consumer Group Inc will not be liable to
warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.
WARRANTED PARTS:
The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage
if MTD Consumer Group Inc demonstrates that the outdoor equipment has been abused, neglected, or improperly maintained, and that
such abuse, neglect, or improper maintenance was the direct cause of the need for repair or replacement of the part. That notwithstanding,
any adjustment of a component that has a factory installed, and properly operating, adjustment limiting device is still eligible for warranty
coverage. Further, the coverage under this warranty extends only to parts that were present on the off-road equipment purchased.
The following emission warranty parts are covered (if applicable):
1.
Fuel Metering System
•
•
Fuel pump
Fuel tank
2.
Evaporative Control
•
•
•
•
•
Fuel hose
Fuel hose clamps
Tethered fuel cap
Carbon canister
Vapor lines
063015 Rev. C
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY FOR
CC-30 RIDER
IMPORTANT: To obtain warranty coverage owner must present an
Without limiting the foregoing, this limited warranty does not provide
coverage in the following cases:
original proof of purchase and applicable maintenance records to the
servicing dealer. Please see the operator’s manual for information on
required maintenance and service intervals.
a.
Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior
finish due to use or exposure.
The limited warranty set forth below is given by Cub Cadet LLC with
respect to new merchandise purchased or leased and used in the United
States and/or its territories and possessions, and by MTD Products Limited
with respect to new merchandise purchased or leased and used in
Canada and/or its territories and possessions (either entity respectively,
“Cub Cadet”).
b.
c.
Service completed by someone other than an authorized
service dealer.
Cub Cadet does not extend any warranty for products sold
or exported outside of the United States and/or Canada, and
their respective possessions and territories, except those sold
through Cub Cadet’s authorized channels of export distribution.
This warranty is in addition to any applicable emissions warranty provided
with your product.
Cub Cadet warrants this product (excluding its Normal Wear Parts,
Batteries, and Attachments as described below) against defects in
material and workmanship for a period of three (3) years or one hundred
twenty (120) operation hours, whichever comes first, commencing on
the date of original retail purchase or lease and will, at its option, repair
or replace, free of charge, any part found to be defective in materials or
workmanship.
d.
e.
Replacement parts and/or accessories that are not genuine Cub
Cadet parts.
Transportation charges and service calls.
There are no implied warranties, including without limitation any
implied warranty of merchantability or fitness for a particular
purpose. No warranties shall apply after the applicable period
of express written warranty above. No other express warranties
beyond those mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product, shall bind
Cub Cadet. The exclusive remedy is repair or replacement of the
product as set forth above.
Normal Wear Parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of original
purchase or lease. Normal wear parts include, but are not limited to items
such as: belts, blades, blade adapters, grass bags, rider deck wheels,
seats, and tires.
Batteries have a one-year prorated limited warranty against defects in
material and workmanship, with 100% replacement during the first three
months. After three months, the battery replacement credit is based on
the months remaining in the twelve (12) month period dating back to
the original date of original sale or lease. Any replacement battery will be
warranted only for the remainder of the original warranty period.
The terms of this warranty provide the sole and exclusive remedy
arising from the sale and/or lease of the products covered hereby.
Cub Cadet shall not be liable for any incidental or consequential
loss or damage including, without limitation, expenses incurred for
substitute or replacement lawn care services or for rental expenses
to temporarily replace a warranted product.
Attachments — Cub Cadet warrants attachments for this product against
defects in material and workmanship for a period of two (2) years,
commencing on the date of the attachment’s original purchase or lease.
Attachments include, but are not limited to items such as: grass collectors
and mulch kits.
Some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of the
product shall void this warranty. You assume the risk and liability for
loss, damage, or injury to you and your property and/or to others and
their property arising out of the misuse or inability to use the product.
This limited warranty shall only apply if this product has been operated
and maintained in accordance with the Operator’s Manual furnished with
the product, and has not been subject to misuse, abuse, neglect, accident,
improper maintenance, alteration, vandalism, theft, fire, water, or damage
because of other peril or natural disaster. Damage resulting from the
installation or use of any part, accessory or attachment not approved by
Cub Cadet for use with the product(s) covered by this manual will void
your warranty as to any resulting damage. In addition, Cub Cadet may
deny warranty coverage if the hour meter, or any part thereof, is altered,
modified, disconnected or otherwise tampered with.
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited warranty
gives you specific legal rights, and you may also have other rights that
vary in different jurisdictions.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF
PURCHASE AND APPLICABLE MAINTENANCE RECORDS, through your local
authorized service dealer. To locate the dealer in your area:
In the U.S.A.
Check your Yellow Pages, or contact Cub Cadet LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, call 1-877-282- 8684
In Canada:
Contact MTD Products Limited, Kitchener, ON N2G 4J1, call 1-800-668-
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019, Phone: 1-877-282-8684
MTD Products Limited, Kitchener, ON N2G 4J1, Phone: 1-800-668-1238
065142 REV. A
|