PU-506-KIT
3-Play HDBaseT™ Extender Kit (2-way IR, RS-232 & HDMI,
up to 100m)
OPERATION MANUAL
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer file, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2020 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
3
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
•
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
•
•
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
•
•
Do not attach the power supply cabling to building surfaces.
Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
•
•
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE
SUMMARY OF CHANGE
First release
v1.01
v1.02
v1.03
08/10/2013
19/08/2019
26/02/2020
Updated Specifications
Corrected the video bandwidth -
Technical Specifications
4
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................7
5. Features..................................................7
6. Operation Controls and Functions.......8
6.1 Transmitter Front and Rear Panels....... 8
6.2 Receiver Front and Rear Panels ............ 9
6.3 D-Sub 9-Pin Definitions.........................10
6.4 IR Cable Pin Assignment .......................10
7. Connection Diagram .......................... 11
8. Specifications...................................... 12
8.1 technical Specifications.........................12
8.2 Cable Specifications ...............................13
9. Acronyms............................................. 14
5
1. INTRODUCTION
The HDMI with RS-232 over Single CAT5e/6/7 transmitter and receiver set
can send uncompressed audio/video over a single run of CAT5e/6/7 cable
up to 100m at 1080p and 70m at 4K and has the added benefit of control
through the built-in RS-232 and IR ports.
Utilise the USB power output from a TV as an optional way of powering
the PU-506-RX receiver unit alternative to a mains power supply.
2. APPLICATIONS
Domestic HDMI installation
University lecturing systems
Retail showroom systems
Conference presentation and control
3. PACKAGE CONTENTS
Transmitter Package
1×HDMI over Single CAT5e/6/7 Transmitter
2×IR Blaster
2×IR Extender
1×3.5 mm Mini-jack to RS-232 Female Cable
1×5V/2.6A DC Power Adaptor
Operation Manual
Receiver Package
1×HDMI over Single CAT5e/6/7 Receiver
2×IR Blaster
2×IR Extender
1×3.5 mm Mini-jack to RS-232 Male Cable
1×5V/2.6A DC Power Adaptor
Operation Manual
6
4. SYSTEM REQUIREMENTS
HDMI source equipment such as a DVD or Blu-ray player and HDMI
equipped display (TV or monitor). HDMI and CAT5e/5/7 connection
cables.
5. FEATURES
HDMI 1.x and DVI 1.0 compliant
HDCP compliant
Supports HDMI 3D and 4K x 2K features
Supports HDCP repeater and CEC function
Supports distance up to 100m/328ft at 1080p and 70m/229ft at 4K
through CAT5e/6/7 cable*
HDMI input resolutions up to 4K@60Hz (YUV 4:2:0, 8-bit) or 4K@30Hz
(YUV 4:4:4, 8-bit)
Supports pass-through of audio formats including LPCM
2.0/5.1/7.1,and Bitstream over HDMI
3Play convergence: HDMI & Control (IR & RS-232)
Installation friendly
Choose to power the PU-506-RX via the USB output from a TV (Cable
available separately - APC-USB) : * Please note the performance and
consistency of USB power outputs from TVs can vary and cannot be
guaranteed by CYP
Note: This system was tested with CAT6/23AWG cable. Results may vary with
cables of different specifications.
7
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
Front
Rear
7
DC 5V
IR2 Extender
HDMI In
Power
Link
RS232 In
IR1 Blaster
CAT 5e/6 Out
1
2
3
4
5
6
8
1
2
3
RS-232 In: Connect to a PC/laptop or RS-232 enabled device(with
supplied 3.5mm phone jack to D-Sub 9 pin adaptor) for the
transmission of RS-232 commands.
IR2 Extender: Connect to the supplied IR extender cable for IR signal
reception. Ensure that remote controller being used is within the
direct line-of-sight of the IR extender.
IR1 Blaster: Connect to the supplied IR blaster cable for IR signal
transmission. Place the IR blaster in direct line-of-sight of the
equipment to be controlled.
4
5
6
7
8
HDMI In: Connect to HDMI source equipment such as a DVD or Blu-
ray player.
DC 5V: Plug the 5V DC power supply into the unit and connect the
adaptor to an AC outlet.
Link: The yellow LED will illuminate when both the input and output
CAT5e/6/7 signals are connected.
Power: This green LED will illuminate when the device is connected to
a power supply.
CAT5e/6 Out: Connect to the receiver unit with a single CAT5e/6/7
cable for transmission of all data signals.
8
6.2 Receiver Front and Rear Panels
Front
Rear
2
DC 5V
IR1 Extender
HDMI Out
Power
Link
RS232 Out
IR2 Blaster
CAT 5e/6 In
1
3
4
5
6
7
8
1
2
3
4
5
DC 5V: Plug the 5V DC power supply into the unit and connect the
adaptor to an AC outlet.
Link: The yellow LED will illuminate when both the input and output
CAT5e/6/7 signals are connected.
Power: This green LED will illuminate when the device is connected to
a power supply.
CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6/7
cable for transmission of all data signals.
RS-232 Out: Connect to the device that is to be controlled (with
the supplied 3.5mm phone jack to D-Sub 9-pin adaptor) by RS-232
commands.
6
7
8
IR1 Extender: Connect to the supplied IR extender cable for IR signal
reception. Ensure that remote being used is within the direct line-of-
sight of the IR extender.
IR2 Blaster: Connect to the supplied IR blaster cable for IR signal
transmission. Place the IR blaster in direct line of sight of the
equipment to be controlled.
HDMI Out: Connect to a HDMI equipped TV/monitor for display of the
HDMI input source signal.
9
6.3 D-Sub 9-Pin Definitions
PIN
1
DEFINE TX/RX
N/C
2
TxD/RxD
RxD/TxD
N/C
3
4
5
GND
6
N/C
7
N/C
8
N/C
9
N/C
6.4 IR Cable Pin Assignment
IR Blaster
1
2
3
Power
IR Blaster Signal
NC
IR Extender
1
IR Signal
Power 5V
Ground
2
3
10
7. CONNECTION DIAGRAM
RS-232 Equipped
PC or Notebook
DVD or Blu-ray Player
HDMI
Input
RS-232
Adaptor
1.5m
60°
7m
3m
3m
60°
IR Blaster
Power
Supply
IR2 Extender
IR Extender
RS232 In
IR1 Blaster
TX
DC 5V
Power
Link
CAut
Single
CAT5e/6/7 Cable
Power
Supply
DC 5V
Power
Link
CAT 5e/6 In
HDMI Out
IR1 Extender
RX
RS23Out
IR2 Blster
IR Blaster
60°
IR Extender
1.5m
RS-232
Adaptor
RS-232 Equipped Device
to be Controlled
60°
3m
HDMI
Output
3m
7m
Display
11
8. SPECIFICATIONS
8.1 technical Specifications
HDMI Bandwidth
HDBaseT Bandwidth
Transmitter
Input
10.2Gbps
10.2Gbps
1×HDMI, 1×IR Extender, 1×RS-232
1×CAT5e/6/7, 1×IR Blaster
Output
Receiver
Input
1×CAT5e/6/7, 1×IR Extender
Output
1×HDMI, 1×RS-232, 1×IR Blaster
IR Frequency
30 – 50kHz (30 – 60kHz under ideal
conditions)
Baud Rate
up to 115200/sec
Power Supply
5V/2.6A DC (US/EU standards, CE/FCC/ UL
certified
ESD Protection
Human-body Model:
8kV (air-gap discharge)
4kV (contact discharge)
IR Frequency
Dimensions
30~50kHz
71mm (W)×79mm (D)×23mm (H)
240g (TX), 245g (RX)
Aluminum
Weight
Chassis Material
Silkscreen Colour
Black
Operating Temperature 0°C~40°C/32°F~104°F
Storage Temperature
Relative Humidity
−20°C ~ 60°C/−4°F~140°F
20~90% RH (non-condensing)
3W (TX), 6W (RX)
Power Consumption
12
8.2 Cable Specifications
1080p
4K30
8-bit
4K60
8-bit
Cable Length
High Speed HDMI Cable
HDMI Input
8-bit 12-bit (4:4:4) (4:2:0)
15m
15m
10m
10m
5m
5m
5m
5m
HDMI Output
Ethernet Cable
Cat.5e/6/7
100m
70m
1080p (FHD Video)
Up to 1080p@60Hz, 12-bit colour
Data rates lower than 5.3Gbps or below 225MHz TMDS clock
-
-
4K30 (UHD Video)
4K@24/25/30Hz & 4K@50/60Hz (4:2:0), 8-bit colour
Data rates higher than 5.3Gbps or above 225MHz TMDS clock but
below 10.2Gbps
-
-
13
9. ACRONYMS
ACRONYM
CAT5e
CAT6
CAT7
CEC
COMPLETE TERM
Category 5 Cable
Category 6 Cable
Category 7 Cable
Consumer Electronics Control
Digital Visual Interface
High-bandwidth Digital Content Protection
High Definition Multimedia Interface
Infrared
DVI
HDCP
HDMI
IR
14
CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton,
Middlesex, TW17 8BA
Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279
Email: [email protected]
v1.03
|