HP f650X User Manual

f650x  
Car Camcorder  
User Manual  
2
About this Guide  
The content in this document is for information purpose and is subject to  
change without prior notice. We have made every effort to ensure that  
this User Guide is accurate and complete.  
However, no liability is assumed for any errors or omissions that may  
have occurred.  
The manufacturer reserves the right to change the technical  
specifications without prior notice.  
Regulatory notices  
This document provides country- and region-specific non-wireless and  
wireless regulatory notices and compliance information for your product.  
Some of these notices may not apply to your product.  
Prohibition of co-location  
This device and its antenna(s) must not be co-located or operated in conjunction  
with any other antenna or transmitter.  
WEEE Notice  
Disposal of Waste Electrical and Electronic Equipment and/or Battery  
by users in private households in the European Union  
This symbol on the product or on the packaging indicates  
that this cannot be disposed of as a household waste. You  
must dispose of your waste equipment and/or battery by  
handling it over to the applicable take-back scheme for the  
recycling of electrical and electronic equipment and/or  
battery. For more information about recycling of this  
equipment and/or battery, please contact your city office,  
the shop where you purchased the equipment or your  
household waste disposal service. The recycling of  
materials will help to conserve natural resources and ensure  
that it is recycled in a manner that protects human health  
and environment.  
3
     
CE Regulatory Notice  
The product herewith complies with the requirements of the Low Voltage  
Directive 2014/35/EU, the EMC Directive 2014/30/EU, the RED-Directive  
2014/53/EU and the RoHS Directive 2011/65/EU.  
EU Health Protection: This equipment should be installed and operated  
with minimum distance 20cm between the radiator & your body.  
Notes on Installation  
1. Please measure the front windshield viewing area, make sure not to  
block driver's front view, install the camcorder below the rearview  
mirror (the central, higher right position of the front windshield). And  
we recommend that the sky and the land occupied by the screen  
50%, fix the car holder and then adjust the camcorder so that the  
lane is aligned with the screen. Proper installation enables the  
camcorder to maximize the efficiency also can enhance the accuracy  
of LDWS.  
2. Make sure that the lens is within the wiping range of the windscreen  
wiper to ensure a clear view even when it rains.  
3. Do not touch the lens with your fingers. Finger grease may be left on  
the lens and will result in unclear videos or pictures. Clean the lens  
on a regular basis.  
4. Do not install the camcorder on a tinted window. Doing so may  
damage the tint film.  
5. Make sure that the installation position is not hindered by the tinted  
window.  
6. This product is suitable for light windshield or light color  
heat-resistant film windows , it will affect video quality if install it on  
the dark windows or dark heat-resistant film windows.  
7. Use the products of the attached power charger only, please do not  
use other brand power charger, in order to avoid equipment burn or  
cause the battery explosion.  
Caution  
Due to local laws and vehicles safety considerations, do not  
operate the camcorder while driving.  
Set up time zone, time and date accurately before you use this  
camcorder.  
Please use SuperCar software under the condition that Electronic  
Map are functioning normally.  
4
     
The firmware function in the camcorder is for reference only,  
drivers are advised to exercise discretion based on actual road  
conditions.  
The results of GPS positioning are only for reference, and should  
not affect the actual driving situation. The camcorder also cannot  
ensure the positioning accuracy.  
GPS positioning accuracy may differ depending on weather and  
location such as high buildings, tunnels, undergrounds, or forests.  
GPS satellite signals cannot pass through solid materials (except  
glass). Tinted window will also affect the performance of the GPS  
satellite reception.  
GPS reception performance on each camcorder may differ. The  
camcorder cannot determine the accuracy of the positioning results  
from different hardware.  
The values displayed in this camcorder, such as speed and  
position, may be inaccurate due to the influence of surrounding  
environment. They are for your reference only.  
This product is used only for non-commercial use, within the  
maximum limits permitted by applicable law. We do not take any  
responsibilities for the loss of use of the product.  
This camcorder gets warm when in use; this is normal.  
Improper use or operation of the product may result in damage of  
the product or its accessories and void the warranty.  
Wi-Fi Signals are unable to pass through the building. The upper  
limit of signal transmission is 5m.  
Wi-Fi Operation Channel: Ch1~Ch13  
The product employs wireless data communication which may  
interfere, or be interfered by, a near-by camcorder.  
Never use this camcorder in the vicinity of a microwave oven or at  
places where there is radio interference.  
Radio wave reception may be worsened in specific environments.  
Please be advised that if another camcorder is also using the same  
2.4GHz band as this product, the processing speed of both  
camcorders may slow down.  
This product gets warm when in use; this is normal.  
Improper use or operation of the product may result in damage of  
the product or its accessories and void the warranty.  
The radio frequency (RF) generated by this RF electronic camcorder  
may cause adverse effects on the operation of other electronic  
5
camcorders and result in malfunctioning. Wireless transmitters and  
circuitry may also interfere with other electronic camcorders.  
Therefore, do observe the following precautions:  
Aircraft: Never use a radio transmitter when you are in an  
airplane. Please switch off the Wi-Fi function of the  
camcorder.  
Vehicle: The radio frequency transmitted by this camcorder  
may affect the electronic system in a motorized vehicle.  
Please consult the manufacturer or dealer of your vehicle on  
the possible effect.  
Pacemaker: In order to prevent any potential interference to a  
pacemaker, anyone who uses a pacemaker should be advised,  
that, when using this camcorder, a minimum distance of 15cm  
(6 inch) should be kept between the camcorder and the  
pacemaker; and never put this camcorder in a chest pocket. In  
case of any doubt of interference, switch off the camcorder  
immediately.  
Medical Camcorder: If you use a personal medical camcorder,  
consult the camcorder manufacturer or your physician to  
confirm if your camcorder is sufficiently shielded from the RF  
transmission of this camcorder.  
Medical Facilities: Hospitals and medical institutes may use  
facilities that are sensitive to an external RF energy. Observe  
such instructions when the medical care personnel or any  
posted sign requests you to switch off any camcorder that  
may interfere the radio frequency.  
Explosion sites or any location with a posted sign: In order to  
prevent interfering with an explosion activity, observe all the  
signage and instructions in the Explosion Area or in a zone  
with a “Switch Off 2-way Radios” sign by switching off  
camcorders that may interfere with the radio frequency.  
HP Inc. is NOT responsible for the loss of any data/content during  
operation.  
Before you start using the system, it is assumed that you  
agree to the above statement.  
6
1 Introduction  
Thank you for purchasing this advanced Car Camcorder. This product is  
specifically designed for real time video recording when driving.  
1.1 Features  
Full HD 1920*1080  
2.0" TFT-LCD color screen  
150° Wide angle lens  
Collision Detection, when a collision is detected, the camcorder will  
automatically trigger the emergency recording  
Parking Mode  
Multifunction traffic safety reminder  
1.2 Package Contents  
The package contains the following items. In case there is any missing or  
damaged item, contact your dealer immediately.  
Electrostatic  
sticker  
Car camcorder  
CD-ROM  
Quick start guide  
Car charger  
7
     
1.3 Product Overview  
No.  
Item  
No.  
Item  
1
2
3
4
5
LED Indicator  
8
9
Speaker  
Wide Angle Lens  
LCD Color Screen  
Menu / Back Button (  
Playback / Up Button (  
Snapshot / Down Button (  
/
)
10 Microphone  
/
)
11 Power Button  
12 Power Connector Port  
13 Memory Card Slot  
14 Bracket Knob  
/
)
Emergency Recording / Confirm  
Button (  
6
/
)
7
Voice Record on/off (  
)
Note:  
Please press the button (3~7) according to the diagram notice shown on screen.  
8
 
2 Getting Started  
2.1 Storage Media  
2.1.1 Insert the Memory Card  
Insert memory card with the pins facing forward and the screen of the  
camcorder facing forward too, see the picture as below:  
2.1.2 Remove the Memory Card  
If the camcorder is power on, please power off first and wait for the  
procedure of switching off the camcorder completed before removing  
the memory card.  
Note:  
1. Do not remove or insert the memory card when the camcorder is turned on. This may damage the  
memory card.  
2. Support SDHC class 10 and memory storage 8GB or above (support up to 32GB).  
3. Please format the micro SD cards before the initial use. The formatted file type for this camcorder  
is FAT32 file.  
4. Periodically format the microSD card (recommended period: once a month).  
9
       
2.2 Installing in Vehicles  
2.2.1 Mount to Windshield  
1.  
Put the electrostatic sticker onto the suggested area on the  
windshield. Before putting the sticker, please wipe and clean the  
windshield. During the installation, please make sure the bubbles  
in between the sticker and the window are all gone.  
2.  
Peel off the protective plastic sheet from the adhesive pad.  
10  
   
3.  
Place and press the bracket firmly onto the electrostatic sticker on  
the windshield window. Make sure the base is securely locked in  
place.  
2.2.2 Adjust the Camcorder  
1. Loosen the knob to swivel the camcorder to adjust view angle.  
2. Then tighten the knob to make sure the camcorder is securely  
locked in place.  
11  
 
2.3 Connecting to Power  
Use only the supplied car charger to power up the camcorder.  
1. Connect one end of the car charger to the USB connector of the  
camcorder. USB port input: DC 5V / 1A.  
2. Plug the other end of the car charger to the cigarette lighter socket  
of your vehicle. Once the vehicle engine is started, the camcorder  
automatically powers on. Car charger input: DC 12 / 24V.  
2.4 LED Indicator  
Status Explanation  
LED Indicator Color  
Red  
Power off, connect  
external power  
Power on, standby  
Green  
Recording/ Recording  
and screen off  
Flash red  
12  
   
2.5 Powering the Camcorder On / Off  
2.5.1 Auto Power On/Off  
Start the car engine, wait a few seconds to charge the camcorder, and  
then screen will light up and the camcorder will automatically power on  
and start recording.  
Once the vehicle engine shuts down, the camcorder automatically saves  
the recording and turns off the power.  
2.5.2 Manual Power On/Off  
To manually turn on the power, press the POWER button.  
To turn off, press and hold the POWER button for at least 2 seconds.  
2.5.3 Reset  
Press and hold the Power button for 8 seconds to reset the device.  
13  
       
2.6 Initial Settings  
Before using the camcorder, we recommend you setup the correct Time  
zone, Date and Time.  
Note:  
Please note that if you press the  
button during recording, the system will stop recording and  
enter OSD menu. Make sure the recording is already stopped then continue operating the menu.  
2.6.1 Set Time Zone  
To set the time zone, do the following:  
1. Press the  
button to enter the OSD menu.  
2. Press the  
or  
button to select Set Time Zone, and then  
press the  
button for entering function menu.  
3. Press the  
or  
button to set the current time zone, and  
button to complete setting.  
button to return to recording screen.  
then press the  
4. Press the  
Note:  
1. If Time Sync. is on, camcorder clock will be calibrated via satellite clock signal based on Set Time  
zone.  
2. If satellite positioning is not successful, camcorder clock will run based on user defined time.  
14  
   
2.6.2 Set the Date / Time  
To set the correct date and time, do the following:  
1. Press the  
button to  
enter the OSD menu.  
2. Press the  
or  
button to select Date / Time,  
and then press the  
button for entering function  
menu.  
3. Press the  
or  
button to adjust the value, and then press the  
the next field.  
button to set  
4. Repeat step 3 until the date and time setting is completed.  
Note:  
To ensure the accuracy of the video file time, please reset the date and time when not in use over 7  
days.  
15  
 
3 Using the Car Camcorder  
3.1 Automatic Record  
Start the car engine, wait a few seconds to charge the camcorder, and  
then screen will light up and the camcorder will automatically power on  
and start recording.  
Recording will automatically stop when the engine is switched off.  
Note:  
1. Some vehicle power supply would not turn on / off automatically with the car engine start, if the  
camcorder cannot automatically power on/off with the car engine, please manually connect the  
power supply with the vehicle power, and then power on, or manually power off the camcorder and  
then release the connector with the car power supply.  
2. It can be configured to save a video file for every 30 seconds, 1 or 3 minutes of recording.  
3. All the videos and photos are saved in the memory card, if memory card is full, loop recording will  
generally overwrite the oldest video file.  
4. The camcorder is built-in super capacitor. After start the car engine, please wait a few seconds for  
charging the camcorder, and then the camcorder will automatically power on and start recording.  
16  
   
3.1.1 The Recording Screen  
No.  
Icon  
Item  
Description  
1
Recording Duration  
Indicates the video current duration.  
Indicates the current recording date  
and time.  
2
3
Date / Time  
During video recording, press the  
button to enter the OSD menu.  
Menu Button  
During video recording, press the  
button to add a speed cam  
point.  
Add Speed Point  
Button  
4
5
PIV (Picture in  
Video) Button  
Press  
to capture video screen  
shots from the front camera.  
During video recording, press the  
button to enter emergency  
recording mode.  
Emergency  
Recording Button  
6
17  
 
7
8
Voice Record on/off Turn on/off voice recording.  
Resolution  
Indicates the video resolution.  
icon  
Voice Record  
icon  
Indicates voice recording sets as off,  
the sound will not be recorded.  
9
Indicates the strength of satellite  
positioning. If the icon shows in red  
on screen, it indicates that the  
camcorder cannot complete the  
satellite positioning.  
Satellite Positioning  
icon  
10  
Indicates camcorder is connected  
with power.  
11  
12  
Power icon  
Wi-Fi  
Wi-Fi on  
Wi-Fi off  
18  
3.1.2 Emergency Recording  
To Start the Emergency Recording, do the following:  
1. During Video Recording, press  
the  
button to enter  
emergency recording mode,  
the “Emergency” message  
will be shown immediately on  
the upper left corner of the  
screen, and the recorded file  
will be protected.  
2. The emergency video  
recording length is same as the recording interval setting. When the  
emergency recording length reaches the setting, the system will  
return to the general recording mode.  
Note:  
1. If the Collision Detection function is enabled and a collision is detected, the camcorder will  
automatically trigger the emergency recording.  
2. The emergency file is created as a new file and saved in Emergency folder, which will be protected  
to avoid being overwritten by normal loop recording. The Emergency folder will occupy 40% of  
available memory card capacity. For example, if you use 8GB memory card, about 3.2GB memory  
space will be saved for emergency files. When the Emergency folder is full, the oldest emergency file  
will be automatically deleted by the newest emergency file.  
3.2 Add Speed Point  
You may customize speed cam positions in this product.  
1. When the GPS positioning is completed , press  
camera points.  
to update speed  
2. This product features a capacity of 50 speed cam positions. In case  
you are trying to add more than that, the system prompts with  
message "Speed Position is full".  
Note:  
You may delete custom speed cam positions by selecting the Delete Last Position or Delete All  
Position option from the Speed Position Management menu. Please note that all of your existing  
speed cam positions are deleted once the Delete All Position option is selected. Make sure you are  
ready to recreate your custom speed cam positions before running this option.  
19  
   
3.3 Picture in Video  
You can also use this camcorder to take snapshots of the current scene.  
1. In recording status, press  
to capture recording  
screen shots from the front  
(and rear) lens.  
2. When the icon  
shows  
in the central of screen, it  
means the screenshots is  
completed.  
Note:  
1. The screen shots image resolution quality is depending on the video resolution setting.  
2. The picture resolution is limited by the speed of the target object and changes in ambient lighting.  
The photograph function is better used for taking still pictures in accident scenes or when the car is  
stopped to wait for a traffic light.  
3.4 Driving Safety  
The following driving safety function is for reference only. Drivers are advised  
to exercise discretion based on actual road conditions.  
Note:  
1. The Driving Safety function is limited to triggering no more than two alarms at the same time. If a  
voice and alert message have been triggered, any other alarm will be ignored until either of the two is  
settled.  
2. Satellite positioning must be completed before functions such as Speed Cam Alert, Speed Position  
Management, Speed Limit Alert, LDWS, FCWS and FCMD to be enabled. Be sure to check that Satellite  
positioning has been completed prior to using the product.  
3. The detections of LDWS, FCWS and FCMD may be inaccurate when used in rain, at night or in  
environments of insufficient lighting. Drivers are advised to exercise discretion based on actual road  
conditions.  
20  
   
3.4.1 Speed Cam Alert  
If the Speed Cam Alert function is enabled, once your car’s location is  
determined by GPS and approaches a speed cam, this product produces  
audible alert and screen message.  
To enable the Speed Cam Alert, do the following:  
1. Press the  
enter the OSD menu.  
2. Press the  
button to  
/
button  
to select Speed Cam Alert,  
and then press the  
button for entering function  
menu.  
3. Press the  
/
button  
to select On, and then press  
the  
button to enable the function.  
button to return recording screen.  
4. Press the  
5. The alarm screen turns red to remind you to slow down if you are  
driving faster than the speed limit.  
Note:  
The speed cam alert function must have the speed cam datum from the country you use. The function  
will be void if the product is used in any other countries. Please consult with the shop you purchased if  
the function is void. There is no guarantee the speed cam datum will be included for the worldwide  
countries.  
21  
 
3.4.2 Speed Limit Alert  
If the Speed Limit Alert function is enabled, this product produces  
audible alert and screen message once your car’s location is determined  
by GPS and its running speed exceeds the set limit.  
To set the Speed Limit Alert, do the following:  
1. Press the  
button to  
enter the OSD menu.  
2. Press the  
/ button to  
select Speed Limit Alert,  
and then press the  
button for entering function  
menu.  
3. Press the  
/
button  
to set up a Speed Limit Alert  
to trigger this product’s alarm [Off / 50 ~ 200 km/h (30~125 mph)],  
and then press the  
4. Press the  
button to complete setting.  
button to return recording screen.  
5. The screen pops up red icon to remind you to slow down when you  
are driving faster than the set speed limit.  
22  
 
3.4.3 Driver Fatigue Alert  
If the Driver Fatigue Alert function is enabled, this product produces  
audible alert and screen message one hour after it has begun recording  
and repeats the alerts every half hour afterwards.  
To enable the Driver Fatigue Alert, do the following:  
1. Press the  
2. Press the  
then press the  
3. Press the  
button to enter the OSD menu.  
/
/
button to select Driver Fatigue Alert, and  
button for entering function menu.  
button to select On, and then press the  
button to enable the function.  
4. Press the button return to recording screen.  
5. This product produces audible alert and screen message when  
Driver Fatigue Alert activates.  
3.4.4 LDWS  
Once your car’s location is determined by GPS and the LDWS function is  
enabled, this camcorder produces audible alert and screen message  
when you drive off of or change lanes at speeds over 70 km/h (43 mph).  
To set the LDWS (Lane Departure Warning Systems), do the following:  
1. Press the  
2. Press the  
button to enter the OSD menu.  
/
button to select LDWS, and then press the  
button for entering function menu.  
3. Press the  
/
button to select On, and then press the  
button to enable the function.  
4. Press the  
button to return to recording screen.  
23  
   
5. After enabling LDWS, the screen will display traffic lane align icon  
, please adjust the camcorder so that the horizontal line and  
the eye level are overlapped and the slash lines are centered in the  
driving lane.  
6. This product produces audible alert and screen message when  
LDWS is activates.  
Note:  
1. Please measure front windshield viewing area, do not block the driver's forward field of vision, and  
install the camcorder below rearview mirror (upper central of the front windshield). We recommend  
that the sky and the ground occupied 50 % of the video screen, install the bracket then adjust the  
camcorder to make the lane is aligned to the lane alignment icon. Correct installation makes the  
camcorder to maximize the efficiency and improve the accuracy of LDWS.  
2. Make sure that traffic lane align icon will not be obscured other things (e.g. hood). It may cause  
misjudgment if the endpoint is obscured.  
24  
3.4.5 FCWS  
Once your car’s location is determined by GPS and the FCWS function is  
enabled, this camcorder produces audible alert and screen message  
when you drive at speeds over 60 km/h (37 mph) and are less than 20 m  
away from the car in front of you. If the camcorder not completes the  
satellite positioning, and the leading vehicle distance below 20 meters, it  
will also produce a warning screen and beep reminder.  
To set the FCWS (Forward Collision Warning System), do the following:  
1. Press the  
2. Press the  
button to enter the OSD menu.  
/
button to select FCWS, and then press the  
button for entering function menu.  
3. Press the  
/
button to select On, and then press the  
button to enable the function.  
4. Press the  
button to return recording screen.  
5. This product produces audible alert and screen message when  
FCWS is activates.  
25  
 
3.4.6 Headlight Warning  
The Headlight Warning function produces audible alert and screen  
message when it detects poor lighting conditions through the recording  
displays of this camcorder, including driving in rainy or cloudy weather,  
at night, and in basements, parking lots, and tunnels.  
To enable the Headlight Warning, do the following:  
1. Press the  
button to enter the OSD menu.  
2. Press the  
press the  
/
/
button to select Headlight Warning, and then  
button for entering function menu.  
3. Press the  
button to select On, and then press the  
button to enable the function.  
4. Press the button to return recording screen.  
5. This product produces audible alert and screen message when  
Headlight Warning activates.  
26  
 
3.4.7 FCMD  
If FCMD function is enabled, when the front car moves and you don’t start  
to drive forward, the camcorder will issue audible alert and screen  
message.  
To set the FCMD (Front Car Move Detection), do the following:  
1. Press the  
2. Press the  
button to enter the OSD menu.  
/
button to select FCMD, and then press the  
button for entering function menu.  
3. Press the  
/
button to select On, and then press the  
button to enable the function.  
4. Press the  
button to return recording screen.  
5. This product produces audible alert and screen message when  
FCMD activates.  
Note:  
The camcorder will detects the front image change to determine FCMD notification alert, so if the car  
is in rest condition and front object moves, the camcorder may occur false judgment, and please  
judge it according to the actual driving situation.  
27  
3.5 Parking Mode  
To monitor the vehicle when it is parked, you can activate Park Recording,  
or Motion and Collision Detection, or Timelapse.  
Before you activate Parking Mode, please install ACC cable through  
professional car service shop.  
Follow the steps below to change the settings for Parking Mode:  
1. Press the  
2. Press the  
press the  
button to enter the OSD menu.  
/
button to select Parking Mode, and then  
button for entering function menu.  
button to configure Parking Mode (Park  
3. Press the  
/
Recording / Motion and Collision Detection / Timelapse/ Off), and  
then press the  
4. Press the  
button to complete setting.  
button to return recording screen.  
Note: ACC cable is not included in the package. Please ask for more information from your  
distributor.  
3.5.1 Park Recording  
-
In normal recording, press and hold POWER key for 3 seconds, the  
screen will show message “Press OK key to power off or enter  
Park Recording after 10 sec.Please wait for 10 seconds and the  
camcorder will enter Park Recording automatically. The  
camcorder will turn off the screen temporarily, but still in  
recording status. Once the collision or vibration is detected, it will  
automatically trigger emergency recording.  
-
To disable this function, press any key to wake up the screen, and  
press again any key to resume to normal loop recording.  
Note:  
1. The video file taken in this mode is same as normal loop recording mode. It will be saved in the  
“Video” folder. And the emergency file will be saved in the “Emergency” folder.  
2. The file size is according to Record Interval setting.  
28  
3.5.2 Motion and Collision Detection  
-
In normal loop recording mode, press and hold POWER key for 3  
seconds, the screen will show message “Press OK to power off or  
enter Motion and Collision Detection after 10 sec.” Please wait  
for 10 seconds and the camcorder will enter Motion and Collision  
Detection automatically. The camcorder will turn off the screen  
temporarily, but still in standby detection status. When the  
camcorder detects any motion in front of lens or any  
vibration/collision, the video recording will be triggered and the  
event will be recorded.  
To disable this function, press any key to wake up the screen, and  
press again any key to resume to normal loop recording.  
-
Note:  
1. The video file taken in this mode will be saved in the “Emergency” folder.  
2. In this mode, the event will be recorded for 10 seconds (per file). If the event lasts more than  
10 seconds, the camcorder will keep recording up to 2 minutes.  
3.5.3 Timelapse  
-
In normal loop recording mode, press and hold POWER key for 3  
seconds, the screen will show message “Press OK to power off or  
enter Timelapse after 10 sec.” . Please wait for 10 seconds and  
the camcorder will enter Timelapse automatically. The camcorder  
will turn off the screen temporarily, but in timelapse recording  
status.  
-
To disable this function, press any key to wake up the screen, and  
press again any key to resume to normal loop recording.  
Note:  
1. The video file taken in this mode will be saved in the “Video” folder.  
2. In this mode, the camcorder is continuously recording by one second one frame. For example,  
30 minutes recording will be saved in one minute.  
3. The file size is according to Record Interval setting.  
29  
3.6 Collision Detection  
If the Collision Detection function is enabled, this camcorder begins  
emergency recording once it detects any collision. Sensitivity of the  
Collision Detection function is set to Normal by default, if user wants to  
change the settings of Collision Detection, do the following:  
1. Press the  
2. Press the  
then press the  
3. Press the  
button to enter the OSD menu.  
/
/
button to select Collision Detection, and  
button for entering function menu.  
button to change the sensitivity of this  
camcorder’s collision detection (High Sensitivity / Normal  
Sensitivity / Low Sensitivity / Off), and then press the  
button for entering function menu.  
4. Press the  
button return to recording screen.  
30  
3.7 Playback Videos and Photos  
1. If recording is in progress,  
/
press the  
button to stop recording and  
enter Menu.  
2. Press the  
or  
button to select Playback and  
press the  
button.  
3. Press the  
or  
button to select Video, Emergency or Picture category and press  
the  
button.  
4. Use the  
or  
to select the video or photo you want to  
button to confirm your selection.  
playback, and press  
31  
 
3.8 The Playback Screen  
No.  
Item  
Description  
1
File name  
File name  
Duration/ Total Indicates the video elapse time/ Indicates total recorded  
2
3
recorded time  
time  
Press the  
video or picture. Press the  
button to return preview screen of  
Return  
button repetitively to  
return recording screen.  
Previous File  
Button  
4
5
6
Press  
button to view previous file.  
button to view next file.  
button to play or pause the video.  
Next File Button Press  
Playback/ Pause  
button  
Stamp print  
File  
Press the  
7
8
Indicates date and time stamp  
Current file / total file number  
32  
 
3.9 Deleting Files  
To delete file(s), perform the following steps:  
1. Press the  
button to stop recording and enter the main Menu.  
or button to select File Deletion and  
button to confirm.  
2. Press the  
press the  
3. Press the  
or  
button to select folder and press the  
button to confirm. The following options will display in  
screen,  
Item  
Delete One  
Delete All  
Description  
Delete the current selected file.  
Deletes all files in this folder.  
4. Use the  
or  
to select the video or photo you want to  
button to confirm your selection.  
delete, and press  
Note:  
Deleted files CANNOT be recovered. Ensure the files you wish to preserve are backup before deletion.  
33  
 
4 Initial set up Go Dashcam application  
4.1 Camcorder application installation  
The camcorder allows you to connect to the mobile devices via the App.  
When using for the first time, install the [Go Dashcam] App for your  
mobile device.  
1. Download Go Dashcam App  
from Google Play or App Store.  
2. Install the App.  
APP layout and features may be changed subject to different  
software versions. Please refer to Google Play or APP Store  
for update.  
34  
 
4.2 Wi-Fi connecting  
1. Press the Power button to switch on the camcorder.  
2. Enter Menu and go to Wi-Fi option; choose “ON” to activate the  
wireless network.  
3. The camcorder’s screen will display Wi-Fi Device ID and Password.  
Using the Wi-Fi function of your mobile device, search for the  
camcorder ID “hp_f650x_123456” from the list (last 6 numbers are  
system random numbers). Enter default password 12345678.  
4. There is a Wi-Fi icon on the camcorder’s screen. Once the icon is  
blue, your connection has been successfully established.  
Note:  
1. The mobile device shall be within a maximum of a 5m distance from the camcorder without any  
buildings in between.  
2. When the Wi-Fi function of the camcorder is ON but not yet connecting with your mobile device, or  
the connection is disconnected, the Wi-Fi icon on camcorder’s screen will be white, and you will  
need to re-activate the Wi-Fi and re-pair with your mobile device.  
3. After connecting the mobile device with the camcorder, and activate app feature “Camera  
Preview”, all the button operation of the camcorder will be disable; all the operations shall be  
carried out via the Go Dashcam App.  
4. The language of the Go Dashcam App will be consistent with your mobile device, beyond the  
language options, the App will be activated with default language.  
35  
5 Using the Go Dashcam application  
Touch [Go Dashcam]  
icon to activate the application. The  
main screen will pop up. Follow the below instruction to operate  
this application.  
36  
   
5.1 Camera preview, record, snapshot  
You can use this feature to preview, record or take snapshot.  
1. The mobile device will display camcorder’s preview screen. The  
camcorder will lose control and screen will show ”Network Streaming”.  
Please use Go Dashcam app to operate the camcorder.  
icon  
Description  
1
2
Start/stop recording.  
Snapshot.  
3
Not available for this model.  
37  
5.2 Playback, delete, download  
You can use this feature to playback or delete the file saved in camcorder,  
or to download the file from camcorder to your mobile device.  
1. Touch the icon  
playback].  
[Video playback] or  
[Picture  
2. The files saved in the camcorder will be displayed on your mobile  
device. Camcorder will stop recording for a few seconds until your  
mobile device finishes reading the saved files from camcorder, and  
screen will show ”Network Playback”.  
3. Touch the preview image of video or picture to playback.  
4. Touch the right top corner “Select” and pick up the files that you  
want to delete or download, and touch below icon to execute.  
38  
 
Icon  
Description  
1
Not available for this model.  
Download the file from camcorder to your mobile  
device  
2
3
Delete  
Exit  
4
Note:  
1. If you find the video playback without audio, please check if you turn on Voice Record on the menu.  
If you do turn it on, it means the mobile device itself doesn’t support the video decoding. It’s not the  
problem of the file. We recommend you to install a free app software such as VLC to playback the  
file.  
2. Deleted files cannot be recovered. Ensure the files have been backed-up before deletion.  
3. Picture and video files could be downloaded to the internal memory of your mobile device. Use the  
application program in your mobile device to view the file.  
4. The downloaded videos or pictures will be saved in the album of your mobile device, at the mean  
time it will create a new folder “Go Dashcam”. You can preview the files from the album.  
39  
 
5.3 Local album  
You can use this feature to playback or delete the file that you download  
to your mobile device.  
1. Touch icon  
[Local Album]  
2. Pick up the file that you want to playback.  
3. The downloaded videos or pictures will be saved in the album of your  
mobile device, at the mean time it will create a new folder “Go  
Dashcam”. You can preview or delete the files from the album.  
Note:  
1. Deleted files cannot be recovered. Ensure the files have been backed-up before deletion.  
2. If you find the downloaded files could not be played or without audio, which means the mobile  
device itself does not support the video decoding. It’s not the problem of the file. We recommend  
you to install a free App software such as VLC to playback the file.  
40  
5.4 Camera Setting  
You can use this feature to set up your car camcorder.  
1. Touch icon  
[Camera Setting].  
2. Refer to the below table for details of menu items and available  
menu options.  
Menu option  
Description  
Available option  
1080p 30fps HDR  
Set the desired video  
resolution.  
Resolution  
720p 30fps HDR  
Save respective video files  
in a length of the selected  
duration.  
Record Interval  
Voice Record  
30 sec / 1 min / 3 min  
Setting for activating audio  
in the video.  
On / Off  
On / Off  
If the time stamp is  
enabled, recording files or  
photos will show the date  
and time.  
Time Stamp  
Return to factory default  
setting.  
Default  
Format  
Yes / No  
Yes / No  
To format the memory  
card, all the files in the  
camcorder will be deleted.  
WiFi Setting  
To set up Wi-Fi password  
Indicates the current car  
Firmware Version camcorder’s firmware  
version.  
Indicates the current  
App Version  
application version.  
41  
 
6 Adjusting the Settings  
6.1 Using the Menu  
You can customize the general settings via the on-screen display (OSD)  
menus.  
1. Press the  
2. Press the  
the  
3. Press the  
press the  
button to enter the OSD menu.  
/
button to select menu item, and then press  
button for entering function menu.  
button to select or adjust the value, and then  
/
button to confirm setting.  
4. Press the  
button to return recording screen.  
6.2 Menu Items  
Refer to the below table for details of main menu and function list.  
Menu option  
Description  
Available option  
Video  
Emergency  
Picture  
Select the file category that  
you want to view.  
Playback  
Set up Wi-Fi linkage of a  
mobile phone.  
Wi-Fi  
On / Off  
Displays the current state of  
the satellite reception.  
Satellite Status  
If the satellite time is enabled,  
the car camcorder clock will  
synchronize according to the  
satellite time zone you set.  
When you turn on this  
feature, it will display the  
satellite time preferentially,  
and cannot be manually  
changed.  
Satellite  
Synchronization  
On / Off  
The system displays the  
speed setting unit.  
Speed Unit  
KM/H / MPH  
42  
     
Menu option  
Description  
Available option  
If the Speed Cam Alert  
function is enabled, once your  
car’s location is determined  
by GPS and approaches a  
speed cam, this product  
produces audible alert and  
screen message.  
Speed Cam Alert  
On / Off  
Add Speed Point: The  
satellite positioning will  
manually add speed camera  
location. You can add up to 50  
speed camera locations to the Add Speed Point / Delete  
Speed Position  
Management  
built-in system.  
Last Position / Delete All  
Position  
Delete Last Position: Delete  
the last speed camera point.  
Delete All Position:  
Delete all speed camera  
point.  
Set a customized maximum  
speed limit. When the vehicle  
speed exceeds the maximum,  
an audible alert is  
automatically triggered and a  
warning message is displayed  
on the screen.  
Press the  
/
button to  
set the speed limit. You can  
set the off, or set speed limit  
from 50 to 200km/h (30 to  
125mph)  
Speed Limit Alert  
Press the  
/
button to  
set the satellite time. You  
may customize it between  
GMT -12:00 ~ GMT +14:00  
Set Time Zone  
Date / Time  
Set the time zone you are in.  
Press the  
adjust the value, and then  
press the button to  
/
button to  
Set the date and time.  
Language setting.  
set the next field, and  
complete setting  
According to the actual  
shipping regions.  
Language  
If the time stamp is enabled,  
recording files or photos will  
show the date and time.  
Time Stamp  
On / Off  
1920x1080 30fps HDR  
1280x720 30fps HDR  
Resolution  
Setting of video resolution.  
43  
Menu option  
Description  
Available option  
Press the  
/
button to  
EV  
Setting of exposure value.  
set the exposure value. It can  
be set between -2 ~ +2  
Set LCD off time. Camcorder  
screen will be off after a set  
time if no operation is  
detected during the standby  
or record mode. Press any  
button will switch it on.  
(Recording is not affected  
when screen is off).  
On/ Turn off after 7 sec /  
Turn off after 1min/ Turn off  
after 3min  
LCD Setting  
Setting for activating audio in  
the video.  
Enable / disable power-on  
sound and key tone.  
Voice Record  
Key Tone  
On / Off  
On / Off  
Press the  
set the volume. It can be set  
between 0 ~ 10.  
/
button to  
Volume  
Adjust the sound volume.  
Save respective video files in  
a length of the selected  
duration.  
Record Interval  
30 sec. / 1 min. / 3 min.  
If one of parking mode is  
activated, the camcorder will  
enter parking mode 10  
seconds after disconnect the  
external power.  
Off/ Park Recording / Motion  
and Collision Detection /  
Timelapse  
Parking Mode  
If Collision Detection is  
High Sensitivity / Normal  
Sensitivity / Low Sensitivity /  
Off  
activated, this camcorder  
starts emergency recording  
once it detects any collision.  
Collision Detection  
When Driver Fatigue Alert is  
enabled, audible alert and  
screen message will be  
activated 1 hour after the  
camcorder is powered on,  
with a repetition every 30  
minutes.  
Driver Fatigue Alert  
On / Off  
44  
Menu option  
Description  
Available option  
When Headlight Warning is  
activated, camcorder will  
issue an audible alert and  
screen message reminding  
that insufficient brightness is  
sensed on the recording face.  
Headlight Warning  
On / Off  
Once your car’s location is  
determined by GPS and the  
LDWS function is enabled, this  
camcorder produces audible  
alert and screen message  
when you drive off of or  
change lanes at speeds over  
70 km/h (43 mph).  
LDWS  
FCWS  
On / Off  
When FCWS is activated after  
satellite positioning,  
camcorder will issue audible  
alert and screen message  
when vehicle speed is above  
60 km/h (37 mph) and the  
distance with the front vehicle  
is less than 20m.  
On / Off  
If FCMD function is enabled,  
when the front car moves and  
you don’t start to drive  
forward, the camcorder will  
issue audible alert and screen  
message.  
FCMD  
On / Off  
Video  
File Deletion  
Anti-flicker  
Delete the file(s).  
Emergency  
Picture  
Domestic power supply varies  
by area. It is recommended  
that you should check the  
“Table of voltage and  
frequency of different  
countries” for the correct  
setting.  
60Hz / 50Hz  
45  
Menu option  
Description  
Available option  
Format the memory card  
inserted in the equipment. All  
the files in the card will be  
erased.  
Format  
Yes / No  
The system reverts to the  
default setting.  
Default  
Yes / No  
Indicates the current  
firmware version.  
Firmware Version  
46  
7 Installing the Software  
1. Place the attached CD ROM into the CD player.  
2. If the CD does not execute automatically, please use Windows File  
Manager to execute the Install_CD.exe file in the CD.  
The following screen will be shown up.  
3. Press the [Menu] item to start the installation process according to  
the instructions on-screen.  
47  
 
8 SuperCar  
7
8
9
10  
11  
1
12  
13  
14  
15  
2
3
4
5
16  
6
No.  
Item  
Video Player  
No.  
Item  
1
2
3
4
5
9
File Path  
Play / Pause  
Previous  
Next  
10  
11  
12  
13  
Browser File  
File List  
File Name  
Volume  
Stop  
Playback Duration / Total  
Duration  
6
Electronic Map  
14  
7
8
Compass  
15  
16  
Signal Noise Ratio (SNR)  
G-Sensor  
Speed Meter  
Note:  
1. To display the route on Electronic Map, please make sure the internet is connected before starting  
the video playback.  
2. Video files of front-view camera (MOV) and GPS/G-Sensor files (NMEA) must be stored in the same  
folder before starting the playback.  
3. The SuperCar software is only applicable to Windows operating system. For Mac users, please  
search “SuperCar”  
App in built-in Mac App Store.  
48  
 
9
Specifications  
Item  
Description  
Image sensor  
Effective pixels  
Storage media  
LCD display  
1/2.7CMOS sensor  
1920 (H) x 1080 (V)  
Supports Micro SDHC, up to 32GB class 10 speed or greater  
2” LCD color TFT  
Wide Angle Fixed Focus lens  
Aperture: Up to F2.2  
Lens  
Focus range  
1.5m~Infinity  
Satellite System GPS  
Resolution: 1080P/ 30 fps 720P/ 30 fps  
Video  
Format: MOV  
Resolution: depends on video resolution setting  
Still image  
(Photograph)  
Format: DCF (JPG)  
Electronic shutter  
3-Axis G-Force sensor  
Auto  
Shutter  
G-Sensor  
ISO  
White Balance  
Microphone  
Speaker  
Auto  
Built-in  
Built-in  
Interface  
Mini USB  
Power  
Super Capacitor  
49  
 
Item  
Description  
Operating  
Temperature  
0° ~ 45° C  
Operating Humidity 20 ~ 70% RH  
Storage  
-20° ~ 70° C  
Temperature  
Dimensions  
Weight  
58 x 43.5 x 45.3 mm  
Approx. 82g  
Built-in IEEE 802.11b/g/n(HT20) Wi-Fi chip: RTL8188FTV  
Frequency range  
Wi-Fi Channel  
2412~2472MHz  
Ch1~Ch13  
18dBm  
Wi-Fi Max. output  
50  

Schumacher 1010 2 Pe User Manual
Sanyo Ks0951 User Manual
Sanyo Cr1304gdzh8 User Manual
Samsung Us07s8ge User Manual
NEC NP PH1000U 02 User Manual
LG LWJ0514ACG User Manual
LEVOIT CORE 200S User Manual
CRAFTSMAN 917.274350 User Manual
CRAFTSMAN 138.98981 User Manual
ASUS VC239N 02 User Manual