Radio / Cassette / Changer
Coburg RCM 127
Casablanca RCM 127
Cannes RCM 127
Woodstock DJ I
Woodstock DJ A
Operating instructions
Contents
Quick reference ............................ 28
Scrolling through the broadcasting
Adjusting the volume for traffic
networks................................................ 37 announcements and the beep tone...... 43
Important notes ............................ 33
Changing the memory bank ................. 37
Tape operation ............................. 43
Storing stations ..................................... 37
Precautions ........................................... 33
Traffic safety ......................................... 33
Installation............................................. 33
Sound source mute .............................. 33
Accessories .......................................... 33
Inserting a tape ..................................... 43
Automatically storing the strongest
Removing a tape................................... 43
stations with Travelstore....................... 38
Fast Forward/Rewind ........................... 43
Recalling stored stations ...................... 38
Selecting titles with CPS ...................... 43
Scanning stored stations with
Switching the tape side (autoreverse).. 44
Preset Scan .......................................... 38
KeyCard theft protection system 34
Tape equalisation ................................. 44
Scanning cassette titles with SCAN ..... 44
Listening to the radio during
fast tape winding with RM .................... 44
Care notes ............................................ 44
Scanning stations with Radio-Scan...... 38
Putting the unit into operation .............. 34
Removing the KeyCard ........................ 34
“Training” a second KeyCard/
Replacing a KeyCard............................ 34
Displaying the radio pass data ............. 34
Short Additional Memory (S.A.M.)........ 35
Turn On Message (T.O.M.) .................. 35
Optical indication of anti-theft
Selecting the seek tuning sensitivity .... 39
Switching from stereo to mono............. 39
Loudness .............................................. 39
PTY – Programme-Type....................... 39
Switching PTY on/off ......................... 39
Programme type ................................... 39
Checking the programme type of the
station ................................................ 40
Displaying the selected programme
type .................................................... 40
Selecting a programme type ............. 40
Storing programme types.................. 41
Scanning stations with PTY-SCAN ... 41
PTY priority........................................ 41
CD changer operation.................. 45
Switching to the CD changer mode...... 45
Selecting CDs and titles ....................... 45
MIX playback ........................................ 45
Selecting the display mode .................. 46
SCAN .................................................... 46
protection .............................................. 35
Care of your KeyCard ........................... 35
Switching the audio source ........ 35
DSC programming ....................... 47
Radio operation with RDS ........... 36
Overview of DSC factory settings ........ 49
AF - Alternative frequency .................... 36
REG - regional programme .................. 36
Selecting a waveband
(only Casablanca RCM 127,
Cannes RCM 127, Woodstock DJ A) ... 36
Station tuning ........................................ 37
Appendix ....................................... 49
Receiving traffic programme
stations with RDS-EON................ 42
Specifications........................................ 49
Blaupunkt telephone hotline ................. 49
Traffic announcement priority on/off .... 42
Beep tone ............................................. 42
Switching off the beep tone............... 42
Automatic seek tuning start .................. 42
Automatic tuning
/
....................... 37
Manual tuning with << >>.................. 37
27
Quick reference
Switching on/off via the ignition:
When connected correspondingly, the
set can also be turned on and off with
the vehicle ignition.
After the ignition has been switched
off, a double beep tone will remind you
that you should remove the KeyCard
before leaving your vehicle.
3
1 Switching on/off with the ON button:
Press ON.
For instantly muting the volume.
By pressing the
button the volume
When switching the set on with the ON
button, the KeyCard has to be insert-
ed. The unit will play with the pre-ad-
justed volume.
can be muted immediately. “MUTE”
will appear in the display.
The function is cancelled by pressing
button
or VOL+.
When pressing VOL-, the
(mute)
volume will be adopted.
Switching on with the ignition being
switched off:
To programme the mute volume level,
proceed as follows:
To keep on operating the set when the
ignition is switched off (KeyCard is in-
serted), proceed as follows:
Press ON. The unit will be turned on.
To avoid that the battery goes flat, the
system will be turned off automatically
after one hour of playback.
•
•
Adjust the desired volume.
Press for 1 second until you
hear a beep.
Switching on/off with the KeyCard:
The set has to be turned on with the
ON button.
Now this volume level is stored as your
mute volume.
Note:
Read the information in chapter
“KeyCard theft protection system”.
2 VOL+ / VOL-
To alter the volume.
Each time the set is switched on, it will
play with the pre-adjusted volume
(VOL FIX).
You may also change the VOL FIX set-
ting (see chapter “DSC programming”).
28
4 Rocker switch
Changer operation
5 Display
Optional:
Coburg RCM 127, Casablanca
RCM 127, Cannes RCM 127
Included in scope of delivery:
Woodstock DJ I, Woodstock DJ A
a
e
d
f g h i j k
l
CD selection
Up
b
c
Down
Radio operation
Title selection
/
Station search
Up
Down
Upwards: Press briefly.
CUE - fast advance (audible):
Keep depressed.
a) NDR1 NDS - Station name
<</>> Up/Down in short intervals
(on FM only if AF is off)
b) TR 1
- Track (side) 1 of the cas-
Downwards: Press as many times
as required.
sette
c) 1 : 52
- Playback TIME or disc
NUMBER during CD
changer operation
- Waveband
- Preset button (1-6)
- Memory bank I, II or
Travelstore
- Seek tuning sensitivity
- Alternative frequency for
RDS operation
To re-start a title: Press briefly.
REVIEW - fast reverse (audible):
Keep depressed.
On FM only:
<</>> To scroll through the station net-
works when AF is on, e.g.NDR 1, 2,
3, 4, N-JOY, FFN, ANTENNE ...
d) FM
e) 5
f) I, II, T
Extra rocker switch functions:
Further setting functions with
Tape operation
AUD
B
A
@
g) lo
h) AF
DSC Mode
PTY
/
Title selection (S-CPS)
Up
Condition: The corresponding function
is activated.
i) TP
- A traffic station is being
received
- Priority for traffic stations
- Loudness
Down
Fast forward
Fast rewind
j) TA
k) LD
l) PTY
Stop function by pressing the opposite key.
- Programme type function
29
6 KeyCard theft protection system
To operate the set it is necessary that
the KeyCard is inserted.
7 FMT (Coburg RCM 127,
Woodstock DJ I)
8 AF
Alternative frequency during RDS op-
BND (Casablanca RCM 127,
Cannes RCM 127, Woodstock DJ A)
For selection of the FM memory banks
I, II and T (Travelstore).
eration:
When “AF” lights up in the display, the
system will automatically seek a fre-
quency offering better reception of the
same RDS programme.
KeyCard
To switch over:
Press button repeatedly.
The selected memory bank will appear
in the display.
AF on/off: Press AF briefly.
Inserting the KeyCard
Regional function on/off:
With the KeyCard tongue sticking out
of the unit, introduce the KeyCard into
the slot with the contact area show-
ing up.
To remove the card, press first to un-
lock.
Press the AF button for approximately
1 sec. until you hear a beep. “REG-
ON” or “REG-OFF” will appear in the
display (see chapter REG - regional
programme).
Travelstore
To store and recall the six most power-
ful stations with Travelstore.
To store: Press button for approxi-
mately 1 sec. until you hear a beep
and “T-STORE” appears in the display.
To recall: Select the memory bank “T”
and press the corresponding preset
button (1-6) briefly.
Read also the information in chapter
“KeyCard theft protection system”.
9 TA (priority for traffic announcements)
When “TA” lights up in the display, the
system will play traffic stations only.
Priority on/off: Press TA.
Flashing KeyCard tongue
When the radio is turned off and the
KeyCard removed, the KeyCard
tongue can be programmed to flash
for optical theft protection.
For more information see chapter
“DSC programming”.
This flashlight can be switched off by
pushing in the tongue and lock.
“WRONG KC” will briefly appear
on the display and the set will switch
off automatically.
Casablanca RCM 127,
: 1, 2, 3, 4, 5, 6 - preset buttons
You can store six stations for each of
the memory banks I, II and T.
Cannes RCM 127, Woodstock DJ A:
Additional selection of medium- and
long-wave stations, provided that “AM
ON” has been adjusted in the DSC
menu.
To store a station: Press a preset
button during radio operation and hold
down until the set resumes play after
the muting and you hear a beep.
To recall a station: Select the desired
memory bank and press the relevant
preset button briefly.
30
Extra function of preset buttons
To store and recall a PTY programme
type.
Extra function of lo button:
To switch between mono and stereo
reception:
? SC
Radio operation
When PTY is active (“PTY” lights up in
the display), you can store and recall
one programme type on/from each
preset button on FM.
Press button for approximately 1 sec.
(beep).
The selected condition will be briefly
displayed.
Scan
Press SC briefly.
The scanned frequency or the station
name will start flashing in the display.
During the actual scanning process
“FM-SCAN” or “AM-SCAN” will be dis-
played. The unit will scan all FM sta-
tions which can be received.
; SRC (Source)
=
/
You can switch between the radio,
tape and CD changer operating
modes, provided that a cassette/CD is
inserted.
To switch the tape side: Press briefly.
To eject the tape: Press for approxi-
mately 1 sec.
Preset Scan
Press SC for approximately 1 sec. until
you hear a beep.
“SCAN” and the name or frequency of
the scanned station will alternately ap-
pear in the display.
Extra function
/
Frequency display during radio opera-
tion:
Press button briefly.
< lo
To switch the seek tuning sensitivity
level:
Press button briefly.
The frequency will be briefly displayed.
The unit will scan all stations stored on
the preset buttons.
If “lo” is displayed, the radio will only
pick up strong, local stations (normal
sensitivity).
> Cassette loading slot
Insert the tape with side A or 1 facing
To stop Scan / Preset Scan:
Press SC once again.
If “lo” does not light up, the radio will
also pick up weaker, distant stations
(high sensitivity).
up, the open side showing to the right.
31
Tape operation
A DSC (Direct Software Control)
Use the DSC function to customise
certain programmable, basic settings
to suit your personal needs and prefer-
ences. See chapter “DSC program-
ming” for more information.
The last setting will be stored automat-
ically.
To switch off AUD: Press button once
again.
If the setting remains unchanged with-
in 8 seconds, the display will switch
back to the previous condition.
Cassetten-Scan
Press SC.
“CC-SCAN” will appear in the display.
All cassette titles will be scanned brief-
ly.
To stop cassette scan:
Press SC once again.
B AUD
Extra function AUD
To adjust the treble, bass, balance and
Loudness - When listening at a low
level, the Loudness function creates a
more natural sound by boosting
the low frequency range.
Loudness on/off: Press AUD for ap-
proximately 1 sec.
“LD” lights up in the display if the
Loudness function is switched on.
Please refer to chapter “DSC program-
ming” for more information on how to
program the Loudness boost.
fader.
Changer operation
If the display shows “TRE” or “BAS”,
you can adjust the reproduction of the
treble and bass frequencies with the
rocker switch. If “BAL” or “FAD” is dis-
played, you can set the balance (left/
right) and fader (front/rear).
Press AUD as many times as required
and make the setting using the rocker
switch.
CD-Scan
Press SC briefly.
“CDC-SCAN” will appear in the dis-
play.
All CD titles will be scanned briefly.
To stop CD-Scan:
Press SC once again.
@ PTY (Programme Type)
In the PTY mode, the preset buttons
become programme type buttons. With
every preset you can select one pro-
gramme type, such as for example
NEWS, SPORT, POP MUSIC, EDU-
CATE, etc.
Treble + / Fader front
Treble – / Fader rear
Bass – / Balance left
Bass + / Balance right
32
Important notes
Installation
Accessories
Precautions
If you would like to install your new car ster- Use accessories and spare parts approved
eo yourself or add other audio components by Blaupunkt only.
Before starting to use your new car radio,
please read the following information care-
fully.
to existing ones, then please read carefully
the enclosed instructions on installation and
ucts with this car radio:
connection.
You can use the following Blaupunkt prod-
Traffic safety
In order to ensure that the set operates prop-
Amplifier
Traffic safety always has the highest priori-
ty.
erly it is necessary that the positive power
All Blaupunkt amplifiers, the preamp-out
supply line is connected to the ignition and
cable 7 607 893 093 is required.
As the driver of a motor vehicle, it is your
responsibility to pay attention to the traffic
situation at all times. Never use your car
radio in a way that could distract you.
Please keep in mind that you travel a dis-
tance of 14 m per second at a speed of only
50 km/h.
Should the traffic situation become particu-
larly demanding, we advise you not to use
the radio.
Always make sure that you are still able to
hear any warning signals coming from out-
side of the vehicle, such as police or fire
engine sirens, so that you can react accord-
ingly.
the permanent +12 V lead.
Do not ground the loudspeaker outputs!
Changer
CDC A 05/F 05
Telephone mute
(adapter cable 7 607 889 093 is required),
If there is a mobile telephone installed in your
vehicle, the radio, tape player or CD player
can be muted automatically when the phone
is being used.
CDC A 06
(Woodstock DJ I, Woodstock DJ A):
CDC A 06 included in the delivery.
“PHONE” will then appear in the display.
When TA is active, traffic messages will al-
ways have priority. The announcement will
be aborted by pressing the TA button.
Remote control
With the infrared remote control RC 06 you
can control all of the important functions of
your car radio system from the steering
wheel.
Therefore, you should always select a mod-
erate volume for playing your car radio while
you are driving.
33
KeyCard theft protection system
This car radio is supplied with one KeyCard The system will switch off after approximate-
as standard, though it can also be operated ly 10 seconds.
•
•
Push in the KeyCard. The card is re-
leased and put in the proper position
for being removed.
with a second card.
When inserting another card type (e.g.
If you have lost your KeyCard or if it was phone or credit card), the display will show
damaged, you can buy a new one from your “WRONG KC” for approximately 2 seconds.
Remove the first KeyCard and insert
the new one.
specialised dealer.
The set will switch off automatically.
After the display indication “READY” or
“LEARN KC”,
When using a second KeyCard, the settings Remove the wrong card and introduce the
stored on the first card will be adopted. How- correct KeyCard.
•
press DSC.
ever, you can individually store the follow-
ing functions:
•
Press ON to turn on the set.
Now you can also use the new KeyCard for
operating your unit.
A maximum of two cards can be used for
the set.
When trying to “train” a third one, the ac-
cess authorisation for the KeyCard not used
for the “training” process will be deleted au-
tomatically.
Bass, treble, balance and fader settings,
Loudness, TA (traffic announcement vol-
ume), beep volume.
Removing the KeyCard
Never pull out the KeyCard directly!
In addition, the settings activated before
switching the radio off, such as the station
tuned in, TA priority, AF, AM ON/OFF and
RM ON/OFF will also remained stored.
This ensures that you will find your basic
settings re-adjusted automatically as soon
as you have inserted your KeyCard.
•
First, slightly push in the KeyCard.
This releases the card and puts it in the prop-
er position for being removed.
•
Now you can pull it out.
Displaying the radio pass data
“Training” a second KeyCard/
Replacing a KeyCard
Using the KeyCard supplied with your set
you can have the radio pass data such as
the model name, product number (7 6..) and
serial number indicated on the display pan-
el.
Putting the unit into operation
While operating the unit with the first
KeyCard, you can “train” a second one to
be also used with the set:
•
Turn on the set.
With the KeyCard tongue sticking out,
introduce the KeyCard into the slot
with the contact area showing up.
Please refer to chapter “DSC programming
- READ KC”.
•
•
•
Insert the first KeyCard and turn on the
set.
Press the DSC button and select
The car radio is now ready for operation.
If a wrong KeyCard is inserted, then “CARD
ERR” followed by “WAIT” will appear in the
display. In this case please do not make any
further adjustments.
“LEARN KC” with
/
.
Press << or >>.
The display will switch to “CHANGE”.
34
Switching the audio source
Short Additional Memory
(S.A.M.)
Optical indication of anti-theft
protection
Using the SRC button you can switch be-
tween the following audio sources:
radio,
tape,
Using the second KeyCard to be purchased Flashing KeyCard tongue
at any specialised dealership, you can pro-
When the vehicle is stationary and the
gram a short text by selecting the DSC menu
item READ KC. This text will be moved
through the display and might be the tele-
phone number of a car repair service or the
emergency call number of your auto club.
Any specialised dealer with the proper
equipment can program the desired text with
up to a maximum of 162 characters onto the
KeyCard.
KeyCard removed, the KeyCard tongue can
be switched to flash for extra anti-theft se-
curity.
For this it is necessary that the positive pow-
er supply line and the permanent +12 V lead
are connected such as described in the in-
stallation instructions.
changer (optional for Coburg RCM
127, Casablanca RCM 127 and
Cannes RCM 127).
Tape/changer operation is only available if
a cassette/disc is inserted.
To switch to another source,
•
press SRC briefly.
Be sure that “LED ON” is adjusted in the
DSC mode.
If required, please refer to chapter “DSC
programming - LED”.
Turn On Message (T.O.M.)
Using the second KeyCard to be purchased
at any specialised dealership, you can pro-
gram the unit to display a selected “Turn On
Message” after the set is switched on.
Any specialised dealer with the proper
equipment can program the desired text with
up to a maximum of 48 characters onto the
KeyCard.
Switching off the flashlight
The flashlight can be switched off by push-
ing in the KeyCard and lock.
If you would like to deactivate the flashing
tongue with general effect, adjust the rele-
vant item in the DSC menu to “LED OFF”.
Each time you switch on your car radio us-
ing the second KeyCard, this text will ap-
pear in the display.
Care of your KeyCard
In order to ensure that the KeyCard always
functions correctly, it is important for the
contacts to be free from any foreign parti-
cles. Avoid direct skin contact.
If necessary, clean the KeyCard contacts
using a cotton swab dipped in alcohol.
35
Radio operation with RDS (Radio Data System)
The Radio Data System offers you more switching on the radio or recalling one of the If you leave the service area of the regional
convenience when listening to FM radio sta- stored frequencies, the unit is automatically programme tuned into, or if you would like
tions.
searching for an alternative frequency.
to take advantage of the full RDS service,
More and more radio stations have begun “SEARCH” will disappear from the display switch to “REG OFF”.
to broadcast RDS information alongside when the alternative frequency has been
their programmes. found or after the frequency band has been
•
Press the AF button for approximately
1 sec. until “REG OFF” appears.
As soon as a programme has been identi- run through completely.
fied, the station name including a regional If the reception quality of the selected pro-
identifier, if applicable, will appear in the dis- gramme becomes too bad:
If the REG function is active, “REG ON” will
be briefly displayed each time the radio is
switched on.
play, for example, NDR1 NDS (regional pro-
gramme in Lower Saxony, Germany).
When RDS is activated, the preset buttons
become programme buttons. You now know
exactly which programme you have tuned
into, making it easy to find the desired sta-
tion quickly.
•
Tune into another station.
Selecting a waveband
(only Casablanca RCM 127,
Cannes RCM 127, Woodstock DJ A)
REG - regional programme
Certain radio programmes are split up at
times into regional programmes offering lo-
cal information. The 1st programme broad-
cast by NDR, for example, offers pro-
grammes with different contents in the north-
ern states of Germany Schleswig-Holstein,
Hamburg and Lower Saxony at certain times
of the day.
If you are listening to one regional pro-
gramme and move to an area where anoth- Note:
er linked regional programme becomes In the DSC menu you can deactivate the
stronger, the unit will switch to that pro- station selection on either MW or LW or for
gramme.
You can select between the following wave-
bands:
FM 87.5 - 108 MHz
MW 531 - 1602 kHz
LW 153 - 279 kHz
But RDS offers you further advantages:
AF - Alternative frequency
•
Press the BND button until the desired
The AF (Alternative Frequency) function
makes sure that the strongest frequency of
the currently selected programme is always
tuned in automatically.
This function is activated when “AF” appears
in the display.
waveband shows on the display panel.
both wavebands at the same time.
In order to switch this function on or off,
If you wish to continue listening to the first This has the advantage that only the re-
programme,
press the AF button for approximately
quired bands will allow to be activated, so
that you must press the BND button less
often. For more information, please refer to
chapter “DSC programming - AM ON/OFF”.
•
press the AF button briefly.
•
While searching for the strongest reception
signal, the radio may switch to mute briefly.
If “SEARCH” appears in the display when
1 sec.
“REG ON” appears in the display.
36
Station tuning
Manual tuning:
Changing the memory bank
•
Press << >>; the frequency will change
in short intervals in downwards or up-
wards direction.
Automatic tuning
/
You can shift between the memory banks I,
II and T in order to store stations and recall
them later.
The currently selected memory bank is in-
dicated in the display.
•
Press
cally search for the next station.
When keeping the upper or lower part
/
; the car radio will automati-
When holding the right or left part of the rock-
er switch depressed, the frequency scan is
speeded up.
/
of the rocker switch depressed, seek tuning
will speed up in upwards or downwards di-
rection.
•
Press the FMT or BND button as many
times until the desired memory bank
lights up in the display.
Scrolling through the broadcast-
ing networks
You can use the << >> buttons to tune in Storing stations
stations of your reception area.
On FM, you can store six stations on the
preset buttons 1-6 for each of the memory
banks I, II and T.
On MW/LW, you can also store six stations
each. (only with Casablanca RCM 127,
Cannes RCM 127, Woodstock DJ A)
If several programmes of the broadcasting
networks can be received, you can scroll
through them in forwards direction pressing
>>, or backwards using the << button, e.g.
NDR 1, 2, 3, 4, N-JOY, FFN, ANTENNE ...
For this it is necessary that the stations have
been tuned in at least once and that “AF” is
active (lights up in the display).
Seek tuning
Up
Down
Down in short intervals
(“AF” must be switched off)
Up in short intervals
(“AF” must be switched off)
•
•
Select the desired memory bank.
Tune in a station with the rocker switch
(either automatically or manually).
For this purpose, you may start Travelstore
seek operation:
•
Press and hold down the desired pre-
set button until the radio resumes play
after the muting (takes approximately 1
sec., confirmed by beep).
•
Press FMT or BND for 1 sec.; the
system starts to run through the fre-
quency band. The display shows
“T-STORE”.
Manual tuning with << >>
You can also tune in a station manually.
Condition:
Now the station has been stored.
AF and PTY must be switched off (i.e. the
symbols do not light up in the display).
If “AF” does not light up,
press AF.
The activated preset button is indicated in
the display.
•
If necessary, deactivate these functions:
This fulfils the requirements for selecting
stations with << >>.
•
Press AF or PTY briefly.
37
Notice:
Recalling stored stations
Scanning stations with Radio-
Scan
Should you tune in a station which has al-
ready been stored before, then the corre-
sponding preset position and memory bank
will briefly flash in the display.
You can recall any stored station at the touch
of a button.
You can also scan all stations which can
currently be received.
•
Select the memory bank with FMT or
BND.
To start the Scan function:
•
Press the corresponding preset button
briefly to recall the station.
•
Press SC briefly.
Automatically storing the
strongest stations with
Travelstore
The scanned frequency or the station name
will start flashing in the display. During the
actual scanning process “FM-SCAN” or
“AM-SCAN” will be displayed.
Scanning stored stations with
Preset Scan
You can automatically store the six most
powerful FM stations of your current recep-
tion area sorted according to their signal
To select a scanned station and switch
off Radio-Scan:
You can have all of the stored stations briefly
strength. This function is particularly conven- scanned on all wavebands.
•
Press SC briefly.
ient on longer trips.
To start Preset Scan:
If no station is selected, the scan function
will be automatically switched off after the
frequency band has been run through com-
pletely. The unit will tune in the station lis-
tened to before starting the scan.
•
Press the FMT or BND button for
•
Press SC for approximately 1 sec.
1 sec.
All of the stored stations to be received will
be scanned one after the other.
“T-STORE” will appear in the display.
The six strongest FM stations will be auto-
matically stored on the memory bank “T”
(Travelstore). When this process has been
completed, the radio will play the first sta-
tion stored on preset 1.
If desired, stations can also be stored man-
ually on the Travelstore bank (see “Storing
stations”).
To select a scanned station and switch
off Preset Scan:
•
Press SC briefly.
Note:
If “TA” shows on the display panel, the sys-
tem will scan the stored traffic stations only.
38
Selecting the seek tuning sensi- Loudness
tivity
Programme type
Adjusts the low bass frequencies for a more Use << >> to have the last selected pro-
You can alter the automatic seek tuning natural sound.
gramme type displayed and to choose a new
one.
sensitivity.
Switching Loudness on/off:
If “lo” is displayed, the radio will only pick up
strong, local stations.
If “lo” does not light up, the radio will also
pick up weaker, distant stations.
You can select any one of the stored types
with the preset buttons 1-6.
Condition: PTY must be active.
Using DSC you can choose between Ger-
man and English (see “DSC programming -
PTY LANG”).
All of the programme types listed below are
available.
The letters printed in bold are identical to
the actual short-time indication in the dis-
play.
•
Press the AUD button for approximate-
ly 1 sec.
When the Loudness function is active, “LD”
will light up in the display.
See chapter “DSC programming” for more
information.
To switch the seek tuning sensitivity:
•
Press lo briefly.
The sensitivity level can be altered sepa-
rately in both modes. Please refer to chap-
ter “DSC programming - S-LO, S-DX”).
PTY – Programme-Type
PTY is an RDS service offered by more and
more radio broadcasters. This feature allows
you to select FM stations according to their
programme type. After you have chosen the
PTY of your preference, the corresponding
stations can be selected either by seek tun-
ing or using the scan function.
Switching from stereo to mono
NEWS
Every time the radio is switched on, stereo
playback is activated automatically.
The unit will gradually switch to mono if re-
ception is poor.
You can also switch between mono and ster-
eo reception manually:
CURRENT AFFAIRS
INFORMATION
SPORT
EDUCATE
DRAMA
CULTURE
Switching PTY on/off
•
Press the lo button for approximately
1 sec.
SCIENCE
VARIED
POP MUSIC
ROCK MUSIC
M.O.R. M (middle of the road music)
LIGHT M (light classical)
CLASSICS (serious classical)
•
Press PTY.
When the function is active, the programme
type selected last will briefly appear in the
display. “PTY” will be permanently indicat-
ed in the lower right corner of the display
panel.
The selected condition will briefly appear in
the display.
39
OTHER M (other music)
WEATHER
Displaying the selected programme
type
b) Using the << >> buttons of the rocker
switch
FINANCE
When PTY is switched on, you can se-
lect a programme type using buttons
<< >>.
•
Press << or >>.
CHILDREN’S PROGRAMMES
SOCIAL AFFAIRS
RELIGION
PHONE IN
TRAVEL
The programme type selected last will be
displayed briefly.
•
•
•
Press << or >>; the programme
type selected last will be displayed
for 3 seconds.
Selecting a programme type
a) Using the preset buttons
HOBBIES
JAZZ MUSIC
During this period press >> (for-
wards) or << (backwards) to select
the desired type.
When PTY is switched on, you can use
the preset buttons 1-6 to select the
programme types stored at the factory.
COUNTRY MUSIC
NATIONAL MUSIC
OLDIES MUSIC
FOLK MUSIC
DOCUMENTARY
ALARM TEST
Press << or >> as many times as
required.
•
Press one of the presets 1-6.
The selected programme type will be
displayed for 2 seconds.
If you wish to listen to a station offering
the selected PTY,
If you wish to listen to a station with
this PTY,
•
press
/
to start seek tuning.
Checking the programme type of the
station
If the system is unable to find a station of-
fering the selected programme type, the dis-
play will show “NO PTY” and a beep tone
will be released. The station received be-
fore starting seek tuning will be tuned in.
•
press
/
to start seek tuning.
If the system is unable to find a station of-
fering the selected programme type, the dis-
play will show “NO PTY” and a beep tone
will be released. The station received be-
fore starting seek tuning will be tuned in.
You can assign different programme types
to each preset position. Please refer to chap-
ter “Storing programme types”.
•
Press PTY for approximately 1 sec.
After the beep tone the display will show the
programme type offered by the tuned in sta-
tion.
If “NONE” appears in the display, the cur-
rent station has no PTY code.
40
Storing programme types
PTY priority
During tape operation, the set will also au-
tomatically switch to the programme offer-
ing the selected PTY within the broadcast-
ing network.
After the PTY programme the system will
remain in the radio mode.
At the factory, one programme type was Situation:
assigned to each of the preset buttons 1-6.
PTY is switched on and lights up in the dis-
If desired, you can also store other availa-
ble programme types.
play.
No station offering the selected programme
type can be currently received (neither with
seek tuning nor with scan).
To do so, make sure that “PTY” lights up in
the display.
•
•
•
If necessary, press the PTY button to
switch on the function.
The set will switch back to the previous sta-
tion.
Notice:
As mentioned earlier, these functions are
currently only supported by a limited number
of RDS stations.
As soon as a programme with such PTY can
be received within the broadcasting network,
the unit will switch over to the correspond-
ing station for the duration of the pro-
gramme.
Select a programme type using but-
tons << >> and
hold down the desired preset button
(1-6) until you hear a beep.
Now the selected programme type can be
recalled by pressing this preset. For this, the
PTY function must be active.
Example: German broadcasting network
NDR:
-
-
-
-
-
Station tuned in: NDR3.
Scanning stations with PTY-SCAN
“PTY” lights up in the display.
Programme type “POP” selected.
Seek tuning is started.
Condition: “PTY” must appear in the display.
•
Press the SC button.
All of the received stations offering the se-
lected programme type will be scanned.
No station with “PTY-POP” can be
found.
To switch off PTY-SCAN:
•
Press SC once again.
-
-
-
-
The display shows “NO PTY” and
automatically switches back to NDR3.
NDR2 airs a “PTY-POP” programme.
The system will switch to the linked
NDR2 station for the duration of the
“POP” programme.
41
Receiving traffic programme stations with RDS-EON
The abbreviation “EON” stands for En- Traffic announcement priority
Switching off the beep tone
hanced Other Networks, meaning the ex- on/off
a) Tune into another station offering traf-
fic information:
change of information within a radio network.
If the priority for traffic announcement pro-
Many FM broadcasters offer traffic messag-
grammes is activated, “TA” will light up in
es for their service area at regular intervals.
the display.
•
•
Press the rocker switch or
press a preset button which has a
traffic programme station allocated
to it.
All traffic programme stations transmit a
special carrier signal alongside their pro-
To switch the priority on or off:
•
Press the TA button.
grammes, which is decoded by your car ra-
dio. If this signal is identified, “TP” will ap- When pressing TA while a message is be-
Alternatively:
pear in the display (Traffic Programme).
In addition to these, there are also stations
ing broadcast, this message will be inter-
rupted. The unit will then switch back to the
b) Switch off the priority for traffic an-
nouncements:
which do not actually transmit traffic pro- previous condition. The priority for all other
grammes themselves, but by using RDS- traffic messages remains active.
•
Press TA.
“TA” will disappear from the display.
EON they offer the possibility to receive the
Please note that several buttons have no
traffic messages broadcast by another traf- function while a traffic announcement is
fic programme station in the same radio broadcast.
network.
Automatic seek tuning start
(tape and CD changer operation)
If you wish to have the priority for traffic an-
nouncements activated while listening to
one of these stations (e.g. NDR3), “TA” must
appear on the display panel.
If a traffic announcement is broadcast, the
radio will automatically switch to the linked
traffic programme station (in this case,
NDR2) for the duration of the message and
return to the original programme (NDR3)
afterwards.
Beep tone
When leaving the reception area of the tuned
in traffic programme station while listening
to a tape or CD, the system will automati-
cally start searching for a new TA pro-
gramme.
If no such station is found within approxi-
mately 30 seconds, you will hear a warning
beep every 30 seconds. To switch off the
beep tone proceed as described above.
If you leave the reception area of the traffic
programme station currently tuned into, you
will hear a beep tone approximately every
30 seconds.
This tone will also be released when press-
ing a preset button which has no traffic pro-
gramme allocated to it.
42
Tape operation
Adjusting the volume for traffic
announcements and the beep
tone
Fast Forward/Rewind
The car stereo has to be switched on.
The unit will automatically switch to tape
operation when inserting a cassette.
This volume was preset at the factory,
though you can alter the value using the
DSC function (see “DSC programming, TA
VOL”).
If the volume level is altered while a mes-
sage is being played, this will only affect the
current announcement.
Inserting a tape
•
•
Turn on the set.
Insert a tape.
Fast forward
Fast rewind
The cassette will be automatically transport-
ed to the playback position. Side A or 1 starts
to play.
/
Title selection (S-CPS)
During tape operation, “TR 1” or “TR 2”
(track) will be indicated on the display pan-
el.
Up
Down
Stop function by pressing
.
Insert the tape with side A or 1 facing up, the open side
showing to the right.
Selecting titles with CPS
(Cassette Programme Search)
Use this function to skip ( ) and repeat (
recorded titles.
)
To start CPS:
Removing a tape
•
Press
/
.
In order for CPS to function properly, there
has to be an unrecorded tape portion of at
least 3 seconds between the individual ti-
tles.
•
Press
The cassette will eject.
for 1 sec.
43
Switching the tape side
(autoreverse)
Scanning cassette titles with
SCAN
Care notes
To avoid possible problems, we recommend
To change the tape direction during cassette You can have the cassette titles played brief- you to use C-60/C-90 type cassette tapes
playback:
Press
At the end of a tape side the mechanism
changes directions automatically to play the To start/stop the scan function:
ly by using the scan function. If you like a only. Store your tapes in a cool place away
title, stop the scan to continue listening to from dirt, dust and temperatures exceeding
•
briefly.
that track.
50 °Celsius. Allow very cold tapes to warm
up before playing them in order to avoid
uneven tape transport. After approximately
100 hours of use, dust particles collected
on the playback head or roller may lead to
tape run problems and sound distortions.
Use a head cleaning tape to remove nor-
mal dirt build-up. For tougher cases, use a
cotton swab (Q-Tip) dipped in alcohol. Do
not attempt to clean by inserting a hard ob-
ject into the player!
other side (autoreverse). The display shows
•
Press the SC button briefly.
“TR 1” for track (side) 1 or “TR 2” for track 2.
Scan condition: There has to be an unre-
corded tape portion of at least 3 seconds
between the individual titles.
Notice:
If there is too much tension on the tape dur-
ing playback, the set may switch over by it-
self before having reached the end of the
tape side. In this case check the condition
of the cassette tape. Sometimes it helps to
rewind it completely.
Listening to the radio during
fast tape winding with RM
(Radio Monitor)
When the tape is fast forwarded or rewound
(also with CPS), the radio will normally be
muted. In order to listen to the radio during
fast winding, you can activate the Radio
Tape equalisation
When a metal or CrO2 tape is inserted, the Monitor function.
tape mechanism automatically adjusts to For more information please refer to chap-
metal/CrO2 tape equalisation.
ter “DSC programming - RM ON/OFF”.
44
CD changer operation
Selecting CDs and titles
MIX playback
Optional:
Coburg RCM 127, Casablanca RCM 127,
Cannes RCM 127
You can have the CD tracks played in ran-
dom order.
Included in scope of delivery:
Woodstock DJ I, Woodstock DJ A
Select the desired MIX mode in the DSC
menu.
This piece of equipment offers you conven-
ient control of a Blaupunkt CD changer CDC-
A 05/F 05 (with adapter 7 607 889 093) /
CDC-A 06.
MIX CDC – The MIX mode is active:
The individual discs and the
titles of the selected CD are
chosen randomly. After all
titles have been played, the
next CD will be selected at
random again.
CD selection
Up
Down
Note:
Use only perfectly circular CDs.
Title selection
CDs manufactured in the shape of a butter-
fly or a beer mug, for example, are not suit-
able for use with this equipment.
Using such CDs can very likely result in the
destruction of the CD and the CD drive.
We assume no responsibility for damages
caused by using unsuitable CDs.
Use to select a CD title in
random order.
Upwards: Press briefly.
CUE - fast advance (audible): Keep
depressed.
MIX OFF – The Mix function is deactivat-
ed. Discs and titles will be
Downwards: Press as many times as
required.
To re-start a title: Press briefly.
REVIEW - fast reverse (audible):
Keep depressed.
selected in numeric order.
To change the MIX mode:
•
Press DSC.
Switching to the CD changer
mode
Select “MIX” using the rocker switch
/
and adjust with
/
.
If the function is active, “CDC MIX” will be
displayed every time CD changer operation
is activated.
Make sure that at least one CD has been
inserted into the magazine.
Press SRC to toggle the audio source:
•
Press repeatedly until the CD functions
appear in the display.
45
Selecting the display mode
SCAN
You can select the desired display mode for Use this function to scan all of the CD tracks.
CD playback:
To start the Scan function:
“CDC NUMBER” – The CD number, such
•
Press SC.
as “CD 8” is dis-
played.
The titles will be scanned one after the oth-
er in ascending order.
“TIME”
– The elapsed playback
time of the current title
is displayed, for ex-
ample “2 : 32”.
To stop the Scan function:
•
Press SC briefly.
The track currently being scanned is con-
tinued to be played.
SCAN will also be terminated by
To switch the display mode:
•
pressing one of the buttons AUD,
•
Press DSC.
GEO, DSC, SRC, << >> or / .
Use the rocker switch
“CDC DISP”.
/
to select
•
Use
/
to adjust to “NUMBER” or
“TIME”.
You can also change the display mode im-
mediately for the title currently playing by
pressing
.
46
DSC programming
MIX
For changer operation only.
RM ON / OFF (Radio Monitor)
Allows you to listen to the
DSC (Direct Software Control) allows you
to customise certain programmable, basic
settings to suit your personal needs and
preferences and then store them.
The basic settings for this audio equipment
were made at the factory.
In the following you can find an overview of
these settings, so that you can always reset
to these if desired.
MIX CDC -
radio during fast winding of
the tape.
RM ON – Radio playback
activated
RM OFF – Function deacti-
vated
CD selection at random.
All titles of this disc will be
chosen in random order as
well.
The next disc is again se-
lected at random.
MIX OFF -
The MIX function is
switched off.
If you wish to alter any of the programming,
LOUDNESS When listening at a low lev-
el, the Loudness function
creates a more natural
sound by boosting the low
frequency range.
•
press SRC to choose the desired oper-
ating mode (e.g. radio, if you wish to
change the language with PTY LANG).
AM ON / OFF (Casablanca RCM 127,
Cannes RCM 127, Wood-
stock DJ A)
•
press DSC.
LOUD 1 - Low boost
LOUD 6 - Max. boost
Use the rocker switch to select and adjust
the functions described in the following. The
display will show you the adjusted condition.
You can deactivate one or
both AM bands (MW/LW) in
order to reduce the number
of bands for selection with
BND.
TA VOL
To adjust the traffic an-
nouncement and beep tone
volume from between 0 to
63.
selectable:
The message will then come
through at this volume, if the
standard volume is lower.
If the standard volume is
higher than the TA VOL lev-
el, the traffic report will be
played slightly louder than
the standard volume.
AM ON – all bands
MW OFF – LW, FM
LW OFF – MW, FM
AM OFF – FM
/
Select function
<< >>
Adjust/recall value
47
BEEP
Acknowledgement tone for
all functions which require a
button to be pressed for
more than 1 second.
The volume can be adjusted
from between 0 to 9. (0 =
off)
READ KC
To read out the KeyCard
data.
S-LO
To adjust the seek tuning
sensitivity for local recep-
tion.
LO 1 - high sensitivity
LO 3 - low sensitivity
The seek tuning sensitivity
values can be set separately
for AM and FM.
The KeyCard supplied with
the radio is used to display
the model name, type
number (7 6..) and the serial
number.
Using the second KeyCard
to be purchased at any spe-
cialised dealership it is pos-
sible to display the Short
Additional Memory (S.A.M.)
data entered by the dealer.
See chapter “Short Addition-
al Memory S.A.M.”.
LED ON/OFF You can choose between
LED ON or LED OFF. With
LED ON, the KeyCard
AUX ON/OFF Please note that this item
will not appear if you have
connected a CD changer.
Default setting: AUX OFF.
Adjust to AUX ON if you
have connected an external
piece of equipment to the
AUX socket.
tongue will flash for extra
anti-theft protection when
the unit has been switched
off and the KeyCard re-
moved.
If you remove the KeyCard
during the reading process,
“READ KC” will show on the
display panel.
LEARN KC To “train” a second
KeyCard.
VOL FIX
Use this function to select
the volume at which the ra-
dio is set when it is switched
on. Adjust the desired vol-
ume level with << >>. When
adjusted to “VOL 0”, the
system will come on with the
volume selected before
switching it off.
Please read the information
in chapter “KeyCard theft
protection system - Training
a second KeyCard”.
PTY LANG To select the programme
type language: DEUTSCH
or ENGLISH
S-DX
To adjust the seek tuning
sensitivity for distant recep-
tion.
DX 1 - high sensitivity
DX 3 - low sensitivity
48
Appendix
To quit the DSC programming mode
and store the adjustment:
Specifications
Blaupunkt
telephone hotline
Amplifier
•
Press DSC.
Output power:
4 x 23 W RMS power
acc. to DIN 45324 at
14.4 V
The DSC programming mode will be auto-
matically quit 8 seconds after having made
the last adjustment.
Address of the next service
centre in your vicinity
(only for Germany)
4 x 35 W max. power
Tuner
Wavebands:
Overview of DSC factory set-
tings
If you would like to know the address of
the next Blaupunkt service centre of
your area without having our service list
at hand:
FM
:
87.5 – 108 MHz
MIX
OFF
(Casablanca RCM 127, Cannes RCM 127,
Woodstock DJ A)
RM
OFF
LOUDNESS
TA VOL
BEEP
3
35
4
MW
LW
531 – 1602 kHz
153 – 279 kHz
-
-
Find out your area code.
Then call the following chargeable
LED
ON
phone number: 01 80 / 5 25 56 66.
FM sensitivity:
0.9 µV at 26 dB signal-
to-noise ratio
LEARN KC
READ KC
PTY LANG
S - DX
S - LO
VOL FIX
-
-
-
Using the area code to be entered
you will be automatically given the
address and phone number of the
next Blaupunkt service centre. You
can also request this information
by fax.
ENGLISH
FM frequency response:
30 - 16 000 Hz
1
1
0
Tape player
(Casablanca RCM 127, Cannes RCM 127,
Woodstock DJ A):
Frequency response:
30 - 18 000 Hz
AM
ON
CD changer
Frequency response:
5 - 20 000 Hz
Subject to modifications!
49
|