KS800(S)(SL)(SW)(SWL)
3
4
5
f. If operating a power tool in a damp location is
unavoidable, use a Residual Current Device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Intended use
Your Black & Decker jigsaw has been designed for sawing
wood, plastics and metal. This tool is intended for consumer
use only.
3. Personal safety
Safety instructions
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
General power tool safety warnings
Warning! Read all safety warnings and all
!
instructions. Failure to follow all instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
c. Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
battery pack from the power tool before making
the
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
6
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Do not touch the workpiece or the blade
immediately after operating the tool. They can
become very hot.
Be aware of hidden hazards, before cutting into
walls, floors or ceilings, check for the location of
wiring and pipes.
The blade will continue to move after releasing the
switch. Always switch the tool off and wait for the saw
blade to come to a complete standstill before putting the
tool down.
Warning! Contact with, or inhalation of dusts arising from
cutting applications may endanger the health of the operator
and possible bystanders. Wear a dust mask specifically
designed for protection against dust and fumes and ensure
that persons within or entering the work area are also
protected.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will make sure that the safety of the power tool is
maintained.
Safety of others
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a
person responsible for the their safety.
Additional power tool safety warnings
!
Warning! Additional safety warnings for jigsaws.
Children should be supervised to ensure that they do
not play with the appliance.
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing one
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
Keep hands away from cutting area. Never reach
underneath the work piece any reason. Do not insert
fingers or thumb into the vicinity of the reciprocating
blade and blade clamp. Do not stabilize the saw by
gripping the shoe.
Keep blades sharp. Dull or damaged blades may
cause the saw to swerve or stall under pressure. Always
use the appropriate type of saw blade for the workpiece
material and type of cut.
When cutting pipe or conduit, make sure that they
are free from water, electrical wiring, etc.
7
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the
tool is switched off and when it is running idle in addition to
the trigger time.
This laser complies with class 2 according to EN 60825-
1:1994+A1:2002+A2:2001. Do not replace a laser diode
with a different type. If the laser is damaged, have the laser
repaired by an authorised repair agent.
Do not use the laser for any purpose other than projecting
laser lines.
An exposure of the eye to the beam of a class 2 laser is
considered safe for a maximum of 0.25 seconds. Eyelid
reflexes will normally provide adequate protection. At
distances greater than 1m, the laser complies with class 1
and is therefore considered completely safe.
Never look into the laser beam directly and intentionally.
Do not use optical tools to view the laser beam.
Do not set up the tool where the laser beam can cross any
person at head height.
Labels on tools
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
Do not let children come near the laser.
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Features
1. Lock-on button
2. On/off switch
3. Blade storage compartment cover
4. Shoe plate locking lever
5. Dust extraction outlet
6. Dust extraction adaptor
7. Shoe plate
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Additional safety instructions for non-rechargeable
batteries
8. Auto SelectTM dial
9. Blade support roller
10. Tool-free blade clamp
Never attempt to open for any reason.
Do not store in locations where the temperature may
exceed 40°C.
When disposing of batteries, follow the instructions
given in the section "Protecting the environment".
Additional features (fig. A)
Additional features may be applicable depending upon the
product purchased. The additional features applicable to the
catalogue number purchased are shown in fig. A.
Do not incinerate the batteries.
Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries, proceed as
follows:
- Carefully wipe the liquid off using a cloth. Avoid skin
contact.
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and
that the saw blade has stopped. Used saw blades may be
hot.
Additional safety instructions for lasers
Fitting the saw blade (fig. B)
Read all of this manual carefully.
Hold the saw blade (11) as shown, with the teeth facing
forward.
Push and hold the blade clamp (10) down.
Insert the shank of the saw blade into the blade holder
(12) as far as it will go.
This product is not to be used by children
under 16.
Release the blade clamp (10).
Laser radiation.
Saw blade storage (fig. C)
Do not look into the laser beam.
Saw blades (11) can be stored in the storage compartment
located on the side of the tool.
Do not use optical tools to view the laser
beam.
8
Open the cover (3) of the saw blade storage
compartment by holding the tab on the top of the cover
(3) and pulling it outward.
The blades are retained in the compartment by a
magnetic strip. To remove a blade, press down on one
end of the blade to raise the other end, and remove.
Close the cover (3) of the saw blade storage
compartment and make sure that it is latched closed.
Pull the shoe plate locking lever (4) outwards to unlock
the shoe plate (7).
Set the shoe plate (7) to an angle of 0° and push the
shoe plate backwards.
Push the shoe plate locking lever (4) back towards the
saw to lock the shoe plate (7).
Warning! Close the compartment door securely before
operating the saw.
Connecting a vacuum cleaner to the tool (fig. D)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool. The dust extraction adaptor (6) can be
purchased from your local Black & Decker retailer.
Push the adaptor (6) into the dust extraction outlet (5).
Connect the vacuum cleaner hose to the adaptor (6).
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Use
Adjusting the shoe plate for bevel cuts (fig. E and F)
Warning! Never use the tool when the shoe plate is loose or
removed.
The shoe plate (7) can be set to a left or right bevel angle of
up to 45°.
Pull the shoe plate locking lever (4) outwards to unlock
the shoe plate (7) from the 0 deg position (fig. F).
Pull the shoe plate (7) forward and set the required
bevel 15°, 30° and 45° indicated in the bevel angle
window.
Push the shoe plate locking lever (4) back towards the
saw to lock the shoe plate (7).
To reset the shoe plate (7) for straight cuts:
9
How to use the Auto SelectTM dial (fig. G)
This tool is fitted with a unique Auto SelectTM Dial (8) to set the speed and the pendulum blade action for various cutting
applications. To select the optimum speed and pendulum blade action for the type of material being cut, turn the dial (8) as
shown in the table below:
Icon
Application
Speed
Blade Type
Kitchen work surfaces, Fast speed
work tops, laminate
board
General wood
Scrolling/curves/
craftwork, hardwoods,
decking, flooring
Plywood and wood
panels
Fast speed
Scrolling wood
General wood
Fast speed
General wood
General timber, soft Fast speed
wood, fast rip cutting
General wood
Plastics, Perspex, PVCMedium speed
General purpose
Sheet metal tin plate, Low speed
ceramic tile, fibreglass
sheet
Metal orceramicor
fibreglass blade
Slow speed, precision Slow speed
start
Choosethecorrect
blade for the
application
Switching on and off
match the (+) and (-) terminals correctly. Re-attach the laser
module (14).
To switch the tool on, press the on/off switch (2).
To switch the tool off, release the on/off switch (2).
For continuous operation, press the lock-on button (1)
and release the on/off switch (2).
Adjusting the laser side-to-side (fig. I)
Note: The laser is intended as a cutting aid and does not
guarantee a precise cut.
To switch the tool off when in continuous operation,
press the on/off switch (2) and release it.
Warning! Do not adjust the laser with the jigsaw plugged in.
Use the laser adjustment screw (15) to align the laser line
with the saw blade if needed.
Sawing
Hold the tool firmly with both hands while cutting.
The laser visibility (power) will be reduced if the jigsaw is
overheated. The laser may not be visible when the saw is
overloaded for a prolonged period of time. The laser visibility
will gradually return to normal when the tool cools down even
when the tool is unplugged.
The shoe plate (7) should be held firmly against the material
being cut. This will help prevent the saw from jumping,
reduce vibration and minimise blade breakage.
Let the blade run freely for a few seconds before starting
Warning! Do not leave the overheated laser switched ON.
Make sure that the switch is in the OFF position and remove the
batteries to remove power from the laser.
the cut.
Apply only a gentle pressure to the tool while performing
the cut.
Using the laser (fig. J and K)
Operating the laser (fig. H - K) (‘L’ units only)
Installing the batteries (fig. H)
The laser projects the line of cut (18) on to the surface of the
workpiece.
Detach the laser module (14) from the jigsaw by removing
the screw (13) and pulling the laser module forward. Insert
two new 1.5 Volt AAA alkaline batteries, making sure to
To switch the laser on, press the button (16).
To switch the laser off, press the button (16) again.
10
Viewing from directly above the jigsaw, the line of cut (17)
can be easily followed. Should this view be restricted for any
reason, the laser can be used as an alternative cutting guide.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Use a pencil to mark the cutting line (17).
Position the jigsaw over the line (17).
Switch on the laser.
Connect the brown lead to the live terminal in the new
plug.
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
Operating the work light (fig. L and M) ('W' units only)
Units that include a 'W' in the catalogue number are provided
with an LED light (19) to illuminate the area around the
blade.
Protecting the environment
To switch the work light on, slide the switch (20) to the on
position (I).
To switch the work light off, slide the switch (20) to the
off position (0).
Separate collection. This product must not be
disposed of with normal household waste.
Hints for optimum use
Sawing laminates
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
When cutting laminates, splintering may occur which can
damage the presentation surface. The most common saw
blades cut on the upward stroke, therefore if the shoe plate
is sitting on the presentation surface either use a saw blade
that cuts on the downward stroke or:
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Use a fine-tooth saw blade.
Saw from the back surface of the workpiece.
To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw
through this sandwich.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Sawing metal
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have
reached the end of their working life. To take advantage of
this service please return your product to any authorised
repair agent who will collect them on our behalf.
Be aware that sawing metal takes much more time than
sawing wood.
Use a saw blade suitable for sawing metal.
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut
through this sandwich.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
Spread a film of oil along the intended line of cut.
Maintenance
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Batteries
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Never let any liquid get inside the tool and never
immerse any part of the tool into liquid.
At the end of their useful life, discard batteries with
due care for our environment.:
Do not short-circuit the battery terminals.
Do not dispose of the battery(s) in a fire as this may
result in a risk of personal injury or an explosion.
11
Technical data
EC declaration of conformity
KS800S
MACHINERY DIRECTIVE
KS800SL
KS800SW
KS800SLW
TYPE 1
Voltage
Vac 230
W 520
min-1 800-3000
KS800S, KS800SL, KS800SW, KS800SLW
Rated input
No-load speed
Max. depth of cut
Wood
Steel
Aluminium
Weight
Black & Decker declares that these products described
under "technical data" are in compliance with:
2006/42/EC, EN60745-1, EN60745-2-11
mm 70
mm 5
mm 15
kg 2.2
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of Black
& Decker.
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 89 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 100 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum)
according to EN 60745:
Kevin Hewitt
Cutting wood (ah CW) 6.0 m/s2, uncertainty (K) 1.5 m/s2
Vice-President Global Engineering
Black & Decker Europe,
210 Bath Road, Slough,
Berkshire, SL1 3YD
Cutting sheet metal (ah CM ) 6.5 m/s2, uncertainty (K) 1.5 m/s2
,
United Kingdom
10-02-2010
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement
is in addition to and in no way prejudices your statutory
rights. The guarantee is valid within the territories of the
Member States of the European Union and the European
Free Trade Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker
guarantees to replace defective parts, repair products
subjected to fair wear and tear or replace such products to
make sure of the minimum inconvenience to the customer
unless:
The product has been used for trade, professional or
hire purposes.
The product has been subjected to misuse or neglect.
The product has sustained damage through foreign
objects, substances or accidents.
12
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service
staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-
sales service and contacts are available on the Internet at:
register your new Black & Decker product and to be kept up
to date on new products and special offers. Further
information on the Black & Decker brand and our range of
13
TYP.
1
KS800S - KS800SL - KS800SW - KS800SLW
2
33
4
3
13
18
20
21
15
5
19
14
9
7
55
52
17
16
1
51
12
10
8
22
23
6
25
11
57
53
24
59
29
31
54
58
56
60
28
30
43
42
32
33
41
27
69
34
61
47
49
35
26
36
46
50
SL - SLW
28
44
66
67
37
48
65
SW - SWL
62
39
38
68
40
63
45
64
GB
23 - 03 - 10
E16012
ENGLISH
Do not forget to register your product!
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
$XVWUDOLD
%ODFNꢀ ꢀ'HFNHUꢀꢁ$XVWUDOLDꢂꢀ3W\ꢃꢀ/WGꢃꢀ
ꢉꢄꢀ)OHWFKHUꢀ5RDGꢌꢀ0RRURROEDUNꢌꢀꢀ
9LFWRULDꢌꢀꢅꢋꢅꢇꢀ
7HOꢃꢀꢄꢅꢆꢇꢈꢉꢄꢀꢊꢋꢄꢄ
)D[ꢀꢄꢅꢆꢍꢈꢉꢈꢀꢊꢍꢎꢄꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
1HZꢀ=HDODQG
%ODFNꢀ ꢀ'HFNHUꢀ
ꢊꢀ7Hꢀ$SXQJDꢀ3ODFHꢀ
0Wꢀ:HOOLQJWRQ
7HOꢃꢀꢏꢐꢎꢀꢍꢀꢉꢊꢍꢀꢋꢋꢅꢅ
)D[ꢀꢏꢐꢎꢀꢍꢀꢉꢊꢍꢀꢋꢋꢉꢉ
$XFNODQGꢀꢋꢄꢐꢄ
8QLWHGꢀ.LQJGRP
%ODFNꢀ ꢀ'HFNHUꢀ
ꢉꢋꢄꢀ%DWKꢀ5RDGꢀ
6ORXJKꢌꢀ%HUNVKLUHꢀ6/ꢋꢀꢅ<'ꢀ
7HOꢃꢀꢄꢋꢈꢊꢅꢀꢊꢋꢋꢉꢅꢎ
)D[ꢀꢄꢋꢈꢊꢅꢀꢊꢊꢋꢋꢊꢊ
+HOSOLQHꢀꢄꢋꢈꢊꢅꢀꢊꢈꢎꢉꢈꢈ
90561147 REV 0
L-0
3/10
|